side-view cut-out display panel state indicator€¦ · (mm) s ry1 ry2 ry3 ry4 max r/t ~a 16 17 18...
TRANSCRIPT
SIDE-VIEW CUT-OUT
DISPLAY PANEL
KEYS
STATE INDICATOR
SIDE-VIEW CUT-OUT
DISPLAY PANEL
KEYS
STATE INDICATOR
SIDE-VIEW CUT-OUT
DISPLAY PANEL
KEYS
STATE INDICATOR
MMG Modbus-RTU Digital Meter AC&M
Set as MASTER or SLAVE mode
Suitable for Modbus RTU instruments
Programmable address for data write and data read
Data form: Unsigned Int / Signed Int
Write data:06H 16H
Max.Baud rate: 38400
Address:1 ~ 255
With analog output and alarm setting
MMG..- .. - - -
Code 1 Input Signal Code 2 Alarm Setting Code 3 Output Code 4 Aux. Power
1 RS-485 2 2 Alarm Setting 1 DC 0~10mA 1 AC 110/220V
2 RS-232 4 4 Alarm Setting 2 DC 0~20mA 2 AC 220V
3 RS-485+232 0 None 3 DC 4~20mA 3 DC 22~72V
4 RS-422 4 DC 0~5V 6 AC/DC 85~265V
5 Ethernet 5 DC 1~5V Y Other
6 Other 6 DC 0~10V
0 None
Y Other
INPUT:
Display Range 0.56" High brightness RED LED,5 Digits. Unsigned Int:0~65535 Counts. Signed Int:-32767~32767 Counts..
Input Frequency 45 400Hz.
Response Time 200 msec
Mode Master or Slave
Communication Protocol Modbus RTU
Baud rate 4800-9600-19200-38400 (programmable)
Address 1~255
Parity Check NONE-ODD-EVEN (programmable)
Stop Bit 1 or 2 (programmable)
Data Bit 8 bit
Data Form Unsigned Int / Signed Int
Parity Check NONE-ODD-EVEN (programmable)
Stop Bit 1 or 2 (programmable)
OUTPUT & DISPLAY:
DC Current: 0 – 20 mA DC DC Voltage: 0 – 10 V DC
Load resistance drive: output drive 10 VDC maximum Load resistance drive: output drive 5 mA maximum
Output Load Resistance Output Load Resistance
0 – 10 mA :
0 – 20 mA :
4 – 20 mA :
1000
500
500
0 – 5 V :
1 – 5 V :
0 – 10 V :
1 K
1 K
2 K
INSTALLATION & PERFORMANCE:
Alarm Setting 2 or 4 Alarm Setting, Setting Function(Hi or Lo) User Selectable.
Setting Range -19999 99999 Counts User Selectable.
Dead Band 0 9999 Counts User Selectable.
Time Delay 0 999 Sec. User Selectable.
SPDT Capacity AC 120V 3A,, DC 30V 3A.
Dielectric Strength 2KV AC / Min Between Input / Power / Case.
Operating Condition 10 55 20 95% RH Non-Condensed.
Storage Condition 40 75 20 95% RH Non-Condensed.
Consumed Power 3VA , PF = 1
Power Supply AC or DC ±20%, 50 / 60Hz.
Outline Dimension 1/8 DIN 96W X 48H X 100D mm.
Mounting Panel Flush Mounting. VER:20120420
Code 1
Code 2
Code 3
Code 4
(mm)
S
RY1 RY2 RY3 RY4 MAX R/T A~
+ + +
16 17 18 22 23 24POWER
NO COM NC NO COM NC NO COM NC NO COM
RS-485
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
+ - GND 110V 220V0V
DC power 23+ ; 24-
RY1 RY2 RY3 RY4+ -
Analog+ -
2
7
1
6 98
3 4 5
RS 485 RS232
SIDE-VIEW CUT-OUT
DISPLAY
SATE INDICATOR
PANEL KEYS
MASTER MODE
Read display value of PM100 or other instruments.
Via RS 485 or Ethernet.
MMG PM100
SLAVE MODE
Use Modbus 06H 16H to write parameters Unsigned Int or Signed Int to MMG
Via RS 485 or Ethernet
PC/PLC….. MMG
MMQ Var Digital Meter A C&M FETURES
Suitable for 1∮2W / 1∮3W / 3∮3W / 3∮4W system
Size: 96 W x 48 H x 100 D (mm) 5 Digit display: -32768~32767 Count
Optional RS-485 Modbus RTU Optional DC 4~20mA output Bi-direction measurement and display
FUNCTION SELECTION
MMQ - code1 code2 code3 code4 code5 code6 CODE 1
INPUT VOLTAGE
CODE 2
INPUT CURRENT
CODE 3
INPUTFREQUENCY
CODE 4
OUTPUT 1
CODE 5
OUTPUT 2
CODE 6
AUX. POWER
1 55-440V(L-L) 1 1A 1 50 HZ 1 2Alarm 1 RS-485 3 DC 22~72V 2 5A 2 60 HZ 3 DC 4~20mA ModbusRTU 6 AC/DC85~265V 0 None 0 None Y Other Y Other Y Other Y Other Y Other Y Other SPECIFICATIONS
Accuracy :±0.5%RD at 23 ±3℃ ℃ Display Range :0.4"High brightness red LED 5-digit -32768~32767 Input Range :Input 55~440V(L-L) ( Max: 500V L-L )
Normal Current 5A, Effective Range 0~6A Normal Current 1A, Effective Range 0~1.5A.
Input Burden :Voltage0.25VA ; Current0.2VA@50/60Hz Input Frequency :45~70HZ Input Over :Normal AC 5A, Current Over 15A Continuous Normal AC 440V,Voltage Over 600V Continuous Digital Output Load:RS-485 MODBUS RTU Baudrate :2400.4800.9600.19200.38400.57600 Address :1~255
Output Function :4~20mA330Ω at 20ma (Optional) Alarm Function :2Alarm Setting (Optional)
Dielectric Strength :2.0KV 50/60HZ AC / Min Between Input / Power / Case.
Power Supply :AC 85~265V 50 / 60Hz DC 100~300V Dimension :96 W X 48 H X 100 D mm. Cut-out :92W x 44H < mm > Mounting :Panel Flush Mounting Housing Material :ABS Plastic, Self-Extinguishing Operating Condition:-10 ~55 20 ℃ ℃ ~ 95% RH Non-Condensed. Storage Condition :-40 ~75 20 ℃ ℃ ~ 95% RH Non-Condense
SIZE (mm)
VarH
P1/2
MMQ Var Digital Meter A C&M TERMINALS
+16
R S T N 1
1K
2 3 4 5 6 7 8 9 10 11 12 1 3 14 1 5 R S 4 85 A B G P u lse 1 2 C om
+17
+18
+19
+20
+21
P W + P W -
22 23 24
1L 2K 2L 3K 3LC u rren t In p u t
V o lta ge In p u t A la rm 1 A larm 2
CONNECTION DIAGRAM
2 L1 K 1 L 2 K R3 K 3 L S T
單 相 二 線 (1 P 2 W )N
L 1
N
L O A D
1 71 6 2 01 8 1 9 2 1 1 32 4
電 壓 及 電 流 輸 入 I N P U T V o lta g e a n d C u r r e n t
以 上 接 線 必 須 配 合 輸 入 模 式 設 定
2 L1 K 1 L 2 K 3 K 3 L
單 相 三 線 (1 P 3 W )N
L 1 L O A D
L 2
2 L1 K 1 L 2 K 3 K 3 L
三 相 四 線 (3 P 4 W )
L 2L 1 L O A D
L 3N
2 L1 K 1 L 2 K 3 K 3 L
三 相 三 線 (3 P 3 W 2 C T )L 2L 1 L O A D
L 3
2 L1 K 1 L 2 K 3 K 3 L
三 相 三 線 (3 P 3 W 3 C T )L 2L 1 L O A D
L 3
輔 助 電 源 & 輸 出
A B6 87
4 8 5 O /P9 1 11 0
P u ls e O /P
G N D C H 1 C H 2 C O M2 2 2 3 2 4
R S T N1 71 6 2 01 8 1 9 2 1 1 32 4
R S T N1 71 6 2 01 8 1 9 2 1 1 32 4
R S T N1 71 6 2 01 8 1 9 2 1 1 32 4
R S T N1 71 6 2 01 8 1 9 2 1 1 32 4
P W + P W -
P O W E R
P2/2
SIDE-VIEW CUT-OUT
DISPLAY PANEL
KEYS
STATE INDICATOR
SIDE-VIEW CUT-OUT
DISPLAY PANEL
KEYS
STATE INDICATOR
SIDE-VIEW CUT-OUT
DISPLAY PANEL
KEYS
STATE INDICATOR
MMV AC Voltage Digital Meter AC&M
Programmable PT ratio
Output: 0-20mA/4-20mA or 0-5V/1-5V/0-10V
RS 485 MODBUS RTU and 4 Alarm Setting Function
Small size (Depth< 90mm)
Selectable Sampling Speed: (High/Medium/Low)
*Sampling speed is determined by the buffer size.
Buffer size=The number of measurements for RMS.
MMV ..- .. - - - R.M.S
MMVR . . .- .- - - T.R.M.S
Code
1 Input Current
Code
2 Alarm Setting
Code
3 Output 1
Code
4 Output 2
Code
5 Aux. Power
1 AC 0-440V 2 2 Alarm Setting 1 DC 0~10mA 6 RS 485 1 AC 110/220V
4 4 Alarm Setting 2 DC 0~20mA 0 None 2 AC 220V
Y Other 0 None 3 DC 4~20mA Y Other 3 DC 22~72V
4 DC 0~5V 6 AC/DC 85~265V
5 DC 1~5V Y Other
6 DC 0~10V
0 None
Y Other
INPUT:
Input Frequency 45 70Hz.
Input Burden 0.25VA at 60Hz.
Input Over Normal AC 440V(Max: AC 500V), Over voltage 600V Continuous. 1.2KV 10sec/Hr
OUTPUT & DISPLAY: DC Current: 0 – 20 mA DC DC Voltage: 0 – 10 V DC Load resistance drive: output drive 10 VDC maximum Load resistance drive: output drive 5 mA maximum
Output Load Resistance Output Load Resistance
0 – 10 mA :
0 – 20 mA :
4 – 20 mA :
1000
500
500
0 – 5 V :
1 – 5 V :
0 – 10 V :
1 K
1 K
2 K
Output Response Time 1 Sec. ( programmable per 100ms/unit )
Output Protection Without Damage for Output Open or Short Circuit.
Digital Output RS-485 Output, 1200,2400,4800,9600,19200 Baud Rate, User Selectable.
Display Range 0.56" High brightness RED LED , 5 Digits, -19999 ~ 99999Counts..
INSTALLATION & PERFORMANCE:
Accuracy 0.15%FS+1 Counts. Avg. Typically at 23 3 . 0.25%FS+1 Counts. TRMS Typically at 23 3 .
Setting Function 4 Alarm Setting, Setting Function(Hi or Lo) User Selectable.
Setting Range -19999 99999 Counts User Selectable.
Dead Band 0 9999 Counts User Selectable.
Time Delay 0 999 Sec. User Selectable.
SPDT Capacity AC 120V 3A,, DC 30V 3A.
Dielectric Strength 2KV AC / Min Between Input / Power / Case.
Impulse 5 KV 1.2x50 uS, ANSI C37.90a / 1983.DIN IEC 255 4.
Stability 0.2%/Year.
Temperature Coefficient 60ppm / From 0 60 50ppm/25 ±5
Operating Condition 10 55 20 95% RH Non-Condensed.
Storage Condition 40 75 20 95% RH Non-Condensed.
Consumed Power 3VA , PF = 1
Power Supply AC or DC 20%, 50 / 60Hz.
Outline Dimension 1/8 DIN 96W X 48H X 100D mm.
Mounting Panel Flush Mounting.
Code1 Code2 Code3 Code4
Code1 Code2 Code3 Code4
Code5
Code5
(mm)
S
RY1 RY2 RY3 RY4 MAX R/T A~
+ + + + + +16 17 18 19 20 21 22 23 24
POWER
NO COM NC NO COM NC NO COM NC NO COM
RS-485
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
INPUT
+ - 110V 220V0V
DC power 23+ ; 24-
RY1 RY2 RY3 RY4+ -
Analog+ -
NO.20120302
SIDE-VIEW CUT-OUT
Display Screen
Keys
State Indicator
MMW Watt Digital Meter A C&M FETURES
Suitable for 1∮2W / 1∮3W / 3∮3W / 3∮4W system
Size: 96 W x 48 H x 100 D (mm) 5 Digit display: -32768~32767 Count
Optional RS-485 Modbus RTU Optional DC 4~20mA output Bi-direction measurement and display
FUNCTION SELECTION
MMW - code1 code2 code3 code4 code5 code6 CODE 1
INPUT VOLTAGE
CODE 2
INPUT CURRENT
CODE 3
INPUTFREQUENCY
CODE 4
OUTPUT 1
CODE 5
OUTPUT 2
CODE 6
AUX. POWER
1 55-440V(L-L) 1 1A 1 50 HZ 1 2 Alarm 1 3 DC 22~72V 2 5A 2 60 HZ 3 DC 4~20mA
RS-485 ModbusRTU 6 AC/DC85~265V
0 None 0 None Y Other Y Other Y Other Y Other Y Other Y Other SPECIFICATIONS
Accuracy :±0.5%RD at 23 ±3℃ ℃ Display Range :0.4"High brightness red LED 5-digit -32768~32767 Input Range :Input 55~440V(L-L) ( Max: 500V L-L )
Normal Current 5A, Effective Range 0~6A Normal Current 1A, Effective Range 0~1.5A.
Input Burden :Voltage0.25VA ; Current0.2VA@50/60Hz Input Frequency :45~70HZ Input Over :Normal AC 5A, Current Over 15A Continuous Normal AC 440V,Voltage Over 600V Continuous Digital Output Load:RS-485 MODBUS RTU Baudrate :2400.4800.9600.19200.38400.57600 Address :1~255
Output Function :4~20mA330Ω at 20ma (Optional) Alarm Function :2Alarm Setting (Optional)
Dielectric Strength :2.0KV 50/60HZ AC / Min Between Input / Power / Case.
Power Supply :AC 85~265V 50 / 60Hz DC 100~300V Dimension :96 W X 48 H X 100 D mm. Cut-out :92W x 44H < mm > Mounting :Panel Flush Mounting Housing Material :ABS Plastic, Self-Extinguishing Operating Condition:-10 ~55 20 ℃ ℃ ~ 95% RH Non-Condensed. Storage Condition :-40 ~75 20 ℃ ℃ ~ 95% RH Non-Condense
SIZE (mm)
KWH
P1/2
MMW Watt Digital Meter A C&M TERMINALS
+16
R S T N 1
1K
2 3 4 5 6 7 8 9 10 11 12 1 3 14 1 5 R S 4 85 A B G P u lse 1 2 C om
+17
+18
+19
+20
+21
P W + P W -
22 23 24
1L 2K 2L 3K 3LC u rren t In p u t
V o lta ge In p u t A la rm 1 A larm 2
CONNECTION DIAGRAM
2 L1 K 1 L 2 K R3 K 3 L S T
單 相 二 線 (1 P 2 W )N
L 1
N
L O A D
1 71 6 2 01 8 1 9 2 1 1 32 4
電 壓 及 電 流 輸 入 I N P U T V o lta g e a n d C u r r e n t
以 上 接 線 必 須 配 合 輸 入 模 式 設 定
2 L1 K 1 L 2 K 3 K 3 L
單 相 三 線 (1 P 3 W )N
L 1 L O A D
L 2
2 L1 K 1 L 2 K 3 K 3 L
三 相 四 線 (3 P 4 W )
L 2L 1 L O A D
L 3N
2 L1 K 1 L 2 K 3 K 3 L
三 相 三 線 (3 P 3 W 2 C T )L 2L 1 L O A D
L 3
2 L1 K 1 L 2 K 3 K 3 L
三 相 三 線 (3 P 3 W 3 C T )L 2L 1 L O A D
L 3
輔 助 電 源 & 輸 出
A B6 87
4 8 5 O /P9 1 11 0
P u ls e O /P
G N D C H 1 C H 2 C O M2 2 2 3 2 4
R S T N1 71 6 2 01 8 1 9 2 1 1 32 4
R S T N1 71 6 2 01 8 1 9 2 1 1 32 4
R S T N1 71 6 2 01 8 1 9 2 1 1 32 4
R S T N1 71 6 2 01 8 1 9 2 1 1 32 4
P W + P W -
P O W E R
P2/2