socata tbm850 g1000 config mode screens this guide will allow a service center to determine if...
TRANSCRIPT
Socata TBM850 G1000 Config Mode Screens
This guide will allow a Service Center to determine if unauthorized changes have been made in G1000 Configuration screens for the TBM850. If the G1000 system software version is 0719.01, and the screens do not match these
shown, unauthorized changes may have been made. Contact Garmin Product Support for assistance if needed to reset the G1000 system.
This presentation is for reference only and does not replace any approved G1000 Service Literature instructions.
System Group Pages No changes can be made to this page.
System Group Pages No changes can be made to this page.
System Group Pages Changes can be made.Reload PFD 1 Config file to reset.
System Group Pages Changes can be made.Reload MFD 1 Config file to reset.
System Group Pages Changes can be made.Reload PFD 2 Config file to reset.
System Group PagesChanges can be made.
Reload GCU Config file and then “Update CFG” to reload Master Config Module to reset.
System Group PagesChanges can be made.
Reload GMC Config file and then “Update CFG” to reload Master Config Module to reset.
System Group PagesAudio Test box changes are not saved. Changes
can be made in the Altitude Alerter box. Reload AIRFRAME config file to reset.
System Group PagesOptional equipment (ADF, DME, ChartView, TAWS,
etc.) can be disabled by reloading certain config files. Reload per G1000 LMM to correct.
System Group PagesGIA and GFC Servo Fault logs can be
deleted. Old Data can not be recovered after deletion.
System Group Pages No changes can be made to this page.
System Group Pages No changes can be made to this page.
System Group Pages GDL69 & GWX can be turned on/off here. Reload SYSTEM config file to reset.
System Group Pages No changes can be made to this page.
System Group Pages No changes can be made to this page.
System Group Pages No changes can be made to this page.
System Group Pages No changes can be made to this page.
System Group Pages No changes can be made to this page.
System Group Pages Changes can be made.Clear User Settings to reset.
System Group Pages No changes can be made to this page.
GDU Group Pages Changes can be made.Reload MFD 1 Config file to reset.
GDU Group Pages Changes can be made.Reload PFD 1 Config file to reset.
GDU Group Pages Changes can be made.Reload PFD 2 Config file to reset.
GDU Group Pages Changes can be made.Reload PFD 1, PFD 2 & MFD 1 Config files to reset.
GDU Group Pages Changes will not be saved in this page.
GDU Group Pages No changes can be made to this page.
GDU Group Pages No changes can be made to this page.
GDU Group Pages Changes will not be saved in this page.
GDU Group Pages Changes will not be saved in this page.
GDU Group Pages Changes will not be saved in this page.
GDU Group Pages Changes will not be saved in this page.
GDU Group Pages Changes will not be saved in this page.
GDU Group Pages Changes will not be saved in this page.
GDU Group Pages Changes will not be saved in this page.
GDU Group Pages No changes can be made to this page.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module. “CLR NV” softkey use will require GIA, Audio and GFC Cert Config files to be reloaded.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module. “CLR NV” softkey use will
require GIA, Audio and GFC Cert Config files to be reloaded.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GIA Group PagesChanges can be made.
If COM no longer functions after incorrectly adjustingthese values, the GIA must be replaced.
After tuning to each desired calibration frequency, the current GIA unit must be selected again to force an update of the
calibration data values. The data values can then be changed appropriately to continue the desired procedure.
***Note***Only the frequencies 118.00, 127.00, & 136.975 may be used
when setting squelch and sidetone levels.
GIA Group Pages No changes can be made to this page.
GIA Group Pages No changes can be made to this page.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GIA Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page.
GEA Group Pages No changes can be made to this page without an unlock key press sequence.
GTX Group PagesChanges can be made.
Reload GTX 1 Config file and then “Update CFG” to reload Master Config Module to reset.
GTX Group PagesChanges can be made.
Reload GTX 2 Config file and then “Update CFG” to reload Master Config Module to reset.
GTX Group PagesChanges can be made. Reload GTX 1 Config file and then “Update CFG”
to reload Master Config Module to reset. Then verify Address Type, Address, Flight ID Type and Flight ID are correct.
GTX Group PagesChanges can be made. Reload GTX 2 Config file and then “Update CFG”
to reload Master Config Module to reset. Then verify Address Type, Address, Flight ID Type and Flight ID are correct.
GRS Group Pages No changes can be made to this page.
GRS Group Pages No changes can be made to this page without an unlock key press sequence.
GDC Group Pages No changes can be made to this page.
GDC Group Pages No changes can be made to this page.
GFC Group PagesChanges can be made. Reload the following config files: GIA 1, Selected Alt option, KTA810 (if equipped) and then “Update CFG” to reload Master
Config Module.
GFC Group PagesChanges can be made. Reload the following config files: GIA 2, Selected Alt
option, and if equipped the WX500, KTA810, KRA405, KN63 and ADF; then “Update CFG” to reload Master Config Module.
GFC Group Pages If “RST GAIN” softkey is pressed, Pitch Cert file needs to be reloaded to restore AP ops.
GFC Group Pages If “RST GAIN” softkey is pressed, Roll Cert file needs to be reloaded to restore AP ops.
GFC Group Pages If “RST GAIN” softkey is pressed, Yaw Cert file needs to be reloaded to restore AP ops.
GFC Group Pages If “RST GAIN” softkey is pressed, Pitch Trim Cert file needs to be reloaded to restore AP ops.
GFC Group Pages If “RST GAIN” softkey is pressed, Yaw Trim Cert file needs to be reloaded to restore AP ops.
GMA Group PagesChanges can be made. Reload the following config files: GMA
1, and if equipped the KN63 and ADF; then “Update CFG” to reload Master Config Module.
GMA Group PagesChanges can be made. Reload the following config files: GMA
2, and if equipped the KN63 and ADF; then “Update CFG” to reload Master Config Module.
GMA Group PagesChanges can be made. Reload the following config files: GMA
1, and if equipped the KN63 and ADF; then “Update CFG” to reload Master Config Module.
GMA Group PagesChanges can be made. Reload the following config files: GMA
2, and if equipped the KN63 and ADF; then “Update CFG” to reload Master Config Module.
GDL Group Pages Ethernet Port changes can be made.Reload GDL Config file to reset.
RMT Group Pages No changes can be made to this page.
RMT Group Pages No changes can be made to this page.
GWX Group Pages Radar Pitch and Roll Trim Changes can be made. Reset Radar pitch and roll trim if needed.
CAL Group PagesFuel temp L&R Offset changes can be made, they
should be set to 0. No other changes can be made to this page without an unlock key press sequence.
CAL Group Pages No changes can be made to this page without an unlock key press sequence.
CAL Group Pages No changes can be made to this page without an unlock key press sequence.