submitted to - adhesives technologyatcepoxy.com/wp-content/uploads/submittal-generator-2300.pdf ·...

SUBMITTED TO:

SUBMITTED PRODUCT:

SPECIFIED PRODUCT:

SECTION: PAGE: PARAGRAPH: DETAIL/SHEET NO.:

DESCRIPTION OF APPLICATION:

PRODUCT INFORMATION:

TO: SUBMITTAL DATE:

COMPANY NAME:

PROJECT:

This submittal package contains the product data sheet, installation instructions and safety data sheet needed for evaluation of this submittal request

SUBMITTED BY: NAME: SIGNATURE:

COMPANY NAME:

ADDRESS:

PHONE: EMAIL:

FAX: DATE:

FOR ARCHITECT/ENGINEER USE: APPROVED: APPROVED AS NOTED: NOT APPROVED:

BRIEF EXPLANATION, IF NOT APPROVED:

BY: DATE:

REMARKS:

Adhesives Technology Corp. ▪ Florida, USA ▪ (800) 892-1880 ▪ www.atcepoxy.com

ULTRABOND 2300

Revision 4.0

1

Bonding Epoxy

ASTM C881-10 Type I, II, IV & V Grade 3 Class C AASHTO M235

Multiple DOT Listings

(See ATC website for current list of Department of Transportation Approvals throughout the

United States and Canada)

Installation & Coverage: See Manufacturer’s Printed Installa-tion Instructions (MPII) available within this Technical Data Sheet (TDS). Due to occasional updates and revisions, always verify that you are using the most current version of the MPII. In order to achieve maximum results, proper installation is impera-tive. Clean Up: Always wear appropriate protective equipment such as safety glasses and gloves during cleanup. Clean un-cured materials from tools and equipment with mild solvent. Cured material can only be removed mechanically. Limitations & Warnings: Do not thin with solvents, as this may inhibit proper curing Not recommended for any application where there may be a

sustained tensile load, including overhead applications Safety: Please refer to the Safety Data Sheet (SDS) for UL-TRABOND 2300. Call ATC for more information at 1-800-892-1880. Specification: The bonding agent shall be a two compo-nent, 1:1 mix ratio epoxy system supplied in pre-measured con-tainers. The adhesive must meet the requirements of C881-14 specification for Type I, II, IV, and V, Grade 3 Class C. When cured 7 days and at a temperature of 75 °F (24 °C), the bonding agent shall have a compressive strength of 10,220 psi (70.5 MPa) per ASTM D695 and a tensile strength of 3,316 psi (22.9 MPa) per ASTM D638. The bonding agent shall be ULTRA-BOND 2300 from Adhesives Technology Corp., Pompano Beach, Florida.

ULTRABOND® 2300 is a high strength, non-sag, multi-purpose bonding agent, which can be used in temperatures between 60 °F and 110 °F (16 °C and 43 °C).

Product Description

General Uses & Applications Bonding hardened concrete to hardened concrete Bonding freshly mixed concrete to hardened concrete Advantages & Features

Extended working time Non-sag Low VOC content Moisture insensitive allowing installation and curing in damp

environments

Availability: Adhesives Technology Corp. (ATC) ULTRA-BOND products are available through select distributors who can provide you with all of your construction needs. Please contact ATC for a distributor near you or visit our website at www.atcepoxy.com to search by zip code.

ASTM C881-14

Type I, II, IV & V Grade 3 Class C

AASHTO M235

(See ATC website for current list of Department of

Transportation approvals throughout the United States)

Color & Ratio: Part A (Resin): Beige, Part B (Hardener): Dark Gray, Mixed: Concrete Gray, Mix Ratio: 1:1 by volume Storage & Shelf Life: 24 months when stored in unopened containers in dry conditions. Store between 40 °F (4 °C) and 95 °F (35 °C).

Revision 4.0

2

Bonding Epoxy

MATERIAL SPECIFICATION

TABLE 1: ULTRABOND 2300 Adhesive

Package Size 1 Gallon (3.8L)

Kit

Part # BUG-2300

Case Qty 1

Pallet Qty 75 kits

Pallet Weight (lbs) 752

BUG-2300

ORDERING INFORMATION

TABLE 2: ULTRABOND 2300 performance to ASTM C881-141,2

Property Cure Time

ASTM Standard Units

Sample Conditioning Temperature

75 °F

(24) °C

Gel Time - 60 Gram Mass ---- C881 minutes 28

Tack Free Cure Time

(30 mil Thin Film) ---- D2377 hours 3

Pot Life3 ---- ---- minutes 23

Compressive Yield Strength

7 day

D695

psi 10,220 (MPa) (70.5)

Compressive Modulus psi 213,000 (MPa) (1,468.6)

Tensile Strength

D638

psi 3,316 (MPa) (22.9)

Tensile Elongation % 2.9

Bond Strength

2 day

C882

psi 3,600 (MPa) (24.8)

14 day psi 4,060 (MPa) (28.0)

Consistency or Viscosity ---- C881 ---- Non-sag

Heat Deflection Temperature 7 day D648 °F 121 (°C) (49.4)

Water Absorption 14 day D570 % 0.41

Linear Coefficient of Shrinkage ---- D2566 % 0.0022

1. Results based on testing conducted on a representative lot of product. Average results will vary according to the tolerances of the given property. 2. Full cure time is listed above to obtain the performance as listed for the corresponding material property. 3. Pot life is measured as the workable time, in minutes, of the full Bulk Unit Gallon mixed. At a temperature of 110 °F (43 °C) the pot life is 6.5 minutes.

MATERIAL SPECIFICATION

Revision 4.0

3

Bonding Epoxy

Surface Preparation

Concrete must be clean and profiled or textured. All dirt, oil, debris, wax, grease or dust must be removed. Remove any loose concrete or rocks from the surface area where the application of the bonding adhesive will be applied. New concrete must be a minimum of 28 days old. Prepare the surface mechanically using a scarifier, shotblaster, bushhammer or other equipment that will give the surface

the profile needed for the application. A roughened surface is imperative to good adhesion. Surfaces may be damp (or dry) however there should be no standing water.

Mixing Instructions

NOTE: Thoroughly stir each component separately before mixing together.

1. Pour the total contents of Part “B” (hardener) into the Part “A” pail (resin) OR proportion equal parts by volume of both Part “A” and Part “B” into a clean pail. Be sure that the components are mixed at an exact 1:1 ratio by volume.

2. Mix thoroughly with a low speed drill (400 – 600 rpm) with a Jiffy mixing paddle or similar. Carefully scrape the sides and the bottom of the container while mixing. Keep the paddle below the surface of the material to avoid entrapping air. Proper mixing will take at least 3 minutes and when well mixed the material will be free of streaks or lumps.

3. Mix only the amount of material that can be used before the pot life expires.

Bonding fresh concrete to hardened concrete: Using a brush or roller, apply an even coat of the mixed ULTRABOND 2300 epoxy to the clean and prepared concrete surface. While the epoxy is still tacky, place fresh concrete over the top of the mixed epoxy.

Bonding hardened concrete to hardened concrete: Using a brush or roller, apply an even coat of the mixed ULTRA-

BOND 2300 epoxy to both concrete surfaces and be sure to fill all gaps between the mating concrete surfaces. Spall Repair Preparation: Cut into the sound concrete using a grinder with a 4-1/2 diamond blade or tuck point diamond

grinding wheel and prepare the area to be repaired as noted above under Surface Preparation. Pour mixed neat ULTRA-BOND 2300 into the repair area and smooth out with a trowel to create a smooth surface.

Applications

INSTALLATION INSTRUCTIONS (MPII)

Safety Data Sheet Ultrabond 2300 Created On: 03/20/2014 Revision Date: 02/08/2015 Version: 2.0

Page 1 of 12

1. Product and Company Identification

Product Name: Ultrabond 2300 (Part A) Product Use: Anchoring

Company Identification: Emergency Phone: ADHESIVES TECHNOLOGY CORP. Chem-Tel: 450 East Copans Road 1.800.255.3924 (24hrs) Pompano Beach, FL 33064 Contact Phone: 1.800.892.1880 (9:00a.m. – 5:00p.m. EST)

____________________________________________________________________________________________________ 2. Hazards Identification (Part A)

GHS Classification

Health Physical Environmental

Skin Irritant Cat 2 Eye Irritant Cat 2B Skin Sens 1 Carcinogen Cat 1A

Not Classified Toxic to Aquatic Life Cat-2

GHS Label: Warning:

Eye Irritant Skin Irritant Skin Sensitizer

Emergency Overview May cause skin sensitization Causes skin and eye irritation May cause cancer Wash skin thoroughly after handling Avoid breathing fume/gas/mist/vapors/spray Wear protective gloves/ protective clothing/ eye protection/ face protection Use outdoors or in a well-ventilated area

Primary Route of Exposure Eyes, skin and oral

Carcinogenicity This product or one of its ingredients present at 0.1% or more IS listed as a carcinogen or suspect carcinogen by NTP, IARC, Prop 65 or OSHA.

http://en.wikipedia.org/wiki/File:GHS-pictogram-exclam.svg


Page 2 of 12

This product contains titanium dioxide which IARC has classified as a Group 2B carcinogen (possibly carcinogenic to humans). Evidence is based on sufficient animal testing as a result of long-term inhalation at high concentrations of respirable amounts of titanium dioxide. Because this product is in liquid or paste form, it does not pose a dust hazard; therefore, this classification is not relevant. (Note: sanding of this product will create a possible dust hazard).

This product contains crystalline silica (quarts sand). IARC has classified crystalline silica as a Group 1 carcinogen. Both IARC and NTP consider silica as a known human carcinogen. Evidence is based on the chronic and long-term exposure workers have had to respirable sized crystalline silica dust particles. Because this product is in liquid or paste form, it does not pose a dust hazard; therefore, this classification is not relevant. (Note: sanding of this product will create a possible silica dust hazard)

_________________________________________________________________________________________________ 3. Composition/ Information on Ingredients (Part A)

CAS Number Content% Chemical Name 25085-99-8 70 - 90 Diglycidyl Ether of Bisphenol A 13463-67-7 1 - 5 Titanium Dioxide 14808-60-7 0.1 – 1 Quartz Silica Sand (Crystalline Silica) Proprietary 15 – 30 Non Hazardous

____________________________________________________________________________________________________ 4. First Aid Measures (Part A)

Inhalation: Move to fresh air; give oxygen if breathing is difficult. Call a physician if symptoms persist. Eyes: Immediately flush eyes with plenty of water for at least 15 minutes. Call a physician if symptoms persist. Skin: Remove contaminated clothing. Wash with mild soap and water. Get medical attention if skin irritation or dermatitis persists. Ingestion: Give plenty of water. DO NOT induce vomiting. Call a physician immediately. Other: Referral to a physician is recommended if there is any question about the seriousness of the injury/exposure. If sensitization occurs, future contact with the material should be avoided.

____________________________________________________________________________________________________ 5. Fire Fighting Measures (Part A)

Flash Point: 204 0C (>400 0F) Flammable Limits: N/A Extinguisher Media Carbon Dioxide, Dry Chemical, Water Fog

Unusual Fire and Explosion Hazard None known. Thermal Decomposition can be formed. Special Fire Fighting Procedures Firefighters must wear self-contained breathing apparatus and full protective clothing to prevent contact with toxic and/or irritating fumes.

____________________________________________________________________________________________________ 6. Accidental Release Measures (Part A)


Page 3 of 12

Personal Precautions: Avoid all personal contact. In enclosed areas, cleanup personnel should wear self-contained breathing apparatus. Environmental Precautions Cover spills with sawdust, vermiculite, or other absorbent material to minimize spreading of the material before collecting.

____________________________________________________________________________________________________ 7. Handling and Storage (Part A)

Handling: Avoid contact with eyes, skin and clothing. Avoid inhalation of vapors. Use with adequate ventilation. Use appropriate personal protection equipment (Section 8). Wash thoroughly after handling. Storage: Store in a cool dry place away from direct sunlight. Keep from freezing. Recommended storage temperature range in between 4 ºC and 35 ºC (40ºF and 95º F).

____________________________________________________________________________________________________ 8. Exposure Control and Personal Protection (Part A)

Exposure Guidelines

Component CAS# OSHA PEL TLV

Titanium Dioxide 13463-67-7

15 mg/m3 10 mg/m3

Quartz Silica Sand (Crystalline Silica)

14808-60-7

0.1 mg/m3 0.025 mg/m3

Engineering Measures: Use local and general exhaust ventilation to maintain airborne concentrations below TLV. Suitable respiratory equipment should be used in cases of insufficient ventilation or where operational procedures demand it.

Personal Protective Equipment Respiratory Protection None normally required. Use a NIOSH approved organic vapor chemical cartridge respirator when air movement is inadequate to control vapor build-up.

Eye/Face Protection Wear splash proof chemical goggles/ full face shield if there is a potential for splashing. Skin / Body Protection Wear Suitable gloves (neoprene, nitrile rubber or PVC) and protective clothing to mitigate exposure.

Other Protective Clothing or Equipment Use protective clothing which is chemical resistant to this material. Safety shoes and boots should also be chemical resistant.

____________________________________________________________________________________________________ 9. Physical and Chemical Properties (Part A)


Page 4 of 12

Appearance: White Paste Evaporation Rate: N/D Odor: Slight Odor Solubility in Water: Insoluble Specific Gravity(g/cc): 1.4 Vapor Density(air = 1): N/D Vapor Pressure: N/D VOC Content: N/D pH: N/D Boiling Point: N/D

____________________________________________________________________________________________________ 10. Stability and Reactivity (Part A)

Stability: Stable

Thermal Decomposition: Can yield CO, CO2 and organic Nitrogen compounds. Incompatibility: Strong acids, peroxides, and other oxidizing agents

Conditions to avoid: Exposure to excessive heat and storage above 35°C (95°F) will shorten shelf

life. ____________________________________________________________________________________________________ 11. Toxicological Information (Part A)

Acute Oral Toxicity: Not Determined Acute Dermal Toxicity: Not Determined

Acute Inhalation Toxicity: Not Determined

Skin Irritation: Irritating to skin The product has not been tested. The statement has been derived from the properties of the individual components. Eye Irritation: Irritating to eyes. The product has not been tested. The statement has been derived from the properties of the individual components.

Respiratory Irritation: Inhalation of vapors or mists may cause irritation to the respiratory system. Sensitization: May cause allergic skin reaction and irritation to the respiratory system.


Page 5 of 12

The product has not been tested. The statement has been derived from the properties of the individual components. STOT – single exposure Not Determined STOT – Repeated Exposure Not Determined

Carcinogenicity Classification: Quartz Silica Sand (Crystalline Silica): IARC Group 1: Known human carcinogen based on human evidence. Titanium Dioxide: IARC Group 2B: Possibly carcinogenic to humans. This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

____________________________________________________________________________________________________ 12. Ecological Information (Part A)

Fish: Diglycidyl Ether of Bisphenol A: Fathead minnow/LC50 (96hrs): >3.1mg/l Aquatic Invertebrates: Diglycidyl Ether of Bisphenol A: Water Flea Daphnis/EC 50 (48hrs): > 1.4mg/l Algae: No Data Available Microorganisms: Diglycidyl Ether of Bisphenol A: Bacteria, (Growth inhibition)/IC50 (18hrs): > 42.6mg/l Mobility: Considering the use of the substance, it is unlikely that significant environmental exposure in the air or water will arise.

____________________________________________________________________________________________________ 13. Disposal Considerations (Part A)

If the material as supplied becomes a waste, dispose in accordance with federal, state and local regulations.

____________________________________________________________________________________________________ 14. Transportation Information (Part A)

This product is not regulated as a hazardous material for transportation. ____________________________________________________________________________________________________


Page 6 of 12

15. Regulatory Information (Part A) NFPA Rating

Hazard Rating: 0 = minimal, 1 = Slight, 2 = moderate, 3 = severe, 4 = extreme Federal Regulations

CERCLA RQ SARA Title 311/312 Not Determined CA Prop 65 This product contains a chemical or chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm.

TSCA Listed or Exempt State Regulations:

State RTK NJ, MA, PA CAS# Chemical Name 25085-99-8 Diglycidyl Ether of Bisphenol A 13463-67-7 Titanium Dioxide

64741-65-7 Naphtha, Petroleum, Heavy Alkylate (NJ,PA) ____________________________________________________________________________________________________ 16. Other Information (Part A)

Hazard Communication: This SDS has been prepared in accordance with the federal OSHA Hazard Communication Standard

To the best of our knowledge, the information contained herein is accurate. However, Adhesives Technology Corp. does not assume any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Additional information is available upon request.

HMIS Rating

Health 2

Flammability 1

Physical Hazard 0

PPE B


Page 7 of 12

1. Product and Company Identification

Product Name: Ultrabond 2300 (Part B) Product Use: Anchoring

Company Identification: Emergency Phone: ADHESIVES TECHNOLOGY CORP. Chem-Tel: 450 East Copans Road 1.800.255.3924 (24hrs) Pompano Beach, FL 33064 Contact Phone: 1.800.892.1880 (9:00a.m. – 5:00p.m. EST)

____________________________________________________________________________________________________ 2. Hazards Identification (Part B)

GHS Classification

Health Physical Environmental

Skin Corrosion Cat 1B Serious Eye Damage Cat 1 Carcinogen Cat 1A Reproductive toxicity Cat 2

Not Classified Toxic to Aquatic Life Cat-2

GHS Label: Danger:

Corrosive to skin and eyes Reproductive toxicity Skin Irritant

Emergency Overview Causes skin burns Causes severe eye damage May cause cancer Suspected of damaging fertility Wash skin thoroughly after handling Avoid breathing fume/gas/mist/vapors/spray Wear protective gloves/ protective clothing/ eye protection/ face protection Use outdoors or in a well-ventilated area Avoid contact during pregnancy/while nursing

Primary Route of Exposure Eyes, skin and oral

Carcinogenicity This product or one of its ingredients present at 0.1% or more IS listed as a carcinogen or suspect carcinogen by NTP, IARC, Prop 65 or OSHA.

http://en.wikipedia.org/wiki/File:GHS-pictogram-acid.svg

http://en.wikipedia.org/wiki/File:GHS-pictogram-silhouete.svg


Page 8 of 12

This product contains crystalline silica (quarts sand). IARC has classified crystalline silica as a Group 1 carcinogen. Both IARC and NTP consider silica as a known human carcinogen. Evidence is based on the chronic and long-term exposure workers have had to respirable sized crystalline silica dust particles. Because this product is in liquid or paste form, it does not pose a dust hazard; therefore, this classification is not relevant. (Note: sanding of this product will create a possible silica dust hazard) ____________________________________________________________________________________________________ 3. Composition/ Information on Ingredients (Part B)

CAS Number Content% Chemical Name 84852-15-3 15 – 25 Nonyl phenol 68082-29-1 30 – 60 Liquid Polyamide Resin 14808-60-7 20 – 40 Quartz Silica Sand (Crystalline Silica)

____________________________________________________________________________________________________ 4. First Aid Measures (Part B)

Inhalation: Move to fresh air; give oxygen if breathing is difficult. Call a physician if symptoms persist. Eyes: Immediately flush eyes with plenty of water for at least 15 minutes. Call a physician if symptoms persist. Skin: Remove contaminated clothing. Wash with mild soap and water. Get medical attention if skin irritation or dermatitis persists. Ingestion: Give plenty of water. DO NOT induce vomiting. Call a physician immediately. Other: Referral to a physician is recommended if there is any question about the seriousness of the injury/exposure. If sensitization occurs, future contact with the material should be avoided.

____________________________________________________________________________________________________ 5. Fire Fighting Measures (Part B)

Flash Point: >93°C (200°F) Flammable Limits: N/A Extinguisher Media Carbon Dioxide, Dry Chemical, Water Fog

Unusual Fire and Explosion Hazard None known. Thermal Decomposition can be formed. Special Fire Fighting Procedures Firefighters must wear self-contained breathing apparatus and full protective clothing to prevent contact with toxic and/or irritating fumes.

____________________________________________________________________________________________________ 6. Accidental Release Measures (Part B)

Personal Precautions: Avoid all personal contact. In enclosed areas, cleanup personnel should wear self-contained breathing apparatus. Environmental Precautions


Page 9 of 12

Cover spills with sawdust, vermiculite, or other absorbent material to minimize spreading of the material before collecting.

____________________________________________________________________________________________________ 7. Handling and Storage (Part B)

Handling: Avoid contact with eyes, skin and clothing. Avoid inhalation of vapors. Use with adequate ventilation. Use appropriate personal protection equipment (Section 8). Wash thoroughly after handling. Storage: Store in a cool dry place away from direct sunlight. Keep from freezing. Recommended storage temperature range in between 4 ºC and 35 ºC (40ºF and 95º F).

____________________________________________________________________________________________________ 8. Exposure Control and Personal Protection (Part B)

Component CAS# OSHA PEL TLV

Quartz Silica Sand (Crystalline Silica)

14808-60-7

0.1 mg/m3 0.025 mg/m3

Engineering Measures: Use local and general exhaust ventilation to maintain airborne concentrations below TLV. Suitable respiratory equipment should be used in cases of insufficient ventilation or where operational procedures demand it.

Personal Protective Equipment Respiratory Protection None normally required. Use a NIOSH approved organic vapor chemical cartridge respirator when air movement is inadequate to control vapor build-up.

Eye/Face Protection Wear splash proof chemical goggles/ full face shield if there is a potential for splashing. Skin / Body Protection Wear Suitable gloves (neoprene, nitrile rubber or PVC) and protective clothing to mitigate exposure.

Other Protective Clothing or Equipment Use protective clothing which is chemical resistant to this material. Safety shoes and boots should also be chemical resistant.

____________________________________________________________________________________________________ 9. Physical and Chemical Properties (Part B)

Appearance: Black Paste Evaporation Rate: N/A Odor: Slight Odor Solubility in Water: Insoluble Specific Gravity(g/cc): 1.05 Vapor Density(air = 1): Non-Volatile Vapor Pressure: N/A VOC Content: N/D


Page 10 of 12

pH: N/D Boiling Point: N/A

_______________________________________________________________________________________________________________ 10. Stability and Reactivity (Part B)

Stability: Stable

Thermal Decomposition: Can yield CO, CO2 and organic Nitrogen compounds. Incompatibility: Strong acids, peroxides, and other oxidizing agents

Conditions to avoid: Exposure to excessive heat and storage above 35°C (95°F) will shorten shelf

life. _______________________________________________________________________________________________________________ 11. Toxicological Information (Part B)

Acute Oral Toxicity: Not Determined Acute Dermal Toxicity: Not Determined

Acute Inhalation Toxicity: Not Determined

Skin Irritation: Corrosive to skin The product has not been tested. The statement has been derived from the properties of the individual components. Eye Irritation: Severe damage to eyes. The product has not been tested. The statement has been derived from the properties of the individual components.

Respiratory Irritation: Inhalation of vapors or mists may cause irritation to the respiratory system. Sensitization: May cause allergic skin reaction and irritation to the respiratory system. The product has not been tested. The statement has been derived from the properties of the individual components. Carcinogenicity Classification: Quartz Silica Sand (Crystalline Silica): IARC Group1: Known human carcinogen based on human evidence. NTP (National Toxicology Program) has classified Crystalline Silica as a known human carcinogen.

_______________________________________________________________________________________________________________


Page 11 of 12

12. Ecological Information (Part B)

Acute Toxicity for: Fish: Liquid Polyamide Resin: Zebrafish /LC50 (96hrs): >5.0mg/l Aquatic Invertebrates: Liquid Polyamide Resin: Water Flea Daphnis/EC 50 (48hrs): > 7.07mg/l Algae: No Data Available Microorganisms: No Data Available

Mobility: Considering the use of the substance, it is unlikely that significant environmental exposure is the air or water will arise.

_______________________________________________________________________________________________________________ 13. Disposal Considerations (Part B)

If the material as supplied becomes a waste, dispose in accordance with federal, state and local regulations.

_______________________________________________________________________________________________________________ 14. Transportation Information (Part B)

DOT (US) CARTRIDGE: Limited Quantity, LTD QTY BULK – Corrosive Liquid, n.o.s. ( 4-Nonylphenol, branched), Class 8, UN 1760, PG III IATA/ICAO CARTRIDGE/BULK: Corrosive Liquid, n.o.s. (4-Nonylphenol, branched), Class 8, UN 1760, PG III IMDG CARTRIDGE/BULK: Corrosive Liquid, n.o.s. (4-Nonylphenol, branched) Class 8, UN 1760, PG III Marine pollutant: yes _______________________________________________________________________________________________________________

15. Regulatory Information (Part B)

HMIS Rating


Page 12 of 12

NFPA Rating

Hazard Rating: 0 = minimal, 1 = Slight, 2 = moderate, 3 = severe, 4 = extreme

Federal Regulations

CA Prop 65 This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

TSCA Listed State Regulations:

State RTK NJ, MA, PA CAS# Chemical Name 14808-60-7 Quartz Silica Sand (Crystalline Silica)

_______________________________________________________________________________________________________________ 16. Other Information

Hazard Communication: This SDS has been prepared in accordance with the federal OSHA Hazard Communication Standard

To the best of our knowledge, the information contained herein is accurate. However, Adhesives Technology Corp. does not assume any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Additional information is available upon request.

Health *3

Flammability 1

Physical Hazard 0

PPE B

submitted to - adhesives technologyatcepoxy.com/wp-content/uploads/submittal-generator-2300.pdf ·...

Documents