squeeze chute #191440 - hiqual equipment chute.pdf · do not modify the equipment without...

FROM ALL HINGED AND MOVING PARTSDURING OPERATION.

HI QUAL

SQUEEZE CHUTE #191440

WARNING!: KEEP HANDS & FINGERS AWAY

HI QUAL, 196 1/2 E. 6th St, SIOUX FALLS, SOUTH DAKOTA 571041-844-544-7825

MANUAL NO: 208682 CREATED: 01/2017

CONTENTS

SAFETY PG 3

REPAIR/REPLACEMENT PARTS PG 4-5

FIG. A- MAIN ASSEMBLY BREAK DOWN PG 6

FIG. B- MAIN FRAME ASSEMBLY PG 7

FIG. C- LH LARGE DOOR ASSEMBLY PG 8

FIG. D- RH LARGE DOOR ASSEMBLY PG 9

FIG. E- SLICK DOOR ASSEMBLY PG 10

FIG. F- LH PALP DOOR ASSEMBLY PG 12

FIG. G- RH PALP DOOR ASSEMBLY PG 13

RATCHET LOCK INSTALLATION PG 13

ROPE INSTALLATION PG 14

AUTO/MANUAL HEAD GATE (OPTIONAL) INSTALLATION PG 15

PALP DOOR SQUEEZE (OPTIONAL) PG 16

WARRANTY PG 17

2

SAFETY

Watch for this symbol. It points out important safety precautions. It means “Attention – Be Alert!”

DEFINITIONS: CAUTION: Indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.

WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.

DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.

If any decals become damaged, detached, or illegible contact your dealer or Hi Qual at (844)-544-7825 for free replacements.

A careful operator, is the best operator. To help prevent accidents, read the following precautions before operating this equipment. Equipment should be operated only by those who are responsible and knowledgeable of this type of equipment.

Carefully review the procedures given in this manual with all operators. It is important that all operators be familiar with and follow safety precautions. Improper use of equipment can cause serious injury or death.

1. Read the operator's manual before operating equipment.

2. Keep hands, arms, feet, and legs away from all pinch points.

3. DO NOT remove any safety devices that have been provided for your protection.

4. DO NOT work around the equipment in loose clothing that might catch in any moving parts.

5. DO NOT modify the equipment without consulting a dealer or Sioux Steel Co.

6. Do NOT clean, lubricate, or adjust equipment, while equipment is operating.

7. Inspect the equipment regularly for any damage before and after each use. If damage to equipment occurs, equipment should not be used until repairs are made. Immediately, contact your dealer or Hi Qual Warranty Department at (844) 544-7825. Repair of damages should be implemented as soon as practical, with appropriate Hi Qual replacement parts.

REMEMBER: Hi Qual includes all reasonable means for accident prevention except a safe and careful operator.

3

REPAIR/REPLACEMENT PARTS LISTNotes:- The Hi Qual Squeeze Chute has been completely assembled at the factory.

- Before operating, install Ratchet Lock and Rope per customer preference. RatchetLock and Rope can be installed on either side of chute. See Ratchet Lock and Ropeinstallation sections of manual for additional details.

- Before operating, apply grease to grease zerks. Oil all other hinged and moving parts.

- Grease and oil as needed.

WARNING!KEEP HANDS AND FINGERS AWAY FROM ALL HINGED

AND MOVING PARTS DURING OPERATION.

ITEM NO. PART NUMBER DESCRIPTION QTY.

1 202699 FRAME ASSY- SQUEEZE CHUTE 1

2 191386LH LARGE DOOR- LH 1

3 189776 PIVOT WLDT - SM 2

4 191386RH LARGE DOOR RH 1

5 189724 DOOR - PALP LH 1

6 189724RH DOOR- PALP RH 1

7 191399 RATCHET ASSEMBLY 1

8 191398 RATCHET- LOCK HANDLE ASSY 1

9 191433W DOOR ASSY- SLICK DOOR 1

10 197610 PALP DOOR SQUEEZE 1

11 191527W PUSH BAR 1

12 208454 SERIAL NUMBER DECAL 1

13 208462 SHELBY FLOOR PLANK - 29.75 14

14 202559Thread-Forming Screw for Wood to Metal, 1/4"-

20, 2-1/2" Long56

15 191535 HANDLE GRIP 1.0" SQ 2

16 159781 NUT- .375 HEX -16 ELASTIC LOCK GR5 ZP 4

17 189708 HANDLE WLDT- PALP DOOR 1

18 203679 DECAL - HI QUAL 2

19 189708LH HANDLE WLDT- PALP DOOR/LH 1

20 176756 WASHER- .750 STD/TYPE B-SERIES SAE BZ 2

21 154066 FLATWASHER - 3/8" WIDE SERIES 10

22 191524 BLINDER 30X10 2

23 196474 2 X 3 PLASTIC TUBE PLUG 6

24 198836 ZERK- 1/4"-28 strght-short thrds 38

25 195827 WARNING DECAL "PINCH POINT" 3


27 189738 STOP PLATE- BUTT BAR 10

28 191529 HANDLE GRIP 1.25 SQ 6

29 191525 SMALL BLINDER 12

30 166543 NUT- .625 HEX-11 ELASTIC LOCK GR5 ZP 1

31 196459 SCREW- .625 HHC-11 X 3.5 GR5 ZP 1

32 154071 WASHER- .625 STD FLAT ZP 2

33 189515 NYLOCK NUT- 1/2-13 20

34 154069 WASHER - .500 FLAT TYPE A/W SERIES BZ 26

35 190006 SCREW- .50 HHC X 3.5 14

REPAIR/REPLACEMENT PARTS LIST


1 202699 FRAME ASSY- SQUEEZE CHUTE 1

2 191386LH LARGE DOOR- LH 1

3 189776 PIVOT WLDT - SM 2

4 191386RH LARGE DOOR RH 1

5 189724 DOOR - PALP LH 1

6 189724RH DOOR- PALP RH 1

7 191399 RATCHET ASSEMBLY 1

8 191398 RATCHET- LOCK HANDLE ASSY 1

9 191433W DOOR ASSY- SLICK DOOR 1

10 197610 PALP DOOR SQUEEZE 1

11 191527W PUSH BAR 1

12 195367 SERIAL NUMBER DECAL 1

13 202560 SHELBY FLOOR PLANK - 29.875 14

14 202559 Thread-Forming Screw for Wood to Metal, 1/4"-20, 2-1/2" Long 56

15 191535 HANDLE GRIP 1.0" SQ 2


17 189708 HANDLE WLDT- PALP DOOR 1

18 173803 DECAL - "SIOUX" OVAL 4.13" x 7" 2

19 189708LH HANDLE WLDT- PALP DOOR/LH 1

20 176756 WASHER- .750 STD/TYPE B-SERIES SAE BZ 2

21 154066 FLATWASHER - 3/8" WIDE SERIES 10

22 191524 BLINDER 30X10 2

23 196474 2 X 3 PLASTIC TUBE PLUG 6

24 198836 ZERK- 1/4"-28 strght-short thrds 38



27 189738 STOP PLATE- BUTT BAR 10

28 191529 HANDLE GRIP 1.25 SQ 6

29 191525 SMALL BLINDER 12


31 196459 SCREW- .625 HHC-11 X 3.5 GR5 ZP 1

32 154071 WASHER- .625 STD FLAT ZP 2

33 189515 NYLOCK NUT- 1/2-13 20


35 190006 SCREW- .50 HHC X 3.5 14


36 158981 SCREW-.500 HHC -13 X 7.50 GR5 ZP 2

37 191536 SPRING- DIE 4.0 X .5 2

38 191546 CAP- PLAS HNDL 1.315RNDX5"/BLK 1

39 203677 DECAL- HI QUAL 2

40 191545 HANDLE CAP 2

41 191495 HANDLE WELDMENT 2

42 191419W LINK WELDMENT 1

43 198409 PIVOT BUSHING 2

44 154051 NUT - 3/8-16UNC GR5 ZP 2

45 169367 WASHER 7/16" TYPE A/W SERIES ZP 14

46 169365 7/16-14 X 2 HEX HD CAPSCREW 2

47 191566 7/16" NYLOCK LOCK NUT 12

48 169366 7/16-14 X 1 1/2 HEX HD CAPSCREW 10

49 201464 TURNED EYE BOLT; 3/8-16 X 7.5 1

50 191557 SPRING- EXT. 7/8 X 4 1

51 169703 COTTER PIN - 5/32" x 1" ZP 4

52 176082 7/16"HEX IDx1.63"x0.8" ROLLER BEARING 4

53 189779 SPACER TUBE- BEARING 2

54 176081 1/2" RUE COTTER PIN RING 2

55 191622 Stop Pin Wldt 1

56 191767 HAIR PIN COTTER 0.148 X 3.3125 1

57 201402 Pulley, 3.5" OD, .5" ID, Fenner Drives 1

58 196552 UPPER PIVOT ASSY 2

59 191750 SCREW- .50 HHC X 4.5 1

60 191462 Spring- Compression 2.75 OD x 6.25 1

61 191537 HANDLE CAP .750 6

62 191556 SWIVEL EYE PULLEY 2

63 191562 PULL ROPE HANDLE 1

64 191565 RATCHET HANDLE SPACER 2

65 173991 PLUG- BLACK 2.0 SQUARE 8

66 191463 SPRING- EXTENSION 1.50 X 8.50 1

67 196490 SCREW- SELF DRILLING 1/4-14 X 1.0 ZP 52

68 196489 WASHER- .250 FENDER 1.00 OD 52

69 197654 ROPE- 7/16 SOLID BRAID NYLON 12FT

70 198400 OR 202800 HEAD GATE- AUTO OR MANUAL (OPTIONAL) 1

71 198610 CHAIN STOP ASSEMBLY 1

72 198606 ANCHOR TUBE WLDT 2

73 198895 DECAL- STRAP HERE 4

74 198664 PULLEY GUARD 1

75 201401 PULLEY SPACER 1

76 169707 SCREW- 3/8" -16 HHC X 2.25" 2

77 201457 FOOT PEDAL 2

5

OPTIONALPALP DOOR SQUEEZE

(NOT SHOWN)SEE NOTES BELOW

10

RH PALP DOORASSEMBLYFIGURE G

ROPE(NOT SHOWN)

SEE NOTES BELOW69

RH LARGE DOORASSEMBLYFIGURE D

OPTIONALAUTO OR MANUAL

HEAD GATE(NOT SHOWN)

SEE NOTES BELOW70

LH LARGE DOORASSEMBLYFIGURE C

LH PALP DOORASSEMBLY

FIGURE F

MAIN FRAMEASSEMBLY

FIGURE B SLICK DOORASSEMBLY

FIGURE E

71

NOTES: - SEE HEAD GATE INSTALLATION SECTION FOR ADDITIONAL DETAILS ON AUTO OR MANUAL HEAD GATE.- SEE ROPE INSTALLATION SECTION FOR ADDITIONAL DETAILS ON ROPE.- SEE PALP SQUEEZE SECTION FOR ADDITIONAL DETAILS ON PALP SQUEEZE.

FIGURE AMAIN ASSEMLBY BREAK DOWN

6

A

C

23

11

62

12

58

35 34 33

35 34 33

23 3

71

31 32 32 30

62

35 34 33

63

58

8

73

73

1314X

1456X

38

1

DETAIL A SCALE 1 : 10

35 34 33

323

50

593464643433

35 34 33

25

243433

61

60

26

DETAIL C SCALE 1 : 10

36 34 37 34 34 33

FIGURE BMAIN FRAME ASSEMBLY ITEM NO. PART NUMBER DESCRIPTION MAIN FRAME FIG

B/QTY.1 202699 FRAME ASSY- SQUEEZE CHUTE 13 189776 PIVOT WLDT - SM 27 191399 RATCHET ASSEMBLY 18 191398 RATCHET LOCK ASSY 111 191527W PUSH BAR 112 195367 SERIAL NUMBER DECAL 113 202560 SHELBY FLOOR PLANK - 29.875 14

14 202559 Thread-Forming Screw for Wood to Metal, 1/4"-20, 2-1/2" Long 56

23 196474 2 X 3 PLASTIC TUBE PLUG 625 195827 WARNING DECAL "PINCH POINT" 126 195828 WARNING DECAL "PINCH POINT" 231 196459 SCREW- .625 HHC-11 X 3.5 GR5 ZP 132 154071 WASHER- .625 STD FLAT ZP 233 189515 NUT- .500 HEX-13 ELASTIC LOCK GR5

ZP 17



35 190006 SCREW- .50 HHC X 3.5 1236 158981 HEX BOLT- 1/2-13 UNS X 7.500 G5 237 191536 SPRING- DIE 4.0 X .5 258 196552 UPPER PIVOT ASSY 159 191750 SCREW- .50 HHC X 4.5 160 191462 Spring- Compression 2.75 OD x 6.25 161 191537 HANDLE CAP .750 262 191556 SWIVEL EYE PULLEY 263 191562 PULL ROPE HANDLE 164 191565 RATCHET HANDLE SPACER 250 191557 SPRING- EXT. 7/8 X 4 171 198610 CHAIN STOP ASSEMBLY 130 198895 DECAL- STRAP HERE 424 198836 ZERK- 1/4"-28 strght-short thrds 2

7

2

28

29

25

24

22

24

61

24

65

72

48 27 45 47

67 68

6867

24

7716

76

FIGURE CLH LARGE DOOR ASSEMBLY

ITEM NO. PART NUMBER DESCRIPTION FIG C LH DOOR ASSY/QTY.

22 191524 BLINDER 30X10 125 195827 WARNING DECAL "PINCH POINT" 126 195828 WARNING DECAL "PINCH POINT" 127 189738 STOP PLATE- BUTT BAR 528 191529 HANDLE GRIP 1.25 SQ 329 191525 SMALL BLINDER 647 191566 7/16" NYLOCK LOCK NUT 561 191537 HANDLE CAP .750 265 173991 PLUG - 2" SQUARE 268 196489 WASHER- .250 FENDER 1.00 OD 2672 198606 ANCHOR TUBE WLDT 145 169367 FLATWASHER - 7/16" 524 198836 ZERK- 1/4"-28 strght-short thrds 122 191386LH LARGE DOOR- LH 148 169366 SCREW-.438 HHC -14 X 1.50 GR5 567 90064A620 SCREW- SELF DRILLING 1/4-14 X 1.0

ZP 26


76 169707 SCREW- 3/8" -16 HHC X 2.25" 1


8

4

29

28

65

24

72

67 68

47 45 27 48

67 68

22

61

61 77

76

16

FIGURE DRH LARGE DOOR ASSEMBLY

ITEM NO. PART NUMBER DESCRIPTION FIG D RH DOOR ASSY/QTY.

22 191524 BLINDER 30X10 125 195827 WARNING DECAL "PINCH POINT" 127 189738 STOP PLATE- BUTT BAR 528 191529 HANDLE GRIP 1.25 SQ 329 191525 SMALL BLINDER 647 191566 7/16" NYLOCK LOCK NUT 526 195828 WARNING DECAL "PINCH POINT" 161 191537 HANDLE CAP .750 265 173991 PLUG - 2" SQUARE 268 196489 WASHER- .250 FENDER 1.00 OD 4372 198606 ANCHOR TUBE WLDT 145 169367 FLATWASHER - 7/16" 524 198836 ZERK- 1/4"-28 strght-short thrds 124 191386RH LARGE DOOR RH 148 169366 SCREW-.438 HHC -14 X 1.50 GR5 567 90064A620 SCREW- SELF DRILLING 1/4-14 X 1.0

ZP 43


76 169707 SCREW- 3/8" -16 HHC X 2.25" 1


9

55

5666

4449 21

44

46 45 43 45 47

4645434547

65

65

35 34 34 33

35343433

52545352

33 74 57 75

24

2451

40

41

39

26

41

40

24

51

9

FIGURE ESLICK DOOR ASSEMBLY

ITEM NO. PART NUMBER DESCRIPTION FIG E SLICK DOOR ASSY/QTY.

9 191433W DOOR ASSY- SLICK DOOR 121 154066 FLATWASHER - 3/8" WIDE SERIES 226 195828 WARNING DECAL "PINCH POINT" 233 189515 NYLOCK NUT- 1/2-13 3


35 190006 SCREW- .50 HHC X 3.5 239 187321 DECAL- SIOUX OVAL 2.63 X 4.87 240 191545 HANDLE CAP 241 191495 HANDLE WELDMENT 242 191419W LINK WELDMENT 144 154051 NUT - 3/8-16UNC GR5 ZP 247 191566 7/16" NYLOCK LOCK NUT 251 169703 COTTER PIN - 1/8" x 1" ZP 252 176082 7/16"HEX IDx1.63"x0.8" ROLLER

BEARING 453 189779 SPACER TUBE- BEARING 254 176081 1/2" RUE COTTER PIN RING 255 191622 Stop Pin Wldt 156 191767 HAIR PIN COTTER 0.148 X 3.3125 165 173991 PLUG - 2" SQUARE 466 191463 SPRING- EXTENSION 1.50 X 8.50 145 169367 FLATWASHER - 7/16" 457 201402 Pulley, 3.5" OD, .5" ID, Fenner Drives 174 198664 PULLEY GUARD 175 201401 PULLEY SPACER 143 198409 PIVOT BUSHING 249 201464 TURNED EYE BOLT; 3/8-16 X 7.5 124 198836 ZERK- 1/4"-28 strght-short thrds 846 169365 SCREW-.438 HHC -14 X 2.00 GR5 ZP 2

10

5

15

18 17

51

16

21

20

LH PALP DOOR ASSEMBLYFIGURE F

11

6

51

18

21

16

19

20

15

RH PALP DOOR ASSEMBLYFIGURE G

12

6464 34

8

60

DETAIL D

SCALE 1 : 8

3459 33

FIGURE H

SIDE OF CHUTE

BE INSTALLED ON EITHER

RATCHET LOCK CAN

D

RATCHET LOCK INSTALLATION

13

ONTO SLICK DOOR

DROP PULLEY

LINK CONTROL ARM

AT DESIRED LOCATION,PASS ROPE THRU PULLEY,AND TIE TO PULL ROPEHANDLE ITEM 63

PASS ROPEAROUND PULLEY

HOOK DROP PULLEY

PASS ROPE THRU

TIE END OF ROPE

ROPE

ITEM 69

PASS ROPE THRU PULLEY,

AROUND PULLEY

HOOK DROP PULLEYAT DESIRED LOCATION,

AND TIE TO PULL ROPEHANDLE ITEM 63

ONTO SLICK DOORLINK CONTROL ARM

PASS ROPE

TIE END OF ROPE

PASS ROPE THRUDROP PULLEY

ROPE

ITEM 69

NOTE: ROPE CAN BE INSTALLED ON EITHER SIDE OF CHUTE AS SHOWN BELOW.

ROPE INSTALLATION

FIGURE I

FIGURE J

14

INSTALL ONTOFRAME AS

SHOWN

S198400AUTO HEAD GATE

FIGURE K

S194538 OR S198620MANUAL HEAD GATE

FIGURE M

ATTACH HEAD GATE TO MAIN FRAME AS SHOWN

FIGURE L

AUTO & MANUAL HEAD GATE (OPTIONAL) INSTALLATION

36

SCALE 1 : 12

DETAIL H

CHAIN

34 37 34 34 33

SAFETY

CHAIN HEREATTACH SAFETY

33 34

15

PALP DOOR SQUEEZE (OPTIONAL)

FIGURE O

FIGURE NS197610- PALP DOOR SQUEEZE (ITEM 10)

PALP DOORPALP DOOR SQUEEZECAN BE INSTALLED ONEITHER LH OR RH PALPDOORS

16

{00659155.1}

NEW PRODUCT WARRANTY HIQUAL LIVESTOCK EQUIPMENT

LIMITED WARRANTY FOR NEW HIQUAL COMPANY PRODUCTS A. GENERAL PROVISIONS . “HiQual” means HiQual Company, 200 N. Cleveland, Lennox, SD 57039. The warranties described below are provided by HiQual to the original purchasers of new products purchased from HiQual or from an authorized HiQual Dealer (the “Products”). Under these warranties, HiQual will, at its option, repair or replace at its factory any Product covered under these warranties which is found to be defective in material and workmanship during the applicable warranty term or refund the purchase price paid for the defective Product. Customer will be responsible for labor charges for removing the defective Product and reinstalling the repaired or replacement Product, any premium charge for overtime labor requested of HiQual and shipping charges to and from HiQual’s factory. These warranties are not transferrable.

B. WARRANTY PERIOD . Subject to exclusions and limitations set forth herein, each new Product is warranted for the number of years specified below. Each warranty term begins from the date of purchase regardless of delay in receipt of the Product by Customer due to the time required to process, handle, ship, assemble, construct and install the Product. Customer must retain proof of the date of purchase. Replacement parts for and repairs to the Product will be warranted only for the remainder of the original warranty term. The replacement parts for or repairs to the Product will not extend the warranty term beyond the original warranty term. Products described below include all parts, components and accessories.

PRODUCTS All Steel products 1 Year All Poly Products 3 years Flex Connectors 5 Years C. ITEMS COVERED SEPARATELY . The HiQual warranties do not cover any parts, components or materials that are part of the Product, or used in conjunction with the Product, that are not manufactured by Sioux Steel. Such parts, components and materials will be subject to the warranties provided by the manufacturer, if any. D. WHAT IS NOT WARRANTED . HiQual does not warrant and is not responsible for the following: (1) used products; (2) modification or alteration of the Products; (3) Products that have not been properly installed or not installed in accordance with the instruction manual, improper assembly, or improper construction by any persons other than HiQual employees; (4) depreciation, damage or loss caused by the use of parts, components or accessories not provided by HiQual, unauthorized repairs, normal wear, lack of necessary and proper maintenance, a failure to follow operating instructions/recommendations, misuse, lack of proper protection during storage, vandalism or theft, exposure to the elements or corrosive materials, accidents or acts of nature including lightning, flooding, hail, straight winds and tornadoes; and (5) cosmetic damage or damage that does not hinder the functionality of the Products. E. LIMITATIONS OF WARRANTIES AND CUSTOMER’S REMEDIES . To the extent permitted by law, neither HiQual, the Dealer nor any person or company affiliated with either of them makes any warranties, representations, conditions or promises express or implied as to the quality, performance or freedom from defects of the Products covered by these warranties other than those set forth herein. THERE ARE NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. NEITHER HIQUAL, THE DEALER, NOR ANY PERSON OR COMPANY AFFILIATED WITH EITHER OF THEM WILL BE LIABLE FOR ANY DAMAGES, INCLUDING, BUT NOT LIMITED TO, INCIDENTAL, SPECIAL, EXEMPLARY, CONSEQUENTIAL, LOST PROFITS AND REVENUES, LOST USE OF THE PRODUCTS OR ANY OTHER PROPERTY, BODILY INJURY OR PROPERTY DAMAGE CLAIMS OF ANY PERSON, LOST COMMODITIES, REMOVAL OR STORAGE COSTS FOR THE PRODUCTS, OTHER EQUIPMENT AND COMMODITIES, DAMAGE TO THE ENVIRONMENT ARISING FROM OR IN ANY MANNER RELATED TO ANY RELEASE OF HAZARDOUS MATERIALS, AND REMEDIATION EXPENSES THEREFORE, WHETHER BASED ON CONTRACT, TORT, STRICT LIABILITY OR ANY OTHER LEGAL BASIS, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO INSTANCE WILL SIOUX STEEL, THE DEALER OR ANY PERSON OR COMPANY AFFILIATED WITH EITHER OF THEM BE LIABLE TO CUSTOMER OR ANY PERSON IN AN AMOUNT IN EXCESS OF THE PURCHASE PRICE PAID BY CUSTOMER FOR THE PRODUCT. F. NO DEALER WARRANTY . THE DEALER HAS NO AUTHORITY TO MAKE ANY WARRANTY, REPRESENTATION, CONDITION OR PROMISE ON BEHALF OF HIQUAL, OR TO MODIFY THE TERMS OR LIMITATIONS OF THIS WARRANTY IN ANY WAY. G. GOVERNING LAW/VENUE . These warranties, and all terms set forth herein, are governed by the laws of the State of South Dakota and, where applicable, the laws of the United States of America. Any and all disputes arising from these warranties, the purchase and use of the Products, bodily injury and property damage claims or otherwise must be venued in the South Dakota Circuit Court sitting in Minnehaha County, South Dakota. Customer agrees to such venue and waives any challenge to such court’s jurisdiction based upon lack of personal jurisdiction or inconvenience. H. SECURING WARRANTY SERVICE. In order to receive warranty services, customer must give HiQual written notice of a warranty claim within 30 days of the date of discovery of the defective materials or workmanship, and customer must complete the following steps. (1) Obtain from HiQual a Return Materials Authorization Number (“RMA Number”) by calling the Customer Service at 1 -800-557-4689 and providing the following information.

� An explanation as to why the products being returned.

� The name of the territory representative, dealer or HiQual sales person from whom the product was purchased.

� The dealers ID number / account number.

� The invoice number and date of purchase.

� Customers name, phone number and address.

� The date the product will be returned.

(2) Pay the shipping charges to and from the HIQual’s factory.

(3) Ship the product to HiQual, 200 N. Cleveland, Lennox, SD 57039

squeeze chute #191440 - hiqual equipment chute.pdf · do not modify the equipment without...

Documents