specifications vespa

8/6/2019 Specifications Vespa

1/5

Specifications

If you are in the market for a scooter, the P200 is a good choice. It is a well designed "classic"

scooter with power to spare. Many people complain about the angularity of the P-Series, but theyare still very waspy. The front mudgard and cowls are what give the "P" it's look. I think it reallysuits an electronic music lifestyle (reminds me of the old JX-3P synth in my room). Anyway, I

find the specifications give a good insight into the workings of this infamous series. Whatfollows is a list of specifications for the Vespa P200 under ideal conditions.(1)

Quick Index: Physical : Engine & Transmission : Fuel System : Brakes & Wheels : Electrical :

Wrench Settings

Physical Specs

Overall Length: 1760 mm (69.3 in)Overall Width: 695 mm (27.3 in)Overall Height: 1110 mm (43.7 in)Wheelbase: 123 5mm (48.7 in)Ground Clearance: 225 mm (8.9 in)Dry Weight: 108 kg (238 lb)Chassis No. Prefix: VSX 1 TEngine No. Prefix: VSE 1 MTypical Speeds:Top: 120 kph (75 mph)Cruise: 104 kph (65 mph)

Engine & Transmission Specs

EngineType: Single cylinder fan-cooled two strokeBore: 66.5 mm (2.618 in)Stroke: 57.0 mm (2.240 in)Displacement: 197.97cc (12.080 cu in.)Compression: 9.8:1

CylinderType: Cast Aluminum Alloy

Cylinder BarrelType: Cast IronBore Sizes: 66.5 mm (2.618 in)1st Oversize: 66.7 mm (2.626 in)2nd Oversize: 66.9 mm (2.634 in)3rd Oversize: 67.1 mm (2.642 in)

Piston


2/5

Standard Diamter: 66.292 mm (2.6099 in)Oversizes: 3, in 0.2 mm (0.0079 in increments)Ring free end gap: 0.025-0.040 mm (0.010-0.016 in)

Crankshaft AssemblyMax. Runout

At mainshaft ends: 0.03mm (0.0012 in)At flywheel faces: 0.02mm (0.0079 in)

ClutchType: Wet, MultiplateNo. of Friction Plates: 3No. of Plain Plates: 2

GearboxType: 4 speed constant meshRatios:1st Gear: 14.47:12nd Gear: 10.28:1

3rd Gear: 7.31:14th Gear: 5.36:1

Fuel System & Lubrication

CarburettorMake: Dell'Orto [sic]Type: SI24/24E (older models may have an SI20/20D)Venturi Size: 24 mm (0.95 in)

JetsMain: 116Diffuser: BE3

Atomizer: 60Idle SS: 160Starter Jet: 60

Air FilterType: Pleated Fabric and Gauze

Engine LubeType: Premix or InjectionPre-Mix Oil Ratio: 50:1 (2%)

Two Stroke Oil: Good Quality [ash free] 2 Stroke Oil (Synthetic or Natural)

Gearbox LubeOil Grade: [Non-Detergent] SAE 30 motor oilCapacity: Holding the bike straight up and down, the oil will drip

from the filler hole when full. (approx. 250mL 8.5oz)

Physical Fuel Line Lengthlength: 2 feet


3/5

Wheels Brakes and Tires

WheelsType: Pressed steel split rims, spare wheel available as option. Wheels

are interchangeableSize: 2.10 X 10

BrakesType: Internal expanding drum brakes, single leading shoe (SLS) type, front

and rear.

Tires

Size: 3.50 X 10, front and rearPressure (for factory tires)Front: 17.6 psi (1.23 kg/cm2)Rear (up to 180 pound load): 25.8 psi (1.8 kg/cm2)Rear (over 180 pound load): 36.7 psi (2.58 kg/cm2)

Electrical System

SystemType: 12VAC with electronic AC regulation

Some bikes are fitted with batteries for DOT safety equipment.(such as Turn Signals, Horn, Tail and Brake Lights)

Alternator: Ducati "Star" configuration @ 12 VoltsRegulator: Electronic AC typeHorn: Electromagnetic, 12VAC for non battery bikes

Electromagnetic or Resonant Disc, 12VDC for battery bikes

12 Volt BulbsHeadlamp: 25/25W (some bikes may have a sealed beam. Replace with equivalent)


4/5

Tail Lamp: 5W/10W combination lampStop Lamp: 5W/10W combination lampSpeedometer Lamp: (no. 1816) 12 Volt 3W bulb. (Canadian Tire No. 20-3064-2)Warning Lamps: 2W

Spark Plug

Normal Conditions: NGK B7ES or equivalentHighway Conditions: NGK B8ES or equivalent

BatteryType: 12V 9 Amp Hours (Ah)Specific Gravity: 1.260 to 1.280Chemical Makeup: Lead Acid

FuseType: 8 amp (european style)

CDI UnitType: Proprietary Sealed 'black box' Unit

Spark Plug interconnection: Silicone coated Oxygen Free Cable (18 Guage inner)Almost any car spark plug wire will work as long asthe wire length is correct.

TorqueWrench Settings

Standard SettingsBOLTS5mm bolt or nut: 0.45-0.6 kgf m (3.5-4.5 lbf ft)6mm bolt or nut: 0.8-1.2 kgf m (6-9 lbf ft)8mm bolt or nut: 1.8-2.5 kgf m (13-18 lbf ft)

10mm bolt or nut: 3.0-4.0 kgf m (22-29 lbf ft)12mm bolt or nut: 5.0-6.0 kgf m (36-43 lbf ft)

SCREWS5mm screw: 0.35-0.5 kgf m (2.5-3.6 lbf ft)6mm screw: 0.7-1.1 kgf m (5-8 lbf ft)

FLANGE BOLTS6mm flange bolt: 1.0-1.4 kgf m (7-10 lbf ft)8mm flange bolt: 2.4-3.0 kgf m (17-22 lbf ft)10mm flange bolt: 3.0-4.0 kgf m (22-29 lbf ft)

Engine & Tranny Settings

Stator Screws: 0.3-0.4 kgf m (2.17-2.89 lbf ft)Kickstart Lever Nut: 2.3-2.6 kgf m (16.64-18.81 lbf ft)Coil Pickup mounting screws: 0.2-0.25 kgf m (1.45-1.81 lbf ft)Clutch Center Nut: 4.0-4.5 kgf m (28.93-32.55 lbf ft)Input Shat Nut: 3.5-3.5 kgf m (21.70-25.32 lbf ft)Rotor Nut: 6.0-6.5 kgf m (43.40-47.01 lbf ft)Carb Sleeve Nuts: 1.6-2.0 kgf m (11.57-14.47 lbf ft)Clutch Cover Bolts: 0.6-0.8 kgf m (4.34-5.79 lbf ft)Cylinder Head Nuts: 1.7-2.2 kgf m (12.30-15.91 lbf ft)


5/5

Exhaust Pipe Stub: 7.5-8.0 kgf m (54.25-57.86 lbf ft)

Frame & Suspension SettingsSuspension unit mounting plate nuts: 2.0-2.7 kgf m (14.5-19.5 lbf ft)Suspension unit to mounting plate nut: 3.0-4.0 kgf m (21.7-28.9 lbf ft)Suspension unit lower mounting nuts: 2.0-2.7 kgf m (14.5-19.5 lbf ft)

Steering head adjuster (preload): 0.6-0.7 kgf m (4.34-5.06 lbf ft)Steering head locknut: 5.0-6.0 kgf m (36.2-43.4 lbf ft)Handlebar pinch bolt: 3.0-4.4 kgf m (21.7-28.9 lbf ft)Rear suspension unit lower mounting bolt: 1.3-2.3 kgf m (9.4-16.6 lbf ft)Engine unit pivot unit: 6.1-7.5 kgf m (44.1-54.3 lbf ft)Front wheel hub nut: 7.0-10.0 kgf m (43.4-72.3 lbf ft)Rear wheel hub nut: 7.5-9.0 kgf m (54.3-65.1 lbf ft)Wheel mounting nuts: 2.0-2.7 kgf m (14.5-19.5 lbf ft)

specifications vespa

Documents