sumler - american office services

_. .-. '-

Sumler CoatingsT

"

Product: Nu-Charge-A-Thane™ Electrostatic Coating Component B, High Gloss (155) Semi-Gloss (154).

Type: Two Component Acrylic Urethane

Description: A superior, high performance acrylic urethane that combines superb corrosion and chemical resistance with exceptional gloss retention and exterior weather ability unequaled by conventional high-grade enamels. Designed specifically for exterior use with electrostatic, airless, and conventional spray equipment. Brush for touch-up only.

Uses: This isocyanate cured acrylic urethane is a superior exterior coating for metal buildings, extrusions, wrought iron railings, fencing, outdoor furniture, recreational equipment and machinery of all types, where added protection is desired. When used with recommended primer, NuCharge-A-Thane™ topcoats provide outstanding resistance to gasoline, occasional splash and spillage of organic solvents including xylene, alcohols, oil, mineral spirits, and salt water. Temperature resistant to 250° F continuous, and 300° F intermittent.

Mixing: NuCharge-A·Thane™ is a twocomponent system consisting of the base (component B) and catalyst (component A). Both components' temperature must be above 55° F before intermixing. Mixing ratio is 4 parts component B to 1 part component A by volume. Thoroughly mix by mechanical agitation prior to use. Do not mix more paint than can be sprayed in a normal working day. This product requires NO induction time, and has a pot life of approximately 8 hours. DO NOT USE CATALYZED MATERIAL THAT HAS EXCEEDED ITS POT LIFE.

TECHNICAL INFORMATION SHEET

March 2005

NU-CHARGE IT® Electrostatic Coatings

Surface Preparation: Surface to be painted must be clean and free of moisture, oil, grease, loose paint, rust, polish and waxes. Acrylic urethanes are especially sensitive to moisture.

Coverage: Varies by color, one catalyzed gallon will cover approximately 600 sq. ft. at 1 mil. Dry film thickness.

Sheen: High Gloss-90° minimum on a 60° gloss meter. Semi Gloss-50°-55° on a 60° gloss meter.

Flash Point: In excess of 80°F.

Pot Life: 8 Hours.

Reduction: Not recommended. If desired use Xylene or NuCharge It Reducer (560X1005).

Clean Up: Xylene or NuCharge It Reducer (560X1005). DO NOT LEAVE SOLVENTS OR PAINT IN PAINT LINE, FLUSH COMPLETELY.

Primer: Recommended two-component epoxy primer.

Dry Times: To Touch - 30 minutes Dry to Handle - 2 - 3 hours Recoat - When Dry to touch.

*NOTE: Pot life will decrease if temperature exceeds 75°F.

Warning: THIS ISOCYANATE CURED ACRYLIC URETHANE SHOULD BE APPLIED OUTDOORS. IF APPLIED INDOORS, A PROPERLY VENTED SPRAY BOOTH AND FRESH AIR RESPIRATOR SHOULD BE USED.

05/07 Sumter Coatings, Inc. /2410 Hwy 15 South, Sumter, SC 29154

The technical data furnished are true and accurate 10 the best of our knowledge at the date of issuance. It is subject to change without prior notice. II is suggested that the user verify with Sumter Coatings, Inc. prior 10 specifying or ordering. Test results are believed to be reliable, however, no guarantee of accuracy is given or implied. We guarantee all products 10 conform 10 Sumler Coatings, Jne. qualily control standards. Liability, if any. is limited 10 replacement of product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumter Coatings, Inc. including filness for a particular purpose.

0- -

.....

-_: ---'r--

Sumler Coatings™

Product: Nu-Charge It® Electrostatic Enamel - Gloss (181 Line) Semi-Gloss (182 Line)

Description: A single component modified acrylic enamel. Specifically formulated for interior or exterior use with both electrostatic and conventional spray equipment. When applied over properly prepared surfaces, this enamel provides a high quality finish unequaled by conventional enamel paints.

Uses: Recommended for all metal surfaces (especially school lockers), which have been previously coated with unknown finishes that may be susceptible to lifting by stronger solvents used in urethanes and epoxies.

Surface Preparation: Surface to be painted must be clean and free of oils, grease, loose paint, rust, polish, waxes and moisture. Feathering around scratches IS recommended because certain surfaces may lift when coated. A quick test should be conducted in an inconspicuous area to determine if a base coat should be removed or primed.

Coverage: Varies by color, one gallon will cover approximately 550 sq. ft. at 1 thickness. STIR THOROUGHAPPLICATION.

mil. LY

Dry BEF

film ORE

Sheen: High Gloss - 85° min.

Flash Point: In excess of 100°F.

Thinning: Not recommended. If desired, use Nu-Charge It 105+ reducer (560XI005)_


NU-CHARGE IT® Electrostatic Enamel

Clean Up: Use Nu-Charge It® 105+ reducer for equipment and utensils. DO NOT LEAVE SOLVENTS IN PAINT LINES, FLUSH COMPLETELY.

Pencil Hardness: IH +

Primer: If needed, use Nu-Charge It® Rust Inhibitive Epoxy Primer or Nu-Charge® It E3 Primer or contact your Sumter Coatings representitive.

Dry Time: To Touch - 40 Min. Tack Free - 1.5 Hrs.

Surface Temperature for painting: illll1lmum.

Pot Life: NIA

Shelf Life: 2 years

01/07

Sumter Coatings, Inc. /2410 Hwy 15 South, Sumter, SC 29154

The technical data furnished are true and accurate to the besl of our knowledge at the date of issuance, It is subject to change without prior notice. It is suggested that the user verify with Sumter Coatings, Inc. prior to specifying or ordering. Test results are believed 10 be reliable, however, no guarantee of accuracy is given or implied. We guarantee all products to conform to Sumter Coatings, Inc. quality control standards. Liability, if any, is limited to replacement of product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumter Coatings, Inc. including fitness for a particular purpose.

~~- -,

-~. -...-

~-

Sumler Coalings™

Product: Nu-Charge It® Electrostatic Epoxy Base Component B, ttS-line.

Type: Two component Polyamide Epoxy Resin.

Description: A superior, high performance epoxy coating specifically designed for interior use on all metals and steel where extra protection and durability is needed.

Uses: Offices furniture, bathroom partitions, medical equipment, kitchen appliances, and machinery. Nu-Charge It® epoxy when cured is highly resistant to many acids, alkaline solutions, detergents, oils, and solvents. Nu-Charge It® epoxy has a tenacious adhesion characteristic which creates adhesion to almost any substrate.

Mixing & Application: Thoroughly mix components A and B at a 1: I ratio by volume and allow a 20 minute induction time prior to spraying. This product may be applied by brush, roller, conventional spray, airless, and HVLP. Do not use in heated airless equipment, as it will gel lines of the heater.

Surface Preparation: Surface to be painted must be clean and free of oils, grease, loose paint, rust, polish, waxes and moisture. Feathering around scratches is recommended. Light sanding with 220 or 280 grit sandpaper is recommended. For severe metal contamination abrasive blast to SSPC-SP-6 commercial blast before painting.

Coverage: One gallon of catalyzed material will cover approximately 660 sq. ft. @ 1 (one) mil dry film thickness.

Sheen when catalyzed with: 115X2222A= High gloss 114X4444A= Semi gloss 113X6666A= Satin gloss


NU-CHARGE IT® ELECTROSTATIC COATINGS

Flash Point: Above 105°F. minimum.

Colors: Full range

Heat Resistant: 250°F.

Pot Life: @ 70° F Pot Life is 18 hrs.

Reduction: Not recommended, if needed use NuCharge It® 105+ Reducer (560X 1005)

Recommended Primer: Call your Sumter Coatings representative for recommendations.

Physical Properties: Weight per gallon- 11.44 Ibs. Solids by Weight- 71.02 % Solids by Volume- 45.55 %

Dry Times: Tack Free- 30 minutes Handle- I hour Recoat- Ihour Full cure- 7 days Heat cure- 250°F for 30 min.

Times can be accelerated using Nu-Charge It Epoxy Accelerator (480X4530).


Shelf Life: 2 years (non activated).

Packaging: I full gallon (128 fluid ounces). 1 Kit (color and catalyst) combined makes 2 full gallons.

Clean Up: Use Nu-Charge It® 105+ reducer for equipment and utensils.

03/06

Sumter Coatings, Inc. / 2410 Hwy 15 South, Sumter, SC 29154

The technical data furnished are true and accurate to the best of our knowledge at the date of issuance. It is subject to change without prior notice. It is suggested that the user verify with Sumter Coatings, Inc. prior to specifying or ordering. Test results are believed to be reliable, however, no guarantee of accuracy is given or implied. We guarantee all products to conform to Sumter Coatings, Inc. quality control stan~

dards. Liability, if any, is limited to replacement of product. No other warranty or guarantee of any kind, expressed OJ: implied, is made by Sumler Coatings, Inc. including fitness for a particular purpose

1

1-· -,

.... ....01

-- ~;-rl

Sumler Coatings™

EZ Electrostatic Universal Primer is a universal heavy duty rust inhibitive primer that can be topcoated with most paints, including epoxies and urethanes. This product was formulated to spray with electrostatic equipment without any adjustments to the paint. EZ Electrostatic Universal Primer can also be used as a barrier coat between previously painted surfaces and topcoats containing strong solvents.

Ordering: Available in single gallons.

Technical Data

Type: Phenolic Modified Alkyd

Components: One

Colors: Gray and Red Oxide

Gloss: Flat

V.O.C: 3.4 Ibs. per gallon ± .2 Lbs.

Solids by Volume: 52 % ± 2 %

Flash Point: 45 0 F.

Shelf Life: I year

Temperature Resistance: 2000 F. Max.

Recommended Film Thickness: 2 - 2.5 dry film

Spreading Rate: 810 sq. ft. per gal. @ 1 mil, 324-405 sq. ft. per gal. @ recommended dft.

Pot Life: N/A


EZ ELECTROSTATIC UNIVERSAL PRIMER

1169 GRAY 0866 RED OXIDE

EZ Electrostatic Universal Primer is used for:

Ornamental Iron Structural Steel Misc_ Metals Tanks General Maintenance Process Equipment

Surface Preparation: Surface must be clean, dry, and free from any contaminants including oil, grease, dirt, loose rust, loose paint, or loose mill scale. This product performs well over surfaces cleaned according to SSPC-SP-3 Power Tool Cleaning. In severely cOlTosive environments, SSPC-SP-6 Commercial Blast is recommended. Note: Excessive film or surface contamination may cause adhesion problems. If surface is sandblasted, it must be coated within 8 hours to avoid early rusting.

Mixing: Stir thoroughly prior to use.

Dry Time: To Touch: 20 minutes Tack Free: 40 minutes Re-coat: 2 hours.

Application: Electrostatic, Conventional or Airless Spray Equipment.

Thinning: Thinning not nom1ally required. If thinning is desired, use Sumter Coatings 560XlO05 Reducer.

Clean-up: Sumter Coatings 560XI005

05/05


e technical data furnished are true and accurate to the best of our knowledge at the date of issuance. II is subject to change without prior notice. II is suggested that the user verify with Sumler Coatings, Inc. prior to specifying or ordering. Test results are believed to be reliable, however, no guarantee of accuracy is given or implied. We guarantee all products to conform to Sumter Coatings, Inc. quality control stan· dards. Liability, if any, is limited to replacement of product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumter Coatings, Inc. including fitness for a particular purpose.

, 1- ~

--: ---~r--

TECHNICALSumler INFORMATION " SHEETCoalingsT

March 1997


Product: Nu-Charge It® 105+ Reducer (560X1005).

Type: Reducer

Description: A special solvent blend formulated especially for electrostatic coatings.

Uses: Use as a reducer and clean up solvent for all electrostatic products. NuCharge It® 105+ reducer will provide the ultimate results desired when reducing electrostatic products without affecting the polarity. NOTE: May also be used to thin Nu-Charge It® Electrostatic Epoxy as it nears the end of its pot life. DO NOT REDUCE COLD PAINT (as temperatures increase, paint will thin accordingly).

Flash Point: In excess of 1050 F. Considered a "safe solvent".

Pot Life: N/A

Shelf Life: N/A

Container Size: 1 gal., 5 gal., 55 gal. drum.


The technical data furnished are true and accurate to the best of our knowledge al the dale of issuance. It is subject 10 change without prior notice. It is suggested that the user verily with Sumter Coatings, Inc. prior to specifying or ordering. Test results are believed to be reliable, however, no guarantee of accuracy is given or implied. We guarantee all products to conform to Sumter Coatings, Inc. quality control standards. Liability, if any, is limited to replacement of product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumter Coatings, Inc. including fitness for a particular purpose.

- -~ ~J-

TECHNICALSumler INFORMATIONCoalings™ SHEET


Product: Nu-Charge It® Anti-Graffiti Additive (480X1457)

Components: One

Description: An additive used to make Nu-Charge It® Electrostatic Coatings graffiti resistant.

Mixing: Not to exceed 3 to 5 ounces per gallon while agitating or stirring.

Flash Point: 108°F.

Pot Life: 1 year

Uses: School lockers, machinery, office furniture, hospital equipment, bathroom partitions, metal buildings and any other areas where extra protection is needed.

Note: If repainting, hand or mechanical sanding Is required.

07/06


The technical data furnished are true and accurate 10 the best of our knowledge at the date of issuance. It is subject 10 change without prior notice. It is suggested that the user verify with Sumler Coatings, Inc. prior to specifying or ordering. Test results are believed to be reliable, however, no guarantee of accuracy is given or implied. We guarantee all products to conform to Sumter Coatings, Inc. quality control standards. Liability, if any, is limited to replacement of product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumter Coatings, Inc. including fitness lor a particular purpose.

1

-~ -~

~,-

Sumler CoatingsT

"

E3 Primer

E3 Primer is an Epoxy Ester Primer, which is a rust inhibitive, single - pack epoxy. The epoxy ester resin, along with other key ingredients, makes this a product with excellent adhesion properties. E3 is lead and chrome free. And offers excellent weather and corrosion resistance.

Ordering: Available in single gallons and five gallon pails

Technical Data

Type: Epoxy Ester

Components: One

Colors: 1368 Gray - Green 1370 Off White

Gloss: Flat

V.O.C: 4.5 - 4.9 Ibs. per gallon

Solids by Volume: 35% ± 2%

Flash Point: 580 F.

Shelf Life: 1 year

Temperature Resistance: 2000 F. Maximum

Surface Preparation: Surface must be clean and dry. Remove all contaminants including oil, grease, loose paint, dirt or any other contaminants. This product performs well over surfaces cleaned according to SSPC-SP-3 Power Tool Cleaning. In severely corrosive environments, SSPC-SP-6 is recommended.

Application: Electrostatic Spray, brush, roll, or conventional spray. Excessive film or surface contamination may cause adhesion problems and solvent entrapme.l1t.



E3 Primer can be used for:

Hand Rails Cylinders Ornamental Iron Structural Steel Aq-Chem Equipment Process Equipment Plus Many Other Uses

Mixing: Stir thoroughly prior use.

Recommended Film Thickness: 2.0 - 2.5 mils dry film.

Spreading Rate: 560 sq. ft per gal. @ I mil. 224 - 280sq. ft. per gal. @ recommended dft.

Pot Life: NIA

Dry Time: To Touch: 30 minutes Tack Free: 45 minutes Re-coat: 2 hours

Note: When top coating with the Nu Charge It! Epoxy, re-coat before 4 hrs. or wait 24 hrs.

Thinning: For spray application, thin as necessary with XL Thinner or Xylol, up to 15%. Thilming not normally required for electrostatic spray, brush or roll application.

Clean-up: XL Thinner or Xylol

05/07 ~umter Coatings, Inc./2410 Hwy 15 South, Sumter, SC 29154

The technical data furnished are true and accurate to the best of our knowledge at the date of issuance. It is subject to change without prior notice. It is suggested that the user verify with Sumler Coatings, Inc. prior to specifying or ordering. Test results are believed to be reliable, however, no guarantee of accuracy is given or implied. We guarantee all products 10 conform 10 Sumler Coatings, Inc. quality control standards. Liability, if any, is limited to replacement of product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumter Coatings, Inc. including fitness for a particular purpose.

....

._.. ~.r--



Product: Fisheye Eliminator (480X4506)

Type: 100% Silicone Fluid

Description: An additive designed to eliminate fisheyes and aid in product leveling.

Container: Available in Quarts and Gallons.

Mixing: Add NO MORE than 1/32 of an ounce to one gallon of catalyzed material.

Shelf Life: N/A

Pot Life: N/A

Flash Point: 135 0 F (55 0 C).

01/04


The technical data furnished are true and accurate 10 the best of our knowledge at the date of issuance. It is subject to change without prior notice. It is suggested that the user verify with Sumler Coalings, Inc. prior to specifying or ordering. Test results are believed to be reliable, however, no guarantee of accuracy is given or implied. We guarantee all products to conform to Sumter Coatings, Inc. quality control sIandards. Liability, if any, is limited 10 replacement of product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumter Coatings, Inc. including fitness for a particular purpose.

--~ --',.....



Product: Flatting Agent (480X1405)

Components: One

Description: An additive used to reduce the gloss/sheen of a normal gloss or semi-gloss paint.

Mixing: Product should be mechanically agitated before and after adding to paint. 4 fluid ounces will drop gloss approx. 35 to 45%. For example: 5 to 6 ounces of Flatting Agent will change a semi-gloss paint of 50 degrees gloss to a satin finish of approx. 25 degrees gloss.

Flash Point: >1 05°F.

Pot Life: 1 year.

11/06


The technical data furnished are true and accurate 10 the besl of our knowledge at the date of issuance. II is subject to change without prior nolice. It is suggested that the user verify with Sumter Coatings, Inc. prior to specifying or ordering. Test results are believed 10 be reliable, however, no guarantee of accuracy is given or implied. We guarantee all products to conform to Sumter Coatings, Inc. quality control stan· dards. Liability, if any, is limited 10 replacement of product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumler Coatings, Inc. including fitness for a particular purpose.

1

-,' '-!r-

TECHNICALSumler INFORMATIONCoatings™ SHEET


Product: NuCharge It® Polar Prep 480X4570

Description: NuCharge It® Polar Prep is a solution that is used to make non-conductive surfaces such as wood, laminates, plastic, fiberglass, and etc. conductive. Polar Prep prepares these nonconductive surfaces for application of Sumter Coatings NuCharge It Epoxy, NuCharge It Enamel, NuChare-A-Thane, and electrostatic primers.

Type: Polar Solution

Components: One

Flash Point: 105° F.

Mixing: Mix 1 part of Polar Prep to 4 - 6 parts of 560X1005 (105 Reducer) and agitate slowly.

Surface Preparation: Surface must be dry and free of dirt, oil, grease and any other foreign contaminants.

Application: Product can be brushed, wiped or sprayed. If sprayed, a very low pressure should be used. Entire surface should be coated and allowed about 20 - 30 minutes to dry before painting. Painting should be done within a 4 hour period.

Shelf Life: 1 year

01/04

Sumter Coatings, Inc./2410 Hwy 15 South, Sumter, SC 29154

The technical dala furnished are true and accurate to the best 01 our knowledge at the date 01 issuance. It is subject to change without prior notice, II is suggested that the user verify with Sumler Coatings, Inc prior to specifying or ordering. Test results are believed to be reliable, howeller, no guarantee of accuracy is given or implied. We guarantee all products 10 conform 10 Sumler Coatings, Inc. quality control stan· dards. Liability, if any, is limited to replacement of product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumter Coatings, Inc. including fitness for a particular purpose

---

1- ~

--~ ~,-

._~

Sumler CoatingsT

"

Product: Rust Inhibitive Epoxy Primer Base Component B, (l14D7185B).

Type: Two-component Polyamide Epoxy Primer.

Description and Uses: A superior, high performance epoxy primer specifically designed for interior or exterior use on all metals and steel where extra protection and durability is needed.

Mixing & Application: Thoroughly mix components A (114X4444A) and B (114D7185B) at a I: I ratio by volume and allow a 20 minute induction time prior to spraying. This product may be applied by blUSh, roller, conventional spray, airless, and HVLP. Do not use in heated airless equipment, as it will gel lines of the heater.

Surface Preparation: Surface to be painted must be clean and free of oils, grease, loose paint, lUSt, polish, waxes and moisture. For severe metal contamination abrasive blast to SSPC-SP-6 commercial blast before priming.

Recommend Film Thickness: 2 to 4 mil dry film thickness.

Coverage: One gallon of catalyzed material will cover approximately 330 sq. ft. @ 2 mil dry film thickness.

Flash Point: Above 105°F. minimum.


NuCharge-lt® ELECTROSTATIC COATINGS


Pot Life: @ 70° F Pot Life is 18 hrs.

Surface Temperature for painting: 45°F nummum.

Reduction: Not recommended, if desired, use u-Charge It® 105 Reducer (560XI005).

Recommended Topcoat: Industrial Enamels, Epoxies, Urethanes and most heavy duty industrial topcoats.

Physical Properties: Weight per gallon- 11.44 Ibs. Solids by Weight- 71.02 % Solids by Volume- 45.55 %

Dry Times: Tack Free- 30 minutes Handle- 2 hour Recoat- 2 hour Full cure- 7 days Heat cure- 250°F for 30 min.


Shelf Life: I years (non activated).

Packaging: I full gallon of Epoxy Primer (114D7185B), and I full gallon of Epoxy Catalyst (114X4444A). I Kit (primer and catalyst) combined makes 2 full gallons.

Clean Up: Use Nu-Charge It® 105+ reducer for equipment and utensils.

01/07

Sumter Coatings, Inc. /2410 Hwy 15 South, Sumter, SC 29154

The technical data fumished are true and accurate to the best of our knowledge al the date of issuance. It is subject to change without prior notice. It is suggested that the user verify with Sumter Coatings, Inc. prior to specifying or ordering. Test results are believed to be reliable, however. no guarantee of accuracy is given or implied. We guarantee all products to conform to Sumter Coatings, Inc. quality control standards. LIability, if any, is limited to replacement 01 product. No other warranty or guarantee of any kind, expressed or implied, is made by Sumter Coatings, Inc. including fitness for a particular purpose.

sumler - american office services

Documents