Caution➀ Installer must make sure SMS CL V is positively and securely attached, and appropriate fasteners are used.➁ Before installing, check to make sure all parts of the mount are there.➂ Assembly hardware is included; mounting fi ttings are not included with the product for reasons of safety, since the properties and bearing strength of walls/ceilings are specifi c for each case. Suitable mounting fi ttings must be selected based on the material of the wall/ceiling. It is the responsibility of the installer to ensure that the wall/ceiling can support at least four times the combined weight of the screen/projector and bracket.➃ The maximum weight of a screen/projector to be used with the SMS CL V is 12 kg, or 26 lb.➄ Make sure all screws and bolts are tightened before allowing the mount to bear the full weight of the projector.➅ Mount projector before hooking up to electrical and other cables.➆ When making adjustments, make sure projector is fi rmly supported.➇ All assembly screws require Metric Allen wrench (included).

Tools/Hardware Required

Parts/Hardware Included

SMS CL V—Exploded View

SMS CL V—Mounting Plate

➀ Pre-assemble upper column (A) to celiing plate (B) using provided hardware.

➁ Use ceiling plate to mark mounting hole positions on ceiling.

➂ Drill mounting holes. ➃ Attach ceiling plate and upper column to ceiling.

Please Note: mounting fi ttings are not included with the product for reasons of safety, since the properties and bearing strength of walls/ceilings are specifi c for each case. Suitable mounting fi ttings must be selected based on the material of the wall/ceiling. It is the responsibility of the installer to ensure that the wall/ceiling can support at least four times the combined weight of the screen/projector and bracket.

Adjustment Some models of the CL V have several points of adjustment. For ranges of adjustment according to model, see charts below. Adjustments are infi nite within range. Adjustments can be made with the projector attached to the mount; built-in safety features will prevent accidents by “catching” the lower section before it drops out of the unit.

➂ On adjustable models, if appropriate, run wiring down through large slots in mounting plate.➃ Run wiring along cable guides for hookup to projector. Place cable covers in cable guides, then snap on side covers.

➄ Attach lower column cover.

Adjustable Mount DimensionsFixed Mount Dimensions

4

3/4" 7

1/2"11/2" 2

3/8"

A B

C

Model A (Min) B (Max) C CLV 300-350 133/8" 153/8" 2"

CLV 500-750 211/4" 311/8" 97/8"

CLV 650-900 271/4" 37" 97/8"

CLV 850-1100 351/8" 447/8" 97/8"

CLV 1050-1300 43" 527/8" 97/8"

Adjustability Pitch Roll YawAt Ceiling Plate ±30º 0º 0º

At Ball Joint ±30º ±30º 360º

33/8"

47/8"

3/16"

CL F 80

Low Profi le

Universal Projector Bracket Coverage

Dis

tanc

e be

twee

nce

iling

and

bot

tom

of m

ount

:31 /

8"

Dis

tanc

e be

twee

nce

iling

and

bot

tom

of U

nive

rsal

Pro

ject

or:

Bra

cket

: 6"

23/4"

Min. approx.

O 51 /2"

(140 mm)

Max. approx.

O 15"

(380 mm

)

37/8"

➁ Insert and adjust threaded pipe so that, when they are fl ush with the surface of the projector, the universal bracket is horizontally level.

A minimum of three mounting holes need to be used to securely attach the AeroUniversal Bracket to the projector.

Attaching Universal Mounting Bracket to Projector➀ Place the Universal Projector Mounting Bracket over projector mounting holes. If bracket arms cannot reach all mounting holes, loosen bracket by unscrewing centerpiece, and replacing bracket arms with longer size arms (included).Please Note: Open ends of bracket arms should be at least fl ush with the outer edge of the centerpiece; if open ends are not fl ush, use longer arms.

Please Note: Universal Bracket adds a minimum of 3" to overall height.

➂ Insert and tighten screws (provided) appropriate for projector mounting holes.Please Note: Do not overtighten screws into projector. If screw is hitting the end of the threaded hole, add more washers at the top of the screw.

➃ Adjust the centerpiece so that it is above the projector’s center of gravity, and tighten centerpiece. To determine the projector's center of gravity, place a small level on the projector. Hold the projector by the top of the bracket nut and make sure the projector hangs level. Adjust the Univer-sal Projector Bracket by sliding the centerpiece along the arms until the projector hangs level, then tighten the centerpiece.

➄ Tighten lower locking nut. ➅ Place the mount ball joint into the slot in the nut.

➉ Adjust height and tighten setscrews.➆ Tighten the nut.➇ Tighten the upper locking nut.➈ Rotate projector into position.