simpladent single piece sap en v036...1. have your laboratory produce a drilling template with the...

SYSTEM APPLICATIONSingle part implants

IMMEDIATE LOADING DENTAL IMPLANT SYSTEM

2

APPLICATION AND SURGERY

1. Have your laboratory produce a drilling template

with the appropriate drill holes for the marker bore. Use a

DOS 1 or BCD 1 (yellow) drill for pre-drilling.

Use the shaping drill to the implant bed to full length. Use

an intermittent drilling technique and copious

saline irrigation.

2. The laboratory might insert guide sleeves (BFH)

into the drill holes to ensure that the drilling angle

is exactly correct.

3. In hard bone, if the full drilling depth is difficult to

attain with DOS 1, use the DS 2 cylinder drill (2 mm)

to achieve the correct depth.

WST steel drill, 2 mm ø

Drill hole with

guide sleeve

Surgical guide

DOS 1 DS 2

Jaw

or possibly

DOS 2

Depth drill, black

BCD 2

black

DS 2

Pilot drill

DOS 2 / BCD 2

Determine the correct direction and depth; alternatively, use BCD 1 “pathfinder” drill.

DS 2 pilot drill

Use for hard bone, but only in the cortical area.

1. DRILLING AND PREPARING/CONDENSING THE IMPLANT BED

All KOC® implants are used as compression screws. In order to acchieve a good bone condensation and implant stability, the drilling should be carried out thinner

than the core diameter of the implant. The minimal diameter of the drill depends on the bone density. It is therefore not possible to advise drill-sequences which

fit all bone-qualities. Typically in the soft maxillary bone only small drill-diameters are used (e.g. the usage of DOS1 only, for implants with 3.0 - 5.0 mm diameter),

whereas in the highly mineralized lower jaw a specific drill sequence with respect to the mineralisation of the bone is necessary.

Original packaging Remove the barcode label

and place it in the patient file

Open the internal packaging

containing the implant and

implant holder

2. IMPLANT PACKAGING

PRELIMINARIES

3

3. REMOVE THE IMPLANT FROM ITS PACKAGING

1. The implant is attached to the holder and can be

broken off at a pre-determined breaking point.

2. Remove the implant using the plastic holder.

4. HANDLING

Hold implant at the carrier, and place the placement aid on

the implant head. Do not touch the

endosseous implant surface.Remove the implant complete

with the plug and then remove the plug

at the break line.

5. INSERTION USING MANUAL TOOLS

Manually insert the implant into the jaw until it is

seated firmly.

6. DEFINITIVE IMPLANT INSERTION

Use the ratchet, torque wrench or angled handpiece

to screw the implant into the implant bed (clockwise).

The enossal (sandblasted) aspect of the implant must

be completely submerged in the bone. The polished

implant neck must be at the level of the mucosa. It is

recommended to screw approximately an additional 1

mm of the implant neck into the bone.

7. REMOVING THE PLACEMENT AID FROM THE IMPLANT

SURGERY

KOC® implant with ITW K

placement aid (for angled

handpiece) and IT K (manual)

Removing the holder

IT K

KOC® Micro

implant

Jaw

KOC® Micro implant

Jaw

KOC® Micro implant

Jaw

Predetermined break line

ITW K

KOC® Micro

implant

Jaw

IT K

KOC® Micro implant

Jaw

4

8. RESULT

• All implant heads can be modified in shape using redary instruments.

• The implants can be immediately loaded prosthodontically if a

suitable indication exists.

• The definitive superstructure must be cemented within the

next few days.

• Immediate prosthetic splinting using a provisional bridge is

recommended.

9. IMPRESSION

Bridges

Slipping on the TSPA 4 impressionpost, internally round, for KOC®

Micro and KOC® TX

Crowns

Slipping on the TSKPA 4 impression post,

anti-redational, for KOC® Micro and KOC® TX

Impression taking with Safeprint® or Duraprint® Remove the individual tray from the implant. The

impression contains the impression post at this stage.

Forward the impression to the laboratory

LABORATORY PROCEDURES

Slipping the impression post onto lab analogues

Bridges

TSPA 4 on

IAK M / 13-462111

Single-Tooth

replacements

TSKPA 4 on

13-462111

Create a plaster cast

Remove the impression from the cast. The impression

post and lab analogue are now separated again.

IAK M / 13-462111 13-462111

Wax up on PO4 pre-shaped castings (internally round; for bridges and bar connectors) or PO4A pre-shaped castings (with

internal edges; for single crowns).

SURGERY

KOC® Micro implant

Jaw

Alternatively, the impression

can also be taken directly for

KOC® Micro and KOC® TX.

PO4 A PO4

Lab analogue

Fill with dental stone

5

KOC® IMPLANTS

The KOC® implant system is made of the highly fracture-resistant Ti6Al4V ELI

titanium alloy pursuant to ASTM F136. The implants are single-piece implants

with an apical compression thread and straight, flexible or angled solid abutment.

Suitable for crowns, bridges and bar connectors. The compression screw design

facilitates immediate prosthetic loading, provided surgical placement was carried

out correctly (restoration placed within three days or less). KOC® implants are today

routinely used for immediately loaded bridge structures. The single-piece design

saves expense and time and minimises the problem of screw loosening. KOC® und BE-

CES® are combined in cases of extraction.

hhiigghhllyy ffra

e implants

ht, flexible

ctors. The c

vided surgic

days or less)

e structures

blem of screw

issttaanntt TTii66AAl

gle-piece im

d solid abu

sion screw

ment was

mplants are

ngle-piece

ing. KOC® u

6

KOC® MULTIUNIT AND BECES® MULTIUNIT IMPLANTS

KOC® MU IMPLANTS

Description Material REF Price cat.

KOC® MU 3.0 15 Ti6Al4V 13-455830 L

KOC® MU 3.7 15 Ti6Al4V 13-455831 L

KOC® MU 4.1 12 Ti6Al4V 13-455832 L

KOC® MU 4.1 15 Ti6Al4V 13-455833 L

KOC® MU 5.0 10 Ti6Al4V 13-455834 L

KOC® MU 5.0 12 Ti6Al4V 13-455835 L

ACCESSORIES

Description Type Code REF Price cat.

Insertion tool IT MU 15 (for RAT 2) IT MU 15 13-418166 F

Adapter IT MU 15Adapter IT MU 15

13-418167 D

HandleFor adapters, can

be disassembled110 mm 13-311430 V

HandleFor adapters, Self-

locking110 mm 13-311431 V

Lab analogue for multiunit abutments IA K MU 13-418159 A

Screw for KOC® MU and BECES® MU SF K MU 13-418164 B

Long screw for TC MU

and TS MU (Tool: HT 1.25)Ti6Al4V SFL MU 13-418168 B

Castable abutment for multiunit

SF K MU has to be ordered separatelyPA MU 13-418119 B

Transfer coping (Provisorienbasis)

SF K MU has to be ordered separatelyTC MU 13-418161 D

Transfer, straight

SF K MU has to be ordered separatelyTS MU 13-418162 C

BECES® MU IMPLANTS

Description Material REF Price cat.

BECES® MU 3.6 14 Ti6Al4V 13-900330 N

BECES® MU 3.6 17 Ti6Al4V 13-900331 N

BECES®MU 3.6 20 Ti6Al4V 13-900332 N

BECES® MU 3.6 23 Ti6Al4V 13-900333 N

BECES® MU 5.5 10 Ti6Al4V 13-900334 N

BECES® MU 5.5 12 Ti6Al4V 13-900335 N

BECES® MU 5.5 14 Ti6Al4V 13-900336 N

BECES® MU 7.0 10 Ti6Al4V 13-900337 N

BECES® MU 7.0 12 Ti6Al4V 13-900338 N

KOC® MU and BECES® MU are available with a pre-angulation of 15 degrees. The implant-necks may be

bent max. 15 degrees. This will allow to create angulations between 0 and 30 degrees. Compared to the

implants systems solbd by N.B. the thread of the Multi-Unit-Heads provide a larger diameter, which helps

preventing fractures of the screw.

A difference to the displayed

No-Itis® implant-colour has

no impact on the quality.

7

a) Enossal length: 15 / 17 mm

b) Enossal Ø 3.2 / 3.7 / 4.1mm

c) Abutment length: 6.8 mm

d) Neck Ø 2.3 mm

e) Neck length 6 mm

KOC®TX IMPLANTS

Straight KOC® implants for crowns and bridges

Description Code KDS Enossal Ø Neck length REF Price cat.

KOC TX 3.2 15 E max 3.2 5.5 mm 13-455181 F

KOC TX 3.2 17 E max 3.2 5.5 mm 13-455182 F

KOC TX 3.7 15 G max 3.7 5.5 mm 13-455183 F

KOC TX 3.7 17 G max 3.7 5.5 mm 13-455184 F

KOC TX 4.1 15 L max 4.1 5.5 mm 13-455185 F

KOC® TX is a comperrsion-screw-implant with a long neck (6mm). KOC® TX is used in situation with thick mucosa and especially in the tuberosity. The

rough thread areas must be inserted fully into the bone. KOC® TX should be used without flap preparation. The nominal diameter is measured at the

broadest section of the compression thread.

b

a

de

c

IMPLANTS

TEMPBASE® TEMPORARY BASE

Description REF Price cat.

TPB K - temporary base, PEEK (for small head) 13-455261 C

TPB B - temporary base, PEEK (for large head) 13-462026 C

Temporary prosthesis base with internal and external grooves. Can be directly snapped on to the head of a KOC®

implant and if necessary secured with a little provisional cement. Is polymerized directly into the long term tem-

porary bridge. Intended service life 6 month.

KOC® MICRO IMPLANTS

Recommended

insertion depth

a) enossal length: 6 - 15 mm

b) max. enossal Ø small head: 3.3 mm

max. enossal Ø large head: 3.9 mm

c) neck Ø: 2.3 - 2.8 mm

Material: Ti6Al4V ELI

a

b

c

The head of the implant is prepared for the

connection with two stacked titan wires of

1.5 mm Ø each by intra-oral welding.

A difference to the displayed No-Itis®

implant-colour has no impact on the

quality.

Description enossal Ø Length Head Hals Ø Drill ** REF Price cat.

KOC Micro 3.0 10* 3.0 mm 10 mm small 2.3 mm DOS 1 or BCD 1 13-455900 F




KOC Micro 3.7 6 3.7 mm 6 mm large 2.5 mm DOS 2 or BCD 2 13-455910 F









KOC Micro 5 10 5 mm 10 mm large 2.8 mm DOS 5 13-455925 F

KOC Micro 5 12 5 mm 12 mm large 2.8 mm DOS 5 13-455926 F

KOC MicroD 3.7 6 3.7 mm 6 mm gross 2.0 mm DOS 2 or BCD 2 13-455950 G









KOC MicroD 5 10 5 mm 10 mm gross 2.0 mm DOS 5 13-455963 G

KOC MicroD 5 12 5 mm 12 mm gross 2.0 mm DOS 5 13-455964 G

Max. torque for insertion for KOC® Micro and KOC® MicroD implants is 100 Ncm.

* For these implants the max. torque for insertion is 80 Ncm.

** In very dense bone it may be necessary to enlargen the crestal part of the drill hole with a twistdrill

2 mmd or 2.5 mmd, up to a depth of 2.5 - 3mm.

KOC® MicroD implants

with large head are

delivered incl. lab-set

consisting of REF 462111,

REF 462030 and REF 462086.

a

b

c


b) max. enossal Ø large head: 3.9 mm

c) neck Ø: 2.0 mm

Material: Ti6Al4V ELI

KOC® MICRO D IMPLANTS

deliv

cons

8

ADAPTERS & ANALOGUES

CAUTERISABLE

These adapters are used by the dental technician for creating bridge framework wax-ups. Protruding head

material is removed by the dentist at the framework try-in.

ADAPTERS FOR CEMENTATION (TI6AL4V)

These adapters are placed on KOC® implants to compensate for diverging paths of insertion. Resin cements are preferred. The implant head should be

roughened first. Protruding parts of the head are subsequently removed. A direct impression is taken on the adapter.

Description Hight H REF Price cat.

AAL 15 KK Adapter, 5 pieces, reducible 7.5 13-462045 E


AAA Abutment analogue for angulation adapter 13-462049 B


ZAA15 KK Adapter, 15° 7.4 13-462047 E

ZAA25 KK Adapter, 25° 7.7 13-462048 E

LAB ANALOGUE FOR ANGULATION ADAPTER


PA AAA Castable abutment for AAA (5 pieces / pack) 13-462050 A

CASTABLE ABUTMENT AND IMPRESSION TRANSFER

ADAPTERS FOR CEMENTATION (ZIRCONIA)


AA15 KK Adapter, 15° 7.5 13-462036 C

AA25 KK Adapter, 25° 7.8 13-462046 C


AA5 15° Adapter short, for large head 13-462052 C

AA5 25° Adapter short, for large head 13-462053 C

AA15 KK

ZAA15 KK

AA5 15°

ZAA25 KK

AA5 25°AA5 15° AA5 25°

CEMENTABLE BALL FOR KOC AND KOC TX


Cementable ball ZKK3 13-462038 C

ZKK3 is cemented on KOC® implants (roughen head and abutment). The projecting part of the implant head

can be shortened afterwards if the vertical dimension requires this. The counterpart is made of soft relining

material, or the NC 3 nylon cap is used.


Nylon coping NC 3 NC 3 B

NC 3 is polymerized into the denture either directly or indirectly.

When using the indirect procedure, place ZKK3 on a lab analog (IA4) if required.

9

IMPLANTS

Straight , single-piece KOC® LOC Mini - implants for removable prosthetic

Description Enossal Ø Length Neck - Ø REF Price cat.

KOC LOC Mini 2.8 10 2.8 mm 10 mm 2.8 mm 13-455205 G




Compatibility: Localicer®. Insertion tool IT LOC K / REF 462333

Minimal differences to the displayed No-Itis® implant-colour has no influence on the quality of the surface.


b) enossal Ø: 3.0 / 3.7 mm

c) neck hight (bef. sandblasting): 3 mm

d) max Ø abutment: 3.8 mm

e) neck Ø: 2 / 2.8 mm

KOC®LOC - IMPLANTS

KOC®LOC MINI - IMPLANTS

KOC® LOC Implants are single-piece fixtures made of highly fracture-resistant Ti6Al4V ELI titanium alloy, doubly sandblasted, and then

osmoactive®-packaged.

a

b

c

d

e

Compatibility: Localicer®. Placement aid IT LOC K / REF 13-462333. We recommend to use minimally 6 implants per jaw

and to use a single denture as splinting.

INSERTION TOOL


IT LOC K insertion tool for KOC® LOC implants 13-462333 E

ACCESSORIES FOR LOCALICER®


b) enossal Ø: 2.8 mm

c) neck hight (bef. sandblasting): 3.5 mm

d) max Ø abutment: 3.8 mm

e) neck Ø: 2.3 mm

a

b

c

d

e

Pull-off force: *black 125 g, red 350 g, blue 500 g, pink 1000 g

*Black cap is for temporary solutions up to one month.

Description Code REF Price cat.

Instrument for mounting and de-mounting Localicer caps LOC Tool 13-462335 C

Analogue + impression cap set AA LOC 13-462337 C

Set with 4 nylon caps + 1 housing NCS 13-462338 C

Set of 2, yellow. With increased friction strength R-Cap 13-462336 B

SOON - with new No-Itis® surface!

Straight , single-piece KOC® LOC - implants for removable prosthetic

Description Code KDS Enossal Ø Length Neck - Ø REF Price cat.

KOC LOC 3.0 12 B 3.0 mm 12 mm 2 mm 13-455200 G

KOC LOC 3.0 15 C 3.0 mm 15 mm 2 mm 13-455201 G

KOC LOC 3.2 12 D 3.2 mm 12 mm 2 mm 13-455209 G

KOC LOC 3.2 15 E 3.2 mm 15 mm 2 mm 13-455210 G

KOC LOC 3.7 12 F 3.7 mm 12 mm 2.8 mm 13-455202 G

KOC LOC 3.7 15 G 3.7 mm 15 mm 2.8 mm 13-455203 G

10

IMPLANTS

Description Compression thread Enossal length Neck length REF Price cat.

KOC 3.7 9+3 9 mm 12 mm 3 mm 13-455800 G

KOC 3.7 11+3 11 mm 14 mm 3 mm 13-455801 G

KOC 3.7 13+3 13 mm 16 mm 3 mm 13-455802 G

KOC 3.7 16+3 16 mm 19 mm 3 mm 13-455803 G

KOC 3.7 20+3 20 mm 23 mm 3 mm 13-455804 G

KOC 3.7 23+3 23 mm 26 mm 3 mm 13-455805 G

KOC 4.1 6+3 6 mm 9 mm 3 mm 13-455810 G

KOC 4.1 9+3 9 mm 12 mm 3 mm 13-455811 G

KOC 4.1 11+3 11 mm 14 mm 3 mm 13-455812 G

KOC 4.1 13+3 13 mm 16 mm 3 mm 13-455813 G

KOC 4.1 20+3 20 mm 23 mm 3 mm 13-455814 G

KOC 5.0 6+3 6 mm 9 mm 3 mm 13-455820 G

KOC 5.0 9+3 8 mm 12 mm 3 mm 13-455821 G

KOC 5.0 11+3 11 mm 14 mm 3 mm 13-455822 G

KOC 5.0 13+3 13 mm 16 mm 3 mm 13-455823 G

KOC® Plus implants are delivered incl. lab-set consisting of REF13-462111, 462030 and 13-462086.

a) enossal length 9, 12, 14, 16, 19 mm

b) enossal Ø 3.7 / 4.1 / 5.0mm

c.) height of cutting thread 3.0 mm

d) height of compression thread 6, 9, 11, 13 mm

e) neck length (for mucosa) 3 mm

f ) head height 7.2 mm

g) max. diameter of the head 3.9 mm

KOC® PLUS are single piece implants with polished sharp apical threads and compression threads for placement in the spongious bone. KOC Plus

combines the advantages of a compression screw implant with the unexpected stability of anchorage in the 2nd

cortical. For use in the upper and the lower jaw. Made from highly compatible and proven titanium alloy (Ti6Al4V ELI), double sand-blasted and packed

osmoavtive. Screw in with IT2 BCS.

Example for use: Bi-cortical

anchorage of a KOC Plus implant

in the atrophied distal mandible

Example for use: Bi-cortical

anchorage of a KOC Plus implant in the area

of the floor of the nose

Example for use: Bi-cortical anchorage of a

KOC Plus implant in the area of the distal ma-

xilla (diameter 3.7 and 4.1)

a

b

e

g

f

c

d

Note: These indications are for experiences surgeons only. CT planning is recommended. Only polished parts of the cutting apical

threads should penetrate into the 2nd cortical max. 1.5 mm. In given indications (min 3 stable implants) the treatment should be

carried out in immediate loading protocols.

KOC® PLUS - IMPLANTS

INSERTION TOOLS


IT2 BECES For BECES implants with > Ø 5.5 mm / KOC X, KOC XB, KOC Plus 13-900030 E

IT2 S BECES For BECES implants with > Ø 5.5 mm / KOC X, KOC XB, KOC Plus 13-900038 E

IT2W Length 23 mm, for KOC and BECES implants 13-900039 C

AHB Adapter for implants > Ø 5.5 mm, fits the handgrip,

REF 311430 / 311431 / KOC X, KOC XB13-900037 F

Available with micro thread SOON!

11

DRILL SEQUENCES - OVERVIEW

DRILL SEQUENCES

Pilot drill Form drill Implant

DOS 1

---------------- KOC 3.0

DOS 2 KOC 3.2

DOS 3 (4)KOC 3.7

KOC 4.1

DOS 5 KOC 5.0

In very hard bone the implants should be inserted shlighty deeper and then turned back 1/2 round.

Normal / hard bone

Soft bone

Pilot drill Form drill Implant

DOS 1

---------------- KOC 3.0

---------------- KOC 3.2

DOS 2KOC 3.7

KOC 4.1

DOS 3 (4) KOC 5.0

DRILL SEQUENCES KOC PLUS IMPLANTS

Pilot drill: also for penetration of the 2nd corticals

The 2nd cortical should be

penetrated in regular bone

densitiy with the 2.0 mm drill only

Implant

BCD1

or

BCDXI

Twist Drill 2.0

(Length 21, 30 or 40)

DOS 2 KOC PLUS 3.7

DOS 3 KOC PLUS 4.1

DOS 3 - ( DOS 5 ) KOC PLUS 5.0

HEATLESS®-DRILL «DOS» FOR IMPLANTS WITH CONICAL CORE

Surgical steel, color coded, depth coded and autoclavable. The drill is marked with laser depth markings.

Description Color max. working length REF Price cat.

DOS 1 yellow 17 mm 13-455311 D

DOS 2 black 17 mm 13-455312 D

DOS 3 red 17 mm 13-455313 D

DOS 4 blue 21 mm 13-455314 D

DOS 5 green 17 mm 13-455315 D


DOS 6 transparent 15 mm 13-455316 D

DOS 6: The tip of this drill is 2 mm shorter, allowing 2 mm deeper drilling than nominally indicated on

the drill. This allows the conical bone cavity to be circularly expanded in the crestal region only without

increasing the drilling depth. DOS 6 is intended for use with KOC 5.0 12, KOC 5.0 10 and KOC 4.1 8 im-

plants.

12

SURGICAL INSTRUMENTS AND TOOLS

Description Type Angulation Length for implant REF Price cat.

IT K long –––––– 20 mm KOC, KOC B, KDS 13-462320 C

ITX K extralong –––––– 45 mm KOC, KOC B, KDS 13-462321 C

ITS K short –––––– 7 mm KOC, KOC B, KDS 13-462322 C

ITWH K *contra-angle/

hex–––––– 23 mm KOC, KOC B, KDS 13-462323 C

ITW K contra-angle –––––– 23 mm KOC, KOC B, KDS 13-462331 C

IT 15 K long 15° 20 mm KOC A 13-462325 G

ITS 15 K short 15° 7 mm KOC A 13-462328 H

IT TB K long –––––– 20 mm KOC K 13-462327 D

Tool E ** long –––––– 20 mm KOC A, B 13-462377 D

IT TCA long –––––– 20 mm KOC E 13-425065 D

* for W&H contra-angles with new connection to the contra-angle only.

** Emergency tool for KOC and BECES

Description Type Length REF Price cat.

DX 2 Drill extender, extends by 19 mm 13-500704 D

Standardized probe PDG1-mm scale

for radiological measurements22 mm 13-425400 A

Radiol. measure pin CDG fits to DOS 1 13-420329 A

Ratchet RAT2for all Hex-instruments

and insertion tools13-425051 K

Ratchet RAT3angled, for all Hex-

instruments and insertion tools13-425052 S

Torque wrench TW2 10 - 70 Ncm 13-425402 S

UAW *

Universal ratchet adapter for all angled

handpiece tools, use with RAT2 rat-

chet. Max. 30 Ncm

13-425107 E

It is recommended to have the torque ratchets recalibrated by us once a year.

* Do not use UAW in combination with RAT2 with Heatless® bone drills. The maximum insertion

torque for UAW and Heatless® bone drills is 35 Ncm. UAW may therefore be used only with TW2.

INSTRUMENTS AND TOOLS

INSERTION TOOLS

*

Sechskant

TITANIUM CROWN BASE AND BAR-PROFILES

Multi-purpose titanium caps for: - creating immediately lasered bridge-frames, together with bar profiles (without female profiles)

- x-ray controll, controll of the modellation

- direct polymerisation into bridges

- direct veneering with Titanium-ceramics

MA4 for: KOC, KOC B, KOC A, BECES 3.5, BECES 4.5 / MA5 for: KOC X, KOC Plus, BECES 3.6, BECES 4.6 - BECES 12 Material: TiAl4V


MA4 Titanium-cap, radio-opaque 13-462090 B



Bar sleeve, titanium, large; 3.0 mm high, 2.2 mm wide, 55 mm long SP1 B

Bar sleeve, titanium, small; 2.3 mm high, 1.6 mm wide, 55 mm long SP2 B

Titanium bar matrix for SP 1, 55 mm long SP6 G


13


HANDGRIP - TRAY

Description Length REF Price €

BCD 1 Adapter 100 mm 13-310511

Twist Drill 2.0 100 mm 13-310512

Twist Drill 2.5 100 mm 13-310513

Adapter RA 60 mm 13-310530

Adapter AHK 70 mm 13-462319

Adapter AHB 70 mm 13-900037

Adapter IT MU 15 60 mm 13-418167

Handgrip 110 mm 13-311430

Handgrip-Tray (empty) 13-60043 69,90

Handgrip-Tray (with content) 13-S60043 639,00

HANDGRIPS AND ADAPTERS FOR KOC® AND BECES®

HANDGRIP

Length 110 mm

REF 13-311430

Price cat. V

Dismountable, can be

cleaned manually.

HANDGRIP

Length 110 mm

REF 13-311431

Price cat. V

Not dismountable. Cleaning in

ultrasonic bath at 45° C, with alkaline clean-

sing medium.

ADAPTER AHK

Length 70 mm

REF 13-462319

Price cat. B

ADAPTER AHB

Length 70 mm

REF 13-900037

Price cat. F

TWIST DRILL 2.5

Length 100 mm

REF 13-310513

Price cat. F

TWIST DRILL 2.0

Length 100 mm

REF 13-310512

Price cat. F

BCD 1 ADAPTER

Length 100 mm

REF 13-310511

Price cat. F

ADAPTER RA

Length 60 mm

REF 13-310530

Price cat. C

ADAPTER IT MU 15

Length 60 mm

REF 13-418167

Price cat. D

KOC®

KOC® B

KOC® T

V KDS

BECES 3.5

BECES 4.5

KOC® X

KOC® XB

KOC® PLUS

BECES 3.6

BECES 4.6

from > 5.5

Adapter for all

contra-angle-

instruments,

fits handgrip

KOC® MU

BECES® MU

Insertion toolsDrill

Size of closed tray

B = 90 mm / L = 195 mm / H = 45 mm

T

A

A

A

A

H

H

H

14

INSTRUMENT - TRAY AND INFORMATIONS

• Anchorage for crowns, bridges and bars, given a bone supply adequate with regard to bone quality, bone width and bone height.

• Nothing has been reported concurrently on the use of KOC® in combination with bone augmentation.

• Anchorage of prostheses using bars and ball retainer systems.

• Single tooth treatment (only KOC® - Implants !).

APPLICATION AREAS (INDICATIONS) KOC®

NOTES ON THE CARE OF SURGICAL STEEL INSTRUMENTS

Surgical steel instruments can quickly become damaged if inadequately or improperly cared for. Only the special solvents for cleaning surgical steel from blood and

debris should be used. (i.e. Dentatrend disinfection products) In case of doubt, consult Dr. Ihde Dental AG, Switzerland: [email protected].

Not recommended are:

• disinfectants / cleaners with a high chlorine content.

• disinfectants / cleaners with a high oxalic acid content.

Not recommended for instruments with colour coding are:

• Excessively high solvent concentrations, disinfectants / cleaners with the components mentioned above.

• Excessive temperatures in machine cleaning and sterilisation.

• Never exceed 134° C!

STARTER - TRAY

Description REF Price €

IT K 13-462320

IT S K 13-462322

ITW K 13-462331

IT LOC K 13-462333

KDS 3.2 12 13-455223

KDS 3.2 15 13-455224

KDS 3.7 15 13-455234

IT MU 15 13-418166

DOS 1 13-455311

DOS 2 13-455312

DOS 3 13-455313

Torque wrench TW2 13-425402

Starter-Tray (with content)* S13-60041-K 828,60

* Empty tray upon request

Description

IT K

IT S K

ITW K

IT LOC K

KDS 3.2 12

KDS 3.2 15

DS 3.7 15

MU 15

OS 1

S 2

3

ue wren

er-Tray

y tray

I

K

KD

KD

IT M

DO

DOS

DOS

Torqu

Starte

* Empty

Autoclavable up to 134 °C, do not use in dry heat sterilisation.

This surgical tray contains all drills and tools for first steps with the system KOC®. Material: autoclavable plastic

15

BECES®

BECES® is the ideal implant for immediately loaded, cortically anchored restorations.

BECES® N implants seal and compress the 1st cortical, thereby dividing the long axis of

the implant favourably in two sections.

BECES® EX implants may be immediately placed in extraction sockets if the basal support

is sufficient. The anti-rotation protection provides more stability, preventing also rotations

caused during prosthetic manupulations.

BECES® implants are made out of high-strength, biocompatible (Ti6Al4V) titanium alloy.

BE

CE

S® N

BE

CE

S® E

X

BE

CE

S®

IMPLANTS FOR

MAXIMUM SUCCESSS

16

Description a b REF Price cat.

BECES 3.5 10 3.5 10 13-900208 G

BECES 3.5 14 3.5 14 13-900210 G

BECES 3.5 17 3.5 17 13-900211 G

BECES 3.5 20 3.5 20 13-900212 G

BECES 3.5 23 3.5 23 13-900213 G

BECES 3.5 26 3.5 26 13-900214 G

BECES 3.5 29 3.5 29 13-900215 G

BECES 3.5 32 3.5 32 13-900216 G

BECES 3.5 35 3.5 35 13-900217 G

BECES 3.5 38 3.5 38 13-900218 G

BECES 4.5 14 4.5 14 13-900220 G

BECES 4.5 17 4.5 17 13-900221 G

BECES 4.5 20 4.5 20 13-900222 G

BECES 4.5 23 4.5 23 13-900223 G

BECES 4.5 26 4.5 26 13-900224 G

BECES 4.5 29 4.5 29 13-900225 G

Insertion tools: IT KOC, ITX KOC, ITS KOC, Adapter AHK.

BECES® implants are delivered incl. lab-set

consisting of REF 462111, 462029 and 462088.

Screw implant for bi- or multicortical placement for usage in bridge contructions. The implant may be

placed into fresh extraction sockets and must splinted immediately. Completely machined/polished surface.

The abutment head is identical with KOC®. Self cutting thread with anti rotation feature.

a) diameter of thread: 3.5 - 4.5 mm

b) endosseous length: 10 - 38 mm

c) abutment height: 6.8 mm

d) max. abutment diameter: 3.35 mm

f) max. crestal diameter of shaft: 2 mm

g) length of thread: 5.5 mm

h) Type N collar: 2.8 mm

Type EX collar: 3.5 mm

Tool: for small head BECES

BECES® IMPLANTS

Description a b g REF Price cat.

BECES 2.7 10 13-900200

BECES 2.7 12 13-900201

BECES 2.7 14 13-900202

BECES 2.7 17 13-900203

BECES 2.7 20 13-900204

BECES 2.7 23 13-900205

BECES 2.7 may not be used as single tooth implant. If in very thin ridges only BECES 2.7 should be used, it is

recommended to place at least 12 implants per jaw in cortical engagement.

Recommended drills: DOS1 and/or DOS2.

a) diameter of thread: max. 2.7 mm




e) length of bending zone: 2.55 mm

f) max. crestal diameter of shaft: 1.9 mm

g) length of thread: 4.5 - 5.5 mm

Tool: for small head BECES

BECES® IMPLANTS

IMPLANTS

BECES 2.7 implants are used for the following indications:

• supporting (adjunct) implants for the cortical fixation of bridges

• creating tripod-support in specific intra-oral areas, for the cortical fixation of bridges

• creating anchorage in the 1st, 2nd, 3rd cortical

• temporary implant placement in cases when final implantation is not yet possible or not advisable

f

f

a

d

g

e

c

b

BE

CE

S® 2

.7 1

7B

EC

ES

® 4

.5 1

7

BCS 2.7 implants are sold with 10 pieces / pack only.

17

IMPLANTS

Description a b e f i REF BECES® / BECES® N REF BECES® EX Price cat.

BECES 3.6 10 3.6 10 4 2.0 13-900285 H

BECES 3.6 12 3.6 12 6 2.0 13-900284 H

BECES 3.6 14 3.6 14 5 2.0 N 13-900286 H

BECES 3.6 17 3.6 17 8 2.0 N 13-900287 H

BECES 3.6 20 3.6 20 11 2.0 N 13-900288 H

BECES 3.6 23 3.6 23 14 2.0 N 13-900289 H

BECES 3.6 26 3.6 26 17 2.0 N 13-900290 H

BECES 3.6 29 3.6 29 20 2.0 N 13-900291 H

BECES 3.6 14 EX 3.6 14 5 2.0 EX 13-900080 H

BECES 3.6 17 EX 3.6 17 8 2.0 EX 13-900081 H

BECES 3.6 20 EX 3.6 20 11 2.0 EX 13-900082 H

BECES 3.6 23 EX 3.6 23 14 2.0 EX 13-900083 H

BECES 3.6 26 EX 3.6 26 17 2.0 EX 13-900084 H

BECES 3.6 29 EX 3.6 29 20 2.0 EX 13-900085 H

BECES 3.6 32 EX 3.6 32 25 2.0 EX 13-900086 H

BECES 3.6 35 EX 3.6 35 28 2.0 EX 13-900087 H

BECES 4.6 8 4.6 8 3 2.2 13-900299 H

BECES 4.6 10 4.6 10 4 2.2 13-900292 H

BECES 4.6 12 4.6 12 6 2.2 13-900300 H

BECES 4.6 14 4.6 14 5 2.2 N 13-900293 H

BECES 4.6 17 4.6 17 8 2.2 N 13-900294 H

BECES 4.6 20 4.6 20 11 2.2 N 13-900295 H

BECES 4.6 23 4.6 23 14 2.2 N 13-900296 H

BECES 4.6 26 4.6 26 17 2.2 N 13-900297 H

BECES 4.6 29 4.6 29 20 2.2 N 13-900298 H

BECES 4.6 14 EX 4.6 14 5 2.0 EX 13-900090 H

BECES 4.6 17 EX 4.6 17 8 2.0 EX 13-900091 H

BECES 4.6 20 EX 4.6 20 11 2.0 EX 13-900092 H

BECES 4.6 23 EX 4.6 23 14 2.0 EX 13-900093 H

BECES 4.6 26 EX 4.6 26 17 2.0 EX 13-900094 H

BECES 4.6 29 EX 4.6 29 20 2.0 EX 13-900095 H

BECES 4.6 32 EX 4.6 32 25 2.0 EX 13-900096 H

BECES 4.6 35 EX 4.6 35 28 2.0 EX 13-900097 H

Insertion tools: IT2 BECES, IT2 S BECES, Adapter AHB

a) max. apical thread Ø: 3.6 - 4.6 mm



d) max. abutment Ø: 3.9 mm

e) length of polished shaft: 3 - 20 mm

f) crestal Ø of shaft: 2.0 mm

g) length of apical thread: 5.5 mm

h) height of crestal micro-thread/prop: 2.5 mm

i) BECES® no collar

BECES® N prop 2.5 mmd

BECES® EX prop/microthread 3.5 mmd

BECES® IMPLANTS WITH LARGE HEAD

BE

CE

S® N

BE

CE

S®

BE

CE

S® E

X

Application

BECES N are for healed bone areals with density D2 - D6

BECES EX for extraction sockets and healed bone areals with density D4 - D6

The prop must be submerged 0.5 - 1 mm under the crestal bone level.

BECES® implants with large head

are delivered incl. lab-set consisting

of REF 462111, 462036 and 462086.

a

b

c

d

e

g

i

h

Recommended

insertion depth

18

Description a b e f REF Price cat.

BECES 5.5 8 5.5 8 3 2.3 13-900255 K

BECES 5.5 10 5.5 10 4.5 2.3 13-900281 K

BECES 5.5 12 5.5 12 4.5 2.3 13-900250 K

BECES 5.5 14 5.5 14 6.5 2.3 13-900251 K

BECES 5.5 17 5.5 17 9.5 2.3 13-900252 K

BECES 5.5 20 5.5 20 12.5 2.3 13-900253 K

BECES 7 8 7 8 3 2.3 13-900258 K

BECES 7 10 7 10 4.5 2.3 13-900282 K

BECES 7 12 7 12 5 2.3 13-900260 K

BECES 7 14 7 14 7 2.3 13-900261 K

BECES 7 17 7 17 10 2.3 13-900262 K

BECES 7 20 7 20 13 2.3 13-900263 K

BECES 9 8 9 8 2.4 2.3 13-900269 M

BECES 9 10 9 10 2.8 2.3 13-900270 M

BECES 9 12 9 12 4.8 2.3 13-900274 M

BECES 9 14 9 14 6.8 2.3 13-900271 M

BECES 10.5 10 10.5 10 2.8 2.4 13-900276 M

BECES 10.5 12 10.5 12 4 2.4 13-900277 M

BECES 10.5 14 10.5 14 6 2.4 13-900278 M

BECES 10.5 17 10.5 17 9 2.4 13-900280 M

BECES 12 8 12 8 2.5 2.3 13-900279 O

BECES 12 10 12 10 2.7 2.3 13-900272 O

BECES 12 12 12 12 4 2.3 13-900275 O

BECES 12 14 12 14 6 2.3 13-900273 O

Insertion tools: IT2 BECES, IT2 S BECES, Adapter AHB

Minimal differences to the displayed No-Itis® implant-colour has no influence on the quality of the

surface.

BECES® implants with large head are

delivered incl. lab-set consisting of

REF 462111, 462036 and 462086.

a

g

c

d

f

b

a) thread Ø: 5.5 - 12 mm

b) enossal length: 10 - 20 mm

c) Abutment height: 7.2 mm

d) Abutment Ø: 3.9 mm

e) length of polished shaft: 3 - 13 mm

f) crestale diameter of shaft: 2.3 - 2.4 mm

g) length of thread: 5.5 - 6.5 mm

BECES® IMPLANTS WITH LARGE HEAD

IMPLANTS

19

ACCESSORIES

APPLICATION

BECES® sizes 3.5/4.5 (small head) are compatibel with the following analogues & impression posts of the KOC®-systems:

ACCESSORIES FOR BECES® 3.5 AND BECES 4.5

Beces 3.5 4.5

Beces

3.6 4.6 5.5 7 9 10.5 123.6 4.6

Code

REF

TSPA 5* (Plastic)

13-462030

IA4/IAU (Metal)

13-462112

IA4/IAU (Plastic)

13-462111

POB

13-462086

TPB B

13-462026

PA X

13-462136

Impression post

internally round

Pack of 5

Double

analogue

Double

analogue

Pack of 5

Castable

abutment

Pack of 5

Tempbase for

KOC X / KOC XB

PEEK

Impression-

and castable

abutment

Pack of 5

Price cat. B A B B C B

Parts for Beces 3.6, 4.6, 5.5, 7, 9, 10.5, 12 and KOC X, KOC XB, as well as COI.

or or

5.5 7 9 10.5 12

Impression and laboratory accessories

Code REF

TSPA 4

13-462029

IA4/IAU

13-462112

IA4/IAU

13-462111

PO4

13-462088

TPB K

13-455261

Impression post

castable

internally round

Pack of 5

Double analogue

(Metal)

Double analogue

(Plastic)

Pack of 5

Castable abutment

7 mm high, white

internally round

Pack of 5

Tempbase

for KOC, Beces 3.5,

Beces 4.5

PEEK

Price cat. B A B B C

or

in the lower jaw in the upper jaw in the upper jaw

BECES® 3.5 / 4.5 / 5.5

Inserted into local bone, cortical

(basal/lateral) support

BECES® 3.5 / 4.5 / 5.5

inserted into the lateral maxilla

BECES® 12

Basal/sinusal and lateral support

20

DRILLS


BCD 1 yellow 15 mm 13-900240 C

BCD 2 black 15 mm 13-900241 C

BCD 3 red 15 mm 13-900242 C

BCDX 1 yellow 15 mm 13-900243 C

BCDX 2 black 15 mm 13-900244 C

BCDX 3 red 15 mm 13-900245 C

Description Ø max. working length REF Price cat.

Twist Drill 2.0 / 21 2.0 mm 21 mm 13-90022 D




Conical drill with 3 cutting edges. For use as first drill for all crestal dental implant systems. May be used in the handgrip or at slow speed with very little

pressure. The drill finds its way between corticals.

TWIST DRILL

PATHFINDER-DRILL

INSERTION TOOLS AND ADAPTERS

Description REF Price cat..

IT K, for BECES implants with Ø 3.5 mm + 4.5 mm 13-462320 C


IT2 BECES, for BECES implants with Ø 3.6, 4.6, 5.5, 7, 9, 10.5, 12 mm 13-900030 E

IT2 S BECES, for BECES implants with Ø 3.6, 4.6, 5.5, 7, 9, 10.5, 12 mm 13-900038 E


AHB, for BECES implants with Ø 3.6, 4.6, 5.5, 7, 9, 10.5, 12 mm.

For handgrips REF 311430 & 31143113-900037 F


Adapter, for contra-angle instruments.

For handgrips 13-311430 & 13-31143113-310530 C


AHK, Adapter for BECES 3.5/4.5 & KOC®.

For handgrips 13-311430 & 13-31143113-462319 B


BCD 1 Adapter Pathfinder for handgrip; length 100 mm 13-310511 F


Twist Drill 2.0, cylindrical drill 2.0 mm for handgrip; length 100 mm 13-310512 F

Twist Drill 2.5, cylindrical drill 2.5 mm for handgrip; length 100 mm 13-310513 F

I 47 mm II 47 mm I

I 15 mm I

I 39 mm I

21

ANGULATION-ADAPTER FOR KOC®, BECES® AND DISKOS®

FOR CEMENTATION

These adapters are used to change the direction of the abutment head in BECES 3.5 and 4.5 mm implants. Strong permanent cements (Fuji Plus or si-

milar) must be used. Both the implant head and the inside of the adapter must be roughened. Over-projecting parts of the implants head are trimmed

after the cement has set. The impression is taken directly on the adapter or with the transfer PA AAA.

CASTABLE ANGULATION ADAPTER


AAL 15 KK Adapter, 15°, reducible (Pack of 5) 7.5 13-462045 E


AAA Abutment analogue for angulation adapter 15° and 25° 13-462049 B

LAB ANALOGUE FOR ANGULATION ADAPTER (15°AND 25°)


PA AAA Castable abutment and transfer for AAA (Pack of 5) 13-462050 B

CASTABLE ABUTMENT AND IMPRESSION TRANSFER

This castable is used for direct modellation. During the metal try in, over-projecting parts of the implant`s head are trimmed away.

CEMENTING - ADAPTER


B21 Replacement abutment for Beces, internal diameter 2.15 mm 13-900316 A

B21 ANAAnatomic replacement abutment for Beces, height above

mucosa 7.5mm, trangingival height 1.5 mm, fully grindable 13-462021 C

Replacement head for cementations. For Beces imlpants with shaft-diameter of up to 2.1mm. Larger shafts must be trimmed. Adjusts the vertical posi-

tion of the abutment. Use Fuji Plus for cementing. Machined surface, with drain for cement. Material: Ti6Al4V ELI

TITANIUM CROWN BASE AND BAR-PROFILES

Multi-purpose titanium caps for: - creating immediately lasered bridge-frames, together with bar profiles (without female profiles)

- x-ray controll, controll of the modellation

- direct polymerisation into bridges

- direct veneering with Titanium-ceramics

MA4 for: KOC, KOC B, KOC A, Beces 3.5, Beces 4.5 / MA5 for: KOC x, KOC Plus, Beces 3.6, Beces 4.6 - Beces 12 Material: TiAl4V





Bar sleeve, titanium, large; 3.0 mm high, 2.2 mm wide, 55 mm long SP1 B

Bar sleeve, titanium, small; 2.3 mm high, 1.6 mm wide, 55 mm long SP2 B



NEW

ALSO FOR

WELDING

Description Hight Material REF Price cat.

AA15 KK Adapter, 15° 7.5 Ti6Al4V 13-462036 C

AA25 KK Adapter, 25° 7.8 Ti6Al4V 13-462046 C

AA5 15° Adapter short for large head Ti6Al4V 13-462052 C

AA5 25° Adapter short for large head Ti6Al4V 13-462053 C

ZAA15 KK Adapter, 15° 7.4 Zirconia 13-462047 E

ZAA25 KK Adapter, 25° 7.7 Zirconia 13-462048 E

AA15 KK AA25 KK

ZAA15 KK

B21

ZAA25 KK

B21 ANAB21 ANAB21

AA5 15° AA5 25°

AA15 KK

AA5 15°AA5 15

AA25 KK

AA5 25°AA5 25

22

INSTRUMENT TRAY, SURGICAL INSTRUMENTS AND ACCESSORIES

STARTER - TRAY

Autoclavable up to 134 °C, do not use in dry heat sterilisation. This surgical tray contains

all drills and tools for first steps with the system BECES®. Material: autoclavable plastic


IT K 13-462320

ITS K 13-462322

IT2 BECES 13-900030

IT2 S BECES 13-900038

BCD 1 13-900240

Twist Drill 2.0 / 21 13-90022

Twist Drill 2.0 / 30 13-90020

Twist Drill 2.5 / 21 13-90026

IT MU 15 13-418166

Torque wrench TW2 13-425402

Starter-Tray with content (empty Tray upon request) S13-60040-K 728,80

Description Type Length REF Price cat.

DX 2 Drill extender, extends by 19 mm 13-500704 D

Standardized probe PDG 1-mm scale for radiological measurements 22 mm 13-425400 A

Radiol. measure pin CDG fits to DOS 1, locked usage only 13-420329 A

Ratchet wrench RAT 2 For insertion aids 13-425051 K

Ratchet wrench RAT 3 angled, for insertion aids 13-425052 S

Torque wrench* TW2 10 - 70 Ncm 13-425402 S

UAW ***Universal ratchet adapter for all angled

handpiece tools, use with RAT2 ratchet.

Max. 30 Ncm

13-425107 E

Handle For adapters, can be disassembled 110 mm 13-311430 V

Handle ** For adapters, Self-locking 13-311431 V

* It is recommended to have the torque ratchets recalibrated by us once a year.

** for cleanig this instrument an ultrasonic cleaning device and a thermo-desinfector (i.e. Miele TD-series) are required. If these devices are not available in the dental office the handle with

REF 13-311430 should be purchased instead.

*** Do not use UAW in combination with RAT2 with Heatless® bone drills. The maximum insertion torque for UAW and Heatless® bone drills is 35 Ncm. UAW may therefore be used only with TW2.

INSTRUMENTS AND TOOLS

It is recommended to have the torque rat hchets recali

Description Type Angulation Length for Implant REF Price cat.

IT K long –––––– 20 mm Beces, KOC, KOC B, KDS 13-462320 C

ITX K extralong –––––– 45 mm Beces, KOC, KOC B, KDS 13-462321 C

ITS K short –––––– 7 mm Beces, KOC, KOC B, KDS 13-462322 C

IT 15 K long 15° 20 mm Beces, KOC A 13-462325 E

ITS 15 K short 15° 7 mm Beces, KOC A 13-462328 E

IT TB K long –––––– 20 mm Beces, KOC K 13-462327 G

IT2 BECES long –––––– 20 mm Beces, KOC, KOC B, KDS 13-900030 H

IT2 S BECES short –––––– 7 mm Beces, KOC X, KOC Plus 13-900038 D

IT2W –––––– 23 mm KOC, Beces 13-900039 C

Tool E * long –––––– 20 mm Beces, KOC B 13-462377 D

IT TCA long –––––– 20 mm Beces, KOC E 13-425065 D

* Emergency tool for KOC and BECES

INSERTION TOOLS

*

23

ZDI IMPLANTS

a) max. diameter of thread: 4.6 mm

b) Endosseoous length: 35 - 55 mm

c) Abutment height: 7 mm


f ) Diameter of shaft: 2.0 mm

g) upper diameter of shaft: 2.2 mm

h) length of thread: 10 mm

ZDI: ZYGOMA - SCREW - IMPLANTS

ZDI-Implants are placed trans-sinualy or below/inside the crista zygomatico-alveolaris, and in the alveolar crest of the maxilla. For cortical anchorage in

the zygomatic bone. Depending on the anatomic situation the smooth parts of the implants are positioned below the Schneiderian mebrane or below

the oral muscosa.

These implants are to be used only by trained surgeons. ZDI-Implants provide a bending area below the cementing abutment. Therfore they can be aligned

with other abutments in the center of the crest after the implant has been placed. An additional vertical osteotomy may be necessary (see the drawing)

. This implant can be used in combination with tubero-pterygoid screw implants (BECES). The treatment protocol requires immediate splinting. Material:

Ti6AI4V ELI.

Description Thread Ø Length w/o head REF Price cat.

ZDI 4.6 35 4.6 35 13-900100 F

ZDI 4.6 37.5 4.6 37.5 13-900101 F

ZDI 4.6 40 4.6 40 13-900102 F

ZDI 4.6 42.5 4.6 42.5 13-900103 F

ZDI 4.6 45 4.6 45 13-900104 F

ZDI 4.6 47.5 4.6 47.5 13-900105 F

ZDI 4.6 50 4.6 50 13-900106 F

ZDI 4.6 52.5 4.6 52.5 13-900107 F

ZDI 4.6 55 4.6 55 13-900108 F


Twist Drill 2.2 / 50 For Zygoma implants, SS 13-90021 D

Twist Drill 2.2 / 55 For Zygoma implants, SS 13-90023 D

Twist Drill 2.2 For handgrip to Zygoma implants, L = 100 mm 13-310514 F

TWIST DRILL

c

b

a

d

f

g

h

ACCESSORIES FOR ZDI

ZDI-Implants may be used in a trans-sinusal or sub-mucosal manner. The abutment head is aligned with the

tooth arch through bending.

Zygomatic bone Zygomatic bone

Maxillary sinus

Zygomatic bone

Maxillary sinusMaxillary sinus

Code

REF

TSPA 5 (plastic)

13-462030

Impression post

internally round

Pack of 5

IA4/IAU (metal)

13-462112

Double analogue

IA4/IAU (plastic)

13-462111

Double analogue

Pack of 5

POB

13-462086

Castable abutment

Pack of 5

Price cat. B A B B

24

Autoclavable up to 134 °C, do not use in dry heat sterilisation. This surgical tray contains all drills and tools for first steps with the system BECES®.

Material: autoclavable plastic

INSTRUMENT TRAYS

STRATEGIC IMPLANT® - TRAY

STRATEGIC IMPLANT® - TRAY

Autoclavable up to 134 °C, do not use in dry heat sterilisation.

This surgical tray contains all drills and tools for first steps with

the system BECES®.

Material: autoclavable plastic


Starter-Tray empty 13-60012 399,90

Description REF

ITS K 13-462322

DOS 1 13-455311

Twist Drill 2.0 / 21 13-90022

Twist Drill 2.0 / 30 13-90020

Twist Drill 2.0 / 40 13-90019

Twist Drill 2.2 / 50 13-90021

Twist Drill 2.2 / 55 13-90023

Twist Drill 2.5 / 21 13-90026

IT K 13-462320


BCDX 1 13-900243

IT2 BECES 13-900030

IT2 S BECES 13-900038

KC 7-4W 13-462221-4W

KCD 7-4W 13-462237-4W

LC 9-6W 13-462261-6W

Ratchet RAT2 13-425051

Starter-Tray with content 13-60049 859,90

25

UTILIZING THE PATIENT’S OWN BONE SUBSTANCE Avoid augmentation procedures to create endosseous anchorage. Avoid additional surgical risks

and save time and money

IMMEDIATE LOADING Avoid intermediate prosthodontic steps. No reentry/implant exposure surgery. This is what patients want.

VERY LITTLE EXTERNAL MATERIAL Trans-osseous implants displace up to 60% less bone substance. Bone integrity and perfusion are barely impaired.

IMMEDIATE IMPLANT PLACEMENT AFTER EXTENSIVE TOOTH EXTRACTIONS Possible even in cases with periodontal involvement

(cleaning, perio treatment and implant placement in a single step). Cost and time savings – excellent price-performance ratio for all patients.

FAVOURABLE DISTRIBUTION OF BIOMECHANICAL LOADS Loads are distributed only to the cortical regions, which are more resistant to resorption

and stronger and regenerate more quickly. Immediate loading possible thanks to bicortical support and immediate prosthodontic splinting. High

resistance to bacterial infection, since the site of the force-transmitting endosseous aspects of the implant is far away from the site of bacterial invasion.

FEW COMPLICATIONS DURING THE SURGICAL PHASE Transosseous implants are very resistant to preoperative or intraoperative infection. Patients

are not subject to excessive oral hygiene requirements as with «traditional» implants. Even smokers are eligible for treatment and can be treated with the

same chances for success as all other patients.

THE SYSTEM THAT PLEASES THE SURGICAL AND RESTORATIVE MEMBERS OF THE TEAM Trans-osseous implants let you treat even difficult cases

in the regular dental office (with adequate surgical equipment). Hospital stays, bone transplants (in as much as their only purpose is to create a suitable

implant bed for screw implants) etc. can be avoided.

EXPAND YOUR RANGE OF THERAPEUTIC OPTIONS, AND OFFER SOLUTIONS IN THE FOLLOWING SITUATIONS

- Morate to severe atrophy - Bone augmentation and sinus lift procedures

- Implant loss - Scheduled bone graft procedures

- Periodontal involvement - After implant losses, for rescuing cases

- Nicotine abuse

IMPLANT NOMENCLATURE EXAMPLE: BBBS

COI / Diskos® Cementing head (large/small)

X Disk spacing 5 mm for double-disk implants

(without «X»: 3 mm disk spacing)

One-piece COI implants

B Single-disk COI implants

BB Double-disk COI implants

BBB Triple-disk COI implants

10 Implant diameter (in mm, basal disk)

7 Implant diameter (in mm, maximum width)

(anatomical shaped basal implants, with

disk rings in different diameters)

H Shaft height in mm

Implant material (unless otherwise mentioned): CP Grade 2 titanium. In the case where our implants are placed in the craniofacial or maxillo-

facial area, e.g. for the fixing of epitheses, this may only be done by maxillofacial or craniofacial surgeons.

Other classification elements

S Cube-shaped disks (e.g. BS 12)

A Asymmetrical shaft (e.g. BAST)

CSD Cutter shaft diameter

SH3

SH2

SH1

SH 1-3 Disk height (individual disks)

SA Distance between disks

{FSA

SA

COI / DISKOS / BECES

We make implant treatment safe!

26

CUT TER SEQUENCES

VC 1.9 * LCXD9 (LC9-6W) (LC12-6W)

VC 1.9 * LCT7

(KCT7)

LC8-4W - (3x) (LC7-6W)

XBBS

BBBS

VC 1.9 * KC7

LC7-6W

LC9 -6W (LC 10-4W mandible)

VC 1.9 * LCD7 LC9-6W

VC 1.9 * LCD7 LC10 LC10

BBS 10

BBS 7/9

BS 9 BAST 9/16

Bone

1.1 CUTTER SEQUENCES

* If necessary, pre-cut with a carbide bur. An angled handpiece can alternatively be used if desired.

BAC 9/33

VC 1.9 * KC7

LC7-6W

LC9 -6W (LC 10-4W mandible)

Bone

Bone

Bone

Bone

Bone

High-speed /

Turbine

Angled handpiece

27

1.2 VERTICAL OSTEOTOMY

Caution: Structures at risk must be protected.

Angled handpiece speed: up to 200,000 rpm

Turbine speed: up to 40,000 rpm

Use external irrigation/aerosol only.

Diameter at the working tip

VC: 1.6 mm (high-speed contra-angle/turbine)

VCW: 1,9 mm (angled handpiece)

Angled/high-speed handpiece

VC/VCW cutter

1.3 HORIZONTAL OSTEOTOMY

1. Para-crestal flap (lingual/palatal).

2. Determine the starting points (A or B ) and the endpoints (A or B) of the vertical osteotomy (see 1.3).

3. Establish the depth of the vertical osteotomy : In the distal mandible, insert near the linea obliqua or below.

4. Carry out the vertical osteotomy (see 1.2, 1.3).

5. Carry out the horizontal osteotomies with the appropriate cutter sequence.

6. Disinfect with betadine and close sutures tightly.

7. Suture tightly closed using silk suture (pull flap over abutment).

8. External fixation (splinting by the prosthetic restoration) no later than the third day postoperatively; the bridge-splinting

will be left in place for at least six months.

9. Points „A“ and „B“ are starting points or end-points of the vertical osteotomy.

SURGERY

B

A

A

B

Linea obliquaLinea obliqua

(4) (4)

d handpiece

High-speed

Linea obliquaLinea obliqua

(5) (5)

28

1.4 MULTI-DISK COI IMPLANTS

Establish the position of the disks within the bone depending

on the disk space spacing (3 mm or 5 mm)

1.5 SINGLE-DISK COI IMPLANTS

Select the right cutter sequence for the prevailing bone

quality.LC = lateral cutter

KC = combination cutter

1.6 INSERT THE IMPLANT

Always choose the maximum possible disk Ø.

Apply KNO insertion chisel or a second

elevator to the disk ring or the horizontal

strut of the implant. Make sure never to

damage the polished vertical part of the

implant.

1.7 PUNCH THE FLAP WITH THE SCALPELL AND PULL THE FLAP OVER THE ABUTMENT

Suture the gingiva in place (e.g. using 3.0 silk sutures)

1.8 IMPRESSION

Caution: Use only medium-flow silicones (no putty), alginate

or polyether.

Do not use thin-flowing silicones. Do not use the double-

mixing technique, nor correction technique. TS5

COI implant

1.9 INSERT IMPLANT ANALOGUE INTO THE IMPRESSION

After inserting the implant analogs, the impression is poured

in gypsum. IAB M

TS5

SURGERY

3 mm 3 mm

3 mm

5 mm

LCD

LCT

KCT LCDX

KNO: Bone- and insertion chisel

29

COI-IMPLANTS

COI BS

COI BAST (REPLACES BAS)

COI BBS

COI BBBS

One-piece implants with longitudinal oval threaded pin (1.95 mm x 2.1 / 2.3 mm Ø); height of the implant head, 7.2 mm;

width of the implant head, 3.9 mm; sandblasted head.

Description SH1 REF Price cat.

BS 7 H8 0.7 - 0.9 13-461621 N

BS 7 H12 0.7 - 0.9 13-461622 N

BS 9 H6 0.7 - 0.9 13-461623 N

BS 10 H4 0.7 - 0.9 13-461624 N

BS 10 H6 0.7 - 0.9 13-461625 N

BS 10 H10 0.7 - 0.9 13-461626 N

BS 12 H6 0.7 - 0.9 13-461627 N

BS 12 H8 0.7 - 0.9 13-461628 N

BS 12 H10 0.7 - 0.9 13-461629 N

BS 12 H12 0.7 - 0.9 13-461630 N

• Cube-shaped disks (anti-rotational)

• GD = Maximum diameter on round side

• With cogs on the flat side

• May be rotated after placement

Description SH GD REF Price cat.

BAST 10 /16 H4 0.7 - 0.9 10 13-461647 T

BAST 10 / 12 H6 0.7 - 0.9 10 13-461642 T

BAST 10 / 16 H6 0.7 - 0.9 10 13-461643 T

BAST 10 / 14 H8 0.7 - 0.9 10 13-461646 T

BAST 10 / 16 H8 0.7 - 0.9 10 13-461644 T

Description SH1 SH2 F SA REF Price cat.

BBS 7 H6 0.7 - 0.9 0.7 4.4 3 13-461655 Q

BBS 9 / 7 H6 0.7 - 0.9 0.7 4.4 3 13-461656 Q

BBS 9 / 7 H10 0.7 - 0.9 0.7 4.4 3 13-461657 Q

BBS 9 / 7 H8 0.7 - 0.9 0.7 4.4 3 13-461658 Q

BBS 10 H4 0.7 - 0.9 0.7 4.4 3 13-461659 Q

Description SH1 - SH3 F SA REF Price cat.

BBBS 7 H4 0.6 7.8 3 13-461652 N

BBBS 7 H6 0.6 7.8 3 13-461653 N

BBBS 7 H8 0.6 7.8 3 13-461654 N

COI IMPLANTS

30

COI IMPLANTS & ACCESSORIES

IMPRESSION AND LAB ACCESSORIES FOR COI AND BECES® ≥ 5.5 MM Ø

Code

REF

TSPA 5 (plastic)

13-462030

Impression post

Internally round

Pack of 5

IA B (plastic)

13-462106

Analogue

Pack of 5

scanable

IA4/IAU (metal)

13-462112

Double-analogue

IA4/IAU (plastic)

13-462111

Double-analogue

Pack of 5

POB

13-462086

Castable part

Pack of 5

Price cat. B B A B B

BENDING AID FOR COI IMPLANTS

COI XBBS

COI BAC

COI BAC2

BREAK-OFF BONE SCREWS FOR SECURING BASAL IMPLANTS


BHB Flexing aid for BOI® implants, use with RAT2 13-462700 B

Description SH1 SH2 F SA REF Price cat.

XBBS 12 / 9 H6 0.7 - 0.9 0.7 6.4 5 13-461674 T

XBBS 14 / 10 H8 0.7 - 0.9 0.7 6.4 5 13-461676 T

• For the upper canine region


SSFW 6 Break-off bone screw, short (6 mm), purple, pack of 5 13-401570 B

SSFW 9 Break-off bone screw, long (9 mm), blue, pack of 5 13-401572 B

Note: After securing the screw, the angled handpiece connector part is broken off through careful lateral

movements. Thread diameter: 1.1 mm


COI BAC 9/33 H4 0.6 461662 X

COI BAC 9/33 H6 0.6 461660 X

• In severely atrophied areas

• As a subperiosteal implant

• Use in combination with fibrin membranes (PRF)

• Retaining screws: SSF 2.4 or SSF 2.7


COI BAC2 9/43 H4 0.6 461666 X

COI BAC2 9/43 H6 0.6 461667 X

COI BAC2 9/43 H8 0.6 461668 X

31


SSF BONE SCREWS

Description Piece / Pack ø L REF Price cat.

SSF 1.5 6 5metallic silver

1.5 6 13-401500 B

SSF 1.5 8 5 1.5 8 13-401502 B

SSF 2.4 6 5

anodized yellow

2.4 6 13-401506 B

SSF 2.4 8 5 2.4 8 13-401508 B

SSF 2.4 10 5 2.4 10 13-401510 B

SSF 2.4 12 5 2.4 12 13-401512 B

SSF 2.4 14 5 2.4 14 13-401514 B

SSF 2.7 8 5

anodized blue

2.7 8 13-401558 B

SSF 2.7 10 5 2.7 10 13-401560 B

SSF 2.7 12 5 2.7 12 13-401562 B

SSF 2.7 14 5 2.7 14 13-401564 B

INSTRUMENTS AND TOOLS (STAINLESS STEEL)

Description Code REF Price cat.

Titanium spatula, 17 cm, individually bendable

and grindable, Grade 1 titaniumTIS 13-425407 B

Bone and insertion chisel, 13 cm long,

custom-grindableKNO 13-462330 B

Screwdriver tip for

contra-angle and adapter

36 mm long

ITW SSF 13-314448 C

Adapter for all angled handpiece instruments, matches handle 13-310530 C

Handle/handgrip, 110 mm long (snap-on connection) 13-311431 V

Screwdriver tip, 100 mm long,

for direct insertion into the handgrip13-314447 C

Drill for SSF-bone screws, 1.4 mmd SDW SSF 13-310520 C

Hex-Instrument extralong, 45 mm, Ø 1.25 mm HTX 1.25 EO 13-462372 K

Gabelschlüssel for HT 1.25 EO and HTX 1.25 EO HAS 13-463108 H

Ratchet, angled

for all Hex-instruments and insertion toolsRAT3 13-425050 S

32

DISKOS® 4D IMPLANTS

ONE-PIECE BASAL IMPLANTS WITH TSD4-HEAD

High primary stability is achieved through turning of the the vertical implant part.

DISKOS® 4DS


4DS 12 H4 13-461112 T

4DS 12 H6 13-461113 T

4DS 12 H8 13-461114 T

4DS 10 H6 13-461121 S

4DS 10 H8 13-461122 S

4DS 9 H4 13-461115 S

4DS 9 H6 13-461116 S

4DS 9 H8 13-461117 S

DISKOS® 4DDS

Description SH1 SH2 F REF Price cat.

4DDS 7 H7 0.6 0.6 4.2 13-461118 S

DISKOS® 4DDDS

Description SH1 SH2, SH3 F REF Price cat.

4DDDS 7 H4 0.7–0.9 0.7 8.0 13-461119 X

4DDDS 7 H6 0.7–0.9 0.7 8.0 13-461120 X

DISKOS® T4

Description SH1-SH3 F SA REF Price cat.

4T 5/7 H2 0.6 7.8 3 13-461899 N

4T 5/7 H3 0.6 7.8 3 13-461900 N

4T 5/7 H4 0.6 7.8 3 13-461901 N

• For immediate loading, including with SSF, use bone screws or SSFW drive screws. Cutters: ICT5, ICT5-N

• For single-tooth replacement in the incisal and premolar areas

• For longitudinal or oblique insertion

• Use impression- and lab-parts from the KOC-System (small head)

Impression and laboratory accessories for Diskos®, 4D, T4

Code

REF

TSPA 4

13-462029

TSKPA 4

13-462028

IAK M IA4SM

13-462110 13- 462103

IA4/IAU

13-462111

IA4/IAU

13-462112

PO4

13-462088

internally round

castable

internal edges

castable

Height of head 6.5 mm

with 5 sleeves

Double-analogue

(plastic)

Double-analogue

(metal)internally round

Pack of 5 Pack of 5 scannable Pack of 5 Pack of 5

Price cat. A A B A A A A

or

M

or

M

or

33

VERTICAL AND HORIZONTAL CUT TER

CUTTER FOR COI AND DISKOS® IMPLANTS

CUTTER FOR DISKOS®4T - IMPLANTS

VERTICAL CUTTER (VC)

COMBINATION CUTTER SIMULTANEOUS CUTTING ON VERTICAL AND HORIZONTAL PART

Description L DV ** REF Price cat.

VC 1.9 * 32 1.9 13-462214 F

VC 1.6 * 32 1.6 13-462215 F

VC 1.9-W *** 1.9 13-462214-W F

* FG for turbine or red contra-angle / ** DV = Diameter Vertikalcutter / *** for contra-angle

Description L SH SA D REF Price cat.

KC 7-4W 32 0.4 7 13-462221-4W E

KCD 7-4W 32 0.4 3 7 13-462237-4W E


ICD5-N 26.7 0.6 3 5 13-462437-W D

ICT5-N 30.3 0.6 3 5 13-462415-W D

L = length in mm / SH = disk height / SA = disk spacing / D = disk diameter

KCD Kombi Double Cutter WstKCD Kombi Double Cutter Wst

ICD CutterICD CutterICD C tter

ICT CutterICT Cutter


LC 7-6W 32 0.6 7 13-462259-6W D

LC 8-4W 32 0.4 8 13-462260-4W E

LC 9-6W 32 0.6 9 13-462261-6W E

LC 10-4W 32 0.4 10 13-462262-4W ELC 7 Lateral Cutter WstLC 7 Lateral Cutter Wstl

LATERALCUTTER CUTS ONLY AT THE DISC

INTERNATIONAL IMPLANT FOUNDATION PUBLISHING

This book shows how a great increase in productivity in dental implantology can be achieved at the same time as a gain in treatment safety.

These gains can be utilised in several ways:

• to increase the number of patients treated

• to increase practice turnover / time units

In any event the quality of life of the treated patient is increased.

Making the fullest use of this technology means saying goodbye to most of the previous

“rules“ of dental implantology and opening your mind to the new treatment options.

The rules of «basal implantology» have always been valid, and in principle they are easy

to understand. However, the possibilities of the procedure described here have so far

been recognised by only a few practitioners, and its practical application has not been

described cohesively until now.

2. REVISED EDITION


Immediate Loading, russian version 4456 P

Immediate Loading, englisch version 4445 P

Simpladent GmbH Phone +41 (0)55 293 23 70

Dorfplatz 11 [email protected]

CH - 8737 Gommiswald / SG www.simpladent-implants.com

PLEASE CHECK THE VALID PRICE LIST OF YOUR LOCAL COORDINATOR

Symbols on the packs

COI implants may be inserted and serviced only by qualified personnel with valid authorization by the manufacturer (pursuant to legislation on the

installation, use and maintenance of medical devices).

We are certified DIN EN ISO 13485, and annex II of EEC Directive 93/42 EWG (2007).

The product dimensions shown in this catalogue may be different from actual reality for technical reasons.

Diskos® isa registered trademark. Diskos® implants are protected by patents.

In case that implants would be reprocessed (cleaned, resterilized) infections could occur, because no validated procedures for reprocessing are avail-

able in the dental office.

KOC® Micro

KOC® MicroD

KOC® MU

Application in

healed bone areals

Application in fresh

extraction sockets

KOC® Plus

1st cortical

2nd cortical

BECES® BECES® MU

0029REF Single_piece_SAP_EN_V034-12/15

Production

No.

Sterilized by

gamma radiation

Sterilization

Ethylene oxide

Single-

use

product

Instruction

for use

Expiry date Store

in a dry

place

Temperature

range from

-5° C to 25° C

Store tightly

keep closed

Do not use if

packing is

damaged

Do not

resterilize

Manu-

facturer

-5° C

25° C

Rx ONLYNon-

sterile

Intended for use by

dentists or surgeons

only

Production

date

simpladent single piece sap en v036...1. have your laboratory produce a drilling template with the...

Documents