sediments in the tema harbour (ghana): chemical pollution
TRANSCRIPT
Thesis committee
Promotor
Prof. Dr Piet N.L. Lens
Professor of Environmental Biotechnology
IHE Delft Institute for Water Education, the Netherlands
Co-promotor
Prof. Elvis Nyarko
Professor of Marine Environmental Science
University of Ghana, Accra, Ghana
Other members
Prof. Dr Karen J. Keesman, Wageningen University & Research, the Netherlands
Prof. Kerstin Kuchta, Technical University of Hamburg, Germany
Dr Elin Vanlierde, Agentschap Informatie Vlaanderen, Brussels, Belgium
Dr Leonard Ost, Deltares, Delft, the Netherlands
This research was conducted under the auspices of the Graduate School for Socio-Economic
and Natural Sciences of the Environment (SENSE)
Sediments in the Tema Harbour (Ghana): chemical pollution and sedimentation rates
Thesis submitted in fulfilment of the requirements of
the Academic Board of Wageningen University and
the Academic Board of the IHE Delft Institute for Water Education
for the degree of doctor
to be defended in public
on Friday, 29 June 2018 at 01:30 p.m.
in Delft, the Netherlands
by Benjamin Osei Botwe
Born in Accra, Ghana
CRC Press/Balkema is an imprint of the Taylor & Francis Group, an informa business
© 2018, Benjamin O. Botwe
Although all care is taken to ensure integrity and the quality of this publication and the
information herein, no responsibility is assumed by the publishers, the author nor IHE Delft
for any damage to the property or persons as a result of operation or use of this publication
and/or the information contained herein.
A pdf version of this work will be made available as Open Access via
http://repository.tudelft.nl/ihe. This version is licensed under the Creative Commons
Attribution-Non Commercial 4.0 International License,
http://creativecommons.org/licenses/by-nc/4.0/
Published by:
CRC Press/Balkema
Schipholweg 107C, 2316 XC, Leiden, the Netherlands
www.crcpress.com – www.taylorandfrancis.com
ISBN ISBN: 978-1-138-32351-3
ISBN ISBN: 978-94-6343-838-4 DOI: https://doi.org/10.18174/443802
vii
Acknowledgements
I wish to express profound gratitude to the Dutch Government for funding this PhD study at
the UNESCO-IHE Institute for Water Education in Delft through Nuffic in the framework of
the Netherlands Fellowship Programme (NFP-PhD. 12/316). I also wish to thank the
University of Ghana for the financial support provided through the Office of Research,
Innovation and Development (ORID) under the Faculty Development Fund (UGFD/7/2012-
2013/004). The logistical and technical assistance provided by the Ghana Ports and Harbours
Authority is also acknowledged.
I am most grateful to Prof. dr. Piet N.L. Lens (Promotor) and Prof. Elvis Nyarko (Co-
Promotor), whose excellent guidance and advice have brought me this far. The staff of the
Department of Marine and Fisheries Sciences at the University of Ghana are acknowledged
for their support.
I am also indebted to Alisa Mast and Gregory A. Wetherbee, both at the US Geological
Survey, for donating a KB corer for my field sampling. I also wish to thank Jolanda Boots
(Admissions Officer, UNESCO-IHE, Delft), who was instrumental in the technical matters of
my PhD study at the UNESCO-IHE, Delft. Professor Ronny Blust is acknowledged for
permitting me to conduct bioassay experiments at the Systemic Physiological and
Ecotoxicological Research (SPHERE) laboratory of the University of Antwerp, Belgium. I
received lots of encouragements from Frank and Ida van der Meulen and Cor Schipper for
which I am grateful. My dear wife Janet Botwe, my brother Dr. Theophilus Botwe and my
entire family are also acknowledged for their support. Furthermore, I am grateful to Mr.
Bennet Atsu Foli for providing editorial assistance. Several others have contributed to the
success of my PhD work in one way or the other, whose names are not mentioned.
ix
Abstract
The Tema Harbour in Ghana has been in operation for nearly six decades and is subject to
large influxes of sediments and sediment pollution due to the intense human activities in the
harbour area. This thesis assessed sediment pollution in the Tema Harbour by using the
standard 10-day Corophium volutator and 28-day Hediste diversicolor whole-sediment
toxicity bioassays as well as chemical contaminant (DDTs, HCHs, PAHs and metal - Cd, Pb,
Cr, Ni, Cu, Zn and As) data. The bioassay results showed significant C. volutator and H.
diversicolor mortalities, indicating that the Tema Harbour sediments are polluted and toxic.
Biota-sediment accumulation factors further revealed a high potential for bioaccumulation of
the sediment-associated metals, which can have adverse implications for the food chain. Thus,
the Tema Harbour sediments are unsuitable for disposal at sea without remediation.
The thesis further investigated sediment accumulation rates (SARs) in the Tema Harbour by
the combined analyses of sediment trap and sediment core data. The sediment cores exhibited
variable bulk density profiles, indicating highly dynamic and non-steady sedimentation
conditions. 7Be-derived gross-estimates of very recent sediment accumulation rates using the
constant flux-constant sedimentation (CF-CS) model were in the range of 2.5-9.0 g.cm-2
.y-1
.
These values were much lower than the estimated average settling fluxes from the sediment
trap data (15.2-53.8 g.cm-2
.y-1
), indicating sediment resuspension plays an important role in
the sedimentation process. Conventional 210
Pb sediment dating models did not allow any
estimation of SARs in the Tema Harbour. The 210
Pb-based TERESA model, on the other
hand, proved to be a good tool for quantifying sediment accumulation rates in the Tema
Harbour with time-averaged values in the range of 1.4-3.0 g.cm-2
.y-1
and sediment accretion
rates of 1.7-3 cm.y-1
.
In conclusion, this study has shown that the Tema Harbour has been severely affected by
anthropogenic activities, resulting in pollution of the sediments, especially those from the
Fishing Harbour and the Canoe Basin. Moreover, the sediment accretion rates in the harbour
may pose moderate problems for sustainable use of the harbour. There is, therefore, a need to
improve sediment and environmental management in the Tema Harbour and regulate the
disposal of the dredged material originating from this tropical coastal harbour.
xi
Abbreviations and acronyms
AAS – Atomic absorption spectrometer
Ace – Acenaphthene
Acy – Acenaphthylene
AEDE – Annual effective dose equivalent
AGDE – Annual gonadal dose equivalent
AL1 – Action levels 1
AL2 – Action level 2
ANOVA – Analysis of variance
Ant – Anthracene
BaA – Benzo[a]anthracene
BaP – Benzo[a]pyrene
BbF – Benzo[b]fluoranthene
BCR – Community Bureau of Reference
BFR – Brominated flame retardant
BghiP – Benzo[g,h,i]perylene
BkF – Benzo[k]fluoranthene
Bq – Becquerel
BSAF – Biota-sediment accumulation factor
CANMET – Canada Centre for Mineral and Energy Technology
CB – Canoe Basin
Chr – Chrysene
COEC – Chemicals of emerging concern
CRM – Certified reference material
DahA – Dibenz[a,h]anthracene
DDD – Dichlorodiphenyldichlororethane
DDE – Dichlorodiphenyldichloroethylene
DDT – Dichlorodiphenyltrichloroethane
DNA – Deoxyribonucleic acid
DO – Dissolved oxygen
EF – Enrichment factor
Eh – Redox potential
ENEA – Ente per le Nuove tecnologie, l‘Energia e l‘Ambiente
Abbreviations and acronyms
xii
ERL – Effects Range Low
ERLQ – Effects range low quotient
ERM – Effects Range Median
ERMQ – Effects range median quotient
ERICA – Environmental Risk from Ionising Contaminants Assessment and Management
Fla – Fluoranthene
Flu – Fluorene
GC – Gas chromatograph
GC-ECD – Gas chromatograph with electron capture detector
GC-FID – Gas chromatograph with flame ionisation detector
GC-MSD – Gas chromatograph with mass selective detector
GESAMP – Group of Experts on the Scientific Aspects of Marine Environmental Protection
GIS – Geographic Information Systems
GPHA – Ghana Ports and Harbours Authority
Gy – Gray
HCH – Hexachlorocyclohexane
Hex – External hazard index
HPAHs – High molecular weight PAHs
IAEA – International Atomic Energy Agency
ICP – Inductively Coupled Plasma
ICP-MS – Inductively Coupled Plasma - Mass Spectrometry
IFH – Inner Fishing Harbour
Igeo – Geo-accumulation index
IP – Indeno[1,2,3-cd]pyrene
JICA – Japan International Co-operation Agency
LPAHs – Low molecular weight PAHs
MERMQ – Mean effects range median quotient
MH – Main Harbour
MTCA – Model Toxics Control Act
Nap – Naphthalene
NFP - Netherlands Fellowship Programme
NIST – National Institute of Standards and Technology
NTU – Nephelometric Turbidity Unit
NUFFIC - Netherlands Organisation for International Cooperation in Higher Education
Abbreviations and acronyms
xiii
OC – Organochlorine compound
OCP – Organochlorine pesticide
OFH – Outer Fishing Harbour
OM – Organic matter
PAH – Polycyclic aromatic hydrocarbon
PAH16 – 16 priority PAHs by the United States Environmental Protection Agency
210Pbex – Excess Lead-210
210Pbsupp – Supported Lead-210
PBDE – Polybrominated diphenyl ether
PCB – Polychlorinated biphenyl
PCDD – Polychlorinated dibenzodioxins
PCDF – Polychlorinated dibenzofuran
PCN – Polychlorinated naphthalene
PDBS – Phase Differencing Bathymetric Sonar
PFC – Perfluorinated chemical
PFOA – Perfluorooctanoic acid
PFOS – Perfluorooctane sulfonate
Phe – Phenanthrene
POPs – Persistent organic pollutants
ppm – Parts per million
PVC – Polyvinyl chloride
Pyr – Pyrene
RAC – Risk assessment code
Raeq – Radium equivalent activity
RHI – Radiological hazard indices
RSD – Relative standard deviations
SAR – Sediment accumulation rate
SF – Settling fluxes
SPHERE – Systemic Physiological and Ecotoxicological Research laboratory
SPM – Suspended particulate matter
SPSS – Statistical Package for Social Sciences
SQG – Sediment quality guidelines
SRM – Standard reference material
Sv – Sievert
Abbreviations and acronyms
xiv
SWI – Sediment-water interface
T1/2 - Half-life
TBT – Tributyltin
TEF – Toxic equivalency factor
TENORM – Technologically enhanced naturally-occurring radioactive material
TEQ – Total toxicity equivalence
TERESA – Time Estimates from Random Entries of Sediments and Activities
TEU – Twenty-foot equivalent unit
234Thexc – Excess Thorium-234
TN – Total nitrogen
TOC – Total organic carbon
TOR – Tema Oil Refinery
UN – United Nations
UNSCEAR – United Nations Scientific Committee on the Effects of Atomic Radiation
USEPA – United States Environmental Protection Agency
xv
Contents Abbreviations and acronyms ..................................................................................................... xi
Chapter 1 .................................................................................................................................... 1
General Introduction ................................................................................................................... 1
1.1. Background of this study ............................................................................................. 2
1.2. Research approach ....................................................................................................... 4
1.3. Structure of this thesis ................................................................................................. 5
Chapter 2 .................................................................................................................................. 11
Literature Review ..................................................................................................................... 11
2.1. Chemical pollution in coastal marine environments ................................................. 12
2.2. Types and effects of chemical pollutants in coastal marine environments ............... 13
2.3. Sources of chemical pollutants in coastal marine environments ............................... 14
2.4. Fate of chemical pollutants in coastal marine environments ..................................... 15
2.5. Assessment of chemical pollution in coastal marine environments .......................... 17
2.5.1. Inventory of chemical pollutants in sediments .......................................................... 17
2.5.2. Pollutant source apportionment in sediments ............................................................ 19
2.5.2.1. DDT and HCH .................................................................................................... 19
2.5.2.2. PAHs ............................................................................................................... 22
2.5.2.3. Metals ................................................................................................................. 22
2.5.3. Human health and ecotoxicological risk characterisation ......................................... 24
2.5.3.1. Radiological hazard indices and the ERICA model ........................................... 24
2.5.3.2. The Sediment Quality Guideline approach ........................................................ 27
2.5.3.3. The total toxicity equivalence approach ............................................................. 28
2.5.3.4. Using the risk assessment code .......................................................................... 30
2.5.4. Hazard/Toxicity and impact assessment .................................................................... 32
2.6. Sedimentation in harbours ......................................................................................... 35
2.6.1. Sediment fluxes in harbours ............................................................................... 35
2.6.2. Quantification of SFs ................................................................................................. 36
2.6.3. Quantification of SARs .............................................................................................. 37
2.6.3.1. 210
Pb as a tool for the quantification of SARs .................................................... 38
2.7. Conclusions................................................................................................................ 48
Chapter 3 .................................................................................................................................. 73
Contents
xvi
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema
Harbour (Greater Accra, Ghana) .............................................................................................. 73
3.1. Introduction ................................................................................................................ 74
3.2. Materials and Methods .............................................................................................. 76
3.2.1. Description of the study area ..................................................................................... 76
3.2.2. Sediment sampling ..................................................................................................... 76
3.2.3. Sample analyses ......................................................................................................... 78
3.2.4. Radiological risk assessment ..................................................................................... 79
3.2.5. Radioecological risk assessment ................................................................................ 80
3.3. Results and discussion ............................................................................................... 81
3.3.1. Radioactivity levels in the Tema Harbour sediments ................................................ 81
3.3.2. Radiological significance of Tema Harbour sediment specific activity levels .......... 86
3.3.3. Radioecological significance of Tema Harbour sediment radioactivity .................... 88
3.4. Conclusions................................................................................................................ 90
Chapter 4 .................................................................................................................................. 97
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in
Surface Sediments of Coastal Tema Harbour (Ghana) ............................................................ 97
4.1. Introduction ................................................................................................................ 98
4.2. Materials and methods ............................................................................................. 100
4.2.1. Sediment sampling ................................................................................................... 100
4.2.2. Sediment analyses .................................................................................................... 101
4.2.3. Quality assurance and control .................................................................................. 102
4.2.4. Data treatment .......................................................................................................... 102
4.3. Results...................................................................................................................... 104
4.3.1. Sediment physicochemical characteristics .............................................................. 104
4.3.2. Levels and distribution of DDTs and HCHs in the Tema Harbour sediments ........ 104
4.3.3. Levels and distribution of PAHs in the Tema Harbour sediments .......................... 105
4.4. Discussion ................................................................................................................ 106
4.4.1. Physicochemical characteristics of the Tema Harbour sediments ........................... 106
4.4.2. Effect of silt-clay and TOC content on the DDTs, HCHs and PAHs distribution .. 107
4.4.3. Sources of DDTs and HCHs in the Tema Harbour sediments ................................ 111
4.4.4. Sources of PAHs in the harbour sediments ............................................................. 112
4.4.5. Ecotoxicological risk characterisation ..................................................................... 115
Contents
xvii
4.5. Conclusion ............................................................................................................... 118
Chapter 5 ................................................................................................................................ 123
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana)
and its Ecological Implications .............................................................................................. 123
5.1. Introduction .............................................................................................................. 124
5.2. Materials and methods ............................................................................................. 126
5.2.1. Sediment sampling and sample analyses ................................................................. 126
5.2.2. Metal enrichment and contamination level .............................................................. 128
5.2.3. Data treatment .......................................................................................................... 129
5.3. Results...................................................................................................................... 129
5.3.1. Physicochemical characteristics of the Tema Harbour sediments ........................... 129
5.3.2. Metal concentrations and distribution patterns in sediments of Tema Harbour ...... 130
5.3.3. Metal fractionation, enrichment and pollution in Tema Harbour sediments ........... 133
5.4. Discussion ................................................................................................................ 136
5.4.1. Distribution and potential sources of metals in Tema Harbour surface sediments . 136
5.4.2. Metal fractionation in the Tema Harbour sediments ............................................... 139
5.4.3. Ecological implications of metal contamination in Tema Harbour sediments ........ 140
5.4.3.1. Ecotoxicological implications .......................................................................... 140
5.4.3.2. Ecological risk implications ............................................................................. 142
5.4.4. Chemical stability of Tema Harbour sediments ...................................................... 145
5.5. Conclusions.............................................................................................................. 146
Chapter 6 ................................................................................................................................ 151
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema
Harbour (Ghana) ..................................................................................................................... 151
6.1. Introduction .............................................................................................................. 152
6.2. Materials and methods ............................................................................................. 154
6.2.1. Study area ................................................................................................................ 154
6.2.2. Sediment sampling ................................................................................................... 156
6.2.3. Sampling of test organisms ...................................................................................... 156
6.2.4. Laboratory bioassay experiments ............................................................................ 157
6.2.5. Analyses of metal, sediment grain size and TOC contents ..................................... 158
6.2.6. Data analysis ............................................................................................................ 159
6.3. Results...................................................................................................................... 160
Contents
xviii
6.3.1. C. volutator and H. diversicolor mortalities in the whole-sediment bioassays ....... 160
6.3.2. Physicochemical conditions of water and sediments from the Tema Harbour and
control bioassays ..................................................................................................... 160
6.3.3. Total metal concentrations and metal fractionation in the analysed sediments ....... 162
6.3.4. Metal bioaccumulation in C. volutator and H. diversicolor .................................... 164
6.4. Discussion ................................................................................................................ 167
6.4.1. Hazard potential of Tema Harbour sediments ......................................................... 167
6.4.2. Potential ecological risks of metal contamination in Tema Harbour sediments ..... 169
6.4.3. Potential ecological impact of sediment-associated metal in Tema Harbour .......... 172
6.4.4. Dredged material management implications for Tema Harbour ............................. 173
6.5. Conclusion ............................................................................................................... 174
Chapter 7 ................................................................................................................................ 181
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps
and Sediment Cores in Tema Harbour (Ghana) ..................................................................... 181
7.1. Introduction .............................................................................................................. 182
7.2. Materials and methods ............................................................................................. 185
7.2.1. Study area ................................................................................................................ 185
7.2.2. Sediment sampling ................................................................................................... 187
7.2.3. Data treatment .......................................................................................................... 188
7.3. Results and discussion ............................................................................................. 190
7.3.1. Estimates of settling fluxes of particulate matter in the Tema Harbour .................. 190
7.3.2. Radionuclide and bulk density profiles in sediment cores from Tema Harbour ..... 193
7.3.3. Inventories and fluxes of 7Be and
7Be-derived sediment accumulation rates ......... 196
7.3.4. Analysis of 210
Pbexc fluxes onto the SWI and mixing .............................................. 199
7.3.5. Analyses of 210
Pb profiles and estimation of SARs using the TERESA model ...... 202
7.3.6. Analyses of sediment cores A, B and C .................................................................. 203
7.3.7. Analysis of sediment core D .................................................................................... 204
7.3.8. Comparison of SAR values among sediment cores A, B, C and D ......................... 206
7.3.9. Comparison of the TERESA- and 7Be-derived SARs ............................................. 207
7.4. Conclusions.............................................................................................................. 209
Chapter 8 ................................................................................................................................ 215
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema
Harbour (Ghana) ..................................................................................................................... 215
Contents
xix
8.1. Introduction .............................................................................................................. 216
8.2. Materials and methods ............................................................................................. 218
8.2.1. Study area ................................................................................................................ 218
8.2.2. Sediment sampling and analyses ............................................................................. 218
8.2.3. Quality control/assurance ........................................................................................ 219
8.2.4. Data analysis ............................................................................................................ 220
8.3. Results...................................................................................................................... 222
8.3.1. Metals, TOC and TN concentrations in settling silt-clay particles in the Tema
Harbour .................................................................................................................... 222
8.3.2. Distributions and fluxes of silt-clay particles associated metals in the Tema
Harbour .................................................................................................................... 225
8.4. Discussion ................................................................................................................ 231
8.4.1. Metal distribution and contamination in settling silt-clay partices in the Tema
Harbour .................................................................................................................... 231
8.4.2. Settling fluxes of silt-clay particles and associated metals in the Tema Harbour ... 235
8.4.3. Ecotoxicological risks of metal contamination in settling silt-clay particles in the
Tema Harbour .......................................................................................................... 236
8.5. Conclusions.............................................................................................................. 237
Chapter 9 ................................................................................................................................ 245
General discussion and conclusions ....................................................................................... 245
9.1. Sediment pollution and accumulation in habours .................................................... 246
9.1.1. Chemical pollution assessment of Tema Harbour sediments .................................. 247
9.1.1.1. Screening-level assessment of chemical pollution in the Tema Harbour
sediments ................................................................................................................. 247
9.1.1.2. Bioassay testing of Tema Harbour sediment .................................................... 249
9.1.2. Assessment of SARs in harbours ............................................................................. 252
9.1.2.1. Assessment of SARs in the Tema Harbour ...................................................... 253
9.1.2.1.1. Quantification of recent SARs in the Tema Harbour based on
7Be and
234Th
profiles and conventional 210
Pb dating models ........................................................ 254
9.1.2.1.2. Estimation of SARs from the 210
Pb-based TERESA model ............................. 255
9.1.2.2. Ecotoxicological implications of metal contamination in settling silt-clay
particles in the Tema Harbour ................................................................................. 255
9.2. General conclusions ................................................................................................. 256
Samenvatting .......................................................................................................................... 269
General Introduction
2
1.1. Background of this study
Coastal harbours are among marine environments highly vulnerable to chemical pollution as
they tend to receive and accumulate pollutants from maritime activities and other human
activities within their catchments, including urbanisation, industrialisation and agriculture
(Petrosillo et al., 2009; Smith et al., 2009; Lepland et al., 2010; Mestres et al., 2010; Schipper
et al., 2010; Nyarko et al., 2014; Romero et al., 2014). Coastal harbours are also prone to
siltation as a result of the influxes of sediment-laden seawater (Senten, 1989; Leys and
Mulligan, 2011) with subsequent deposition and accumulation of the sediments within the
harbour basin under favourable hydrodynamic conditions (Smith et al., 2009; Lepland et al.,
2010; Luo et al., 2010; Mestres et al., 2010; Schipper et al., 2010). Chemical pollution and
high sediment accumulation rates (SARs) in harbours are major environmental issues as they
pose a threat to harbour sustainability and result in adverse human health, ecological and
socio-economic impacts (Syvitski et al., 2005; Van Rijn 2005; Casado-Martinez et al., 2006;
Birch and Hutson, 2009; Lepland et al., 2010; Mestres et al., 2010; Schipper et al., 2010;
Green and Coco, 2014).
The management of sediment pollution and accumulation in harbours commonly involves
dredging (Burton, 2002) with subsequent disposal in other aquatic or terrestrial ecosystems
(Caille et al., 2003; Witt et al., 2004; Bolam et al., 2006; Schipper et al., 2010). Dredging has
both economic and ecological implications as it is usually costly (Qu and Kelderman, 2001;
Barneveld and Hugtenburg, 2008; Schipper et al., 2010) and moreover, the pollutants in the
disposed materials are capable of exerting detrimental effects on the receiving ecosystems
(Hong et al., 1995; Burton, 2002; Caille et al., 2003; Stronkhorst and van Hattum, 2003;
Casado-Martinez et al., 2006; Birch and Hutson, 2009; Choueri et al 2009; Schipper et al.,
2010). Thus, dredged material disposal is now recognized as a major environmental issue.
Sediment pollutants of notable concern include metals and persistent organic pollutants
(POPs), exemplified by polycyclic aromatic hydrocarbons (PAHs) and organochlorine
pesticides (OCPs), due to their toxicity, environmental persistence and potential for
bioaccumulation and transfer along food chains (Chau, 2005; Casado-Martinez et al., 2006;
Schipper et al., 2010; Nyarko et al., 2011; Kelderman, 2012; Iqbal et al., 2013; Romano et al.,
2013). Thus, information on sediment contamination and accumulation rates in harbours is
relevant for their management, e.g., for predicting the time to dredge.
General Introduction
3
The coastal Tema Harbour in Ghana (Fig. 1.1) was constructed in 1960 and has been in
operation since 1962 when it was commissioned. Industrialisation of the harbour area also
started in the early 1960s and has seen much growth over the years.
Fig. 1.1 Aerial view of the Tema Harbour (Google Earth)
Major industrial activities in the harbour zone include oil refining, ore smelting, and
manufacture of paints and cement. The harbour has fourteen berths including a dedicated oil
berth, where oil is discharged by oil tankers, and a shipyard with two dry docks for servicing
of ships. A wide range of ships call at the harbour including oil tankers, general cargo,
container ships and bulk carriers, which transport e.g. fertilizer, ores, petroleum products and
chemicals. Container traffic at the harbour increased by about 400%, i.e., from 150,000
Twenty-Foot Equivalent Units (TEUs) to 750,000 TEUs between the year 2000 and 2011
(http://ghanaports.gov.gh/GPHA). During this period, there were two major oil spills in the
General Introduction
4
Tema Harbour and a fire outbreak at the Tema shipyard, which destroyed oil pipeline
installations at the harbour. Maintenance dredging is conducted in the harbour periodically
with subsequent disposal in the adjacent sea. In order to increase the handling capacity of the
Tema Harbour to about 1,000,000 TEUs, the Ghana Ports and Harbours Authority (GPHA)
proposed to undertake expansion works at the Tema Harbour. It is expected that this project,
when completed, will boost industrial activities and thus, the Tema Harbour may be highly
impacted through important loads of pollutants and sediments. In order to understand and
minimise the anthropogenic impacts, a comprehensive assessment of chemical pollution and
sedimentation in the Tema Harbour is crucial.
Prior to this thesis, no comprehensive assessment of chemical pollution and sedimentation
was conducted in the Tema Harbour. Baseline studies in the Tema Harbour have focused on
total metal (http://open_jicareport.jica.go.jp/pdf/11681632_03.pdf; Nyarko et al., 2014) and
total PAH (Gorleku et al., 2014) contamination in surface sediments. However, harbour
sediments are often contaminated by a wide range of chemical pollutants (Casado-Martinez et
al., 2006; Long et al., 2006; Birch and Hutson, 2009; Schipper et al., 2010). The aim of this
thesis was, therefore, to investigate chemical pollution and sedimentation conditions in the
Tema Harbour. The thesis objectives were to:
(1) Assess chemical contamination in sediments from the Tema Harbour and its
ecotoxicological implication
(2) Evaluate the biological effects of chemical contamination in the Tema Harbour sediments
(3) Quantify settling fluxes of sediments and associated contaminants as well as recent
sediment accumulation rates in the Tema Harbour.
1.2. Research approach
With an integral view of the research problem, a rigorous multidisciplinary and integrated
approach was adopted to assess the chemical pollution and sedimentation in the Tema Harbour
as shown in Fig. 1.2. To assess chemical pollution in the Tema Harbour sediments, chemical
analysis and a screening-level risk assessment were first conducted on the Tema Harbour
sediments to identify contaminants of potential concern by using Sediment Quality Guidelines
(SQGs) and the Environmental Risk from Ionising Contaminants Assessment and
Management (ERICA) tool. This screening-level risk assessment was reinforced by whole-
General Introduction
5
sediment bioassays to evaluate the hazard potential of the Tema Harbour sediments and to
assess the potential ecological impact of metal contamination in the harbour sediments.
To assess sedimentation conditions in the Tema Harbour, sediment core analysis was combined
with the analysis of particulate matter accumulated in sediment traps at different periods. This
allowed for an understanding of Suspended Particulate Matter (SPM) dynamics and the
processes affecting the distribution and dynamics of sediment-associated contaminants in the
Tema Harbour. The robust quantitative 210
Pb-based TERESA (Time Estimates from Random
Entries of Sediments and Activities) model was combined with the measurement of short-lived
radioisotopes (234
Th and 7Be) in sediment cores to depict a reliable scenario for sedimentation
in the Tema Harbour. This allowed for the quantification of recent SARs in the disturbed Tema
Harbour where (1) conventional 210
Pb-based dating methods fail, (2) the use of sediment traps
and 234
Th and 7Be profiles in sediment cores show serious constraints, and (3) SARs fall
beyond the capabilities of GIS-bathymetry.
1.3. Structure of this thesis
Before pursuing the thesis objectives, a review of pertinent literature was conducted and is
presented in Chapter 2. The objectives of this thesis were pursued in Chapters 3-8. Chapters 3-5
dealt with objective 1: Chapter 3 focused on radionuclide contamination, Chapter 4 on organic
pollutant (PAH, DDT and HCH) contamination, while Chapter 5 assessed the potential mobility
of sediment-bound metals in surface sediments of the Tema Harbour and the ecological risk
implications. The screening-level risk assessment was reinforced by whole-sediment bioassays
to evaluate the hazard/toxic potential of the harbour sediments and assess the potential
ecological impact of metal contamination in the sediments, and is presented in Chapter 6.
Objective 3 is dealt with under chapters 7 and 8. Chapter 7 investigated SPM dynamics and
recent sediment accumulation rates in the Tema Harbour, while Chapter 8 investigated settling
fluxes of fine sedimentary metals and their ecotoxicological implications in the Tema
Harbour. A synthesis of Chapters 3-8 is then presented in Chapter 9.
General Introduction
6
Fig. 1.2 Schematic presentation of the thesis approach to investigate chemical
pollution of sediments and sedimentation rates in the Tema Harbour
References
Barneveld, H., & Hugtenburg, J. (2008). Feasibility study for implementation of
sedimentation reduction measures in river harbours. RCEM, 1187-1192.
Birch, G.F., & Hutson, P. (2009). Use of sediment risk and ecological/conservation value for
strategic management of estuarine environments: Sydney estuary, Australia. Environ.
Manage. 44, 836-850.
Bolam, S.G., Rees, H.L., Somerfi eld, P., Smith, R., Clarke, K.R., Warwick, R.M., Atkins, M.,
& Garnacho, E. (2006). Ecological consequences of dredged material disposal in the
marine environment: a holistic assessment of activities around the England and Wales
coastline. Mar. Pollut. Bull. 52(4), 415-26.
Sediment accumulation/
accretion rates
Site survey and harbour
information gathering
Sediment grab
sampling
Sediment trap sampling and
turbidity measurements
Sediment core
sampling
Contaminant/physico-chemical
analyses, bioassays and metal
bioaccumulation
Particulates and
metal analyses
Settling fluxes and
SPM dynamics
Bulk density profiling
and radiometric dating
Ecological hazard, risk
and impact evaluation
Chemical pollution of sediments and sedimentation rates in the Tema Harbour
General Introduction
7
Burton, G.A. Jr. (2002). Sediment quality criteria in use around the world. Limnology, 3(2),
65-76.
Caille, N., Tiffreau, C., Leyval, C. & Morel, J.L. (2003). Solubility of metals in an anoxic
sediment during prolonged aeration. Sci. Total Environ. 301(1), 239-250.
Casado-Martínez, M.C., Buceta, J.L., Belzunce, M.J., & DelValls, T.A. (2006). Using
sediment quality guidelines for dredged material management in commercial ports
from Spain. Environ. Int. 32, 388-396.
Chau, K. W. (2005). Characterization of transboundary POP contamination in aquatic
ecosystems of Pearl River delta. Mar. Pollut. Bull. 51(8–12), 960-965.
Choueri, R. B., Cesar, A., Abessa, D.M.S., Torres, R.J., Morais, R.D., Riba, I., Pereira,
C.D.S., Nascimento, M.R.L., Mozeto, A.A., & DelValls, T.A. (2009). Development of
site-specific sediment quality guidelines for North and South Atlantic littoral zones:
Comparison against national and international sediment quality benchmarks. J.
Hazard. Mater. 170, 320-331.
Gorleku, M.A., Carboo, D., Palm, L.M.N., Quasie, W.J. & Armah, A.K. (2014). Polycyclic
aromatic hydrocarbons (PAHs) pollution in marine waters and sediments at the Tema
Harbour, Ghana. Acad. J. Environ. Sci. 2(7), 108-115.
Green, M.O., & Coco, G. (2014). Review of wave‐driven sediment resuspension and transport
in estuaries. Rev. Geophys, 52(1):77-117.
Hong, H., Xu, L.-J., Zhang, L., Chen, J., Wong, Y. & Wan, T. (1995). Special guest paper:
environmental fate and chemistry of organic pollutants in the sediment of Xiamen and
Victoria Harbours. Mar. Pollut. Bull. 31(4), 229-236.
Iqbal, J., Tirmizi, S., & Shah, M. (2013). Statistical apportionment and risk assessment of
selected metals in sediments from Rawal Lake (Pakistan). Environ. Monit. Assess.
185(1), 729-743.
Kelderman, P. (2012). Sediment Pollution, Transport, and Abatement Measures in the City
Canals of Delft, the Netherlands. Water Air Soil Pollut. 223(7), 4627-4645.
Lepland, A., Andersen, T.J., Lepland, A., Arp, H.P.H., Alve, E., Breedveld, G.D., & Rindby,
A. (2010). Sedimentation and chronology of heavy metal pollution in Oslo harbor,
Norway. Mar. Pollut. Bull. 60(9), 1512-1522.
Leys, V., & Mulligan, R.P. (2011). Modelling coastal sediment transport for harbour
planning: selected case studies. INTECH.
General Introduction
8
Long, E.R., Ingersoll, C.G. & MacDonald, D.D. (2006). Calculation and uses of mean
sediment quality guideline quotients: a critical review. Environ. Sci. Technol. 40(6),
1726-1736.
Luo, W., Lu, Y., Wang, T., Hu, W., Jiao, W., Naile, J.E., Khim, J.S., & Giesy, J.P. (2010).
Ecological risk assessment of arsenic and metals in sediments of coastal areas of
northern Bohai and Yellow Seas, China. Ambio, 39(5-6), 367-375.
Mestres, M., Sierra, J., Mösso, C., & Sánchez-Arcilla, A. (2010). Sources of contamination
and modelled pollutant trajectories in a Mediterranean harbour (Tarragona, Spain).
Mar. Pollut. Bull. 60(6), 898-907.
Nyarko, E., Botwe, B.O., Lamptey, E., Nuotuo, O., Foli, B.A., & Addo, M.A. (2011). Toxic
metal concentrations in deep-sea sediments from the jubilee oil field and surrounding
areas off the western coast of Ghana. Tropical Environ. Res. 9, 584-595.
Nyarko, E., Fletcher, A., Addo, S., Foli, B.A.K., & Mahu, E. (2014). Geochemical assessment
of heavy metals in surface sediments: A case study of the Tema Port, Ghana. J.
Shipping Ocean Engin. 4, 79-92.
Petrosillo, I., Valente, D., Zaccarelli, N., & Zurlini, G. (2009). Managing tourist harbors: Are
managers aware of the real environmental risks? Mar. Pollut. Bull. 58, 1454-1461.
Qu, W., & Kelderman, P. (2001). Heavy metal contents in the Delft canal sediments and
suspended solids of the River Rhine: multivariate analysis for source tracing.
Chemosphere, 45(6), 919-925.
Romano, S., Piazza, R., Mugnai, C., Giuliani, S., Bellucci, L. G., Nguyen Huu, C., . . .
Frignani, M. (2013). PBDEs and PCBs in sediments of the Thi Nai Lagoon (Central
Vietnam) and soils from its mainland. Chemosphere, 90(9), 2396-2402.
Romero, A.F., Asmus, M.L., Milanelli, J.C.C., Buruaema, L., & Abessa, D.M.S. (2014). Self-
diagnosis method as an assessment tool for environmental management of Brazilian
ports. Journal of Integr. Coastal Zone Manage. 14(4), 637-644.
Schipper, C., Rietjens, I., Burgess, R., Murk, A. (2010). Application of bioassays in
toxicological hazard, risk and impact assessments of dredged sediments. Mar. Pollut.
Bull. 60(11), 2026-2042.
Senten, J.R. (1989) Pollution of harbour sediments by heavy metals. Ocean & Shoreline
Manage. 12, 463-475.
Smith, J., Lee, K., Gobeil, C. & Macdonald, R. (2009). Natural rates of sediment containment
of PAH, PCB and metal inventories in Sydney Harbour, Nova Scotia. Sci. Total
Environ. 407(17), 4858-4869.
General Introduction
9
Stronkhorst, J., & Van Hattum, B. (2003). Contamination of concern in Dutch marine harbour
sediments. Arch. Environ. Contam. Toxicol. 45, 306-316.
Syvitski, J.P, Vörösmarty, C.J, Kettner, A.J., Green, P. (2005). Impact of humans on the flux
of terrestrial sediment to the global coastal ocean. Science, 308(5720), 376-380.
Van Rijn, L.C. (2005). Estuarine and coastal sedimentation problems. Int. J. Sediment Res.
20(1):39-51.
Witt, J., Schroeder, A., Knust, R., & Arntz, W.E. (2004). The impact of harbour sludge
disposal on benthic macrofauna communities in the Weser estuary. Helgol. Mar. Res.
58, 117-128.
Literature Review
12
2.1. Chemical pollution in coastal marine environments
The United Nations (UN) Group of Experts on the Scientific Aspects of Marine
Environmental Protection (GESAMP) defined marine pollution as: "The introduction by man,
directly or indirectly, of substances or energy into the marine environment (including
estuaries) resulting in such deleterious effects as harm to living resources, hazards to human
health, hindrance to marine activities, including fishing, impairment of quality for use of sea
water and reduction of amenities." Thus, chemical pollution in coastal marine environments
pertains to the anthropogenic release of chemical substances into coastal marine
environments, which results in adverse human health, ecological and socio-economic effects.
Chemical pollution in coastal marine environments is closely linked to ocean- and land-based
human activities (Williams, 1996; Islam and Tanaka, 2004; Petrosillo et al., 2009). Land-
based activities include industrial and agricultural production, urban and coastal
infrastructural development, tourism and mining (Simpson et al., 1996; Clark, 2001; Simboura
and Zenetos, 2002; Islam and Tanaka, 2004; Petrosillo et al., 2009; Smith et al., 2009; Mestres
et al., 2010; Lepland et al., 2010). Chemical pollutants from land-based activities enter coastal
marine environments by various means, including river and groundwater influx, surface run-
offs, atmospheric transport and deposition, direct discharges of industrial effluents and
municipal outfall (Clark, 2001; Islam and Tanaka, 2004; Ruiz-Fernandez et al., 2009). Ocean-
based activities such as offshore crude oil extraction, fishing, mariculture, maritime transport
and dumping result in direct discharge of pollutants into the marine environment (Simpson et
al., 1996; Williams, 1996; Simboura and Zenetos, 2002; Islam and Tanaka, 2004; Petrosillo et
al., 2009; Simth et al., 2009; Mestres et al., 2010; Lepland et al., 2010).
With over 50% of the world‘s population inhabiting coastal areas (Gupta et al., 2005;
Petrosillo et al., 2009), land-based activities are by far the major contributor (nearly 80%) to
chemical pollution in the marine environment, with ocean-based activities (mainly maritime
transport and dumping at sea) contributing about 20% (Williams, 1996). Estuaries (Meybeck
and Vörösmarty, 2005; Birch et al., 2015; Alvarez-Vazquez et al., 2017) and coastal harbours
(Simpson et al., 1996; Birch and Hutson, 2009; Lin et al., 2009; Smith et al., 2009; Lepland et
al., 2010; Mestres et al., 2010; Schipper et al., 2010) are particularly vulnerable to chemical
pollution as they are often associated with intense human activities.
Literature Review
13
Although environmental pollution can be traced back to the beginning of the history of human
civilization (Islam and Tanaka, 2004; Magi and Di Carro, 2016), chemical pollution of the
marine environment began to receive global attention during the mid-20th
century (Magi and
Di Carro, 2016), mainly as a result of global industrialisation, which resulted in an
unprecedented release of chemical substances into the environment (Gaillardet et al., 2003;
Wang et al., 2010). It is now known that many coastal marine environments are polluted
(Islam and Tanaka, 2004; Wang et al., 2014; Vikas and Dwarakish, 2015).
2.2. Types and effects of chemical pollutants in coastal marine environments
A variety of chemical pollutants including metals, organic chemicals and radionuclides is
often present in coastal marine environments from varied sources (Casado-Martinez et al.,
2006; Long et al., 2006; Birch and Hutson, 2009; Schipper et al., 2010). In terms of human
health and ecological significance, however, priority pollutants include (1) metals/metalloids
such as Cd, Hg, Ni, Pb, Cr, Cu, Zn, Sn and As, (2) radionuclides such as 210
Po, 210
Pb, 226
Ra,
238U,
232Th,
228Ra,
228Th,
40K and
137Cs, and (3) persistent organic pollutants (POPs) such as
polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), organochlorine
pesticides (OCPs), and biocides such as the organotin compound tributyltin (TBT) (Williams,
1996; Volesky, 2001; Islam and Tanaka, 2004; Casado-Martinez et al., 2006; Birch and
Hutson, 2009; Schipper et al., 2010; Magi and Di Carro, 2016).
TBT is notorious for imposex, a condition where females of certain species of whelk and
gastropod develop male organs (Clark, 2001; Schipper et al., 2008), resulting in a decline in
whelk and gastropod population (Ten Hallers-Tjabbes et al., 1994; Champ and Seligman,
1996; Mensink et al., 1996a, b; Schipper et al., 2008). These chemical pollutants are persistent
and bioaccumulative with the potential to be transferred along the food chain (Chau, 2005;
Nyarko et al., 2011a; Kelderman, 2012; Iqbal et al., 2013; Romano et al., 2013). They are also
toxic and may exert a broad range of effects, including cancer, mutation, hormonal disruption,
reproductive anomalies, death of organisms and loss of biodiversity, alteration/destruction of
ecological habitats, declines in productivity, restrictions on seafood consumption, human
diseases, hindrance to coastal activities, poverty, and costly remediation (Williams, 1996;
Islam and Tanaka, 2004; Stoschek and Zimmermann, 2006; Lepland et al., 2010).
Literature Review
14
In recent decades, a wide range of organic compounds referred to as chemicals of emerging
concern (COEC) have been recognized as potentially hazardous to human and aquatic life
(Stronkhorst and van Hattum, 2003; Schipper et al., 2010; Geissen et al., 2015; Magi and Di
Carro, 2016). Some COEC are halogenated organic compounds and are thus potentially
persistent and bioaccumulative. They include brominated flame retardants (BFRs) such as
polybrominated diphenyl ethers (PBDEs); perfluorinated chemicals (PFCs) such as
perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA); polychlorinated
dibenzodioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and polychlorinated
naphthalenes (PCNs). Most of the halogenated COEC have been designated as priority
pollutants by the European Union.
2.3. Sources of chemical pollutants in coastal marine environments
Sediment-associated pollutants in coastal marine environments may emanate from different
sources. Metals may be present in sediments as a result of their natural occurrence in rocks
and the Earth‘s crust (Clark, 2001). Anthropogenic inputs originate from e.g. combustion of
fossil fuels, mining and smelting operations, industrial and manufacturing processes, and
waste disposal (Zhou et al., 2008; Iqbal et al., 2013; Alvarez-Vazquez et al., 2017). They have
exceeded natural or background levels in many areas (Rae, 1997; Clark, 2001; Chatterjee et
al., 2007; Iqbal et al., 2013; Wang et al., 2014). Radionuclides may also be present in
sediments as a result of their natural occurrence in rocks, the Earth‘s crust and the atmosphere
as well as from anthropogenic sources. Major anthropogenic sources include the global
nuclear tests conducted between the mid-1940s and the 1980s, nuclear accidents, nuclear fuel
reprocessing and discharges from nuclear industries (Clifton et al., 1995; Livingston and
Povinec, 2000). Anthropogenic activities such as agriculture, mining, and oil and gas
development may also lead to enhancement in the environmental levels of radionuclides
referred to as Technologically Enhanced Naturally-Occurring Radioactive Materials
(TENORM) (UNSCEAR, 2000; Al-Trabulsy et al., 2011; Nyarko et al., 2011b).
Like metals and radionuclides, the sources of PAHs in the marine environment may be natural
(e.g. natural forest fires and diagenetic processes) or anthropogenic such as waste incineration,
coal processing, crude oil refining, combustion of fossil fuels and spillage of crude oil (Mai et
al., 2003; Yim et al., 2007; Giuliani et al., 2008). Unlike metals, PAHs and radionuclides,
OCPs have no known natural origin; they are synthetic and have been released into the
Literature Review
15
environment through their use for pest control in agriculture and public health programmes
(Rajendran et al., 2005; Ntow and Botwe, 2011; Thomas et al., 2012; Ahmed et al., 2015).
The source of TBT in the marine environment is the use of TBT-based paints for coating of
marine crafts and docks in harbours to control biofouling (Williams, 1996; Berto et al., 2007;
Schipper et al., 2008; Nyarko et al., 2011a; Castro et al., 2012). Thus, commercial ports,
dockyards and marinas are potential ‗hot-spots‘ of TBT pollution. COEC have diverse sources
such as pharmaceuticals, disinfection by-products, pesticides, industrial chemicals and wood
preservatives (Sauvé and Desrosiers, 2014; Geissen et al., 2015).
2.4. Fate of chemical pollutants in coastal marine environments
Most chemical pollutants including radionuclides (Pfitzner et al., 2004; Yeager et al., 2005;
Santschi et al., 2006; Mabit et al., 2008), metals (Santschi et al., 2001; Kelderman and Osman,
2007; Ruiz-Fernandez et al 2009; Lepland et al., 2010), OCPs and PAHs (Wang et al., 2001;
Luo et al., 2004; Yang et al., 2005; Hu et al., 2009; Lin et al., 2009) that enter coastal marine
environments are extremely particle-reactive. This usually results in a larger component of the
pollutants partitioning to particulates (Gómez-Gutiérrez et al., 2007; Santschi et al., 2001),
particularly the fine silt and clay particles, compared to the overlying water (Power and
Chapman, 1992; Nyarko et al., 2011a). Thus, sediments participate in the fate of chemical
pollutants in aquatic systems (Mulligan et al., 2001; Ruiz-Fernandez et al 2009; Prato et al.,
2011; Jiang et al., 2013), acting as an important source of exposure of chemical pollutants to
benthic organisms via direct contact or ingestion (Bat and Raffaelli, 1998; Mulligan et al.,
2001; Burton, 2002; DelValls et al., 2004; Burgess et al., 2007; Gómez-Gutiérrez et al., 2007;
Birch and Hutson, 2009). Metals (Rainbow, 2007; Schipper et al., 2010; Carvalho et al.,
2012; Gaion et al., 2014), POPs (Burton, 2002; Islam and Tanaka, 2004; Birch and Hutson,
2009) and radionuclides (Hassona et al., 2008; Sirelkhatim et al., 2008) can subsequently
accumulate in the tissues of benthic invertebrates and other organisms in the marine food web.
Metals are non-degradable; radionuclides degrade through radioactive decay, whereas organic
pollutants slowly degrade via weathering and biochemical conversion to other compounds
(James, 2002; Rani et al., 2017). For example, the radioactive decay of 226
Ra and the
degradation of DDT are shown in Figs. 2.1 and 2.2, respectively.
Literature Review
16
226Ra α
222Rn several T1/2
210Pb β
210Bi β
210Po
T1/2 1600 y 3.82 d 22.3 y 5.01 d 138.4 d
Fig. 2.1 Radioactive decay of 226Ra to 210Po through several intermediate
radionuclides
Fig. 2.2 Degradation of DDT to DDE, DDD and other metabolites (Quensen III et al.,
1998).
The fate of metals (Kelderman and Osman, 2007; Di Palma and Mecozzi, 2007; Hamzeh et
al., 2014), radionuclides (Sirelkhatim et al., 2008; Sugandhi et al., 2014) and organic
pollutants (Lin et al., 2009) is influenced by environmental factors such as the pH and redox
state. Other factors include microbiological processes (Ryding, 1985) and the presence of
Fe/Mn oxides and hydroxides or organic matter (Horowitz and Elrick, 1987; Wang et al.,
2001; Islam and Tanaka, 2004; Dung et al., 2013; Hamzeh et al., 2014). Sediment organic
matter (OM) may derive from marine phytoplankton (autochthonous sources) or terrestrial
higher plants (allochthonous sources), which may be distinguished by their total organic
carbon (TOC)/total nitrogen (TN) ratios. Generally, OM of autochthonous sources is
characterised by a TOC/TN ratio ≤ 6-8:1, while that of allochthonous sources is characterised
Literature Review
17
by a TOC/TN ratio ≥ 20:1 (Burdige, 2007; Tesi et al., 2007; Guerra et al., 2010; Mahapatra et
al., 2011). Thus, the TOC/TN ratios allow an assessment of the predominant source of OM in
marine sediments.
2.5. Assessment of chemical pollution in coastal marine environments
In addition to their high affinity for chemical pollutants, sediments show lower variation in
pollutant concentrations than their overlying water (Beiras et al., 2003). Therefore, sediments
are considered as a better indicator of chemical pollution than the water phase (Sundberg et
al., 2005; Denton et al., 2006; Giuliani et al., 2011; Moukhchan et al., 2013) and have become
a major tool for the assessment of chemical pollution in aquatic environments (Díaz-de Alba
et al., 2011; Kalwa et al., 2013).
In the GESAMP context of marine pollution, the assessment of chemical pollution in
sediments should involve the 4 steps as shown in Fig. 2.3. These steps are described in detail
in the text below.
Fig. 2.3 Schematic presentation of the assessment of chemical pollution in sediments
2.5.1. Inventory of chemical pollutants in sediments
Accurate measurement of chemical pollutants is necessary in pollution assessment since it can
provide information on the potentially toxic chemicals in the sediments and help identify
appropriate remediation techniques. Considering that a variety of chemical pollutants may be
present in marine sediments (Casado-Martinez et al., 2006; Long et al., 2006; Birch and
Inventory of chemical pollutants in sediment
Human health and ecotoxicological risk
characterisation
Pollutant source apportionment
Hazard and impact assessment
Literature Review
18
Hutson, 2009; Schipper et al., 2010), it is impractical to analyse the whole range of chemical
pollutants in sediments. Moreover, the analysis of COEC in sediments is currently a challenge
since they are typically present in very low concentrations and the development of sampling
protocols and analytical techniques is at its infancy (Geissen et al., 2015). On the contrary,
sampling protocols, standard analytical techniques and standard reference materials (SRMs)
or certified reference materials (CRMs) that allow accurate measurements are well-developed
for most of the classical chemical pollutants including radionuclides, OCPs, PAHs and metals.
These pollutants are of wide interest due to their potential toxicity and adverse biological
effects such as cancer, mutations and reproductive anomalies (Willett et al., 1998; Wang et al.,
2001; Little, 2003; Islam and Tanaka, 2004; King et al., 2004; De Luca et al., 2004; Casado-
Martinez et al., 2006; Schmid and Schrader, 2007; Hassona et al., 2008; Sirelkhatim et al.,
2008; Birch and Hutson, 2009; Schipper et al., 2010; Ravanat et al., 2014).
Radionuclides of interest include 238
U, 210
Pb, 226
Ra, 232
Th, 228
Ra, 228
Th, 40
K and 137
Cs
(Hassona et al., 2008; Sirelkhatim et al., 2008; Ulanovsky et al., 2008), while banned OCPs of
greatest interest include DDT (dichlorodiphenyltrichloroethane) and HCH
(hexachlorocyclohexane) (Walker et al. 1999; Yang et al., 2005; Hu et al., 2009; Lin et al.,
2009; Singh and Lal 2009). DDT and HCH (see Fig. 2.4) are targeted for global elimination
and consequently banned in many countries under the Stockholm Convention on persistent
organic pollutants (Ntow and Botwe, 2011), which seeks to protect human health and the
environment from the harmful effects of these pollutants. However, concerns about these
banned OCPs remain due to their environmental persistence, weak enforcement of their ban,
the disposal of stockpiles and the permitted use of DDT in some malaria endemic developing
countries (Ntow and Botwe, 2011; Ahmed et al., 2015).
(a) DDT (b) HCH
Fig. 2.4 Chemical structures of (a) DDT and (b) HCH
Literature Review
19
Metals of greatest concern include Pb, Cu, Zn, As, Cr, Ni, Cd, Sn and Hg (Volesky, 2001;
Casado-Martinez et al., 2006; Schipper et al., 2010). PAHs are a mixture of several congeners,
which may be classified as low molecular weight PAHs (containing two or three fused
benzene rings) and high molecular weight PAHs (containing four to six fused benzene rings)
(Yunker et al., 2000; Yunker et al., 2002; Neff et al., 2005). 16 PAHs (see Fig. 2.5) have been
designated as priority pollutants by the United States Environmental Protection Agency
(USEPA) and are, therefore, the main target in terms of environmental monitoring of PAHs
(Nisbet and LaGoy, 1992; Wang et al 2001; De Luca et al., 2004; King et al., 2004).
2.5.2. Pollutant source apportionment in sediments
For sediment-associated chemical pollutants that may emanate from natural and
anthropogenic sources, it is the anthropogenic component that is related to pollution
(Chapman, 2007). Thus, Chapman and Anderson (2005) provide a distinction between
―pollution‖ and ―contamination‖, the former occurring when the presence of a pollutant in the
environment results in harmful biological effects, while the latter refers to the presence of a
pollutant that is either not normally found in the environment or above the natural background
concentration. Delineating the anthropogenic sources from the natural sources is, therefore, of
interest in chemical pollution assessment (Aloupi and Angelidis, 2001; Chapman, 2007;
Chatterjee et al., 2007; Dung et al., 2013). Radionuclides of natural (e.g. 238
U, 210
Pb, 226
Ra,
232Th,
228Ra,
228Th,
40K and
7Be) and artificial (e.g.
90Sr,
137Cs,
239Pu,
240Pu and
241Am) sources
are well known. However, natural radionuclide enrichment in sediments may occur as a result
of anthropogenic activities (UNSCEAR, 2000; Al-Trabulsy et al., 2011; Nyarko et al., 2011b)
and this can be assessed by comparing measured concentrations in sediments with background
concentrations.
2.5.2.1. DDT and HCH
DDT is of anthropogenic origin (Ntow and Botwe, 2011) and it undergoes degradation mainly
to dichlorodiphenyldichloroethylene (DDE) and dichlorodiphenyldichlororethane (DDD) (see
Fig. 2.2), which are all persistent with similar physical and chemical characteristics (WHO,
1989). DDT was commercially produced as technical DDT with a characteristic composition,
which can provide insight into the timing of their use. This is relevant for assessing the
effectiveness of the ban/regulation of the pesticides (Botwe et al., 2012). Technical DDT has a
Naphthalene
Anthracene
Phenanthrene
Fluorene
Acenaphthene
Acenaphthylene
Pyrene
Fluoranthene
Benz[a]anthracene
Chrysene
Dibenz[a,h]anthracene
Benzo[b]fluoranthene
Benzo[k]fluoranthene
Benzo[a]pyrene
Indeno[1,2,3-cd]pyrene
Benzo[ghi]perylene
Fig. 2.5 Chemical structures of the USEPA 16 priority PAHs
Literature Review
21
composition of 77% p,p'-DDT, 4.0% p,p'-DDE and 0.3% p,p'-DDD. Due to the low
proportions of DDE and DDD in technical DDT, the DDT/DDD and DDT/(DDE + DDD)
ratios < 1.0 are generally indicative of past use of DDT, whereas ratios > 1.0 point to current
use (Lin et al., 2009; Botwe et al., 2012). HCH may be present in the environment as isomers
namely -HCH, -HCH, -HCH and -HCH (Fig. 2.6), which are all persistent with similar
physical and chemical characteristics (Willett et al., 1998; Walker et al., 1999; Singh and Lal,
2009) and can undergo interconversions (Walker et al., 1999; Yang et al., 2005; Hu et al.,
2009).
Fig. 2.6 Chemical structures of -HCH, -HCH, -HCH and -HCH isomers
(Srivastava and Shivanandappa, 2010)
HCH was commercially produced as technical HCH and lindane. The major composition of
technical HCH are α-HCH (60-70%) > γ-HCH (10-15%) > β-HCH (5-12%) > δ-HCH (6-10
%) (Willett et al. 1998; Walker et al., 1999; Singh and Lal, 2009). Interestingly, the
insecticidal potency of technical HCH is mainly associated with -HCH despite the higher
proportion of the α-HCH isomer (Willett et al., 1998; Walker et al., 1999; Singh and Lal,
2009). This knowledge provided an impetus for further refinement of technical HCH to the
commercial production of high-purity γ-HCH referred to as lindane, which contains over 99%
of the γ-HCH isomer with only trace amounts of the other isomers (Walker et al., 1999; Singh
and Lal, 2009). The distinct HCH isomeric compositions of technical HCH and lindane
provide a basis for delineation of these two HCH sources: technical HCH has α-HCH/γ-HCH
ratios ranging between 3 and 7 whereas those of lindane are close to 1.0 or < 1.0 (Willett et
al., 1998).
Literature Review
22
2.5.2.2. PAHs
PAH sources related to oil spills are described as petrogenic, while sources related to the
incomplete combustion of organic matter and fossil fuel are described as pyrogenic (Wang et
al., 2001; Yunker et al., 2002; Yan et al., 2006; Yim et al., 2007; Abrajano et al., 2007).
Petrogenic sources are enriched in low molecular weight PAHs (LPAHs) but depleted in high
molecular weight PAHs (HPAHs), whereas the converse holds for pyrogenic sources (Yunker
et al., 2000; Yunker et al., 2002; Neff et al., 2005). The difference in the compositions of
PAHs originating from petrogenic and pyrogenic sources provides a basis for the
characterisation of these PAH sources in sediments: a ΣLPAH/ΣHPAH ratio > 1.0 indicates
petrogenic sources, while a ratio < 1.0 indicates pyrogenic sources (Rocher et al., 2004).
Various PAH isomeric ratios such as Anthracene/(Anthracene + Phenanthrene),
Fluoranthene/(Fluoranthene + Pyrene) and Benzo[a]Anthracene/(Benzo[a]Anthracene +
Chrysene) (Yunker et al., 2002; Abrajano et al., 2003; Rocher et al., 2004; Nyarko et al.,
2011c; Guerra, 2012) have also been used as diagnostic tools for PAH source apportionment.
An Anthracene/(Anthracene + Phenanthrene) ratio < 0.10 points to a petrogenic source, while
a ratio > 0.10 signifies a pyrogenic source. A Fluoranthene/(Fluoranthene + Pyrene) ratio <
0.50 is indicative of a petrogenic source, while a ratio > 0.50 indicates a pyrogenic source. A
Benzo[a]Anthracene/(Benzo[a]Anthracene + Chrysene) ratio < 0.20 characterises a petrogenic
source, a ratio of 0.20-0.35 indicates mixed petrogenic and pyrogenic sources, while a ratio >
0.35 points to a pyrogenic source (Yunker et al., 2000; Yunker et al., 2002).
2.5.2.3. Metals
Quantitative geochemical approaches such as the metal enrichment factor (EF) proposed by
Sinex and Helz (1981) and the geo-accumulation index (Igeo) proposed by Muller (1969) are
widely used to apportion the sources of metals in sediments. These geochemical indices
compare measured concentrations of metals in sediment samples with their corresponding
concentrations in pre-impacted samples to (1) evaluate metal enrichment and contamination
status and (2) identify the predominant source of metals in sediments as natural or
anthropogenic. Where metal concentrations in pre-impacted sediment samples are not
available, metal enrichment and contamination are assessed by using metal concentrations in
deep layers of sediment cores (Birch and Olmos, 2008; Abrahim and Parker, 2008; Yilgor et
al., 2012), average crustal metal concentrations (Sinex and Helz, 1981; Addo et al., 2012;
Literature Review
23
Mahu et al., 2015) or average shale metal concentrations (Chatterjee et al., 2007; Addo et al.
2011, El-Sorogy et al., 2016). Metals with EFs close to 1.0 are not enriched in the sediments,
are predominantly of natural origin and their associated sediments are considered
―uncontaminated‖. On the other hand, metals with high EFs are considered enriched in the
sediments, mainly of anthropogenic origin and their associated sediments are considered
―contaminated‖.
Since metal distribution in sediments can be influenced by variations in mineralogical
composition, grain size, organic matter and carbonate content of the sediments (Horowitz and
Elrick, 1987; Aloupi and Angelidis, 2001; Dung et al., 2013), normalisation is required when
deriving EFs in order to offset any anomaly in sediment metal distribution and allow a
comparison of EFs for different sediments to be made (Sinex and Helz, 1981; Aloupi and
Angelidis, 2001; Chatterjee et al., 2007; Addo et al., 2012; Yilgor et al., 2012; Dung et al.,
2013; Iqbal et al., 2013; Jiang et al., 2013; Mahu et al., 2015). Although metal normalisation
to the silt and clay fraction or analysis of sediments of similar grain sizes can offset the grain
size effect (Horowitz, 1985;Aloupi and Angelidis, 2001; Dung et al., 2013), normalisation to a
conservative metal such as Al (Aloupi and Angelidis, 2001; Chatterjee et al., 2007; Mahu et
al., 2015) or Fe (Sinex and Helz, 1981; Addo et al., 2012; Yilgor et al., 2012) can offset both
the grain size and mineralogical effects (Aloupi and Angelidis, 2001; Dung et al., 2013) and
is, therefore, incorporated in the derivation of the EF according to Eq. 1:
EF = [M/N]Sample/[M/N]Crust (1)
where [M/N]Sample is the metal/Fe or metal/Al ratio in the sediment sample and [M/N]Crust is
the same in the pre-impacted sediment.
Based on the EF value, the degree of metal enrichment is defined as follows: deficient (EF ≤
1), minor enrichment (1 < EF ≤ 3), moderate enrichment (3 < EF ≤ 5), moderately severe
enrichment (5 < EF ≤ 10), severe enrichment (10 < EF ≤ 25), very severe enrichment (25 < EF
≤ 50), and extremely severe enrichment (EF > 50).
The Igeo is derived according to Eq. (2):
Igeo = Log2 [Cn/(1.5 x Bn)] (2)
Literature Review
24
where Cn is the metal concentration in the sediment sample and Bn is the corresponding pre-
impacted metal concentration.
Using the Igeo does not require a compensation for the mineralogical effect (Dung et al., 2013).
Instead, a value of 1.5 is introduced as a background matrix correction due to lithogenic
effects (Muller, 1969; Addo et al. 2011; Iqbal et al. 2013; Mahu et al. 2015). Based on the Igeo
values, metal contamination in sediments is characterised as follows: uncontaminated (Igeo <
0), uncontaminated to moderately contaminated (0 ≤ Igeo < 1), moderately contaminated (1 ≤
Igeo < 2), moderately to highly contaminated (2 ≤ Igeo < 3), heavily contaminated (3 ≤ Igeo < 4),
highly to very highly contaminated (4 ≤ Igeo < 5), and very heavily contaminated (Igeo ≥ 5).
2.5.3. Human health and ecotoxicological risk characterisation
Assessment of the risk posed by contaminated sediments, i.e. the likelihood of sediment-
bound contaminants to cause adverse biological effects to human and non-human biota (Birch
and Hutson, 2009), is critical for the handling and management of contaminated sediments
(Burton, 2002; Birch and Hutson, 2009). The risk characterisation may differ for different
pollutants although in some cases, similar approaches are applicable. For radionuclides, risk
characterisation approaches include the use of radiological hazard indices and the ERICA
(Environmental Risk from Ionising Contaminants Assessment and Management) model. The
characterisation of the potential ecotoxicological risk posed by individual metals, OCP and
PAH pollutants in sediments commonly involves the use of biological effect-based numerical
sediment quality guidelines. The risk assessment code is also used to characterise the potential
risk of metals entering the food, while the total toxicity equivalence approach can be used to
evaluate the integrated risk posed by a mixture of PAH congeners in a sediment sample.
2.5.3.1. Radiological hazard indices and the ERICA model
Five radiological hazard indices (RHI), namely (1) total absorbed dose rate in air (D), (2)
radium equivalent activity (Raeq), (3) external hazard index (Hex), (4) annual gonadal dose
equivalent (AGDE), and (5) annual effective dose equivalent (AEDE) are commonly used to
assess the risk posed by radionuclide contamination to human health.
The D, measured in nanogray per hour (nGy.h-1
), expresses the rate of human exposure to
gamma radiation in air at 1m above the ground due to the activities of 226
Ra, 232
Th and 40
K in
Literature Review
25
the sediment samples. It is calculated by applying dose conversion factors or dose coefficients
for the specific activities of 226
Ra, 232
Th and 40
K, respectively, according to Eq. 3 (El
Mamoney and Khater, 2004):
D (nGy.h-1
) = 0.462ARa + 0.604ATh + 0.0417AK (3)
where ARa, ATh and AK are the specific activities (Bq.kg-1
dry wt.) of 226
Ra, 232
Th and 40
K,
respectively, in the sediment samples. The applied dose conversion factors for 226
Ra, 232
Th
and 40
K are 0.462, 0.604 and 0.0417, respectively, representing their dose rates in air per unit
specific activity (nGy.h-1
/Bq.kg-1
) in the sediment samples.
The Raeq is a weighted sum of the specific activities of 226
Ra, 232
Th and 40
K in the sediment
sample that allows comparison of the specific activities of different samples to be made with
respect to their 226
Ra, 232
Th and 40
K specific activities (El Mamoney and Khater, 2004),
assuming that 370 Bq.kg-1
of 226
Ra, 259 Bq.kg-1
of 232
Th and 4810 Bq.kg-1
of 40
K produce the
same gamma-radiation dose rates (Kurnaz et al., 2007). It is calculated based on Eq. 4 (El
Mamoney and Khater, 2004; Xinwei et al., 2006; Kurnaz et al., 2007):
Raeq (Bq.kg-1
) = ARa + 1.43ATh + 0.077AK (4)
where ARa, ATh and AK are the specific activities (Bq.kg-1
dry wt.) of 226
Ra, 232
Th and 40
K,
respectively, in the sediment samples.
The Hex is a measure of the indoor radiation dose rate associated with external gamma
radiation exposure from natural radionuclides in building materials, and is important when
considering the suitability of sediment for building material. It is calculated based on Eqn. 5
with the assumption of infinitely thick walls without windows or doors (Xinwei et al., 2006).
Hex = (ARa/370) + (ATh/259) + (AK/4810) (5)
where ARa, ATh and AK are the specific activities (Bq.kg-1
) of 226
Ra, 232
Th and 40
K,
respectively, in the sediment samples. To limit the radiation exposure to the permissible dose
equivalent limit of 1.5 mSv.y-1
, which is considered safe for humans, the value of Hex must not
exceed 1 (Xinwei et al., 2006; Kurnaz et al., 2007).
Literature Review
26
Owing to their relatively higher sensitivity to ionising radiation compared to other organs of
the body, the gonads are considered to be at a high risk of radiation exposure and are therefore
of great interest in radiological assessments (UNSCEAR, 2000; Xinwei et al., 2006; Kurnaz et
al., 2007). The AGDE, measured in microsievert per year (µSv.y-1
), estimates the potential
radiation dose that the gonads may receive from 226
Ra, 232
Th and 40
K. The sievert (Sv) is
another unit of radiation dose from the radiological protection point of view. Unlike the Gray,
it accounts for the relative biological effectiveness of different types of radiation (e.g. gamma
rays, alpha and beta particles), which are known to produce dissimilar magnitudes of
biological effects (Schmid and Schrader, 2007). The AGDE is calculated according to Eq. 6
(Xinwei et al., 2006; Kurnaz et al., 2007):
AGDE (µSv.y-1
) = 3.09ARa + 4.18ATh + 0.314AK (6)
where ARa, ATh and AK are the specific activities (Bq.kg-1
) of 226
Ra, 232
Th and 40
K,
respectively, in the sediment samples. The constants 3.09, 4.18 and 0.314 are conversion
factors expressed as µSv.y-1
/Bq.kg-1
.
The D can be converted to AEDE to assess the dose rate to an individual from outdoor gamma
radiation over a period of one year, taking into consideration an outdoor occupancy factor of
0.2 and an effective dose conversion factor of 0.7 Sv/Gy. It is calculated from Eq. 7 (Kurnaz
et al., 2007):
AEDE (µSv/y) = D (nGy/h) x 8760 (h/y) x 0.2 x 0.7 (Sv/Gy) x 10-3
(7)
For human health protection, the recommended values of D, Raeq, Hex, AGDE and AEDE are
55 nGy.h-1
, 370 Bq.kg-1
, 1, 300 µSv.y-1
and 70 µSv/y, respectively (Xinwei et al., 2006;
Kurnaz et al., 2007).
For assessment of the potential radioecological risks, the use of reliable models of wide
applicability is necessary (Ulanovsky et al., 2008). One such model is the ERICA, developed
by the European Commission (Larsson, 2008). The ERICA model provides an integrated
approach to the assessment and management of environmental risks from ionising radiation
(Beresford et al., 2007). A detailed description of the ERICA model can be found in literature
(Beresford et al., 2007; Brown et al., 2008; Larsson, 2008). The ERICA model can be used to
Literature Review
27
provide an overview of the potential radioactivity levels in biota and the dose rates they are
likely to receive based on the measured specific activities in the sediments.
2.5.3.2. The Sediment Quality Guideline approach
Various sediment quality guidelines (SQGs) have been developed around the world (Burton,
2002) for the characterisation of the potential ecotoxicological risk posed by metal, OCP and
PAH contamination in sediments. SQGs serve as national and international guidelines for the
disposal of dredged materials (Mamindy-Pajany et al., 2010). Among the widely used SQGs
are the effects-range low (ERL) and the effects-range median (ERM) values (Long et al.,
1995; Long et al., 1998; Long et al., 2006). These SQGs were empirically derived by
matching concentrations of chemical contaminants in sediments against biological effect data
(Long et al., 1995; Long et al., 1998). Long et al. (1998) reported a 10% incidence of adverse
biological effects in sediment-dwelling organisms when contaminant concentrations were
below the ERL, but > 75% incidence of adverse biological effects when contaminant
concentrations exceeded the ERM. Thus, the ERL and the ERM define the likelihood of a
chemical concentration in the sediment to cause adverse biological effect with good predictive
ability (Long et al., 1998).
The ERL and ERM define three concentrations ranges and their associated risks are
interpreted as follows: contaminant concentration at or below the ERL indicates low risk,
contaminant concentration above the ERL but below the ERM indicates moderate risk, while
contaminant concentration above the ERM indicates high risk (Birch and Hutson, 2009). The
use of SQGs can help identify contaminants of potential concern and areas of priority (Burton,
2002; Long et al., 2006; Birch and Hutson, 2009). Table 2.1 presents the ERL and ERM
values for some priority metals, OCPs and PAHs.
It has been recognised that several chemical contaminants are often present in sediments
(Casado-Martinez et al., 2006; Long et al., 2006), particularly harbour sediments (Birch and
Olmos, 2008; ; Birch and Hutson, 2009; Schipper et al., 2010), the combined toxicity of
which may potentially differ from those of the individual pollutants (Burton, 2002; Long et
al., 2006; Birch and Olmos, 2008). To predict the ecotoxicological risks from the combined
toxicity of the different pollutants present in a sediment sample, the mean ERM quotient
(mERMQ) is used (Long et al., 2006; Birch and Hutson, 2009). The mERMQs are derived by
Literature Review
28
normalising the concentrations of the individual contaminants to their respective ERMs, then
summing all the quotients and finding their average.
Table 2.1 ERL and ERM values (mg.kg-1 dw) for some priority PAHs, metals and
OCPs
*Long et al. (1995); Burton (2002)
Assumptions underlying the ERMQ approach are that (1) the different pollutants contribute
additively to the overall toxicity, rather than antagonistically or synergistically, and (2)
samples with the same mERMQ pose similar ecotoxicological risks (Long et al., 2006; Birch
and Hutson, 2009). Based on this approach, the potential ecotoxicological risk is characterised
as follows: minimal if mERMQ < 0.1, low if 0.1 ≤ mERMQ < 0.5, moderate if 0.5 ≤
mERMQ < 1.5, and high if mERMQ ≥ 1.5 (Birch and Hutson, 2009).
2.5.3.3. The total toxicity equivalence approach
PAHs are often present in sediments as complex mixtures of several congeners with wide-
ranging toxic and carcinogenic potentials (Nisbet and LaGoy, 1992; Neff et al., 2005; Escher
et al., 2008). In terms of toxicology, benzo[a]pyrene is the most extensively studied among
the PAH congeners and considered to be highly toxic and carcinogenic (Nisbet and LaGoy,
Contaminant ERL* ERM
* Contaminant ERL
* ERM
*
PAHs (µg.kg-1
) Metals (mg.kg-1
dw)
Acenaphthene 16 500 Cd 1.2 9.6
Acenaphthylene 44 640 Hg 0.15 0.71
Anthracene 85.3 1100 Ni 20.9 51.6
Fluorene 19 540 Pb 46.7 218
Naphthalene 160 2100 Cr 81 370
Phenanthrene 240 1500 Cu 34 270
Chrysene 384 2800 Zn 150 410
Fluoranthene 600 5100 As 8.2 70
Pyrene 665 2600
Benz[a]anthracene 261 1600 OCPs (µg.kg-1
)
Benzo[a]pyrene 430 1600 Total DDT 1.58 46.1
Dibenz[a,h]anthracene 63.4 260 p,p-DDE 2.2 27
Literature Review
29
1992; Escher et al., 2008). A toxic equivalency factor (TEF) of a PAH congener expresses its
toxicity relative to that of benzo[a]pyrene, which serves as the surrogate PAH and is assigned
a TEF value of 1.0 (Nisbet and LaGoy, 1992). The TEF values for the PAH16 according to
Nisbet and LaGoy (1992) are presented in Table 2.2.
Table 2.2 The USEPA 16 priority PAH congeners and their assigned TEF values
*Nisbet and LaGoy (1992)
For a quantitative evaluation of the integrated risk posed by a mixture of PAHs in a sediment
sample, the total toxicity equivalence (TEQ) is computed from the concentrations and TEFs of
the individual PAH congeners according to Eq. 8 (Escher et al., 2008; Nyarko et al., 2011c):
TEQ (mg.kg-1) = Σ(Cn x TEFn) (8)
where Cn and TEFn are, respectively, the concentration (mg.kg-1
) and TEF of an individual
PAH in the sediment sample.
The underlying assumptions of the TEQ approach are that the PAH congeners in the mixture
(1) exhibit the same mode of action and (2) contribute additively to the overall toxicity
(Escher et al., 2008). Based on the TEQ approach, sediment contamination is classified as
follows (Yang et al., 2014): uncontaminated (with potential no risk) if TEQ < 0.1 mg.kg-1
;
slightly contaminated (with potential medium risk) if 0.1 < TEQ < 1 mg.kg-1
; and significantly
contaminated (with potential high risk) if TEQ ≥ 1.0 mg.kg-1
.
PAH congener TEF* PAH congener TEF
*
Acenaphthylene 0.001 Anthracene 0.01
Fluorene 0.001 Benzo[ghi]perylene 0.01
Naphthalene 0.001 Benz[a]anthracene 0.1
Phenanthrene 0.001 Benzo[b]fluoranthene 0.1
Fluoranthene 0.001 Benzo[k]fluoranthene 0.1
Pyrene 0.001 Indeno[1,2,3-cd]pyrene 0.1
Acenaphthene 0.001 Benzo[a]pyrene 1.0
Chrysene 0.01 Dibenz[a,h]anthracene 5.0
Literature Review
30
2.5.3.4. Using the risk assessment code
Metals exist in different binding forms with different binding strengths, i.e. water-soluble and
exchangeable (bound to carbonates), reducible (bound to iron and manganese oxides) and
oxidisable (bound to sulphides or organic matter) forms (Díaz-de Alba et al., 2011; Kalwa et
al., 2013; Kelderman and Osman, 2007). These metal binding forms are associated with
different mobility, bioavailability and thus ecotoxicological potential (Calmano et al., 1993;
Jain, 2004; van Hullebusch et al., 2005; Dung et al., 2013; Kalwa et al., 2013; Pini et al.,
2015). Metals in the water-soluble and exchangeable form are the most weakly bound and,
therefore, pose the greatest risk of entering the food chain (Calmano et al., 1993; DelValls et
al., 2004; Jain, 2004; Kelderman and Osman, 2007; Dung et al., 2013; Iqbal et al., 2013;
Kalwa et al., 2013). The risk assessment code (RAC) has been developed to estimate the
potential risk of a sediment-bound metal entering the food chain based on the metal
fractionation in sediments (Jain, 2004; Zhu et al., 2012; Jiang et al., 2013). The RAC of a
given sediment-bound metal is expressed as the percentage of its concentration in the water-
soluble and exchangeable form according to Eq. 9:
RAC = [MWSE]/[MT] x 100% (9)
where [MWSE] is the concentration of a given sediment-bound metal in the water-soluble and
exchangeable form and [MT] is its total concentration.
Based on the value of the RAC, risk may be defined as follows (Jain, 2004; Zhu et al., 2012):
<1 % indicates no risk, 1-10 % indicates low risk, 11-30 % indicates medium risk, 31-50%
indicates high risk, and >50 % indicates very high risk.
A widely used analytical technique for metal fractionation in sediments is the 3-step
sequential extraction scheme developed by the European Standards, Measurements and
Testing Programme, formerly known as the Community Bureau of Reference (BCR)
(Quevauviller et al., 1994; Quevauviller et al., 1997; Rauret et al., 1999; Ptistišek et al., 2001;
Pueyo et al., 2001; Davidson et al., 2006). A major advantage of the 3-step BCR sequential
extraction method over other analytical techniques such as the 5-step sequential extraction
method by Tessier et al. (1979) or its modified versions (e.g. Kelderman and Osman, 2007) is
that it has been standardised by inter-laboratory comparison and the use of certified reference
Literature Review
31
materials (Quevauviller et al., 1994; Quevauviller et al., 1997; Rauret et al., 1999). Thus, the
BCR method can ensure greater quality assurance and control.
2.5.3.5. Limitations of the RHI, SQG, TEQ and RAC approaches
The RHI, SQG, TEQ and RAC approaches constitute a screening-level ecotoxicological risk
assessment, intended to predict the adverse biological effects of measured contaminants.
Screening-level ecotoxicological risk assessment provides a first line of evidence of (1) the
potential of measured contaminants to cause adverse biological effects, (2) contaminants of
potential concern, and (3) priority areas of concern (Long et al., 1998; Burton, 2002; Long et
al., 2006; Mamindy-Pajany et al., 2010), but is inadequate for a comprehensive assessment of
sediment pollution (Mamindy-Pajany et al., 2010). The RHI, SQG, TEQ and RAC approaches
may over or under estimate the potential hazard and impact of sediment-bound contaminants,
since they do not consider:
(1) Contaminant uptake and regulation (Rainbow, 2007; Rainbow and Luoma, 2011). The
RAC, for example, may not give a true reflection of metal bioavailability, which is
difficult to measure (DelValls et al., 2004) due to the potential for metal regulation by
organisms following uptake (Marsden and Rainbow, 2004; Rainbow, 2007; Rainbow and
Luoma, 2011).
(2) Synergistic or antagonistic effects of multiple contaminants on their overall toxicity
(Ciarelli et al., 1998; Burton, 2002; Simboura and Zenetos, 2002; Eggen et al., 2004;
Long et al., 2006).
(3) Chronic effects that may result from exposure to low contaminant concentration over a
long time and multiple effects that may be induced by a single contaminant (Eggen et al.,
2004).
(4) Sediment contaminants that have not been characterised for their toxicity (Schipper et al.,
2010).
(5) The entire spectrum of potentially toxic contaminants that is present in the sediment as it
is difficult to measure (Escher et al., 2008) since their measurement is not practical, and
SQGs have not yet been developed for all potential pollutants in sediments including the
COEC (Long et al., 1995; Burton, 2002; Long et al., 2006; Schipper et al., 2010).
Literature Review
32
2.5.4. Hazard/Toxicity and impact assessment
Hazard/toxicity and impact assessment is intended to evaluate biological responses to
chemical toxicity in sediments. Whole-sediment toxicity bioassays, which involve exposure of
relevant organisms to contaminated sediments under controlled conditions and measurement
of biological responses/endpoints (Ciarelli et al., 1998; Forrester et al., 2003; DelValls et al.,
2004), are an important tool in hazard and impact assessment of contaminated sediments
(DelValls et al., 2004; Annicchiarico et al., 2007; Casado-Martinez et al., 2007; Escher et al.,
2008; Morales-Caselles et al., 2009; Ré et al., 2009; Schipper et al., 2010; Prato et al., 2015).
The major advantage of whole-sediment toxicity bioassays over the RHI, SQG, TEQ and
RAC approaches is that they integrate the toxic effects of all contaminants present in a
sediment sample (Forrester et al., 2003; Escher et al., 2008) and provide a further line of
evidence of the potential ecotoxicological effects of contaminated sediments (Long et al.,
2006; Morales-Caselles et al., 2008; Schipper et al., 2008; Morales-Caselles et al., 2009).
Thus, whole-sediment toxicity bioassays are now required in many developed countries such
as Spain, Belgium, Germany (DelValls et al., 2004; Casado-Martinez et al., 2007), the
Netherlands (Casado-Martinez et al., 2006), Australia (Rose et al., 2006; van Dam et al.,
2008) and Italy (Prato et al., 2011) for adequate assessment of dredged sediments to support
the licensing of their subsequent disposal.
For a successful whole-sediment toxicity bioassay, there is a need to identify suitable test
organisms with measureable biological responses/endpoints that can discriminate between
different levels of chemical toxicity in sediments (Ciarelli et al., 1998). These endpoints
include acute effects such as mortality, sub-lethal and/or chronic effects such as growth and
reproduction or bioaccumulation (Forrester et al., 2003; DelValls et al., 2004; Annicchiarico
et al., 2007; Morales-Caselles et al., 2008; Schipper et al., 2008). The bioaccumulation
assessment is intended to give an indication of the bioavailability of sediment-associated
chemical contaminants and their potential for transfer along the food chain (DelValls et al.,
2004). The criteria for the selection of test organisms include their importance and abundance
in the ecosystem under investigation (Connon et al., 2012). For estuarine and marine whole-
sediment toxicity bioassays, algae, molluscs, sea urchins, amphipods and polychaetes have
been widely used as test organisms. Commercial acute sediment toxicity bioassay kits such as
Microtox®, which is based on the natural bioluminescence inhibition of the marine bacteria V.
Literature Review
33
fischeri, are also used (Morales-Caselles et al., 2007; Libralato et al 2008; Morales-Caselles et
al., 2009). Table 2.3 presents examples of sediment bioassay tests in use around the world.
Table 2.3 Test organisms used in sediment bioassay tests around the world
Sediment bioassay test
organisms
References
Bacteria (Microtox®) Beg and Ali, 2008; Libralato et al., 2008; Morales-
Caselles et al., 2007, 2009; Ghirardini et al., 2009; Baran
and Tarnawski, 2013
Amphipod Casado-Martinez et al., 2007; Scarlett et al., 2007; van
den Heuvel-Greve et al., 2007; Morales-Caselles et al.,
2007; Mayor et al., 2008; Ré et al., 2009; de-la-Ossa-
Carretero et al., 2012; Hanna et al., 2013.
Algae Oehlmann, 2002; Mariño-Balsa et al., 2003; Chen et al.,
2009
Sea urchin Stronkhorst et al., 1999; Schipper et al., 2008; Pagano et
al., 2017a, b.
Molluscs Oehlmann, 2002; Mariño-Balsa et al., 2003
Polychaetes Thain and Bifield, 2002; Casado-Martínez et al., 2006;
Moreira et al., 2006; Mayor et al., 2008; Kalman et al.,
2012
Among the various test organisms, the amphipod Corophium volutator (Stronkhorst et al.,
2003; Casado-Martinez et al., 2007; Scarlett et al., 2007; van den Heuvel-Greve et al., 2007;
Morales-Caselles et al., 2007; Mayor et al., 2008) and the polychaete Hediste diversicolor
(Casado-Martínez et al., 2006; Moreira et al., 2006; Mayor et al., 2008) have gained
popularity. The popularity of C. volutator (Fig. 2.7a) is mainly due to the following reasons
(Ciarelli et al., 1998; Roddie and Thain, 2002; Scaps, 2002; Bat, 2005): (1) it is available in
the field throughout the year, (2) it is easy to collect and maintain under laboratory conditions,
(3) it shows tolerance to a wide range of salinities, sediment grain sizes and organic carbon
contents, and (4) a standard protocol has been developed using C. volutator (Roddie and
Thain 2002; Schipper et al., 2006). H. diversicolor (Fig. 2.7b) is also preferred as a test
organism mainly due to the following attributes (Scaps, 2002; Philippe et al., 2008): (1) it
Literature Review
34
commonly occurs in intertidal areas, (2) it is able to survive in hypoxic and contaminated
environments, (3) it is tolerant to wide fluctuations in salinity and temperature, and (4) a
standard protocol has been developed using H. diversicolor (Hannewijk et al., 2004).
Furthermore, both C. volutator and H. diversicolor have wide geographic distributions and
can be found in polar, temperate and tropical marine regions (Bat, 2005; Moreira et al., 2006;
Uwadiae, 2010; Carvalho et al., 2012). However, whole-sediment toxicity bioassays with
tropical species are not yet well developed (Adams and Stauber, 2008).
Fig. 2.7 (A) Corophium volutator (http://www.aquatonics.com/Corophium.jpg); (B)
Hediste diversicolor (https://www.flickr.com/photos/gwylan/2170368562/) used as test
organisms in Chapter 6.
By using whole-sediment toxicity bioassays, the potential hazard and impacts are evaluated by
comparing measured biological responses with corresponding responses using
uncontaminated (control/reference) sediments under similar conditions (Stronkhorst et al.,
2003; DelValls et al., 2004; Mamindy-Pajany et al 2010) and applying established guidelines
(Thain and Bifield, 2002; Roddie and Thain, 2002; Casado-Martinez et al., 2007; ICES,
2008). Whole-sediment toxicity bioassays can help identify contaminated areas (Ciarelli et al.,
1998), but they cannot provide information on the contaminants responsible for sediment
toxicity (Escher et al., 2008). This can be achieved by integrating whole-sediment toxicity
bioassays with chemical analysis (Annicchiarico et al., 2007; Casado-Martinez et al., 2007;
Morales-Caselles et al., 2007, 2008; Escher et al., 2008; Mamindy-Pajany et al., 2010; Prato et
al., 2011). This integrated approach is required to better characterise the hazard, risk and
A B
Literature Review
35
impact of contaminated sediments (Morales-Caselles et al., 2008; Schipper et al., 2008;
Mamindy-Pajany et al., 2010) and are incorporated into regulatory programmes in many
developed countries (Ciarelli et al., 1998). Moreover, the use of a battery of whole-sediment
bioassays (DelValls et al., 2004; Morales-Caselles et al., 2009) with different test species
having potentially different sensitivities to chemical toxicity is recommended for the purpose
of managing dredged materials (Annicchiarico et al., 2007; Casado-Martinez et al., 2007;
Escher et al., 2008; Ré et al., 2009; Schipper et al., 2010; Prato et al., 2011; Prato et al., 2015).
2.6. Sedimentation in harbours
2.6.1. Sediment fluxes in harbours
Sediments play an important role in the ecological functioning of aquatic ecosystems,
providing food for filter-feeding invertebrates (Schipper et al., 2008; Jiang et al., 2013) and
spawning areas for many organisms (Prato et al., 2011). However, high influx of sediments
can cause ecological problems such as smothering of benthic eggs and larvae, reduced light
availability, and release of associated pollutants into the water column (Green and Coco,
2014). Sediment influx into coastal harbours is driven by natural factors such as tides, waves
(Leys and Mulligan, 2011), riverine sediment discharge (Akrasi, 2011) coupled to
anthropogenic factors such as sand winning (Kusimi and Dika, 2012).
The concentrations and fluxes of sediments in the water column can also influence the
dynamics and transport of particle-reactive pollutants in aquatic ecosystems (James, 2002;
Syvitski, et al., 2005; Lepland et al., 2010; Luo et al., 2010; George et al., 2012; Souza and
Lane, 2013). Thus, sedimentation provides a means of pollutant transport to and subsequent
accumulation in bottom sediments. In depositional environments, the continuous deposition of
sediments without an interruption in the sedimentary sequence can serve as an archive of
environmental changes (Kannan et al., 2005; Giuliani et al., 2008; Giuliani et al., 2015) and
dating of sediment cores can provide a historical record of SARs and pollution events
(Giuliani et al., 2008; Tang et al., 2008; Díaz-Asencio et al., 2009; Smith et al., 2009; Lepland
et al., 2010; Bellucci et al., 2012).
Coastal harbours tend to have low-energy hydrodynamics and restricted water movement due
to their breakwaters (Mestres et al., 2010). This facilitates the deposition and subsequent
accumulation of sediments within the harbour basins (Lepland et al., 2010; Luo et al., 2010).
Literature Review
36
Sediment accumulation within harbour basins is a major issue as it results in siltation and
poses navigational problems (Syvitski, et al., 2005; Van Rijn, 2005; Green and Coco, 2014).
Many harbours around the world have been affected by siltation, resulting in costly dredging
of several million tonnes of sediments to maintain appropriate water depths for safe
navigation and/or removal of contaminated sediments (Qu and Kelderman, 2001; Barneveld
and Hugtenburg, 2008; Schipper et al., 2010). The assessment of settling fluxes (SFs) and
SARs can provide complementary information for understanding sedimentation processes in
harbours (Liu et al 2014), which is necessary for harbour management (Buesseler et al., 2007;
Leys and Mulligan, 2011).
2.6.2. Quantification of SFs
Sediment traps in the form of close-ended cylindrical tubes are important tools for the
collection and assessment of settling particulate matter (and its associated pollutants) falling
vertically through the water column to the bottom sediments (Hakanson, 2006; Buesseler et
al., 2007; de Vicente et al., 2010; Kelderman et al., 2012; Santos-Echeandía et al., 2012; Liu
et al., 2014; Szmytkiewicz and Zalewska, 2014; Helali et al., 2016). The quantity of
particulate matter collected by the traps depends on the deployment period and the efficiency
of trap collection (Hakanson, 2006). Sediment traps are deployed typically over a period of
two weeks to allow sufficient particulate matter to be collected for analysis, while ensuring
minimal organic matter decomposition (Hakanson and Jansson, 1983; Buesseler et al., 2007;
Kelderman et al., 2012). Trap efficiency can be optimised through appropriate trap design.
Sediment traps with aspect ratios (i.e. height/diameter) greater than 5 minimise current-
induced resuspension within the traps and enhance the efficiency of traps to collect and
accumulate settling particulate matter (Bloesch and Burns, 1980; Kelderman et al., 2012; de
Vicente et al., 2010). The sediment trap-derived SF is expressed as the mass of dry material
deposited per unit area per unit time, i.e. mg.m-2
.d-1
or g.m-2
.y-1
. A schematic presentation of
sediment trap deployment in Chapters 7 and 8 is shown in Fig. 2.8.
Literature Review
37
Fig. 2.8 Schematic presentation of sediment trap deployment used as samplers for
settling particulate matter in Chapters 7 and 8
2.6.3. Quantification of SARs
In harbours, reservoirs, estuaries and coastal areas, bathymetric data such as tidal levels, water
depth and positioning acquired at different periods can be used to quantify SARs with the
application of a series of corrections (Khaba and Griffiths, 2017; Brucker et al., 2007). For
shallow waters with less than 20 m water depth such as harbours, bathymetric data can be best
obtained by using Phase Differencing Bathymetric Sonar (PDBS) systems owing to their
associated total vertical uncertainty of 0.26 m for a 10 m water depth (Brisson et al., 2014).
This uncertainty is acceptable for water depth control purposes, but it is too coarse for
estimating SARs. Therefore, PDBS systems are usually suitable for mapping SARs in areas
Water surface Buoy
Sediment traps
Accumulated settling particulates
Rigid anti-rust coated metallic frame
String
Sea bed
Anchor
Literature Review
38
where accretion rates are high, exceeding 0.3 m.y-1
(Brucker et al., 2007) with time lapses of
the order of decades (Ortt et al., 2000). This method provides mean SAR in the time lapse and
cannot provide information on processes affecting the depth distribution of chemical
pollutants. In this regard, particle-reactive radionuclides such as 210
Pb have found useful
applications in the study of sedimentary processes and quantification of SARs (Erten, 1997;
Caroll and Lerche, 2003; Giffin and Corbett, 2003; Corbett et al., 2009). Non-radioactive
dating methods based on e.g. fossil markers and pollen can provide important stratigraphic
time-markers, but in contrast to the radiometric dating methods, these are of limited
applicability and cannot determine absolute chronologies of sediments (Carroll and Lerche,
2003; Abril, 2015).
2.6.3.1. 210Pb as a tool for the quantification of SARs
The 210
Pb radioisotope, based on its short half-life of 22.3 years, is particularly suitable for
chronological assessment and quantification of recent sedimentation rates on time-scales
spanning the past 100-150 years (Lu, 2007; Appleby, 2008; Díaz-Asencio et al., 2009). Alpha
spectrometry and low background gamma spectrometry are the most common methods of
analysing the specific activity of 210
Pb in sediments (Sikorski and Bluszcz, 2008; de
Vleeschouwer et al., 2010; Mabit et al., 2014) with comparable results (Zaborska et al., 2007;
Sikorski and Bluszcz, 2008).
The 210
Pb radioisotope is a member of the 238
U-decay series and may be produced from the
decay of 222
Rn in the atmosphere referred to as unsupported/excess 210
Pb or 210
Pbexc (Erten,
1997; Alonso-Hernandez et al., 2006; Lu, 2007). The in situ radioactive decay of 226
Ra in the
water column also produces 210
Pb referred to as supported 210
Pb or 210
Pbsupp (Oldfield and
Appleby, 1984; Lu, 2007; Appleby, 2008; Nehyba et al., 2011; Abril and Brunskill, 2014).
The 210
Pbsupp is assumed to be in secular equilibrium with 226
Ra and other members of the
decay chain preceding it, while the 210
Pbexc represents that part of the measured total 210
Pb
specific activity in sediment that exceeds the specific activity in secular equilibrium with
226Ra (Pfitzner et al., 2004; Hollins et al., 2011). The fluxes of
210Pb in sediments are linked to
wet and dry atmospheric deposition (Erten, 1997; Appleby, 2008; Pfitzner et al., 2004; Mabit
et al., 2014) as well as surface run-off and erosion from the catchment (Mabit et al., 2008;
Ruiz-Fernández et al., 2009). The sources and pathways of 210
Pb inputs in aquatic systems are
shown in Fig. 2.9.
Literature Review
39
Fig. 2.9 Sources and pathways of 210Pb inputs in aquatic systems
(http://www.ozcoasts.gov.au/glossary/images/pb210_diagram.jpg)
In aquatic systems, 210
Pbexc is scavenged by particulate matter, particularly the silt-clay
fraction of sediments (Pfitzner et al., 2004), and subsequently accumulates in bottom
sediments (Erten, 1997). The optimal material for 210
Pb dating is undisturbed sediments
(Santschi et al., 2001; Bellucci et al., 2012). For 210
Pb dating of sediment cores, it is assumed
that the 210
Pbsupp is at equal specific activity with its parent 226
Ra nuclide and is constant down
the sediment core profile, while the 210
Pbexc decays because it is not supported by 226
Ra via
222Rn (Erten, 1997). The
210Pbexc specific activity in the sediment core is obtained as the
difference between the measured total 210
Pb specific activity and the 210
Pb specific activity in
equilibrium with 226
Ra (Erten, 1997), which usually occurs in the deep layers (Appleby and
Oldfield, 1978). 210
Pbexc decays in accordance with the radioactive decay law (Lu, 2007;
Appleby, 2008) and can be described by Eq. (10):
A = A0e-λt
(10)
where A0 is the initial specific activity of 210
Pbexc, A is the specific activity of
210Pbexc after
time t, and λ is the decay constant of 210
Pb (0.03114 y-1
).
Literature Review
40
An undisturbed sedimentary sequence is thus characterised by an exponential decrease in
210Pbexc activity down the sediment core (see Fig. 2.10); the vertical
210Pbexc profile being a
function of the sediment accumulation rate (Alonso-Hernandez et al., 2006; Appleby, 2008).
Fig. 2.10 210Pbexc activity profile in an undisturbed sediment core (Mackenzie et al.,
2011)
2.6.3.2. 210Pb-based sediment dating models
Three widely used 210
Pb sediment dating models are the Constant Flux Constant
Sedimentation (CF-CS), Constant Rate of Supply (CRS) and Constant Initial Concentration
(CIC) models (McDonald and Urban, 2007; Appleby, 2008). The CIC and CRS models
(Appleby and Oldfield, 1978; Robbins, 1978) are, however, considered as the two standard
approaches (Appleby, 2004; Appleby, 2008; Nehyba et al., 2011). These 210
Pb sediment
dating models convert the 210
Pbexc specific activities in sediment layers into numerical ages to
obtain an age-depth profile of sediment chronologies (Gunten et al., 2009).
2.6.3.2.1. The Constant Flux Constant Sedimentation (CF-CS) model
The CFCS model is a common particular case of CIC and CRS models. The CF-CS model
applies under the following assumptions: (1) a constant flux of 210
Pbexc from the atmosphere
and a constant dry-mass sedimentation rate (Appleby and Oldfield, 1983; Díaz-Asencio et al.,
2009) and (2) no post-depositional sediment mixing with every sediment layer having the
Literature Review
41
same initial 210
Pbexc specific activity (Appleby and Oldfield, 1983). Under these situations, the
210Pbexc
specific activity varies exponentially in accumulated sediments (Appleby and
Oldfield, 1983; Appleby, 2004; McDonald and Urban, 2007; Nehyba et al., 2011). Due to
potential effects of sediment compaction, the 210
Pbexc specific activity is related to the mass-
depth (g.cm-2
) instead of the linear-depth of the sediment core (Erten, 1997; Lu, 2007). Thus,
under the CF-CS model, the expected specific activity at a given mass-depth, m, is given by
Eq. 11 (Erten 1997; McDonald and Urban, 2007):
Ax = A0 e-λm/w
(11)
where Ax (Bq.kg-1
) is the 210
Pbexc specific activity at mass-depth x; A0 (Bq.kg-1
) is the initial
210Pbexc specific activity at x = 0; m is the cumulative dry-mass (g.cm
-2), λ is the decay
constant for 210
Pb ( 0.03114) and w is the mass sedimentation rate (g.cm-2
.y-1
).
A logarithmic plot of the 210
Pbexc specific activity versus mass depth will generate a linear
profile with slope = - λ/w, from which the mass sedimentation rate, w, can be calculated (e.g.
see Fig. 2.11).
Fig. 2.11 A logarithmic plot of the 210Pbexc specific activity versus mass depth (Díaz-
Asencio et al. 2009)
Literature Review
42
2.6.3.2.2. The Constant Initial Concentration (CIC) model
The main assumption of the CIC model (Robbins, 1978; Appleby and Oldfield, 1978) is that
the initial 210
Pbexc specific activity (A0) at the sediment-water interface remains constant over
time with a constant sedimentation (Appleby, 2008; Nehyba et al., 2011), but allows co-
variation of both 210
Pbexc flux and sedimentation (Appleby, 2008). If these assumptions apply,
A0 will decline exponentially with age so that the 210
Pbexc specific activity in a sediment layer
of age t (At) is given by Eq. 12:
At = A0 e-λt
(12)
where A0 is the 210
Pbexc specific activity (Bq.kg-1
) at time zero, which in the absence of surface
mixing represents the concentration at the sediment-water interface; At is the 210
Pbexc specific
activity (Bq.kg-1
) after time t and λ is the radioactive decay constant for 210
Pb (0.03114 y-1
).
Eq. 12 can be rewritten as Eq. 13 and used to calculate the age (t) of a sediment layer at a
depth x (Appleby and Oldfield, 1978):
t = 1/λ ln[A0/Ax] (13)
If it is assumed that the sedimentation rate (S) is constant within the sediment layer x, then the
period over which the sediment has accumulated is t = x/S. Substituting t = x/S into Eq. 13 and
re-arranging Eq. 13 gives Eq. 14:
(1/x) ln [Ax/A0] = - λ/S (14)
A linear regression profile of ln(Ax) versus depth (x) is expected to produce a slope = - λ/S,
from which S can be computed according to Eq. 15:
S = - λ / slope (15)
Application of the CIC model seems difficult within an industrial harbour such as the Tema
Harbour, considering the changing industrial activities and harbour configuration, which
could lead to varying proportions of sediment constituents and then to varying initial
concentrations of unsupported 210
Pb.
Literature Review
43
2.6.3.2.3. The Constant Rate of Supply (CRS) Model
The CRS model (Appleby and Oldfield, 1978; Robbins, 1978) assumes: (1) a constant rate of
210Pbexc supply to the sediments despite variations in the dry-mass sedimentation rate and (2)
no post-depositional mixing (McDonald and Urban, 2007). Thus, the CRS model allows
changes in sedimentation rates while estimating sediment ages (Appleby, 2008; Nehyba et al.,
2011; de Souza et al., 2012). Sediment ages are derived from the fraction of the depth-
integrated 210
Pbexc present above the core depth considered. Thus, any deviation from an
exponential decrease with depth of 210
Pbexc is interpreted by the CRS model to reflect a
variation of the sedimentation rate (Appleby, 2004; MacKenzie et al., 2011; Nehyba et al.,
2011). Important considerations for use of the CRS model are (1) an inverse relationship
between the initial concentration and the sedimentation rate, (2) a non-monotonic decrease in
210Pb activity and (3) the
210Pb dating horizon (i.e. the depth where the
210Pbexc specific
activity is diminished and 210
Pbsupp specific activity becomes constant) is reached (Appleby,
2008). Using the CRS model, the age (t) of sediments at a depth x can be estimated from Eq.
16 (Appleby and Oldfield, 1978; Erten, 1997; MacKenzie et al., 2011; de Souza et al., 2012):
t = (1/λ) ln[A∞/Ax] (16)
where A∞ is the integrated 210
Pbexc (210
Pbexc inventory) of the entire sediment column and Ax is
the integrated 210
Pbexc below a depth x of the sediment core.
The dry mass sedimentation rate (w, with a unit of g.cm-2
.y-1
) can be obtained for each two
adjacent layers from Eq. 17 (Appleby and Oldfield, 1978):
w = λAx/C (17)
where C is the 210
Pbexc specific activity at the depth x.
If a steady state supply of 210
Pbexc to the sediment is assumed, then the inventory of 210
Pbexc
can be estimated using Eq. 18:
I0 = Σ(Ai ρi hi) (18)
Literature Review
44
where I0 is the 210
Pbexc inventory in the sediment (Bq.cm-2
); Ai is the 210
Pbexc specific activity
for sediment layer i (Bq.g-1
), ρi is the bulk density of sediment layer i (g.cm
-3) and hi is the
thickness of sediment layer i (cm).
The flux of 210
Pbexc to the sediment (F) can be estimated from Eq. 19:
F = λ I0 (19)
2.6.3.3. The Time Estimates from Random Entries of Sediments and Activities
(TERESA) model
It has been shown that the assumption of an ideal deposition, i.e. the deposition of new
radioactive inputs above the previously existing material at the sediment-water interface
(SWI), of the conventional 210
Pb dating models is unrealistic, particularly in sediment cores
with very high porosities (Abril and Gharbi, 2012). Thus, using statistical analysis of a
database of laminated sediment cores, Abril and Brunskill (2014) reconstructed historical
records of initial 210
Pbexc specific activity, 210
Pbexc flux onto the SWI and SARs, which
revealed wide temporal fluctuations. Their results also showed a linear relationship between
the 210
Pbexc fluxes and SAR. However, no statistically significant correlation was found
between the initial 210
Pbexc specific activity and SAR, which conflicts with the assumption of
most 210
Pb-based radiometric dating models. This paved the way for the development of the
TERESA model (Abril, 2016).
The TERESA model is based on the findings that (1) the flux of 210
Pbexc to the SWI varies
with time and (2) the flux of 210
Pbexc is governed by the flux of matter instead of direct
atmospheric 210
Pbexc deposition, resulting in a statistically significant correlation between the
flux of 210
Pbexc and the flux of matter/sediment accumulation rates (Abril and Brunskill,
2014). Other important assumptions in the application of the TERESA model are that (1)
210Pbexc is a particle-bound tracer, which is continually deposited onto the SWI, (2) no post-
depositional redistribution occurs and (3) the sedimentary sequence is continuous with none
of its layers missing.
The TERESA model works with continuous probability distributions for initial 210
Pbexc
specific activities (A0) and SAR and, therefore, assumes there are neither flood layers nor
Literature Review
45
other instantaneous inputs to the sediment column (Abril, 2016). Thus, a sediment core cut
into N slices (labelled i = 1, 2, … N) is assumed to have resulted from the accumulated mass
flow onto the SWI over the time interval ∆Ti with an average mass flow (SAR) value of wi
(Abril, 2016). If w is the magnitude of the arithmetic mean of all the wi for the N slices, then
the values of wi are almost normally distributed around w with a standard deviation σw (Abril
and Brunskill, 2014). This results in a linear correlation between the 210
Pbexc fluxes and SAR.
Thus, each sediment slice can be characterised by a pair of values (A0,i, wi), the sequence of
which produces the 210
Pbexc vertical profile, the chronology and the particular SAR history
(Abril, 2016).
It is worthy to note that for the TERESA model, the mass depth m (with physical dimensions
M.L-2
) is a more appropriate magnitude than the linear depth (with physical dimension L) due
to (1) compaction during the sediment accretion and (2) core shortening during the coring
operation and later handling (Abril, 2016). Moreover, each sediment slice of mass thickness
∆mi should be provided with its respective uncertainty, derived from the experimentally
averaged specific 210
Pbexc specific activities Ai(m) (Abril, 2016).
Abril (2016) has validated the TERESA model using synthetic and real data from laminated
sediment cores from the Santa Barbara Basin (Koide et al., 1973) and the Sihailongwan Lake,
China (Schettler et al., 2006a, 2006b), for which independent chronology has been
established. Prior to this thesis, the potential of the TERESA model for dating recent
sediments from environments where the conventional 210
Pb-based dating models face
constraints such as coastal harbours had not been explored.
2.6.3.4. Validation of 210Pb dating models
For any of the 210
Pb dating models, a validation of the 210
Pb-based sediment chronology by
other time markers is necessary (Smith, 2001; Abril, 2004; Appleby, 2004) and errors
associated with the estimated sediment ages and sedimentation rates should be quantified. The
short-lived 137
Cs isotope (T1/2 = 30.1 y) has been commonly used to validate 210
Pb dates of
sediment cores (Erten 1997; Smith, 2001; Appleby, 2002; Pfitzner et al., 2004; Alonso-
Hernandez et al., 2006; McDonald and Urban, 2007; Díaz-Asencio et al., 2009; Smith et al.,
2009; Lepland et al., 2010; Giuliani et al., 2011), which can be measured directly by gamma
spectrometry (Bellucci et al., 2012; Díaz-Asencio et al., 2009; Lepland et al., 2010; Smith et
al., 2009). The main sources of global 137
Cs contamination are nuclear weapon tests carried
Literature Review
46
out in the Northern and Southern hemispheres in the 1950s and 1960s and the accident at the
Chernobyl nuclear power plant in Ukraine on April 26, 1986. Thus, the highest 137
Cs peaks in
sediments correspond to these periods (Abril and Garcia-Le6n, 1994; Erten, 1997; Di
Leonardo et al., 2007; Erten, 2011) and serve as a validating tool in 210
Pb dating of sediments
(Smith, 2001; Gunten et al., 2009).
2.6.3.5. Challenges of quantifying sediment SARs using the 210Pb dating models
Contrary to the assumption of uniform sedimentation, non-uniform deposition of sediments
may occur in reality and present a challenge to accurate dating of sediment cores using the
common 210
Pb models. Episodic delivery of sediments and associated tracers into sedimentary
systems through events such as flooding and turbidity currents may result in a significantly
higher than normal rate of 210
Pb supply (Appleby, 1997), a situation that can place a restriction
on 210
Pb dating of sediment cores (Appleby, 2008) since the underlying assumptions of
constant concentration and flux for the CIC and CRS models are conflicted and lead to errors
in the sediment chronology (Appleby, 1997; Marques Jr. et al., 2006). In situations where
there have been significant variations in the sedimentation, both the CIC and CRS models are
inapplicable for deriving chronologies (Appleby, 2008). In such situations, the CRS model
may only be applicable if the sediment core is analysed in a piecewise fashion using 137
Cs and
241Am chronostratigraphic dates as reference levels to derive accurate chronology for different
sections of the core (Appleby, 2008).
Low activities of 137
Cs in sediments may compromise the reliability of the 210
Pb-derived
sediment chronologies (Arnaud et al., 2006; Lepland et al., 2010). Moreover, in more complex
depositional settings, the lack of a significant yearly deposition maximum of 137
Cs (Pfitzner et
al., 2004) or the lack of distinct 137
Cs peaks (Abril and Garcia-Le6n, 1994) can result in a
restricted use of 137
Cs in deriving sediment chronology and sedimentation rates. Therefore, the
use of several independent sediment dating methods instead of only one method is
recommended, since it can offset the limitations encountered when using only one dating
method (Abril, 2004). In situations where different models (e.g. the CIC and CRS models)
yield different results or neither of the results of the models is consistent with the 137
Cs results,
the use of more robust models is recommended to aid the interpretation of the dating results
(Smith, 2001; Appleby, 2004).
Literature Review
47
The assumption of no post-depositional mixing of sediments may also not be met in the real
environment due to physical, chemical and biological (bioturbation) processes (Abril et al.,
1992; Appleby, 1997; Schmidt et al., 2007b), which can potentially alter the original
distribution of tracers in the sediments (Santschi et al., 2001) and cause difficulties in
establishing accurate sediment chronology. The presence or absence of post-depositional
sediment mixing can be assessed by examining the profiles of short-lived and particle-reactive
radionuclides such as 234
Th (half-life = 24.1 d) and 7Be (half-life = 53.3 d) in sediment cores
(Erten, 1997; Schmidt et al., 2007a, b). 234
Th is produced from the decay of the soluble and
long-lived parent 238
U (half-life = 4.5 x 109 y), while
7Be is a cosmogenic radionuclide
produced from the interaction of cosmic rays with oxygen and nitrogen in the stratosphere and
the troposphere (Erten, 1997; Pfitzner et al., 2004; Mabit et al., 2014). 7Be enters aquatic
systems via direct wet and dry deposition or indirectly via transport of surface soil from the
catchment through run-off (Pfitzner et al., 2004; Mabit et al., 2014). Due to their short half-
lives, 234
Th and 7Be can provide reliable information on sediment mixing occurring within a
few months (Schmidt et al., 2007a). Subsurface occurrence of 234
Th and 7Be in areas of low
sedimentation rates may indicate post-depositional sediment mixing (Schmidt et al., 2007b).
The supply of 210
Pbexc and 137
Cs into bottom sediments is controlled by many complex
processes (Abril et al., 1992; Abril and Garcia-Le6n, 1994; Appleby, 2008) that affect
redistribution of sediment-bound tracers in confounding ways (Abril et al., 1992; Appleby,
2008; Mabit et al., 2014). For example, atmospheric 210
Pb and 137
Cs may first deposit onto
soils and subsequently transported into aquatic systems (Abril and Garcia-Le6n, 1994; Mabit
et al., 2014), in which case the flux of matter into the aquatic system will exert a greater
control on the 210
Pbexc flux onto the bottom sediments than direct atmospheric 210
Pbexc
deposition (Abril and Brunskill, 2014). Since the fluxes of matter is affected by storm runoff,
floods and tidal events (Palinkas et al., 2005; Díaz-Asencio et al., 2009), which may be site-
and time-specific, the application of a particular model at different sites would require a case
by case assessment of sediment cores (Appleby and Oldfield, 1983; Abril and Brunskill,
2014). Moreover, the assumption of no post-depositional mobility of sediment-bound tracers
under the application of 210
Pb dating models may also not hold in reality due to potential
diffusion and advection of the tracers within the sediment pore water (Appleby and Garcia-
Le6n, 1997) under the influence of the sediment porosity (Abril and Gharbi, 2012). An
indication of post-depositional migration of sediment-bound radiotracers from surface layers
Literature Review
48
into deeper layers through the sediment pores is the occurrence of maximum concentrations of
radiotracers in subsurface layers rather than at the SWI (Abril and Gharbi, 2012).
2.7. Conclusions
Chemical pollution and sedimentation in the marine environment are major problems as they
threaten human and ecological well-being and thus, their assessments have been the focus of
many studies. Coastal harbours associated with industrial and urban centres are susceptible to
chemical pollution and sedimentation. Chemical pollutants primarily bind to sediments upon
entry into aquatic environments due to their particle-reactive nature, making sediments an
important tool for chemical pollution assessment. Approaches such as radiological hazard
indices and the ERICA model (for radionuclides), the enrichment factor, geo-accumulation
index and the risk assessment code (for metals), biological effect-based numerical sediment
quality guidelines (for e.g. metals, OCPs and PAHs) and the total toxicity equivalence can be
used to provide a first line of evidence of chemical contamination in sediments. The inclusion
of a battery of toxicity bioassays is now recommended as a further line of evidence to
adequately characterise chemical pollution in sediments.
Quantifying sedimentation rates commonly involve the use of 210
Pb dating models such as the
Constant Flux Constant Sedimentation, the Constant Initial Concentration and the Constant
Rate of Supply models. In disturbed sedimentary systems such as coastal harbours where the
delivery of sediments and 210
Pb may be controlled by complex processes, there is a potential
limitation of the applicability of the 210
Pb dating models for the quantification of
sedimentation rates. It is evident from the literature that integrated approaches are required to
overcome such limitations to allow the quantification of sedimentation rates in non-ideal
sedimentary environments. This requires more rigorous sampling and analytical schemes, the
application of robust models, independent validation of the 210
Pb-derived chronology with
other time markers such as 137
Cs and the use of multi-tracers with different half-lives, e.g. 7Be
and 234
Th, whose short half-lives can provide useful information on sedimentary processes
over the very recent past (3-8 months).
Literature Review
49
References
Abrahim, G.M.S. & Parker, R.J. (2008). Assessment of heavy metal enrichment factors and
the degree of contamination in marine sediments from Tamaki Estuary, Auckland,
New Zealand. Environ Monit Assess. 136, 227-238
Abrajano Jr, T. A., Yan, B., Song, J., Bopp, R., & O'Malley, V. (2007). High-Molecular-
Weight Petrogenic and Pyrogenic Hydrocarbons in Aquatic Environments. In D. H.
Editors-in-Chief: Heinrich & K. T. Karl (Eds.), Treatise on Geochemistry (pp. 1-50).
Oxford: Pergamon.
Abril, J.M. & Brunskill, G.J. (2014). Evidence that excess 210
Pb flux varies with sediment
accumulation rate and implications for dating recent sediments. J. Paleolimnol,
52(3):121-137.
Abril J.M. & Gharbi, F. (2012). Radiometric dating of recent sediments: beyond the boundary
conditions. J. Paleolimnol., 48(2), 449-460.
Abril, J.M. (2004). Constraints on the use of 137
Cs as a time-marker to support CRS and SIT
chronologies. Environ. Pollut. 129(1), 31-37.
Abril, J.M. & Garcia-Le6n, M. (1994). The Integrated Atmospheric Flux Effect in a
Radiogeochronological Model. J. Environ. Radioact. 24, 65-79.
Abril, J.M., Garcia-Le6n, M., Garcia-Tenorio, R., Sinchez, C.I. & EI-Daoushy, F. (1992).
Dating of Marine Sediments by an Incomplete Mixing Model. J. Environ. Radioact.
15, 135-151.
Adams, M.S. & Stauber, J.L. (2008). Marine whole sediment toxicity tests for use in
temperate and tropical Australian environments: current status. Aust. J. Ecotoxicol. 14,
155-167.
Addo, M.A.; Darko, E.O.; Gordon, C.; Nyarko, B.J.B.; Gbadago, J.K.; Nyarko, E.; Affum,
H.A.; Botwe, B.O. (2012). Evaluation of Heavy Metals Contamination of Soil and
Vegetation in the Vicinity of a Cement Factory in the Volta Region, Ghana. Int. J. Sci.
and Technol., 2(1): 40-50.
Addo, M.A.; Okley, G.M.; Affum, H.A.; Acquah, S.; Gbadago, J.K.; Senu, J.K.; Botwe, B.O.
(2011). Water quality and level of some heavy metals in water and sediments of
Kpeshie Lagoon, La-Accra, Ghana. Res. J. Environ. Earth Sci., 3(5): 487-497.
Ahmed, G., Anawar, H.M., Takuwa, D.T., Chibua, I.T., Singh, G.S. & Sichilongo, K. (2015).
Environmental assessment of fate, transport and persistent behavior of
Literature Review
50
dichlorodiphenyltrichloroethanes and hexachlorocyclohexanes in land and water
ecosystems. Int. J. Environ. Sci. Technol. 12, 2741-2756.
Akrasi, S. (2011). Sediment discharges from Ghanaian rivers into the sea. West Afr. J. Appl.
Ecol. 18, 1-13.
Alonso-Hernandez, C. M., Diaz-Asencio, M., Munoz-Caravaca, A., Delfanti, R., Papucci, C.,
Ferretti, O., & Crovato, C. (2006). Recent changes in sedimentation regime in
Cienfuegos Bay, Cuba, as inferred from 210Pb and 137Cs vertical profiles. Conti.
Shelf Res., 26(2), 153-167.
Aloupi, M. & Angelidis, M. (2001). Geochemistry of natural and anthropogenic metals in the
coastal sediments of the island of Lesvos, Aegean Sea. Environ. Pollut. 113, 211-219.
Al-Trabulsy, H., Khater, A., & Habbani, F. (2011). Radioactivity levels and radiological
hazard indices at the Saudi coastline of the Gulf of Aqaba. Radiat. Phys. Chem. 80(3),
343-348.
Alvarez-Vazquez, M.A., Caetano, M., Alvarez-Iglesias, P., del Canto Pedrosa-García, M.,
Calvo, S., De Una-Alvarez, E., Quintana, B., Vale, C. & Prego, R. (2017). Natural
and anthropocene fluxes of trace elements in estuarine sediments of Galician Rias.
Estuar. Coast. Shelf Sci. 198, 329-342.
Annicchiarico, C., Biandolino, F., Cardellicchio, N., Di Leo, A., Giandomenico, S., & Prato,
E., 2007. Predicting toxicity in marine sediment in Taranto Gulf (Ionian Sea, Southern
Italy) using Sediment Quality Guidelines and a battery bioassay. Ecotoxicology, 16,
239-246.
Appleby, P.G. (2008). Three decades of dating recent sediments by fallout radionuclides: A
review. Holocene, 18(1), 83-93.
Appleby, P.G. & Oldfield, F. (1978). The calculation of lead-210 dates assuming a constant
rate of supply of unsupported 210
Pb to the sediment. CATENA, 5(1), 1-8.
Appleby, P.G. (2004). Environmental change and atmospheric contamination on Svalbard:
sediment chronology. J. Paleolimnol., 31(4), 433-444.
Appleby, P.G. & Oldfield, F. (1983). The assessment of 210
Pb data from sites with varying
sediment accumulation rates. Hydrobiologia, 103(1), 29-35.
Appleby, P.G. (2002). Chronostratigraphic Techniques in Recent Sediments. In W. Last & J.
Smol (Eds.), Tracking Environmental Change Using Lake Sediments (Vol. 1, pp. 171-
203): Springer Netherlands.
Appleby, P.G. (1992). Dating recent sediments by 210
Pb: problems and solutions. STUK-
A145.
Literature Review
51
Arnaud, F., Magand, O., Chapron, E., Bertrand, S., Boës, X., Charlet, F., & Mélières, M. A.
(2006). Radionuclide dating (210
Pb, 137
Cs, 241
Am) of recent lake sediments in a highly
active geodynamic setting (Lakes Puyehue and Icalma—Chilean Lake District). Sci.
Total Environ. 366(2-3), 837-850.
Baran, A. & Tarnawski, M. (2013). Phytotoxkit/Phytotestkit and Microtox as tools for toxicity
assessment of sediments. Ecotoxicol. Environ. Safety 98, 19-27.
Barneveld, H. & Hugtenburg, J. (2008). Feasibility study for implementation of sedimentation
reduction measures in river harbours. RCEM, 1187-1192.
Bat, L. & Raffaelli, D. (1998). Sediment toxicity testing: a bioassay approach using the
amphipod Corophium volutator and the polychaete Arenicola marina. J. Exp. Mar.
Bio. Ecol. 226, 217-239.
Beg, K.R. & Ali, S. (2008). Microtox Toxicity Assay for the Sediment Quality Assessment of
Ganga River. American J. Environ. Sci. 4(4), 383-387.
Beiras, R., Bellas, J., Fern ndez, N., Lorenzo, J. I. Cobelo-Garc a, A. (2003). Assessment
of coastal marine pollution in Galicia (NW Iberian Peninsula); metal concentrations in
seawater, sediments and mussels (Mytilus galloprovincialis) versus embryo–larval
bioassays using Paracentrotus lividus and Ciona intestinalis. Mar. Environ. Res.
56(4), 531-553.
Bellucci, L. G., Giuliani, S., Romano, S., Albertazzi, S., Mugnai, C., & Frignani, M. (2012).
An Integrated Approach to the Assessment of Pollutant Delivery Chronologies to
Impacted Areas: Hg in the Augusta Bay (Italy). Environ. Sci. Technol. 46(4), 2040-
2046.
Beresford, N., Brown, J., Copplestone, D., Garnier-Laplace, J., Howard, B., Larsson, C.-M.,
Oughton, D., Prӧhl, G., Zinger, I. (2007). D-ERICA: An integrated approach to the
assessment and management of environmental risk from ionising radiation.
Description of purpose, methodology and application.
Berto, D., Giani, M., Boscolo, R., Covelli, S., Giovanardi, O., Massironi, M., & Grassia, L.
(2007). Organotins (TBT and DBT) in water, sediments, and gastropods of the
southern Venice lagoon (Italy). Mar. Pollut. Bull., 55(10), 425-435.
Birch, G.F., & Hutson, P., 2009. Use of sediment risk and ecological/conservation value for
strategic management of estuarine environments: Sydney estuary, Australia. Environ.
Manage. 44, 836-850.
Birch, G.F., Gunns, T.J. & Olmos, M. (2015). Sediment-bound metals as indicators of
anthropogenic change in estuarine environments. Mar. Pollut. Bull. 101, 243-257.
Literature Review
52
Birch, G.F. & Olmos, M.A. (2008). Sediment-bound heavy metals as indicators of human
influence and biological risk in coastal water bodies. ICES J. Mar. Sci. 65: 1407-1413.
Bloesch, J. & Burns, N. (1980). A critical review of sedimentation trap technique. Schweiz Z
Hydrol., 42(1), 15-55.
Botwe, B.O., Nyarko, E. & Ntow, W.J. (2012). Pesticide Contamination in Groundwater and
Streams Draining Vegetable Plantations in the Ofinso District, Ghana. In: Hernandez-
Soriano, M.C. (Ed.), Soil Health and Land Use Management, InTech, pp. 51-66.
Rijeka, Croatia.
Brisson, L.N., Wolfe, D.A. & Staley, M. (2014). Interferometric swath bathymetry for large
scale shallow water hydrographic surveys. Canadian Hydrographic Conference; 1-18.
Brucker, S., Clarke, J.H., Beaudoin, J., Lessels, C., Czotte, K., Loschiavo, R., Iwanowska, K.
& Hill, P. (2007). Monitoring flood-related change in bathymetry and sediment
distribution over the Squamish Delta, Howe Sound, British Columbia. U.S.
Hydrographic Conference, 1-16.
Buesseler, K.O., Antia, A.N., Chen, M., Fowler, S.W., Gardner, W.D., Gustafsson, O.,
Harada, K., Michaels, A.F., Rutgers van der Loeff, M. & Sarin, M. (2007). An
assessment of the use of sediment traps for estimating upper ocean particle fluxes. J
Mar Res 65(3), 345-416.
Burdige, D.J., 2007. Preservation of organic matter in marine sediments: controls,
mechanisms, and an imbalance in sediment organic carbon budgets? Chem. Rev.
107(2), 467-485.
Burgess, R.M., Perron, M.M., Cantwell, M.G., Ho, K.T., Pelletier, M.C., Serbst, J.R. & Ryba,
S.A. (2007). Marine sediment toxicity identification evaluation methods for the
anionic metals arsenic and chromium. Environ. Toxicol. Chem. 26, 61-67.
Burton, G.A. (2002). Sediment quality criteria in use around the world. Limnology, 3, 65-76.
Calmano, W., Hong, J. & Foerstner, U. (1993). Binding and mobilization of heavy metals in
contaminated sediments affected by pH and redox potential. Water. Sci. Technol., 28,
223-223.
Caroll, J. & Lerche, I. (2003). Sedimentary Processes: Quantification Using Radionuclides.
Elsevier.
Carvalho, S., Cunha, M.R., Pereira, F., Pousão-Ferreira, P., Santos, M., & Gaspar, M. (2012).
The effect of depth and sediment type on the spatial distribution of shallow soft-
bottom amphipods along the southern Portuguese coast. Helgol. Mar. Res. 66, 489-
501.
Literature Review
53
Casado-Martínez MC., Buceta JL, Belzunce MJ, DelValls TA (2006) Using sediment quality
guidelines for dredged material management in commercial ports from Spain. Environ.
Int. 32, 388-396.
Casado-Martinez, M.C., Forja, J.M., & DelValls, T.A., 2007. Direct comparison of amphipod
sensitivities to dredged sediments from Spanish ports. Chemosphere, 68, 677-685.
Castro, Í.B., Arroyo, M.F., Costa, P.G. & Fillmann, G. (2012). Butyltin compounds and
imposex levels in Ecuador. Arch. Environ. Contam. Toxicol. 62(1), 68-77.
Champ, P.M. & Seligman, P.F. (1996). Organotin: Environmental Fate and Effects, Chapman
& Hall, London.
Chapman PM (2007) Determining when contamination is pollution - weight of evidence
determinations for sediments and effluents. Environ Int 33(4), 492–501.
Chapman, P.M. & Anderson, J. (2005). A Decision-Making Framework for Sediment
Contamination. Integr. Environ. Assess. Manage., 1(3): 163-173.
Chatterjee, M., Silva Filho E.V., Sarkar, S.K., Sella, S.M., Bhattacharya, A., Satpathy, K.K.,
Prasad, M.V.R., Chakraborty, S. & Bhattacharya, B.D. (2007) Distribution and
possible source of trace elements in the sediment cores of a tropical macrotidal estuary
and their ecotoxicological significance. Environ. Int. 33, 346-356.
Chen, C.Y., Wang, Y.J. and Yang, Ch. F. (2009). Estimating low toxic effect concentrations
in closed system algal toxicity tests. Ecotoxicol. Environ. Safety, 72, 1514–1522.
Ciarelli, S., Vonck, W., Van Straalen, N., & Stronkhorst, J., 1998. Ecotoxicity assessment of
contaminated dredged material with the marine amphipod Corophium volutator. Arch.
Environ. Contam. Toxicol. 34, 350-356.
Clark, R.B. (2001). Marine Pollution. Oxford: Oxford University Press.
Clifton, R.J., Watson, P.G., Davey, J.T. & Frickers, P.E. (1995). A study of processes
affecting the uptake of contaminants by intertidal sediments, using the radioactive
tracers: 7Be,
137Cs and unsupported
210Pb. Estuar. Coast. Shelf Sci. 41, 459-474.
Connon, R.E., Geist, J. & Werner, I. (2012). Effect-based tools for monitoring and predicting
the ecotoxicological effects of chemicals in the aquatic environment. Sensors, 12,
12741-12771.
Corbett, D.R., Walsh, J.P. & Marciniak, K. (2009). Temporal and spatial variability of trace
metals in sediments of two adjacent tributaries of the Neuse River Estuary, North
Carolina, USA. Mar. Pollut. Bull., 58(11), 1739-1747.
Davidson, C. M., Urquhart, G. J., Ajmone-Marsan, F., Biasioli, M., da Costa Duarte, A., Díaz-
Barrientos, E., . . . Madrid, L. (2006). Fractionation of potentially toxic elements in
Literature Review
54
urban soils from five European cities by means of a harmonised sequential extraction
procedure. Analytica Chimica Acta, 565(1), 63-72.
de-la-Ossa-Carretero, J.A., Del-Pilar-Ruso, Y., Giménez-Casalduero, F., Sánchez-Lizaso, J.L.
& Dauvin, J.-C. (2012). Sensitivity of amphipods to sewage pollution. Estuar. Coastal
Shelf Sci., 96, 129-138
De Luca, G., Furesi, A., Leardi, R., Micera, G., Panzanelli, A., Piu, P.C. & Sanna, G. (2004).
Polycyclic aromatic hydrocarbons assessment in the sediments of the Porto Torres
Harbour (Northern Sardinia, Italy). Mar. Chem. 86(1), 15-32.
DelValls, T., Andres, A., Belzunce, M., Buceta, J., Casado-Martinez, M., Castro, R., Riba, I.,
Viguri, J.R. & Blasco, J. (2004). Chemical and ecotoxicological guidelines for
managing disposal of dredged material. Trends Anal. Chem. 23, 819-828.
Denton, G. R. W., Concepcion, L. P., Wood, H. R. & Morrison, R. J. (2006). Polychlorinated
biphenyls (PCBs) in sediments of four harbours in Guam. Mar. Pollut. Bull. 52(6),
711-718.
de Souza, V.L.B., Rodrigues, K.R.G., Pedroza, E. H., Melo, R.T., Lima, V.L., Hazin, C. A., . .
Nascimento, R.K. (2012). Sedimentation Rate and 210
Pb Sediment Dating at Apipucos
Reservoir, Recife, Brazil. Sustainability, 4(10), 2419-2429.
de Vicente, I., Cruz-Pizarro, L., Rueda, F.J. (2010). Sediment resuspension in two adjacent
shallow coastal lakes: controlling factors and consequences on phosphate dynamics.
Aquat Sci, 72(1):21-31.
de Vleeschouwer, F., Sikorski, J. & Fagel, N. (2010). Development of lead-210 measurement
in peat using polonium extraction. A procedural comparison. Geochronometria, 36(1),
1-8.
Díaz-Asencio, M., Alonso-Hernández, C. M., Bolanos-Álvarez, Y., Gómez-Batista, M., Pinto,
V., Morabito, R., . . . Sanchez-Cabeza, J. A. (2009). One century sedimentary record
of Hg and Pb pollution in the Sagua estuary (Cuba) derived from 210
Pb and 137
Cs
chronology. Mar. Pollut. Bull., 59(4–7), 108-115.
Di Leonardo, R., Bellanca, A., Capotondi, L., Cundy, A., & Neri, R. (2007). Possible impacts
of Hg and PAH contamination on benthic foraminiferal assemblages: An example
from the Sicilian coast, central Mediterranean. Sci. Total Environ. 388(1-3), 168-183.
Di Palma L, Mecozzi R (2007) Heavy metals mobilization from harbour sediments using
EDTA and citric acid as chelating agents. J. Hazard. Mater., 147, 768-775.
Díaz-de Alba, M., Galindo-Riaño, M. D., Casanueva-Marenco, M. J., García-Vargas, M. &
Kosore, C. M. (2011). Assessment of the metal pollution, potential toxicity and
Literature Review
55
speciation of sediment from Algeciras Bay (South of Spain) using chemometric tools.
J. Hazard. Mater. 190(1-3), 177-187.
Dung, T.T.T., Cappuyns, V., Swennen, R. & Phung, N.K. (2013). From geochemical
background determination to pollution assessment of heavy metals in sediments and
soils. Rev Environ Sci Bio/Technol, 12, 335-353.
Eggen, R.I., Behra, R., Burkhardt-Holm, P., Escher, B.I., & Schweigert, N., 2004. Challenges
in ecotoxicology. Environ. Sci. Technol. 38, 58A-64A
El Mamoney, M., & Khater, A.E. (2004). Environmental characterization and radio-ecological
impacts of non-nuclear industries on the Red Sea coast. J. Environ. Radioact. 73(2),
151-168.
Erten, H., Von Gunten, H., Rössler, E. & Sturm, M. (1985). Dating of sediments from Lake
Zurich (Switzerland) with210Pb and 137
Cs. Swiss J Hydrol, 47(1), 5-11.
Erten H. (1997). Radiochronology of lake sediments. Pure Appl Chem, 69(1),71-76.
Erten, H.N. (2011). Radiochronological Methods as Tools to Study Environmental Pollution.
In H. Gökçekus, U. Türker, & J.W. LaMoreaux (Eds.), Survival and Sustainability (pp.
1015-1022): Springer Berlin Heidelberg.
Escher, B.I., Bramaz, N., Mueller, J.F., Quayle, P., Rutishausera, S. & Vermeirssena, E.L.M
(2008). Toxic equivalent concentrations (TEQs) for baseline toxicity and specific
modes of action as a tool to improve interpretation of ecotoxicity testing of
environmental samples. J. Environ. Monit. 10, 612-621.
Forrester, G.E., Fredericks, B.I., Gerdeman, D., Evans, B., Steele, M.A., Zayed, K.,
Schweitzer, L.E., Suffet, I.H., Vance, R.R., & Ambrose, R.F., 2003. Growth of
estuarine fish is associated with the combined concentration of sediment contaminants
and shows no adaptation or acclimation to past conditions. Mar. Environ. Res. 56,
423-442.
Gaillardet, J., Viers, J. & Dupre, B. (2003). Trace elements in river waters. In: Holland, H.D.,
Turekian, K.K. (Eds.), Treatise on Geochemistry, vol. 5. Elsevier, pp. 225-272.
Gaion, A., Sartori, D., Scuderi, A., & Fattorini, D. (2014). Bioaccumulation and
biotransformation of arsenic compounds in Hediste diversicolor (Muller 1776) after
exposure to spiked sediments. Environ. Sci. Pollut. Res. 21, 5952-5959.
Geissen, V., Mol, H., Klumpp, E., Umlauf, G., Nadal, M., van der Ploeg, M., van de Zee,
S.E.A.T.M. & Ritsema, C.J. (2015). Emerging pollutants in the environment: A
challenge for water resource management. Int. Soil Water Conserv. Res. 3, 57-65.
Literature Review
56
George, D., Gelfenbaum, G., & Stevens, A. (2012). Modeling the Hydrodynamic and
Morphologic Response of an Estuary Restoration. Estuaries and Coasts, 35(6), 1510-
1529.
Ghirardini, A.V., Girardini, M., Marchetto, D. & Pantani, C. (2009). Microtox solid phase
test: Effect of diluent used in toxicity test. Ecotoxicol. Environ. Safety, 72, 851-861.
Giffin, D. & Corbett, D.R. (2003). Evaluation of sediment dynamics in coastal systems via
short-lived radioisotopes. J. Mar. Syst., 42(3), 83-96.
Giuliani, S., Piazza, R., Bellucci, L. G., Cu, N. H., Vecchiato, M., Romano, S., . . . Frignani,
M. (2011). PCBs in Central Vietnam coastal lagoons: Levels and trends in dynamic
environments. Mar. Pollut. Bull. 62(5), 1013-1024.
Giuliani, S., Piazza, R., El Moumni, B., Polo, F.P., Vecchiato, M., Romano, S., Zambon, S.,
Frignani, M. & Bellucci, L.G. (2015). Recognizing different impacts of human and
natural sources on the spatial distribution and temporal trends of PAHs and PCBs
(including PCB-11) in sediments of the Nador Lagoon (Morocco). Sci. Total Environ.
526, 346-357.
Giuliani, S., Sprovieri, M., Frignani, M., Cu, N.H., Mugnai, C., Bellucci, L.G., Albertazzi, S.,
Romano, S., Feo, M.L., Marsella, E. and Nhon, D.H. (2008). Presence and origin of
polycyclic aromatic hydrocarbon in sediments of nine coastal lagoons in central
Vietnam. Mar. Pollut. Bull. 56, 1486-1512.
Giuliani, S., Piazza, R., Bellucci, L. G., Cu, N. H., Vecchiato, M., Romano, S., . . . Frignani,
M. (2011). PCBs in Central Vietnam coastal lagoons: Levels and trends in dynamic
environments. Mar. Pollut. Bull., 62(5), 1013-1024.
Gómez-Gutiérrez, A., Garnacho, E., Bayona, J. M. & Albaigés, J. (2007). Screening
ecological risk assessment of persistent organic pollutants in Mediterranean sea
sediments. Environ. Int. 33(7), 867-876.
Green, M.O. & Coco, G. (2014). Review of wave‐driven sediment resuspension and transport
in estuaries. Rev. Geophys. 52(1), 77-117.
Guerra, R., Dinelli, E., Righi, S., Forja, J.M. & García-Luque, E. (2010). Sediment
geochemistry and accumulation rates on the northeastern shelf of the Gulf of Cádiz
(SW Iberian Peninsula). Adv. Mar. Chem, DOI: 10.3989/scimar.2010.74s1067.
Guerra, R. (2012). Polycyclic Aromatic Hydrocarbons, Polychlorinated Biphenyls and Trace
Metals in Sediments from a Coastal Lagoon (Northern Adriatic, Italy). Water, Air, Soil
Pollut. 223(1), 85-98.
Literature Review
57
Gunten, L., Grosjean, M., Beer, J., Grob, P., Morales, A. & Urrutia, R. (2009). Age modeling
of young non-varved lake sediments: methods and limits. Examples from two lakes in
Central Chile. J. Paleolimnol., 42(3), 401-412.
Gupta, A.K., Gupta, S.K. & Rashmi, S.P. (2005). Environmental management plan for port
and harbour projects. Clean Techn Environ Policy. 7, 133–141.
Hakanson, L. (2006). Suspended Particulate Matter in lakes, rivers, and marine systems.
Blackburn Press, Caldwell.
Hakanson, L., & Jansson, M. (1983) Principles of lake sedimentology. Springer Verlag,
Berlin.
Hamed, M.A., Mohamedein, L. I., El-Sawy, M.A., & El-Moselhy, K.M. (2013). Mercury and
tin contents in water and sediments along the Mediterranean shoreline of Egypt. The
Egypt. J. Aquat. Res., 39(2), 75-81.
Hamzeh, M., Ouddane, B., Daye, M., Halwani, J. (2014). Trace Metal Mobilization from
Surficial Sediments of the Seine River Estuary. Water Air Soil Pollut. 225, 1878-1892.
Hanna, S.K., Miller, R.J., Zhoud, D., Keller, A.A. & Lenihan, H.S. (2013). Accumulation and
toxicity of metal oxide nanoparticles in a soft-sediment estuarine amphipod. Aquatic
Toxicology, 142-143, 441- 446
Hannewijk, A., Kater, B.J. & Schipper, C.A. (2004). Sediment toxiciteitstest met Nereis
diversicolor (In Dutch). 22 pp.
Hassona, R.K., Sam, A.K., Osman, O.I., Sirelkhatim, D.A. & LaRosa, J. (2008). Assessment
of committed effective dose due to consumption of Red Sea coral reef fishes collected
from the local market (Sudan). Sci. Total Environ. 393(2-3), 214-218.
Helali, M.A., Zaaboub, N., Oueslati, W., Added, A. & Aleya, L. (2016). Suspended
particulate matter fluxes along with their associated metals, organic matter and
carbonates in a coastal Mediterranean area affected by mining activities. Mar. Pollut.
Bull., 104(1), 171-181.
Hernandez, J-M.A. (2015). Why would we use the Sediment Isotope Tomography (SIT)
model to establish a 210
Pb-based chronology in recent-sediment cores? J. Environ.
Radioact., 143, 40-46.
Hollins, S., Harrison, J., Jones, B., Zawadzki, A., Heijnis, H. & Hankin, S. (2011).
Reconstructing recent sedimentation in two urbanised coastal lagoons (NSW,
Australia) using radioisotopes and geochemistry. J. Paleolimnol., 46(4), 579-596.
Horowitz, A.J. & Elrick, K.A. (1987). The relation of stream sediment surface area, grain size
and composition to trace element chemistry. Applied Geochem. 2(4), 437-451.
Literature Review
58
Horowitz, A. J., 1985. A primer on trace metal-sediment chemistry, U.S. Geological Survey
Water-Supply Paper 2277, 67 p.
Hu, W., Wang, T., Khim, J.S., Luo, W., Jiao, W., Lu, Y., Naile, J.E., Chen, C., Zhang, X. &
Giesy, J.P. (2009). HCH and DDT in Sediments from Marine and Adjacent Riverine
Areas of North Bohai Sea, China. Arch. Environ. Contam. Toxicol. DOI
10.1007/s00244-009-9455-z.
ICES, 2008. Report of the Fourth ICES/OSPAR Workshop on Integrated Monitoring of
Contaminants and their Effects in Coastal and Open Sea Areas (WKIMON IV). ICES
Document CM 2008/ACOM: 49. 71 pp.
Iqbal, J., Tirmizi, S. & Shah, M. (2013). Statistical apportionment and risk assessment of
selected metals in sediments from Rawal Lake (Pakistan). Environ. Monit. Assess.
185(1), 729-743.
Islam, M.S. & Tanaka, M. (2004). Impacts of pollution on coastal and marine ecosystems
including coastal and marine fisheries and approach for management: a review and
synthesis. Mar. Pollut. Bull. 48(7-8), 624-649.
Jain, C. (2004). Metal fractionation study on bed sediments of River Yamuna, India. Water
Res., 38, 569-578.
James, I. D. (2002). Modelling pollution dispersion, the ecosystem and water quality in
coastal waters: a review. Environ. Model. Software, 17(4), 363-385.
James, I. D. (2002). Modelling pollution dispersion, the ecosystem and water quality in
coastal waters: a review. Environ. Model. Software, 17(4), 363-385.
Jiang, J., Wang, J., Liu, S., Lin, C, He, M. & Liu, X. (2013). Background, baseline,
normalization, and contamination of heavy metals in the Liao River Watershed
sediments of China. J. Asian Earth Sci. 73, 87-94.
Kalman, J., Riba, I., DelValls, A. and Blasco, J. (2012). Bioaccumulation and effects of
metals bound to sediments collected from Gulf of Cádiz (SW Spain) using the
polychaete Arenicola marina. Arch. Environ. Contam. Toxicol., 62, 22–28.
Kalwa, M., Quináia, S., Pletsch, A., Techy, L., & Felsner, M. (2013). Fractionation and
Potential Toxic Risk of Metals From Superficial Sediment in Itaipu Lake—Boundary
Between Brazil and Paraguay. Arch. Environ. Contam. Toxicol. 64(1), 12-22.
Kannan, K., Johnson-Restrepo, B., Yohn, S. S., Giesy, J. P., & Long, D. T. (2005). Spatial
and Temporal Distribution of Polycyclic Aromatic Hydrocarbons in Sediments from
Michigan Inland Lakes. Environ. Sci. Technol., 39(13), 4700-4706.
Literature Review
59
Kelderman, P. (2012). Sediment Pollution, Transport, and Abatement Measures in the City
Canals of Delft, The Netherlands. Water Air Soil Pollut. 223(7), 4627-4645.
Kelderman, P. & Osman, A.A. (2007). Effect of redox potential on heavy metal binding forms
in polluted canal sediments in Delft (The Netherlands). Water Res. 41(18), 4251-4261.
Kelderman P, Ang‘weya R, De Rozari P, Vijverberg T. (2012). Sediment characteristics and
wind-induced sediment dynamics in shallow Lake Markermeer, the Netherlands.
Aquat Sci, 74(2), 301-313.
Khaba, L. & Griffiths, J.A. (2017). Calculation of reservoir capacity loss due to sediment
deposition in the Muela reservoir, Northern Lesotho. Int Soil Water Conserv Res, 5,
130-140.
King, A., Readman, J. & Zhou, J., 2004. Dynamic behaviour of polycyclic aromatic
hydrocarbons in Brighton marina, UK. Mar. Pollut. Bull. 48(3), 229-239.
Koide, M., Bruland, K.W., & Goldberg, E.D. (1973). Th-228/Th-232 and Pb-210
geochronologies in marine and lake sediments. Geochimica et Cosmochimica Acta,
37(5), 1171-1187.
Kurnaz, A., Küçükömeroğlu, B., Keser, R., Okumusoglu, N., Korkmaz, F., Karahan, G.,
Çevik, U. (2007). Determination of radioactivity levels and hazards of soil and
sediment samples in F rt na Valley (Rize, Turkey). Appl. Radiat.Isot., 65(11), 1281-
1289.
Kusimi, J.M. & Dika, J.L. (2012). Sea erosion at Ada Foah: assessment of impacts and
proposed mitigation measures. Nat Hazards, 64, 983-997.
Larsson, C.-M. (2008). An overview of the ERICA Integrated Approach to the assessment and
management of environmental risks from ionising contaminants. J. Environ.
Radioact., 99(9), 1364-1370.
Lepland, A., Andersen, T.J., Lepland, A., Arp, H.P.H., Alve, E., Breedveld, G.D., & Rindby,
A., 2010. Sedimentation and chronology of heavy metal pollution in Oslo harbour,
Norway. Mar. Pollut. Bull. 60, 1512-1522.
Leys, V., & Mulligan, R.P. (2011). Modelling coastal sediment transport for harbour
planning: selected case studies. INTECH.
Libralato, G., Losso, C., Novelli, A.A., Citron, M., Sala, S.D., Zanotto, E., Cepak, F. &
Ghirardini, A.V. (2008). Ecotoxicological evaluation of industrial port of Venice
(Italy) sediment samples after a decontamination treatment. Environ. Pollut. 156, 644-
650.
Literature Review
60
Lin, T., Hu, Z., Zhang, G., Li, X., Xu, W., Tang, J. & Li, J. (2009). Levels and mass burden of
DDTs in sediments from fishing harbours: the importance of DDT-containing
antifouling paint to the coastal environment of China. Environ. Sci. Technol. 43(21),
8033-8038.
Little, M. (2003). Risks associated with ionizing radiation Environmental pollution and health.
Brit. Med. Bull. 68(1), 259-275.
Liu, J., Clift, P.D., Yan, W., Chen, Z., Chen, H., Xiang, R., & Wang, D. (2014). Modern
transport and deposition of settling particles in the northern South China Sea:
Sediment trap evidence adjacent to Xisha Trough. Deep Sea Research Part I:
Oceanographic Research Papers, 93, 145-155.
Livingston, H.D. & Povinec, P.P. (2000). Anthropogenic marine radioactivity. Ocean &
Coastal Manage. 43(8), 689-712.
Long, E.R., Ingersoll, C.G. & MacDonald, D.D. (2006). Calculation and uses of mean
sediment quality guideline quotients: a critical review. Environ. Sci. Technol. 40(6),
1726-1736.
Long, E.R., Field, L.J., & MacDonald, D.D. (1998). Predicting toxicity in marine sediments
with numerical sediment quality guidelines. Environ. Toxicol. Chem., 17(4), 714-727.
Long, E.R., MacDonald, D.D., Smith, S. L., & Calder, F.D. (1995). Incidence of adverse
biological effects within ranges of chemical concentrations in marine and estuarine
sediments. Environ. Manage., 19(1), 81-97.
Lu, X. (2007). A note on removal of the compaction effect for the 210
Pb method. Appl. Radiat.
Isot, 65(1), 142-146.
Luo, X., Mai, B., Yang, Q., Fu, J., Sheng, G. & Wang, Z. (2004). Polycyclic aromatic
hydrocarbons (PAHs) and organochlorine pesticides in water columns from the Pearl
River and the Macao harbor in the Pearl River Delta in South China. Mar. Pollut. Bull.
48, 1102–1115.
Luo, W., Lu, Y., Wang, T., Hu, W., Jiao, W., Naile, J.E., Khim, J.S. & Giesy, J.P. (2010).
Ecological risk assessment of arsenic and metals in sediments of coastal areas of
northern Bohai and Yellow Seas, China. Ambio, 39(5-6), 367-375.
Mabit, L., Benmansour, M. & Walling, D.E. (2008). Comparative advantages and limitations
of the fallout radionuclides 137
Cs, 210
Pbex and 7Be for assessing soil erosion and
sedimentation. J. Environ. Radioact. 99, 1799-1807.
Mabit, L., Benmansour, M., Abril, J., Walling, D., Meusburger, K., Iurian, A.R., Bernard, C.,
Tarján, S., Owens, P.N., Blake, W.H., & Alewell, C. (2014). Fallout 210
Pb as a soil and
Literature Review
61
sediment tracer in catchment sediment budget investigations: a review. Earth-Sci.
Rev., 138, 335-351.
MacKenzie, A.B., Hardie, S.M.L., Farmer, J.G., Eades, L.J. & Pulford, I.D. (2011). Analytical
and sampling constraints in 210
Pb dating. Sci. Total Environ., 409, 1298-1304.
Mahapatra, D.M., Chanakya H.N. & Ramachandra, T.V. (2011). C:N ratio of Sediments in a
sewage fed Urban Lake. Int. J. Geol., 5(3), 86-92.
Mahu, E, Nyarko, E., Hulme, S. & Coale, K.H. (2015). Distribution and enrichment of trace
metals in marine sediments from the Eastern Equatorial Atlantic, off the Coast of
Ghana in the Gulf of Guinea. Mar. Pollut. Bull., 98, 301-307.
Magi, E. & Di Carro, M. (2016). Marine environment pollution: The contribution of mass
spectrometry to the study of seawater. Mass Spectrom. Rev. doi: 10.1002/mas.21521.
Mai, B., Qi, S., Zeng, E.Y., Yang, Q., Zhang, G., Fu, J., Sheng, G., Peng, P. & Wang, Z.
(2003). Distribution of polycyclic aromatic hydrocarbons in the coastal region off
Macao, China: assessment of input sources and transport pathways using
compositional analysis. Environ. Sci. Technol., 37, 4855-4863.
Mamindy-Pajany, Y., Bataillard, P., Séby, F., Crouzet, C., Moulin, A., Guezennec, A.-G.,
Hrel, C., Marmier, N., & Battaglia-Brunet, F. (2013). Arsenic in Marina Sediments
from the Mediterranean Coast: Speciation in the Solid Phase and Occurrence of
Thioarsenates. Soil and Sediment Contam: An Int. J., 22(8), 984-1002.
Mariño-Balsa, J.C., Pérez, P., Estévez-Blanco, P., Saco-Álvarez, L., Fernández, E. and Beiras,
R. (2003). Assessment of the toxicity of sediment and seawater polluted by the
Prestige fuel spill using bioassays with clams (Venerupis pollastra, Tappes decussates
and Venerupis rhomboideus) and the microalga Skeletonema costatum. Ciencias
Marinas 29, 115–122.
Marques Jr, A. N., Monna, F., da Silva Filho, E. V., Fernex, F. E., & Fernando Lamego
Simões Filho, F. (2006). Apparent discrepancy in contamination history of a sub-
tropical estuary evaluated through 210Pb profile and chronostratigraphical markers.
Mar. Pollut. Bull., 52(5), 532-539.
Marsden, I., & Rainbow, P., 2004. Does the accumulation of trace metals in crustaceans affect
their ecology - the amphipod example? J. Exp. Mar. Bio. Ecol. 300, 373-408.
Mayor, D.J., Solan, M., Martinez, I., Murray, L., McMillan, H., Paton, G.I., & Killham, K.,
(2008). Acute toxicity of some treatments commonly used by the salmonid
aquaculture industry to Corophium volutator and Hediste diversicolor: Whole
sediment bioassay tests. Aquaculture, 285, 102-108.
Literature Review
62
McDonald, C. P., & Urban, N. R. (2007). Sediment radioisotope dating across a stratigraphic
discontinuity in a mining-impacted lake. J. Environ. Radioact., 92(2), 80-95.
Mensink, B.P., Everaarts, J.M., Kralt, H., ten Hallers-Tjabbes, C.C. & Boon, J.P. (1996a).
Tributyltin exposure in early life stages induces the development of male sexual
characteristics in the common whelk, Buccinum undatum. Mar. Environ. Res. 42, 151–
154.
Mensink, B.P., ten Hallers-Tjabbes, C.C., Kralt, J., Freriks, I.L. & Boon, J.B. (1996b).
Assessment of imposex in the common whelk, Buccinum undatum (L.) from the
Eastern Scheldt, the Netherlands. Mar. Environ. Res. 41, 315-325.
Mestres M, Sierra J, Mösso C. & Sánchez-Arcilla, A (2010). Sources of contamination and
modelled pollutant trajectories in a Mediterranean harbour (Tarragona, Spain). Mar.
Pollut. Bull. 60, 898-907.
Meybeck, M., Vörösmarty, C., 2005. Fluvial filtering of land-to-ocean fluxes: from natural
Holocene variations to Anthropocene. Comptes Rendus Geosci. 337, 107-123.
Morales-Caselles, C., Riba, I. & DelValls, T.A (2009). A weight of evidence approach for
quality assessment of sediments impacted by an oil spill: The role of a set of
biomarkers as a line of evidence. Mar. Environ. Res. 67, 31-37.
Morales-Caselles, C., Riba, I., Sarasquete, C. & DelValls, T.A. (2008). The application of a
weight of evidence approach to compare the quality of coastal sediments affected by
acute (Prestige 2002) and chronic (Bay of Algeciras) oil spills. Environ. Pollut. 156,
394-402.
Morales-Caselles, C., Kalman, J., Riba, I. & DelValls, T.A. (2007). Comparing sediment
quality in Spanish littoral areas affected by acute (Prestige, 2002) and chronic (Bay of
Algeciras) oil spills. Environ. Pollut., 146, 233-240.
Moreira, S.M., Lima, I., Ribeiro, R., & Guilhermino, L. (2006). Effects of estuarine sediment
contamination on feeding and on key physiological functions of the polychaete
Hediste diversicolor: laboratory and in situ assays. Aquatic Toxicol. 78, 186-201.
Moukhchan, F., March, J. G., & Cerdá, V. (2013). Distribution of trace metals in marine
sediments of the Bay of Palma de Mallorca (Mallorca Island, Spain). Environ. Monit.
Assess. 185(1), 695-706.
Muller, G., 1969. Index of geo-accumulation in sediments of the Rhine River. J. Geol., 2(3):
108-118.
Mulligan, C.N., Yong, R.N. & Gibbs, B.F. (2001). An evaluation of technologies for the
heavy metal remediation of dredged sediments. J. Hazard. Mater. 85, 145-163.
Literature Review
63
Neff, J.M., Stout, S.A. & Gunster, D.G. (2005). Ecological risk assessment of polycyclic
aromatic hydrocarbons in sediments: identifying sources and ecological hazard. Integr.
Environ. Assess. Manage. 1(1), 22-33.
Nehyba, S., Nývlt, D., Schkade, U., Kirchner, G. Franců, E. (2011). Depositional rates and
dating techniques of modern deposits in the Brno reservoir (Czech Republic) during
the last 70 years. J. Paleolimnol., 45(1), 41-55.
Nisbet, I.C. & LaGoy, P.K., 1992. Toxic equivalency factors (TEFs) for polycyclic aromatic
hydrocarbons (PAHs). Regul. Toxicol. Pharm. 16(3), 290-300.
Ntow, W.J. & Botwe, B.O. (2011). Contamination status of organochlorine pesticides in
Ghana. In: Loganathan, B.G. & Lam, P.K.S. (Eds), Global Contamination Trends of
Persistent Organic Chemicals. pp. 393-411. CRC Press, USA.
Nyarko, E., Botwe, B.O., Lamptey, E., Nuotuo, O., Foli, B.A., Addo, M.A. (2011a). Toxic
metal concentrations in deep-sea sediments from the jubilee oil field and surrounding
areas off the western coast of Ghana. Trop. Environ. Res. 9, 584-595.
Nyarko, E., Botwe, B., Ansong, J., Delfanti, R., Barsanti, M., Schirone, A. & Delbono, I.
(2011b). Determination of 210
Pb, 226
Ra and 137
Cs in beach sands along the coastline of
Ghana. Afr. J. Environ. Pollut. Health, 9, 17-23.
Nyarko, E., Botwe, B.O. & Klubi, E. (2011c). Polycyclic aromatic hydrocarbons (PAHs)
levels in two commercially important fish species from coastal waters of Ghana and
their carcinogenic health risks. West Afr. J. Appl. Ecol., 19, 53-66.
Nyarko, E., Fletcher, A., Addo, S., Foli, B.A.K., Mahu, E. (2014). Geochemical Assessment
of Heavy Metals in Surface Sediments: A Case Study of the Tema Port, Ghana. J.
Ship. Ocean Eng. 4, 79-92.
Oehlmann, J. (2002). Baseline study on intersex in Littorina littorea with recommendations
for biological TBT assessment criteria. Report, Johann Wolfgang Goethe University,
Frankfurt am Main. SIME 02/6/1-E.
Oehlmann, J. (2002). Baseline study on intersex in Littorina littorea with recommendations
for biological TBT assessment criteria. Report, Johann Wolfgang Goethe University,
Frankfurt am Main. SIME 02/6/1-E.
Oldfield, F. & Appleby, P.G. (1984). A combined radiometric and mineral magnetic approach
to recent geochronology in lakes affected by catchment disturbance and sediment
redistribution. Chem. Geol., 44(1-3), 67-83.
Literature Review
64
Ortt, R.A., Kerhin, R.T., Wells, D. & Cornwell, J. (2000). Bathymetric survey and
sedimentation analysis of Loch Raven and Prettyboy reservoirs. Coastal and Estuarine
Geology File Report; 99-4.
Pagano, G., Guida, M., Trifuoggi, M., Thomas, P., Palumbo, A., Romano, G. and Oral, R.
(2017a). Sea Urchin Bioassays in Toxicity Testing: I. Inorganics, Organics, Complex
Mixtures and Natural Products. Expert Opin Environ Biol., 6:1. doi: 10.4172/2325-
9655.1000142
Pagano, G., Thomas, P., Guida, M., Palumbo, A., Romano, G., Oral, R. Trifuoggi, M.
(2017b). Sea Urchin Bioassays in Toxicity Testing: II. Sediment Eval. Expert Opin.
Environ Biol., 6, 1.
Palinkas, C., Nittrouer, C., Wheatcroft, R., Langone, L. (2005). The use of 7Be to identify
event and seasonal sedimentation near the Po River delta, Adriatic Sea. Mar. Geol.
222, 95-112.
Petrosillo, I., Valente, D., Zaccarelli, N. & Zurlini, G. (2009). Managing tourist harbors: Are
managers aware of the real environmental risks? Mar. Pollut. Bull. 58, 1454-1461.
Pfitzner, J., Brunskill, G. & Zagorskis, I. (2004). 137
Cs and excess 210
Pb deposition patterns in
estuarine and marine sediment in the central region of the Great Barrier Reef Lagoon,
north-eastern Australia. J. Environ. Radioact. 76(1), 81-102.
Philippe, S., Leterme, C., Lesourd, S., Courcot, L., Haack, U. & Caillaud, J. (2008).
Bioavailability of sediment-borne lead for ragworms (Hediste diversicolor)
investigated by lead isotopes. Appl. Geochem. 23, 2932-2944.
Pini J, Richir J, Watson G (2015) Metal bioavailability and bioaccumulation in the polychaete
Nereis (Alitta) virens (Sars): The effects of site-specific sediment characteristics. Mar.
Pollut. Bull., 95, 565-575.
Power, E.A. & Chapman, P.M. (1992). Assessing sediment quality. In: G.A. Burton Jr. (Ed.),
Sediment toxicity assessment. Lewis Publishers Inc, Boca raton, FL, 457pp.
Prato, E., Parlapiano, I. & Biandolino, F. (2011). Evaluation of a bioassays battery for
ecotoxicological screening of marine sediments from Ionian Sea (Mediterranea Sea,
Southern Italy). Environ Monit Assess, DOI 10.1007/s10661-011-2335-9.
Prato, E., Parlapiano, I. & Biandolino, F. (2015): Ecotoxicological evaluation of sediments by
battery bioassays: application and comparison of two integrated classification systems,
Chemistry and Ecology, DOI:10.1080/02757540.2015.1069278.
Literature Review
65
Ptistišek, N., Milačič, R., Veber, M. (2001). Use of the BCR three-step sequential
extraction procedure for the study of the partitioning of Cd, Pb and Zn in various soil
samples. J. Soils Sediments, 1(1), 25-29.
Pueyo M, Rauret G, Lück D, Yli-Halla M, Muntau H, Quevauviller P, Lopez-Sanchez J
(2001) Certification of the extractable contents of Cd, Cr, Cu, Ni, Pb and Zn in a
freshwater sediment following a collaboratively tested and optimised three-step
sequential extraction procedure. J. Environ. Monit., 3, 243-250.
Qu, W. & Kelderman, P. (2001) Heavy metal contents in the Delft canal sediments and
suspended solids of the River Rhine: multivariate analysis for source tracing.
Chemosphere, 45, 919-925.
Quensen III, J.F., Mueller, S.A., Jain, M.K. & Tiedje, J.M. (1998). Reductive Dechlorination
of DDE to DDMU in Marine Sediment Microcosms. Science, 280 (5364), 722-724.
Quevauviller, P., Rauret, G., López-Sánchez, J. F., Rubio, R., Ure, A., & Muntau, H. (1997).
Certification of trace metal extractable contents in a sediment reference material
(CRM 601) following a three-step sequential extraction procedure. Sci. Total Environ.,
205(2–3), 223-234.
Quevauviller, P., Rauret, G., Muntau, H., Ure, A. M., Rubio, R., López-Sánchez, J. F., . . .
Griepink, B. (1994). Evaluation of a sequential extraction procedure for the
determination of extractable trace metal contents in sediments. Fresenius' J. Anal.
Chem., 349(12), 808-814.
Rae, J.E. (1997). Trace metals in deposited intertidal sediments. In: Jickells, T.D., Rae, J.E.
(Eds.), Biogeochemistry of Intertidal Sediments, Cambridge Environmental Chemistry
Series No. 9. Cambridge University Press, pp. 16-41.
Rainbow, P.S. (2007). Trace metal bioaccumulation: Models, metabolic availability and
toxicity. Environ. Int., 33, 576-582.
Rainbow, P.S. & Luoma, S.N. (2011). Metal toxicity, uptake and bioaccumulation in aquatic
invertebrates – Modelling zinc in crustaceans. Aquatic Toxicol. 105, 455-465
Rajendran, R. B., Imagawa, T., Tao, H., & Ramesh, R. (2005). Distribution of PCBs, HCHs
and DDTs, and their ecotoxicological implications in Bay of Bengal, India. Environ.
Int., 31(4), 503-512.
Rani, M., Shanker, U. & Jassal, V. (2017). Recent strategies for removal and degradation of
persistent & toxic organochlorine pesticides using nanoparticles: A review. J. Environ.
Manage. 190, 208-222.
Literature Review
66
Ravanat, J., Breton, J., Douki, T., Gasparutto, D., Grand, A., Rachidi, W., & Sauvaigo, S.
(2014). Radiation-mediated formation of complex damage to DNA: a chemical aspect
overview. Brit. J. Radiol. 87(1035), 20130715.
Rauret, G., Lopez-Sanchez, J.F., Sahuquillo, A., Rubio, R., Davidson, C., Ure, A. &
Quevauviller, P. (1999). Improvement of the BCR three step sequential extraction
procedure prior to the certification of new sediment and soil reference materials. J.
Environ. Monit., 1, 57-61.
Ré, A., Freitas, R., Sampaio, L., Rodrigues, A.M., & Quintino, V. (2009). Estuarine sediment
acute toxicity testing with the European amphipod Corophium multisetosum Stock,
1952. Chemosphere, 76, 1323-1333.
Robbins, J.A. (1978). Geochemical and geophysical applications of radioactive lead isotopes.
In: Nriagu JO (Ed.), Biogeochemistry of Lead. Elsevier.
Rocher, V., Azimi, S., Moilleron, R., & Chebbo, G. (2004). Hydrocarbons and heavy metals
in the different sewer deposits in the ‗Le Marais‘ catchment (Paris, France): stocks,
distributions and origins. Sci. Total Environ., 323(1-3), 107-122.
Roddie, B., & Thain, J. (2002). Biological effects of contaminants: Corophium sp. sediment
bioassay and toxicity test: International Council for the Exploration of the Sea. ICES
Techniques in Marine Environmental Sciences No. 28, ISSN 0903-2606, Copenhagen,
.Denmark.
Rose, A., Carruthers, A-M, Stauber, J., Lima, R & Blockwell, S. (2006). Development of an
acute toxicity test with the marine copepod Acartia Sinjiensis. Australasian J.
Ecotoxicol, 12, 73-81.
Ruiz-Fernández, A.C., Frignani, M., Hillaire-Marcel, C., Ghaleb, B., Arvizu, M.D., Raygoza-
Viera, J.R. & Páez-Osuna, F. (2009). Trace metals (Cd, Cu, Hg, and Pb) accumulation
recorded in the intertidal mudflat sediments of three coastal lagoons in the Gulf of
California, Mexico. Estuar. Coasts. DOI 10.1007/s12237-009-9150-3.
Ryding, S.-O. (1985). Chemical and Microbiological Processes as Regulators of the Exchange
of Substances between Sediments and Water in Shallow Eutrophic Lakes.
Internationale Revue der gesamten Hydrobiologie und Hydrographie, 70(5), 657-702.
Santos-Echeandía, J., Prego, R., Cobelo-García, A., & Caetano, M. (2012). Metal composition
and fluxes of sinking particles and post-depositional transformation in a ria coastal
system (NW Iberian Peninsula). Mar. Chem., 134, 36-46.
Literature Review
67
Santschi, P.H., Murray, J.W., Baskaran, M., Benitez-Nelson, C.R., Guo, L.D., Hung, C.C.,
Lamborg, C., Moran, S.B., Passow, U. & Roy-Barman, M. (2006). Thorium speciation
in seawater. Mar. Chem. 100(3-4), 250-268.
Santschi, P.H., Presley, B.J., Wade, T.L., Garcia-Romero, B., & Baskaran, M. (2001).
Historical contamination of PAHs, PCBs, DDTs, and heavy metals in Mississippi
River Delta, Galveston Bay and Tampa Bay sediment cores. Mar. Environ. Res. 52(1),
51-79.
Sauvé, S. & Desrosiers, M. (2014). A review of what is an emerging contaminant. Chem
Centr J. 8, 15.
Scaps, P. (2002). A review of the biology, ecology and potential use of the common ragworm
Hediste diversicolor (OF Müller)(Annelida: Polychaeta). Hydrobiologia, 470, 203-
218.
Scarlett, A., Rowland, S., Canty, M., Smith, E., & Galloway, T. (2007). Method for assessing
the chronic toxicity of marine and estuarine sediment-associated contaminants using
the amphipod Corophium volutator. Mar. Environ. Res. 63, 457-470.
Schettler, G., Mingram, J., Negendank, J.F.W., Jiaqi, L. (2006a). Paleovariations in the East-
Asian Monsson regime geochemically recorded in varved sediments of Lake
Sihailongwan (Northeast China, Jilin province). Part 2: a 200-year record of
atmospheric lead-210 flux variations and its palaeoclimatic implications. J.
Paeolimnol. 35, 271-288.
Schettler, G., Qiang, L., Mingram, J., Negendank, J.F.W. (2006b). Paleovariations in the East-
Asian Monsson regime geochemically recorded in varved sediments of Lake
Sihailongwan (Northeast China, Jilin province). Part 1:Hydrological conditions and
flux. J. Paleolimnol. 35, 239-270.
Schipper, C., Rietjens, I., Burgess, R., Murk, A. (2010). Application of bioassays in
toxicological hazard, risk and impact assessments of dredged sediments. Mar. Pollut.
Bull. 60(11), 2026-2042.
Schipper, C.A., Smit, M.G.D., Kaag, N.H.B.M. & Vethaak, A.D. (2008). A weight-of-
evidence approach to assessing the ecological impact of organotin pollution in Dutch
marine and brackish waters; combining risk prognosis and fi eld monitoring using
common periwinkles (Littorina littorea). Mar. Environ. Res. 66, 23-239.
Schipper, C.A., Burgess, R.M., van den Dikkenberg, L.C. (2006). Sediment toxiciteittest met
de slijkgarnaal Corophium volutator (In Dutch). 18 pp.
Literature Review
68
Schmid, E., & Schrader, T. (2007). Different biological effectiveness of ionising and non-
ionising radiations in mammalian cells. Adv. Radio Sci., 5(1), 1-4.
Schmidt S, Jouanneau J-M, Weber O, Lecroart P, Radakovitch O, Gilbert F, Jézéquel D.
(2007a). Sedimentary processes in the Thau Lagoon (France): from seasonal to
century time scales. Estuar Coast Shelf Sci., 72(3), 534-542.
Schmidt S, Gonzalez J-L, Lecroart P, Tronczyński J, Billy I, Jouanneau J-M. (2007b).
Bioturbation at the water-sediment interface of the Thau Lagoon: impact of shellfish
farming. Aquat Living Resour., 20(2), 163-169.
Sikorski, J. Bluszcz, A. (2008). Application of α and γ spectrometry in the 210
Pb method to
model sedimentation in artificial retention reservoir. Geochronometria, 31, pp. 65).
Simpson, C.D., Mosi, A.A., Cullen, W.R. & Reimer, K.J., 1996. Composition and distribution
of polycyclic aromatic hydrocarbon contamination in surficial marine sediments from
Kitimat Harbour, Canada. Sci. Total Environ. 181(3), 265-278.
Simboura, N. & Zenetos, A. (2002). Benthic indicators to use in Ecological Quality
classification of Mediterranean soft bottom marine ecosystems, including a new Biotic
Index. Mediter. Mar. Sci. 3(2), 77-111.
Sinex, S.A. & Helz, G.R. (1981). Regional Geochemistry of Trace Elements in Chesapeake
Bay Sediments. Environ. Geol. 3, 315-323.
Singh, A., & Lal, R. (2009). Sphingobium ummariense sp. nov., a hexachlorocyclohexane
(HCH)-degrading bacterium, isolated from HCH-contaminated soil. Int. J. Syst. Evol.
Microbiol. 59(1), 162-166.
Sirelkhatim, D., Sam, A., & Hassona, R. (2008). Distribution of 226
Ra–210
Pb–210
Po in marine
biota and surface sediments of the Red Sea, Sudan. J. Environ. Radioact. 99(12),
1825-1828.
Smith, J., Lee, K., Gobeil, C. & Macdonald, R. (2009). Natural rates of sediment containment
of PAH, PCB and metal inventories in Sydney Harbour, Nova Scotia. Sci. Total
Environ. 407(17), 4858-4869.
Smith, J. (2001). Why should we believe 210
Pb sediment geochronologies? J. Environ.
Radioact., 55(2), 121-123.
Souza, A. J. & Lane, A. (2013). Effects of freshwater inflow on sediment transport. J.
Operational Oceanography, 6(1), 27-31.
Srivastava, A. and Shivanandappa, T. (2010). Stereospecificity in the cytotoxic action of
hexachlorocyclohexane isomers. Chemico-Biological Interactions, 183 (1): 34-39.
Literature Review
69
Stoschek, O. & Zimmermann, C. (2006). Water Exchange and Sedimentation in an Estuarine
Tidal Harbor Using Three-Dimensional Simulation. J. Waterway Port Coast. Ocean
Engin. 132(5), 410-414.
Stronkhorst, J., Schipper, C., Brils, J., Dubbeldam, M., Postma, J., & van de Hoeven, N.
(2003). Using marine bioassays to classify the toxicity of Dutch harbor sediments.
Environ. Toxicol. Chem. 22, 1535-1547.
Stronkhorst, J., van Hattum, B., Bowmers, T. (1999). Bioaccumulation and toxicity of
tributyltin to a burrowing heart urchin and an amphipod in spiked, silt marine
sediments. Environ. Toxicol. Chem., 18, 2343-2351.
Sugandhi, S., Joshi, V. M. & Ravi, P. (2014). Studies on natural and anthropogenic
radionuclides in sediment and biota of Mumbai Harbour Bay. J. Radioanal. Nucl.
Chem. 300(1), 67-70.
Sundberg, H., Tjärnlund, U., Åkerman, G., Blomberg, M., Ishaq, R., Grunder, K., . . . Balk, L.
(2005). The distribution and relative toxic potential of organic chemicals in a PCB
contaminated bay. Mar. Pollut. Bull. 50(2), 195-207.
Syvitski, J.P., Vörösmarty, C.J., Kettner, A.J. & Green, P. (2005). Impact of humans on the
flux of terrestrial sediment to the global coastal ocean. Science, 308(5720), 376-380.
Szmytkiewicz, A., & Zalewska, T. (2014). Sediment deposition and accumulation rates
determined by sediment trap and 210
Pb isotope methods in the Outer Puck Bay (Baltic
Sea). Oceanologia, 56(1), 85-106.
Tang, C. W.-y., Ip, C. C.-m., Zhang, G., Shin, P. K. S., Qian, P.-y., & Li, X.-d. (2008). The
spatial and temporal distribution of heavy metals in sediments of Victoria Harbour,
Hong Kong. Mar. Pollut. Bull., 57(6-12), 816-825.
Tanner, P.A., Leong, L.S, & Pan, S.M. (2000). Contamination of heavy metals in marine
sediment cores from Victoria Harbour, Hong Kong. Mar. Pollut. Bull. 40(9), 769-779.
Ten Hallers-Tjabbes, C.C., Kemp, J.F. & Boon, J.P. (1994). Imposex in whelks (Buccinum
undatum) from the open North Sea: Relation to shipping traffic intensities. Mar.
Pollut. Bull. 28, 311-313.
Tesi, T., Miserocchi, S., Goňi, M.A., Langone, L., Boldrin, A. Turchetto, M. (2007).
Organic matter origin and distribution in suspended particulate materials and surficial
sediments from the western Adriatic Sea (Italy). Estuar. Coast. Shelf Sci. 73(3), 431-
446.
Tessier, A., Campbell, P. G. C., & Bisson, M. (1979). Sequential extraction procedure for the
speciation of particulate trace metals. Anal. Chem., 51(7), 844-851.
Literature Review
70
Thain, J., & Bifield, S. (2002). Biological effects of contaminants: sediment bioassay using
the polychaete Arenicola marina: International Council for the Exploration of the Sea.
Thomas, M., Lazartigues, A., Banas, D., Brun-Bellut, J. & Feidt, C. (2102). Organochlorine
pesticides and polychlorinated biphenyls in sediments and fish from freshwater
cultured fish ponds in different agricultural contexts in north-eastern France.
Ecotoxicol. Environ. Safety, 77, 35-44.
Ulanovsky, A., Pröhl, G., & Gómez-Ros, J. (2008). Methods for calculating dose conversion
coefficients for terrestrial and aquatic biota. J. Environ. Radioact., 99(9), 1440-1448.
UNSCEAR. (2000). Sources and effects of ionizing radiation: sources (Vol. 1). New York:
United Nations Publications.
Uwadiae, R.E. (2010). An inventory of the benthic macrofauna of Epe Lagoon, southwest
Nigeria. J. Sci. Res. Develop. 12, 161-171.
van Dam, R.A., Harford, A.J., Houston, M.A., Hogan, A.C. & Negri, A.P. (2008). Tropical
marine toxicity testing in australia: a review and recommendations. Australasian J.
Ecotoxicol., 14, 55-88.
van den Heuvel-Greve, M., Postma, J., Jol, J., Kooman, H., Dubbeldam, M., Schipper, C., &
Kater, B. (2007). A chronic bioassay with the estuarine amphipod Corophium
volutator: Test method description and confounding factors. Chemosphere, 66, 1301-
1309.
van Hullebusch, E.D., Lens, P.N.L. & Tabak, H.H. (2005). Developments in bioremediation
of soils and sediments polluted with metals and radionuclides. 3. Influence of chemical
speciation and bioavailability on contaminants immobilization/mobilization bio-
processes. Rev. Environ. Sci. Biotechnol., 4(3), 185–212.
Van Rijn, L.C. (2005). Estuarine and coastal sedimentation problems. Int. J. Sediment Res.
20(1):39-51.
Vikas, M., & Dwarakish, G.S. ( 2015 ). Coastal Pollution: A Review. Aquat. Procedia, 4,
381-388.
Volesky, B. (2001). Detoxification of metal-bearing effluents: biosorption for the next
century. Hydrometallurgy. 59, 203-216.
Walker, K., Vallero, D.A. & Lewis, R.G., 1999. Factors influencing the distribution of lindane
and other hexachlorocyclohexanes in the environment. Environ. Sci. Technol. 33(24),
4373-4378.
Literature Review
71
Wang, S., Jia, Y., Wang, S., Wang, X., Wang, He., Zhao, Z. & Liu, B. (2010). Fractionation
of heavy metals in shallow marine sediments from Jinzhou Bay, China. J. Environ.
Sci. 22(1), 23-31.
Wang, Z., Liu, Z., Xu, K., Mayer, L.M., Zhang, Z., Kolker, A.S. and Wu, W. (2014).
Concentrations and sources of polycyclic aromatic hydrocarbons in surface coastal
sediments of the northern Gulf of Mexico. Geochem. Transact. 15, 2.
Wang, X.-C., Zhang, Y.-X. & Chen, R.F. (2001). Distribution and partitioning of polycyclic
aromatic hydrocarbons (PAHs) in different size fractions in sediments from Boston
Harbor, United States. Mar. Pollut. Bull. 42(11), 1139-1149.
WHO (World Health Organisation) (1989). DDT and its derivatives: Environmental aspects.
Environmental Health Criteria 83. Geneva.
Willett, K.L., Ulrich, E.M. & Hites, R.A. (1998). Differential toxicity and environmental fates
of hexachlorocyclohexane isomers. Environ. Sci. Technol. 32(15), 2197-2207.
Williams, C. (1996). Combating marine pollution from land-based activities: Australian
initiatives. Ocean & Coastal Manage. 33(1-3), 87–112.
Xinwei, L., Lingqing, W., & Xiaodan, J. (2006). Radiometric analysis of Chinese commercial
granites. J. Radioanal Nucl. Chem., 267(3), 669-673.
Yan, B., Abrajano, T. A., Bopp, R. F., Benedict, L. A., Chaky, D. A., Perry, E., . . . Keane, D.
P. (2006). Combined application of δ13C and molecular ratios in sediment cores for
PAH source apportionment in the New York/New Jersey harbor complex. Org.
Geochem., 37(6), 674-687.
Yang, R.-q., Jiang, G.-b., Zhou, Q.-f., Yuan, C.-g. & Shi, J.-b. (2005). Occurrence and
distribution of organochlorine pesticides (HCH and DDT) in sediments collected from
East China Sea. Environ. Int., 31(6), 799-804.
Yang, Y., Woodward, L.A., Li, Q.X. & Wang, J. (2014). Concentrations, Source and Risk
Assessment of Polycyclic Aromatic Hydrocarbons in Soils from Midway Atoll, North
Pacific Ocean. PLoS One, 9(1): 1-7.
Yeager, K., Santschi, P., Phillips, J. & Herbert, B. (2005). Suspended sediment sources and
tributary effects in the lower reaches of a coastal plain stream as indicated by
radionuclides, Loco Bayou, Texas. Environ. Geol. 47(3), 382-395.
Yilgor, S., Kucuksezgin, F., & Ozel, E. (2012). Assessment of metal concentrations in
sediments from Lake Bafa (Western Anatolia): an index analysis approach. Bulletin of
Environ. Contam. Toxicol., 89(3), 512-518.
Literature Review
72
Yim, U.H., Hong, S.H. & Shim, W.J. (2007). Distribution and characteristics of PAHs in
sediments from the marine environment of Korea. Chemosphere, 68, 85-92
Yunker, M.B., Macdonald, R.W., Brewer, R., Sylvestre, S., Tuominen, T., Sekela, M.,
Mitchell, R.H., Paton, D.W., Fowler, B.R., Gray, C., Goyette, D. & Sullivan, D.
(2000). Assessment of natural and anthropogenic hydrocarbon inputs using PAHs as
tracers. The Fraser River basin and Strait of Georgia, 1987-1997. Burrard Inlet
Environmental Action Programme, Canada.
Yunker, M.B., Macdonald, R.W., Vingarzan, R., Mitchell, R.H., Goyette, D. & Sylvestre, S.
(2002). PAHs in the Fraser River basin: a critical appraisal of PAH ratios as indicators
of PAH source and composition. Org. Geochem. 33(4), 489-515.
Zaborska, A., Carroll, J., Papucci, C., & Pempkowiak, J. (2007). Intercomparison of alpha and
gamma spectrometry techniques used in 210
Pb geochronology. J. Environ. Radioact.,
93(1), 38-50.
Zhou, J., Ma, D., Pan, J., Nie, W., & Wu, K. (2008). Application of multivariate statistical
approach to identify heavy metal sources in sediment and waters: a case study in
Yangzhong, China. Environ. Geol. 54(2), 373-380.
Zhu, H-n., Yuan, X-z., Zeng, G-m., Jiang, M., Liang, J., Zhang C., Yin, J., Huang H-j., Liu,
Z-f. & Jiang, H-w. (2012). Ecological risk assessment of heavy metals in sediments of
Xiawan Port based on modified potential ecological risk index. Trans. Nonferrous
Met. Soc. China, 22, 1470-1477.
Chapter 3
Radioactivity Concentrations and
their Radiological Significance in
Sediments of the Tema Harbour
(Greater Accra, Ghana)
A modified version of this chapter was published as: Botwe, B. O., Schirone, A., Delbono, I.,
Barsanti, M., Delfanti, R., Kelderman, P., Nyarko, E., & Lens, P. N. L. (2017). Radioactivity
concentrations and their radiological significance in sediments of the Tema Harbour (Greater
Accra, Ghana). Journal of Radiation Research and Applied Sciences, 10, 63-71.
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
74
Abstract
Studies on environmental radioactivity in tropical Africa are scarce. Therefore, a baseline
study of natural (238
U, 210
Pb, 226
Ra, 232
Th, 228
Ra, 228
Th, 40
K) and anthropogenic (137
Cs)
radionuclides was carried out on Tema Harbour (Greater Accra, Ghana) surface sediments and
on their radiological significance. Grab surface sediment samples were collected from 21
stations within the Tema Harbour and their specific activities measured by gamma
spectrometry. The mean sediments specific activities (Bq.kg-1
dw) were 34 for 238
U, 210 for
210Pb, 14 for
226Ra, 30 for
232Th, 29 for
228Ra, 31 for
228Th, 320 for
40K, and 1.5 for
137Cs.
Large 238
U/226
Ra disequilibria were observed in the harbour sediments and a complex
dynamics of several mixed sources of sediments within the Tema Harbour can be inferred
from the spatial variations in the specific activities. The estimated total absorbed dose rate in
air (D), radium equivalent activity (Raeq), external hazard index (Hex), annual gonadal dose
equivalent (AGDE) and annual effective dose equivalent (AEDE) indicated no significant
radiological risks from the sediment radioactivity concentrations. Application of the
Environmental Risk from Ionising Contaminants Assessment and Management tool (ERICA)
confirmed that the potential dose rates to biota from the sediment radioactivity concentrations
are unlikely to pose appreciable ecological risks. The radioactivity levels are compared with
levels reported in sediments from other coastal areas of the world.
3.1. Introduction
Radionuclides constitute an important source of ionising radiation exposure to human and
non-human populations (Kam & Bozkurt, 2007; UNSCEAR, 2000), which can cause harmful
biological effects such as DNA damage and cancer (Little, 2003; Ravanat et al., 2014; Schmid
& Schrader, 2007). Radionuclides such as 238
U, 210
Pb, 226
Ra, 232
Th, 228
Ra, 228
Th and 40
K are
widely distributed in the environment as a result of their natural occurrence in the Earth‘s
crust or the atmosphere. The human population worldwide receives an average annual
radiation dose of 2.4 mSv.y-1
, about 80% of which comes from naturally-occurring
radionuclides, the remaining part is largely due to artificial sources of which fallout
radionuclides account for only 0.4% (UNSCEAR, 2000). Fallout radionuclides such as 90
Sr,
137Cs and
239+240Pu are derived mainly from global nuclear tests conducted between the mid
1940s and the 1980s, as well as from nuclear accidents (Livingston & Povinec, 2000). In
addition to their potential ionising effects, radionuclides may be toxic and can undergo
bioconcentration and bioaccumulation (Hassona et al., 2008; Sirelkhatim et al., 2008) and
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
75
adversely impact human and ecosystem health. Assessment of radioactivity in the
environment is useful for the protection of human health and the environment from the
harmful effects of ionising radiation, and is therefore of great interest (Ulanovsky et al.,
2008). Most naturally-occurring and fallout radionuclides can be detected and measured at
extremely low concentrations; this makes them excellent tracers for many environmental
processes as well as unique dating tools. Thus, they have found a wide range of applications
in environmental studies such as isotope hydrogeology (Divine & McDonnel, 2005), water
masses circulation (Broecker, 1982), sediment dating and sedimentation (Hernandez, 2016;
Mahu et al., 2016; Mabit et al., 2014).
Although the West African coastal environment lacks the presence of nuclear industries, it
may be impacted by contaminated areas as a result of ocean and atmospheric dispersal and
redistribution. Furthermore, anthropogenic activities in the West African coastal environment
such as shipping, offshore oil and gas exploration and production, mining, industrialisation,
urbanisation, and agricultural production can potentially add to measured levels of
radionuclides in the environment (Al-Trabulsy et al., 2011; El Mamoney & Khater, 2004;
Nyarko et al., 2011). In the coastal environment, harbours may be particularly susceptible to
anthropogenic influences and their sediments can act as sinks for radionuclides (Sugandhi et
al., 2014). Harbours have hence been areas of interest when investigating radionuclide
contamination in the coastal environment (Akram et al., 2006; Kumar et al., 2013;
Papaefthymiou et al., 2007; Sam et al., 1998; Sugandhi et al., 2014). Sediment contamination
by radionuclides of the 238
U and 232
Th decay-series and 40
K is of particular interest from
radiological point of view, as they can form the basis of radiological assessments for the
human population. The Environmental Risk from Ionising Contaminants Assessment and
Management tool (ERICA) developed by the European Commission provides an integrated
approach to the assessment and management of environmental risks from ionising radiation
(Beresford et al., 2007) and can be applied to assess the potential ecological impact of
radionuclide-contaminated environments.
Currently, there is not much information on radioactivity levels in the coastal marine
environment of the West African region, including Ghana. In Ghana, the few radioactivity
studies in the coastal environment have focused on beach sediments (Amekudzie et al., 2011;
Nyarko et al., 2011), estuarine sediments (Mahu et al., 2016) and produce water from offshore
oil fields (Kpeglo et al., 2016). Due to rapid growth of urbanisation and industrialisation in
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
76
Tema, increasing maritime traffic and infrastructural expansion works at the Tema Port likely
intensify chemical contamination in the harbour. Monitoring of such developing coastal areas
is, therefore, essential to ensure that these socio-econonic and develomental activities do not
adversely affect human health and the proper functioning of coastal aquatic ecosystems. The
objective of this study was to assess the specific activities of natural (238
U, 210
Pb, 226
Ra, 232
Th,
228Ra,
228Th and
40K) and anthropogenic (
137Cs) radionuclides in surface sediments from the
Tema Harbour in Ghana and their radiological and radioecological significance.
3.2. Materials and Methods
3.2.1. Description of the study area
The Tema Harbour, situated in the Gulf of Guinea along the Ghana coast at Tema (Fig. 3.1), is
semi-enclosed with a water area of 1.7 km2 within a wider harbour zone of 3.9 km
2. It consists
of the Main Harbour, the Fishing Harbour comprising the Inner Fishing Harbour, the Outer
Fishing Harbour, and the Canoe Basin. Water depths range from 7.0-11.5 m for the Main
Harbour, 7.5-8.5 m for the Fishing Harbour and 3.0-5.0 m for the Canoe Basin. The Main
Harbour has 14 berths, a total of 4,580 m breakwater, a shipyard and dry dock for ship repairs,
and a 240 m wide access channel. The harbour does not receive riverine inflows, but does
receive wastewater from the Tema Township. The Fishing Harbour serves as a landing site for
fishing vessels, where repairs and re-fuelling of marine crafts are also carried out. A 2010
feasibility study report by Halcrow Engineers (unpublished) on the Tema Harbour revealed
that it is underlain mainly by gneiss rocks composed of feldspar, quartz and micaceous
minerals. The Tema Harbour is located in an industrial environment and thus, it is subject to
industrial activities.
3.2.2. Sediment sampling
Grab surface sediment samples were collected in November 2013 from 21 stations within the
Tema Harbour (Fig. 3.1), excluding rocky areas and berths where ships had docked (e.g. the
area between S7 and S14). Fourteen (14) of the sampling stations were located in the Main
Harbour (S1-S14), three (3) stations in the Canoe Basin (S15-S17), and two (2) stations each
in the Inner Fishing Harbour (S18 and S19) and the Outer Fishing Harbour (S20 and S21).
Geographical coordinates of the sampling stations were recorded using a Garmin Global
Positioning System (GPS). At each station, the redox potential (Eh) was measured in situ near
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
77
the sediment-water interface using a Hanna multi-parameter probe (HI 9829, Hanna
Instruments, USA).
Fig 3.1 Map of Tema Harbour (Greater Accra, Ghana) showing sediment sampling
locations
Sediment samples were collected using a 3.5 L Ekman bottom grab sampler. The sampling
locations were approximately 200 m apart, covering a wide area and range of water depths to
provide representative data on the radionuclide distribution in the harbour. To minimise
potential loss of fine particles via leakage of water from the grab, it was ensured that only
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
78
grabs that arrived firmly closed on the deck were sampled for analysis. In addition, only grabs
that were not filled with sediment to the lid were used to assure minimal disturbance of the
surface sediments.
About 100 g wet weight portions of surface sediments were taken with a clean plastic spoon
into polyamide Rilsan® bags and securely closed. With extremely low potential for diffusion
of materials across their surfaces (http://tub-ex.com/products/rilsan/), Rilsan® bags are
suitable for collection and storage of sediment samples and they have been used in
environmental monitoring programmes (Serigstad et al., 2010). To minimise contamination
from the grab, sediments in direct contact with the grab were not used and the sampling spoon
was washed with deionised water after each sampling. All sediment samples were kept on ice
and transported to the Chemistry Laboratory at the Ghana Atomic Energy Commission
(Greater Accra, Ghana) for further analyses.
3.2.3. Sample analyses
For the analyses of radionuclides, wet sediment samples were oven-dried at 50°C till constant
weight. Radiometric analyses of sediment samples were conducted at the ENEA S. Teresa
laboratory (Italian National Agency for New Technologies, Energy and Sustainable Economic
Development, La Spezia, Italy). The sediment samples were ground and placed in 5 g plastic
vials of standard geometry, closed and sealed air-tight, and then stored for at least 22 days to
ensure secular equilibrium between the parent nuclides and their short-lived daughter
nuclides. The sealed samples were then counted for 2-3 days, and activities measured for
210Pb at 46.5 keV,
214Pb at 352 keV,
212Pb at 239 keV,
208Tl at 583 KeV,
228Ac at 338 and
911.0 keV, 234
Th at 63.3 and 92.5 keV, 40
K at 1460 keV and 137
Cs at 662 keV. The measured
activities were decay-corrected with respect to the date of sediment sampling (Sirelkhatim et
al., 2008) and associated errors were determined from l-sigma counting statistics (Nyarko et
al., 2011). The activity of 228
Th was obtained from the activity of its daughter 212
Pb
radionuclide and 226
Ra and 228
Ra from the activities of 214
Pb and 228
Ac, respectively. The
average activity of 228
Ac and 212
Pb was used as a proxy for 232
Th activity. Since no
unsupported 234
Th (234
Thexc) was observed, the supported 234
Th activity was used as a proxy
for 238
U activity.
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
79
Samples were analysed using a Gamma spectrometer coupled to an ORTEC low background
intrinsic germanium coaxial detector (17.6% absolute efficiency, 1.8 keV nominal resolution
at 662 keV 137
Cs gamma emission). Prior to the sample radioactivity analyses, the Gamma ray
detectors were calibrated for measurement of 40
K using the IAEA-385 Certified Reference
Material (CRM), while calibrations for 238
U series radionuclides were performed using the
CANMET (Canada Centre for Mineral and Energy Technology) Reference Standard (DL1a),
being a U-Th ore in which 210
Pb and 226
Ra exist in secular equilibrium. Calibrations for 232
Th
series radionuclides were also performed using the IAEA Reference Standard (RGTh-1)
prepared by CANMET, while calibration for 137
Cs was performed using the Eckert & Ziegler
Analytics Reference Standard (QCYA48). Quality of all results was routinely checked by
analysing IAEA-300 and IAEA-315 Reference Materials as well as detector blanks (empty
sample containers) processed in a similar way as the actual samples. Correction of measured
activities for self-adsorption effects was done based on measurements of the attenuation of a
known 210
Pb Gamma source by the samples.
3.2.4. Radiological risk assessment
Dredged radioactive-contaminated harbour sediments may be disposed of on land or used for
other purposes such as building, which can potentially result in human exposure to ionising
radiations and cause radiological effects. For human protection and appropriate handling of
radioactive-contaminated sediments, it is essential to characterise the associated potential
radiological risks. Five radiological hazard indices were estimated following established
formulae to characterise the potential radiation dose to humans resulting from exposure to
sediment radioactivity, viz. (1) total absorbed dose rate in air (D), (2) radium equivalent
activity (Raeq), (3) external hazard index (Hex), (4) annual gonadal dose equivalent (AGDE),
and (5) annual effective dose equivalent (AEDE).
The D expresses the rate of exposure to gamma radiation in air at 1m above the ground due to
the activities of 226
Ra, 232
Th and 40
K in the sediment samples. Raeq is a weighted sum of the
specific activity of 226
Ra, 232
Th and 40
K in a sediment sample, which allows comparison with
their individual 226
Ra, 232
Th and 40
K specific activities (Sugandhi et al., 2014). Hex is a
measure of the indoor radiation dose rate associated with external gamma radiation exposure
from natural radionuclides in building materials and it is important when considering the
suitability of sediments as building materials (Xinwei et al., 2006). For human health safety,
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
80
the value of Hex must not exceed 1.0 (Kurnaz et al., 2007; Xinwei et al., 2006). Owing to their
relatively higher sensitivity to ionising radiation compared to other organs of the body, the
gonads are considered to be at a high risk of radiation exposure and are therefore of great
interest in radiological assessment (Kurnaz et al., 2007). The AGDE estimates the potential
radiation dose that the gonads may receive from 226
Ra, 232
Th and 40
K. It is also usual to
convert D to AEDE to assess the dose rate to an individual from outdoor gamma radiation
over a period of one year.
The D and Raeq were calculated using Eq. 1 and 2, respectively, following (El Mamoney &
Khater, 2004):
D (nGy.h-1
) = 0.462ARa + 0.604ATh + 0.0417AK (1)
Raeq (Bq.kg-1
) = ARa + 1.43ATh + 0.077AK (2)
Hex was calculated using Eq. 3 following (Xinwei et al., 2006):
Hex = (ARa/370) + (ATh/259) + (AK/4810) (3)
AGDE and AEDE were calculated using Eq. 4 and 5, respectively, following (Kurnaz et al.,
2007).
AGDE (µSv.y-1
) = 3.09ARa + 4.18ATh + 0.314AK (4)
AEDE (µSv.y-1
) = D (nGy.h-1
) x 8760 h x 0.2 x 0.7 Sv.Gy.y-1
x 10-3
(5)
3.2.5. Radioecological risk assessment
Radioactivity contamination in sediments may put aquatic organisms at risk of ionising
radiation effects. Therefore, the ERICA tool (version 1.2) was applied to assess the potential
dose rates to organisms in the harbour. A detailed description of the ERICA tool can be found
in literature (Beresford et al., 2007; Brown et al., 2008; Larsson, 2008). The tool is based on
data gathered from extensive radioecological and dosimetric studies and uses generalised
ecosystem representations, also referred to as reference organisms (Beresford et al., 2007). In
this context, a reference organism is defined as 'a series of entities that provide a basis for the
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
81
estimation of radiation dose rate to a range of organisms which are typical, or representative,
of a contaminated environment' (Beresford et al., 2007).
In this study, the ERICA tool was used to estimate radioactivities in ten (10) reference
organisms captured in the ERICA database, viz. phytoplankton, zooplankton, macroalgae,
pelagic/benthic fishes, mammals, crustaceans, mollusc-bivalves, sea anemones, and
polychaete worms. In estimating the radioactivities in the selected reference organisms, the
highest measured specific activities in the sediments (Bq.kg-1
dry wt.) were used as input data
to represent "worst case scenarios". Default concentration ratios for the reference organisms in
ERICA were then applied. Since, by default, 40
K was not included in the ERICA database,
this isotope was also not considered here.
Furthermore, a Tier 2 ERICA assessment was conducted to estimate the total dose rates to
biota, applying a default uncertainty factor of 3.0 in the ERICA tool to ensure there will be
less than 5% probability of modelled dose rates exceeding the screening dose rate. Since the
magnitude of biological effects varies with different types of ionising radiation (Schmid &
Schrader, 2007), default ERICA weighting factors of 10.0 for alpha, 1.0 for beta/gamma, and
3.0 for low beta radiation were applied to give appropriate weights to the dose rates. As dose
rate to biota is a function of the duration of exposure, a default ERICA occupancy factor of
1.0 (i.e., fraction of time that the organism spends at a specified location in its habitat) was
assigned to each reference organism, assuming they spend 100% of the time at their specified
locations (i.e. in the water column, on the sediment surface or inside the sediment).
3.3. Results and discussion
3.3.1. Radioactivity levels in the Tema Harbour sediments
The specific activities of 238
U, 210
Pb, 226
Ra, 228
Ra, 228
Th, 232
Th, 40
K and 137
Cs in the surface
sediment samples are shown in Table 3.1. The specific activities of 40
K were relatively higher
than those of the other radionuclides, ranging from 250 to 570 Bq.kg-1
with a mean of 320
Bq.kg-1
. Doyi et al. (2013) reported higher levels of 40
K and 232
Th for rocks and ore from
mines in the Upper East Region of Ghana in the ranges of 950-2800 and 81-880 Bq.kg-1
,
respectively, with a higher mean 238
U level of 66 (± 8) Bq.kg-1
. The levels of 210
Pb (except at
station S16) were markedly higher than those of 238
U, 226
Ra, 232
Th, 228
Ra and 228
Th. Their
mean value, 210 (± 10) Bq.kg-1
(~200 Bq.kg-1
for unsupported 210
Pb) is to some extent higher,
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
82
but comparable to the values of unsupported 210
Pb found by Mahu et al. (2016) in the upper
layers of sediment cores sampled in the Amisa (103 Bq.kg-1
), Sakumo II (157 Bq.kg-1
) and
Volta (123 Bq.kg-1
) estuaries in Ghana, respectively.
In coastal marine sediments, an excess of 228
Th above that supported by the parents 232
Th or
228Ra has often been reported, and used for radiometric dating (Koide et al., 1973). In the
Tema Harbour sediments, the specific activities of 232
Th, 228
Ra and 228
Th were comparable
within the involved uncertainties. Specific activities of 137
Cs in the sediments were markedly
low, varying from <0.3 to 2.3 Bq.kg-1
with a mean of 1.5 Bq.kg-1
. These values are
comparable to those reported by Mahu et al. (2016) for the surface layers of estuarine
sediments from Ghana (in the range 0-7 Bq.kg-1
). The low 137
Cs levels suggest low
atmospheric fallout in the study area, coupled with natural decay following its deposition
(Livingston & Povinec, 2000; Pfitzner et al., 2004) or remobilisation from sediment into
seawater (Sugandhi et al., 2014). Thus, Junge et al. (2013) have reported 137
Cs concentrations
in the range 0.5-6.5 Bq.kg-1
in farmland soils from Nigeria.
The levels of 210
Pb (20 ± 5 Bq.kg-1
) and 137
Cs (< 0.3 Bq.kg-1
) in the shallow station of the
Canoe Basin (S16) were very low compared to the levels found at the remaining stations.
Several mechanisms are involved in the distribution of radionuclides in the harbour such as
hydrodynamics, waves, tides, and vessel movements and dredging. The Canoe Basin is prone
to receive sediments from mixed sources including sand bars bordering one of its sides. In
May 2013, maintenance dredging was carried out in the Canoe Basin to ensure safer
navigation and increase berthing capacity for the operation of canoes. Dredging can
potentially remove contaminated sediments while influx of sand may cause dilution, and may
partly account for the low radioactivity levels of 210
Pb and 137
Cs at S16. In the Main Harbour,
the 210
Pb levels at stations S7 (130 ± 10 Bq.kg-1
), S11 (110 ± 10 Bq.kg-1
) and S13 (130 ± 10
Bq.kg-1
) were relatively lower than those at the other stations. This may partly be due to a
dilution effect of the discharges of industrial wastewater and sand channelled into the harbour
at S7, which can also affect neighbouring areas such as stations S13 and S11. On the contrary,
Table 3.1 shows that these same three stations (S7, S11 and S13) recorded relatively higher
levels of 40
K, possibly due to organic enrichment in sediments as a result of the waste water
discharges.
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
83
The ratios of 238
U/226
Ra, 238
U/210
Pb and 210
Pb/226
Ra were in the ranges of 1.4-3.5, 0.1-0.4 and
1.3-22.4, respectively. The departures of these ratios from 1.0 indicate disequilibria, a general
characteristic of marine surface sediments previously observed by others (Chen & Huh, 1999;
Koide et al., 1973), which may be caused by anthropogenic influences (Al-Trabulsy et al.,
2011; El Mamoney & Khater, 2004; Nyarko et al., 2011; UNSCEAR, 2000).
Table 3.1 Radioactivity concentrations (Bq.kg-1 dry wt.) in Tema Harbour surface
sediments and water depth and Eh at the sampling stations
238U series radionuclides
232
Th series
radionuclides 40
K 137
Cs
SS WD
(m)
Eh
(mV) 238
U 210
Pb 226
Ra 232
Th*
228Ra
228Th
S1 10 -96 30 ± 6 230 ± 10 12 ± 2 21 ± 3 18 ± 2 24 ± 1 250 ± 10 1.6 ± 0.4
S2 7 -128 39 ± 5 200 ± 10 11 ± 1 25 ± 3 24 ± 2 26 ± 1 260 ± 10 1.7 ± 0.5
S3 8.5 -100 43 ± 5 250 ± 10 13 ± 1 26 ± 4 26 ± 3 25 ± 1 270 ± 10 2.0 ± 0.5
S4 8 -70 40 ± 4 260 ± 10 18 ± 2 32 ± 4 30 ± 3 33 ± 1 350 ± 10 1.1 ± 0.5
S5 8 -65 28 ± 5 250 ± 10 14 ± 2 21 ± 3 19 ± 2 22 ± 1 250 ± 10 1.1 ± 0.5
S6 8 -94 28 ± 4 250 ± 10 17 ± 2 70 ± 4 67 ± 3 72 ± 1 330 ± 10 1.3 ± 0.5
S7 8 -90 28 ± 4 130 ± 10 13 ± 1 37 ± 3 34 ± 2 40 ± 1 460 ± 20 0.9 ± 0.5
S8 9 -80 28 ± 4 210 ± 10 13 ± 1 19 ± 3 18 ± 2 20 ± 1 270 ± 10 1.2 ± 0.4
S9 8.5 -80 35 ± 4 290 ± 10 16 ± 2 27 ± 3 24 ± 2 29 ± 1 290 ± 10 2.3 ± 0.5
S10 9.5 -78 32 ± 4 230 ± 10 15 ± 1 26 ± 3 24 ± 2 28 ± 1 350 ± 10 1.1 ± 0.4
S11 8.5 70 21 ± 4 110 ± 10 10 ± 1 38 ± 3 36 ± 2 39 ± 1 570 ± 20 0.5 ± 0.3
S13 9 50 47 ± 7 130 ± 10 14 ± 1 44 ± 4 44 ± 3 43 ± 1 390 ± 20 2.2 ± 0.5
S14 7.5 70 36 ± 3 240 ± 10 17 ± 1 29 ± 3 27 ± 2 31 ± 1 330 ± 10 1.1 ± 0.4
S15 10 95 42 ± 4 280 ± 10 16 ± 1 28 ± 3 25 ± 2 31 ± 1 330 ± 10 1.4 ± 0.4
S16 3 400 24 ± 4 20 ± 5 16 ± 1 37 ± 3 36 ± 2 38 ± 1 330 ± 10 < 0.3
S17 4 -210 26 ± 5 230 ± 10 13 ± 2 34 ± 3 35 ± 2 32 ± 1 310 ± 10 1.9 ± 0.5
S18 5 -140 32 ± 4 230 ± 10 13 ± 2 25 ± 3 21 ± 2 28 ± 1 310 ± 10 1.5 ± 0.4
S19 8 -115 42 ± 5 310 ± 20 14 ± 1 23 ± 3 22 ± 2 23 ± 1 270 ± 10 1.9 ± 0.4
S20 8 -110 35 ± 6 240 ± 10 11 ± 2 24 ± 4 23 ± 3 25 ± 1 300 ± 10 1.6 ± 0.5
S21 8 -100 27 ± 4 170 ± 10 20 ± 1 26 ± 3 24 ± 2 27 ± 1 300 ± 10 1.4 ± 0.4
S22 8 -90 41 ± 5 170 ± 10 18 ± 1 28 ± 3 27 ± 2 29 ± 1 300 ± 10 1.5 ± 0.5
Mean - - 34 ± 5 210 ± 10 14 ± 1 30 ± 3 29 ± 2 31 ± 1 320 ± 10 1.5 ± 0.5
SS = sampling station; Errors are 1 standard deviation from counting statistics; *232
Th
activities are estimated from grand-daughters activities
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
84
The origin of the excess in 210
Pb found in sediments is well known, and it is the basis of the
210Pb-based radiometric method for dating recent sediments (Mabit et al, 2014). On the
contrary, the observed disequilibria between 238
U (derived from 234
Th activity, see Section
3.2.3) and 226
Ra may be ascribed to differences in geochemical behaviour of the radionuclides
(Koide et al., 1973). 226
Ra and 238
U are known for their different sorption and mobility
characteristics; 226
Ra and 238
U are less particle-reactive than Th isotopes with greater tendency
to diffuse from sediments into the surrounding seawater (Chen & Huh, 1999; Sirelkhatim et
al., 2008; Sugandhi et al., 2014). The higher levels of 238
U relative to 226
Ra in the sediments
may be due to diffusion and loss of Ra from sediment owing to its higher solubility in
seawater or higher leachability of 226
Ra from the harbour sediments than 238
U-234
Th. At the
time of sampling, the bottom water was anoxic, having Eh values in the range of -50 to -400
mV (Table 3.1), which may enhance immobilisation and precipitation of 238
U in the sediments
(El Mamoney & Khater, 2004). Mohamed et al. (2010) reported 228
Ra/226
Ra activity ratios in
the range 1.2-2.9 with 238
U/226
Ra activity ratios in the range 1.1-5.6 for southern South China
Sea surface sediments, which compare well with the ranges 1.4-3.9 and 1.6-3.5 found in this
work for 228
Ra/226
Ra and 238
U/226
Ra activity ratios, respectively (Table 3.1).
The mean specific activity levels in the Tema Harbour sediments and levels reported for
other areas are shown in Table 3.2. With the exception of Labadi that recorded higher levels
of 226
Ra and 232
Th, the mean specific activity levels in the Tema Harbour sediments were
generally higher than those reported in sediments from other areas, i.e. Chorkor, James Town,
Nungua, Kokrobite, Teshie and Weija of the Greater Accra coast of Ghana (Amekudzie et al.,
2011). Nyarko et al. (2011) also reported lower specific activities of 210
Pb in beach sand
samples along the Ghana coast ranging from 1.6 up to 4.5 Bq.kg-1
and 137
Cs concentrations
below the detection limit of 0.4 Bq.kg-1
. The mean specific activity levels in the Tema
Harbour sediments were also higher than the levels reported for the Mediterranean coast of
Egypt (Higgy, 2000), but were comparable to levels reported for the Saudi coast of the Gulf of
Aqaba, except for their higher 40
K (Al-Trabulsy et al., 2011); the Red Sea coast of Egypt (El
Mamoney & Khater, 2004), Port Sudan and Sawakin Harbour of Sudan (Sam et al., 1998),
Patras Harbour, Greece (Papaefthymiou et al., 2007), Mumbai Harbour, India (Sugandhi et al.,
2014), and the Karachi Harbour, Pakistan (Sugandhi et al., 2014). The mean specific activity
levels of 238
U, 232
Th, 40
K and 137
Cs in the Tema Harbour sediments were, however, much
lower than those found in polluted sediments from the Caspian Sea coast of Iran (Abdi et al.,
2009). Mohamed et al. (2010) found comparatively higher levels of 226
Ra, 228
Ra, 238
U and
Table 3.2 Specific activity levels in Tema Harbour surface sediments and levels reported in sediments from other areas of the world
238U series radionuclides
(Bq.kg-1
)
232Th series radionuclides
(Bq.kg-1
)
40K
(Bq.kg-1
)
137Cs
(Bq.kg-1
) Reference
Sampling Station 238
U 210
Pb 226
Ra 232
Th 228
Ra 228
Th
Ghana coast
Chorkor - - 1.42 1.49 - - 21.31 - Amekudzie et al. (2011)
James Town - - 0.82 1.04 - - 14.67 - "
Labadi - - 140.8 732.6 - - 43.97 - "
Nungua - - 4.05 8.64 - - 41.17 - "
Kokrobite - - 3.74 6.63 - - 17.76 - "
Teshie - - 2.85 9.66 - - 61.01 - "
Weija - - 0.62 0.17 - - 8.6 - "
Tema Habour 34 210 14 30 29 31 325 1.5 This study
Other areas
Port Sudan, Sudan - - 11.05 - 10.35 - 311 7.02 Sam et al. (1998)
Sawakin Harbour, Sudan - - 12.61 - 6.18 - 192 4.51 "
Patras Harbour, Greece - - 22.6 24.5 - - 497 3.1 Papaefthymiou et al.
(2007)
Mumbai Harbour, India - - 10.6
12.7
436 21.6 Sugandhi et al. (2014)
Karachi Harbour, Pakistan
23.9 - 23.5 - 527 < 1.3 Akram et al. (2006)
Saudi coast, Gulf of Aqaba 16.9 - 11 22 19 - 641 3.5 Al-Trabulsy et al. (2011)
Red Sea coast, Egypt 25.5 26 24.6 - - - 427.5 - El Mamoney and Khater
(2004)
Mediterranean coast, Egypt 8.8 - 5 2.1 - - 46
Higgy (2000)
Caspian Sea coast, Iran 177 - - 117 - - 1085 131 Abdi et al. (2009)
Malaysia coast, South China
Sea 45.9
27.7 73.3 66.2 - - - Mohamed et al. (2010)
World average 35a 25
b 25
b,c,d,e 25
c,e - - 373
d,e -
aSureshGandhi et al.
(2014); bNyarko et al.
(2011); cQureshi et al.
(2014); dKurnaz et al.
(2007); eSugandhi et al.
(2014)
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
86
232Th for surface sediments from the Malaysia coast of the southern South China Sea.
Generally, the mean specific activity levels in the Tema Harbour sediments were comparable
to the reported worldwide averages (Nyarko et al., 2011; Papaefthymiou et al., 2007; Qureshi
et al., 2014; SureshGandhi et al., 2014), except for 210
Pb which was almost an order of
magnitude higher than its grandparent 226
Ra, due to the presence of unsupported 210
Pb.
3.3.2. Radiological significance of Tema Harbour sediment specific activity levels
The calculated hazard indices for the Tema Harbour sediments and hazard indices reported for
sediments from other areas of the world are presented in Table 3.3. The ranges (means) of D,
Raeq, Hex, AGDE, and AEDE for the Tema Harbour sediments were 29-64 nGy.h-1
(39 nGy.h-
1), 61-142 Bq.kg
-1 (82.7 Bq.kg
-1), 0.2-0.4 (0.2), 203-447 µSv.y
-1 (273 µSv.y
-1), and 35-78
µSv.y-1
(47 µSv.y-1
), respectively. These mean D, Raeq, Hex, AGDE, and AEDE values were
below the recommended values, although there were a few areas where the measured Raeq
(i.e. S4, S6, S7, S11, S13 and S16), ADGE (i.e. S6, S7, S11, S13 and S16) and AEDE (i.e. S6)
exceeded the recommended values. Thus, the radioactivity levels in the harbour sediments are
generally of little radiological concern for human health.
Compared to this study, Amekudzie et al. (2011) reported higher mean D (77 nGy.h-1
) and Hex
(0.5), but lower mean Raeq (9 Bq.kg-1
) values for sediments from Chorkor, James Town,
Nungua, Kokrobite, Teshie and Weija along the Greater Accra coast of Ghana (Table 3.3).
Comparable mean values of D (42 nGy.h-1
) and Raeq (101 Bq.kg-1
) were reported for the Red
Sea coast of Egypt by El Mamoney & Khater (2004), while a lower mean D value of 5.5
nGy.h-1
was reported for the Mediterranean coast of Egypt by Higgy (2000). Higher mean
values of D (63 nGy.h-1
), Raeq (176 Bq.kg-1
) and Hex (0.5) were reported for sediments from
the Caspian Sea coast by Abdi et al. (2009), while a lower mean Hex value of 0.1 was reported
for the Saudi coast of the Gulf of Aqaba by Al-Trabulsy et al. (2011).
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
87
Table 3.3 Calculated D, Raeq, Hex, AGDE and AEDE for Tema Harbour surface
sediments and sediments from other parts of the world as well as
recommended values
D
(nGy.h-1
)
Raeq
(Bq.kg-1
) Hex
AGDE
(µSv.y-1
)
AEDE
(µSv.y-1
) Reference
Tema Harbour
This study
S1 29 61 0.2 203 35
S2 31 67 0.2 220 38
S3 33 70 0.2 232 40
S4 42 90 0.2 297 51
S5 29 63 0.2 208 36
S6 64 142 0.4 447 78
S7 48 101 0.3 339 58
S8 29 61 0.2 204 35
S9 36 76 0.2 251 44
S10 37 79 0.2 265 46
S11 51 108 0.3 367 63
S13 49 106 0.3 348 60
S14 39 84 0.2 277 48
S15 38 82 0.2 270 47
S16 44 94 0.3 308 53
S17 39 85 0.2 278 48
S18 34 72 0.2 240 41
S19 31 67 0.2 222 38
S20 32 68 0.2 229 39
S21 37 80 0.2 263 46
S22 38 81 0.2 267 46
Mean 39 83 0.2 273 47
Mean values for
other areas
Caspian Sea coast,
Iran 63 176 0.5 - - Abdi et al. (2009)
Red Sea coast,
Egypt 42 101 - - -
El Mamoney and
Khater (2004)
Saudi coast, Gulf
of Aqaba - - 0.1 - -
Al-Trabulsy et al.
(2011)
Mediterranean
coast, Egypt 5.5 - - - - Higgy (2000)
Ghana coast 77 9 0.5 - 0.1 Amekudzie et al.
(2011)
Recommended
value 55
a,b 89
a 1.0
c 300
c 70
c
D (total absorbed dose rate in air); Raeq (radium equivalent activity); Hex (external hazard
index); AGDE (annual gonadal dose equivalent); AEDE (annual effective dose equivalent);
aKurnaz et al. (2007);
bAbdi et al. (2009);
cXinwei et al. (2006); - : not reported
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
88
3.3.3. Radioecological significance of Tema Harbour sediment radioactivity
Table 3.4 presents the estimated specific activity levels in the selected reference organisms.
Generally, biota exhibited potentially higher accumulation levels of 210
Pb (1.18-570 Bq.kg-1
)
relative to the other radionuclides (0-0.05 for 137
Cs; 0.82-14.4 for Ra; 0.01- 6.60 for Th, and
0.06-17.5 Bq.kg-1
for 238
U), possibly reflecting the relatively higher levels of 210
Pb in the
sediments. Thus, sediments may be an important source of 210
Pb exposure to biota. The levels
of 210
Pb were markedly high in phytoplankton, exceeding the levels in the sediments. This is
an indication of a high potential for 210
Pb bioaccumulation by phytoplankton as has been
reported by Hassona et al. (2008). Overall, phytoplankton exhibited the highest potential for
radionuclide exposure from sediment, suggesting that it could be a good bioindicator for
monitoring of radionuclide contamination in the Tema Harbour.
Apart from the 210
Pb levels in phytoplankton, the specific levels in all the reference organisms
were generally low compared to the levels in the sediments. This indicates that the
radionuclides associate mainly with the sediments, despite their potential for bioaccumulation
(Hassona et al., 2008; Sirelkhatim et al., 2008). This supports the view that sediments are the
major sinks for radionuclides in aquatic ecosystems (Sugandhi et al., 2014). The very low
specific activity levels of Th and 137
Cs in biota suggest that sediments may not be a major
exposure pathway of these radionuclides to biota in the harbour.
The ERICA-derived dose rates to biota are presented in Table 3.5. It shows that
phytoplankton could potentially receive higher dose rates from sediment radioactivity than the
other reference organisms, which corresponds to its higher bioaccumulation potential for
radionuclides (Table 3.4). The total dose rate to phytoplankton slightly exceeded the typical
maximum value in the ERICA database (see Table 3.5). Whereas the total dose rate to pelagic
fishes was similar to the typical minimum, that of crustaceans slightly exceeded the typical
minimum value, but fell below the typical average value. In the case of zooplankton,
macroalgae, benthic fishes, mammal, mollusc-bivalves and polychaete worms, the total dose
rates fell below their ERICA typical minimum values (Table 3.5). The total dose rates to all
the reference organisms fell below the screening dose rate of 400 µGy.h-1
, proposed by the
International Atomic Energy Agency (IAEA) and the United Nations Scientific Committee on
the Effects of Atomic Radiation (UNSCEAR) as the dose rate below which harmful effects
are unlikely to occur in organisms.
Table 3.4 Highest specific activities in Tema Harbour sediments (Bq.kg-1 d.w) and ERICA-derived specific activities in reference
organisms (Bq.kg-1 f.w)
Reference organisms
Sediment
Phyto-
plankton
Zoo-
plankton
Macro-
algae
Pelagic/Benthic
fishes Mammals Crustaceans
Mollusc-
bivalves
Sea
anemones
Polychaete
worms
137Cs 2.3 0 0.03 0.02 0.02 0.05 0.01 0.01 0.05 0.04
*Ra 67 14.4 1.02 1.13 1.76 2.06 1.08 0.82 1.76 1.76
210Pb 314 570 20 1.18 38.9 22.4 24.8 7.43 38.9 47.2
*Th 72 6.60 0.06 0.04 0.01 0.02 0.35 0.02 0.02 0.02
238U 47 3.85 0.07 1.47 0.16 0.16 0.06 0.57 17.5 17.5
*Ra is for both
226Ra and
228Ra;
*Th for both
232Th and
228Th
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
Table 3.5 ERICA-derived total dose rates to reference organisms and typical
maximum, minimum, and average values (uGy.h-1) in the ERICA database
Reference
Organism
Total dose
rate
Typical average
dose rate
Typical minimum
dose rate
Typical maximum
dose rate
Phytoplankton 2.11 0.38 0.13 2.00
Zooplankton 0.06 0.94 0.25 5.20
Pelagic fish 0.09 0.42 0.08 3.70
Mammal 0.10 1 0.23 5.80
Macroalgae 0.13 0.87 0.52 1.40
Benthic fish 0.12 0.58 0.24 1.20
Crustacean 0.16 0.59 0.12 1.90
Mollusc-bivalve 0.09 2 0.98 5.60
Sea anemones 0.54 4.20 1.90 8.80
Polychaete worm 0.58 1.6 0.94 2.5
It is worthy to note that the ERICA tool was used in this study as a screening tool to provide
estimates of the radioactivity levels in biota and associated total dose rates rather than their
accurate prediction. Furthermore, the estimated total dose rates to biota may be
underestimated since they were based on the specific activities of only 238
U, 210
Pb, 226
Ra,
228Ra,
228Th,
232Th and
137Cs. Measurement of radioactivity levels of
238U,
210Pb,
226Ra,
228Ra,
228Th,
232Th and
137Cs in different environmental matrices such as sediments, water and biota
from the harbour will be important to validate the predictive ability of the ERICA modelling
tool for the Tema Harbour ecosystem and is, therefore, recommended for future studies.
3.4. Conclusions
The radioactivity levels of 238
U, 210
Pb, 226
Ra, 232
Th, 228
Ra, 228
Th, 40
K and 137
Cs in surface
sediment from the Tema Harbour in Ghana have been assessed for the first time. The specific
activities of 40
K and 210
Pb were relatively higher than the levels of the other radionuclides in
the Tema Harbour sediments. Large disequilibria between 238
U and 226
Ra were found,
attributable to the dynamics of the sediments in the harbour. Apart from 210
Pb, the specific
activities of the natural radionuclides in the Tema Harbour sediments were comparable to
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
91
worldwide average values. Evaluation of total absorbed dose rate in air (D), radium equivalent
activity (Raeq), external hazard index (Hex), annual gonadal dose equivalent (AGDE) and
annual effective dose equivalent (AEDE) indicate that the potential dose rates to human from
the sediment radioactivity levels may not present significant risks to human health. Moreover,
the potential dose rates to biota derived from the ERICA assessment indicate low ecological
risks associated with the radioactivity levels in the harbour sediments. This study provides
baseline information on radioactivity levels in the Tema Harbour sediments for comparison to
future monitoring studies.
References
Abdi, M.R., Hassanzadeh, S., Kamali, M., & Raji, H.R. (2009). 238
U, 232
Th, 40
K and 137
Cs
activity concentrations along the southern coast of the Caspian Sea, Iran. Marine
Pollution Bulletin, 58(5), 658-662.
Akram, M., Qureshi, R., Ahmad, N., Solaija, T., Mashiatullah, A., Afzal, M., Faruq, M.U., &
Zeb, L. (2006). Concentration of natural and artificial radionuclides in bottom
sediments of Karachi Harbour/Manora Channel, Pakistan Coast (Arabian Sea).
Journal of the Chemical Society of Pakistan, 28(3), 306-312.
Al-Trabulsy, H., Khater, A., & Habbani, F. (2011). Radioactivity levels and radiological
hazard indices at the Saudi coastline of the Gulf of Aqaba. Radiation Physics and
Chemistry, 80(3), 343-348.
Amekudzie, A., Emi-Reynolds, G., Faanu, A., Darko, E., Awudu, A., Adukpo, O., Quaye,
L.A.N., Kpordzro, R., Agyeman, B., & Ibrahim, A. (2011). Natural radioactivity
concentrations and dose assessment in shore sediments along the coast of Greater
Accra, Ghana. World Applied Sciences Journal, 13(11), 2338-2343.
Beresford, N., Brown, J., Copplestone, D., Garnier-Laplace, J., Howard, B., Larsson, C.-M.,
Oughton, D., Prӧhl, G., Zinger, I. (2007). D-ERICA: An integrated approach to the
assessment and management of environmental risk from ionising radiation.
Description of purpose, methodology and application.
Broecker, W. (1982). Geochemical tracers and ocean circulation. Lamont-Doherty Geological
Observatory, Palisades, NY, 434-450.
Brown, J., Alfonso, B., Avila, R., Beresford, N.A., Copplestone, D., Pröhl, G., & Ulanovsky,
A. (2008). The ERICA tool. Journal of Environmental Radioactivity, 99(9), 1371-
1383.
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
92
Chen, H.Y., & Huh, C.A. (1999). 232
Th–228
Ra–228
Th disequilibrium in East China Sea
sediments. Journal of Environmental Radioactivity, 42(1), 93-100.
Divine, C.E., & McDonnell, J.J. (2005). The future of applied tracers in hydrogeology.
Hydrogeology Journal, 13(1), 255-258.
Doyi, I., Oppon, O., Glover, E., Gbeddy, G., & Kokroko, W. (2013). Assessment of
occupational radiation exposure in underground artisanal gold mines in Tongo, Upper
East Region of Ghana. Journal of Environmental Radioactivity, 126, 77-82.
El Mamoney, M., & Khater, A.E. (2004). Environmental characterization and radio-ecological
impacts of non-nuclear industries on the Red Sea coast. Journal of Environmental
Radioactivity, 73(2), 151-168.
Hassona, R.K., Sam, A.K., Osman, O.I., Sirelkhatim, D.A., & LaRosa, J. (2008). Assessment
of committed effective dose due to consumption of Red Sea coral reef fishes collected
from the local market (Sudan). Science of the Total Environment, 393(2–3), 214-218.
Hernández, J.-M.A. (2016). A 210
Pb-based chronological model for recent sediments with
random entries of mass and activities: Model development. Journal of Environmental
Radioactivity, 151, 64-74.
Higgy, R. (2000). Natural radionuclides and plutonium isotopes in soil and shore sediments
on Alexandria Mediterranean Sea coast of Egypt. Radiochimica Acta, 88(1), 47-54.
Junge, B., Mabit, L., Dercon, G., Walling, D., Abaidoo, R., Chikoye, D., & Stahr, K. (2010).
First use of the 137 Cs technique in Nigeria for estimating medium-term soil
redistribution rates on cultivated farmland. Soil and Tillage Research, 110(2), 211-
220.
Kam, E., & Bozkurt, A. (2007). Environmental radioactivity measurements in Kastamonu
region of northern Turkey. Applied Radiation and Isotopes, 65(4), 440-444.
Koide, M., Bruland, K.W., & Goldberg, E.D. (1973). Th-228/Th-232 and Pb-210
geochronologies in marine and lake sediments. Geochimica et Cosmochimica Acta,
37(5), 1171-1187.
Kpeglo, D., Mantero, J., Darko, E., Emi-Reynolds, G., Faanu, A., Manjón, G., Vioque, I.,
Akaho, E.H.K., & Garcia-Tenorio, R. (2016). Radiochemical characterization of
produced water from two production offshore oilfields in Ghana. Journal of
Environmental Radioactivity, 152, 35-45.
Kumar, A., Karpe, R., Rout, S., Joshi, V., Singhal, R.K., & Ravi, P.M. (2013). Spatial
distribution and accumulation of 226
Ra, 228
Ra, 40
K and 137
Cs in bottom sediments of
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
93
Mumbai Harbour Bay. Journal of Radioanalytical and Nuclear Chemistry, 295(2),
835-839.
Kurnaz, A., Küçükömeroğlu, B., Keser, R., Okumusoglu, N., Korkmaz, F., Karahan, G., &
Çevik, U. (2007). Determination of radioactivity levels and hazards of soil and
sediment samples in F rt na Valley (Rize, Turkey). Applied Radiation and Isotopes,
65(11), 1281-1289.
Larsson, C.-M. (2008). An overview of the ERICA Integrated Approach to the assessment and
management of environmental risks from ionising contaminants. Journal of
Environmental Radioactivity, 99(9), 1364-1370.
Little, M. (2003). Risks associated with ionizing radiation Environmental pollution and health.
British Medical Bulletin, 68(1), 259-275.
Livingston, H.D., & Povinec, P.P. (2000). Anthropogenic marine radioactivity. Ocean &
Coastal Management, 43(8), 689-712.
Mabit, L., Benmansour, M., Abril, J., Walling, D., Meusburger, K., Iurian, A.R., Bernard, C.,
Tarján, S., Owens, P.N., Blake, W.H., & Alewell, C. (2014). Fallout 210
Pb as a soil and
sediment tracer in catchment sediment budget investigations: a review. Earth-Science
Reviews, 138, 335-351.
Mahu, E., Nyarko, E., Hulme, S., Swarzenski, P., Asiedu, D. K., & Coale, K. H. (2016).
Geochronology and historical deposition of trace metals in three tropical estuaries in
the Gulf of Guinea. Estuarine, Coastal and Shelf Science, 177, 31-40.
Mohamed, C. A. R., Mahmood, Z. U. W., Ahmad, Z., & Ishak, A. K. (2010). Enrichment of
natural radium isotopes in the southern South China Sea surface sediments. Coastal
Marine Science, 34(1), 165-171.
Nyarko, E., Botwe, B., Ansong, J., Delfanti, R., Barsanti, M., Schirone, A., & Delbono, I.
(2011). Determination of 210
Pb, 226
Ra and 137
Cs in beach sands along the coastline of
Ghana. African Journal of Environmental Pollution and Health, 9, 17-23.
Papaefthymiou, H., Papatheodorou, G., Moustakli, A., Christodoulou, D., & Geraga, M.
(2007). Natural radionuclides and 137
Cs distributions and their relationship with
sedimentological processes in Patras Harbour, Greece. Journal of Environmental
Radioactivity, 94(2), 55-74.
Pfitzner, J., Brunskill, G., & Zagorskis, I. (2004). 137
Cs and excess 210
Pb deposition patterns in
estuarine and marine sediment in the central region of the Great Barrier Reef Lagoon,
north-eastern Australia. Journal of EnvironmentalRradioactivity, 76(1), 81-102.
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
94
Qureshi, A. A., Tariq, S., Din, K. U., Manzoor, S., Calligaris, C., & Waheed, A. (2014).
Evaluation of excessive lifetime cancer risk due to natural radioactivity in the rivers
sediments of Northern Pakistan. Journal of Radiation Research and Applied Sciences,
7(4), 438-447.
Ravanat, J., Breton, J., Douki, T., Gasparutto, D., Grand, A., Rachidi, W., & Sauvaigo, S.
(2014). Radiation-mediated formation of complex damage to DNA: a chemical aspect
overview. The British Journal of Radiology, 87(1035), 20130715.
Sam, A., ElGanawi, A., Ahamed, M., & ElKhangi, F. (1998). Distribution of some natural and
anthropogenic radionuclides in Sudanese harbour sediments. Journal of
Radioanalytical and Nuclear Chemistry, 237(1-2), 103-107.
Santschi, P.H., Murray, J.W., Baskaran, M., Benitez-Nelson, C.R., Guo, L.D., Hung, C.C.,
Lamborg, C., Moran, S.B., Passow, U., & Roy-Barman, M. (2006). Thorium
speciation in seawater. Marine Chemistry, 100(3–4), 250-268.
Schmid, E., & Schrader, T. (2007). Different biological effectiveness of ionising and non-
ionising radiations in mammalian cells. Advances in Radio Science, 5(1), 1-4.
Serigstad, B., Olsen, M., Mørk, T., Kristiansen, J., Wolinski, G., Gowing, S., Akam, D.N., &
Whitehead, N. (2010). Marine environmental survey of bottom sediments in Cabinda
and Soyo province, Angola. Cruise report No 4/2009.
Sirelkhatim, D., Sam, A., & Hassona, R. (2008). Distribution of 226
Ra–210
Pb–210
Po in marine
biota and surface sediments of the Red Sea, Sudan. Journal of Environmental
Radioactivity, 99(12), 1825-1828.
Sugandhi, S., Joshi, V. M., & Ravi, P. (2014). Studies on natural and anthropogenic
radionuclides in sediment and biota of Mumbai Harbour Bay. Journal of
Radioanalytical and Nuclear Chemistry, 300(1), 67-70.
SureshGandhi, M., Ravisankar, R., Rajalakshmi, A., Sivakumar, S., Chandrasekaran, A., &
Anand, D.P. (2014). Measurements of natural gamma radiation in beach sediments of
north east coast of Tamilnadu, India by gamma ray spectrometry with multivariate
statistical approach. Journal of Radiation Research and Applied Sciences, 7(1), 7-17.
Ulanovsky, A., Pröhl, G., & Gómez-Ros, J. (2008). Methods for calculating dose conversion
coefficients for terrestrial and aquatic biota. Journal of Environmental Radioactivity,
99(9), 1440-1448.
UNSCEAR. (2000). Sources and effects of ionizing radiation: sources (Vol. 1). New York
(Vol. 1): United Nations Publications.
Radioactivity Concentrations and their Radiological Significance in Sediments of the Tema Harbour (Greater Accra, Ghana)
95
Xinwei, L., Lingqing, W., & Xiaodan, J. (2006). Radiometric analysis of Chinese commercial
granites. Journal of Radioanalytical and Nuclear Chemistry, 267(3), 669-673.
Chapter 4
Assessment of DDT, HCH and
PAH Contamination and
Associated Ecotoxicological
Risks in Surface Sediments of
Coastal Tema Harbour (Ghana)
A modified version of this chapter was published as: Botwe, B.O., Kelderman, P., Nyarko, E.,
& Lens, P.N.L. (2017). Assessment of DDT, HCH and PAH contamination and associated
ecotoxicological risks in surface sediments of coastal Tema Harbour (Ghana). Marine
Pollution Bulletin, 115, 480-488.
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
98
Abstract
This study assessed DDTs, HCHs and PAHs contamination in sediments from the Tema
Harbour (Ghana) and the associated ecotoxicological risks. The results showed widespread
DDTs, HCHs and PAHs contamination in the harbour sediments with mean concentrations
ranging from 6.0-12.8, 2.8-12.7 and 2,750-5,130 µg.kg-1
d.w, respectively. The silt-clay and
total organic carbon contents of the sediments poorly correlated with the pollutant
concentrations. DDTs and HCHs contamination relate to past use of DDT and lindane, which
under the anoxic harbour conditions resulted in disproportionately higher concentrations of
p,p'-DDD and γ-HCH in the sediments. No conclusion could be drawn on the sources of
PAHs as either petrogenic or pyrogenic. The pollutant concentrations in the harbour
sediments, particularly γ-HCH, may pose high ecotoxicological risks. In comparison to a
previous study, this study indicates there has been a considerable reduction in PAH
contamination in the Tema Harbour since the last major oil spill in 2007.
4.1. Introduction
Chemical pollution of coastal marine ecosystems is a major global issue due to the adverse
human health, as well as their ecological and socioeconomic implications, such as degradation
of marine habitats, death of organisms and decline in biodiversity, contamination of food
sources and deprivation of livelihoods (Islam and Tanaka, 2004; Mestres et al., 2010).
Moreover, severely polluted ecosystems may be impossible or very costly to clean-up and
restore. Many coastal marine ecosystems have been polluted (Islam and Tanaka, 2004), and
many are under threat due the increasing coastal populations and developmental activities
(Birch and Hutson, 2009). Chemical pollution of coastal marine ecosystems is often linked to
intense human activities in the coastal zone, such as industrial production, shipping, crude oil
extraction, agriculture and sewage disposal (Islam and Tanaka, 2004; Birch and Hutson, 2009;
Smith et al., 2009; Mestres et al., 2010). Priority pollutants include
dichlorodiphenyltrichloroethane (DDT), hexachlorocyclohexane (HCH) and polycyclic
aromatic hydrocarbons (PAHs) due to the environmental persistence of these organic
pollutants, their long-range atmospheric transport, bioaccumulation along the food chain, as
well as their associated adverse biological effects such as toxicity, endocrine disruption,
cancer, mutations and reproductive anomalies (Willett et al., 1998; Wang et al., 2001; Islam
and Tanaka, 2004; King et al., 2004; De Luca et al., 2004; Nyarko et al., 2011).
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
99
DDT and HCH are synthetic organochlorine compounds (OCs) previously used widely in
public health programmes and as agricultural pesticides. Although the use of DDT and HCH
is currently banned or restricted in many parts of the world, their inherent environmental
characteristics, illegal use and poor management of stockpiles of DDT and HCH result in their
occurrence in the environment (Singh and Lal, 2009; Ntow and Botwe, 2011). Furthermore,
DDT is still permitted for use in malaria control in malaria endemic tropical developing
countries (Ntow and Botwe, 2011). Thus, continuous monitoring and assessment of these
persistent organochlorine pollutants in the environment remain relevant.
The occurrence of PAHs in the environment typically relates to the release of crude oil and
refined petroleum products (referred to as petrogenic sources) or combustion of organic
matter and fossil fuel (referred to as pyrogenic sources) (Wang et al., 2001; Yunker et al.,
2002; De Luca et al., 2004; Neff et al., 2005; Nyarko et al., 2011). PAHs which contain two or
three fused benzene rings are classified as low molecular weight PAHs (LPAHs), while those
having four to six fused benzene rings are classified as high molecular weight PAHs
(HPAHs). Although PAHs commonly occur as a mixture of several hundreds of related
compounds in the environment (Neff et al., 2005), the sixteen PAH compounds (PAH16)
designated as priority PAHs by the United States Environmental Protection Agency (USEPA)
have become prime targets in many PAH contamination and bioremediation studies (Wang et
al 2001; De Luca et al., 2004; King et al., 2004).
As the ultimate repository of chemical pollutants released into aquatic ecosystems (Burton,
2002; Birch and Hutson, 2009; Hu et al., 2009; Lin et al., 2009; Smith et al., 2009), sediments
usually attain high levels of chemical pollutants and pose hazards to benthic organisms as well
as other organisms in the aquatic food chain (Hong et al., 1995). Thus, there have been
growing efforts to remediate contaminated sediments, commonly by dredging (Burton, 2002).
Coastal marine harbours, particularly those associated with industrial and urban centres, are of
major concern as such harbours serve as receptacles for a variety of pollutants released from
industrial, urban, shipping, fishing and other anthropogenic activities (Simpson et al., 1996;
Mestres et al., 2010; Lin et al., 2009; Smith et al., 2009). Furthermore, the low-energy
hydrodynamics in harbours (Mestres et al., 2010) enhance the accumulation of sediment-
associated pollutants. Thus, Lin et al. (2009) and Simpson et al. (1996) reported high levels of
DDT and PAH, respectively, in harbour sediments. Dredging with subsequent disposal of
contaminated harbour sediments also pose a threat to the receiving ecosystem as contaminated
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
100
sediments are potential sources of pollutants to biota (Hong et al., 1995; Burton, 2002).
Investigation of sediment contamination and associated ecological risks is, therefore, a
priority for environmental regulators (Burton, 2002; Birch and Hutson, 2009). Prior to
undertaking remedial actions, screening-level ecotoxicological risk assessments on sediments
are conducted to identify: (i) pollutants of potential ecotoxicological concern, (ii) priority
areas, and (iii) the potential to cause adverse ecological effects (Burton, 2002; Long et al.,
2006; Birch and Hutson, 2009).
The coastal marine Tema Harbour, located along the Gulf of Guinea at Tema in Ghana, is an
international harbour with considerable shipping and fishing activity. The construction of the
Tema Harbour in 1960 coincided with the commencement of industrialisation in Ghana,
specifically in Tema, which has since been the major industrial city of Ghana. Major
industrial activities in Tema include alumina smelting, crude oil refining, paint, steel and
cement production. Thus, the Tema Harbour has been subjected to industrial, shipping, fishing
and other anthropogenic activities for nearly six decades. Notable incidents at the Tema
Harbour during the past decade include two major oil spills with subsequent clean-up and a
fire explosion at the shipyard, which destroyed oil pipeline installations of the Tema Oil
Refinery (TOR) at the harbour (Ghana New Agency, 29 March 2005). The fire and oil spill
incidents at the Tema Harbour, shipping and fishing activities, as well as discharges from the
surrounding industries might have caused release of PAHs and other pollutants into the
harbour. Thus, assessment of sediment contamination and associated ecotoxicological risk is
indispensable, as follow-up of a preliminary study conducted in 2008 suggesting sediment
PAH pollution in Tema Harbour (Gorleku et al., 2014). The aim of the present study was to
assess the levels, spatial distributions and sources of DDTs, HCHs and PAH16 in surface
sediments from the Tema Harbour. In addition, the ecotoxicological risks were evaluated
using biological effect-based numerical sediment quality guidelines and total toxicity
equivalence approaches.
4.2. Materials and methods
4.2.1. Sediment sampling
Surface sediment samples were collected with a stainless steel Ekman grab (3.5 L) from 21
locations in the Tema Harbour in January 2014. The monitoring stations were spread over the
different compartments of the Tema Harbour: fourteen in the Main Harbour excluding rocky
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
101
areas, two each in the Inner Fishing Harbour and the Outer Fishing Harbour; and three in the
Canoe Basin (S15-S17) (Fig. 3.1). At each station, three grab samples were collected and the
surficial sediments scooped with a stainless steel spoon from the upper 0-2 cm layer, which is
considered representative of recently deposited sediments (Phillips, 2007). Each composite
sediment sample was mixed and then split into two: one for analysis of grain size and the
other for analyses of organic contaminants (DDTs, HCHs and PAHs), total organic carbon
(TOC) and total nitrogen (TN). The sediment samples were finally taken into Rilsan® bags,
stored in an ice-cooled box on the field and later transported to the Department of Marine and
Fisheries Sciences laboratory of the University of Ghana, about 60 km away. In the
laboratory, the sediment samples were stored in a freezer at -20 oC till analysis within 4
weeks. The redox potential (Eh) of the bottom water at each monitoring station was measured
in situ by using a Hanna multi-parameter probe (HI 9829, Hanna Instruments, USA), taking
measurements after the Eh values had stabilised (typically within 2 min).
4.2.2. Sediment analyses
The silt-clay (<63 µm) and sand (63-2000 µm) fractions in the sediment samples were
determined on wet samples by the wet sieving method following Wang et al. (2001). Analyses
of DDTs, HCHs, PAHs, TOC and TN were performed on freeze-dried and homogenised bulk
sediment samples. TOC and TN contents were determined following the Walkley-Black wet
oxidation (Schumacher, 2002) and the Kjeldahl (Sáez-Plaza et al., 2013) method, respectively,
after decarbonisation with excess 1 M HCl. Analysis of DDTs, HCHs and PAHs was by
Soxhlet-extraction following Wang et al. (2001) and Fung et al. (2005), with some
modifications. Briefly, about 10 g of dry homogenised sediment samples were spiked with
100 µl of 1 µg/mL standard solutions of acenaphthylene-d8, acenaphthene-d10, fluorene-d10 (as
internal standards for PAH) and PCB-204 and PCB-230 (as internal standards for DDTs and
HCHs) before Soxhlet-extraction with 150 mL of dichloromethane/acetone (1:1 v/v) mixture
for 16 h. Prior to the extraction, the sediment samples were mixed with 5 g of anhydrous
granular sodium sulphate previously heated at 400 oC for 4 h and 2 g of activated copper
powder to remove sulphur. Using a rotary evaporator, the extracts were then slowly
evaporated to near dryness and the residue re-dissolved in 2 mL n-hexane for clean-up.
Clean-up of the extracts was carried out using glass chromatographic columns (20 x 1.0 cm)
packed with 8 g of Davisil Grade 923 silica gel from Sigma Aldrich, pre-heated at 130 oC for
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
102
16 h. The chromatographic columns were first conditioned by eluting successively with 15
mL of dichloromethane and 20 mL of n-hexane, before the extracts were applied to the
columns and eluted successively with 15 mL of n-hexane and 20 mL of n-
hexane/dichloromethane (80:20) mixture. The eluates were collected, concentrated to near
dryness by a pure stream of N2 gas and finally reconstituted in 1 mL n-hexane for analysis of
DDTs, HCHs and PAH16. The PAH16 were analysed by using a Perkin Elmer AutoSystem gas
chromatograph with flame ionisation detector (GC-FID, Agilent 6890 Series GC System),
while DDTs and HCHs were analysed by using the same GC with a 63
Ni electron capture
detector (GC-ECD). Identities of PAHs, DDTs and HCHs were confirmed using a GC with
mass selective detector (GC-MSD).
4.2.3. Quality assurance and control
All sediment samples were analysed in triplicates. Chemicals, solvents and reagents used in
the extraction were of HPLC grade. All containers used were either new or thoroughly
cleaned. Prior to sample analysis, the GC instrument was calibrated with mixed standards for
DDTs and HCHs (EPA608-Pest.Mix 1, Sigma-Aldrich), and PAH16 (16 Priority EPA PAHs,
Campro Scientific GmbH, Germany). Routine analyses of procedural blanks, reagent blanks,
spiked blanks, sample replicates and samples of a Standard Reference Material for sediments
(SRM 1944) from the National Institute of Standards and Technology (NIST) were conducted
to assess contamination and recovery of analytes. The target organic contaminants were not
detected in both procedural and reagent blanks. Recoveries ranged between 81 and 98% for
PAHs and between 78 and 94% for DDTs and HCHs, with relative standard deviations (RSD)
below 5 % (see Table 4.1). Reported PAH, DDT and HCH concentrations were not corrected
for recoveries.
4.2.4. Data treatment
Two-tailed Pearson's product-moment correlations were conducted to determine associations
between the measured sediment parameters using the Statistical Package for Social Sciences
(SPSS version 16.0) software. Descriptive statistics (mean and standard deviations) were
performed in Windows Excel (2007) at the 95 % confidence interval. One-way analysis of
variance (ANOVA) with multiple comparisons (Holm-Sidak and Kruskal-Wallis) tests were
performed to assess significant differences in the spatial distribution of measured sediment
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
103
Table 4.1 Measured (n =3) and certified concentrations of target OC and PAH
compounds in standard reference material (SRM 1944)
RSD = relative standard deviation
*Provided as reference concentration instead of certified concentration
Compound Measured
value
Certified
value
Recovery
(%)
RSD
(%)
OCs (µg.kg-1
d.w)
p,p'-DDT 109 ± 4 119 ± 11 92 3.3
p,p'-DDE 81 ± 4 86 ± 12* 94 4.8
p,p'-DDD 84 ± 2 108 ± 16* 78 2.0
α-HCH 1.9 ± 0.1 2.0 ± 0.3* 94 4.3
PAHs (mg.kg-1
d.w)
Naphthalene 1.34 ± 0.04 1.65 ± 0.31 81 3.0
Phenanthrene 5.11 ± 0.06 5.27 ± 0.22 97 1.1
Anthracene 1.58 ± 0.04 1.77 ± 0.33 89 2.3
Fluoranthene 8.72 ± 0.10 8.92 ± 0.32 98 1.1
Pyrene 9.44 ± 0.11 9.70 ± 0.42 97 1.2
Benz[a]anthracene 4.51 ± 0.07 4.72 ± 0.11 96 1.6
Chrysene 4.53 ± 0.10 4.86 ± 0.10 93 2.1
Benzo[b]fluoranthene 3.60 ± 0.04 3.87 ± 0.42 93 1.1
Benzo[k]fluoranthene 2.17 ± 0.04 2.30 ± 0.20 94 1.7
Benzo[a]pyrene 4.10 ± 0.05 4.30 ± 0.13 95 1.3
Benzo[ghi]perylene 2.68 ± 0.03 2.84 ± 0.10 94 1.1
Indeno[1,2,3-
cd]pyrene 2.58 ± 0.04 2.78 ± 0.10 93 1.6
Dibenz[a,h]anthracene 0.39 ± 0.01 0.424 ± 0.069 92 2.6
Fluorene 0.80 ± 0.02 0.85 ± 0.03* 94 1.9
Acenaphthene 0.52 ± 0.03 0.57 ± 0.03* 92 4.8
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
104
parameters using SigmaPlot software (version 11.0). The distributions of ΣDDTs, ΣHCHs,
ΣPAHs and mERMQ in the harbour were mapped using ArcGIS software (version 10.2.2).
4.3. Results
4.3.1. Sediment physicochemical characteristics
The measured physicochemical characteristics of the Tema Harbour sediments are presented
in Table 4.2. The bottom water in the harbour was anoxic with Eh values ranging from -50 to -
420 mV. The grain size composition of the harbour sediments revealed a predominance of the
sandy (63-2000 µm) fraction with the mean silt-clay (<63 µm) fraction varying between 21
and 39 %. Sediments from the north-eastern corner (stations S1-S4, S13 and S14) and central
parts of the Main Harbour had relatively higher silt-clay contents. The TOC content of the
sediments ranged from 2.2 to 7.2 %, showing a significant variation (p = 0.027, ANOVA) in
spatial distribution but without any clear trend. Stations with relatively high TOC content
include S2, S7, S12, the Canoe Basin (S15-S17) and the Inner Fishing Harbour (S18 and S19).
There was, however, no significant correlation (r = -0.004, p > 0.05) between the TOC and
silt-clay contents. The mean sediment TN content varied from 0.8 to 1.4 % among the
monitoring stations, but no significant variation (p = 0.782, ANOVA) was observed in the
distribution of TN across the monitoring stations. There was also a poor correlation (r = -0.18,
p > 0.05) between the silt-clay and TN contents. The mean TOC contents were 2-9 times
higher than the mean TN contents, with a poor correlation (r = -0.144, p > 0.05) between the
TOC and TN contents.
4.3.2. Levels and distribution of DDTs and HCHs in the Tema Harbour sediments
A widespread occurrence of DDTs (p,p'-DDT, p,p'-DDE and p,p'-DDD) and HCHs (α-HCH,
β-HCH, γ-HCH and δ-HCH) was observed in the harbour sediments. The mean concentration
ranges of p,p'-DDT, p,p'-DDE and p,p'-DDD were 1.6-3.5, 0.8-2.0 and 2.8-7.5 µg.kg-1
d.w,
respectively (Table 4.2). Overall, the mean concentrations of ΣDDTs (i.e., p,p'-DDT + p,p'-
DDE + p,p'-DDD) ranged from 6.0 to 12.8 µg.kg-1
d.w, with significant differences in the
spatial distribution (one way ANOVA, p < 0.001): the north-easternmost part of the harbour
being most contaminated (Fig. 4.1a). The ΣDDTs concentrations highly correlated with the
concentrations of p,p'-DDT (r = 0.77, p < 0.01) and p,p'-DDD (r = 0.96, p < 0.01), and to a
lesser extent, with p,p'-DDE (r = 0.49, p < 0.05). A significant correlation was observed
between the p,p'-DDT and p,p'-DDD concentrations (r = 0.62, p < 0.01), but both p,p'-DDT (r
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
105
= 0.24, p > 0.05) and p,p'-DDD (r = 0.33, p > 0.05) exhibited poor correlations with p,p'-
DDE. Both ΣDDTs (r = 0.58, p < 0.01) and p,p'-DDD (r = 0.54, p < 0.05) exhibited
significant correlations with the silt-clay contents, but poor correlations with both TOC and
TN contents in the sediments. Moreover, the concentrations of p,p'-DDT and p,p'-DDE
exhibited poor correlations with the silt-clay, TOC and TN contents in the sediments.
Like DDTs, HCHs were ubiquitous in the harbour sediments. The mean concentration ranges
of α-HCH, β-HCH, γ-HCH and δ-HCH were 0.6-2.6, 0.4-5.2, 1.1-5.8 and 0.2-1.8 µg.kg-1
d.w,
respectively (Table 4.2). One way ANOVA revealed significant differences (p < 0.001) in the
distribution of γ-HCH across the monitoring stations: relatively higher levels were found in
the Inner Fishing Harbour, stations S15 (in the Canoe Basin) and S4 and S14 (in the Main
Harbour). Overall, the mean concentrations of ΣHCHs (i.e., α-HCH + β-HCH + γ-HCH + δ-
HCH) varied from 2.8 to 13.6 µg.kg-1
d.w. The spatial distribution pattern shows the north-
eastern part of the harbour being most contaminated (Fig. 4.1b). Good correlations were found
between the concentrations of ΣHCHs and α-HCH (r = 0.53, p < 0.05), β-HCH (r = 0.88, p <
0.01), γ-HCH (r = 0.86, p < 0.01) and δ-HCH (r = 0.60, p < 0.01). Among the HCH isomers,
significant correlations were observed between α-HCH and γ-HCH (r = 0.43, p < 0.05), β-
HCH and γ-HCH (r = 0.61, p < 0.01), and β-HCH and δ-HCH (r = 0.69, p < 0.01), while poor
correlations were observed between α-HCH and β-HCH (r = 0.23, p > 0.05), α-HCH and δ-
HCH (r = 0.09, p > 0.05), and γ-HCH and δ-HCH (r = 0.31, p > 0.05). No significant
correlations were observed between the HCHs and concentrations of DDTs, the silt-clay
content or the TOC and TN content.
4.3.3. Levels and distribution of PAHs in the Tema Harbour sediments
The USEPA 16 priority PAHs (PAH16) namely naphthalene (Nap), acenaphthylene (Acy),
acenaphthene (Ace), fluorene (Flu), phenanthrene (Phe), anthracene (Ant), fluoranthene (Fla),
pyrene (Pyr), benzo[a]anthracene (BaA), chrysene (Chr), benzo[b]fluoranthene (BbF),
benzo[k]fluoranthene (BkF); benzo[a]pyrene (BaP), benzo[g,h,i]perylene (BghiP),
indeno[1,2,3-cd]pyrene (IP) and dibenz[a,h]anthracene (DahA) were frequently detected in
the harbour sediment samples and their mean concentrations are presented in Table 4.3.
Generally, phenanthrene recorded the highest mean levels (510-750 µg.kg-1
d.w; mean = 610
µg.kg-1
d.w), followed by acenaphthylene (410-660 µg.kg-1
d.w; mean = 500 µg.kg-1
d.w) and
pyrene (330-750 µg.kg-1
d.w; mean = 456 µg.kg-1
d.w). Concentrations of summed PAHs
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
106
(ΣPAH16) ranged from 2750-5130 µg.kg-1
d.w with a mean of 3700 µg.kg-1
d.w, with
significant variations in the distribution of PAH16 across the monitoring stations (Kruskal-
Wallis one way ANOVA on ranks, p < 0.001). The PAH distribution pattern shows that
sediments in the Main Harbour are less contaminated by ΣPAH16 compared to those of the
Fishing Harbour (see Fig. 4.1c).
4.4. Discussion
4.4.1. Physicochemical characteristics of the Tema Harbour sediments
Sediment attributes such as silt-clay and organic carbon contents influence organic pollutant
uptake by sediments (Wang et al., 2001; Ahrens and Depree, 2004; De Luca et al., 2004; King
et al., 2004; Wang et al., 2006; Lin et al., 2009). Furthermore, the redox conditions of
sediments play a role in the biodegradation of organic matter (Caille et al., 2003) and thereby,
the accumulation of organic matter in sediments. The results of the grain-size analysis showed
that the Tema Harbour sediments were predominantly sandy, with the silt-clay fraction
constituting 21-39 % (Table 4.2). This predominance of sand may be due to its large inputs by
ocean water currents and movements of ships (Kelderman, 2012).
The TOC/TN ratios in the sediments, which ranged from 2.4 to 9.0 (Table 4.2), indicate a
predominance of autochthonous organic matter in the harbour sediments, as organic matter of
marine (autochthonous) sources is characterised by TOC/TN ratios ≤ 8.0 (Burdige, 2007; Tesi
et al., 2007). This predominance of autochthonous organic matter may be linked to the fact
that the harbour hardly receives direct riverine inflows, which could have introduced large
quantities of terrestrial (allochthonous) organic matter into the harbour. There was lack of a
good correlation between the silt-clay fractions and TOC content, possibly due to localised
anthropogenic inputs of organic matter into the harbour, which will vary across the
monitoring stations. Organic loading coupled with poor water circulation may have
contributed to the prevailing anoxic condition in the harbour. Such anoxic conditions have the
potential to retard the microbial decomposition of organic matter, as anaerobic biodegradation
rates of organic matter (methane production or sulphate reduction) in marine sediments are
usually slower than aerobic biodegradation (Caille et al., 2003). The anoxic condition at the
inner station in the Canoe Basin (S15) is of concern as the Eh value was below the minimum
established value of -300 mV for natural sediments (Ye et al., 2013).
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
107
4.4.2. Effect of silt-clay and TOC content on the DDTs, HCHs and PAHs distribution
This baseline study shows that DDTs (p,p'-DDT, p,p'-DDE and p,p'-DDD), HCHs (α-HCH, β-
HCH, γ-HCH and δ-HCH) and the USEPA 16 priority PAHs (PAH16) were ubiquitous in the
Tema Harbour sediments. Different distribution patterns of ΣDDTs, ΣHCHs and ΣPAHs in
sediments were observed across the monitoring sites: the most north-eastern part of the
harbour is relatively more contaminated by ΣDDTs (Fig. 4.1a), ΣHCHs (Fig. 4.1b) and
ΣPAHs (Fig. 4.1c). The strong affinity of fine grain sediments and organic carbon for organic
pollutants (Hu et al., 2009; Lin et al., 2009) has often resulted in significant correlations
(Maruya et al., 1996; Wang et al 2001; Yang et al., 2005) and consequently, the need to
normalise organic pollutant concentrations using the TOC content is required for comparison
(Birch and Hutson, 2009; Lin et al., 2009). In this study, only ΣDDTs, p,p'-DDD and
naphthalene (Nap) exhibited moderate, but significant, correlations with the silt-clay contents
of the sediments, while only benzo[k]fluoranthene (BkF) exhibited a moderate, but
significant, correlation with TOC.
These poor correlations may be due to various reasons. According to Ahrens et al. (2004), the
presumption that organic pollutants and/or TOC preferentially partition to the fine sediment
fractions is not always holding and therefore, should not be generalised for all sediments.
PAH, for example, has been shown to preferentially partition to the coarse grains of sediments
(Wang et al., 2001). Moreover, in the Tema Harbour, different anthropogenic activities are
carried out at different areas, which may largely influence the spatial distributions of the
pollutants. Thus, stations S1 and S2 are close to the dry docks with vessel painting and
sandblasting activities; station S4 (Oil Berth) is close to the point of discharge of crude oil and
refined petroleum products; stations S10 and S11 are points of container operation in the
harbour; fuel storage and fuelling of industrial fishing vessels is carried out in the Outer
Fishing Harbour (S20 and S21); while the Canoe Basin (S15-S17) is dedicated to artisanal
fishing operations. As mentioned earlier, localised anthropogenic inputs of organic matter into
the harbour will have contributed to the observed poor correlations between sediment
pollutants and TOC and/or silt-clay contents. For example, effluent discharges from nearby
food canneries into the Main Harbour near the Shekete area (stations S7 and S12) could be
important localised sources of organic matter in the Main Harbour. The Canoe Basin (S15-
S17) and the Inner Fishing Harbour (S18 and S19) are also exposed to high loadings of
organic waste from the operations of the fisher folk.
Table 4.2 Physicochemical parameters and mean DDTs and HCHs concentrations (µg.kg-1 d.w) in Tema Harbour sediments and SQGs
aSediment Quality Guidelines (SQGs): ERL and ERM (µg.kg
-1) from Long et al. (2006); ERL = effective range low; ERM = effective range median.
Monitoring
station
Water
depth
(m)
Eh
(mV)
Silt-
clay
(%)
TOC
(%)
TN
(%) TOC/TN
p,p'-
DDT
p,p'-
DDE
p,p'-
DDD ΣDDTs
α-
HCH β-HCH γ-HCH δ-HCH ΣHCHs
S1 9.5 -100 37.2 3.8 1.0 3.8 2.5 1.5 4.3 8.3 1.0 0.5 1.4 0.7 3.6
S2 7 -120 31.4 7.2 0.8 9.0 2.6 1.9 5.8 10.3 0.6 0.6 1.1 0.5 2.8
S3 9 -100 33.6 4.8 0.8 6.0 3.2 1.3 5.3 9.7 2.1 0.9 2.9 0.4 6.1
S4 8 -80 38.5 3.9 0.8 4.9 2.8 2.0 3.1 7.9 2.3 1.6 5.5 0.4 9.8
S5 8 -70 34.7 2.7 0.9 3.0 2.5 1.2 3.3 7.0 2.1 1.6 3.3 0.2 7.1
S6 8 -90 34.6 3.8 1.0 3.8 2.3 0.9 2.8 6.0 0.9 0.6 1.7 0.3 3.4
S7 8 -90 28.2 5.4 0.8 6.8 3.2 1.3 4.2 8.7 1.2 1.4 4.1 0.2 6.7
S8 8.5 -90 25.1 2.2 0.8 2.2 1.6 1.2 3.7 6.4 2.0 1.5 3.1 1.5 8.2
S9 9 -70 29.8 4.7 0.8 5.9 2.9 1.4 4.5 8.7 1.2 0.5 4.4 0.2 6.2
S10 10 -80 27.3 2.9 1.2 2.4 3.2 1.6 5.1 9.9 1.2 0.4 3.5 0.5 5.6
S11 9 -80 24.5 2.9 1.1 2.6 3.0 0.8 4.2 8.1 0.6 0.7 2.0 0.5 3.7
S12 9 -50 30.6 5.5 1.0 5.5 3.3 1.5 5.4 10.1 0.7 1.0 2.1 0.2 3.9
S13 8 -80 32.6 4.8 1.0 4.8 2.4 1.1 4.4 8.0 0.8 1.5 4.4 1.4 8.0
S14 10 -90 23.7 3.8 0.8 4.8 2.1 1.4 5.5 8.0 1.8 1.6 5.3 1.4 10.2
S15 3.5 -360 25.6 5.8 1.4 4.1 3.5 1.9 7.5 12.8 1.3 1.5 5.1 0.4 8.2
S16 4 -240 24.8 4.5 0.8 5.6 3.4 1.6 6.8 11.8 1.4 1.6 3.1 0.5 6.7
S17 5 -160 22.2 6.6 0.9 7.3 3.2 1.5 5.7 10.4 1.5 0.5 3.8 0.6 6.5
S18 8 120 28.8 6.7 1.0 6.7 2.7 1.2 4.9 8.8 1.1 5.2 5.8 1.4 13.6
S19 8 110 25.2 5.3 0.8 6.6 2.5 1.9 3.8 8.2 1.5 4.6 5.0 1.8 12.7
S20 8 -110 24.6 3.9 0.9 4.3 2.3 1.6 3.5 7.4 1.9 3.5 4.1 1.7 11.2
S21 8 -100 21.4 2.9 1.0 2.9 2.4 1.4 3.3 7.2 2.6 2.9 4.4 1.5 11.5
Mean - - 28.8 4.4 0.9 - 2.7 1.4 4.6 8.8 1.4 1.6 3.6 0.8 7.4 aERL
1 2.2 2 1.58 - - 0.32 - -
aERM
7 27 20 46.1 - - 1 - -
Table 4.3 Mean concentrations (µg.kg-1
d.w, n = 3) of USEPA 16 priority PAHs (PAH16) in Tema Harbour surface sediments, SQGs and TEFs
Low Molecular Weight PAHs (LPAHs) High Molecular Weight PAHs (HPAHs)
Sample
station Nap Acy Ace Fle Phe Ant Fla Pyr BaA Chr BbF BkF BaP BghiP IP DahA ΣLPAH16
S1 270 420 270 150 530 26 310 340 60 270 130 64 160 50 35 13 3010
S2 380 410 240 170 550 28 230 350 100 360 150 53 100 14 38 19 3200
S3 350 420 260 160 570 35 350 350 100 430 100 84 140 50 36 27 3470
S4 390 590 350 350 750 37 440 650 170 520 160 64 160 120 150 26 4900
S5 330 490 240 150 550 26 240 350 100 320 140 52 160 17 50 24 3200
S6 360 410 230 150 530 33 320 340 70 300 130 69 160 16 19 33 3170
S7 260 410 150 140 530 29 230 340 60 220 120 61 150 14 15 18 2750
S8 250 420 250 160 530 30 210 330 100 310 170 46 140 40 27 30 3040
S9 340 450 260 170 550 27 230 340 70 270 140 56 110 40 50 21 3100
S10 290 440 230 140 590 33 240 400 100 300 130 44 130 20 12 43 3100
S11 260 480 240 140 540 28 230 350 100 280 160 82 150 32 32 29 3120
S12 260 470 250 150 560 30 230 350 100 290 150 55 110 13 40 22 3100
S13 250 500 150 140 510 24 230 340 60 240 110 43 150 26 28 23 2830
S14 350 470 250 150 560 24 330 350 90 370 130 43 140 28 15 42 3340
S15 490 660 380 190 750 46 440 750 170 580 130 43 170 200 130 28 5130
S16 440 630 330 350 740 38 430 730 150 550 110 51 140 120 130 34 4980
S17 460 620 340 340 730 41 420 700 160 530 120 40 160 190 120 20 5000
S18 360 500 250 140 560 30 330 340 80 380 110 67 150 22 22 34 3370
S19 370 580 290 360 750 32 430 660 160 510 130 53 150 130 140 21 4750
S20 360 550 270 360 730 40 430 600 160 500 150 49 170 110 130 29 4610
S21 330 600 170 340 750 32 440 620 160 470 130 40 150 120 140 18 4490
Mean 340 500 260 210 610 32 320 460 110 380 130 55 150 65 64 26 3700
ERL 160 44 16 19 240 85.3 600 665 261 384 - - 430 - - 63.4 4022
ERM 2100 640 500 540 1500 110
0 5100 2600 1600 2800 - - 1600 - - 260 44792
TEF 0.00
1 0.001 0.001 0.001
0.00
1 0.01 0.001 0.001 0.1 0.01 0.1 0.1 1 0.01 0.1 5 (1*) -
ERL and ERM values (µg.kg-1
) are from Burton (2002); TEF = toxic equivalency factor (Nisbet and LaGoy, 1992)
* USEPA value (https://fortress.wa.gov/ecy/clarc/FocusSheets/tef.pdf)
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
110
mERMQ (µg/kg)
0.5 – 0.7
0.7 – 0.9
0.9 – 1.1
1.1 – 1.3
1.3 – 1.4
1.4 – 1.6
1.6 – 1.7
1.7 – 1.8
1.8 – 1.9
1.9 – 2
ΣPAHs (µg/kg)
2750 – 2920
2920 – 3120
3120 – 3340
3340 – 3590
3590 – 3870
3870 – 4180
4180 – 4470
4470 – 4710
4710 – 4930
4930 – 5130
ΣDDTs (µg/kg)
6 – 6.5
6.5 – 7
7 – 7.6
7.6 – 8.1
8.1 – 8.8
8.8 – 9.5
9.5 – 10
10 – 11
11 – 12
12 – 13
ΣHCHs (µg/kg)
2.8 – 3.9
3.9 – 5.1
5.1 – 6.3
6.3 – 7.7
7.7 – 9.2
9.2 – 11
11 – 12
12 – 14
TEQ (mg/kg)
0.15 – 0.15
0.15 – 0.16
0.16 – 0.17
0.17 – 0.18
0.18 – 0.19
0.19 – 0.20
0.20 – 0.20
0.20 – 0.21
0.21 – 0.22
0.22 – 0.23
Fig. 4.1 Distribution patterns of (a) ΣDDTs, (b) ΣHCHs, (c) ΣPAHs, (d) mERMQ and
(e) TEQ in Tema Harbour sediments
a
c
c d
a
e
a b
d
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
111
4.4.3. Sources of DDTs and HCHs in the Tema Harbour sediments
Both DDT and HCH are pesticides of anthropogenic origin: DDT is commercially produced
as technical DDT and HCH as technical HCH and lindane. Although the Tema Harbour does
not receive direct riverine inflows, it may be impacted by inland and coastal agricultural
activities via alongshore water and sediment transport, as well as by atmospheric deposition
and surface runoff (Botwe et al., 2012). As the Tema Harbour serves as the main sea port for
imports, it is also possible that accidental pesticides spills may have occurred in the past, and
have contributed to DDT and HCH contamination in the harbour sediments. Isolated cases of
DDT use by Ghanaian fisher folks have also been reported
(http://www.graphic.com.gh/news/general-news/danger-watch-the-fish-you-buy.html). There
is, however, no information on how widespread this practice has been or on the quantities of
DDT used. DDT is a key constituent in antifouling paints widely used in boat maintenance.
This has earlier been identified as a major source of DDT contamination in fishing harbours
(Lin et al., 2009) and coastal marine sediments (Hu et al., 2009; Yu et al., 2011). However,
the use of these DDT-based antifouling paints on fishing vessels in Ghana has not been
reported.
DDT and lindane are included in the list of persistent organic pollutants (POPs) targeted for
global elimination under the Stockholm Convention, which Ghana has ratified and both
pollutants were officially banned from use in Ghana in 1985 and 2002, respectively (Ntow
and Botwe 2011). Prior to their ban in Ghana, they were largely used as pesticides in
agriculture, e.g. lindane predominantly in cocoa plantations. Since their ban, residues of DDT
and lindane have been measured in water, sediment, crops and biota in Ghana (Ntow and
Botwe 2011), owing to their persistence, illegal use and existence of stockpiles (Singh and Lal
2009; Ntow and Botwe 2011). For example, in 2008, about 71,000 kg of banned pesticides
were detected at a facility belonging to the Ghana Cocoa Board (Daily Graphic newspaper, 8
April 2008).
DDT and its degradation products DDE and DDD are all persistent in the environment with
similar physical and chemical characteristics (WHO, 1989). Due to the low proportions of
DDE and DDD in technical DDT, DDT/DDD and DDT/(DDE + DDD) ratios < 1.0 are
generally indicative of past use of DDT, whereas ratios > 1.0 indicate current use (Li et al.,
2014). The DDT/DDD and DDT/(DDE + DDD) ratios in all analysed Tema Harbour
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
112
sediments were < 1.0 (Table 4.4), indicating that DDT contamination in the harbour is likely
the result of DDT use in the distant past. A significant positive correlation (p < 0.01) was
observed between p,p'-DDT and p,p'-DDD, which suggests some contribution of these
components from influx of weathered sediment-bound DDT. Among the DDTs,
disproportionately higher levels of p,p'-DDD (39-61 % of the measured ΣDDTs
concentrations) were found in sediments at the monitoring stations (see Table 4.4), indicating
substantial transformation of p,p'-DDT to p,p'-DDD in the harbour sediments. The higher
levels of p,p'-DDD relative to those of p,p'-DDE can be attributed to the discriminatory
degradation of p,p'-DDT to p,p'-DDD in anoxic sediments (Lin et al., 2009).
The α-HCH/γ-HCH ratio in sediments allows delineation of the sources of HCH as technical
HCH (predominantly constituted by α-HCH) or lindane (>99 % γ-HCH). Technical HCH has
α-HCH/γ-HCH ratios ranging between 3 and 7, whereas those of lindane are < 1.0 or close to
1.0 (Willett et al., 1998). The α-HCH/γ-HCH ratios in sediments from all the monitoring
stations were < 1.0 (Table 4.4), pointing to the use of lindane as the major source of HCH
contamination in the harbour. The γ-HCH isomer accounted for 37-71 % of the ΣHCHs
concentrations in the sediments. In anaerobic sediments, as in those investigated, the
conversion of γ-HCH to other HCH isomers can be an extremely slow process (Walker et al.,
1999), which could have resulted in the predominance of γ-HCH in the anaerobic harbour
sediments.
4.4.4. Sources of PAHs in the harbour sediments
Most of the PAHs exhibited significant correlations, possibly because they derive from
common sources. Various anthropogenic activities within the harbour (e.g. crude oil spills
during bunkering and fuelling of vessels, fuel leakages, ballast and bilge water discharges
from ships, ship painting at the dry-dock, and vehicular emissions) as well as discharges and
emissions from various industrial activities that characterise the city of Tema (e.g. oil refinery,
aluminium smelting, cement production, pain manufacturing, and fish processing) may have
contributed to the PAH contamination in the sediments (Yunker et al., 2000; Yunker et al.,
2002; Neff et al., 2005). Discharges of oil into the harbour from the aforementioned sources
may occur on a daily basis. Moreover, as mentioned, there have been two major incidents of
oil spill in the Tema Harbour, in 2005 and 2007. A study conducted shortly after these
incidents in 2008 reported mean ΣPAHs concentrations in the range of 28,600-190,000 µg.kg-
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
113
1 w.w (Gorleku et al. 2014). Although differences in concentration units do not allow for
comparison, we infer that the mean ΣPAHs concentrations in this study (2,750-5,130 µg.kg-1
d.w) conducted in 2014 are much lower than the levels reported by Gorleku et al. (2014).
Thus, this study indicates that there has been a considerable reduction in PAH contamination
in the Tema Harbour during the period 2008-2014.
To characterise the dominant sources of PAH contamination in the Tema Harbour sediments,
ΣLPAH/ΣHPAH and three PAH isomeric ratios viz. anthracene/[anthracene + phenanthrene],
fluoranthene/[fluoranthene + pyrene] and benzo(a)anthracene/[benzo(a)anthracene +
chrysene] were evaluated (Table 4.4). Pyrogenic sources are mainly related to the combustion
of organic matter and show enrichment in the high-molecular weight PAH (HPAH)
components, whereas petrogenic sources relate to spillages of petroleum/crude oil and refined
petroleum products and exhibit enrichment in the low-molecular weight PAH (LPAH)
components (Yunker et al., 2000; Yunker et al., 2002; Neff et al., 2005). The ΣLPAH/ΣHPAH
ratios in the sediments at the monitoring stations were close to 1.0, suggesting similar
contributions of PAHs from both petrogenic and pyrogenic sources. The
anthracene/[anthracene + phenanthrene] and fluoranthene/[fluoranthene + pyrene] ratios
indicate PAH contamination in the harbour derived mainly from petrogenic sources, whereas
the benzo(a)anthracene/[benzo(a)anthracene + chrysene] ratios suggest rather mixed
petrogenic and pyrogenic sources. Thus, the use of different PAHs source diagnostic ratios
has not yielded overall consistent results for the Tema Harbour sediments investigated.
Table 4.4 Source diagnostic DDT, HCH and PAH ratios in Tema Harbour sediments
Monitoring
station
DDT/
DDE
DDT/
DDD
DDE/
DDD
DDT/
(DDE+DDD)
ΣLPAHs/
ΣHPAHs
Ant/
(Ant + Phe)
Fla/
(Fla + Pyr)
BaA/
(BaA + Chr)
α-HCH/
γ-HCH
β-HCH/
γ-HCH
δ-HCH/
γ-HCH
S1 1.6 0.6 0.4 0.4 1.2 0.05 0.5 0.18 0.7 0.4 0.5
S2 1.3 0.4 0.3 0.3 1.3 0.05 0.4 0.22 0.6 0.6 0.5
S3 2.5 0.6 0.2 0.5 1.1 0.06 0.5 0.19 0.8 0.3 0.1
S4 1.5 0.9 0.6 0.6 1.0 0.05 0.4 0.25 0.4 0.3 0.1
S5 2.1 0.8 0.4 0.6 1.2 0.05 0.4 0.24 0.6 0.5 0.1
S6 2.5 0.8 0.3 0.6 1.2 0.06 0.5 0.19 0.6 0.3 0.1
S7 2.4 0.8 0.3 0.6 1.2 0.05 0.4 0.21 0.3 0.3 0.05
S8 1.4 0.4 0.3 0.3 1.2 0.05 0.4 0.24 0.6 0.5 0.5
S9 2.1 0.6 0.3 0.5 1.4 0.05 0.4 0.21 0.3 0.1 0.5
S10 2.1 0.6 0.3 0.5 1.2 0.05 0.4 0.25 0.3 0.1 0.05
S11 3.6 0.7 0.2 0.6 1.2 0.05 0.4 0.26 0.2 0.4 0.1
S12 2.2 0.6 0.3 0.5 1.3 0.05 0.4 0.26 0.3 0.5 0.3
S13 2.2 0.6 0.3 0.4 1.3 0.04 0.4 0.20 0.2 0.3 0.1
S14 1.5 0.4 0.3 0.3 1.2 0.04 0.5 0.20 0.3 0.3 0.3
S15 1.9 0.5 0.3 0.4 1.0 0.06 0.4 0.23 0.3 0.3 0.3
S16 2.1 0.5 0.2 0.4 1.0 0.05 0.4 0.21 0.5 0.5 0.2
S17 2.2 0.6 0.3 0.5 1.0 0.05 0.4 0.23 0.4 0.1 0.2
S18 2.3 0.6 0.2 0.5 1.2 0.05 0.5 0.17 0.2 0.9 0.2
S19 1.3 0.7 0.5 0.4 1.0 0.04 0.4 0.24 0.3 0.9 0.4
S20 1.4 0.6 0.5 0.4 1.0 0.05 0.4 0.24 0.5 0.8 0.4
S21 1.7 0.7 0.4 0.5 1.0 0.04 0.4 0.25 0.6 0.7 0.3
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
117
4.4.5. Ecotoxicological risk characterisation
Two approaches were used to characterise the ecotoxicological risks posed by the pollutant
levels in the harbour sediments, viz. the ones based on numerical sediment quality guidelines
(SQGs) and the total toxicity equivalence (TEQ). In the former, the effect range low (ERL)
and effect range median (ERM) were employed to characterise the potential ecotoxicological
risk posed by individual pollutants in the sediments (Burton, 2002; Long et al., 2006). Both
ERL and ERM have an appreciable level of predictability of sediment toxicity (Long et al.,
1998), viz. low risk for pollutant concentrations at or below ERL, moderate risk for
concentrations above ERL but below ERM, and high risk for concentrations above ERM
(Birch Hutson, 2009). At all the monitoring stations, the γ-HCH concentrations exceeded
the ERM by over an order of magnitude (see Table 4.2), indicating that γ-HCH can potentially
pose a high ecotoxicological risk and should, therefore, be of primary concern. Compared to
this, levels of p,p'-DDE were below the ERL value (low ecotoxicological risk), while the
levels of p,p'-DDT and p,p'-DDD were between their respective ERL and ERM values
(moderate risks) (Table 4.2). The levels of naphthalene, acetylnaphthylene, acenaphthene,
fluorene and phenanthrene were between their ERL and ERM values (Table 4.3) (moderate
risks), whereas the levels of the remaining PAH16 congeners were below their ERL values
(low risks). Since there are no ERLs and ERMs for α-HCH, β-HCH, δ-HCH,
benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[g,h,i]perylene and indeno[1,2,3-
cd]pyrene, the potential ecotoxicological risk posed by these pollutants cannot be
characterised using this approach.
Considering that different pollutants in sediments may potentially act in concert to cause
toxicity different from that of the individual pollutants (Burton, 2002; Long et al., 2006), the
mean ERM quotient (mERMQ) approach (Long et al., 2006; Birch & Hutson, 2009) was
further adopted to characterise the integrated ecotoxicological risks due to the combined effect
of PAHs, DDTs and γ-HCH mixtures in the Tema Harbour sediments investigated. The
mERMQs were evaluated for each sediment sample by normalising the levels of ΣPAHs,
ΣDDTs and γ-HCH to their respective ERM values, then summing the quotients and dividing
by 3 (Long et al., 2006; Birch and Hutson, 2009). The assumptions here are that (1) PAHs,
DDTs and γ-HCH contribute additively to the overall toxicity, rather than antagonistically or
synergistically, and (2) samples with the same mERMQ pose similar ecotoxicological risks
(Long et al., 2006; Birch and Hutson, 2009). Further adopting the risk classification by Birch
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
116
and Hutson (2009), i.e. minimal risk if mERMQ < 0.1, low risk if 0.1 ≤ mERMQ < 0.5,
moderate risk if 0.5 ≤ mERMQ < 1.5, and high risk if mERMQ ≥ 1.5. The results showed that
the Tema Harbour sediments can potentially pose moderate to high ecotoxicological risks as
sediments from 52% of the monitoring stations had mERMQ values exceeding 1.5, while
those from the remaining stations had mERMQ values in the 0.5-1.5 range (Table 4.5). The
spatial pattern of mERMQ (Fig. 4.1d) shows that large areas of the Fishing Harbour and the
Main Harbour are relatively higher risk areas which deserve further management attention.
To provide an integral characterisation for PAH contamination of the harbour sediments, the
total toxicity equivalence (TEQ) approach was used. TEQs at the different stations were
calculated according to Eq. 1 (Nisbet and LaGoy, 1992):
TEQ (mg.kg-1) = Σ(Cn x TEFn) (1)
where Cn and TEFn are, respectively, the concentration (mg.kg-1
) and toxic equivalency factor
(TEF) of an individual PAH congener in the sediment sample. TEFs of the PAH congeners
express their toxicity relative to that of benzo(a)pyrene (Nisbet and LaGoy, 1992) and are
presented in Table 4.3. Sediments can then be classified as uncontaminated for TEQ < 0.1
mg.kg-1
, slightly contaminated for 0.1 < TEQ < 1 mg.kg-1
, and significantly contaminated for
TEQ ≥ 1.0 mg.kg-1
(Yang et al., 2014). Table 4.5 shows that the TEQs associated with Tema
Harbour sediments ranged from 0.2-0.4 mg.kg-1
(mean value 0.3 mg.kg-1
). All TEQ values
were within the 0.1-1.0 mg.kg-1
range, indicating that the harbour sediments are moderately
contaminated by the PAH mixtures (Yang et al., 2014).
The TEQ approach by the USA Environmental Protection Agency (USEPA) for the
assessment of soil contamination by PAH mixtures under Method B of Model Toxics Control
Act (MTCA) Cleanup Regulation (https://fortress.wa.gov/ecy/clarc/FocusSheets/tef.pdf) was
further adopted. This approach is similar to the one by Nisbet and LaGoy (1992), see Eq. 1,
except that a TEF value of 1.0, instead of 5.0, is assigned to dibenz[a,h]anthracene (Table
4.3). Following the USEPA approach, sediments with TEQ values ≥ 0.137 mg.kg-1
are
considered potentially toxic and harmful to environmental health, and therefore require clean-
up. The results show that the TEQ values for all the harbour sediments exceeded 0.137 mg.kg-
1, ranging from 0.164-0.255 mg.kg
-1 (Table 4.5). This indicates that PAH contamination in the
harbour sediments can potentially pose unacceptable risks to ecosystem health. Sediments in
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
117
Table 4.5 Calculated total toxicity equivalence (TEQ) and mean ERM quotient
(mERMQ) values for Tema Harbour sediments
Monitoring
station
aTEQ
(mg.kg-1
)
bTEQ
(mg.kg-1
) mERMQ
S1 0.3 0.164 0.6
S2 0.2 0.172 0.5
S3 0.3 0.176 1.1
S4 0.4 0.195 1.9
S5 0.3 0.199 1.2
S6 0.4 0.203 0.6
S7 0.3 0.205 1.5
S8 0.3 0.206 1.1
S9 0.3 0.210 1.6
S10 0.4 0.217 1.3
S11 0.3 0.219 0.7
S12 0.3 0.221 0.8
S13 0.3 0.222 1.5
S14 0.4 0.224 1.9
S15 0.4 0.225 1.8
S16 0.4 0.228 1.2
S17 0.3 0.231 1.4
S18 0.4 0.238 2.0
S19 0.3 0.248 1.8
S20 0.4 0.255 1.5
S21 0.3 0.255 1.6
Mean 0.3 0.215 1.3
Threshold 0.1 0.137 0.1
aNisbet and LaGoy (1992) method
bUSEPA method (https://fortress.wa.gov/ecy/clarc/FocusSheets/tef.pdf)
a c
d
a
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
118
the Main Harbour may be associated with relatively lower risks compared to the other parts of
the Tema Harbour (Fig. 4.1e).
It should be noted that the ecotoxicological risk assessment was at a screening-level and only
established the likelihood of DDTs, HCHs and PAH16 contamination in the harbour sediments
to cause undesirable biological effects. Information on the hazard associated with harbour
sediments from e.g. whole sediment bioassays, which integrate the effects of other pollutants
such as heavy metals, are required to inform decisions about the handling of the harbour
sediments. This baseline study nevertheless clearly shows there is a need to step up pollution
control, prevention and management efforts by the Tema Harbour and responsible
government authorities.
4.5. Conclusion
In conclusion, DDTs (p,p'-DDT, p,p'-DDE and p,p'-DDD), HCHs (-HCH, -HCH, -HCH
and -HCH) and the USEPA 16 priority PAHs (PAH16) are ubiquitous in the Tema Harbour
sediments. The harbour sediments were predominantly sandy, with no significant correlations
between the silt-clay/TOC contents and the concentrations of most of the pollutants
investigated, probably due to the temporal and spatial variable contaminant loadings as well
as redistribution by water currents. DDT in the Tema Harbour sediments has undergone
considerable weathering to p,p'-DDD and thus, DDT contamination in sediments is
attributable to the impact of past use of DDT. The concentrations of -HCH in Tema Harbour
sediments were higher than those of -HCH, -HCH and -HCH, suggesting that HCH
contamination relates to past use of lindane. The PAH16 concentrations in the sediments may
pose appreciable ecotoxicological risks. γ-HCH was identified as a contaminant of potential
concern. This baseline study has shown that there is a need to regulate discharges of PAHs
into the harbour, considering their high potential toxicity.
References
Ahrens, M.J. & Depree, C.V., 2004. Inhomogeneous distribution of polycyclic aromatic
hydrocarbons in different size and density fractions of contaminated sediment from
Auckland Harbour, New Zealand: an opportunity for mitigation. Mar. Pollut. Bull.
48(3), 341-350.
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
119
Botwe, B. O., Nyarko, E., & Ntow, W. J. (2012). Pesticide Contamination in Groundwater
and Streams Draining Vegetable Plantations in the Ofinso District, Ghana. In:
Hernandez-Soriano, M.C. (Ed.), Soil Health and Land Use Management, InTech, pp.
51-66. Rijeka, Croatia.
Birch, G.F. & Hutson, P., 2009. Use of sediment risk and ecological/conservation value for
strategic management of estuarine environments: Sydney estuary, Australia. Environ.
Manage. 44(4), 836-850.
Burdige, D.J., 2007. Preservation of organic matter in marine sediments: controls,
mechanisms, and an imbalance in sediment organic carbon budgets? Chem. Rev.
107(2), 467-485.
Burton, G.A. Jr., 2002. Sediment quality criteria in use around the world. Limnology, 3(2), 65-
76.
Caille, N., Tiffreau, C., Leyval, C. & Morel, J.L., 2003. Solubility of metals in an anoxic
sediment during prolonged aeration. Sci. Total Environ. 301(1), 239-250.
De Luca, G., Furesi, A., Leardi, R., Micera, G., Panzanelli, A., Piu, P.C. & Sanna, G., 2004.
Polycyclic aromatic hydrocarbons assessment in the sediments of the Porto Torres
Harbour (Northern Sardinia, Italy). Mar. Chem. 86(1), 15-32.
Fung, C., Zheng, G., Connell, D., Zhang, X., Wong, H., Giesy, J.P., Fang, Z. & Lam, P.K.S.,
2005. Risks posed by trace organic contaminants in coastal sediments in the Pearl
River Delta, China. Mar. Pollut. Bull. 50(10), 1036-1049.
Gorleku, M.A., Carboo, D., Palm, L.M.N., Quasie, W.J. & Armah, A.K., 2014. Polycyclic
aromatic hydrocarbons (PAHs) pollution in marine waters and sediments at the Tema
Harbour, Ghana. Acad. J. Environ. Sci. 2(7), 108-115.
Hong, H., Xu, L.-J., Zhang, L., Chen, J., Wong, Y. & Wan, T., 1995. Special guest paper:
environmental fate and chemistry of organic pollutants in the sediment of Xiamen and
Victoria Harbours. Mar. Pollut. Bull. 31(4), 229-236.
Hu, W., Wang, T., Khim, J. S., Luo, W., Jiao, W., Lu, Y., Naile, J.E., Chen, C., Zhang, X. &
Giesy, J.P., 2010. HCH and DDT in sediments from marine and adjacent riverine areas
of North Bohai Sea, China. Arch. Environ. Contam. Toxicol. 59(1), 71-79.
Islam, M.S. & Tanaka, M., 2004. Impacts of pollution on coastal and marine ecosystems
including coastal and marine fisheries and approach for management: a review and
synthesis. Mar. Pollut. Bull. 48(7-8), 624-649.
Kelderman, P., 2012. Sediment pollution, transport, and abatement measures in the city canals
of Delft, The Netherlands. Water Air Soil Pollut. 223(7), 4627-4645.
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
120
King, A., Readman, J. & Zhou, J., 2004. Dynamic behaviour of polycyclic aromatic
hydrocarbons in Brighton marina, UK. Mar. Pollut. Bull. 48(3), 229-239.
Li, P., Wang, Y., Huang, W., Yao, H., Xue, B. & Xu, Y., 2014. Sixty-year sedimentary record
of DDTs, HCHs, CHLs and endosulfan from emerging development gulfs: a case
study in the Beibu Gulf, South China Sea. Bull. Environ. Contam. Toxicol. 92(1), 23-
29.
Lin, T., Hu, Z., Zhang, G., Li, X., Xu, W., Tang, J. & Li, J., 2009. Levels and mass burden of
DDTs in sediments from fishing harbours: the importance of DDT-containing
antifouling paint to the coastal environment of China. Environ. Sci. Technol. 43(21),
8033-8038.
Long, E.R., Field, L.J. & MacDonald, D.D., 1998. Predicting toxicity in marine sediments
with numerical sediment quality guidelines. Environ Toxicol and Chem. 17(4), 714-
727.
Long, E.R., Ingersoll, C.G. & MacDonald, D.D., 2006. Calculation and uses of mean
sediment quality guideline quotients: a critical review. Environ. Sci. Technol. 40(6),
1726-1736.
Maruya, K.A., Risebrough, R.W. & Horne, A.J., 1996. Partitioning of polynuclear aromatic
hydrocarbons between sediments from San Francisco Bay and their porewaters.
Environ. Sci. Technol. 30(10), 2942-2947.
Mestres, M., Sierra, J., Mösso, C. & Sánchez-Arcilla, A., 2010. Sources of contamination and
modelled pollutant trajectories in a Mediterranean harbour (Tarragona, Spain). Mar.
Pollut. Bull. 60(6), 898-907.
Neff, J.M., Stout, S.A. & Gunster, D.G., 2005. Ecological risk assessment of polycyclic
aromatic hydrocarbons in sediments: identifying sources and ecological hazard. Integr.
Environ. Assess. Manage. 1(1), 22-33.
Nisbet, I.C. & LaGoy, P.K., 1992. Toxic equivalency factors (TEFs) for polycyclic aromatic
hydrocarbons (PAHs). Regul. Toxicol. Pharm. 16(3), 290-300.
Ntow, W.J & Botwe, B.O., 2011. Contamination status of organochlorine pesticides in Ghana.
In: Loganathan, B.G. & Lam, P.K.S. (Eds), Global Contamination Trends of Persistent
Organic Chemicals. pp. 393-411. CRC Press, USA.
Nyarko, E., Botwe, B.O. & Klubi, E., 2011. Polycyclic aromatic hydrocarbons (PAHs) levels
in two commercially important fish species from the coastal waters of Ghana and their
carcinogenic health risks. West Afr. J. Appl. Ecol. 19(1), 53-66.
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
121
Phillips, C.R., 2007. Sediment contaminant patterns within coastal areas of the Southern
California Bight: multivariate analyses of Bight'98 Regional Monitoring Data. Bull. S.
California Acad. Sci. 106(3), 163-178.
Sáez-Plaza, P., Michałowski, T., Navas, M.J., Asuero, A.G. Wybraniec, S., 2013. An
overview of the Kjeldahl method of nitrogen determination. Part I. Early history,
chemistry of the procedure, and titrimetric finish. Crit. Rev. Anal. Chem. 43(4), 178-
223.
Schumacher, B.A., 2002. Methods for the determination of total organic carbon (TOC) in
soils and sediments. USEPA Environmental Sciences Division National Exposure
Research Laboratory, Ecological Risk Assessment Support Centre, Office of Research
and Development. pp. 1-23. Las Vegas, USA
Simpson, C.D., Mosi, A.A., Cullen, W.R. & Reimer, K.J., 1996. Composition and distribution
of polycyclic aromatic hydrocarbon contamination in surficial marine sediments from
Kitimat Harbour, Canada. Sci. Total Environ. 181(3), 265-278.
Singh, A., & Lal, R. (2009). Sphingobium ummariense sp. nov., a hexachlorocyclohexane
(HCH)-degrading bacterium, isolated from HCH-contaminated soil. Int. J. Syst. Evol.
Microbiol. 59(1), 162-166.
Smith, J., Lee, K., Gobeil, C. & Macdonald, R., 2009. Natural rates of sediment containment
of PAH, PCB and metal inventories in Sydney Harbour, Nova Scotia. Sci. Total
Environ. 407(17), 4858-4869.
Tesi, T., Miserocchi, S., Goňi, M.A., Langone, L., Boldrin, A. Turchetto, M., 2007.
Organic matter origin and distribution in suspended particulate materials and surficial
sediments from the western Adriatic Sea (Italy). Estuar. Coast. Shelf Sci. 73(3), 431-
446.
Walker, K., Vallero, D.A. & Lewis, R.G., 1999. Factors influencing the distribution of lindane
and other hexachlorocyclohexanes in the environment. Environ. Sci. Technol. 33(24),
4373-4378.
Wang, X.-C., Sun, S., Ma, H.-Q. & Liu, Y., 2006. Sources and distribution of aliphatic and
polyaromatic hydrocarbons in sediments of Jiaozhou Bay, Qingdao, China. Mar.
Pollut. Bull. 52(2), 129-138.
Wang, X.-C., Zhang, Y.-X. & Chen, R.F., 2001. Distribution and partitioning of polycyclic
aromatic hydrocarbons (PAHs) in different size fractions in sediments from Boston
Harbour, United States. Mar. Pollut. Bull. 42(11), 1139-1149.
Assessment of DDT, HCH and PAH Contamination and Associated Ecotoxicological Risks in Surface Sediments of Coastal Tema Harbour (Ghana)
122
WHO (World Health Organisation), 1989. DDT and its derivatives: Environmental aspects.
Environmental Health Criteria 83. Geneva.
Willett, K.L., Ulrich, E.M. & Hites, R.A., 1998. Differential toxicity and environmental fates
of hexachlorocyclohexane isomers. Environ. Sci. Technol. 32(15), 2197-2207.
Yang, R.-q., Jiang, G.-b., Zhou, Q.-f., Yuan, C.-g. & Shi, J.-b., 2005. Occurrence and
distribution of organochlorine pesticides (HCH and DDT) in sediments collected from
East China Sea. Environ. Int. 31(6), 799-804.
Yang, Y., Woodward, L.A., Li, Q. X. & Wang, J., 2014. Concentrations, Source and Risk
Assessment of Polycyclic Aromatic Hydrocarbons in Soils from Midway Atoll, North
Pacific Ocean. PLoS One, 9(1): 1-7.
Ye, S., Laws, E.A. & Gambrell, R., 2013. Trace element remobilisation following the
resuspension of sediments under controlled redox conditions: City Park Lake, Baton
Rouge, LA. Appl. Geochem. 28, 91-99.
Yu, H.-Y., Shen, R.-L., Liang, Y., Cheng, H. & Zeng, E.Y., 2011. Inputs of antifouling paint-
derived dichlorodiphenyltrichloroethanes (DDTs) to a typical mariculture zone (South
China): potential impact on aquafarming environment. Environ. Pollut. 159(12), 3700-
3705.
Yunker, M.B., Macdonald, R.W., Brewer, R., Sylvestre, S., Tuominen, T., Sekela, M.,
Mitchell, R.H., Paton, D.W., Fowler, B.R., Gray, C., Goyette, D. & Sullivan, D., 2000.
Assessment of natural and anthropogenic hydrocarbon inputs using PAHs as tracers.
The Fraser River basin and Strait of Georgia, 1987-1997. Burrard Inlet Environmental
Action Programme, Canada.
Yunker, M.B., Macdonald, R.W., Vingarzan, R., Mitchell, R.H., Goyette, D. & Sylvestre, S.,
2002. PAHs in the Fraser River basin: a critical appraisal of PAH ratios as indicators
of PAH source and composition. Org. Geochem. 33(4), 489-515.
Chapter 5
Metal Distribution and
Fractionation in Surface
Sediments of Coastal Tema
Harbour (Ghana) and its
Ecological Implications
A modified version of this chapter was published as: Botwe, B.O., Alfonso, L., Nyarko, E., &
Lens, P.N.L. (2017). Metal Distribution and Fractionation in Surface Sediments of Coastal
Tema Harbour (Ghana) and its Ecological Implications. Environmental Earth Sciences, 76,
514-530.
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
124
Abstract
This study investigated the distribution and fractionation of metals (Mn, Ni, Pb, Cr, Cu, Zn,
As, Cd, Hg and Sn) in surface sediments of Tema Harbour (Greater Accra, Ghana) as well as
its ecological implications. Significant differences in sediment concentrations of Mn, Ni, Cr,
Cu, Zn, As and Sn were observed across the Tema Harbour. Geochemical indices indicate that
Cd, Hg, Pb, Cu, Zn, As and Sn in the Tema Harbour sediments derived mainly from
anthropogenic sources, while Mn, Ni and Cr were mainly of lithogenic origin. Metal
fractionation revealed a predominance of Al, Mn, Ni, Pb, Cr, Cu, As and Sn in the residual
phase. In contrast, Cd and Hg were mainly present in the exchangeable phase, while Zn was
mainly associated with the reducible phase. Based on the metal fractionation in the Tema
Harbour sediments, the potential risks of metal bioavailability were high for Cd and Hg, low-
medium for Mn, Ni, Zn, As and Sn, and low for Pb, Cr, and Cu. A screening-level
ecotoxicological assessment revealed high potential toxicity of Hg and moderate potential
toxicities of Pb, Cu, Zn, As and Cd in the Tema Harbour sediments. The potential influence of
the buffer intensity, silt-clay, total organic carbon and carbonate content on the metal
distribution in the Tema Harbour sediments were also inferred from their correlations.
Comparison with previous studies did not reveal a progressive increase in metal
contamination at the Tema Harbour since the year 2000.
5.1. Introduction
Harbour sediments are often contaminated with a wide range of pollutants including metals
(Casado-Martinez et al. 2006; Palma and Mecozzi 2007), which derive from anthropogenic
activities associated with harbours such as shipping, fishing as well as industrial and urban
wastewater discharges (Lepland et al. 2010; Schipper et al. 2010; Nyarko et al. 2014; Botwe
et al. 2017a). Polluted sediments are potential secondary sources of chemical pollutants to
benthic organisms living in contact with sediments and ultimately to other organisms within
the food chain (Burton 2002; Kelderman and Osman 2007; Nyarko et al. 2011; Botwe et al.
2017a). Metals such as Ni, Pb, Cr, Cu, Zn, As, Cd and Hg are hazardous to marine organisms
(Casado-Martinez et al. 2006; Schipper et al. 2010) and their contamination in the
environment has adverse human health, socioeconomic and food security implications (Birch
and Hutson 2009; Lepland et al. 2010; Botwe et al. 2017a). Contaminated harbour sediments
may adversely impact other coastal marine and terrestrial ecosystems via the disposal of
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
125
dredged materials (Caille et al. 2003; Schipper et al. 2010; Ho et al. 2012a; Botwe et al.
2017a).
Considering the threat contaminated sediments may pose to aquatic and terrestrial ecosystems,
remediation of contaminated sediments is a priority for environmental management in
harbours (Pozza et al. 2004). Remediation of harbour sediments requires a prior screening of
the sediments for their potential ecotoxicity and environmental risks in order to obtain
information on (1) pollutants of prime concern, (2) the potential to cause adverse biological
effects in benthic organisms and (3) identify the most impacted areas that deserve priority
attention (Burton 2002; Long et al. 2006; Birch and Hutson 2009; Botwe et al. 2017a). A
screening-level ecotoxicological assessment of sediments involves comparisons of measured
pollutant concentrations in the sediment with established biological effect-based sediment
quality guidelines (SQGs) (Long et al. 1995; Burton 2002; Botwe et al. 2017a). Two SQGs
which have been widely used around the world for ecotoxicological screening of sediments
are the effects-range low (ERL) and effects-range median (ERM) SQGs (Long et al. 1995;
Burton 2002; Botwe et al. 2017a).
Sediment-bound metals may associate with different geochemical phases present in
sediments, e.g. carbonate, Fe-Mn oxides and hydroxides, organic matter and sulphides. The
phase association (fractionation) of metals in sediments determines their binding strength and
consequently, their potential mobility and bioavailability (Calmano et al. 1993; Pueyo et al.
2001; Kelderman and Osman 2007; Ho et al. 2012b; Hamzeh et al. 2014). Investigation of the
metal distribution over different geochemical phases (metal fractionation) in sediments is,
therefore, relevant when screening the sediments for their potential environmental risks. A
standardised procedure widely used for metal fractionation in sediments is the Community
Bureau of Reference (BCR) three-step sequential extraction technique, which yields four
metal fractions, namely the acid-soluble (exchangeable and bound to carbonate), reducible
(bound to Fe-Mn oxides and hydroxides), oxidisable (bound to organic matter and sulphides)
and residual (bound within the crystal lattice of minerals) fractions (Quevauviller et al. 1997;
Pueyo et al. 2001; Ho et al. 2012a). Since metal fractionation and potential mobility in
sediments are influenced by environmental factors such as pH, buffer intensity and redox
potential (Calmano et al. 1993; Kelderman and Osman 2007; Palma and Mecozzi 2007; Ho et
al. 2012a; Hamzeh et al. 2014), these factors should be considered in characterising the
potential environmental risk of metal-contaminated sediments.
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
126
The coastal marine Tema Harbour in Greater Accra (Ghana) was constructed in 1960 and
commissioned in 1962 to facilitate international trade and boost industrial development in
Ghana. Thus, the Tema Harbour was sited at the seacoast of the industrial city of Tema,
Greater Accra in Ghana and its commissioning marked the beginning of Ghana's industrial
era. With over 180 industries in Tema, as well as shipping and fishing activities at the Tema
Harbour, the Tema Harbour is susceptible to metal pollution (Lepland et al. 2010; Schipper et
al. 2010; Nyarko et al. 2014). Previous studies in 2000
(http://open_jicareport.jica.go.jp/pdf/11681632_03.pdf) and 2011 (Nyarko et al. 2014)
characterised metal contamination levels in the Tema Harbour. However, the above studies
focused on total metal concentrations without examining metal fractionation in the Tema
Harbour sediments. Moreover, the Tema Harbour sediments have not been characterised for
their buffer intensity against acidification, which determines metal leachability and associated
environmental risk (Calmano et al. 1993; Jain 2004; Iqbal et al. 2013; Ho et al. 2012a). The
objective of this study was, therefore, to investigate the distribution and fractionation of
metals (Mn, Ni, Pb, Cr, Cu, Zn, As, Cd, Hg and Sn) in surface sediments from the Tema
Harbour as well as its ecological implications.
5.2. Materials and methods
5.2.1. Sediment sampling and sample analyses
Surface sediment samples were collected in November 2014 with a stainless steel Ekman grab
(3.5 L) from 21 stations across the different compartments of the Tema Harbour, which were
previously monitored for organic (Botwe et al. 2017a) and radioactivity (Botwe et al. 2017b)
contamination. Thus, sediment samples were collected from fourteen stations in the Main
Harbour, two stations each in the Inner Fishing Harbour and the Outer Fishing Harbour, and
three stations in the Canoe Basin (see Fig. 3.1). The Main Harbour is where ships call at the
Tema Harbour, and has a total of 14 berths. The Inner Fishing Harbour and the Outer Fishing
Harbour provide handling facilities for semi-industrial and industrial fishing vessels, while the
Canoe Basin serves as an artisanal canoe fishing landing site. Adopting the sampling strategy
by Botwe et al. (2017a), three grab samples were collected at each station. Only grabs that
arrived on the deck firmly closed without water leakage and were not filled with sediment to
the lid were sampled to ensure that the fine particles were not lost and the surface layer was
intact (Aloupi and Angelidis 2001; Botwe et al. 2017b).
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
127
From each grab, two sub-samples each of about 200 g wet weight were taken with acid-
washed plastic spoons from the upper 0-2 cm layer, which is representative of recently
deposited sediments (Phillips 2007; Botwe et al. 2017a), into acid-washed FoodSaver® zipper
bags. One subsample was for the analyses of metals, total organic carbon (TOC), carbonate,
pH (and subsequently buffer intensity) and the other for grain size analysis. Samples for metal
analysis were vacuum-sealed to minimise oxidation. To avoid contamination, sediments in
direct contact with the grab were not sampled (Botwe et al. 2017b). Redox potential was
measured in situ near the sediment-water interface using a Hanna multiparameter probe (HI
9829) following Botwe et al. (2017b). All sediment samples were kept on ice and transported
to the University of Ghana laboratory for further analysis.
In the laboratory, the silt-clay (<63 µm) and sand (63-2000 µm) fractions in the sediment
samples were determined on wet samples by the wet sieving method following the method by
Wang et al. (2001). Sediment samples for metal, total organic carbon (TOC), carbonate and
pH analyses were freeze-dried and then homogenised using a Fritsch Pulveriser. Total metal
concentrations and metal fractionation were determined on about 0.2 g portions of freeze-
dried homogenised sediment samples by adopting the harmonised Community Bureau of
Reference (BCR) 3-step sequential extraction and aqua regia extraction techniques,
respectively, following Pueyo et al. (2001). Metal concentrations were assayed using an
Atomic Absorption Spectrometer (Varian AA 240FS). The detection limits for the measured
metals were: 0.10 for Al, Hg and As; 0.20 for Cd; 0.50 for Mn, Ni, Pb, Cr, Zn, Cd, and Sn;
and 1.0 for Cu. The TOC content was determined on 1 g of dry homogenised sediment sample
using the Walkley-Black wet oxidation method after decarbonisation of the sediment with
excess HCl (Schumacher 2002; Botwe et al. 2017a). The carbonate content was analysed by
treating sediment samples with excess HCl (1 M), followed by titration with 0.5 M NaOH
(Kelderman and Osman 2007). The sediment pH was determined on 10 g portions of
homogenised sediment samples after the addition of 25 mL deionised water following Palma
and Mecozzi (2007).
To characterise stability of the Tema Harbour sediment against small changes in pH, the
buffer intensities of the sediments were evaluated following the procedure described by
Calmano (1988). Briefly, 5 g portions of sediment were suspended in 50 mL deionised water
(10% sediment suspensions) in acid-washed 50 mL polypropylene tubes and shaken on an
end-to-end shaker for 1 h, after which the pH of the supernatant solutions (pHo) were
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
128
measured. This procedure was repeated using 50 mL of 0.1 M HCl and the corresponding pH
(pHx) measured. The buffer intensity (δpH) was determined using Eq. (1) (Calmano 1988):
δpH = pHo - pHx (1)
The buffer intensities of the sediments were characterised as follows: δpH < 2 (strongly
buffered), δpH = 2-4 (intermediate), and δpH > 4 (poorly buffered) (Calmano 1988).
For quality assurance and control, chemicals, solvents and reagents used in the extraction
were of trace metal analysis grade. All containers used were either new or thoroughly cleaned
by washing with detergent, soaking in 10% HNO3 solution overnight and rinsing with
deionised water. A sediment certified reference material (BCR-701) and blanks were analysed
with the sediment samples. Sediment samples were analysed in triplicates. Metal recoveries
ranged from 69.2-109% for the investigated metals, with relative standard deviations (RSD) in
the range of 2.2-12.5 %. The reported metal concentrations were corrected for recoveries,
using their respective mean recoveries from the certified reference materials.
5.2.2. Metal enrichment and contamination level
Metal enrichment factors (EFs) were derived for the measured metals to characterise their
enrichment in the Tema Harbour sediments based on Eq. (2) (Dung et al. 2013; Mahu et al.
2015):
EF = [M/Al]Sample/[M/Al]Crust (2)
where (M/Al)Sample is the metal-aluminium ratio for the Tema Harbour sediment sample and
(M/Al)Crust is the metal-aluminium ratio for the continental crust. EF ≤ 1 indicates no
enrichment, 1 < EF ≤ 3: minor enrichment, 3 < EF ≤ 5: moderate enrichment, 5 < EF ≤ 10:
moderately severe enrichment, 10 < EF ≤ 25: severe enrichment, 25 < EF ≤ 50: very severe
enrichment, and EF > 50: extremely severe enrichment (Dung et al. 2013).
Geo-accumulation indices (Igeo) were evaluated to assess the extent of metal contamination in
the Tema Harbour sediments using Eq. (3) (Dung et al. 2013; Mahu et al. 2015):
Igeo = Log2 (Ms/1.5Mb) (3)
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
129
where Ms is the metal concentration in the Tema Harbour sediment, Mb is its average crustal
concentration and 1.5 is introduced as a background matrix correction due to lithogenic
effects (Addo et al. 2011; Iqbal et al. 2013; Mahu et al. 2015). Igeo < 0: unpolluted; 0 ≤ Igeo <
1: unpolluted to moderately polluted; 1 ≤ Igeo < 2: moderately polluted; 2 ≤ Igeo 3: moderately
to highly polluted; 3 ≤ Igeo < 4: heavily polluted; 4 ≤ Igeo < 5: highly to very highly polluted;
Igeo ≥ 5: very heavily polluted (Dung et al. 2013).
In the evaluation of the EFs and Igeo, the average crustal concentrations of the metals (Taylor
1964) were used as proxies for the background concentration (Table 5.1), since pre-impacted
or deep-core metal concentration data are not available for the Tema Harbour.
5.2.3. Data treatment
Pearson's product-moment correlations were performed to determine linear relationships
between the measured sediment parameters using the Statistical Package for Social Sciences
(SPSS 16.0) software. Descriptive statistics (means, standard deviations and coefficients of
variation) were performed in Microsoft Excel 2007 for Windows at the 95% confidence
interval. The spatial distribution patterns of metal concentrations in the Tema Harbour
sediments were mapped in ArcGIS 10.2.2. One-way analysis of variance (ANOVA) with
multiple comparison (Holm-Sidak and Kruskal-Wallis) tests was performed in SigmaPlot 11.0
to determine spatial differences in sediment metal concentrations in the Tema Harbour.
5.3. Results
5.3.1. Physicochemical characteristics of the Tema Harbour sediments
The sediment physicochemical parameters and in situ redox potential (Eh) at the sediment-
water interface in the Tema Harbour are shown in Table 5.1. The Tema Harbour sediments
were composed mainly of the silt-clay (<63 µm) fraction with a mean composition of 70 (±
4)%. The sediment TOC and carbonate contents were in the ranges of 1.1-6.0% and 8.8-
10.6%, respectively. The Tema Harbour sediments were slightly alkaline (pH range of 7.3-
8.3) with buffer intensities in the range of 1.0-2.7, while the bottom water was anoxic with Eh
values ranging from -70 to -350 mV. Sediments from the Canoe Basin were mostly anoxic.
The silt-clay content, Eh and buffer intensity varied significantly across the Tema Harbour
compartments. On the contrary, the pH, TOC and carbonate contents did not vary
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
130
significantly across the Tema Harbour compartments. Table 5.2 shows that the silt-clay
content correlated significantly with the Mn (r = 0.52, p < 0.05), Ni (r = 0.52, p < 0.05), Cr (r
= 0.58, p < 0.01), Cu (r = 0.60, p < 0.01), Zn (r = 0.75, p < 0.01), As (r = 0.64, p < 0.01) and
Sn (r = 0.50, p < 0.05) concentrations in the Tema Harbour sediments. The TOC content
correlated with the Mn (r = 0.48, p < 0.05), Ni (r = 0.46, p < 0.05) and Cu (r = 0.49, p < 0.05)
concentrations. The carbonate content correlated with the Hg concentration (r = 0.47, p <
0.05). The buffer intensity correlated with the Cr (r = 0.85, p < 0.01), Zn (r = 0.71, p < 0.01),
As (r = 0.83, p < 0.01) and Sn (r = 0.65, p < 0.01) concentrations as well as with the silt-clay
content (r = 0.55, p < 0.01). Sediment pH did not correlate significantly with the metal
concentrations in the Tema Harbour sediments.
5.3.2. Metal concentrations and distribution patterns in sediments of Tema Harbour
The total metal concentrations in the Tema Harbour sediments are presented in Table 5.1.
Overall, the mean sediment metal concentrations were: Al (17930 ± 780 mg.kg-1
dw), Mn
(210 ± 7 mg.kg-1
dw), Ni (23 ± 1 mg.kg-1
dw), Cr (72 ± 3 mg.kg-1
dw), Pb (88 ± 13 mg.kg-1
dw), Cu (102 ± 16 mg.kg-1
dw), Zn (260 ± 40 mg.kg-1
dw), As (14.2 ± 0.6 mg.kg-1
dw), Cd
(8.1 ± 0.6 mg.kg-1
dw), Hg (1.5 ± 0.3 mg.kg-1
dw) and Sn (8.2 ± 1.7 mg.kg-1
dw). Significant
positive correlations were observed among most of the sediment metal concentrations (Table
5.2). The Mn and Ni concentrations showed a perfect correlation (r = 1.00, p < 0.01) and both
correlated significantly with all the other metals, except Pb, Hg and Sn. Cd exhibited
significant correlations with all the metals except Cr. Pb exhibited a significant correlation
with only Al (r = 0.60, p < 0.01), whereas Hg did not exhibit any significant correlation with
all the other metals investigated.
The spatial distribution patterns of the metals are shown in Fig. 5.1. Sediment Al
concentrations were relatively higher in the Inner Fishing Harbour and the Main Harbour
entrance stations. Mn concentrations were relatively higher in the Fishing Harbour, Canoe
Basin, and the entrance and mid-section of the Main Harbour. Relatively higher Ni
concentrations occurred in the north-eastern corner of the Main Harbour. Sediments from the
Fishing Harbour and the Canoe Basin contained relatively higher Cr concentrations. Sediment
concentrations of As were relatively higher in the Inner Fishing Harbour and the Canoe Basin.
Relatively higher sediment Cd concentrations occurred in the Inner Fishing Harbour.
Sediments from the Canoe Basin and the Fishing Harbour contained relatively higher concent-
Table 5.1 Sediment metal concentrations and physicochemical parameters measured in the Tema Harbour, Ghana, their average crustal
concentrations and metal concentrations in Tema Harbour sediments from previous studies in 2000 and 2010-2011.
Metal concentration (mg.kg-1
dry weight)
Physicochemical parameters
Harbou
r area
Sampling
station Al Mn Ni Pb Cr Cu Zn As Cd Hg Sn
Silt-clay
(%)
TOC
(%)
CaCO3
(%) pH
Buffer
intensity
Eh
(mV)
MH 1 17980 194 21.0 30.5 69.2 81.1 205 14.9 7.5 2.6 23.9
67 4.5 9.5 8.0 1.9 -110
2 14170 165 21.3 49.3 57.8 77.2 160 10.0 5.1 2.1 28.8
67 5.4 9.4 8.0 1.4 -130
3 14100 160 21.1 45.3 56.6 75.1 155 9.6 7.5 1.4 10.6
67 4.7 9.7 7.7 1.6 -100
4 27500 270 26.2 36.3 73.9 79.4 185 15.0 8.7 1.9 12.7
68 5.8 9.0 7.6 1.0 -90
5 19280 210 22.8 38.1 66.3 43.3 124 14.5 8.1 0.4 0.8
39 6.0 9.0 8.0 1.0 -90
6 17640 195 21.6 40.0 63.0 44.8 128 14.2 17.7 0.4 0.6
70 2.4 10.6 8.0 1.3 -90
7 14170 183 21.4 57.6 58.9 42.5 164 10.0 4.3 0.4 0.7
53 1.1 9.8 7.6 1.3 -80
8 17890 177 24.7 33.1 63.3 34.2 77 14.0 8.0 0.3 0.5
57 2.2 9.7 7.3 1.4 -90
9 19070 187 23.2 56.8 60.9 46.5 110 9.8 9.2 0.6 0.7
84 5.4 9.5 8.0 1.3 -80
10 16730 198 20.0 68.4 58.8 44.5 89 14.9 6.0 0.3 0.7
62 2.2 9.3 8.1 1.3 -70
11 16220 198 21.9 63.3 70.2 30.9 137 14.1 5.4 0.4 0.6
52 4.7 9.5 7.8 1.3 -80
12 18100 187 26.1 57.8 55.8 36.2 123 12.6 7.7 0.8 0.9
71 4.1 9.2 7.6 1.3 -90
13 20260 223 35.9 79.9 77.6 78.7 208 15.6 5.8 0.9 14.7
66 5.8 9.6 7.8 1.4 -90
14 16840 250 27.6 73.5 71.6 66.3 170 15.3 9.4 0.7 11.3
80 4.5 9.2 8.3 1.3 -90
CB 15 15810 240 18.7 230 71.3 196 576 17.0 6.9 0.8 7.8
85 4.7 9.4 8.2 2.7 -350
16 15420 230 20.9 206 77.3 180 561 14.0 8.2 4.3 6.8
80 4.2 8.8 7.6 2.1 -260
17 13870 210 20.1 216 65.6 168 532 15.8 5.9 4.5 9.0
82 4.0 9.4 7.5 2.7 -240
IFH 18 19050 270 22.6 130 110 264 518 21.3 9.2 1.6 12.9
89 5.8 9.0 7.8 1.8 -130
19 26710 260 30.4 122 106 220 500 18.7 12.7 2.2 14.0
87 5.4 9.8 7.6 1.7 -140
OFH 20 18780 250 21.9 107 89.4 170 395 15.1 8.7 2.6 7.9
92 5.3 9.4 7.9 2.3 -150
21 16970 220 19.9 97.6 95.4 163 240 13.7 7.1 2.2 6.4
93 5.5 9.2 7.8 1.7 -160
Mean 17930 210 23 88 72 102 260 14.2 8.1 1.5 8.2
70 4.5 9.4 - 1.6 -
*ACC 82300 950 75 12.5 100 55 70 1.8 0.2 0.08 2
a
Year 2000 - - - 51.5 209 - - 9.2 0.2 4.4 -
b Year
2010-2011 - 41.7 34.2 - nd 25.8 28.5 1.5 13.4 - -
MH = Main Harbour; CB = Canoe Basin; IFH = Inner Fishing Harbour; OFH = Outer Fishing Harbour; *ACC = average crustal concentration (Taylor 1964)
a JICA (http://open_jicareport.jica.go.jp/pdf/11681632_03.pdf);
b Nyarko et al. (2014); nd = not detected; '-' = not applicable or not measured.
Table 5.2 Correlation matrix of measured metals and physicochemical characteristics of surface sediments from Tema Harbour,
Ghana (2-tailed; n = 21)
Al Mn Ni Pb Cr Cu Zn As Cd Hg Sn
Silt-
clay TOC Carbonate pH
Mn 0.61**
Ni 0.61** 1.00**
Pb 0.60** 0.30 0.30
Cr -0.20 0.44* 0.44* -0.22
Cu 0.48* 0.78** 0.78** 0.23 0.36
Zn 0.16 0.67** 0.67** 0.09 0.76** 0.81**
As 0.04 0.61** 0.61** -0.12 0.91** 0.61** 0.92**
Cd 0.44* 079** 0.79** 0.23 0.45* 0.74** 0.69** 0.61**
Hg 0.42 0.27 027 0.15 -0.10 0.26 0.12 0.06 0.28
Sn -0.05 0.27 0.27 -0.19 0.58** 0.32 0.61** 0.67** 0.18 -0.08
Silt-clay 0.12 0.52* 0.52* -0.03 0.58** 0.60** 0.75** 0.64** 0.36 0.27 0.50*
TOC 0.42 0.48* 0.46* 0.29 0.12 0.49* 0.40 0.27 0.27 -0.01 0.27 0.34
Carbonate -0.07 -0.40 -0.40 0.07 -0.29 -0.23 -0.29 -0.27 -0.20 0.47* -0.34 -0.13 -0.48
pH -0.16 0.10 0.10 -0.17 -0.05 -0.08 -0.08 -0.10 -0.04 0.11 -0.31 0.10 0.20 -0.02
BI -0.31 0.25 0.25 -0.37 0.85** 0.29 0.71** 0.83** 0.35 -0.11 0.65** 0.60** 0.07 -0.09 -0.03
*Correlation is significant at the 0.05 level.
** Correlation is significant at the 0.01 level.
BI = Buffer intensity
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
133
rations of Pb, Cu, Zn and Hg, while sediments from the north-eastern corner of the Main
Harbour contained higher concentrations of Sn. Analysis of variance (ANOVA) revealed that
the Mn, Ni, Cr, Cu, Zn, As and Sn concentrations differed significantly (p < 0.05) among the
Main Harbour, the Inner Fishing Harbour, the Outer Fishing Harbour and the Canoe Basin.
5.3.3. Metal fractionation, enrichment and pollution in Tema Harbour sediments
The distribution of metals over the acid-soluble, reducible, oxidisable and residual phases of
sediments from the Tema Harbour are shown in Fig. 5.2. At all the sampling stations, Cd
occurred predominantly in the acid-soluble phase (70-85%), and was divided nearly equally
among the reducible (5-10%), oxidisable (5-12%) and residual (5-10%) phases. Hg also
occurred mainly in the acid-soluble phase (52-67) with relatively higher fractions in the
residual phase (15-42%) than in the reducible (0-15%) and oxidisable (0-14%) phases. At all
the sampling stations, Al (73-83%), Mn (70-80%), Ni (62-72%), Pb (50-65%), Cr (60-76%),
Cu (57-72%), As (52-63%) and Sn (50-100%) were mainly present in the residual phase. For
most of these metals, the fractions in the acid-soluble phase were low, i.e. Al (4-8%), Mn (8-
17%), Ni (8-15%), Pb (5-10%), Cr (3-7%), Cu (3-7%) and As (8-15%). In the case of Sn, no
appreciable fraction was present in the acid-soluble phase at stations S5-S12 in the Main
Harbour, although their fraction was appreciable (17-28%) at the remaining sampling stations.
For Zn, both the reducible (38-45%) and residual (35-42%) phases were the most important at
all the sampling stations, while the oxidisable phase was the least important. Appreciable
fractions of Zn (12-18%) were also present in the acid-soluble phase.
Table 5.3 shows the enrichment factors (EFs) of the investigated metals in the Tema Harbour
sediments. The results show relatively higher enrichment of Cd over the other metals. The Cd
concentrations in the Tema Harbour surface sediments exceeded the average crustal
concentration by over an order of magnitude. The concentrations of Cd, Hg, Pb and As in the
Tema Harbour sediments were 12-41, 2-33, 1-10 and 2-5 times their average crustal
concentrations, respectively. The concentrations of Cu and Zn in the Tema Harbour sediments
were elevated above their average crustal concentrations only in the Canoe Basin and the
Fishing Harbour, while the sediment Sn concentrations exceeded the average crustal
concentration only at stations S1-S4, S13 and S14 in the north-eastern corner of the Main
Harbour, the Canoe Basin and the Fishing Harbour. The concentrations of Mn, Ni and Cr in
the Tema Harbour sediments were about an order of magnitude lower than their average
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
134
Cu (mg/kg)
31 – 54
54 – 78
78 – 101
101 – 124
124 – 147
147 – 171
171 – 194
194 – 217
217 – 241
241 – 264
Zn (mg/kg)
77 – 127
127 – 177
177 – 227
227 – 277
277 – 327
327 – 376
376 – 426
426 – 476
476 – 526
526 – 576
Hg (mg/kg)
0.3 – 0.7
0.7 – 1.1
1.1 – 1.6
1.6 – 2.0
2.0 – 2.4
2.4 – 2.8
2.8 – 3.2
3.2 – 3.7
3.7 – 4.1
4.1 – 4.5
Sn (mg/kg)
1 – 3
3 – 6
6 – 9
9 – 12
12 – 15
15 – 17
17 – 20
20 – 23
23 – 26
26 – 29
Al (mg/kg)
13,900 – 15,200
15,200 – 16,600
16,600 – 18,000
18,000 – 19,300
19,300 – 20,700
20,700 – 22,000
22,000 – 23,400
23,400 – 24,800
24,800 – 26,100
26,100 – 27,500
Pb (mg/kg)
31 – 50
50 – 70
70 – 90
90 – 110
110 – 130
130 – 150
150 – 170
170 – 190
190 – 210
210 – 230
a b
c d
f e
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
135
Mn (mg/kg)
160 – 171
171 – 182
182 – 193
193 – 204
204 – 215
215 – 226
226 – 237
237 – 248
248 – 259
259 – 270
Ni (mg/kg)
19 – 20
20 – 22
22 – 24
24 – 26
26 – 27
27 – 29
29 – 31
31 – 32
32 – 34
34 – 36
Cr (mg/kg)
56 – 61
61 – 67
67 – 72
72 – 77
77 – 83
83 – 88
88 – 94
94 – 99
99 – 105
105 – 110
As (mg/kg)
10 – 11
11 – 12
12 – 13
13 – 14
14 – 15
15 – 17
17 – 18
18 – 19
19 – 20
20 – 21
Cd (mg/kg)
4 – 6
6 – 7
7 – 8
8 – 10
10 – 11
11 – 12
12 – 14
14 – 15
15 – 16
16 – 18
Fig. 5.1 Spatial distribution patterns of (a) Pb, (b) Cu, (c) Zn, (d) Hg, (e) Sn, (f) Al, (g)
Mn, (h) Ni, (i) Cr, (j) As and (k) Cd in surface sediments of Tema Harbour
k
j i
g
h
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
136
crustal concentrations.
The potential elevation of metal concentrations in the Tema Harbour sediments was
confirmed by the geo-accumulation indices (Table 5.3). The geo-accumulation indices
categorised all the Tema Harbour sediments as heavily polluted with respect to Cd, but
unpolluted with respect to the Mn, Ni and Cr concentrations. Sediments of the Canoe Basin
(stations S15-S17) were categorised, based on the geo-accumulation index, as polluted with
respect to the Pb and Zn concentrations, those of the Fishing Harbours (stations S18-S21) as
polluted with respect to the Hg and Cu concentrations, and those of stations S1-S4 in the
north-eastern corner of the Main Harbour as polluted with respect to the Hg concentrations.
5.4. Discussion
5.4.1. Distribution and potential sources of metals in Tema Harbour surface
sediments
This study showed high enrichment of Cd, Hg and As in the Tema Harbour surface sediments
(EFs > 10), which indicates that Cd, Hg and As contamination in the Tema Harbour sediments
is mainly of anthropogenic origin (Chatterjee et al. 2007; Addo et al. 2011; Mahu et al. 2015).
Similarly, the high Pb enrichment in all the sediment samples (except for station S4) suggests
significant anthropogenic inputs of Pb in the Tema Harbour sediments. The EFs of Cu, Zn and
Sn also point to anthropogenic contributions of these metals in various parts of the Tema
Harbour (Table 5.3). The low enrichment of Mn, Ni and Cr in the sediment samples (EFs <
10) indicate that the sources of these metals in the Tema Harbour sediments were mainly from
natural or lithogenic sources, such as weathering and chemical leaching of the bedrock. The
metal enrichment in the Tema Harbour sediments is supported by the geo-accumulation
indices (Igeo) (Table 5.3), which indicate that the Tema Harbour sediments are potentially
contaminated with respect to their Pb, Cu, Zn, As, Cd, Hg and Sn concentrations, while they
are potentially uncontaminated with respect to the Mn, Ni and Cr concentrations.
Potential anthropogenic sources of Pb, Cu, Zn, As, Cd, Hg and Sn contamination in the Tema
Harbour sediments are varied and may relate to bunkering, fueling, discharge of bilge, and
scraping and painting of vessels as well as vehicular traffic, industrial and urban effluent
discharges (Lepland et al. 2010; Mestres et al. 2010; Schipper et al. 2010; Nyarko et al. 2014).
The use of antifouling paints on ships and fishing vessels, for example, is an important source
Table 5.3 Enrichment factors and geo-accumulation indices of measured metals in surface sediments from Tema Harbour, Ghana
Enrichment Factors (EFs)
Geo-accumulation indices (Igeo)
Sampling
station Mn Ni Pb Cr Cu Zn As Cd Hg Sn
Mn Ni Pb Cr Cu Zn As Cd Hg Sn
S1 0.9 1.3 11.2 3.2 6.7 13.4 37.9 172 149 54.7
-2.9 -2.4 0.7 -1.1 0.0 1.0 2.5 4.6 4.4 3.0
S2 1.0 1.6 22.9 3.4 8.2 13.3 32.3 148 153 83.6
-3.1 -2.4 1.4 -1.4 -0.1 0.6 1.9 4.1 4.1 3.3
S3 1.0 1.6 21.2 3.3 8.0 12.9 31.1 219 102 30.9
-3.2 -2.4 1.3 -1.4 -0.1 0.6 1.8 4.6 3.5 1.8
S4 0.9 1.0 8.7 2.2 4.3 7.9 24.9 130 71.1 19.0
-2.4 -2.1 1.0 -1.0 -0.1 0.8 2.5 4.9 4.0 2.1
S5 0.9 1.3 13.0 2.8 3.4 7.6 34.4 173 21.3 1.7
-2.8 -2.3 1.0 -1.2 -0.9 0.2 2.4 4.8 1.7 -1.9
S6 1.0 1.3 14.9 2.9 3.8 8.5 36.8 413 23.3 1.4
-2.9 -2.4 1.1 -1.3 -0.9 0.3 2.4 5.9 1.7 -2.3
S7 1.1 1.7 26.8 3.4 4.5 13.6 32.3 125 29.0 2.0
-3.0 -2.4 1.6 -1.3 -1.0 0.6 1.9 3.8 1.7 -2.1
S8 0.9 1.5 12.2 2.9 2.9 5.1 35.8 184 17.3 1.2
-3.0 -2.2 0.8 -1.2 -1.3 -0.4 2.4 4.7 1.3 -2.6
S9 0.8 1.3 19.6 2.6 3.6 6.8 23.5 199 32.4 1.5
-2.9 -2.3 1.6 -1.3 -0.8 0.1 1.9 4.9 2.3 -2.1
S10 1.0 1.3 26.9 2.9 4.0 6.2 40.7 148 18.4 1.7
-2.8 -2.5 1.9 -1.4 -0.9 -0.2 2.5 4.3 1.3 -2.1
S11 1.1 1.5 25.7 3.6 2.9 9.9 39.7 137 25.4 1.5
-2.8 -2.4 1.8 -1.1 -1.4 0.4 2.4 4.2 1.7 -2.3
S12 0.9 1.6 21.0 2.5 3.0 8.0 31.8 175 45.5 2.0
-2.9 -2.1 1.6 -1.4 -1.2 0.2 2.2 4.7 2.7 -1.7
S13 1.0 1.9 26.0 3.2 5.8 12.1 35.2 118 45.7 29.9
-2.7 -1.6 2.1 -1.0 -0.1 1.0 2.5 4.3 2.9 2.3
S14 1.3 1.8 28.7 3.5 5.9 11.9 41.5 230 42.8 27.6
-2.5 -2.0 2.0 -1.1 -0.3 0.7 2.5 5.0 2.5 1.9
S15 1.3 1.3 95.8 3.7 18.6 42.8 49.2 180 52.1 20.3
-2.6 -2.6 3.6 -1.1 1.2 2.5 2.7 4.5 2.7 1.4
S16 1.3 1.5 88.0 4.1 17.5 42.8 41.5 219 287 18.1
-2.6 -2.4 3.5 -1.0 1.1 2.4 2.4 4.8 5.2 1.2
S17 1.3 1.6 103 3.9 18.1 45.1 52.1 175 334 26.7
-2.8 -2.5 3.5 -1.2 1.0 2.3 2.5 4.3 5.2 1.6
S18 0.2 1.3 44.9 4.8 20.7 32.0 51.1 199 86.4 27.9
-2.4 -2.3 2.8 -0.4 1.7 2.3 3.0 4.9 3.7 2.1
S19 0.8 1.2 30.1 3.3 12.3 22.0 32.0 196 84.7 21.6
-2.5 -1.9 2.7 -0.5 1.4 2.3 2.8 5.4 4.2 2.2
S20 1.2 1.3 37.5 3.9 13.5 24.7 36.8 191 142 17.3
-2.5 -2.4 2.5 -0.7 1.0 1.9 2.5 4.9 4.4 1.4
S21 1.1 1.3 37.9 4.6 14.4 16.6 36.9 172 133 15.5
-2.7 -2.5 2.4 -0.7 1.0 1.2 2.3 4.6 4.2 1.1
Main Harbour (stations S1-S14); Canoe Basin (stations S15-S17); Inner Fishing Harbour (stations S18 and S19); Outer Fishing Harbour (stations
20 and 21). For the interpretations of the EF Igeo values, see Section 5.2.2.
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
138
of Cu and Sn in harbour sediments (Castro et al. 2012; Nyarko et al. 2011). There were
significant correlations among the metals (Table 5.2), which can be attributed to common
sources (Nyarko et al. 2014; Qu and Kelderman 2001) or similar distribution patterns (Aloupi
and Angelidis 2001) of the metals in the Tema Harbour sediments.
Different proximities of sampling stations to local contamination sources in the Tema Harbour
may account for the differences in the sediment metal concentrations across the harbour. For
example, the Tema Harbour has two dry docks located close to stations S1 and S2, where
activities such as sandblasting, high pressure water cleaning, scraping and painting are carried
out. Moreover, station S4 is close to the Oil Berth, where oil tankers berth and carry out
bunkering activities. Thus, the proximity of the north-eastern stations to the dry docks and the
Oil Berth in the Main Harbour may have resulted in the relatively higher Cu, Hg and Sn
concentrations present in the sediments from this area. Higher concentrations of Pb, Cu, Zn
and Hg occurred in the Canoe Basin and the Fishing Harbour, which could be due to oil spills
during refuelling of fishing vessels in these areas.
Moreover, the Main Harbour is frequently dredged, whereas the Fishing Harbour and Canoe
Basin are not. Dredging in the Main Harbour may potentially remove contaminated surficial
sediments and result in reduced metal levels, whereas the accumulation of sediments in the
Canoe Basin and the Fishing Harbour may result in elevated concentrations of associated
metals. The resuspension and redistribution of bottom sediment due to e.g. tidal currents,
dredging and ship movements (Lepland et al. 2010) may also contribute to the spatial
variations in the sediment metal concentrations in the Tema Harbour.
Since bulk sediments were analysed in this study, a correlation analysis was performed to
examine the associations between the metal concentrations and sediment characteristics.
Significant correlations were observed between the silt-clay content and the Cu, Zn, Sn, Mn,
Ni, Cr and As concentrations in the Tema Harbour sediments (Table 5.2), which can be
attributed to the high affinity of metals for the fine fractions of sediments owing to their large
surface areas (Aloupi and Angelidis 2001; Kelderman and Osman 2007; Lepland et al. 2010;
Nyarko et al. 2011). The distribution patterns of Cu, Zn, Sn, Mn, Ni, Cr and As in the Tema
Harbour sediments (Fig. 5.1) may, therefore, be influenced by the differences in their silt-clay
content. As a geochemical substrate for metals (Aloupi and Angelidis 2001), TOC may also
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
139
play a role in the metal distribution, which may explain its correlations with Mn, Ni and Cu
(Table 5.2).
Carbonate generally has a low capacity to adsorb and retain metals and is, therefore,
considered as a diluent of metal concentrations in sediments (Horowitz 1985; Aloupi and
Angelidis 2001). Thus, Aloupi and Angelidis (2001) found an inverse relationship between
the metal and carbonate concentration of the Mytilene Harbour sediments. The Tema Harbour
sediments had a nearly uniform carbonate content (Table 5.1), exhibiting generally poor
correlations with the metal concentrations in the harbour sediments (Table 5.2). Al is known
to distribute nearly equally between the fine and coarse fractions of a sediment (Aloupi and
Angelidis 2001), which may explain the observed poor correlation between the Al
concentration and the silt-caly fraction of the habour sediments (Table 5.2).
The mean metal concentrations from this study were compared with previous studies in 2000
by JICA (Japan International Co-operation Agency) and 2010-2011 by Nyarko et al. (2014)
(Table 5.1). Table 5.1 shows that the current mean Pb, As and Cd concentrations are higher
than the levels in 2000, whereas the current concentrations of Cr and Hg are lower than the
2000 levels. Moreover, the current mean levels of Mn, Cr, Cu, Zn and As are higher than the
levels in 2010-2011. The mean reported concentrations of Ni and Cd in 2010-2011 were,
however, higher than the current levels. These comparisons did not reveal a progressive
increase in metal contamination of Tema Harbour sediments since the year 2000.
5.4.2. Metal fractionation in the Tema Harbour sediments
The negative Eh values of the bottom water (Table 5.1) indicate anoxic bottom conditions in
the Tema Harbour (Matijević et al. 2007), which has also been observed in previous studies
(Botwe et al. 2017a; Botwe et al. 2017b). Metal fractionation in the Tema Harbour sediments
(Fig. 5.2) showed that most of the metals (Al, Mn, Ni, Pb, Cr, Cu, As and Sn) were
predominantly present in the residual phase, where they are incorporated into the crystal
lattice (Calmano et al. 1993; Kelderman and Osman 2007). Among the non-residual fractions,
the oxidisable phase was most important for Pb, Cr, Cu and As. This indicates that
complexation with organic matter and precipitation with sulphides were the main mechanisms
for the immobilisation of Pb, Cr, Cu and As into the Tema Harbour sediments, which is the
case for most metals under anoxic conditions (Caille et al. 2003; Ho et al. 2012a).
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
140
Mn and Sn were mainly present in the acid-soluble phase, while Al and Ni were distributed
nearly equally between the non-residual phases. The fractionation of Zn showed that the
reducible phase was most important. This suggests that co-precipitation with oxides or
hydroxides of Fe and Mn was a main mechanism for Zn immobilisation into the Tema
Harbour sediments. Cd (70-85%) and Hg (52-67%) were predominantly associated with the
acid-soluble phase. In this phase, Hg may associate with carbonates, which may partly explain
the observed correlation between Hg and carbonate (Table 5.2).
5.4.3. Ecological implications of metal contamination in Tema Harbour sediments
5.4.3.1. Ecotoxicological implications
Metal contamination in sediments may cause toxicity in sediment-dwelling organisms (Long
et al. 1995; Long et al. 2006). The effects-range low (ERL) and effects-range median (ERM)
sediment quality guidelines (Long et al. 1995) were used to characterise the potential toxicity
of the Tema Harbour sediments due to their metal (Ni, Pb, Cr, Cu, Zn, As, Cd and Hg)
contamination. Metal concentrations below the ERL, at or above the ERL but below the ERM,
and at or above the ERM are associated with, respectively, rare, occasional, and frequent
occurrence of toxic effects (Long et al. 1995). For each metal, two quotients namely the
effects-range low qoutient (ERLQ) and effects-range median quotient (ERMQ) were derived
by dividing the measured metal concentration by its corresponding ERL and ERM
concentrations, respectively (Long et al. 2006). Within this approach, an ERLQ < 1 indicates
toxic effects will rarely occur; an ERLQ ≥ 1 but ERMQ < 1 indicates toxic effects will occur
occasionally; whereas an ERMQ ≥ 1 indicates toxic effects will occur frequently.
The ERLQ and ERMQ values (Table 5.4) indicate that Hg concentrations at most (67%) of
the sampling stations may potentially cause frequent occurrence of toxic effects. Thus, Hg is
of potential concern in the Tema Harbour, particularly in the north-eastern corner of the Main
Harbour, the Canoe Basin and the Fishing Harbour. Frequent occurrence of toxic effects is
also expected as a result of the sediment Zn concentrations in the Canoe Basin and the Fishing
Harbour. There are also isolated areas in the Tema Harbour where the concentrations of Pb
and Cd in the sediments may be associated with frequent occurrence of toxic effects. At most
of the stations, however, there is a potential for occasional occurrence of toxic effects as a
Table 5.4 Calculated effects-range low quotients (ERLQ), effects-range median quotients (ERMQs) and mean ERM quotients
(mERMQs) for measured metals in surface sediments from Tema Harbour, Ghana. The ERL and ERM values for the measured
metals are also presented.
MH = Main Harbour; CB = Canoe Basin; IFH = Inner Fishing Harbour; OFH = Outer Fishing Harbour
ERLQ
ERMQ
Harbour
area
Sampling
station Ni Pb Cr Cu Zn As Cd Hg
Ni Pb Cr Cu Zn As Cd Hg
mERMQ
MH S1 1.0 0.7 0.9 2.4 1.4 1.8 6.3 17.3
0.4 0.1 0.2 0.3 0.5 0.2 0.8 3.7
0.8
S2 1.0 1.1 0.7 2.3 1.1 1.2 4.3 14.0
0.4 0.2 0.2 0.3 0.4 0.1 0.5 3.0
0.6
S3 1.0 1.0 0.7 2.2 1.0 1.2 6.3 9.3
0.4 0.2 0.2 0.3 0.4 0.1 0.8 2.0
0.5
S4 1.3 0.8 0.9 2.3 1.2 1.8 7.3 12.7
0.5 0.2 0.2 0.3 0.5 0.2 0.9 2.7
0.7
S5 1.1 0.8 0.8 1.3 0.8 1.8 6.8 2.7
0.4 0.2 0.2 0.2 0.3 0.2 0.8 0.6
0.4
S6 1.0 0.9 0.8 1.3 0.9 1.7 14.8 2.7
0.4 0.2 0.2 0.2 0.3 0.2 1.8 0.6
0.5
S7 1.0 1.2 0.7 1.3 1.1 1.2 3.6 2.7
0.4 0.3 0.2 0.2 0.4 0.1 0.4 0.6
0.3
S8 1.2 0.7 0.8 1.0 0.5 1.7 6.7 2.0
0.5 0.2 0.2 0.1 0.2 0.2 0.8 0.4
0.3
S9 1.1 1.2 0.8 1.4 0.7 1.2 7.7 4.0
0.4 0.3 0.2 0.2 0.3 0.1 1.0 0.8
0.4
S10 1.0 1.5 0.7 1.3 0.6 1.8 5.0 2.0
0.4 0.3 0.2 0.2 0.2 0.2 0.6 0.4
0.3
S11 1.0 1.4 0.9 0.9 0.9 1.7 4.5 2.7
0.4 0.3 0.2 0.1 0.3 0.2 0.6 0.6
0.3
S12 1.2 1.2 0.7 1.1 0.8 1.5 6.4 5.3
0.5 0.3 0.2 0.1 0.3 0.2 0.8 1.1
0.4
S13 1.7 1.7 1.0 2.3 1.4 1.9 4.8 6.0
0.7 0.4 0.2 0.3 0.5 0.2 0.6 1.3
0.5
S14 1.3 1.6 0.9 2.0 1.1 1.9 7.8 4.7
0.5 0.3 0.2 0.2 0.4 0.2 1.0 1.0
0.5
CB S15 0.9 4.9 0.9 5.8 3.8 2.1 5.8 5.3
0.4 1.1 0.2 0.7 1.4 0.2 0.7 1.1
0.7
S16 1.0 4.4 1.0 5.3 3.7 1.7 6.8 28.7
0.4 0.9 0.2 0.7 1.4 0.2 0.9 6.1
1.3
S17 1.0 4.6 0.8 4.9 3.5 1.9 4.9 30.0
0.4 1.0 0.2 0.6 1.3 0.2 0.6 6.3
1.3
IFH S18 1.1 2.8 1.4 7.8 3.5 2.6 7.7 10.7
0.4 0.6 0.3 1.0 1.3 0.3 1.0 2.3
0.9
S19 1.5 2.6 1.3 6.5 3.3 2.3 10.6 14.7
0.6 0.6 0.3 0.8 1.2 0.3 1.3 3.1
1.0
OFH S20 1.0 2.3 1.1 5.0 2.6 1.8 7.3 17.3
0.4 0.5 0.2 0.6 1.0 0.2 0.9 3.7
0.9
S21 1.0 2.1 1.2 4.8 1.6 1.7 5.9 14.7
0.4 0.4 0.3 0.6 0.6 0.2 0.7 3.1
0.8
ERL 20.9 46.7 81 34 150 8.2 1.2 0.15
- - - - - - - -
-
ERM 51.6 218 370 270 410 70 9.6 0.71
- - - - - - - -
-
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
142
result of Ni, Pb, Cu, As and Cd concentrations in the sediments, while the Cr concentrations
are not likely to cause toxic effects based on the ERLQ and ERMQ values (Table 5.4).
To characterise the overall potential sediment toxicity due to a mixture of metals, mean ERM
quotients (mERMQs) were calculated by averaging the different metal ERMQs with the toxic
effects (Long et al. 2006; Birch and Hutson 2009). The overall potential toxicity is classified
as minimal if the mERMQ < 0.1, low if 0.1 ≤ mERMQ < 0.5, moderate if 0.5 ≤ mERMQ <
1.5 and high if mERMQ > 1.5 (Birch and Hutson 2009). The mERMQ values of the Tema
Harbour sediments (Table 5.4) indicate that metal concentrations of the sediments from the
north-eastern stations in the Main Harbour, the Canoe Basin and the Fishing Harbour may
cause moderate toxicity to benthic organisms, while sediments from the remaining areas may
be associated with low toxicity.
5.4.3.2. Ecological risk implications
Metal fractionation in sediments significantly determines their potential mobility and
availability for uptake by benthic organisms (Calmano et al. 1993; Jain 2004; Pini et al.
2015). Metals associated with the acid-soluble phase have the greatest mobility and
bioavailability potential and pose the greatest ecological risk, whereas those in the residual
phase have the least mobility and bioavaility potential and pose the least ecological risk
(Calmano et al. 1993; Jain 2004; Kelderman and Osman 2007; Iqbal et al. 2013; Ho et al.
2012a). A risk assessment code (RAC) has therefore been developed based on the fraction
(%) of metal associated with the acid-soluble phase to characterise the potential risk of
sediment-associated metals entering the food chain as follows (Jain 2004): acid-soluble
fraction <1 % indicates no risk, 1-10 % indicates low risk, 11-30 % indicates medium risk,
31-50% indicates high risk, and >50 % indicates very high risk.
The phase distributions of the investigated metals in the Tema Harbour sediments (Fig. 5.2)
show large fractions of Cd (70-85%) and Hg (52-67) in the acid-soluble phase, indicating that
Cd and Hg contamination in the Tema Harbour sediments may pose very high ecological
risks. Sn may pose medium risk at stations 1-4 in the Main Harbour, the Canoe Basin (stations
15-17) and the Fishing Harbour (stations 18-21), where the acid-soluble fraction ranged
between 17 and 28%, but poses no risk at the remaining stations. The fractions of Mn (8-
17%), Ni (8-15%), Zn (12-18%) and As (8-15%) in the acid-soluble phase indicate these
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
143
0
20
40
60
80
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f A
l (%
)
Sampling station within Tema Harbour
a
0
10
20
30
40
50
60
70
80
90
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f M
n (
%)
Sampling station within Tema Harbour
b
0
20
40
60
80
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f N
i (%
)
Sampling station within Tema Harbour
c
0
20
40
60
80
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f P
b (
%)
Sampling station within Tema Harbour
d
0
20
40
60
80
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f C
u (
%)
Sampling station within Tema Harbour
f
0
20
40
60
80
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f C
r (%
)
Sampling station within Tema Harbour
e
Legend:
Residual phase
Oxidisable phase
Reducible phase
Acid-soluble phase
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
144
0
10
20
30
40
50
60
70
80
90
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f Z
n (
%)
Sampling station within Tema Harbour
g
0
20
40
60
80
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f A
s (
%)
Sampling station within Tema Harbour
h
0
20
40
60
80
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f C
d (
%)
Sampling station within Tema Harbour
i
0
20
40
60
80
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f H
g (
%)
Sampling station within Tema Harbour
j
Fig. 5.2 Distribution of metals over the acid-soluble, reducible, oxidisable and
residual phases of Tema Harbour sediments: (a) Al, (b) Mn, (c) Ni, (d) Pb, (e) Cr, (f)
Cu, (g) Zn, (h) As, (i) Cd, (j) Hg, and (k) Sn
Legend:
Residual phase
Oxidisable phase
Reducible phase
Acid-soluble phase
0
20
40
60
80
100
1 3 5 7 9 11 13 15 17 19 21
Phase d
isdtr
ibution o
f S
n (
%)
Sampling station within Tema Harbour
k
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
145
metals pose low-medium risks, while those of Pb (5-10%), Cr (3-7%) and Cu (3-7%) present
low risk. The non-residual or labile (i.e. acid-soluble + reducible + oxidisable) fractions,
however, constitute a pool of potentially bioavailable metals due to their potential to undergo
changes under varying environmental conditions such as pH, Eh and resuspension of bottom
sediments (Calmano et al. 1993; Kelderman and Osman 2007; De Jonge et al. 2012; Dung et
al. 2013; Hamzeh et al. 2014; Pini et al. 2015). The considerable fractions of Mn (20-30%),
Ni (28-38%), Pb (35-50%), Cr (24-40%), Cu (28-43%), As (37-48%) and Sn (0-50%) present
in the labile phase, therefore, have implications for their potential ecological risks.
5.4.4. Chemical stability of Tema Harbour sediments
The pH range of the Tema Harbour sediments (7.3-8.3; Table 5.1) indicates that all the
investigated sediments were slightly alkaline. The buffer intensities of the Tema Harbour
sediments ranged from intermediate to strong (Table 5.1). Thus, in general, the Tema Harbour
sediments are potentially stable against small changes in pH, with the potential to lower the
risk of metal remobilisation and exposure due to acidification. A reduction in pH
(acidifcation) can substantially increase the risk of metal exposure to organisms via
remobilisation of sediment-associated metals (Calmano 1988; Calmano et al. 1993;
Kelderman and Osman 2007; Ho et al. 2012a). The potential ecological risk of metal
remobilisation due to acidification may be more pronounced in weakly buffered sediments,
since they have a low capacity to resist slight changes in pH.
The carbonate content is a major determinant of the buffer intensity of sediments: sediments
with carbonate contents >10% are well buffered against acidification over a wide range
(Calmano 1988). The carbonate contents of the Tema Harbour sediments were close to 10
(Table 5.1) and exhibited no significant correlation with the buffer intensity (Table 5.2). The
observed significant correlations between buffer intensity and Cr, Zn, As and Sn
concentrations in the Tema Harbour sediments indicate that increasing buffer intensity
enhances the immobilisation and accumulation of these metals in the harbour sediments. The
significant correlation between buffer intensity and silt-clay content (Table 5.2) suggests that
the silt-clay content has a positive influence on the buffer intensity of the Tema Harbour
sediments, possibly due to the effect of alumino silicates, which are another major
determinant of the sediment buffer intensity (Calmano 1988).
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
146
5.5. Conclusions
The metal (Al, Mn, Ni, Pb, Cr, Cu, Zn, As, Cd, Hg and Sn) distribution, fractionation and
their ecological implications of surface sediments from the Tema Harbour (Greater Accra,
Ghana) have been investigated. Sediment concentrations of Mn, Ni, Cr, Cu, Zn, As and Sn
differed significantly across the Tema Harbour. Cd, Hg, Pb, Cu, Zn, As and Sn were enriched
in the Tema Harbour sediments and may have been derived mainly from anthropogenic
sources. As the Tema Harbour is located in an industrial area, potential anthropogenic sources
of metals in the harbour include industrial effluent discharges as well as vehicular emissions.
Moreover, metal contamination in the Tema Harbour may originate from shipping and fishing
activities such as the use of antifouling paints on ships and fishing vessels, oil spills,
discharge of bilge, and scraping and painting of vessels. On the other hand, Mn, Ni and Cr
were not enriched in the Team Harbour sediments and may, therefore, be of lithogenic origin.
Al, Mn, Ni, Pb, Cr, Cu, As and Sn were present mainly in the residual phase, Cd and Hg
associated mainly with the exchangeable phase, while the reducible phase was most important
for Zn. Based on the metal fractionation in the sediments, Cd and Hg may pose high potential
risks of entering the food chain; Mn, Ni, Zn, As and Sn may pose low-medium potential risks
of entering the food chain, while Pb, Cr, and Cu pose low potential risks of entering the food
chain. A screenining-level ecotoxicological evaluation of the sediment metal concentrations
with reference to biological effect-based sediment quality guidelines indicated that Hg may be
associated with high toxicity and should, therefore, be of potential concern. Pb, Cu, Zn, As
and Cd concentrations may also induce appreciable toxicity.
References
Addo M, Okley G, Affum H, Acquah S, Gbadago J, Senu J, Botwe BO (2011) Water quality
and level of some heavy metals in water and sediments of Kpeshie Lagoon, La-Accra,
Ghana. Res J Environ Earth Sci 3:487-497.
Aloupi M, Angelidis M (2001) Geochemistry of natural and anthropogenic metals in the
coastal sediments of the island of Lesvos, Aegean Sea. Environ Pollut 113:211-219.
Birch GF, Hutson P (2009) Use of sediment risk and ecological/conservation value for
strategic management of estuarine environments: Sydney estuary, Australia. Environ
Manage 44:836-850.
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
147
Botwe BO, Kelderman P, Nyarko E, Lens PNL (2017a) Assessment of DDT, HCH and PAH
Contamination and Associated Ecotoxicological Risks in Surface Sediments of
Coastal Tema Harbour (Ghana). Mar Pollut Bull 115: 480-488
Botwe BO, Schirone A, Delbono I, Barsanti M, Delfanti R, Kelderman P, Nyarko E, Lens
PNL (2017b) Radioactivity concentrations and their radiological significance in
sediments of the Tema Harbour (Greater Accra, Ghana). J Radiat Res Appl Sci 10:63-
71.
Burton GA (2002) Sediment quality criteria in use around the world. Limnology 3:65-76.
Caille N, Tiffreau C, Leyval C, Morel JL (2003) Solubility of metals in an anoxic sediment
during prolonged aeration. Sci Total Environ 301:239-250.
Calmano W (1988) Stabilization of dredged mud. Environmental Management of Solid
Waste, Springer, Berlin, pp 80-98
Calmano W, Hong J, Foerstner U (1993) Binding and mobilization of heavy metals in
contaminated sediments affected by pH and redox potential. Water Sci Technol
28:223-223.
Casado-Martínez MC., Buceta JL, Belzunce MJ, DelValls TA (2006) Using sediment quality
guidelines for dredged material management in commercial ports from Spain. Environ
Int 32:388-396.
Castro ÍB, Arroyo MF, Costa PG, Fillmann G (2012) Butyltin compounds and imposex levels
in Ecuador. Arch Environ Contam Toxicol 62:68-77.
Chatterjee M, Silva Filho EV, Sarkar SK, Sella SM, Bhattacharya A, Satpathy KK, Prasad
MVR, Chakraborty S, Bhattacharya BD (2007) Distribution and possible source of
trace elements in the sediment cores of a tropical macrotidal estuary and their
ecotoxicological significance. Environ Int 33:346-356.
De Jonge M, Teuchies J, Meire P, Blust R, Bervoets L (2012) The impact of increased oxygen
conditions on metal-contaminated sediments part I: Effects on redox status, sediment
geochemistry and metal bioavailability. Water Res 46:2205-2214.
Di Palma L, Mecozzi R (2007) Heavy metals mobilization from harbour sediments using
EDTA and citric acid as chelating agents. Journal of hazardous materials 147:768-775.
Dung TTT, Cappuyns V, Swennen R, Phung NK (2013) From geochemical background
determination to pollution assessment of heavy metals in sediments and soils. Rev
Environ Sci Bio/Technol 12:335-353.
Hamzeh M, Ouddane B, Daye M, Halwani J (2014) Trace Metal Mobilization from Surficial
Sediments of the Seine River Estuary. Water Air Soil Pollut 225:1878-1892.
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
148
Ho HH, Swennen R, Cappuyns V, Vassilieva E, Van Gerven T, Van Tran T (2012a) Potential
release of selected trace elements (As, Cd, Cu, Mn, Pb and Zn) from sediments in Cam
River-mouth (Vietnam) under influence of pH and oxidation. Sci Total Environ
435:487-498.
Ho HH, Swennen R, Cappuyns V, Vassilieva E, Van Tran T (2012b) Necessity of
normalization to aluminum to assess the contamination by heavy metals and arsenic in
sediments near Haiphong Harbor, Vietnam. J Asian Earth Sci 56:229-239.
Horowitz AJ (1985) A primer on trace metal-sediment chemistry, U.S. Geological Survey
Water-Supply Paper 2277, 67 p
Iqbal J, Tirmizi S, Shah M (2013) Statistical apportionment and risk assessment of selected
metals in sediments from Rawal Lake (Pakistan). Environ Monit Assess 185:729-743.
Jain C (2004) Metal fractionation study on bed sediments of River Yamuna, India. Water Res
38:569-578.
JICA (Japan International Co-operation Agency) Draft Environmental Impact Statement for
Short-Term Development Plan of Tema Port
(http://open_jicareport.jica.go.jp/pdf/11681632_03.pdf). Accessed 11 January 2017
Kelderman P, Osman A (2007) Effect of redox potential on heavy metal binding forms in
polluted canal sediments in Delft (The Netherlands). Water Res 41:4251-4261.
Lepland A, Andersen TJ, Lepland A, Arp HPH, Alve E, Breedveld GD, Rindby A (2010)
Sedimentation and chronology of heavy metal pollution in Oslo harbor, Norway. Mar
Pollut Bull 60:1512-1522.
Long ER, Ingersoll CG, MacDonald DD (2006) Calculation and uses of mean sediment
quality guideline quotients: a critical review. Environ Sci Technol 40:1726-1736.
Long ER, MacDonald DD, Smith SL, Calder FD (1995) Incidence of adverse biological
effects within ranges of chemical concentrations in marine and estuarine sediments.
Environ Manage 19: 81-97.
Mahu E, Nyarko E, Hulme S, Coale KH (2015) Distribution and enrichment of trace metals in
marine sediments from the Eastern Equatorial Atlantic, off the Coast of Ghana in the
Gulf of Guinea. Mar Pollut Bull 98:301-307.
Matijević S, Kušpilić G, Kljaković-Gašpić Z (2007) The redox potential of sediment from the
Middle Adriatic region. Acta Adriatica, 48:191-204.
Mestres M, Sierra J, Mösso C, Sánchez-Arcilla A (2010) Sources of contamination and
modelled pollutant trajectories in a Mediterranean harbour (Tarragona, Spain). Mar
Pollut Bull 60:898-907.
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
149
Nyarko E, Botwe BO, Lamptey E, Nuotuo O, Foli BA, Addo MA (2011) Toxic metal
concentrations in deep-sea sediments from the jubilee oil field and surrounding areas
off the western coast of Ghana. Trop Environ Res 9:584-595.
Nyarko E, Fletcher A, Addo S, Foli BAK, Mahu E (2014) Geochemical Assessment of Heavy
Metals in Surface Sediments: A Case Study of the Tema Port, Ghana. J Shipping
Ocean Eng 4:79-92.
Phillips CR (2007) Sediment contaminant patterns within coastal areas of the Southern
California Bight: multivariate analyses of Bight'98 Regional Monitoring Data. Bull
Southern California Acad Sci 106:163-178.
Pini J, Richir J, Watson G (2015) Metal bioavailability and bioaccumulation in the polychaete
Nereis (Alitta) virens (Sars): The effects of site-specific sediment characteristics. Mar
Pollut Bull 95:565-575.
Pozza MR, Boyce JI, Morris WA (2004) Lake-based magnetic mapping of contaminated
sediment distribution, Hamilton Harbour, Lake Ontario, Canada. J Appl Geophysics
57:23-41.
Pueyo M, Rauret G, Lück D, Yli-Halla M, Muntau H, Quevauviller P, Lopez-Sanchez J
(2001) Certification of the extractable contents of Cd, Cr, Cu, Ni, Pb and Zn in a
freshwater sediment following a collaboratively tested and optimised three-step
sequential extraction procedure. J Environ Monit 3:243-250.
Qu W, Kelderman P (2001) Heavy metal contents in the Delft canal sediments and suspended
solids of the River Rhine: multivariate analysis for source tracing. Chemosphere
45:919-925.
Quevauviller P, Rauret G, López-Sánchez JF, Rubio R, Ure A and Muntau H (1997)
Certification of trace metal extractable contents in a sediment reference material
(CRM 601) following a three-step sequential extraction procedure. Sci Total Environ
205:223-234.
Schipper C, Rietjens I, Burgess R, Murk A (2010) Application of bioassays in toxicological
hazard, risk and impact assessments of dredged sediments. Mar Pollut Bull 60:2026-
2042.
Schumacher BA (2002) Methods for the determination of total organic carbon (TOC) in soils
and sediments. Ecological Risk Assessment Support Center, p1-23.
Taylor S (1964) Abundance of chemical elements in the continental crust: a new table.
Geochim Cosmochim Acta 28:1273-1285.
Metal Distribution and Fractionation in Surface Sediments of Coastal Tema Harbour (Ghana) and its Ecological Implications
150
Wang X-C, Zhang Y-X, Chen RF (2001) Distribution and partitioning of polycyclic aromatic
hydrocarbons (PAHs) in different size fractions in sediments from Boston Harbor,
United States. Mar Pollut Bull 42:1139-1149.
Chapter 6
Integrated Hazard, Risk and
Impact Assessment of Tropical
Marine Sediments from Tema
Harbour (Ghana)
A modified version of this chapter was published as: Botwe, B.O., De Schamphelaere, K.,
Schipper, C.A., Teuchies, J., Blust, R., Nyarko, E., & Lens, P.N.L. (2017). Integrated hazard,
risk and impact assessment of tropical marine sediments from Tema Harbour (Ghana).
Chemosphere, 177, 24-34.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
152
Abstract
The potential ecological hazard, risk and impact of tropical marine sediments from the Tema
Harbour (Greater Accra, Ghana) was investigated by integrating Corophium volutator and
Hediste diversicolor whole-sediment toxicity bioassays with data on the metals (Cd, Pb, Cr,
Ni, Cu, Zn and As) concentrations of the sediments. The whole-sediment toxicity bioassay
results showed that sediments of the Tema Harbour are potentially hazardous to marine
benthic invertebrates. C. volutator exhibited a higher vulnerability to the sediment toxicity
than H. diversicolor, although the latter showed higher biota-sediment accumulation factors
for the investigated metals. Statistically significant correlations were observed between C.
volutator mortality and sediment Cd concentration (r = 0.84, p < 0.05; n = 6) and between H.
diversicolor mortality and sediment Cu concentration (r = 0.94, p < 0.05; n = 5). Comparison
of metal concentrations with international action levels for contaminated sediment disposal
indicates that the Tema Harbour sediments contain potentially hazardous concentrations of Cu
and Zn. This study shows that sediments from the Tema Harbour are not suitable for disposal
at sea without remediation. There is, therefore, a need to improve environmental management
and regulate the disposal of dredged material originating from the Tema Harbour.
6.1. Introduction
Contaminated sediments can be a source of hazardous contaminants to aquatic organisms,
particularly benthic species (Burgess et al., 2007; Birch & Hutson, 2009). These benthic
organisms play important roles in the functioning of aquatic ecosystems, such as
biogeochemical cycling (Durou et al., 2007) and as a source of food for other species in the
aquatic food chain (Burton Jr, 2002; Birch & Hutson, 2009; Carvalho et al., 2012; Gaion et
al., 2014). The impact of contaminated sediments on benthic organisms can thus have serious
consequences for the entire food chain (Burton Jr, 2002; Gaion et al., 2014) and the proper
functioning of aquatic ecosystems. Consequently, sediment contamination is a major issue
and information on the associated potential adverse ecological impact is of great interest to
environmental regulators (Birch & Hutson, 2009; Schipper et al., 2010). Several biological
effect-based sediment quality guidelines (SQGs) have been developed as predictive tools for
assessing the potential of contaminated sediments to cause adverse biological effects (Burton
Jr, 2002; Long et al., 2006; Schipper et al., 2013).
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
153
The abilities of SQGs to predict adverse biological effects associated with contaminated
sediments are, however, limited since SQGs do not account for: (1) contaminant
bioavailability (Schipper et al., 2010); (2) synergistic or antagonistic effects of contaminant
mixtures present in sediments under natural conditions (Ciarelli et al., 1998; Forrester et al.,
2003; Eisentraeger et al., 2004; Schipper et al., 2010); (3) multiple effects that may be
exhibited by a single contaminant (Eggen et al., 2004); (4) chronic effects that may result
from long-term exposure to low concentrations of contaminants in sediments (Eggen et al.,
2004) and (5) contaminants present in sediments without being measured or identified as toxic
or hazardous substances (Eisentraeger et al., 2004; Burgess et al., 2007). Consequently,
whole-sediment toxicity bioassays have been recommended for the ecotoxicological
characterisation of contaminated sediments to overcome the limitations of the SQG approach
(Annicchiarico et al., 2007; Ré et al., 2009; Schipper et al., 2010). Whole-sediment toxicity
bioassays involve the exposure of pollution-sensitive benthic invertebrates to contaminated
sediments under laboratory conditions (Forrester et al., 2003). Integrating whole-sediment
bioassays with the SQG approach can provide valuable insight into contaminants potentially
contributing to sediment toxicity.
Marine benthic invertebrates such as C. volutator (Stronkhorst et al., 2003; Scarlett et al.,
2007; van den Heuvel-Greve et al., 2007; Mayor et al., 2008) and H. diversicolor (Moreira et
al., 2006; Mayor et al., 2008) are often employed as bio-indicators of pollution in marine and
estuarine whole-sediment toxicity bioassays. Preference for C. volutator is due to its ease of
collection and maintenance under laboratory conditions, availability in the field throughout
the year, and tolerance to a wide range of salinities, sediment grain sizes and organic carbon
contents (Ciarelli et al., 1998; Roddie & Thain, 2002; Scaps, 2002; Bat, 2005). H. diversicolor
commonly occurs in intertidal areas, is able to survive in hypoxic and contaminated
environments and exhibits tolerance to wide fluctuations in salinity and temperature (Scaps,
2002; Philippe et al., 2008). Both C. volutator and H. diversicolor have wide geographic
distributions across polar, temperate and tropical marine regions (Bat, 2005; Moreira et al.,
2006; Uwadiae, 2010; Carvalho et al., 2012). However, standard whole-sediment toxicity
bioassay protocols have been developed mainly with temperate C. volutator (Roddie & Thain
2002; Schipper et al., 2006) and H. diversicolor (Hannewijk et al., 2004) with mortality as
toxic response (endpoint), whereas whole-sediment toxicity bioassays with tropical species
are not well developed (Adams and Stauber, 2008). Therefore, studies on the use of C.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
154
volutator and H. diversicolor bioassays to assess the toxicity of sediments from tropical
marine environments are scarce.
With over 50% of the world‘s population living in coastal zones (Petrosillo et al., 2009), the
coastal marine environment is characterised by intense anthropogenic activities such as waste
disposal, crude oil extraction and oil spills, shipping, fishing, agriculture and industrialisation
(Petrosillo et al., 2009; Lepland et al., 2010; Schipper et al., 2010). This is also the case for
the tropical marine Tema Harbour in Greater Accra (Ghana). Anthropogenic activities are a
source of a wide range of hazardous substances, which adversely impact organisms inhabiting
the coastal marine environment (Petrosillo et al., 2009; Lepland et al., 2010; Schipper et al.,
2010): previous studies have shown that sediments of the Tema Harbour are contaminated by
polycyclic aromatic hydrocarbons and organochlorine pesticide residues (Botwe et al., 2017)
and metals (Nyarko et al., 2014; Botwe et al., unpublished results). Since Tema Harbour
sediments are dredged periodically with subsequent disposal/storage under seawater,
assessment of sediment quality is required to guide sediment management decisions at Tema
Harbour and minimise adverse ecological impact. Therefore, the objectives of this study were
to investigate: (1) the overall potential toxicity (hazard) of Tema Harbour sediments, (2) the
potential risk (toxicity and bioavailability) of metal contamination in the sediments and (3) the
potential impact (bioaccumulation) of metal contamination in the Tema Harbour sediments on
benthic invertebrates by integrating whole-sediment toxicity bioassays with metal
contamination data.
6.2. Materials and methods
6.2.1. Study area
The Tema Harbour in Greater Accra (Ghana) is a semi-enclosed coastal marine harbour with
a water area of approximately 2 km2, which forms part of the Gulf of Guinea (Fig. 6.1). The
salinity of the Tema Harbour water ranges from 30 to 35 ‰. The Tema Harbour is
compartmentalised into a Main Harbour, an Inner Fishing Harbour, an Outer Fishing Harbour
and a Canoe Basin, which are bound to experience different anthropogenic impacts. The Main
Harbour, the Inner Fishing Harbour and the Canoe Basin have been in operation since 1962,
while the Outer Fishing Harbour was constructed in 1965. Various ships including oil tankers,
bulk carriers, general cargo ships and containerships call at the Main Harbour. The Fishing
Harbour provides handling facilities for semi-industrial and industrial fishing vessels such as
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
155
Fig. 6.1 Map of Tema Harbour showing the sampling stations of grab sediments (1-
30). Grab sediments were composited into five samples for analysis as follows:
sediment sample MH1 = grabs 1-6; MH2 = grabs 7-12; OFH = grabs 13-18; IFH =
grabs 19-24 and CB = grabs 25-30.
trawlers, tuna vessels, and deep-sea carriers, while the Canoe Basin is a dedicated artisanal
canoe fishing landing site. To ensure safe navigation, the Main Harbour is subject to dredging
since 1998, whereas the Canoe Basin was dredged in May 2013. No dredging has yet been
conducted in the Fishing Harbour. Located within an industrial setting, the Tema Harbour is
subject to contamination not only from maritime operations (e.g. bunkering and refuelling,
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
156
maintenance and repairs of vessels), but also from industrial activities (e.g. wastewater
discharges into the harbour).
6.2.2. Sediment sampling
Grab sediment samples were collected from thirty stations (1-30) within the Tema Harbour
(Fig. 6.1) in January 2016 using a stainless steel 3.5 L Ekman grab. The grab samples were
composited to obtain five samples for analysis. In the Main Harbour, grabs 1-6 were
composited to form sample MH1, while grabs 7-12 formed sample MH2. All grabs from the
Outer Fishing Harbour (13-18) were composited into sample OFH, grabs from the Inner
Fishing Harbour (19-24) formed sample IFH, while grabs from the Canoe Basin (25-30)
formed sample CB (Fig. 6.1). All composite samples were mixed thoroughly with a plastic
shovel in acid-washed plastic bowls before taking about 3.5 L portions into 3.78 L
FoodSaver® zipper bags. All the samples were sealed air-tight using a hand-held vacuum
pump and kept on ice in an ice-cool box in the field and during transportation to the Marine
and Fisheries Department laboratory at the University of Ghana (Accra, Ghana), where they
were stored overnight in a refrigerator at 4 oC. The samples were kept chilled in an ice-cool
box and transported by air to the Systemic Physiological and Ecotoxicological Research
laboratory (SPHERE) at the University of Antwerp (Belgium). The samples were kept there in
a cold room at 4 oC until the bioassay experiments were conducted within 2 weeks of sample
collection (Roddie & Thain, 2002).
6.2.3. Sampling of test organisms
The test organisms, C. volutator and H. diversicolor, were collected from the Eastern Scheldt
located in the south-western part of the Netherlands, which is used as a non-contaminated
control site for conducting whole-sediment bioassays (Kater et al., 2006; van den Heuvel-
Greve et al., 2007). The field collection of C. volutator followed standard guidelines used
around the world (Roddie & Thain, 2002). C. volutator were collected at low tide, when the
shore was exposed, by carefully removing the upper 5 cm layer of sediments with a small
stainless steel shovel into 10 L plastic buckets. The sediments were subsequently sieved over
a 0.5 mm mesh with seawater from the same area (salinity of 30-31 ‰) into a separate 10 L
plastic bucket while the C. volutator retained on the sieve were carefully transferred into
another 10 L plastic bucket containing seawater. The sieved sediment (about 2 kg) was mixed
thoroughly and kept as control sediment for the C. volutator bioassay.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
157
H. diversicolor was carefully collected by hand along the banks of the Eastern Scheldt
estuary, together with some of their associated sediments, and placed in a 10 L plastic bucket.
The sediment was then covered by a layer of about 20 cm estuarine water. About 3 kg of
sediment was also collected from the same area and sieved over a 0.5 mm mesh with some
estuarine water from the same area into a 10 L plastic bucket to serve as control sediment for
the H. diversicolor bioassay.
During sampling, care was taken to ensure that the C. volutator and H. diversicolor were not
damaged. The collected samples were transported to the SPHERE laboratory, where the C.
volutator and H. diversicolor aquaria were kept under continuous aeration at 15 °C in a
climate-controlled room for 7 d for organisms to acclimatise prior to the whole-sediment
bioassays. The water salinity in the aquaria was monitored with a conductivity meter (HACH,
USA) during the acclimatisation period and kept at 30 ‰ by the addition of deionised water.
6.2.4. Laboratory bioassay experiments
The standard acute 10-day C. volutator whole-sediment bioassay as described by Roddie &
Thain (2002) and Schipper et al. (2006) was adopted. The C. volutator used were of similar
sizes (typically 4-5 mm long). The bioassays were conducted on sediments from the Tema
Harbour and the reference site (control) in acid-washed 1.5 L wide-mouth glass bottles. Each
set-up contained 200 mL homogenised sediment sample (about 3 cm thick), 600 mL well-
aerated artificial seawater (about 12 cm depth of overlying seawater) of 30 ‰ salinity and 20
active individuals of C. volutator. Five (5) replicates were prepared for the control and the
Tema Harbour sediment bioassays, except for the MH1 (n = 4) and OFH (n = 3) bioassays,
due to loss of sample during transport.
The standard chronic 28-day H. diversicolor whole-sediment bioassay as described by
Hannewijk et al. (2004) was adopted. H. diversicolor of similar mass (typically 0.2-0.3 g fresh
weight) were used. The bioassays were conducted on sediments from the Tema Harbour and
the reference site (control) in acid-washed 0.5 L wide-mouth glass bottles. Each set-up
contained 100 mL homogenised sediment samples (about 3 cm thick), 120 mL artificially
prepared seawater (about 6 cm depth of overlying seawater) and one active H. diversicolor.
Fifteen (15) replicates were prepared for the control bioassay, while the number of bioassay
replicates prepared per type of Tema Harbour sediment varied from 10 to 13, due to limited
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
158
quantity of sediment sample. No CB sediment sample was available to conduct the H.
diversicolor bioassay.
Prior to the introduction of C. volutator and H. diversicolor, the overlying seawater in each
bottle was aerated continuously for 48 h to ensure adequate supply of oxygen, while avoiding
sediment resuspension. Moreover, care was taken to ensure that the organisms were not
damaged while being introduced into the bottles. All bioassays were conducted at a
temperature of 15 (± 1) oC and under a light regime of 16 h light and 8 h darkness. Periodic
measurements of pH, salinity and dissolved oxygen (DO) levels of the overlying seawater
were conducted from the start till the end of the exposure period using a pH meter,
conductivity meter and DO meter (HACH, USA), respectively, and adjustments to the initial
salinity were made when necessary. H. diversicolor were fed 3 times per week with 30 mg of
ground fish food (TetraMin® XL Flakes) (Hannewijk et al., 2004), while their overlying
seawater was renewed weekly to minimise the potential build-up of ammonia and hydrogen
sulphide (Ferretti et al., 2000). At the end of their exposure periods, C. volutator were gently
sieved over a 0.5 mm mesh, while H. diversicolor were gently removed with a pair of forceps.
The organisms were then rinsed with artificial seawater to remove adhering particles and the
numbers of living organisms were counted to determine mortalities.
6.2.5. Analyses of metal, sediment grain size and TOC contents
Upon completion of the bioassays, the organisms and sediment samples were freeze-dried
prior to analyses of their metal contents. Metal analysis in C. volutator and H. diversicolor
was based on whole-body tissues. H. diversicolor were analysed individually for metals. In
the case of C. volutator, five composite samples were obtained from each replicate by pooling
four individuals together and subsequently analysing their metal content. The freeze-dried C.
volutator and H. diversicolor samples, together with 0.2 g portions of a mussel-based standard
reference material (SRM 2976) from the National Institute of Standards and Technology
(NIST, Luxembourg, Belgium) and procedural blanks were subjected to microwave-assisted
digestion using 2 mL HNO3 (for H. diversicolor) or 0.5 mL HNO3 (for C. volutator).
About 0.2 g portions of freeze-dried homogenised sediment samples, a sediment certified
reference material (BCR-701) and procedural blanks were analysed for total metal
concentrations and metal fractionation by adopting the harmonised Community Bureau of
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
159
Reference (BCR) 3-step sequential extraction and aqua regia extraction techniques,
respectively, following Pueyo et al. (2001). The metal concentrations were measured using
ICP-MS (Varian, Australia). The dry sediments were also analysed for their grain-size
distribution by the Malvern laser diffraction method (Blott et al., 2004), while total organic
carbon (TOC) was analysed by the Walkey-Black wet oxidation method following Botwe et
al. (2017). The mean metal recoveries in the standard BCR-701 samples ranged between 77
and 116 % with relative standard deviation (RSD) of 1.3-11.8 %, while the mean metal
recoveries in the NIST SRM 2976 varied between 86 and 102% with RSD of 0.6-5.3 %,
depending on the metal measured. Metal concentrations in the biota and sediment samples
were corrected for recovery, using their respective mean recoveries in the certified reference
materials.
6.2.6. Data analysis
One-way analysis of variance (ANOVA) and Holm-Sidak multiple comparison tests or
Kruskal-Wallis one-way ANOVA on ranks (where normality test failed) were used to test for
significant differences in C. volutator and H. diversicolor mortalities as well as metal
concentrations in sediments across sites by using the statistical software SigmaPlot (version
11.0). Using the same software, normality and equal variance tests were performed with the
Shapiro-Wilk and Levene's mean tests, respectively. Two-tailed Pearson correlations (using
SPSS, version 16.0) among metal bioaccumulation factor, metal concentration in sediment,
mortality and TOC content in sediment were determined separately for C. volutator (n = 6)
and H. diversicolor (n = 5).
Regression plots were made to determine linear associations between measured parameters of
interest using MS Excel 2007. To characterise the potential ecological impact of metal
contamination in Tema Harbour sediments, biota-sediment accumulation factors (BSAFs)
were estimated by dividing the metal concentrations in whole-body tissues of C. volutator and
H. diversicolor by the corresponding concentrations in the sediment (Aydin-Onen et al.,
2015). A BSAF >1.0 is indicative that metal bioaccumulation has occurred, and the greater the
BSAF, the greater the bioaccumulation efficiency (Aydin-Onen et al., 2015). When necessary,
raw metal concentrations were normalised to the <63 µm fraction of sediments as follows
(Horowitz, 1985):
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
160
[ ]
( ) [ ] ( )
where [Metal]n is the normalised metal concentration and [metal]r is the raw metal
concentration.
6.3. Results
6.3.1. C. volutator and H. diversicolor mortalities in the whole-sediment bioassays
The mean C. volutator mortalities in the MH1, MH2, OFH, IFH, CB and control bioassays
were 29, 38, 77, 99, 98 and 7 %, respectively (Fig. 6.2). One-way ANOVA (p < 0.001; n = 6)
followed by the Holm-Sidak multiple comparison test (p < 0.05; n = 6) showed that the
mortalities of C. volutator in the Tema Harbour sediment bioassays were significantly higher
than those of the control bioassays with the following mortality trend across the Tema
Harbour sediments: MH1 < MH2 < OFH < IFH ≈ CB. The H. diversicolor mortalities in the
MH1, MH2, OFH and IFH bioassays were 46, 15, 10 and 92 %, respectively, while the
control mortality was 7 % (Fig. 6.3). As in the case of C. volutator, the highest H. diversicolor
mortality was associated with the IFH sediments. However, Fig. 6.3 shows that the trend in H.
diversicolor mortality across the Tema Harbour sediments was OFH < MH2 < MH1 < IFH,
which contrasted with the trend in C. volutator mortality (Fig. 6.2): the MH2 and OFH
sediments caused low H. diversicolor mortalities (10-15 %) but high C. volutator mortalities
(38-77 %).
6.3.2. Physicochemical conditions of water and sediments from the Tema Harbour
and control bioassays
The physicochemical conditions of water and sediments from the Tema Harbour and control
bioassays are summarised in Table 6.1. The salinity, pH and dissolved oxygen (DO) levels of
the overlying water during the bioassay experiments varied between 28-34 ‰, 7.7-8.5 and
7.4-8.7 mgL-1
, respectively. There were marked differences in the grain size distributions of
the Tema Harbour and control sediments: whereas sand (63-500 µm fraction) dominated the
control sediment (62-90 %), a predominance (63-88 %) of silt (4-63 µm fraction) was present
in the Tema Harbour sediments. However, the control sediments had a relatively higher TOC
content (5.2-5.9 %) than the Tema Harbour sediments (2.9-4.2 %). Neither sediment grain
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
161
n = 13
n = 13 n = 10
n = 12
n = 15
0
20
40
60
80
100
MH1 MH2 OFH IFH Control
H. d
ivers
ico
lor
mo
rtalit
y (
%)
Sediment sample area
Fig. 6.2 Mean C. volutator mortalities in 10-day bioassay tests with whole-sediments
from different areas within Tema Harbour, Ghana (MH1, MH2, OFH, IFH and CB)
and the Eastern Scheldt, The Netherlands (control), indicating the number of
replicates (n) and the standard error of the mean (error bars).
Fig. 6.3 H. diversicolor mortalities in 28-day bioassay tests with whole-sediments
from different areas within Tema Harbour, Ghana (MH1, MH2, OFH and IFH) and the
Eastern Scheldt estuary, The Netherlands (control), indicating the number of
replicates (n).
n = 4 n = 5
n = 3
n = 5 n = 5
n = 5
0
20
40
60
80
100
MH1 MH2 OFH IFH CB Control
C.
vo
luta
tor
mo
rta
lity (
%)
Sediment sample area
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
162
size nor TOC content correlated significantly with both C. volutator mortality and H.
diversicolor mortality.
Table 6.1 Physicochemical conditions of water and sediments in bioassays of bottom
sediments from Tema Harbour, Ghana and Eastern Scheldt, The Netherlands
(reference controls)
a sediments from Tema Harbour;
b reference sediment from C. volutator site;
c reference
sediment from H. diversicolor site
6.3.3. Total metal concentrations and metal fractionation in the analysed sediments
The mean total metal concentrations in the Tema Harbour sediments (mg.kg-1
dw) ranged
from 0.07 - 1.16 for Cd, 24.9-102 for Pb, 50.1-80.3 for Cr, 17.4-27.7 for Ni, 33.4-210 for Cu,
98-730 for Zn, and 7.9-14.2 for As (Table 6.2). One-way ANOVA (p < 0.001) followed by
the Holm-Sidak multiple comparison test revealed significant differences (p < 0.05; n = 6) in
the total concentrations of Pb and Zn (i.e., CB > IFH > OFH > MH1 > MH2), Cr (i.e., IFH >
OFH > MH1 > CB > MH2) and Ni (i.e., OFH > IFH > MH1 > CB > MH2) across the Tema
Harbour sediments. Kruskal-Wallis one-way ANOVA on ranks also revealed significant
differences in the sediment concentrations of Cd (p < 0.003), Cu (p < 0.004) and As (p <
0.004) across the Tema Harbour bottom. The CB sediments had the highest Cd concentration,
whereas the IFH sediments had the highest Cu and As concentrations. The mean
concentrations for each metal for the Tema Harbour sediments were greater than the means
for the Eastern Scheldt (control) sediments, except for Cd. A statistically significant
correlation was observed between sediment Cd concentration and C. volutator mortality (r =
Physicochemical conditions of
water from bioassays
Sediment grain size
distribution (%)
Sediment
sample
Salinity
(‰) pH
DO
(mg/L)
<4
µm
4-63
µm
63-500
µm
TOC
(%)
aMH1 30-32 8.0-8.4 7.9-8.4 10 79 11 3.2
aMH2 30-32 7.8-8.3 8.2-8.5 8 63 29 2.9
aOFH 30-33 7.7-8.4 7.9-8.1 12 85 3 3.6
aIFH 30-32 7.8-8.5 7.4-7.8 12 88 0 4.2
aCB 30-32 8.1-8.5 8.0-8.5 10 86 4 3.6
bRC 30-34 8.2-8.5 8.1-8.5 2 8 90 5.2
cRH 28-31 8.0-8.4 7.9-8.7 4 34 62 5.9
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
163
0.84, p < 0.05; n = 6), with a high coefficient of determination (r2 = 0.85) (Fig. 6.4a). In the
case of H. diversicolor, a statistically significant correlation was observed between mortality
and sediment Cu concentration (r = 0.94, p < 0.05; n = 5), with a high coefficient of
determination (r2 = 0.89) (Fig. 6.4b).
Table 6.2 Mean (n = 3) concentrations of selected metals in sediments from Tema
Harbour, Ghana and Eastern Scheldt, The Netherlands reference sites,
and sediment quality guidelines (mg.kg-1 dw).
a same definition as in Table 6.1;
b Sediment quality guidelines (DelValls et al., 2004); ERL
represents a metal concentration associated with rare occurrence of harmful biological effects,
the ERL-ERM interval represents a range of metal concentrations likely to cause harmful
biological effects occasionally, while the ERM represents a metal concentration likely to
cause harmful biological effects frequently (Long et al., 1995).
The fractionation of metals among exchangeable, reducible, oxidisable, and residual phases in
the Tema Harbour sediments is shown in Table 6.3. Zn was present in appreciable amounts in
all four fractions. The sediments contained considerable fractions of exchangeable metals only
for Cd (15.7-46.8 %) and Zn (8.6-32.6 %). Cd (96.1-99.7 %), Pb (86.3-95 %), Cu (54.1-90.5
%) and Zn (72.2-96.5 %) were mainly present in the labile (i.e., the exchangeable, reducible
and oxidisable) fractions rather than in the residual fraction. In contrast, Cr, Ni and As were
predominantly present in the residual fraction, except for the IFH and CB sediments.
Sediment
sample Cd Pb Cr Ni Cu Zn As
aMH1 0.12 ± 0.00 39.7 ± 1.4 63.6 ± 1.6 24.2 ± 0.5 100 ± 0.4 190 ± 7 7.9 ± 0.2
aMH2 0.07 ± 0.00 24.9 ± 0.9 50.1 ± 0.8 17.4 ± 0.5 33.4 ± 0.5 98.0 ± 1.4 8.5 ± 0.2
aOFH 0.19 ± 0.00 50.6 ± 0.6 78.0 ± 0.2 27.7 ± 1.2 78.0 ± 2.1 244 ± 3 13.0 ± 0.2
aIFH 0.43 ± 0.03 84.3 ± 0.9 80.3 ± 0.3 26.0 ± 1.0 210 ± 7 415 ± 4 14.2 ± 0.5
aCB 1.16 ± 0.05 102 ± 2 61.2 ± 0.9 23.3 ± 0.5 195 ± 1 730 ± 5 12.6 ± 0.3
aRC 0.04 ± 0.01 4.6 ± 0.2 15.1 ± 0.5 3.0 ± 0.1 3.0 ± 0.2 14.7 ± 0.4 3.6 ± 0.1
aRH 0.21 ± 0.02 11.1 ± 0.7 20.4 ± 0.8 6.5 ± 0.6 6.5 ± 0.6 47.8 ± 4.4 5.7 ± 0.5
bERL 1.2 46.7 81 20.9 34 150 8.2
bERM 9.6 218 370 51.6 270 410 70
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
164
y = 28.315ln(x) + 107.64 R² = 0.8483
0
20
40
60
80
100
0.0 0.5 1.0 1.5C. vo
luta
tor
mo
rtalit
y (
%)
Cd concentration in sediment (mg.kg-1 dw)
a
y = 0.4313x - 2.9078 R² = 0.893
0
20
40
60
80
100
0 100 200 300
H. d
ivers
ico
lor
mo
rtalit
y
(%)
Cu concentration in sediment (mg.kg-1 d.w)
b
Fig. 6.4 Scatter plots of (a) C. volutator mortality versus Cd concentration in whole
sediment (correlation coefficient, r = 0.84, p < 0.05; n = 6) and (b) H. diversicolor
mortality versus Cu concentration in whole sediment (correlation coefficient, r = 0.94,
p < 0.05; n = 5).
6.3.4. Metal bioaccumulation in C. volutator and H. diversicolor
Table 6.4 presents the mean concentrations of metals in whole-body tissues of C. volutator
and H. diversicolor as well as their corresponding biota-sediment accumulation factors
(BSAFs). The mean tissue Cd, Pb, Cr, Ni, Cu, Zn and As concentrations of C. volutator
exposed to the Tema Harbour sediments were, respectively, 1-5, 4-17, 1-5, 2-5, 2-12, 2-7 and
1-5 times those of the controls. Similarly, the mean tissue Cd, Pb, Cr, Ni, Cu, Zn and As
concentrations of H. diversicolor exposed to the Tema Harbour sediments were, respectively,
0-13, 4-10, 1-6, 1-3, 3-5, 3-4 and 2-4 times those of the controls. Generally, the metal BSAFs
for H. diversicolor were markedly higher than those of C. volutator (except in some cases of
Cd). In the tissues of C. volutator, Zn and Cu were found in the highest concentrations relative
to the other metals, while Zn was found in the highest concentrations in H. diversicolor.
However, for both C. volutator and H. diversicolor, the BSAFs of As were relatively higher
than those of the other metals investigated. For all the metals investigated, no statistically
significant correlations (p > 0.05) were observed between the sediment and tissue
concentrations in C. volutator and H. diversicolor.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
165
Table 6.3 Metal fractionation over the different phases in sediments from Tema
Harbour, Ghana
Fraction of metals (%) associated with the different sediment phases
Sediment
sample
Sediment
phase Cd Pb Cr Ni Cu Zn As
MH1 Exchangeable 46.8 2.8 0.3 4.0 1.5 20.8 2.8
Reducible 30.7 79.6 18.7 8.6 42.8 48.4 20.6
Oxidisable 19.6 6.3 21.3 16.1 30.0 11.4 9.9
Residual 2.9 11.2 59.7 71.3 25.7 19.4 66.6
Labile 97.1 88.8 40.3 28.7 74.3 80.6 33.4
MH2 Exchangeable 23.3 1.5 0.2 0.0 0.4 8.6 5.4
Reducible 39.3 74.2 15.7 8.7 29.9 49.2 18.7
Oxidisable 33.5 10.6 27.5 17.6 23.8 14.4 8.9
Residual 3.9 13.7 56.6 73.7 45.9 27.8 66.9
Labile 96.1 86.3 43.4 26.3 54.1 72.2 33.1
OFH Exchangeable 36.0 1.2 0.2 4.3 1.0 21.7 1.6
Reducible 46.8 78.8 20.7 12.3 41.4 53.4 25.5
Oxidisable 14.7 7.5 24.4 18.9 32.7 10.8 13.8
Residual 2.6 12.5 54.7 64.6 24.9 14.1 59.1
Labile 97.4 87.5 45.3 35.4 75.1 85.9 40.9
IFH Exchangeable 32.0 0.8 0.2 3.9 0.9 27.6 1.5
Reducible 53.5 74.0 19.3 10.1 39.5 50.4 29.7
Oxidisable 13.9 17.0 37.7 28.1 48.5 15.2 24.8
Residual 0.6 8.2 42.9 57.8 11.2 6.8 43.9
Labile 99.4 91.8 57.1 42.2 88.8 93.2 56.1
CB Exchangeable 15.7 0.2 0.4 7.1 0.4 32.6 8.0
Reducible 70.5 76.2 25.5 11.2 41.0 51.7 39.2
Oxidisable 13.4 18.6 28.3 26.5 49.0 12.2 24.9
Residual 0.3 5.0 45.8 55.2 9.5 3.5 28.0
Labile 99.7 95.0 54.2 44.8 90.5 96.5 72.0
Risk assessment code (RAC) based on the percentage of sediment-associated metal in the
exchangeable phase is as follows (Jain, 2004): no risk (<1 %), low risk (1-10 %), medium risk
(11-30 %), high risk (31-50) and very high risk (>50 %). Labile fraction = sum of the
fractions in the exchangeable, reducible and oxidisable phases.
Table 6.4 Metal concentrations (mean ± SE, mg.kg-1 dw) in whole-body tissues of C. volutator and H. diversicolor exposed to
sediments from Tema Harbour, Ghana and estimated metal biota-sediment accumulation factors (BSAFs)
a sediments from Tema Harbour;
b reference sediment from C. volutator site;
c reference sediment from H. diversicolor site; ND = not detected
Mean metal concentrations (BSAFs)
Sediment
sample Cd Pb Cr Ni Cu Zn As
C. volutator aMH1 0.08 ± 0.01 (0.7) 2.1 ± 0.02 (0.05) 2.0 ± 0.3 (0.03) 1.5 ± 0.1 (0.06) 51 ± 3 (0.5) 52 ± 5 (0.3) 19 ± 1 (2.4)
aMH2 0.13 ± 0.01 (1.9) 4.7 ± 1.7 (0.2) 3.0 ± 0.5 (0.06) 1.6 ± 0.1 (0.1) 60 ± 3 (1.8) 57 ± 3 (0.6) 22 ± 2 (2.6)
aOFH 0.22 ± 0.01 (1.2) 9.8 ± 1.2 (0.2) 6.7 ± 0.9 (0.1) 3.7 ± 0.4 (0.1) 240 130 (3.1) 160 ± 30 (0.7) 45 ± 1 (3.5)
aIFH 0.05 ± 0.02 (0.12) 6.4 ± 1.2 (0.1) 3.8 ± 0.1 (0.05) 1.8 ± 0.1 (0.07) 50 ± 14 (0.2) 55 ± 9 (0.1) 12 ± 6 (0.9)
aCB 0.11 ± 0.03 (0.1) 8.6 ± 1.6 (0.1) 4.0 ± 0.7 (0.07) 2.1 ± 0.3 (0.1) 66 ± 11 (0.3) 80 ± 12 (0.1) 18 ± 2 (1.4)
bRC 0.05 ± 0.01 (1.3) 0.6 ± 0.1 (0.1) 1.4 ± 0.2 (0.1) 0.7 ± 0.1 (0.2) 20 ± 1 (6.7) 23 ± 2 (1.6) 10 ± 1 (2.8)
H. diversicolor aMH1 0.61 ± 0.50 (5) 110 ± 30 (3) 110 ± 48 (2) 100 ± 30 (4) 620 ± 130 (6) 7900 ± 1000 (42) 910 ± 70 (115)
aMH2 0.04 ± 0.03 (0.6) 180 ± 60 (75) 110 ± 60 (2) 80 ± 28 (4.6) 960 ± 240 (29) 9100 ± 1400 (93) 1140 ± 160 (134)
aOFH 2.6 ± 1.8 (14) 240 ± 130 (5) 90 ± 70 (1.2) 110 ± 50 (4) 1040 ± 270 (13) 10900 ± 1200 (45) 1440 ± 200 (110)
aIFH ND 260 ± 150 (3) 24 ± 12 (0.3) 47 ± 16 (2) 1090 ± 330 (5) 10400 ± 2100 (25) 730 ± 230 (51)
cRH 0.20 ± 0.12 (1) 24 ± 6 (2) 18 ± 7 (1) 37 ± 8 (6) 200 ± 20 (31) 2800 ± 400 (58) 390 ± 50 (68)
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
167
6.4. Discussion
6.4.1. Hazard potential of Tema Harbour sediments
This study showed that the mean C. volutator mortalities in the Tema Harbour sediment
bioassays exceeded the mean control mortality by >20% (Fig. 6.2), indicating that all the
Tema Harbour sediments were toxic or hazardous to C. volutator (EPA, 1998). According to
the International Council for the Exploration of the Sea based on C. volutator whole-sediment
bioassays (ICES, 2008), sediment toxicity is classified as "elevated" or "high concern" if the
C. volutator mortality exceeds that of the control by >30% and >60%, respectively. Thus, the
MH2 sediments had elevated toxicity, whereas the toxicities of the OFH, IFH and CB
sediments were of high concern. During the exposure period, no burrowing activity was
observed in the IFH and CB sediments as most of the C. volutator avoided these sediments
and kept swimming in the water column. This behaviour, which was not observed in the
control and the remaining sediments, is an indication that C. volutator avoided the highly
toxic sediments (Bat & Raffaelli, 1998; Bat, 2005).
Higher mortalities of H. diversicolor were observed in the MH1 (46%) and IFH (92%)
sediment bioassays than in the control (7%), indicating that the MH1 and IFH sediments were
also hazardous to H. diversicolor. However, the mortalities of H. diversicolor in the MH2
(15%) and the OFH (10%) were within the acceptable mortality of 10-15% (Thain & Bifield,
2002; ICES, 2008). As in the case of C. volutator, no burrowing activity of H. diversicolor
was observed in the IFH sediments, possibly due to the high toxicity of the sediment (Bat &
Raffaelli, 1998).
C. volutator and H. diversicolor exhibited strikingly different vulnerabilities towards the
toxicities of the MH2 and OFH sediments, which underscores the importance of using a
battery of species in whole-sediment toxicity bioassays (Bat & Raffaelli, 1998; DelValls et al.,
2004; Eisentraeger et al., 2004; Annicchiarico et al., 2007; Schipper et al., 2010). Figs. 6.2
and 6.3 show that the MH2 and OFH sediments caused higher mortalities of C. volutator (38
and 77 %, respectively) than H. diversicolor (15 and 10 %, respectively). This observation
supports previous findings that amphipods such as C. volutator are more sensitive to sediment
toxicity than polychaetes such as H. diversicolor (Long et al., 2006). Moreover, sediments are
often contaminated by a range of toxicants (Burton Jr, 2002; Forrester et al., 2003; Long et al.,
2006), which may potentially impose different toxic responses on C. volutator and H.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
168
diversicolor. For example, Bat & Raffaelli (1998) have shown that C. volutator and the
marine polychaete Arenicola sp. have different sensitivities to Cu, Cd and Zn. They observed
that lethal concentrations (LC50) of Cu, Cd and Zn differed for C. volutator (37, 14 and 32
mg.kg-1
dw, respectively) and Arenicola sp. (20, 35 and 50 mg.kg-1
dw, respectively). This
indicates that C. volutator is more sensitive to Cd and Zn, but less sensitive to Cu, than
Arenicola sp..
The lower sensitivity of C. volutator to Cu compared to H. diversicolor has also been
observed by Mayor et al. (2008), who reported LC50 values of 193 and 75 mg.kg-1
ww,
respectively. The levels of Cd in the Tema Harbour sediments were much lower than the LC50
value of Cd for C. volutator,reported by Mayor et al. (2008). The levels of Cu (except for the
MH2 sediments) and Zn in the Tema Harbour sediments exceeded their corresponding LC50
values reported for C. volutator (Bat & Raffaelli, 1998). This suggests that Cu and Zn may
play a significant role in the toxicity of the Tema Harbour sediments. Bat & Raffaelli (1998)
also observed that the mortality of C. volutator increased with increasing sediment Cu, Cd and
Zn concentrations. In this study, statistically significant correlations were observed between
C. volutator mortality and sediment Cd concentration and between H. diversicolor mortality
and sediment Cu concentration. Scatter plots show that the former correlation is logarithmic
with a high regression coefficient (R2) of 0.85, whereas the latter correlation is linear with a
high R2 of 0.88 (Figs. 6.4a & 6b). The variation in sediment Cd and Cu concentrations could
explain the variation in C. volutator and H. diversicolor mortalities, respectively. In the Main
Harbour, for example, the Cu level in the MH1 sediment was higher than that of the MH2
sediment, the former resulting in a correspondingly higher H.diversicolor mortality. Although
the level of Cu in the MH2 sediment was lower than that of the OFH sediment, the latter
resulted in a lower H. diversicolor mortality. Clearly, other factors apart from the measured
metals may play a role in the sediment toxicity to H. diversicolor. A potential source of the
Cu contamination in the harbour sediments is the use of Cu-based antifouling paints on
marine crafts to mitigate biofouling (Mukherjee et al., 2009).
Despite their markedly different vulnerabilities to the toxicities of the MH2 and OFH
sediments, both C. volutator and H. diversicolor clearly distinguished the IFH sediments as
being highly toxic or hazardous. The high toxicity of the CB sediments indicated by the
associated high C. volutator mortality (98 %) could not be confirmed by using H.
diversicolor, due to limited sediment quantity. The high toxicities of sediments from the IFH,
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
169
OFH and the CB are a clear indication that these areas are the most polluted within the Tema
Harbour, which may be due to intense anthropogenic activities. The IFH and the OFH sustain
a productive fishing industry through the provision of handling facilities for semi-industrial
and industrial fishing vessels as well as a storage facility for petroleum products, while the CB
is a dedicated artisanal canoe landing site. Daily, an average of 125 vessels operate from the
IFH and the OFH, while the CB is normally overcrowded.
Fishing-related activities such as refuelling, painting of vessels and canoes, discharges of
industrial wastewater and dumping of solid and liquid wastes by the fisherfolk are potential
sources of chemical contamination in the Tema Harbour. Petroleum contamination was visible
in the sediments from the IFH and the CB, possibly as a result of oil spills during refuelling of
fishing vessels and fuel leakage in these sampling areas. Since their construction in 1962, the
IFH and the OFH have not been dredged and there is a potential for pollutant accumulation in
these areas over the years. The CB was dredged in May 2013 and hence, the high
contamination of its sediments is an indication of high anthropogenic influences in this area.
Although the Main Harbour is also subject to pollution from industrial wastewater discharges,
ship traffic, oil spills during bunkering as well as dry dock activities such as scraping and
painting of vessels (Mestres et al., 2010), recent maintenance dredging in March-April 2014
might have removed polluted sediments resulting in lower toxicities.
The control mortalities of both C. volutator and H. diversicolor in the whole-sediment toxicity
bioassays (7%) were acceptably low, compared to the maximum acceptable mortality of 10-
15% (Roddie & Thain, 2002; Casado-Martinez et al., 2007; Thain & Bifield, 2002; ICES,
2008). Moreover, the salinity, pH, dissolved oxygen and temperature of the overlying water
during the bioassay experiments were all within acceptable ranges (Roddie & Thain, 2002;
Thain & Bifield, 2002; Hannewijk et al., 2004; Schipper et al., 2006).
6.4.2. Potential ecological risks of metal contamination in Tema Harbour sediments
The potential ecological risks posed by metal (Cd, Pb, Cr, Ni, Cu, Zn and As) contamination
in the Tema Harbour sediments were characterised by applying a pair of sediment quality
guidelines, namely the effects-range low (ERL) and effects-range median (ERM). The ERL
represents a pollutant concentration with a high probability to rarely cause harmful biological
effects, the ERL-ERM interval represents a range of pollutant concentrations with a high
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
170
probability to cause harmful biological effects occasionally, while the ERM represents a
pollutant concentration with a high probability to cause harmful biological effects frequently
(Long et al., 1995; Burton Jr, 2002; Long et al., 2006; DelValls et al., 2004; Birch & Hutson,
2009). Based on the ERL and ERM values (Table 6.2), two risk quotients, the ERL quotient
(ERLQ) and the ERM quotient (ERMQ), were derived for each measured metal according to
Eq. (2) and (3), respectively:
( )
( ) ( )
( )
( ) ( )
When the ERLQ exceeded 1.0, the corresponding ERMQ was derived instead in order to
define three levels of potential risk associated with the measured metal concentration as
follows: low risk for ERLQ ≤ 1.0, moderate risk for ERMQ < 1.0, and high risk for ERMQ ≥
1.0.
The results showed that for all the Tema Harbour sediments analysed, at least one of the
investigated metals may pose a moderate or high risk of harmful biological effects (Table
6.5). In particular, the levels of Zn in sediments from the IFH and the CB pose high potential
ecotoxicological risks and are, therefore, of potential concern. This further supports the
suggestion that Zn may play a significant role in the toxicity of the Tema Harbour sediments,
and identifies the IFH and the CB as priority areas for management and remediation attention
in the Tema Harbour. The levels of Ni and Cu (except for the MH2 sediment, where they may
pose low potential risks), as well as As (except for the MH1 sediment, where the potential risk
is low) pose moderate potential ecotoxicological risks. The levels of Cd and Cr present low
potential ecotoxicological risks. The levels of Pb in sediments from the IFH, OFH and the CB
were associated with moderate potential ecotoxicological risks, while those of the MH1 and
the MH2 sediments were associated with low potential ecotoxicological risks.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
171
Table 6.5 Derived risk quotients to assess risks posed by metal levels in sediments
from Tema Harbour, Ghana (see Section 6.4.2 for derivation)
Risk quotients
Sediment
sample Cd Pb Cr Ni Cu Zn As
MH1 0.10 0.85 0.79 0.47 0.37 0.47 0.97
MH2 0.06 0.53 0.62 0.83 0.98 0.65 0.12
OFH 0.15 0.23 0.96 0.54 0.29 0.60 0.19
IFH 0.35 0.39 0.99 0.50 0.73 1.01* 0.20
CB 0.97 0.47 0.76 0.45 0.72 1.79 0.18
Unbold = effects-range low quotients (ERLQs): Bold = effects-range median quotients
(ERMQs).
Metals fractionate over different phases in sediment: the exchangeable (carbonate-bound),
reducible (iron/manganese oxide-bound), oxidisable (organic/sulphide-bound) and
residual/refractory (silicate/mineral-bound) phases. Metals in the exchangeable phase are the
most weakly bound and represent the potentially bioavailable fraction (Jain 2004; Igari et al.,
2012; Iqbal et al., 2013). Based on the percentage of metal in the exchangeable phase, also
known as the risk assessment code (RAC), the potential risks were characterised as follows
(Jain, 2004): no risk (<1 %), low risk (1-10 %), medium risk (11-30 %), high risk (31-50) and
very high risk (>50 %). Thus, the measured metal concentrations in the Tema Harbour
sediments pose the following potential ecological risks: medium-high risk for Cd; low to high
risk for Zn; low risk for As; no to low risk for Pb, Ni and Cu; and no risk for Cr (Table 6.3).
The relatively higher exchangeable fractions of Cd (15.7-46.8 %) and Zn (8.6-32.6 %) (Table
6.3) indicate that Cd and Zn had the highest potential of entering the food chain (Jain, 2004;
Igari et al., 2012; Iqbal et al., 2013). The predominance of Cd, Pb, Cu and Zn in the labile
phase, rather than the residual phase, suggests that these metals are derived predominantly
from anthropogenic sources (Jain, 2004). Ni was predominantly in the residual phase,
suggesting that it is mainly of natural origin. With regards to Cr and As, a predominance of
the labile phase was observed in sediments from the IFH and the CB, suggesting greater
anthropogenic influences in these areas of the Tema Harbour.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
172
6.4.3. Potential ecological impact of sediment-associated metal in Tema Harbour
Benthic organisms can accumulate sediment-associated contaminants e.g. through direct
ingestion of sediments (Burton Jr, 2002) and impact other organisms and humans via food
chain transfer of the accumulated metals (Marsden & Rainbow, 2004). Table 6.4 shows that in
most cases, the metal BSAFs for H. diversicolor exceeded 1.0, indicating a significant
bioaccumulation of the investigated metals by H. diversicolor (Aydin-Onen et al., 2015). The
metal BSAFs for H. diversicolor were higher than those for C. volutator, which may be
attributed to the longer exposure periods for H. diversicolor (28 d) than C. volutator (10 d)
and potential variability in metal bioaccumulation by different species (Marsden & Rainbow,
2004) due to e.g. potential differences in the ability to store or eliminate the metals (Adams et
al., 2011). For both C. volutator and H. diversicolor, the BSAFs of As were higher than those
of the other investigated metals, suggesting that among the investigated metals, As was either
most efficiently taken up or least regulated by both C. volutator and H. diversicolor.
In most cases, C. volutator and H. diversicolor exposed to the Tema Harbour sediments had
higher tissue concentrations of metals than the controls. Thus, the Tema Harbour sediments
can be a significant source of metal bioaccumulation for benthic organisms with potential
adverse impact on the aquatic food chain. Although the degree of contamination in harbours
may be evident from the contamination patterns in the sediments and from biomarkers (de
Boer et al., 2001; Schipper et al., 2009), this is not always evident (Schipper et al., 2009).
Contrary to findings of other studies (Bat & Raffaelli, 1998), no statistically significant
correlations were found between metal bioaccumulation (or metal bioavailability) and the
corresponding metal concentrations in sediment or TOC content in this study. Moreover, no
statistically significant correlations were found between metal bioaccumulation and mortality
for both C. volutator and H. diversicolor. This lack of correlation is possibly due to the
potential of the organisms to regulate metal uptake (Adams et al., 2011). Burrowing behaviour
appeared to influence metal bioaccumulation as the non-burrowing organisms (those exposed
to the IFH and CB bioassays) tend to have lower metal bioaccumulation factors. This is
expected as burrowing results in increased exposure of organisms to contaminants in
sediments (Bat, 2005).
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
173
6.4.4. Dredged material management implications for Tema Harbour
The practice of harbour dredging with subsequent disposal at sea poses a potential hazard to
biota in the receiving site as dredged materials are often found to contain hazardous
concentrations of chemical contaminants (Marsden & Rainbow, 2004; Schipper et al., 2010).
To guide the management and disposal of dredged materials, countries such as the
Netherlands and Spain have developed sediment quality guidelines or action levels, which
represent potentially hazardous concentrations of chemical pollutants (DelValls et al., 2004;
Casado-Martinez et al., 2006; Kelderman, 2012; Schipper et al., 2013).
Currently, no regulatory standards have been established for dredged materials in Ghana,
despite routine maintenance dredging with subsequent disposal or storage at sea. Thus, in
addition to the bioassay tests, the Spanish action levels (action levels 1 and 2) for dredged
materials (DelValls et al., 2004; Casado-Martinez et al., 2006) were compared to the data for
this study. These Spanish action levels are based on the probability of their associated
chemical concentrations to cause adverse effects in marine biota (Casado-Martinez et al.,
2006) and are presented in Table 6.6. Based on these action levels, dredged materials may be
classified into three categories, which can then influence decisions about their management
and disposal. Category I dredged materials have pollutant concentrations below action level 1
(AL1) and their disposal at sea is allowed, whereas category II dredged materials have
pollutant concentrations between AL1 and action level 2 (AL2) and thus, would require
further assessments to determine their suitability for disposal at sea. Category III dredged
materials have pollutant concentrations above AL2 and, therefore, would require isolation or
disposal in a confined area (DelValls et al., 2004). Since the AL1 and AL2 are based on the
<63 µm fraction of sediments (DelValls et al., 2004), it was necessary to normalise the raw
metal concentrations in the Tema Harbour sediments to the <63 µm fraction as described in
section 6.2.6.
Table 6.6 shows that the levels of Cd, Pb, Cr, Ni, Cu, Zn and As in sediments from the MH2
and OFH areas were below their corresponding AL1 values. Thus, in relation to the
investigated metals, dredged materials from the MH2 and OFH areas may fall under category
I, which can be disposed at sea. The levels of Cu in sediments from the MH1 and IFH were
between the AL1 and AL2 values, which are potentially hazardous. Similarly, the levels of
Cd, Cu and Zn in sediments from the CB were between their corresponding AL1 and AL2
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
174
values and are, therefore, potentially hazardous and thus, the disposal of these sediments at
sea is inappropriate.
Table 6.6 Comparison of metal concentrations in Tema Harbour (Ghana) sediments
(normalised to the <63 µm fraction) with Spanish sediment quality action
levels (AL1 and AL2)
Cd Pb Cr Ni Cu Zn As
aMH1 0.1 45 72 27 112 216 9
aMH2 0.1 35 71 25 47 138 12
aOFH 0.2 52 80 29 81 252 13
aIFH 0.4 85 81 26 197 416 14
aCB 1.2 106 64 24 204 768 13
bAL1 1 120 200 100 100 500 80
bAL2 5 600 1000 400 400 3000 200
a Tema Harbour sediments;
b action levels (DelValls et al., 2004); unbold = [metal] < AL1 and
indicates permissible metal levels for sediment disposal at sea; bold = AL1 < [metal] < AL2
and indicates sediments would require further assessment prior to sediment disposal at sea.
6.5. Conclusion
The standard 10-day C. volutator and 28-day H. diversicolor whole-sediment bioassays were
combined with metal (Cd, Pb, Cr, Ni, Cu, Zn and As) concentrations to investigate the
potential ecological hazard, risk and impact of contaminated sediments from the Tema
Harbour. C. volutator was found more vulnerable than H. diversicolor to the toxicity effects
the Tema Harbour sediments and underscores the importance of using different of species in
whole-sediment toxicity bioassays. The concentrations of Cu and Zn may play a role in the
mortalities of C. volutator and H. diversicolor. A logarithmic correlation was observed
between sediment Cd concentration and C. volutator mortality, while a linear correlation was
observed between sediment Cu concentration and H. diversicolor mortality. Risk assessment
based on sediment quality guidelines indicated that the metal contamination in the Tema
Harbour sediments poses moderate to high potential ecological risks. The results indicate a
need to improve environmental management and regulate the disposal of dredged materials at
the Tema Harbour.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
175
References
Adams, M.S., & Stauber, J.L., 2008. Marine whole sediment toxicity tests for use in temperate
and tropical Australian environments: current status. Aust. J. Ecotoxicol. 14, 155-167.
Adams, W.J., Blust, R., Borgmann, U., Brix, K.V., DeForest, D.K., Green, A.S., Meyer, J.S.,
McGeer, J.C., Paquin, P.R., & Rainbow, P.S., 2011. Utility of tissue residues for
predicting effects of metals on aquatic organisms. Integr. Environ. Assess. Manage. 7,
75-98.
Annicchiarico, C., Biandolino, F., Cardellicchio, N., Di Leo, A., Giandomenico, S., & Prato,
E., 2007. Predicting toxicity in marine sediment in Taranto Gulf (Ionian Sea, Southern
Italy) using Sediment Quality Guidelines and a battery bioassay. Ecotoxicol. 16, 239-
246.
Aydin-Onen, S., Kucuksezgin, F., Kocak, F., & Açik, S., 2015. Assessment of heavy metal
contamination in Hediste diversicolor (OF Müller, 1776), Mugil cephalus (Linnaeus,
1758), and surface sediments of Bafa Lake (Eastern Aegean). Environ. Sci. Pollut.
Res. 22, 8702-8718.
Bat, L., 2005. A review of sediment toxicity bioassays using the amphipods and polychaetes.
Turkish J. Fish. Aquat. Sci. 5, 119-139.
Bat, L., & Raffaelli, D. (1998). Sediment toxicity testing: a bioassay approach using the
amphipod Corophium volutator and the polychaete Arenicola marina. J. Exp. Mar.
Bio. Ecol. 226, 217-239.
Birch, G.F., & Hutson, P., 2009. Use of sediment risk and ecological/conservation value for
strategic management of estuarine environments: Sydney estuary, Australia. Environ.
Manage. 44, 836-850.
Blott, S.J., Croft, D.J., Pye, K., Saye, S.E., & Wilson, H.E., 2004. Particle size analysis by
laser diffraction. Geol. Soc. Spec. Publ. 232, 63-73.
Botwe, B. O., Kelderman, P., Nyarko, E., & Lens, P.N.L., 2017. Assessment of DDT, HCH
and PAH contamination and associated ecotoxicological risks in surface sediments of
coastal Tema Harbour (Ghana). Mar. Pollut. Bull. 115, 480-488.
Burgess, R.M., Perron, M.M., Cantwell, M.G., Ho, K.T., Pelletier, M.C., Serbst, J.R., & Ryba,
S.A., 2007. Marine sediment toxicity identification evaluation methods for the anionic
metals arsenic and chromium. Environ. Toxicol. Chem. 26, 61-67.
Burton Jr, G.A., 2002. Sediment quality criteria in use around the world. Limnology, 3, 65-76.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
176
Carvalho, S., Cunha, M.R., Pereira, F., Pousão-Ferreira, P., Santos, M., & Gaspar, M., 2012.
The effect of depth and sediment type on the spatial distribution of shallow soft-
bottom amphipods along the southern Portuguese coast. Helgol. Mar. Res. 66, 489-
501.
Casado-Martínez, M.C., Buceta, J.L., Belzunce, M.J., & DelValls, T.A., 2006. Using
sediment quality guidelines for dredged material management in commercial ports
from Spain. Environ. Int. 32, 388-396.
Casado-Martinez, M.C., Forja, J.M., & DelValls, T.A., 2007. Direct comparison of amphipod
sensitivities to dredged sediments from Spanish ports. Chemosphere, 68, 677-685.
Ciarelli, S., Vonck, W., Van Straalen, N., & Stronkhorst, J., 1998. Ecotoxicity assessment of
contaminated dredged material with the marine amphipod Corophium volutator. Arch.
Environ. Contam. Toxicol. 34, 350-356.
de Boer, J., van der Zande, T. E., Pieters, H., Ariese, F., Schipper, C. A., van Brummelen, T.,
& Vethaak, A. D. (2001). Organic contaminants and trace metals in flounder liver and
sediment from the Amsterdam and Rotterdam harbours and off the Dutch coast. J.
Environ. Monit. 3, 386-393.
DelValls, T., Andres, A., Belzunce, M., Buceta, J., Casado-Martinez, M., Castro, R., Riba, I.,
Viguri, J.R., & Blasco, J., 2004. Chemical and ecotoxicological guidelines for
managing disposal of dredged material. Trends Anal. Chem. 23, 819-828.
Durou, C., Poirier, L., Amiard, J.-C., Budzinski, H., Gnassia-Barelli, M., Lemenach, K.,
Peluhet, L., Mouneyrac, C., Roméo, M., & Amiard-Triquet, C., 2007. Biomonitoring
in a clean and a multi-contaminated estuary based on biomarkers and chemical
analyses in the endobenthic worm Nereis diversicolor. Environ. Pollut. 148, 445-458.
Eggen, R.I., Behra, R., Burkhardt-Holm, P., Escher, B.I., & Schweigert, N., 2004. Challenges
in ecotoxicology. Environ. Sci. Technol. 38, 58A-64A.
Eisentraeger, A., Hund-Rinke, K., & Roembke, J., 2004. Proposal of a testing strategy and
assessment criteria for the ecotoxicological assessment of soil or soil materials. J. Soils
Sediments, 4, 123-128.
EPA, USACE, 1998. Evaluation of dredged material proposed for discharge in waters of the
US-testing manual: Inland Testing Manual. EPA-823-B-98-004. US Environmental
Protection Agency and US Army Corps of Engineers, Washington, DC.
Ferretti, J.A., Calesso, D.F., & Hermon, T.R., 2000. Evaluation of methods to remove
ammonia interference in marine sediment toxicity tests. Environ. Toxicol. Chem. 19,
1935-1941.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
177
Forrester, G.E., Fredericks, B.I., Gerdeman, D., Evans, B., Steele, M.A., Zayed, K.,
Schweitzer, L.E., Suffet, I.H., Vance, R.R., & Ambrose, R.F., 2003. Growth of
estuarine fish is associated with the combined concentration of sediment contaminants
and shows no adaptation or acclimation to past conditions. Mar. Environ. Res. 56,
423-442.
Gaion, A., Sartori, D., Scuderi, A., & Fattorini, D., 2014. Bioaccumulation and
biotransformation of arsenic compounds in Hediste diversicolor (Muller 1776) after
exposure to spiked sediments. Environ. Sci. Pollut. Res. 21, 5952-5959.
Hannewijk, A., Kater, B.J., Schipper, C.A., 2004. Sediment toxiciteitstest met Nereis
diversicolor (In Dutch). 22 pp.
Horowitz, A. J., 1985. A primer on trace metal-sediment chemistry, U.S. Geological Survey
Water-Supply Paper 2277, 67 p.
ICES, 2008. Report of the Fourth ICES/OSPAR Workshop on Integrated Monitoring of
Contaminants and their Effects in Coastal and Open Sea Areas (WKIMON IV). ICES
Document CM 2008/ACOM: 49. 71 pp.
Igari, Y., Ohno, M., Tamura, T., Suzuki, K., Kose, T., & Kawata, K., 2012. Chemical
speciation of metals in surface sediments from small urban and agricultural rivers.
Bull. Environ. Contam. Toxicol. 89, 764-769.
Iqbal, J., Tirmizi, S., & Shah, M., 2013. Statistical apportionment and risk assessment of
selected metals in sediments from Rawal Lake (Pakistan). Environ. Monit. Assess.
185, 729-743.
Jain, C., 2004. Metal fractionation study on bed sediments of River Yamuna, India. Water
Res. 38, 569-578.
Kater, B.J., Dubbeldam, M., & Postma, J.F., 2006. Ammonium toxicity at high pH in a marine
bioassay using Corophium volutator. Arch. Environ. Contam. Toxicol. 51, 347-351.
Kelderman, P., 2012. Sediment pollution, transport, and abatement measures in the city canals
of delft, The Netherlands. Water Air Soil Pollut. 223, 4627-4645.
Lepland, A., Andersen, T.J., Lepland, A., Arp, H.P.H., Alve, E., Breedveld, G.D., & Rindby,
A., 2010. Sedimentation and chronology of heavy metal pollution in Oslo harbor,
Norway. Mar. Pollut. Bull. 60, 1512-1522.
Long, E., Macdonald, D., Smith, S., & Calder, F., 1995. Incidence of adverse biological
effects within ranges of chemical concentrations in marine and estuarine sediments.
Environ. Manage. 19, 81-97.
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
178
Long, E.R., Ingersoll, C.G., & MacDonald, D.D., 2006. Calculation and uses of mean
sediment quality guideline quotients: a critical review. Environ. Sci. Technol. 40,
1726-1736.
Marsden, I., & Rainbow, P., 2004. Does the accumulation of trace metals in crustaceans affect
their ecology - the amphipod example? J. Exp. Mar. Bio. Ecol. 300, 373-408.
Mayor, D.J., Solan, M., Martinez, I., Murray, L., McMillan, H., Paton, G.I., & Killham, K.,
2008. Acute toxicity of some treatments commonly used by the salmonid aquaculture
industry to Corophium volutator and Hediste diversicolor: Whole sediment bioassay
tests. Aquaculture, 285, 102-108.
Mestres, M., Sierra, J., Mösso, C., & Sánchez-Arcilla, A., 2010. Sources of contamination and
modelled pollutant trajectories in a Mediterranean harbour (Tarragona, Spain). Mar.
Pollut. Bull. 60, 898-907.
Moreira, S.M., Lima, I., Ribeiro, R., & Guilhermino, L., 2006. Effects of estuarine sediment
contamination on feeding and on key physiological functions of the polychaete
Hediste diversicolor: laboratory and in situ assays. Aquat Toxicol. 78, 186-201.
Mukherjee, A., Rao, K.M., & Ramesh, U. (2009). Predicted concentrations of biocides from
antifouling paints in Visakhapatnam Harbour. J. Environ. Manag. 90, S51-S59.
Nyarko, E., Fletcher, A., Addo, S., Foli, B.A.K., & Mahu, E., 2014. Geochemical assessment
of heavy metals in surface sediments: A case study of the Tema Port, Ghana. J. Ship
Ocean Eng. 4, 79-92.
Petrosillo, I., Valente, D., Zaccarelli, N., & Zurlini, G., 2009. Managing tourist harbors: Are
managers aware of the real environmental risks? Mar. Pollut. Bull. 58, 1454-1461.
Philippe, S., Leterme, C., Lesourd, S., Courcot, L., Haack, U., & Caillaud, J., 2008.
Bioavailability of sediment-borne lead for ragworms (Hediste diversicolor)
investigated by lead isotopes. Appl. Geochem. 23, 2932-2944.
Pueyo, M., Rauret, G., Lück, D., Yli-Halla, M., Muntau, H., Quevauviller, P., & Lopez-
Sanchez, J., 2001. Certification of the extractable contents of Cd, Cr, Cu, Ni, Pb and
Zn in a freshwater sediment following a collaboratively tested and optimised three-
step sequential extraction procedure. J. Environ. Monit. 3, 243-250.
Ré, A., Freitas, R., Sampaio, L., Rodrigues, A.M., & Quintino, V., 2009. Estuarine sediment
acute toxicity testing with the European amphipod Corophium multisetosum Stock,
1952. Chemosphere, 76, 1323-1333.
Roddie, B., & Thain, J., 2002. Biological effects of contaminants: Corophium sp. sediment
bioassay and toxicity test: International Council for the Exploration of the Sea. ICES
Integrated Hazard, Risk and Impact Assessment of Tropical Marine Sediments from Tema Harbour (Ghana)
179
Techniques in Marine Environmental Sciences No. 28, ISSN 0903-2606, Copenhagen,
Denmark.
Scaps, P., 2002. A review of the biology, ecology and potential use of the common ragworm
Hediste diversicolor (OF Müller)(Annelida: Polychaeta). Hydrobiologia, 470, 203-
218.
Scarlett, A., Rowland, S., Canty, M., Smith, E., & Galloway, T., 2007. Method for assessing
the chronic toxicity of marine and estuarine sediment-associated contaminants using
the amphipod Corophium volutator. Mar. Environ. Res. 63, 457-470.
Schipper, C.A., Burgess, R.M., van den Dikkenberg, L.C., 2006. Sediment toxiciteittest met
de slijkgarnaal Corophium volutator (In Dutch). 18 pp.
Schipper, C. A., Lahr, J., Van den Brink, P. J., George, S. G., Hansen, P.-D., de Assis, H. C.
d. S., Van der Oost, R., Thain, J.E., Livingstone, D., & Mitchelmore, C., 2009. A
retrospective analysis to explore the applicability of fish biomarkers and sediment
bioassays along contaminated salinity transects. ICES J. Mar. Sci. 66, 2089-2105
Schipper, C., Rietjens, I., Burgess, R., & Murk, A., 2010. Application of bioassays in
toxicological hazard, risk and impact assessments of dredged sediments. Mar. Pollut.
Bull. 60, 2026-2042.
Schipper, C. A., Leonards, P. E. G., Klamer, H. J., Thomas, K. V., & Vethaak, A. D., 2013.
Protocol for measuring dioxin-like activity in environmental samples using in vitro
reporter gene DR-Luc assays. ICES Techniques in Marine Environmental Sciences
No. 55. 21 pp.
Stronkhorst, J., Schipper, C., Brils, J., Dubbeldam, M., Postma, J., & van de Hoeven, N.
(2003). Using marine bioassays to classify the toxicity of Dutch harbor sediments.
Environ. Toxicol. Chem. 22, 1535-1547.
Thain, J., & Bifield, S., 2002. Biological effects of contaminants: sediment bioassay using the
polychaete Arenicola marina: International Council for the Exploration of the Sea.
Uwadiae, R.E. (2010). An inventory of the benthic macrofauna of Epe Lagoon, southwest
Nigeria. J. Sci. Res. Develop. 12, 161-171.
van den Heuvel-Greve, M., Postma, J., Jol, J., Kooman, H., Dubbeldam, M., Schipper, C., &
Kater, B., 2007. A chronic bioassay with the estuarine amphipod Corophium
volutator: Test method description and confounding factors. Chemosphere, 66, 1301-
1309.
Chapter 7
Settling Fluxes and Sediment
Accumulation Rates by the
Combined Use of Sediment Traps
and Sediment Cores in Tema
Harbour (Ghana)
A modified version of this chapter was published as: Botwe, B.O., Abril, J.M., Schirone, A.,
Barsanti, M., Delbono, I., Delfanti, R., Nyarko, E., & Lens, P.N.L. (2017). Settling fluxes and
sediment accumulation rates by the combined use of sediment traps and sediment cores in
Tema Harbour (Ghana). Science of the Total Environment, 609, 1114-1125.
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
182
Abstract
Settling fluxes and sediment accumulation rates in coastal Tema Harbour (Ghana) were
investigated by the combined analyses of results in sediment traps and sediment cores.
Sediment traps were deployed at 5 stations within the Tema Harbour at 2 sampling depths and
were retrieved every two weeks till the end of 12 weeks to estimate the Settling Fluxes (SFs).
Four sediment cores from the harbour were analysed for their radioactivity (7Be,
234Th,
210Pb,
212Pb,
226Ra,
40K and
137Cs) profiles to quantify Sediment Accumulation Rates (SARs). The
sediment cores exhibited variable bulk density profiles, indicating highly dynamic and non-
steady sedimentation conditions. 7Be-derived gross-estimates of very recent SARs using the
constant flux-constant sedimentation (CF-CS) model were in the range of 2.5-9.0 g.cm-2
.y-1
.
These values were much lower than the estimated average SFs (15.2-53.8 g.cm-2
.y-1
),
indicating sediment resuspension plays an important role. On a decadal time scale,
conventional 210
Pb sediment dating models did not allow any estimation of SARs in the Tema
Harbour. Thus, the 210
Pb-based TERESA model was applied to depict a reliable scenario for
sedimentation with time-averaged SARs in the range of 1.4-3.0 g.cm-2
.y-1
and fluxes of matter
contributed by the marine inflow and local sources. Sediment accretion rates of 1.7-3 cm.y-1
were also inferred, which may pose a moderate problem of sustainability for the Tema
Harbour. This study reveals how the geochemical behaviour of different radionuclides with
Gamma spectrometry in the marine environment can be used to obtain reliable information on
the complex dynamics of Suspended Particulate Matter (SPM), even in a very disturbed and
anthropic environment as a coastal harbour area where (1) conventional 210
Pb-based dating
methods fail and (2) the use of sediment traps and 234
Th and 7Be profiles in sediment cores
show serious constraints.
7.1. Introduction
Coastal marine harbours support national economies through shipping, fishing and tourism
and are, therefore, considered important assets for coastal nations (Van Rijn, 2005). Coastal
marine harbours are prone to large influxes of sediments as a result of waves and tidal
currents (Leys and Mulligan, 2011), as well as erosion downdrift of the harbour breakwater.
In semi-enclosed coastal harbours, the restricted water movement may enhance the settling of
sediments and result in their accumulation within the harbour basin (Lepland et al., 2010;
Botwe et al., 2017a). Sediment accumulation in harbours poses navigation and ecological
challenges (Syvitski et al., 2005; Van Rijn 2005; Green and Coco, 2014), requiring dredging
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
183
at high costs (Qu and Kelderman, 2001; Barneveld and Hugtenburg, 2008; Schipper et al.,
2010). Human activities around harbours often result in the accumulation of a variety of
hazardous pollutants in sediments (Botwe et al. 2017a, 2017b), which poses serious concerns
about the handling and fate of the dredged materials. Sedimentation in harbours is thus a
major issue and its quantification is essential for harbour management (Buesseler et al., 2007;
Leys and Mulligan, 2011).
Information on sediment accumulation rates (SARs) in harbours, reservoirs, estuaries and
coastal areas can be obtained from the comparison of bathymetric data acquired at different
periods (Khaba and Griffiths, 2017, Brucker et al., 2007). This GIS-bathymetric approach
involves measurements of tidal levels, water depth, positioning and the application of a series
of corrections. For shallow waters with less than 20 m water depth such as harbours,
bathymetric data can be best obtained by using Phase Differencing Bathymetric Sonar
(PDBS) systems with an associated total vertical uncertainty of 0.26 m for a 10 m water depth
(Brisson et al., 2014). Although this uncertainty is acceptable for water depth control
purposes, it is too coarse for estimating SARs. Thus, GIS-bathymetry has been mainly used
for mapping SAR in areas where accretion rates are high (>0.3 m.y-1
) (Brucker et al., 2007) or
when the study involves time lapses of the order of decades (Ortt et al., 2000). It is worth
noting that the method provides mean SAR in the time lapse and it cannot identify processes
affecting the depth distribution of hazardous pollutants. Other methods based on horizon
markers, anchored tiles, rulers, sediment traps, optical backscatter sensors and short-lived
radionuclides (234
Th and 7Be) are available for measuring sediment accumulation over short-
time scales (Thomas and Ridd, 2014).
In depositional environments, where continuous accumulation of sediments has taken place
over a long period of time without any interruption in the sedimentary sequence or mixing, the
210Pb sediment dating technique has proven useful for quantifying SARs on time scales
spanning 100-150 years (Appleby and Oldfield, 1978; Robbins, 1978; Appleby and Oldfield,
1983; Caroll and Lerche, 2003; Alonso-Hernandez et al., 2006; Díaz-Asencio et al., 2011;
Bellucci et al., 2012). Sedimentation in coastal marine harbours is, however, a dynamic
process for which relatively large spatial and temporal variations can be expected (Leys and
Mulligan, 2011). For example, sediment resuspension due to wave action, tidal oscillations,
movement of vessels and dredging (Lepland et al., 2010; Leys and Mulligan, 2011; Green and
Coco, 2014) may co-occur with sediment deposition in coastal marine harbours. Thus,
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
184
complete recovery of radionuclide inventories could also be difficult in areas with relatively
high SARs (of the order of 1 g.cm-2
.y-1
) due to the limited length of sediment core samplers.
Quantifying sedimentation rates in such disturbed environments, therefore, requires integrated
approaches (Bellucci et al., 2012), the application of robust numerical models and an accurate
study of the harbour and the operations within the harbour itself (Tanner et al., 2000; Tang et
al., 2008; Smith et al., 2009; Lepland et al., 2010).
As far as we know, there are no previous studies on harbours located in tropical Africa, where
in addition to the aforementioned challenges and the scarcity of background studies, it is
difficult to measure artificial radionuclides such as 137
Cs above the method detection limit due
to its low fallout rate. 210
Pb-based chronologies require independent chronostratigraphic
markers for validation (Smith, 2001; Caroll and Lerche, 2003; Abril, 2004) and 137
Cs is the
most widely used complement for the 210
Pb dating method.
Profiles of short-lived and particle-reactive radionuclides such as 234
Th (half-life = 24 d) and
7Be (half-life = 53 d) in sediment cores can be used to estimate recent sedimentation rates
over short-time scales of days to months (Giffin and Corbett, 2003). 234
Th is produced from
the decay of 238
U (half-life = 4.5 x 109 y), while
7Be is a cosmogenic radionuclide produced
from the interaction of cosmic rays with oxygen and nitrogen in the stratosphere and the
troposphere (Sharma et al., 1987; Erten, 1997; Pfitzner et al., 2004; Palinkas et al., 2005). In
marine environments, 238
U is found in the water column in excess with respect to 226
Ra due to
its higher solubility (IAEA, 2004; Botwe et al., 2007b). When 238
U decays to 234
Th, this high
particle-reactive isotope is taken up by Suspended Particulate Matter (SPM) and surface
sediments, where it can be found in excess with respect to the background levels, referred to
as excess 234
Th (234
Thexc). 7Be and
234Thexc profiles, when combined with
210Pb and
137Cs
profiles in sediment cores, are useful for understanding sediment dynamics in aquatic systems
(Sharma et al., 1987; Erten, 1997; Fuller et al., 1999; Giffin and Corbett, 2003; Palinkas et al.,
2005; Yeager et al., 2005; Schmidt et al., 2007a; Schmidt et al., 2007b). In addition to
radionuclide profiles in sediment cores, sediment traps are important tools for investigating
short-term fluxes and dynamics of sediments in aquatic systems (Kelderman, 2012;
Kelderman et al., 2012; de Vicente et al., 2010).
The objective of this study was to investigate settling fluxes and sedimentation rates in the
coastal marine Tema Harbour (Ghana) by the combined analyses of accumulated dry mass in
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
185
sediment traps and radionuclide (7Be,
234Th,
210Pb,
212Pb,
226Ra,
40K and
137Cs) profiles in
sediment cores, with the help of numerical sediment dating models. In particular, excess 210
Pb
(210
Pbexc) data were analysed with the TERESA (Time Estimates from Random Entries of
Sediments and Activities) model (Abril, 2016), which is based on a widely observed statistical
correlation between 210
Pbexc fluxes and SARs (Abril and Brunskill, 2014). The TERESA
model has been validated against synthetic cores and real data from varved sediments, for
which an independent chronology was available. The basic assumptions of the TERESA
model were satisfied by the sedimentary conditions in the disturbed Tema Harbour, which
provided a unique opportunity to test the performance of this new dating tool under conditions
where the assumptions of most of the 210
Pb-based models fail. Thus, this study may be of
interest to the broad scientific community concerned with the investigation of sedimentation
conditions and pollution records in harbours and other dynamic systems where SAR values
fall beyond the capabilities of the differencing GIS-bathymetry and conventional 210
Pb-based
dating methods, and the use of sediment traps and 234
Th and 7Be profiles show serious
constraints.
7.2. Materials and methods
7.2.1. Study area
The Tema Harbour is about 70 km west from the outlet of the Volta River in Ghana and there
are several minor riverine systems along the Ghanaian shoreline that deliver important loads
of suspended particulate matter to the coastal region (Akrasi, 2011). However, there is no
direct riverine inflow in the Tema Harbour (Botwe et al., 2017b). The Tema Harbour layout
and its operations have been described previously (Botwe et al., 2017a; Botwe et al., 2017b;
Botwe et al., 2017c). Briefly, the Tema Harbour is a semi-enclosed coastal harbour situated in
the Gulf of Guinea at Tema (Greater Accra, Ghana) with a water area of 1.7 km2 (Fig. 7.1). It
has been in operation since 1962 and is partitioned into a Main Harbour, a Fishing Harbour
(Inner and Outer) and a Canoe Basin. The Main Harbour is concerned with shipping
operations and has water depths ranging from 7.5 to 11.4 m (mean 8.5 m), a 240 m wide
entrance and a breakwater of 4850 m length (Botwe et al., 2017b). The Fishing Harbour and
the Canoe Basin are dedicated to the operations of semi-industrial, industrial and artisanal
fishing vessels (Botwe et al., 2017c).
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
186
Fig. 7.1 Map of Tema Harbour (Ghana) showing sediment core and sediment trap
sampling stations and the approximate area dredged in 2014.
The average water temperature is around 23 ºC with water salinity ranging from 30-35‰
(Botwe et al., 2017c). Tides in the study area are semi-diurnal with a tidal range of about 1.6
m. In the immediate coastal sea area, tidal currents range from less than 0.1 to 0.5 m.s-1
and
wave heights range from 1 to 2 m (http://open_jicareport.jica.go.jp/pdf/11681632_03.pdf). A
portion of the Main Harbour (shown in Fig. 7.1) was dredged in March-April 2014, while the
Canoe Basin was dredged in May 2013 (Botwe et al., 2017c). It is also worth noting that in
2013, the construction of a new wharf was started near the eastern margin of the dredged area,
with the emplacement of the supporting concrete pillars. The over-water structure was
completed during 2014.
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
187
7.2.2. Sediment sampling
Four sediment cores were sampled with an Uwitech® gravity corer (length = 60 cm; internal
diameter = 8.5 cm) from stations A, B, C and D in the Tema Harbour (Fig. 7.1) in April 2015.
Water depths at the sediment core stations A, B, C and D were 8.5, 8, 10 and 9 m,
respectively. During the sediment core sampling period, the turbidity of seawater
was measured in Nephelometric Turbidity Unit (NTU) at the surface, mid depth and the
bottom at each core sampling station using a turbidity probe (HI 9829, Hanna Instruments,
USA).
Besides, vertical arrays of 2 cylindrical polyvinyl chloride (PVC) sediment traps, positioned
0.6 m apart in an alternating fashion, were deployed at 5 stations (I, II, III, IV and V) along a
transect in a less busy area of the Tema Harbour (Fig. 7.1) over a period of 12 weeks (23 May
- 15 August, 2015) to collect settling particles at two water depths of approximately 1.8 m
(top trap) and 0.6 m (bottom trap) from the seabed. The aspect ratio of each sediment trap was
6.0 (i.e. height = 60 cm; diameter = 10 cm) to minimise current-induced resuspension and loss
of material from the trap (Bloesch & Burns, 1980; Kelderman et al., 2012; de Vicente et al.,
2010). The sediment traps were retrieved every two weeks (Kelderman, 2012; Kelderman et
al., 2012; de Vicente et al., 2010) till the end of the 12-week period. Upon their retrieval, the
sediment cores and trap samples were placed upright in racks and transported to the
Department of Marine and Fisheries Sciences laboratory at the University of Ghana for further
processing and analysis. Rainfall data over the study period was obtained from the Ghana
Meteorological Services.
In the laboratory, the sediment cores were allowed to stand overnight, after which the
overlying water was carefully siphoned off. Each sediment core was sectioned at 1 cm
intervals over the top 2 cm layer and subsequently at 2 cm intervals. During core extrusion
and sectioning, lower sections may become contaminated as they move past smears from
upper sections left on the walls of the corer. Thus, the outer 1 cm rim of each sediment slice
was trimmed off (Bellucci et al., 2012). The content of each sediment trap was wet-sieved
successively over 2000 and 63 µm stainless steel mesh sieves to determine the distribution of
the <63 µm (silt-clay) and 63-2000 µm (sand) fractions of the trapped sediment. The wet
weights of the sediment core samples, the core layers, as well as the <2000 µm fraction of
sediment trap samples were measured and then oven-dried at 50°C till constant weight to
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
188
obtain their dry weights (Botwe et al., 2017b). Direct gamma spectrometric analyses of 7Be
(478 keV), 234
Th (63.3 keV), 210
Pb (210
Pbtot, 46.5 keV), 212
Pb (239 keV), 214
Pb (352 keV), 214
Bi
(609 keV), 137
Cs (662 keV) and 40
K (1460 keV) were performed at ENEA Marine
Environment Research Centre (S. Teresa, Italy). Prior to the gamma analyses, the sediment
core samples were homogenised by grinding and stored air-tight for at least 22 days in plastic
vials of standard geometries (5, 10 and 20 g) following Botwe et al. (2017b) to ensure secular
equilibrium between the parent nuclides and their short-lived daughter nuclides. The
measured activities were decay-corrected to the sediment sampling date.
7.2.3. Data treatment
Sediment trap-derived settling fluxes (SF, with units of g.cm-2
.y-1
) were estimated from Eq. 1:
( )
where M is the dry accumulated mass of trapped material (g), A is the cross-sectional area of
the sediment trap (cm2) and D is the duration of trap deployment (y).
The water content of the sediment samples was obtained from the difference between the wet
and dry weights and expressed as a percentage of the sediment wet weight. The 226
Ra
activities were indirectly obtained from the average 214
Pb and 214
Bi activities (Botwe et al.,
2017b). For each sediment layer, the 210
Pbexc specific activity was obtained by subtracting the
226Ra (supported
210Pb) specific activity from the total
210Pb (
210Pbtot) specific activity (Corbett
et al., 2009). Excess 234
Th (234
Thexc) specific activity was estimated from the total 234
Th
specific activity by subtracting the background level (the averaged value of concentrations
measured downcore, except the topmost layers). Core D required a more complex procedure,
since the values measured downcore were not constant. The supported 234
Th fraction near the
surface was estimated by assuming a constant 238
U/226
Ra ratio along the whole core. Bulk
densities were evaluated from the determination of the dry weight of the mass contained in a
well controlled bulk volume of the sediment, and the mass depths at the centre and at the
bottom of each sediment slice determined following Baskaran et al. (2014).
Subsurface sediments may undergo compaction and introduce errors in the determination of
sediment depth and age relationships and hence, the estimation of linear sedimentation rates
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
189
(Abril, 2003; Lu, 2007). Therefore, the activity profiles of 7Be,
234Thexc and
210Pbexc
were
related to the mass-depth (mass of sediment per unit area, g.cm-2
) instead of the linear-depth
of the sediment (Erten, 1997; Lu, 2007). Inventories of 7Be were determined for each core by
integrating their downcore activities (Giffin and Corbett, 2003; Mullenbach et al., 2004;
Palinkas et al., 2005). The simplest SAR modelling approach, defined by the assumptions of
constant flux and constant sedimentation rate (CF-CS) without any post-depositional
redistribution (Appleby and Oldfield, 1983; Erten, 1997), was applied to the sediment cores to
derive very recent (3-8 months) SARs based on the measured 7Be activity profiles.
The TERESA model was applied for the analysis of 210
Pbexc versus mass depth profiles. The
model fundamentals and its validation against synthetic cores and real data from varved
sediments have been described by Abril (2016). In summary, the model stands on the
following set of assumptions: (i) 210
Pbexc behaves as a particle-associated tracer and new
inputs are ideally deposited over the previously existing material; (ii) there is no post-
depositional redistribution; (iii) there is continuity of the sequence (i.e., there is not any
missing layer by erosion); and (iv) 210
Pbexc fluxes are governed by ‗horizontal inputs‘ and
thus, there is a statistical correlation between 210
Pbexc fluxes and SAR (Abril and Brunskill,
2014). Therefore, for a sediment core which has been sectioned into N slices of mass
thickness Δmi (i = 1, 2, ... N), each slice has an associated age interval ΔTi, a mean SAR value (wi),
and an associated initial specific activity (A0,i) corresponding to the activity when that
sediment slice was at the sediment-water-interface (SWI).
The TERESA model operates with SAR and initial radionuclide activity distributions, for
respectively, wi and A0,i, which closely follow normal distributions around their arithmetic
mean values, w and Ᾱ0, with standard deviations σw and σA, respectively. Sw and SA are,
respectively, their normalised values (standard deviation over mean values). Provided a first
estimation of w , Ᾱ0, σw and σA, the model generates independent random distributions for wi
and A0,i; and then an intelligent algorithm solves their best arrangement downcore to fit the
experimental 210
Pbexc versus the mass depth profile, generating then solutions for the
chronological line and for the histories of SAR and sediment fluxes (Abril, 2016). As the
result depends on the first estimation of w , Ᾱ0, σw and σA, the model applies a mapping
technique by iterating the whole process for each parameter varying over a wide range. The
error function, Q2, measures the overall quality of the fit for each individual run of the model
(Abril, 2016):
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
190
N
i i
iithfQ
AAQ
1
22
2
2
,2 /;)(
(2)
where Ai and σi are, respectively, the measured value and the analytical error of the
radionuclide specific activity at the slice with index i, Ath,i being the corresponding value
estimated by the model, χ is a measure of the mean distance between the theoretical and
experimental profiles in terms of the size of the associated uncertainties, and f is the number
of degrees of freedom.
Parametric maps of the χ-function serve to find out the best solution and to support error
estimates (Abril, 2016). The typical fundamentals can be applied for error estimates in the
four entry parameters (namely w , σw, Ᾱ0, σA) through the curvature of the parametric lines in
the Q2 function around the position of the absolute minimum (Bevington and Robinson,
2003). The associated uncertainty in the age at the bottom of each layer, Tj, can then be
estimated through the general propagation law:
2222
2 )()()()()(
w
w
j
A
A
j
m
m
j
m
m
j
j
TTw
w
TA
A
TT
(3)
Optionally, the model's answers can be better constrained through the use of time markers,
when available. As the model-algorithm requires a continuous profile, data from the non-
measured sediment slices have been estimated by linear interpolation with ascribed double
error-bars to minimise their relative weight in the fit. To avoid the generation of negative
values or influencing points when exploring large values of Sw and SA, lower threshold limits
of 0.1 Ᾱ0 and 0.2 w have been imposed in all the calculations.
7.3. Results and discussion
7.3.1. Estimates of settling fluxes of particulate matter in the Tema Harbour
Table 7.1 shows the estimated average settling fluxes (SFs) of particulate matter over two
sampling depths (top and bottom traps) in the Tema Harbour based on the accumulated dry
mass in the sediment traps retrieved every two weeks till the end of the 12-week sampling
period. The average SF values over the two sampling depths ranged from 15 (± 3) to 54 (± 18)
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
191
g.cm-2
.y-1
, being higher at stations III and IV. About 93% of these SFs (range 84%-96%)
correspond to the fraction of particle sizes larger than 63 μm (Table 7.1). As the typical
settling velocities for fine sand and larger particle sizes are over 10 m.h-1
(Eisma, 1993; Ji,
2008), they will be quickly removed from the water column.
Table 7.1 Estimated settling fluxes (SFs) of particulate matter (mean ± standard
error) at five sampling stations in the Tema Harbour (Ghana) based on biweekly
accumulated dry mass in sediment traps deployed at two water depths (top and
bottom traps) over a period of 12 weeks. The weight fraction (%) of the trapped
sediment samples with Ф<63 µm are also presented. See sampling stations in Fig.
7.1.
Sampling
station
Sediment trap
deployment
SF
(g.cm-2
.y-1
)
Fraction with
Ф< 63 μm (%)
I Top trap
1 18 ± 11 8.1
Bottom trap2 21 ± 7 7.6
II Top trap
2 25 ± 5 9.4
Bottom trap2 15 ± 3 8.7
III Top trap
2 46 ± 16 3.8
Bottom trap2 42 ± 12 3.9
IV Top trap
2 54 ± 18 4.5
Bottom trap2 23 ± 8 16.1
V Top trap
2 30 ± 13 6.3
Bottom trap2 28 ± 9 5.2
1 n = 3;
2 n = 6
From the maximum tidal range of 1.6 m
(http://www.tides4fishing.com/af/ghana/tema#_tide_table) and the geometry of the Main
Harbour entrance (i.e. 240 m width and 8.5 m mean water depth), it is possible to estimate a
maximum cross-sectional averaged water current of about 6 cm.s-1
at the Main Harbour
entrance, and a bottom shear stress slightly over 0.07 Pa by applying standard hydrodynamic
principles (Periáñez and Abril, 2014; Abril and Periáñez, 2016). This estimated shear stress,
which is associated with maximum tidal currents at the Tema Harbour, is over the threshold
value (0.06 Pa) for resuspending clays and fine silts (Eisma, 1993; Ji, 2008). But in the inner
area of the Main Harbour, the tidal currents are lower and resuspension of sediments is not
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
192
expected to occur because of the tidal forcing. Nevertheless, ship traffic and particularly the
manoeuvres of big cargos and drilling ships can cause remobilisation of large amounts of
sediments, as it can be seen from available aerial photographs (e.g. 10/08/2015; Google
Earth). Thus, coexistence of sediment deposition and resuspension is expected to occur.
Consequently, the obtained SFs may overestimate the SAR values since the material settled
within the sediment traps is not allowed to undergo resuspension, which could occur in real
sediments. Thus, the estimated time-averaged SFs from the top and bottom sediment traps at
each station represent only a proxy and an upper bound of the expected annually-averaged
values at their locations.
Concerning temporal variations, some relative maxima were found at different periods for
each station (not shown). The SF values from the top sediment traps were usually comparable
or higher than those from the bottom traps, although some exceptions were found at stations I
and V. The observed maxima found at different periods for each station did not correspond to
a single event of entry of a high mass inflow into the Main Harbour. Moreover, maxima of
SFs at the two sampling depths at each sampling station are often registered at different times.
This fact points out the importance of local disturbances, which have a highly irregular
character both in time and space, and are most likely linked to the manoeuvring of cargo
ships. Moreover, from the location of the sampling points, it is expected that station I, at a
corner of the Main Harbour, should experience less perturbations and thus capturing lower
masses of SF, as indeed found in Table 7.1. This reveals a complex dynamics of rising clouds
of suspended particulate matter (SPM) and settling in the Tema Harbour, interfered by
horizontal transport, most likely the one forced by the tidal dynamics.
The mean (± standard deviation) turbidity values of the surface, mid depth and bottom
seawater at the sediment core sampling stations were as follows: core station A = 3.9 (± 0.8)
Nephelometric Turbidity Unit (NTU); B = 3 (± 0.6) NTU; C = 3.7 (± 0.7) and D = 4.7 (± 1.1).
Although a station-specific ppm (mg.L-1
) versus NTU calibration curve was not constructed,
from a typical slope of 3.4 ppm/NTU, the turbidity measurements lead to an estimation of the
SPM concentration, C, of around 10 parts per million (ppm). Assuming that this value is
representative of the mean environmental conditions at the Tema Harbour and using the SF
values in Table 7.1 (i.e. CvSF s ), the mean values for the settling velocities, vs, were
estimated to be in the range of (0.5-1.7)10-3
m.s-1
, again corresponding to silt and fine sand
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
193
fractions. These considerations could also provide a gross estimate of the order of magnitude
of the expected mean sedimentation rates in the Tema Harbour. From the known tidal range
and mean water depth, one could estimate that in each tidal cycle, the Tema Harbour
exchanges about 10% of its water volume. If the above SPM concentration of 10 ppm is
representative of the marine inflow and the Tema Harbour acts as a huge sediment trap, the
expected mean SAR value would be about 6 g.cm-2
.y-1
. Large local variability is expected
around this value due to localised discharge of solids, ship traffic and varying sedimentation
yields.
It is worth noting that the SF values from Table 7.1 captured the prevailing environmental
conditions in the SW area of the Tema Harbour during the 12-week deployment period. They
represent an upper bound for the sediment mass accumulation rates (SARs) at their respective
sampling stations. Rainfall in the sampling area during the sampling period and the preceding
month ranged from 0 to 142.3 mm with a mean of 6.1 mm (not shown). There were no
episodic incidents of heavy rainfall, storm runoff or floods during the study period, which
could have induced sediment transport into the Tema Harbour and affect the sedimentary
regime (Palinkas et al., 2005; Díaz-Asencio et al., 2011).
7.3.2. Radionuclide and bulk density profiles in sediment cores from Tema Harbour
The mass depth and 7Be,
234Th,
210Pb,
226Ra,
212Pb and
137Cs specific activity profiles of cores
A, B, C and D from the Tema Harbour are shown in Table 7.2, while Fig. 7.2 shows the bulk
density versus depth profiles for the cores. Table 7.2 shows that cores A, B and C had similar
radionuclide trends, with almost constant downcore 210
Pbtot specific activity (around 200-300
Bq.kg-1
), while core D showed large differences in the radionuclide activity profiles with
lower activities at intermediate depths (from approximately 15 to 25 cm). For all the cores, the
210Pbexc and
137Cs specific activity profiles did not reach a zero value in the deeper layers.
Moreover, no clearly decreasing 210
Pbexc profiles were observed in all four sediment cores.
Fig. 7.2 shows that bulk density in cores A and B exhibit similar and typical quasi-steady
compaction profiles broken by some intermediate relative peaks. Core C showed a trend of
increasing bulk density downcore with anomalous low values at the top 0-2 cm layer. Core D
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
194
Table 7.2 Profiles of mass depth and radioactivity (7Be, 234Th, 210Pbtot, 226Ra, 212Pb,
40K and 137Cs) concentrations in sediment cores from Tema Harbour
(Ghana). See sampling stations in Fig. 7.1.
Specific activities (Bq kg-1
)
Core
ID
Core
depth
(cm)
*Cumulative
mass depth
(g.cm2)
7Be
234Th
210Pbtot
226Ra
212Pb
40K
137Cs
A 0-1 0.65 50 ± 9 135 ± 34 296 ± 13 15 ± 2 40 ± 1 317 ± 18 < 0.6
1-2 1.27 29 ± 7 94 ± 32 302 ± 10 12 ± 2 41 ± 1 304 ± 17 < 0.6
2-4 2.39 20 ± 6 28 ± 6 279 ± 10 13 ± 2 36 ± 1 288 ± 15 1.9 ± 0.5
4-6 4.28 6 ± 3 32 ± 4 319 ± 10 15 ± 1 42 ± 1 313 ± 13 2.1 ± 0.4
6-8 5.45 5 ± 3 36 ± 4 286 ± 9 14 ± 1 44 ± 1 333 ± 14 1.4 ± 0.4
8-10 6.62 < 6 35 ± 4 251 ± 7 16 ± 1 47 ± 1 336 ± 14 2.0 ± 0.3
10-12 7.69 < 6 31 ± 4 314 ± 9 15 ± 1 28 ± 1 294 ± 11 1.0 ± 0.3
12-14 9.13 < 6 35 ± 3 309 ± 10 15 ± 1 26 ± 1 309 ± 10 1.6 ± 0.3
16-18 12.67 < 6 30 ± 4 300 ± 9 15 ± 1 25 ± 1 271 ± 12 1.7 ± 0.4
24-26 17.30 < 6 39 ± 3 330 ± 9 17 ± 1 25 ± 1 292 ± 10 1.4 ± 0.2
32-34 22.13 < 6 33 ± 3 282 ± 7 15 ± 1 25 ± 1 294 ± 9 1.5 ± 0.3
B 0-1 0.55 61 ± 14 206 ± 30 285 ± 20 11 ± 2 46 ± 3 360 ± 31 <1
1-2 1.34 17 ± 9 84 ± 46 233 ± 17 13 ± 2 45 ± 2 329 ± 27 2.6 ± 1.0
2-4 2.71 <9 32 ± 6 245 ± 14 14 ± 1 43 ± 1 323 ± 17 2.1 ± 0.6
4-6 3.91 <9 43 ± 6 298 ± 15 14 ± 1 29 ± 1 291 ± 15 1.8 ± 0.5
6-8 5.1 <9 34 ± 9 298 ± 18 16 ± 2 29 ± 1 295 ± 21 1.8 ± 0.7
8-10 7.3 <9 35 ± 6 284 ± 14 14 ± 1 26 ± 1 285 ± 12 2.0 ± 0.4
12-14 10.0 <9 40 ± 6 298 ± 15 14 ± 1 27 ± 1 326 ± 15 1.7 ± 0.4
16-18 12.2 <9 40 ± 6 222 ± 12 13 ± 1 28 ± 1 320 ± 17 0.9 ± 0.4
22-24 16.6 <9 34 ± 5 175 ± 10 14 ± 1 37 ± 1 324 ± 13 1.8 ± 0.3
28-30 20.8 <9 29 ± 5 165 ± 10 15 ± 1 37 ± 1 340 ± 14 2.2 ± 0.5
C 0-1 0.26 55 ± 10 196 ± 19 258 ± 17 10 ± 2 48 ± 2 325 ± 28 2.1 ± 0.9
1-2 0.65 54 ± 12 278 ± 25 276 ± 17 13 ± 2 49 ± 2 375 ± 28 <1
2-4 2.06 25 ± 5 95 ± 16 242 ± 14 13 ± 1 42 ± 1 314 ± 11 1.2 ± 0.4
4-6 3.39 <12 36 ± 3 289 ± 16 14 ± 1 43 ± 1 341 ± 11 1.1 ± 0.3
6-8 4.74 <12 32 ± 4 302 ± 18 14 ± 1 45 ± 1 341 ± 12 1.0 ± 0.4
8-10 6.31 <12 30 ± 3 182 ± 12 15 ± 1 60 ± 1 396 ± 13 1.3 ± 0.4
12-14 9.92 <12 34 ± 5 177 ± 13 15 ± 1 59 ± 1 373 ± 15 1.1 ± 0.5
14-16 11.89 <12 31 ± 5 187 ± 14 15 ± 1 53 ± 1 406 ± 17 1.9 ± 0.5
16-18 14.14 <12 28 ± 4 155 ± 10 15 ± 1 51 ± 1 453 ± 13 <1
18-20 16.10 <12 37 ± 4 190 ± 12 17 ± 1 62 ± 1 413 ± 15 1.0 ± 0.3
32-34 30.95 <12 37 ± 3 203 ± 12 13 ± 1 34 ± 1 404 ± 12 1.3 ± 0.3
40-42 41.10 <12 37 ± 4 219 ± 13 14 ± 1 35 ± 1 402 ± 12 1.7 ± 0.5
46-48 48.8 <12 31 ± 5 207 ± 10 16 ± 1 32 ± 1 421 ± 15 1.5 ± 0.3
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
195
Table 7.2 Continued
Specific activities (Bq.kg-1
)
Core
ID
Core
depth
(cm)
*Cumulative
mass depth
(g.cm2)
7Be
234Th
210Pbtot
226Ra
212Pb
40K
137Cs
D 0-1 0.38 126 ± 31 219 ± 37 276 ± 16 17 ± 3 39 ± 1 333 ± 19 2.4 ± 0.8
1-2 0.94 48 ± 7 276 ± 38 284 ± 13 15 ± 2 40 ± 1 340 ± 19 <1.2
2-4 2.12 34 ± 9 234 ± 40 269 ± 13 11 ± 2 37 ± 1 321 ± 18 <1.2
4-6 3.27 19 ± 5 107 ± 15 242 ± 10 12 ± 2 35 ± 1 299 ± 14 <1.2
6-8 4.82 <6 47 ± 14 217 ± 13 9 ± 2 28 ± 1 302 ± 18 <1.2
8-10 6.41 <6 25 ± 3 200 ± 8 11 ± 2 25 ± 1 270 ± 13 1.3 ± 0.4
12-14 10.87 <6 16 ± 3 82 ± 6 7 ± 1 16 ±
0.5 266 ± 11 <0.6
16-18 17.22 <6 7 ± 2 18 ± 4 5 ± 1 11 ±
0.3 275 ± 9 <0.6
20-22 24.33 <6 9 ± 3 41 ± 6 4 ± 1 14 ±
0.4 318 ± 13 0.6 ± 0.3
26-28 33.85 <6 17 ± 2 79 ± 5 9 ± 1 21 ±
0.4 280 ± 10 0.8 ± 0.2
36-38 48.10 <6 13 ± 2 86 ± 6 7 ± 1 17 ±
0.4 299 ± 11 <0.6
38-40 49.73 <6 24 ± 4 182 ± 7 12 ± 1 28 ±
0.6 337 ± 12 1.0 ± 0.3
Errors are 1 standard deviation from counting statistics; Minimum Detectable Activity are
indicated as < MDA (Bq.kg-1
); *At the central point of each sediment slice
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
196
Fig. 7.2 Bulk density (ρ) versus depth profiles for sediment cores A, B, C and D
sampled from Tema Harbour (Ghana)
showed a distinct structure, with higher values of bulk density below the 15 cm depth. Thus,
the data on bulk density suggest highly dynamic and non-steady sedimentary conditions at the
study site (Abril, 2003). It is worth noting that high values of bulk density are typically
associated with the presence of coarser grain-sizes, which have lower specific activities of
surface-bound radionuclides.
7.3.3. Inventories and fluxes of 7Be and 7Be-derived sediment accumulation rates
The measurement of 7Be specific activities in the top layer of a sediment core is usually
considered as a quality test for the complete surface recovery of the core, which is necessary
for dating (Erten et al., 1985; Erten, 1997). In the Tema Harbour, it was possible to measure
7Be in several sediment slices downcore (Table 7.2). This provided an opportunity to
determine the very recent SAR values over the past 6-8 months under some simplifying
assumptions. The 7Be inventories (see Table 7.3) ranged from 470 (± 110) to 1360 (± 170)
Bq.m-2
, core D being richer in 7Be than the other cores. The
7Be inventories in the Tema
Harbour sediments were higher, but comparable to the values reported by Olsen et al. (1985)
for coastal sediments from Virginia and Tennessee (370-740 Bq.m-2
). The 7Be inventories in
the Tema Harbour sediments were also comparable to, but lower than the values reported for
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0 10 20 30 40 50
ρ (
g.c
m-3
)
Depth (cm)
Core A Core B Core C Core D
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
197
(1) sediments of the Neuse and Pamlico River Estuaries (33-97 Bq.m-2
) by Giffin and Corbett
(2003), (2) sediments of the Eel Canyon, northern California (5,780-12,000 Bq.m-2
) by
Mullenbach et al. (2004), and (3) sediments from Po River delta, Adriatic Sea (190-5,420
Bq.m-2
) by Palinkas et al. (2005). The fluxes of 7Be onto the SWI, assumed to be constant,
were estimated from the product of the 7Be inventories and the radioactive decay constant.
They varied from 2200 (± 500) to 6500 (± 800) Bq.m-2
.y-1
(Table 7.3). The spatial variability
in 7Be values in the Tema Harbour may be due to the fact that uptake of atmospheric
7Be by
SPM mediates its fluxes onto the SWI. A large spatial variability in 7Be inventories is a
common feature of coastal sediments, which has been previously reported in the scientific
literature (Rose and Kuehl, 2010; Kolker et al., 2012).
Table 7.3 7Be inventories and fluxes onto the sediment-water interface (SWI) and
7Be-derived sediment accumulation rate (SAR) values in sediment cores
From Tema Harbour (Ghana).
Core
7Be inventory
(Bq.m-2
)
7Be flux onto SWI
(Bq.m-2
.y-1
)
7Be-derived SAR*
(g.cm-2
.y-1
)
A 900 ± 120 4300 ± 600
9.0 ± 1.3
B 470 ± 110 2200 ± 500
2.5 ± nd
C 710 ± 90 3400 ± 400
7.1 ± 1.8
D 1360 ± 170 6500 ± 800
7.1 ± 2.0
*From a CF-CS model; nd: not determined
Fig. 7.3 shows that 7Be versus mass depth profiles in sediment cores A and D followed an
exponential decay at a confidence level of over 90%, while for cores B and C the number of
data points is not statistically significant. Table 7.3 reports the 7Be-derived SAR values,
assuming the applicability of the CF-CS model. The SAR values were in the range of 2.5-9.0
g.cm-2
.y-1
, and were much lower than the sediment trap-derived SFs (Table 7.1). This
observation points out the important role of sediment resuspension in the sedimentation
process at the Tema Harbour, as expected from the aerial photographs (see Section 7.3.1).
Nevertheless, these values have to be taken as a first estimate of the order of magnitude of
SARs in Tema Harbour. The reported uncertainties in Table 7.3 come from a numerical fitting
which does not account for the uncertainties in the radionuclide specific activities. But "the
model errors" arising from a partial accomplishment of the involved assumptions may be
more relevant. Thus, the 7Be versus mass-depth profiles could be mediated by mixing,
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
198
diffusion or non-ideal depth deposition of fluxes, which would result in somewhat lower SAR
values than the above estimates. Particularly, the assumption of a constant flux is problematic
for 7Be due to its short half-life (Taylor et al., 2013).
It has been shown for different geographical latitudes that the atmospheric deposition of 7Be is
well correlated with rainfall (Pham et al., 2013). Rainfall in southern Ghana is higher during
the rainy season (April-June and September-October) and minimum during the dry season
(November-March and July-August). Unusually high rainfall values of about 100 mm were
recorded for both February and March 2015, while only 30-40 mm was recorded in January
2015 (https://jbaidoowilliams.com/2015/10/20/el-nino-2015-rainfall-fears/). Although a
Fig. 7.3 7Be versus mass depth profiles of sediment cores A, B, C and D sampled
from Tema Harbour (Ghana). Error bars represent 1-σ counting uncertainties.
system time-averaged integration of fluxes has been described (Robbins, 2000), the
assumption of constant fluxes of 7Be may be an oversimplification. On the other hand, the
short penetration depth of 7Be in the core makes its profile more sensitive to surficial
processes such as the non-ideal deposition described by Abril and Gharbi (2012).
The 234
Th activity versus mass depth profiles (Table 7.2) showed a near-constant background
level along the cores at the 2-3 cm upper sediment slices. This is consistent with the high SAR
values estimated from the 7Be data.
0
1
2
3
4
5
6
0 1 2 3 4
Ln
[A
(7B
e)]
[Ln
(Bq k
g-1
)]
Mass depth (g cm-2)
Core A Core B Core C Core D
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
199
7.3.4. Analysis of 210Pbexc fluxes onto the SWI and mixing
From Table 7.2, the surficial specific activities of 210
Pbexc (~300 Bq.kg-1
) were over one order
of magnitude higher than those reported by Nyarko et al. (2016) for sediment cores from the
Pra and Volta estuaries in Ghana. The difference can be explained in terms of the
granulometry of the sediments, with a large component of the inputs linked to the small grain-
size SPM supplied by the tidal inflow. For the theoretical basis of the relationship among
radionuclide specific activities and particle size, see Abril and Fraga (1996) and Abril (1998).
The analysed cores were too short to allow any reliable estimation of the total 210
Pbexc
inventories required for the application of the constant rate of supply (CRS) model. The low
values and large uncertainties in the 137
Cs data did not allow any proper identification of
chronostratigraphic horizons. Moreover, cores A, C and D did not follow any clear monotonic
exponential trend of decrease (Fig. 7.4) and thus, the application of the CF-CS model for
deriving SAR values was not reliable.
The SAR values derived from 7Be data, along with the
210Pbexc specific activities in the upper
sediment layers can be used to obtain a first estimate of the 210
Pbexc fluxes onto the SWI if any
post-depositional remobilization is discarded. Thus, for core A, this resulted in a flux onto the
SWI of 25.6 kBq.m-2
.y-1
, being two orders of magnitude higher than the expected atmospheric
deposition of 210
Pbexc in the Tema Harbour area (typically in the range of 100-200 Bq.m-2
.y-1
).
This means that fluxes of 210
Pbexc onto the SWI must be governed by fluxes of matter (Abril
and Brunskill, 2014). Furthermore, the models handling high diffusion coefficients and null or
low SAR values under steady-state conditions could roughly fit the profiles from cores A, B
and C (not shown). However, these models require fluxes of up to 100 kBq.m-2
.y-1
to enter
into the SWI (mostly in the dissolved form), which cannot be supplied by atmospheric
deposition.
About mixing, on the other hand, no observational evidence of bioturbation was available that
would induce sediment mixing over large mass depths. Some degree of horizontal and vertical
mixing may, nevertheless, exist due to the remobilization forced by ship displacements. But as
data from sediment traps integrate a large number of such events, mixing in the sediments is
not expected to exceed the 1-2 cm surface layer. About 70 vessels enter and leave the Tema
Harbour weekly, most of them being cargo, tug and tanker vessels; and they follow well-
defined tracks within the harbour
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
200
(http://www.marinetraffic.com/en/ais/details/ports/86/Ghana_port:TEMA). In contrast, the
depth profiles of 7Be and
234Th in the sampling sites showed sharp gradients in the 0-2 cm
layers, which are not compatible with a well-mixed layer. The hypothesis of mixing can thus
be discarded as a main governing factor to explain the observed profiles. As the cores were
sampled out of the dredged area (Fig. 7.1), they must have preserved a sequence of continuous
sediment deposition.
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
201
0
50
100
150
200
250
300
350
0 10 20 30
210P
bexc (
Bq.k
g-1
)
Mass depth (g.cm-2)
a (Core A) Data
0
50
100
150
200
250
300
350
0 10 20 30
210P
bexc (
Bq.k
g-1
) Mass depth (g.cm-2)
b (Core B) Data
0
50
100
150
200
250
300
350
0 20 40 60
210P
bexc (
Bq.k
g-1
)
Mass depth (g.cm-2)
c (Core C) Data
0
50
100
150
200
250
300
0 20 40 60
210P
bexc (
Bq.k
g-1
)
Mass depth (g.cm-2)
d (Core D) Data
Fig. 7.4 210Pbexc versus mass depth profile for (a) core A, (b) core B, (c) core C and
(d) core D in the Tema Harbour (Ghana). Vertical bars correspond to the associated
uncertainties (1-σ), while the horizontal ones define the mass depth interval of each
sediment slice. The numerical solution generated by the TERESA model is plotted as
points at the centre of each slice interval (continuous line is only for guiding-eyes).
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
202
7.3.5. Analyses of 210Pb profiles and estimation of SARs using the TERESA model
The hypothesis of varying, but statistically correlated, fluxes of matter and 210
Pbexc onto the
SWI seems reasonable for the Tema Harbour and thus, the conditions for applying the
TERESA model can be met. Maps for the χ function (described in Section 7.2.3) in the ( 0A ,
w ) and (SA - SW) spaces for the four studied cores were computed with the TERESA model
(not shown). The computation was done with the stand-alone version of the model and with
the basic method-A (Abril, 2016), and they show relatively well defined valleys which
determine the parameter values along with their associated fitting uncertainties, reported in
Table 7.4. The computed 210
Pbexc vs. mass depth profiles are shown in Fig. 7.4(a-d), and they
match the experimental data with the χ values reported in Table 7.4. Finally, the resulting
chronologies for the four cores are shown in Fig. 7.5.
Table 7.4 Entry parameters of the TERESA model and fitting-error estimates1 for the
investigated cores from the Tema Harbour, where 0A (Bq.kg-1) is the mean
initial concentration, ̅ is the mean SAR value (g.cm-2.y-1) and SA, Sw are
the corresponding relative standard deviations.
1 Through the second derivative of the Q
2 function (Bevington and Robinson, 2003)
Core 0A w SA Sw χ
A 364.0 ± 0.2 1.620 ± 0.008 0.175 ± 0.003 0.384 ± 0.006 1.90
B 262.0 ± 1.0 1.87 ± 0.07 0.169 ± 0.009 0.322 ± 0.024 0.96
C 253.0 ± 1.2 3.27 ± 0.21 0.200 ± 0.010 0.27 ± 0.08 0.61
D 152.5 ± 0.1 4.080 ± 0.004 0.600 ± 0.001 0.990 ± 0.003 1.09
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
203
Fig. 7.5 Chronologies estimated by the TERESA model for the investigated sediment
cores from the Tema Harbour (Ghana) along with their corresponding uncertainty
intervals (from the propagation of error associated to the fitting parameters of Table
7.4).
7.3.6. Analyses of sediment cores A, B and C
Data from sediment core A showed the highest values of 210
Pbexc specific activities and they
remained almost constant downcore. The TERESA model produced a reasonable fit to the
data with arithmetic means of 364 Bq kg-1
and 1.62 g.cm-2
.y-1
and normalised standard
deviations of 0.175 and 0.384 for the initial specific activity and SAR, respectively. It is worth
noting that there were no alternative valley regions in the χ surface, and the fit, although not
especially good, was well constrained, as inferred from the low fitting uncertainties (which are
related to the curvature of the χ-surface along the parametric lines). There was a trend of
decreasing radionuclide specific activities in recent dates, which compensates for the
radioactive decay in the deeper layers and explains the observed profile. The age of the
deepest measured sediment slice (32-34 cm) was estimated at 16 y, which implies a time-
averaged SAR of 1.4 g.cm-2
.y-1
(or 2.1 cm.y-1
). The time-averaged SAR is used likewise the
CRS dating model in order to make these values comparable with literature data.
0
5
10
15
20
25
30
0 10 20 30 40 50 60
Age
(y)
Mass depth (g.cm-2)
Core A Core B Core C Core D
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
204
The chronological line generated by the TERESA model for sediment core B ran close to the
one from core A (Fig. 7.5), with a slightly higher value of SAR and lower initial radionuclide
specific activity (arithmetic means of 1.87 g.cm-2
.y-1
and 262 Bq kg-1
, respectively). The age
of the deepest measured sediment slice (28-30 cm) was estimated at 13 y, which implies a
time-averaged SAR of 1.6 g.cm-2
.y-1
(or 2.4 cm.y-1
).
Sediment core C showed a 210
Pbexc profile with a distinct sub-surface peak followed by a
plateau area, and it was well reproduced by the TERESA model (Fig. 7.4c). The arithmetic
mean value for the initial specific activity was close to the one for sediment core B, but the
SAR value was noticeably higher. The age of the deepest measured sediment slice (46-48 cm)
was estimated at 16 y (with a time-averaged SAR of 2.9 g.cm-2
.y-1
or 3.0 cm.y-1
). The distinct
peak extended up to a mass-depth of 4.06 g.cm-2
, for which the TERESA-derived age was 1.5
(± 0.5) y (Fig. 7.5). The building of the wharf structure between 2013 and 2014 might have
changed the local sedimentological conditions. Under the new conditions, the radionuclides
content in sediment core C tends to the values found in sediment core A (see Table 7.2). This
implies that before the deployment of the pillars, the fluxes of matter on the site of sediment
core C were contributed by both marine inflow and some local sources, which resulted in
higher bulk densities (Fig. 7.2), higher SAR (Table 7.4), lower 210
Pbexc activity content and
some higher 40
K specific activities (see Table 7.2). The sharp discontinuity in radionuclides
profiles at the mass-depth of 4.06 g.cm-2
confirms the hypothesis of negligible post
depositional processes.
7.3.7. Analysis of sediment core D
Sediment core D showed a complex 210
Pbexc profile with high specific activities around 270
Bq.kg-1
at the top layers, which decline till 13 Bq.kg-1
at a mass depth of 17 g.cm-2
and then
increase downcore till 170 Bq.kg-1
(Fig. 7.4d). The area with low 210
Pbexc specific activities
was associated with high values of bulk density (Fig. 7.2). The TERESA model was able to
reasonably reproduce the complex 210
Pbexc profile of sediment core D (χ = 1.09, see Fig. 7.4d)
with arithmetic means of initial activities and SAR which are roughly 2/5 and 5/2 of the ones
found for sediment core A (Table 7.4). A large variability was ascribed to both values with
reference normalised standard deviations of 0.60 and 0.99, respectively. The computed initial
specific activities was plotted versus mass depths to display a U-shape with a minimum mass
depth around 17-21 g.cm-2
(age 11-13 y). This induced a huge dilution effect, most likely
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
205
attributable to local sources of matter with negligible 210
Pbexc content, so the mean value of the
flux onto the SWI was 6.2 kBq.m-2
.y-1
, as in sediment core A. As in the case of sediment core
C, these local sources also resulted in higher bulk densities (Fig. 7.2) and the overall higher
SAR (Table 7.4). The variability in SAR was very high, but randomly distributed, which
resulted in a relatively uniform chronological line (Fig. 7.5). The age of the deepest measured
sediment slice (38-40 cm) was estimated at 24 y, which implies a time-averaged SAR of 2.1
g.cm-2
.y-1
(or 1.7 cm.y-1
).
The above interpretation can be further supported by the analysis of the 234
Thexc profile in
sediment core D. When excluding the topmost layers, the 234
Th concentrations were almost
constant downcore with almost uniform 234
Th/226
Ra isotopic ratios, having mean (± standard
deviation) values of 2.24 (± 0.17), 2.57 (± 0.45), 2.28 (± 0.33) and 1.72 (± 0.15) for sediment
cores A, B, C and D, respectively. When comparing the concentrations of 234
Th and 226
Ra
along the four sediment cores, it is striking to note that in core D, their values were about a
factor of 2 lower in the central layers associated with low values of 210
Pbexc and high bulk
density values. The low radionuclide specific activities, while keeping the isotopic ratios, can
only be explained by the dilution of naturally settling material with other sources of matter. A
similar effect of dilution is observed for 226
Ra and 212
Pb isotopes, which show an increasing
rend in the top sediment layers (Fig. 7.6). This means that the dilution effect progressively
vanished during the last six years, according to the chronology reported in Fig. 7.5. Their
concentrations at the recent SWI converge to the ones found for sediment core A (see Table
7.2). The dilution was not so apparent for 40
K (Fig. 7.6) and thus this radionuclide should be
present in the local source of matter at concentrations somewhat lower than those found in
sediment core A.
The reported uncertainties in the entry parameters of the TERESA model (Table 7.4) came
from the fitting procedure, while the ones reported with the chronologies (Fig. 7.5) came from
their propagation. As with all the models, there are other sources of uncertainty associated
with the partial accomplishment of the model assumptions. In the TERESA model, the
reference normal distributions for initial activities and SAR (truncated with the minimum
threshold values) are only a proxy to the real ones occurring in nature. The incomplete
sequence of measurements make interpolations necessary, and the absence of independent and
well distributed chronostratigraphic marks did not allow the use of the complete model
capabilities (Abril, 2016).
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
206
Fig. 7.6 Normalised (to their maximum value) 226Ra, 212Pb and 40K specific activities
versus mass depth for sediment core D sampled from the Tema Harbour (Ghana).
7.3.8. Comparison of SAR values among sediment cores A, B, C and D
Despite the above limitations, the TERESA model was able to depict a good scenario for the
sedimentation in the Tema Harbour, with overall SAR values with time-averages in the range
of 1.4-3.0 g.cm-2
.y-1
. The analysed sediment core lengths were too short and only captured the
last 13-24 years of sedimentation (extreme values for sediment cores B and D, respectively).
Sediment cores A and B seemed to capture the less perturbed conditions, and they were
governed by the marine inflow of SPM with higher 210
Pbexc specific activities and most likely
linked to a finer granulometry. The TERESA model captured a change in the sedimentary
conditions for sediment core C, whose age is in reasonable agreement with the time of
deployment of the concrete pillars of the new wharf structure. According to the model results,
the previous sedimentary environment around sediment core C also received matter with
lower radionuclide activity content from local sources, leading to high SAR and high bulk
densities. A more extreme change in sedimentary conditions was observed for the sediment
core D site, which is located in the harbour area transited by cargo ships. Here, the TERESA
model reproduced a noticeable dilution effect also attributable to the mixing of the marine
0
0.2
0.4
0.6
0.8
1
1.2
0 5 10 15 20
Norm
alis
ed
226R
a,
212P
b a
nd
40K
sp
ecific
activitie
s
Mass depth (g.cm-2)
226-Ra 212-Pb 40-K
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
207
inflow of SPM with local sources of matter that had low specific activities of 210
Pbexc, 226
Ra,
234Th and
212Pb.
7.3.9. Comparison of the TERESA- and 7Be-derived SARs
The SAR values derived from the TERESA model were of the same order, but noticeably
lower than those estimated from the 7Be data. As discussed above, the assumption of a
constant flux may be an oversimplification for 7Be and so the SAR was not constant. The
overestimation of SAR calculated by 7Be is most likely the major effect of a mass-depth
penetration of a fraction of the 7Be fluxes (non-ideal deposition as described by Abril and
Gharbi, 2012). A fraction of the radiotracer flux crossing the SWI exists in dissolved form or
attached to small grain-size fractions. This fraction can penetrate through the connected water
pores and be distributed at depth instead of being deposited over the previously existing
material. This effect has been widely observed for 7Be in soils (Taylor et al., 2013), riverine
floodplain sediments (Sommerfield et al., 1999), and in marine environments (Rose and
Kuehl, 2010). Thus, as a demonstration of the concept, Fig. 7.7 plots the results from a
numerical simulation for the 7Be distribution in core A using the SAR value from the
TERESA model, and a non-ideal deposition described by factors g = 0.5 and α = 0.6 g-1
.cm2
(see Abril and Gharbi, 2012). The plot was compared against the corresponding exponential
decline from a CF-CS model with ideal deposition under the same sedimentological
conditions. Figure 7.7 confirms non-ideal deposition may seriously limit the applicability of
short-lived radionuclides to radiometric dating of recent sediments, while its effects less
affected 210
Pbexc: it produced slight distortions in the upper layers, where subsurface maxima
are often found (Abril and Gharbi, 2012). The TERESA model compensates for these effects
on the 210
Pbexc profile through an equivalent variability in initial radionuclide activities and/or
SAR, as shown in Abril (2016) with the TERESA chronology for a varved sediment core
from the Santa Barbara Basin (California, USA) for which non-ideal sediment deposition has
been described by Abril and Gharbi (2012).
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
208
Fig. 7.7 Numerical simulation for the 7Be distribution in sediment core D using the
SAR value from the TERESA model, and a non-ideal deposition described by factors
g = 0.5, α = 0.6 g-1cm2 (see Abril and Gharbi, 2012), and the simplifying assumption
of constant flux. The plot is compared against the corresponding exponential decline
from a CF-CS with ideal deposition under the same sedimentological conditions.
Horizontal bars correspond to the depth intervals.
The time-averaged SAR values found in the tropical coastal Tema Harbour by the TERESA
model (1.4-3.0 g.cm-2
.y-1
) were very high when compared with most of the literature data for
lacustrine and coastal environments from other climatic regions. Accounting for the high bulk
density of the sediments in the Tema Harbour, the accretion rates were in the range of 1.7-3
cm.y-1
. Also, these accretion rates were higher than values reported in the scientific literature
for harbour areas, e.g. 0.57 cm.y-1
in the Tanjung Pelepas Harbour, Malaysia (Yussof et al.,
2015); 1.2 cm.y-1
in the Victoria Harbour, Hong Kong (Tang et al., 2008); 0.2-2 cm.y-1
for
Sydney Harbour, Nova Scotia, Canada (Smith et al., 2009). This implies that typical coring
devices, allowing for core lengths below 1 m may be too short for recovering the whole
210Pbexc inventory. This, along with irregular non-monotonic profiles, seriously limited the
application of most of the conventional 210
Pb-based dating models in the studied Tema
Harbour cores. The accretion rates in the Tema Harbour are, nevertheless, only of moderate
concern for the harbour sustainability, i.e. filling up the harbour basin and imposing a need for
0
50
100
150
200
250
300
350
0 1 2 3 4
7B
e (
Bq k
g-1
)
Mass depth (g.cm-2)
Data Core D
Non-Ideal deposition model
CF-CS model
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
209
dredging. If these conditions had prevailed since its construction in 1962, the net accretion
around the studied sites would have been in the range of 0.9-1.6 m, which is in agreement
with the partial dredging conducted in 2014.
7.4. Conclusions
Settling fluxes and sedimentation rates in coastal Tema Harbour (Ghana) have been
investigated based on accumulated dry mass in sediment traps and radionuclide (7Be,
234Th,
210Pb,
226Ra,
40K,
212Pb and
137Cs) profiles in four sediment cores. The average settling fluxes
ranged from 15 (± 3) to 54 (± 18) g.cm-2
.y-1
, showing spatial and temporal variations from
which a complex dynamics of suspended particulate matter in the Tema Harbour is inferred.
The analysed sediment cores were too short to allow any reliable estimation of SARs in the
Tema Harbour based on the 210
Pbexc inventories and traditional dating models (CF-CS and
CRS). The
210Pb-based TERESA model was successfully applied to depict a good scenario for
sedimentation rates in the Tema Harbour over the past 13-24 y, with overall time-averaged
SAR values in the range of 1.4-3.0 g.cm-2
.y-1
. These SAR values imply sediment accretion
rates of 1.7-3 cm.y-1
in the Tema Harbour, which poses a moderate problem of sustainability
for its management.
References
Abril JM, Brunskill GJ. Evidence that excess 210
Pb flux varies with sediment accumulation
rate and implications for dating recent sediments. J Paleolimnol 2014; 52(3):121-137.
Abril JM, Gharbi F. Radiometric dating of recent sediments: beyond the boundary conditions.
J Paleolimnol 2012; 48(2):449-460.
Abril JM. A new theoretical treatment of compaction and the advective-diffusive processes in
sediments: a reviewed basis for radiometric dating models. J Paleolimnol 2003;
30(4):363-370.
Abril JM. Constraints on the use of 137
Cs as a time-marker to support CRS and SIT
chronologies. Environ Pollut 2004; 129(1):31-37.
Abril JM, Fraga E. Some physical and chemical features of the variability of Kd distribution
coefficients for radionuclides. J Environ Radioact 1996; 30(3):253-270.
Abril JM. Basic microscopic theory of the distribution, transfer and uptake kinetics of
dissolved radionuclides by suspended particulate matter - Part I: Theory development.
J Environ Radioact 1998; 41(3):307-324.
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
210
Abril JM. A 210
Pb-based chronological model for recent sediments with random entries of
mass and activities: Model development. J Environ Radioact 2016; 151:64-74.
Abril JM, Periáñez R. Revisiting the time scale and size of the Zanclean flood of the
Mediterranean (5.33 Ma) from CFD simulations. Mar Geol 2016; 382:242-256.
Akrasi S. Sediment discharges from Ghanaian rivers into the sea. West Afr J Appl Ecol 2011;
18(1):1-13.
Alonso-Hernandez C, Diaz-Asencio M, Muñoz-Caravaca A, Delfanti R, Papucci C, Ferretti
O, Crovato C. Recent changes in sedimentation regime in Cienfuegos Bay, Cuba, as
inferred from 210
Pb and 137
Cs vertical profiles. Cont Shelf Res 2006; 26(2):153-167.
Appleby PG, Oldfield F. The assessment of 210
Pb data from sites with varying sediment
accumulation rates. Hydrobiologia 1983; 103(1):29-35.
Appleby PG, Oldfield F. The calculation of lead-210 dates assuming a constant rate of supply
of unsupported 210
Pb to the sediment. Catena 1978; 5:1-8.
Barneveld H, Hugtenburg J. Feasibility study for implementation of sedimentation reduction
measures in river harbours. RCEM 2008; 1187-1192.
Baskaran M, Nix J, Kuyper C, Karunakara N. Problems with the dating of sediment core
using excess 210
Pb in a freshwater system impacted by large scale watershed changes.
J Environ Radioact 2014; 138:355-363.
Bevington, P. A., Robinson, D.K., 2003. Data Reduction and Error Analysis for the Physical
Sciences, 3rd Edition. McGraw-Hill, New York.
Bellucci LG, Giuliani S, Romano S, Albertazzi S, Mugnai C, Frignani M. An integrated
approach to the assessment of pollutant delivery chronologies to impacted areas: Hg in
the Augusta Bay (Italy). Environ Sci Technol 2012; 46(4):2040-2046.
Bevington PA, Robinson DK. Data Reduction and Error Analysis for the Physical Sciences,
3rd Edition. McGraw-Hill 2003.
Bloesch J, Burns N. A critical review of sedimentation trap technique. Schweiz Z Hydrol
1980; 42(1):15-55.
Botwe BO, Kelderman P, Nyarko E, Lens PNL. Assessment of DDT, HCH and PAH
contamination and associated ecotoxicological risks in surface sediments of coastal
Tema Harbour (Ghana). Mar Pollut Bull 2017a; 115(1–2):480-488.
Botwe BO, Schirone A, Delbono I, Barsanti M, Delfanti R, Kelderman P, Nyarko E, Lens
PNL. Radioactivity concentrations and their radiological significance in sediments of
the Tema Harbour (Greater Accra, Ghana). J Radiat Res Appl Sci 2017b; 10(1):63-71.
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
211
Botwe BO, De Schamphelaere K, Schipper CA, Teuchies J, Blust R, Nyarko E, Lens PNL.
Integrated hazard, risk and impact assessment of tropical marine sediments from Tema
Harbour (Ghana). Chemosphere 2017c; 177:24-34.
Brisson LN, Wolfe DA, Staley M. Interferometric swath bathymetry for large scale shallow
water hydrographic surveys. Canadian Hydrographic Conference 2014; 1-18.
Brucker S, Clarke JH, Beaudoin J, Lessels C, Czotte K, Loschiavo R, Iwanowska K, Hill P.
Monitoring flood-related change in bathymetry and sediment distribution over the
Squamish Delta, Howe Sound, British Columbia. U.S. Hydrographic Conference
2007; 1-16.
Buesseler KO, Antia AN, Chen M, Fowler SW, Gardner WD, Gustafsson O, Harada K,
Michaels AF, Rutgers van der Loeff M, Sarin M. An assessment of the use of
sediment traps for estimating upper ocean particle fluxes. J Mar Res 2007; 65(3):345-
416.Caroll J, Lerche I. Sedimentary Processes: Quantification Using Radionuclides.
Elsevier 2003.
Corbett DR, Walsh JP, Marciniak K. Temporal and spatial variability of trace metals in
sediments of two adjacent tributaries of the Neuse River Estuary, North Carolina,
USA. Mar Pollut Bull 2009; 58(11):1739-1747.
de Vicente I, Cruz-Pizarro L, Rueda FJ. Sediment resuspension in two adjacent shallow
coastal lakes: controlling factors and consequences on phosphate dynamics. Aquat Sci
2010; 72(1):21-31.
Díaz-Asencio M, Alvarado JC, Alonso-Hernández C, Quejido-Cabezas A, Ruiz-Fernández A,
Sanchez-Sanchez M, Hernández-Albernas JI, Eriksson M, Sanchez-Cabeza J.
Reconstruction of metal pollution and recent sedimentation processes in Havana Bay
(Cuba): a tool for coastal ecosystem management. J Hazard Mater 2011;196:402-411.
Eisma D. Suspended Matter in the Aquatic Environment. Springer-Verlag 1993.
Erten H, Von Gunten H, Rössler E, Sturm M. Dating of sediments from Lake Zurich
(Switzerland) with210Pb and137Cs. Swiss J Hydrol 1985; 47(1):5-11.
Erten H. Radiochronology of lake sediments. Pure Appl Chem 1997; 69(1):71-76.
Fuller C, van Geen A, Baskaran M, Anima R. Sediment chronology in San Francisco Bay,
California, defined by 210
Pb, 234
Th, 137
Cs, and 239,240
Pu. Mar Chem 1999; 64(1):7-27.
Giffin D, Corbett DR. Evaluation of sediment dynamics in coastal systems via short-lived
radioisotopes. J Mar Syst 2003; 42(3):83-96.
Green MO, Coco G. Review of wave‐driven sediment resuspension and transport in estuaries.
Rev Geophys 2014; 52(1):77-117.
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
212
IAEA. Sediment distribution coefficients and concentration factors for biota in the marine
environment. Technical Reports Series No. 422. International Atomic Energy Agency
2004.
Ji ZG. Hydrodynamics and Water Quality: Modelling Rivers, Lakes and Estuaries. Wiley
2008.
Kelderman P. Sediment pollution, transport, and abatement measures in the city canals of
delft, The Netherlands. Water, Air, & Soil Pollution 2012; 223(7):4627-4645.
Kelderman P, Ang‘weya R, De Rozari P, Vijverberg T. Sediment characteristics and wind-
induced sediment dynamics in shallow Lake Markermeer, the Netherlands. Aquat Sci
2012; 74(2):301-313.
Khaba L, Griffiths JA. Calculation of reservoir capacity loss due to sediment deposition in
the Muela reservoir, Northern Lesotho. Int Soil Water Conserv Res 2017; 5:130-140.
Kolker AS, Miner MD, Weathers HD. Depositional dynamics in a river diversion receiving
basin: The case of the West Bay Mississippi River Diversion. Estuar Coast Shelf Sci
2012; 106:1-12.
Lepland A, Andersen TJ, Lepland A, Arp HPH, Alve E, Breedveld GD, Rindby A.
Sedimentation and chronology of heavy metal pollution in Oslo Harbour, Norway.
Mar Pollut Bull 2010; 60(9):1512-1522.
Leys V, Mulligan RP. Modelling coastal sediment transport for harbour planning: selected
case studies. INTECH 2011.
Lu X. A note on removal of the compaction effect for the 210
Pb method. Appl Radiat Isot
2007; 65(1):142-146.
Mullenbach B, Nittrouer C, Puig P, Orange D. Sediment deposition in a modern submarine
canyon: Eel Canyon, northern California. Mar Geol 2004; 211(1):101-119.
Nyarko E, Klubi E, Laissaoui A, Benmansour M. Estimating recent sedimentation rates using
lead-210 in tropical estuarine systems: case study of Volta and Pra estuaries in Ghana,
West Africa. J Oceanogr Mar Res 2016; 4(1):141-145
Olsen CR, Larsen IL, Lowry PD, Cutshall NH, Todd JF, Wong GTF, Casey WH.
Atmospheric fluxes and marsh-soil inventories of 7Be and
210Pb. J Geophys Res 1985;
90(D6):10487-10495.
Ortt RA, Kerhin RT, Wells D, Cornwell J. Bathymetric survey and sedimentation analysis of
Loch Raven and Prettyboy reservoirs. Coastal and Estuarine Geology File Report
2000;99-4.
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
213
Palinkas C, Nittrouer C, Wheatcroft R, Langone L. The use of 7Be to identify event and
seasonal sedimentation near the Po River delta, Adriatic Sea. Mar Geol 2005; 222:95-
112.
Periáñez R, Abril JM. A numerical modeling study on oceanographic conditions in the former
Gulf of Tartessos (SW Iberia): Tides and tsunami propagation. J Mar Syst 2014;
139:68-78.
Pfitzner J, Brunskill G, Zagorskis I. 137
Cs and excess 210
Pb deposition patterns in estuarine and
marine sediment in the central region of the Great Barrier Reef Lagoon, north-eastern
Australia. J Environ Radioact 2004; 76(1):81-102.
Pham MK, Povinec PP, Nies H, Betti M. Dry and wet deposition of 7
Be, 210
Pb and 137
Cs in
Monaco air during 1998-2010: Seasonal variations of deposition fluxes. J Environ
Radioact 2013; 120:45-57.
Qu W, Kelderman P. Heavy metal contents in the Delft canal sediments and suspended solids
of the River Rhine: multivariate analysis for source tracing. Chemosphere 2001;
45(6):919-925.
Robbins JA, Holmes C, Halley R, Bothner M, Shinn E, Graney J, Keeler G, tenBrink M,
Orlandini KA, Rudnick D. Time-averaged fluxes of lead and fallout radionuclides to
sediments in Florida Bay. J Geophys Res 2000; 105(C12):28805-28821.
Robbins JA. Geochemical and geophysical applications of radioactive lead isotopes. In:
Nriagu JO (Ed.), Biogeochemistry of Lead. Elsevier (1978).
Rose LE, Kuehl SA, 2010. Recent sedimentation patterns and facies distribution on the
Poverty Shelf, New Zealand. Mar Geol 2010; 270:160-174.
Schipper C, Rietjens I, Burgess R, Murk A. Application of bioassays in toxicological hazard,
risk and impact assessments of dredged sediments. Mar Pollut Bull 2010; 60(11):
2026-2042.
Schmidt S, Jouanneau J-M, Weber O, Lecroart P, Radakovitch O, Gilbert F, Jézéquel D.
Sedimentary processes in the Thau Lagoon (France): from seasonal to century time
scales. Estuar Coast Shelf Sci 2007a; 72(3):534-542.
Schmidt S, Gonzalez J-L, Lecroart P, Tronczyński J, Billy I, Jouanneau J-M. Bioturbation at
the water-sediment interface of the Thau Lagoon: impact of shellfish farming. Aquat
Living Resour 2007b; 20(2):163-169.
Sharma P, Gardner L, Moore W, Bollinger A. Sedimentation and bioturbation in a salt marsh
as revealed by 210
Pb, 137
Cs, and 7Be studies. Limnol Oceanogr 1987; 32(2):313-326.
Settling Fluxes and Sediment Accumulation Rates by the Combined Use of Sediment Traps and Sediment Cores in Tema Harbour (Ghana)
214
Smith J, Lee K, Gobeil C, Macdonald R. Natural rates of sediment containment of PAH, PCB
and metal inventories in Sydney Harbour, Nova Scotia. Sci Total Environ 2009;
407(17):4858-4869.
Smith JN. Why should we believe 210 Pb sediment geochronologies? J Environ Radioact
2001; 55(2):121-123.
Sommerfield CK, Nittrouer CA, Alexander CR. 7Be as a tracer of flood sedimentation on the
northern California continental margin. Conti Shelf Res 1999; 19:335-361.
Syvitski JP, Vörösmarty CJ, Kettner AJ, Green P. Impact of humans on the flux of terrestrial
sediment to the global coastal ocean. Science 2005; 308(5720):376-380.
Tang CW-y, Ip CC-m, Zhang G, Shin PK, Qian P-y, Li X-d. The spatial and temporal
distribution of heavy metals in sediments of Victoria Harbour, Hong Kong. Mar Pollut
Bull 2008; 57(6):816-825.
Tanner PA, Leong LS, Pan SM. Contamination of heavy metals in marine sediment cores
from Victoria Harbour, Hong Kong. Mar Pollut Bull 2000; 40(9):769-779.
Taylor A, Blake WH, Smith HG, Mabit L, Keith-Roach MJ. Assumptions and challenges in
the use of fallout beryllium-7 as a soil and sediment tracer in river basins. Earth Sci
Rev 2013; 126:85-95.
Thomas S, Ridd P. Review of methods to measure short time scale sediment accumulation.
Mar Geol 2014; 207:95-114.
Van Rijn LC. Estuarine and coastal sedimentation problems. Int J Sediment Res 2005;
20(1):39-51.
Yeager K, Santschi P, Phillips J, Herbert B. Suspended sediment sources and tributary effects
in the lower reaches of a coastal plain stream as indicated by radionuclides, Loco
Bayou, Texas. Environ Geol 2005; 47(3):382-395.
Yusoff AH, Zulkifli SZ, Ismail A, Mohamed CAR. Vertical trend of trace metals deposition
in sediment core off Tanjung Pelepas Harbour, Malaysia. Procedia Environ Sci 2015;
30:211-216.
Chapter 8
Settling Fluxes and
Ecotoxicological Risk
Assessment of Fine Sedimentary
Metals in Tema Harbour (Ghana)
A modified version of this chapter was published as: Botwe, B.O., Nyarko, E., & Lens, P.N.L.
(2018). Settling fluxes and ecotoxicological risk assessment of fine sedimentary metals in
Tema Harbour (Ghana). Marine Pollution Bulletin, 126, 119-129.
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
216
Abstract
Sediment traps were deployed in the Tema Harbour to estimate the settling fluxes of silt-clay
particles and associated metals (Fe, Mn, Pb, Cr, Cu, Zn, Ni, Hg, Sn and As) and characterise
their potential ecotoxicological risks. The mean daily settling fluxes of the silt-clay particles
and associated metals ranged from 42.7 to 85.0 g m-2
d-1
and 1.3 x 10-2
to 49.4 mg m-2
d-1
,
respectively, and were characterised by large fluctuations at each station. The silt-clay and
metal fluxes strongly correlated, indicating the important role of the silt-clay particles in metal
transport and distribution in the harbour. Geochemical indices indicated anthropogenic
influences on the harbour as the Pb, Cr, Zn, Hg, Sn and As content in the settling silt-clay
particles exceeded average crustal concentrations. Sediment quality guidelines indicated these
metals pose appreciable ecotoxicological risks, particularly As. Increasing temporal trends in
As necessitates increased pollution control efforts at the harbour.
8.1. Introduction
Many West African coastal states are tapping into the blue economy by the construction of
new harbours along their coasts and expansion of existing ones. These harbours are often sited
close to industrial, urban and agricultural areas that serve as important sources of chemical
contamination, aside contamination from shipping activities within the harbour itself
(Petrosillo et al., 2009; Lepland et al., 2010; Mestres et al., 2010; Schipper et al., 2010; Botwe
et al., 2017a). Chemical contamination in harbours poses a threat to their sustainability as it
can result in adverse impacts such as hindrance to harbour activities, alteration of ecological
habitats, death of marine organisms resulting in loss of biodiversity, decline in productivity,
fishing restrictions, dietary restrictions on seafood (Lepland et al., 2010), increased incidence
of human diseases and high costs of maintenance dredging (Botwe et al., 2017b). Although
environmental issues and sustainability are becoming an integral part of harbour development,
operation and management (Mestres et al., 2010), effective regulation of contaminant
discharges into harbours from diffuse sources still remains a challenge (Petrosillo et al.,
2009), particularly for developing countries. Thus, continuous monitoring and assessment of
chemical contamination in harbours is crucial for their management (Pozza et al., 2004;
Botwe et al., 2017c).
Metals are among the widespread environmental contaminants due to their wide societal use
and applications. Metals such as Pb, Cr, Cu, Zn, Ni, As, Sn and Hg are not only hazardous to
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
217
humans and non-human biota, but are also persistent and bioaccumulative (Casado-Martínez
et al., 2006; Nyarko et al., 2011; Botwe et al., 2017d). Therefore, their contamination deserves
great attention. In aquatic environments, metals are scavenged and accumulated by fine
sedimentary materials, particularly silt-clay (< 63 µm) particles, as a result of their high
sorptive capacity (Horowitz, 1985; Horowitz and Elrick, 1987; Horowitz et al., 1989; Lepland
et al., 2010; Hamzeh et al., 2014). Thus, the silt-clay particles play a major role in the fate of
metals in aquatic ecosystems, including their fluxes, deposition, burial and resuspension
(Hostache et al., 2014; Botwe et al., 2017b). Therefore, in order to adequately address the
problem of metal contamination in aquatic ecosystems, the fine sedimentary materials should
be the prime materials for investigation (Horowitz, 1985). Moreover, information on the
fluxes of fine sedimentary materials and associated metals can provide an insight into recent
anthropogenic influences on the ecosystem under study and hence, the effectiveness of metal
pollution control measures.
Sediment traps, which passively collect and accumulate settling particulates, have proven
useful for the investigation of particulate matter fluxes in lacustrine (Hakanson, 2006; de
Vicente et al., 2010; Kelderman et al., 2012) and marine (Buesseler et al., 2007; Santos-
Echeandía et al., 2012; Liu et al., 2014; Szmytkiewicz and Zalewska, 2014; Helali et al.,
2016) ecosystems. To enhance trap efficiency and minimise loss of trapped material as a
result of current-induced resuspension, sediment traps with aspect ratios (i.e. height/diameter)
> 5 are recommended (Bloesch & Burns, 1980; Kelderman et al., 2012; de Vicente et al.,
2010). Retrieving sediment traps after 2 weeks of deployment is also recommended as it
allows accumulation of sufficient particulate matter, while minimising organic matter
decomposition (Hakanson and Jansson, 1983; Buesseler et al., 2007; Kelderman et al., 2012).
The coastal marine Tema Harbour in Ghana is one of the large harbours in West Africa and
has a long history of urbanisation and industrialisation within its catchments (Botwe et al,
2017b). Due to a lack of regulations on industrial discharges or weak enforcement in Ghana,
the Tema Harbour may act as a repository for contaminants from point and diffuse sources. In
order to understand and minimise anthropogenic impact on the harbour, it is essential to
characterise contaminant fluxes, sources and associated ecotoxicological risks (Pozza et al.,
2004). However, existing literature does not provide information on metal fluxes in the
harbour. The objectives of this study, therefore, were to (1) estimate settling fluxes of silt-clay
particles and associated metals (Mn, Pb, Cr, Cu, Zn, Ni, Hg, Sn and As) in the Tema Harbour,
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
218
(2) quantify the extent of metal contamination in the sediments and (3) characterise the
potential ecotoxicological risks.
8.2. Materials and methods
8.2.1. Study area
The Tema Harbour is situated along the Ghana sea coast at Tema, the industrial city of Ghana
(Botwe et al., 2017c). It was constructed in 1960 to support industrial growth in Ghana and is
partitioned into a Main Harbour, an Inner Fishing Harbour, an Outer Fishing Harbour and a
Canoe Basin (Botwe et al., 2017c) with a water area of 1.7 km2, an average tidal range of 1.6
m and tidal currents in the range of 0.1-0.5 ms-1 (Botwe et al. 2017b). The Main Harbour is
designated for shipping activities and has a 240 m wide entrance, a breakwater of 4850 m
length and water depths in the range of 7.5 to 11.4 m (Botwe et al., 2017b, e). The Fishing
Harbours and the Canoe Basin provide landing and fuel storage facilities that sustain a
productive fishery (Botwe et al., 2017a, d). Notable industrial activities in Tema are crude oil
refining, alumina smelting, paint, steel and cement production (Botwe et al., 2017c). The main
land uses in the Tema metropolis are residential, agricultural (largely subsistence), industrial
and commercial. Industrial effluents, domestic wastes and wastewater from the industrial
areas and other parts of the Tema township may eventually reach the Tema Harbour via
drains, surface runoff and alongshore transport.
8.2.2. Sediment sampling and analyses
The sediment samples were collected as part of a broader study on sedimentation conditions
in the Tema Harbour, in which the sampling methodology has been described (Botwe et al.
2017b). In that study, settling fluxes of bulk sediment in the water column and sediment
accumulation rates in the Tema Harbour were quantified, while the present study quantified
the settling fluxes of only the silt-clay particles and their associated metals as they represent
the most bioavailable and ecologically relevant sediment grain-sizes (Bat and Raffaelli, 1998;
Bat, 2005). Briefly, cylindrical sediment traps made of polyvinyl chloride (PVC) with aspect
ratios of 6.0 were deployed at five stations (I, II, III, IV and V) along a transect in a less busy
area within the Main Harbour (see Fig. 1 in Botwe et al., 2017b), where the water depths
ranged from 9 to 11 m. At each station, a vertical array of two sediment traps, positioned 0.6
m apart in an alternating fashion, were deployed to collect settling particles at two water
depths of approximately 1.8 m (top trap) and 0.6 m (bottom trap) from the seabed. The
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
219
sediment traps were retrieved every two weeks over a period of 12 weeks (23 May - 8 August,
2015). The sediment traps were capped prior to their retrieval in order to keep the trapped
materials intact. A total of 56 sediment trap samples were collected over the study period.
Following retrieval, the sediment traps with their contents were kept in upright positions in a
rack and transported to the Department of Marine and Fisheries Sciences laboratory
(University of Ghana) for further processing and analysis.
In the laboratory, the trapped sediment samples were separated into silt-clay (< 63 µm) and
sand (> 63 µm) particles by wet-sieving over a 63 µm stainless steel mesh and then oven-
dried at 50°C till constant weight (Wang et al., 2001; Botwe et al., 2017c). Only the silt-clay
particles were processed for metal, total organic carbon (TOC) and total nitrogen (TN)
analyses. In this study, metals were analysed in the silt-clay particles in order to minimise the
potential effect of grain size on the metal distribution (Horowitz, 1985). Prior to the analyses
of metals, TOC and TN, the silt-clay samples were homogenised using a Fritsch Pulveriser
(Botwe et al., 2017d). For the metal analysis, 2.5 ml of 65% HNO3 was added to about 0.25 g
portions of the sediment samples in Teflon tubes, placed in a stainless steel bomb, and
digested on a hot plate at 120°C for 4 h following the Canadian National Laboratory for
Environmental Testing (1994) protocol. Each digested sediment sample was quantitatively
transferred into a polypropylene tube using deionised water to obtain 50 ml final solution and
subsequently assayed for metal concentrations by Atomic Absorption Spectrometry (Varian
AA 240FS) with deuterium background correction. Mn, Pb, Cr, Cu, Zn, Ni and Fe were
analysed using the Flame Technique, Sn and As by the Graphite Furnace Technique, and Hg
by the Cold Vapour Technique. The detection limits for the analysed metals were: 0.10 mg
kg-1 dw for Hg and As; 0.50 mg kg-1 dw for Mn, Pb, Cr, Zn, Ni, Sn and Fe; and 1.0 mg kg-1
dw for Cu. The TOC and TN contents of the sediments were determined on 0.5 g of dry
sediment samples using the Walkley-Black wet oxidation and the Kjeldahl methods,
respectively, following Botwe et al. (2017c).
8.2.3. Quality control/assurance
Prior to the metal analyses, auto calibration of the AAS was made by aspirating a bulk
standard (Multi-elemental standard solution for ICP, Fluka Analytical, Switzerland).
Procedural blanks and a Certified Reference Material for marine sediments (IAEA-158) were
processed in a similar way as the field samples and analysed to check the quality of all results.
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
220
Sediment samples were analysed in duplicates while reference materials were analysed in
triplicates. Chemicals, solvents and reagents used were of trace metal analysis grade (from
Sigma-Aldrich, U.S.A). All containers were thoroughly washed with detergent, soaked in a
10% HNO3 solution overnight, rinsed with deionised water and dried in an oven prior to their
use. Sediment traps were also conditioned with dilute nitric acid and rinsed with distilled
water prior to their use. Metal recoveries were in the range of 63-95.5 %, with relative
standard deviations (RSD) of <5% (not shown).
8.2.4. Data analysis
One-way analysis of variance (ANOVA) and the Holm-Sidak multiple comparison test were
performed to assess the spatial and temporal variations in the accumulated dry mass of silt-
clay and their associated metal and TOC contents using the statistical software SigmaPlot
(version 11.0). When the normality test failed, Kruskal-Wallis one-way ANOVA on ranks
was performed instead of the Holm-Sidak multiple comparison test. Two-tailed Pearson
correlations were conducted to examine linear relationships among the measured metals,
accumulated dry mass of silt-clay and TOC concentrations using SPSS (version 16.0).
Descriptive statistics such as means, standard deviations and standard errors were computed in
Microsoft Excel 2007 at the 95% confidence level.
The settling fluxes of silt-clay (Fs), with units of g m-2
d-1
, were estimated using Eq. 1 (Botwe
et al., 2017b):
Fs = (M )/(A x D) (1)
where M is the dry accumulated mass of silt-clay (kg) in the sediment trap, A is the cross-
sectional area of the sediment trap (m2) and D is the duration of trap deployment (d).
The settling fluxes of silt-clay associated metals (Fm, with units of mg m-2
d-1
) were estimated
using Eq. 2:
Fm= Fs x Cm (2)
where Cm is the metal concentration in the silt-clay particles (mg g-1
d.w).
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
221
Metal contamination in sediments may originate from lithogenic and anthropogenic sources
(Clark, 2001). To delineate lithogenic from anthropogenic metal contamination in the Tema
Harbour sediments, metal enrichments in the sediments were assessed against average crustal
metal concentrations (Taylor, 1964) by deriving the metal enrichment factors (EFs) using Fe
as a normaliser according to Eq. (3) (Addo et al., 2011; Yilgor et al., 2012):
EF = [M/Fe]Sample/[M/Fe]Crust (3)
where [M/Fe]Sample is the metal-iron ratio in the Tema Harbour sediments and [M/Fe]Crust is
the metal-iron ratio based on the average crustal concentrations reported by Taylor (1964) as
proxies for their background concentrations in the Tema Harbour and were: Fe = 56,300; Mn
= 950; Pb = 12.5; Cr = 100; Cu = 55; Zn = 70; Ni = 75; Hg = 0.08; Sn = 2; As = 1.8 mg.kg-1
.
By this approach, the progression of metal enrichment is as follows: deficient (EF ≤ 1), minor
enrichment (1 < EF ≤ 3), moderate enrichment (3 < EF ≤ 5), moderately severe enrichment (5
< EF ≤ 10), severe enrichment (10 < EF ≤ 25), very severe enrichment (25 < EF ≤ 50), and
extremely severe enrichment (EF > 50).
Quantitative assessment of metal contamination in the Tema Harbour sediments was
conducted by deriving metal geo-accumulation indices (Igeo) (Muller, 1969), following
Botwe et al. (2017d) according to Eq. (4):
Igeo = Log2 [Cn/(1.5 x Bn)] (4)
where Cn is the metal concentration in the Tema Harbour sediment and Bn is the
corresponding average crustal concentration (Taylor, 1964) taken as a proxy for the metal
background concentration (Botwe et al., 2017b). The Igeo quantifies the progression of metal
contamination in sediments as follows (Muller, 1969): uncontaminated (Igeo < 0),
uncontaminated to moderately contaminated (0 ≤ Igeo < 1), moderately contaminated (1 ≤
Igeo < 2), moderately to highly contaminated (2 ≤ Igeo < 3), heavily contaminated (3 ≤ Igeo <
4), highly to very highly contaminated (4 ≤ Igeo < 5), very heavily contaminated (Igeo ≥ 5).
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
222
8.3. Results
8.3.1. Metals, TOC and TN concentrations in settling silt-clay particles in the Tema
Harbour
Table 8.1 presents the accumulated dry masses of sediment fractions in the sediment traps and
silt-clay associated metal, TOC and TN contents at the different sampling stations and for the
sampling periods. The accumulated sediments in the sediment traps were mainly composed of
sand with dry masses ranging from 7.8 to 412 g, representing 67-99 % of the dry bulk
sediment mass accumulated in the traps, while the dry masses of the silt-clay particles were in
the range of 1.9-38.5 g, representing 1-33 % of the dry bulk sediment mass accumulated in the
traps. The silt-clay particles contained varying concentrations of metals with Fe occurring in
relatively higher concentrations. Among the other metals, Mn (260-1083 mg.kg-1
dw) and As
(146-1470 mg.kg-1
dw) were present in relatively high concentrations. The Hg concentrations
were relatively low and ranged from <0.1 to 3.0 mg.kg-1
dw, while those of Pb, Cr, Cu, Zn, Ni
and Sn were in the ranges of 20.3-229, 22.5-373, 15.8-119, 94.6-354, 18.4-66.1 and 6.2-49.2
mg.kg-1
dw, respectively. The TOC content of the accumulated silt-clay particles ranged from
2.1 to 13.3%, while the TN content ranged from 0.42 to 0.98% with corresponding TOC/TN
ratios in the range of 3.3-27.7 (Table 8.1).
Table 8.2 presents the correlation matrix of the metal concentrations with the TOC content.
The results show a strong direct correlation between Cu and Zn concentrations (r = 0.76, p
<0.01). Both Cu and Zn exhibited statistically significant moderate correlations with Pb and
Fe. Cr exhibited statistically significant moderate correlations with Cu (r = 0.49, p <0.01) and
Sn (r = 0.45, p <0.01), but weak correlations with Fe (r = 0.37, p <0.01) and Ni (r = 0.28, p
<0.05). Hg and Sn were also correlated (r = 0.44, p <0.01), while Mn exhibited weak but
statistically significant inverse correlations with Pb (r = -0.28, p <0.05) and As (r = -0.27, p
<0.05). There were no statistically significant correlations between the TOC and the measured
metals.
Table 8.1 Accumulated sediment fractions in sediment traps deployed at different sampling stations (see Fig. 7.1) and
periods in Tema Harbour (Ghana) and the silt-clay particles associated metal, TOC and TN contents
Sediment fractions Silt-clay particles associated metal concentrations (mg kg
-1 dw)
Sampling
period
Sampling
station
Trap
position
Silt-clay
(g dw)
Sand
(g dw) Mn Pb Cr Cu Zn Ni Hg Sn As Fe
TOC
(%)
TN
(%) TOC/TN
Week 2 I Top 5.1 24.2 418 65.0 189 63.6 244 34.4 0.40 24.0 374 35740 3.6 0.64 5.6
Bottom 2.7 26.9 611 47.3 217 64.9 251 54.8 0.47 35.5 147 40840 9.6 0.62 15.5
II Top 4.1 36.7 530 55.4 187 59.7 236 23.2 0.43 22.6 192 51940 4.0 0.64 6.3
Bottom 3.1 42.6 607 75.3 210 62.5 230 27.0 0.30 22.8 226 40740 3.2 0.48 6.7
III Top 2.0 120.1 289 229 231 67.7 271 22.5 0.41 31.2 440 49240 2.4 0.64 3.8
Bottom 2.3 181.5 282 26.7 132 21.3 210 18.4 0.12 25.5 259 37440 2.3 0.52 4.4
IV Top 4.5 119.8 592 28.3 167 49.3 193 23.0 0.23 16.4 148 40590 9.2 0.42 21.9
Bottom 3.6 95.4 510 43.9 200 52.5 206 31.5 0.50 25.8 336 52840 8.4 0.58 14.5
V Top 7.2 268 770 21.0 162 50.4 195 38.6 0.42 24.2 614 56300 4.4 0.7 6.3
Bottom 2.0 214.8 1183 20.3 175 40.8 168 22.5 0.36 20.4 146 36380 9.2 0.42 21.9
Week 4 I Bottom 4.9 45.1 616 65.3 204 54.5 193 54.7 0.24 31.8 454 41770 5.0 0.50 10.0
II Top 5.2 89.6 640 54.9 184 50.3 196 54.4 0.20 21.5 403 39170 2.1 0.53 4.0
Bottom 4.7 69.1 678 36.3 32.5 38.2 187 63.7 0.30 8.5 443 37610 4.0 0.45 8.9
III Top 9.8 113.5 548 26.4 26.5 29.6 175 44.5 0.17 6.2 403 40330 3.6 0.86 4.2
Bottom 4.9 249.2 523 21.6 41.3 34.5 186 47.8 0.10 6.8 522 43230 5.2 0.5 10.4
IV Top 9.3 69.2 616 33.2 199 45.4 195 55.7 0.30 14.1 493 49880 8.0 0.81 9.9
Bottom 10.5 30.2 517 50.3 287 49.6 185 56.6 0.16 20.8 758 47710 3.6 0.47 7.7
V Top 9.9 88.0 553 41.6 61.5 38.5 188 52.1 0.26 32.9 352 38530 5.2 0.45 11.6
Bottom 3.5 76.3 709 22.6 196 43.9 189 52.8 0.30 35.6 373 43440 8.4 0.5 16.8
Week 6 I Top 4.1 11.8 538 45.6 225 65.8 208 66.1 0.42 32.3 572 63690 4.4 0.56 8.5
Bottom 4.4 19.9 563 45.5 231 57.7 198 62.7 0.27 29.8 656 54130 6.4 0.44 14.5
II Top 20.6 68.6 598 42.2 202 46.5 172 53.2 0.51 25.0 606 35860 4.0 0.47 8.5
Bottom 1.9 7.8 486 41.1 231 55.5 190 61.7 0.25 22.6 427 42690 6.2 0.58 10.7
III Top 3.6 84.2 483 34.1 204 48.5 196 37.1 0.20 35.0 508 40530 5.8 0.45 12.9
Bottom 6.2 24.3 284 49.6 146 36.5 217 39.2 0.38 24.7 480 39330 2.4 0.72 3.3
IV Top 11.0 77.9 541 44.4 172 37.0 150 42.5 1.33 39.9 539 41670 7.9 0.98 8.1
Bottom 38.5 139.6 657 31.7 195 43.4 171 47.2 3.00 47.3 612 50020 6.0 0.53 11.3
Table 8.1 continued
Sediment
fractions Silt-clay particles associated metal concentrations (mg kg
-1 dw)
Sampling
period
Sampling
Station
Trap
position
Silt-
clay
(g dw)
Sand
(g dw) Mn Pb Cr Cu Zn Ni Hg Sn As Fe
TOC
(%)
TN
(%) TOC/TN
V Top 5.7 34.2 510 50.2 236 36.3 168 53.1 0.25 34.7 683 35180 7.2 0.82 8.8
Bottom 5.8 42.4 511 41.3 212 26.1 171 39.7 0.10 49.2 491 38010 4.4 0.67 6.6
Week 8 I Bottom 3.8 33.1 402 31.8 22.5 21.9 95 22.4 0.10 22.8 378 37040 7.8 0.55 14.2
II Top 3.1 64.8 563 47.6 34.3 15.8 154 19.4 0.10 24.4 382 40460 6.4 0.58 11.0
III Top 5.4 350 422 47.6 61.0 33.9 157 26.9 0.18 24.5 551 37860 3.2 0.57 5.6
Bottom 7.7 153 406 46.6 136 43.9 164 35.4 0.23 22.2 603 39850 4.4 0.54 8.1
IV Top 7.1 184 426 51.2 215 40.4 164 27.5 0.28 24.8 278 36080 7.2 0.5 14.4
Bottom 8.6 26.9 679 31.8 179 31.9 156 31.0 0.30 27.7 244 34900 4.7 0.62 7.6
V Top 2.1 32.7 637 29.8 181 38.2 153 46.5 0.48 20.4 617 48980 7.2 0.54 13.3
Bottom 5.4 47.8 537 25.3 184 40.8 169 45.6 0.28 30.6 569 44950 4.4 0.56 7.9
Week 10 I Top 4.5 118.4 368 31.6 138 48.6 162 34.9 0.21 22.5 520 35720 4.4 0.5 8.8
Bottom 4.6 155.2 406 50.2 373 62.2 206 58.4 0.29 35.9 1137 57960 6.5 0.53 12.3
II Top 6.3 112.2 597 80.2 270 70.1 226 44.3 0.53 38.5 775 65920 5.2 0.62 8.4
Bottom 3.7 38.5 260 44.8 245 49.7 149 38.3 0.22 16.7 615 37600 4.0 0.42 9.5
III Top 5.3 111 409 47.4 200 50.9 174 35.4 0.10 23.6 342 37100 8.4 0.44 19.1
Bottom 2.7 49.7 402 32.4 210 47.7 171 36.9 0.30 23.5 399 26240 8.8 0.95 9.3
IV Top 3.6 66.8 309 48.6 173 32.4 120 27.1 0.54 20.7 628 39360 3.6 0.45 8.0
Bottom 2.3 28.7 438 41.5 233 47.6 157 44.1 0.81 28.9 573 53920 5.8 0.73 7.9
V Top 4.8 49.2 557 35.0 180 119.4 354 28.6 0.20 31.5 1051 49340 6.0 0.48 12.5
Bottom 3.8 56.1 460 44.1 232 42.4 156 39.6 0.26 33.9 591 56070 6.3 0.45 14.0
Week 12 I Bottom 8.7 72.4 358 51.1 228 64.1 212 35.6 1.12 34.4 888 34550 4.8 0.42 11.4
II Top 2.4 20.7 400 34.6 179 46.7 136 27.8 0.41 25.9 1054 38010 4.0 0.53 7.5
Bottom 7.5 28.1 434 41.3 195 50.4 186 32.2 0.71 23.6 1137 40050 6.7 0.45 14.9
III Top 5.5 11.2 294 42.0 187 45.5 144 31.3 0.44 22.3 1467 33290 7.9 0.67 11.8
Bottom 5.8 68.8 368 32.7 106 47.8 166 33.2 0.81 31.9 1470 39810 5.2 0.62 8.4
IV Top 8.2 412 469 43.4 267 55.3 177 41.4 0.21 29.0 1045 49920 4.7 0.49 9.6
Bottom 4.2 31.5 786 37.6 270 53.8 173 45.1 0.40 26.5 1161 44710 2.8 0.53 5.3
V Top 4.1 30.8 494 38.2 276 46.8 152 45.4 0.93 31.4 426 44710 13.3 0.48 27.7
Bottom 5.3 33.6 580 43.1 226 57.9 155 42.8 0.28 26.4 434 34970 13.3 0.67 19.9
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
225
Table 8.2 Correlation matrix of metal and TOC concentrations in settling silt-clay
particles in the Tema Harbour, Ghana (n = 56)
*Correlation is significant at the 0.05 level (2-tailed)
**Correlation is significant at the 0.01 level (2-tailed)
8.3.2. Distributions and fluxes of silt-clay particles associated metals in the Tema
Harbour
At all the sampling stations, t-tests revealed no significant differences (p > 0.05) between the
mean silt-clay particles associated metal concentrations in the top and bottom traps. Similarly,
the mean TOC content in the silt-clay did not differ significantly (p > 0.05) between the top
and bottom traps across the sampling stations. Therefore, the mean metal concentrations for
the top and bottom traps at each station were determined to assess the temporal and spatial
distributions of the metals, which are presented in Figs. 8.1 and 8.2, respectively. One-way
ANOVA with pairwise multiple comparison procedures (Holm-Sidak method) and Kruskal-
Wallis one way ANOVA on ranks with pairwise multiple comparison procedures (Dunn's
Method) revealed statistically significant temporal variations in the concentrations of Ni (p
<0.001), Cu (p = 0.010), Zn (p <0.001), Sn (p = 0.034) and As (p <0.001). Relatively higher
concentrations of Ni occurred in weeks 4 and 6 (Fig. 8.1f), the lowest concentrations of Cu
(Fig. 8.1d) and Zn (Fig. 8.1e) occurred in week 8, the highest concentration of Sn was
observed during week 6 (Fig. 8.1h), while the concentrations of As increased over the period
with a decrease during the eighth week (Fig. 8.1i).
Mn Pb Cr Cu Zn Ni Hg Sn As Fe
Pb -0.28*
Cr -0.01 0.23
Cu 0.04 0.30* 0.49**
Zn 0.07 0.38** 0.20 0.76**
Ni 0.23 -0.14 0.28* 0.14 0.05
Hg 0.07 -0.01 0.14 0.05 -0.06 0.07
Sn -0.01 0.16 0.45** 0.19 0.14 0.10 0.44**
As -0.27* -0.05 0.24 0.27* -0.05 0.09 0.17 0.17
Fe 0.16 0.16 0.37** 0.38** 0.32* 0.32* 0.16 0.25 0.16
TOC 0.21 -0.26 0.18 0.04 -0.19 0.05 0.12 0.12 -0.14 -0.07
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
226
0
100
200
300
400
500
600
700
2 4 6 8 10 12Me
an
Mn
co
nce
ntr
ation
(m
g.k
g-
1 d
w)
Sampling period (week)
a
0
10
20
30
40
50
60
70
80
90
2 4 6 8 10 12
Me
an
Pb
co
nce
ntr
ation
(m
g.k
g-
1 d
w)
Sampling period (week)
b
0
50
100
150
200
250
300
2 4 6 8 10 12
Me
an
Cr
co
nce
ntr
atio
n (
mg
.kg
-1
dw
)
Sampling period (week)
c
0
10
20
30
40
50
60
70
2 4 6 8 10 12
Mean C
u c
oncentr
ation (
mg.k
g-1
dw
)
Sampling period (week)
d
0
50
100
150
200
250
2 4 6 8 10 12
Me
an
Zn
co
nce
ntr
atio
n (
mg
.kg
-1
dw
)
Sampling period (week)
e
0
10
20
30
40
50
60
2 4 6 8 10 12Me
an
Ni co
nce
ntr
ation
(m
g.k
g-1
d
w)
Sampling period (week)
f
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
227
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
2 4 6 8 10 12Me
an
Hg
co
nce
ntr
ation
(m
g.k
g-
1 d
w)
Sampling period (week)
g
0
5
10
15
20
25
30
35
40
2 4 6 8 10 12
Me
an
Sn
co
nce
ntr
ation
(m
g.k
g-
1 d
w)
Sampling period (week)
h
0
200
400
600
800
1000
1200
2 4 6 8 10 12
Me
an
As c
once
ntr
ation
(m
g.k
g-
1 d
w)
Sampling period (week)
i
0
10000
20000
30000
40000
50000
60000
2 4 6 8 10 12
Me
an
Fe c
once
ntr
ation
(m
g.k
g-
1 d
w)
Sampling period (week)
j
Fig. 8.1 Temporal distribution of settling silt-clay particles associated metal
concentrations (mean ± standard error) in the Tema Harbour (Ghana): (a) Mn, (b) Pb,
(c) Cr, (d) Cu, (e) Zn, (f) Ni, (g) Hg, (h) Sn, (i) As and (j) Fe.
The spatial trends in the metal concentrations in the settling silt-clay particles in the Tema
Harbour are shown in Fig. 8.2. Among the analysed metals, Kruskal-Wallis one-way ANOVA
on ranks with pairwise multiple comparison procedures (Dunn's Method) revealed statistically
significant spatial variations in the concentrations of Mn (p = 0.003), Pb (p = 0.041) and Cu (p
= 0.032). Relatively lower concentrations of Mn (Fig. 8.2a) and Cu (Fig. 8.2d) were observed
at station III, while relatively lower concentrations of Pb were observed at station V (Fig.
8.2b).
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
228
0
10
20
30
40
50
60
70
80
I II III IV V
Me
an
Pb
co
nce
ntr
ation
(m
g.k
g-
1 d
w)
Sampling station
b
0
50
100
150
200
250
I II III IV VMe
an
Cr
co
nce
ntr
ation
(m
g.k
g-1
d
w)
Sampling station
c
0
10
20
30
40
50
60
70
I II III IV V
Me
an
Cu
co
nce
ntr
ation
(m
g.k
g-
1 d
w)
Sampling station
d
0
50
100
150
200
250
I II III IV V
Me
an
Zn c
once
ntr
ation
(m
g.k
g-
1 d
w)
Sampling station
e
0
10
20
30
40
50
60
I II III IV V
Mean N
i concentr
ation (
mg.k
g-1
dw
)
Sampling station
f
0
100
200
300
400
500
600
700
800
I II III IV VMe
an
Mn
co
nce
ntr
ation
(m
g.k
g-
1 d
w)
Sampling station
a
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
229
0100
2 4 6 8 10 12
B i w Week
0
5
10
15
20
25
30
35
I II III IV V
Me
an
Sn
co
nce
ntr
ation
(m
g.k
g-
1 d
w)
Sampling station
h
0
10000
20000
30000
40000
50000
60000
I II III IV V
Me
an
Fe c
once
ntr
ation
(m
g.k
g-
1 d
w)
Sampling station
j
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
I II III IV V
Me
an
Hg
co
nce
ntr
ation
(m
g.k
g-
1 d
w)
Sampling station
g
0
100
200
300
400
500
600
700
800
I II III IV V
Me
an
As c
once
ntr
ation
(m
g.k
g-
1 d
w)
Sampling station
i
Fig. 8.2 Spatial distribution of settling silt-clay particles associated metal
concentrations (mean ± standard error) in the Tema Harbour (Ghana): (a) Mn, (b) Pb,
(c) Cr, (d) Cu, (e) Zn, (f) Ni, (g) Hg, (h) Sn, (i) As and (j) Fe. See sampling stations A-
E in Fig. 7.1.
The estimated mean daily settling fluxes of silt-clay and associated metals at the five sampling
stations in the Tema Harbour are presented in Table 8.3. The mean daily settling fluxes of silt-
clay across the sampling stations ranged from 42.7 (± 5.1) to 85.0 (± 31) g.m-2
.d-1
, while the
mean fluxes of associated metals across the sampling stations ranged from 15.8 (± 3.9) to 49.4
(± 20.4) mg.m-2
.d-1
for Mn, 1.6 (± 0.4) to 3.3 (± 1.0) mg.m-2
.d-1
for Pb, 5.7(± 1.3) to 17.6(±
6.1) mg.m-2
.d-1
for Cr, 1.8 (± 0.6) to 3.7 (± 1.4) mg.m-2
.d-1
for Cu, 6.4 (± 1.9) to 14.9
Table 8.3 Estimated daily settling fluxes of silt-clay particles and associated metals (mean ± standard error) at different sampling
stations over a 12-week period in the Tema Harbour (Ghana)
Metal flux
Sampling
station
Silt-clay flux
(g.m-2
.d-1
) Mn* Pb* Cr* Cu* Zn* Ni* Hg** Sn* As*
aI 42.7 ± 5.1 15.8 ± 3.9 1.6 ± 0.5 6.8 ± 2.2 1.8 ± 0.6 6.4 ± 1.9 2.0 ± 0.4 14.9 ± 8.4 2.1 ± 0.3 18.5 ± 7.2
bII 50.6 ± 17.0 26.2 ± 10.2 2.4 ± 0.8 8.9 ± 3.8 2.4 ± 0.9 8.9 ± 3.1 2.0 ± 0.9 20.3 ± 10.7 1.2 ± 0.5 29.0 ± 13.4
cIII 46.3 ± 8.7 19.0 ± 4.7 2.0 ± 0.5 5.7 ± 1.3 1.9 ± 0.3 8.3 ± 1.5 1.7 ± 0.4 13.0 ± 4.5 1.0 ± 0.2 30.2 ± 10.1
cIV 85.0 ± 31.0 49.4 ± 20.4 3.3 ± 1.0 17.6 ± 6.1 3.7 ± 1.4 14.9 ± 5.8 3.0 ± 0.8 114 ± 85 2.8 ± 1.5 45.2 ± 17.8
cV 45.1 ± 7.7 26.9 ± 4.2 1.6 ± 0.4 8.2 ± 1.3 2.2 ± 0.5 8.5 ± 1.6 2.0 ± 0.5 14.5 ± 2.9 1.4 ± 0.3 24.1 ± 4.9
*Measured in mg.m
-2d
-1
**Measured in µg.m-2
d-1
; an = 9;
bn = 11;
cn = 12
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
231
(± 5.8) mg.m-2
.d-1
for Zn, 1.7 (± 0.4) to 3.0 (± 0.8) mg.m-2
.d-1
for Ni, 13.0 (± 4.5) to 114 (±
85) µg.m- 2.d
-1 for Hg, 1.0 (± 0.2) to 2.8 (± 1.5) mg.m
-2.d
-1 for Sn, and 18.5 (± 7.2) to 45.2 (±
17.8) mg.m-2
.d-1
for As. The settling fluxes of Pb, Cu, Ni and Sn were comparable, being an
order of magnitude lower than those of Mn and As, but about two orders of magnitude higher
than those of Hg. Relatively higher silt-clay and metal fluxes occurred at the more outer
station IV although no clear spatial trend was observed.
There were strong correlations between the silt-clay fluxes and the fluxes for the different
metals (r values ranging from 0.87 to 0.96, p < 0.01), while the fluxes for the different metals
investigated were also strongly correlated (r values ranging from 0.71 to 0.99, p <0.01) (Table
8.4).
Table 8.4 Correlation matrix of silt-clay particle and metal fluxes in the Tema
Harbour, Ghana (n = 56)
Silt-
clay Mn Pb Cr Cu Zn Ni Hg Sn
Mn 0.96
Pb 0.87 0.86
Cr 0.95 0.97 0.87
Cu 0.94 0.96 0.93 0.95
Zn 0.95 0.97 0.92 0.94 0.99
Ni 0.91 0.97 0.91 0.94 0.98 0.98
Hg 0.93 0.90 0.71 0.89 0.85 0.86 0.83
Sn 0.95 0.98 0.82 0.97 0.94 0.95 0.95 0.94
As 0.89 0.89 0.92 0.88 0.93 0.96 0.92 0.81 0.89
All correlations are significant at the 0.01 level (2-tailed)
8.4. Discussion
8.4.1. Metal distribution and contamination in settling silt-clay partices in the Tema
Harbour
The settling sediments in the Tema Harbour were characterised by a predominance of sand,
which may be attributed to its quicker removal from the water column than the silt-clay
particles (Eisma, 1993; Ji, 2008). The Ni, Cu, Zn, Sn, As Mn, Pb and Cu concentrations in the
silt-clay particles exhibited temporal and/or spatial variations. Generally, variations in
sediment-metal concentrations are commonly attributed to variations in silt-clay, Fe and Mn
oxides and hydroxides as well as organic matter content in sediments as these tend to
concentrate metals (Horowitz, 1985; Horowitz and Elrick, 1987; Horowitz et al., 1989;
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
232
Hamzeh et al., 2014). The analysis of the silt-clay particles might have diminished the
potential effect of TOC on sediment metal distribution, resulting in the poor correlations
between TOC and metal concentrations (Table 8.2). The statistically significant Cu/Fe, Zn/Fe,
Cr/Fe, Pb/Mn and As/Mn correlations indicate a potential influence of Fe oxides and
hydroxides on Cu, Zn and Cr distributions as well as of Mn oxides and hydroxides on Pb and
As distributions in the harbour sediments.
The calculated EFs indicated varying levels of metal enrichment in the Tema Harbour
sediments, which are summarised in Table 8.5. The harbour sediments were predominantly
characterised by severe As enrichment, moderate to severe Pb, Zn and Sn enrichments,
deficient to minor Mn, Cr, Cu and Hg enrichments, and were deficient in Ni. The EFs of As
and Sn (in 91% of the cases) were >10, indicating they were mainly derived from
anthropogenic inputs (Addo et al., 2011; Yilgor et al., 2012; Botwe et al., 2017d). For Pb, Cr,
Zn and Hg, the EFs were mostly between 1.5 and 10, indicating considerable anthropogenic
inputs of these metals in the Tema Harbour sediments. On the contrary, the low EFs (<1.5) of
Mn, Cu and Ni suggest mainly lithogenic sources of these metals in the Tema Harbour
sediments (Addo et al., 2011; Yilgor et al., 2012; Botwe et al., 2017d).
The computed Igeo values, summarised in Table 8.5, indicated that metal enrichment in the
Tema Harbour sediments had reached varying pollution levels. All the harbour sediments
were potentially very heavily polluted with As, while potentially high Sn pollution and
moderate Pb, Cr and Zn pollution occurred in the majority of the sediments (over 60%). The
sediments exhibited a predominance of moderate to very high Hg pollution, but were
potentially unpolluted with Mn and Ni. The Igeo values also indicated that Cu enrichment in
the sediments had not reached pollution levels. These results indicate considerable
anthropogenic inputs of As, Sn, Hg, Pb, Zn and Cr as compared to Mn, Cu and Ni in the Tema
Harbour, which agrees well with findings from a previous study on bottom sediments in the
harbour (Botwe et al., 2017d).
Anthropogenic metal inputs into the Tema Harbour may derive principally from shipping and
fishing activities such as sand blasting, scraping and painting of ships, bunkering, bilge
discharges, debalasting, refueling and associated oil spills (Lepland et al., 2010; Mestres et al.,
2010; Nyarko et al., 2014; Botwe et al., 2017a, 2017d) as well as metal-containing wastewater
and particulates discharged from oil refinery, cement production, ore smelting, automobile
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
233
Table 8.5 Metal enrichment and pollution levels and their incidence of occurrence in
settling silt-clay particles in Tema Harbour (Ghana)
Metal enrichment levels and contamination status were based on their enrichment factors
(EFs) and geo-accumulation indices (Igeo), respectively. For interpretation of the EF and Igeo
values, see Section 8.2.4.
exhaust and agrochemical use within the harbour area (Yilgor et al., 2012; El-Sorogy et al.,
2016; Botwe et al., 2017c). The occurrence of Sn contamination in harbour sediments is
mainly attributable to the use of tributyltin (TBT)-based anti-fouling paints on ships, boats
and docks (Berto et al., 2007; Nyarko et al. 2011; Castro et al. 2012; Botwe et al., 2017d). In
2001, the International Maritime Organisation (IMO) adopted the International Convention on
the Control of Harmful Anti-fouling Systems on Ships, which calls on states to take steps
toward the reduction of organotin pollution due to the ecological risks posed by TBT to the
marine environment and human health. Since then, TBT use has been restricted in many
countries (Berto et al., 2007), but could remain in use in developing countries like Ghana.
Thus, the presence of Sn in the Tema Harbour sediments may derive from current use of TBT-
based anti-fouling paints in the Tema Harbour or residual/secondary contaminant sources
Enrichment level Incidence of occurrence for measured metals (%, n = 56)
Mn Pb Cr Cu Zn Ni Hg Sn As
No enrichment 94.6 0 12.5 39.3 0 100 39.3 1.8 0
Minor enrichment 5.4 16.1 62.5 60.7 28.6 0 30.4 0.0 0
Moderate enrichment 0 46.4 25.0 0 66.1 0 26.8 73.2 0
Moderate to severe enrichment 0 35.7 0 0 5.4 0 1.8 25.0 0
Severe enrichment 0 1.8 0 0 0 0 1.8 0 100
Very severe enrichment 0 0 0 0 0 0 0 0 0
Extremely severe enrichment 0 0 0 0 0 0 0 0 0
Contamination status Incidence of occurrence for measured metals (%, n = 56)
Mn Pb Cr Cu Zn Ni Hg Sn As
Uncontaminated 100 16.1 25.0 100 1.8 100 8.9 0 0
Uncontaminated to moderately
contaminated 0 75.0 75.0 0 76.8 0 19.6 0 0
Moderately contaminated 0 7.1 0 0 21.4 0 48.2 5.4 0
Moderately to highly
contaminated 0 1.8 0 0 0 0 16.1 26.8 0
Heavily contaminated 0 0 0 0 0 0 5.4 64.2 0
Highly to very highly
contaminated 0 0 0 0 0 0 1.8 3.6 0
Very heavily contaminated 0 0 0 0 0 0 0 0 100
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
234
since TBT is persistent in the environment (Berto et al., 2007) and, therefore, its attenuation
and recovery in sediments may be a slow process. Arsenic (As) is hazardous (Casado-
Martínez et al., 2006; Affum et al., 2016; Botwe et al., 2017d) and a Class A human
carcinogen (Chen, 2001) and therefore, its "heavy" contamination in the Tema Harbour
sediments is of considerable concern. The increasing temporal trend of As concentrations
(Fig. 8.1i) points to the existence of continuous sources of As at the harbour, which may be
linked to metal smelting activities and the use of As-containing agrochemicals in Tema (El-
Sorogy et al., 2016).
Significant correlations among metals in sediments have commonly been attributed to similar
sources of the metals (Qu and Kelderman, 2001; Ramirez et al., 2005; Nyarko et al., 2011;
Nyarko et al., 2014; Affum et al., 2016; Botwe et al., 2017d). Since the EF and Igeo values
indicate Ni and Cu in the Tema Harbour sediments derived mainly from lithogenic origin,
other factors such as similar accumulation patterns of the metals in sediments could also
explain the observed Cu/Zn, Cu/Pb, Cu/Cr, Zn/Pb, Cr/Sn, Cr/Ni and Sn/Hg correlations in the
harbour sediments (Aloupi and Angelidis, 2001). Thus, it is important to exercise caution in
the use of EFs and Igeo as interpretative tools for the assessment of metal sources and
contamination, especially when average crustal metal concentrations are used as proxies for
background metal concentrations.
Despite potential differences in grain size distribution, geology and methodologies, we
compared the Sn and As concentrations in the Tema Harbour sediments with concentrations
found in other coastal sediments worldwide (Table 8.6). The As concentrations in the Tema
Harbour sediments were high compared to values reported for gold mining areas in Ghana
(Affum et al., 2016) and coastal sediments from Egypt (Mostafa et al., 2004; Abdel Ghani et
al., 2013), Finland (Vallius et al., 2007), China (Luo et al., 2010), Spain (Díaz-de Alba et al.,
2011), Tanzania (Rumisha et al., 2012), the French Mediterranean (Mamindy-Pajany et al.,
2013), and Saudi Arabia (Al-Taani et al., 2014; Youssef et al., 2015; El-Sorogy et al., 2016).
The concentrations of Sn in the Tema Harbour sediments were low compared to values
reported for coastal sediments from Spain (Arambarri et al., 2003) and some parts of Egypt
(Abdel Ghani et al., 2013), but high compared to other parts of Egypt (El-Moselhy and
Hamed, 2000; Mostafa et al., 2004; Hamed et al., 2013) and China (Liu et al., 2011).
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
235
Table 8.6 Comparison of Sn and As concentrations in the Tema Harbour fine
sediments investigated with concentrations in other coastal sediments
worldwide (mg kg-1 dw)
8.4.2. Settling fluxes of silt-clay particles and associated metals in the Tema Harbour
The fluxes of silt-clay particles and metals in the Tema Harbour were characterised by large
local fluctuations, which may be attributed to localised metal inputs and complex dynamics of
sediments under the prevailing conditions in the Tema Harbour (Botwe et al., 2017b, e). In the
Tema Harbour, the shear bottom stress associated with the maximum tidal currents exceeds
the threshold value for resuspension of clays and fine silts (Botwe et al., 2017b) and thus, tidal
and wave actions are bound to cause resuspension and redistribution of (metal-contaminated)
sediments following deposition. Moreover, anthropogenic disturbances such as the movement
of vessels may induce sediment resuspension with subsequent redistribution in the harbour
(Lepland et al., 2010; Green and Coco, 2014). Since sediment traps integrate sediment settling
and resuspension (Botwe et al., 2017b), the sediment trap-derived fluxes represent the gross
Sediment location Sn As Reference
Tema Harbour (Ghana) 6.2-49.2 146-1470 This study
Gipuzkoa Estuary (Spain) 11-113 - Arambarri et al., 2003
Abu-Qir Bay and Eastern Harbour
(Alexandria, Egypt)
3.4-355
1.6-16.2
Abdel Ghani et al., 2013
Red Sea coast (Egypt) 0.02-1.2 - El-Moselhy and Hamed, 2000
Western Harbour (Alexandria,
Egypt) 2.1-15.3 4.7-15 Mostafa et al., 2004
Pearl River Estuary (China) 1.7-8 - Liu et al., 2011
Mediterranean coast (Egypt) 0.42-3.8 - Hamed et al., 2013
Bonsa River (Ghana) - 0.35-1.09 Affum et al., 2016
Gulf of Finland - 7.3-19.1 Vallius et al., 2007
Northern Bohai and Yellow Seas
(China) - 5.6-13 Luo et al., 2010
Algeciras Bay (Spain) - 8-23 Díaz-de Alba et al., 2011
Salaam coast (Tanzania) - 0.2-1.3 Rumisha et al., 2012
French Mediterranean marinas - 17-350 Mamindy-Pajany et al., 2013
Gulf of Aqaba (Saudi Arabia) - 12.2-15.1 Al-Taani et al., 2014
Arabian Gulf (Saudi Arabia) - 148 Youssef et al., 2015
Tarut Island (Arabian Gulf, Saudi
Arabia) - 53-342 El-Sorogy et al., 2016
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
236
downward fluxes (depositional rates) of silt-clay and associated contaminants from the water
column into bottom sediments.
Although there were no clear spatial trends in the fluxes of the silt-clay particles and
associated metals, relatively higher fluxes occurred at station IV. This is possibly a direct
result of the high tidal current at the entrance of the Main Harbour, which has the potential to
cause influxes and remobilisation of large amounts of sediment compared with the inner
stations where the tidal currents are lower (Botwe et al., 2017b). Considering that station V is
closer to the harbour entrance but recorded lower particle fluxes than station IV, it is also
possible that the tidal currents begin to lose a significant amount of energy around station IV
upon entry into the harbour. Strong direct correlations were observed among the silt-clay
particles and metal fluxes indicating that metal transport to depth and its distribution in the
Tema Harbour are well-regulated by settling of the silt-clay particles, which can be attributed
to strong metal-silt-clay interactions in the water column (Horowitz and Elrick, 1987;
Horowitz et al., 1989; Hostache et al., 2014). Thus, high settling fluxes of silt-clay in the
harbour may result in substantial fluxes of metals into the bottom sediments, a situation that
can have adverse ecological effects such as contaminant uptake by benthic organisms, reduced
light availability, loss of spawning areas, and smothering of benthic eggs and larvae (Green
and Coco, 2014).
8.4.3. Ecotoxicological risks of metal contamination in settling silt-clay particles in the
Tema Harbour
Contaminated silt-clay particles represents an important pathway of contaminant exposure to
the aquatic food chain as it can be easily ingested by benthic organisms (Bat and Raffaelli,
1998; Bat, 2005; Botwe et al., 2017a). A pair of empirically derived numerical sediment
quality guidelines (SQGs), namely the effects-range low (ERL) and effects-range median
(ERM) (Long et al., 1995; Long et al., 1998) were used to evaluate the potential
ecotoxicological risks associated with metal contamination in the settling silt-clay particles in
the Tema Harbour (Botwe et al., 2017a). Metal concentrations < ERL may cause rare
occurrence of adverse biological effects and thus pose low potential ecotoxicological risk,
concentrations > ERM may cause frequent occurrence of adverse biological effects and thus
pose high potential ecotoxicological risk, whereas concentrations in the ERL-ERM range may
cause infrequent occurrence of adverse biological effects and thus pose medium potential
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
237
ecotoxicological risk (Long et al., 1995; Long et al., 1998). Table 8.7 shows that As
concentrations in all the analysed sediments may pose high ecotoxicological risk, while the
concentrations of Cr, Cu, Zn, Ni and Hg may mainly pose medium risk. On the contrary, the
sediment Pb concentrations may be mainly associated with low ecotoxicological risk. SQGs
for Mn and Sn are not available and therefore, their associated ecotoxicological risks cannot
be evaluated using the ERL/ERM approach. Thus, although the settling fluxes of the silt-clay
particles were low, they are potentially hazardous due to the high concentrations of the
associated metals, particularly As and Sn, for which appropriate (bio)remediation strategies
need to be developed.
Table 8.7 Comparison of metal concentrations in the settling silt-clay particles at
Tema Harbour (Ghana) with effects-range low (ERL) and effects-range
median (ERM) sediment quality guideline (SQG) values
aLong et al. (1995); NA = not available
8.5. Conclusions
Settling fluxes of the silt-clay particles and their associated metals (Mn, Pb, Cr, Cu, Zn, Ni,
Hg, Sn and As) in the Tema Harbour have been investigated. The mean daily fluxes ranged
from 42.7 to 85.0 g m-2
d-1
for the silt-clay particles and from 15.8-49.4, 1.6-3.3, 5.7-17.6,
1.8-3.7, 6.4-14.9, 1.7-3.0, (1.3-11.4) x10-2
, 1.0-2.8, 18.5-45.2 mg m-2
d-1
for Mn, Pb, Cr, Cu,
Zn, Ni, Hg, Sn and As, respectively. The silt-clay fluxes and metal fluxes were characterised
by large local fluctuations possibly due to localised inputs and complex sediment dynamics in
the harbour. The silt-clay fluxes and metal fluxes showed strong correlations, indicating the
important role of the silt-clay particles in metal transport and distribution in the harbour.
Comparison with SQGs show that the concentrations of most metals in the settling silt-clay
particles are potentially toxic to benthic species and pose high ecotoxicological risks, with As
posing the greatest risk. Geochemical indices revealed different extents of metal
contamination in the harbour sediments, being most polluted with As and least polluted with
SQG SQG value (mg kg
-1 dw)
Mn Pb Cr Cu Zn Ni Hg Sn As aERL NA 46.7 81 34 150 20.9 0.15 NA 8.2
aERM NA 218 370 270 410 51.6 0.71 NA 70
% samples below ERL - 68 12 14 7 4 11 - 0
% samples within ERL-ERM
range - 30 86 86 93 71 77 - 0
% samples exceeding ERM - 2 2 0 0 25 12 - 100
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
238
Mn, Cu and Ni. The As concentrations showed an increasing temporal trend, indicating the
existence of continuous sources of As at the Tema Harbour, likely linked to metal smelting
and the use of As-containing agrochemicals in the area. This study shows that the Tema
Harbour is increasingly being impacted by anthropogenic activities. The concentrations of As
and Sn are of concern, which calls for increased efforts to address the contamination problem.
References
Abdel Ghani, S., El Zokm, G., Shobier, A., Othman, T., & Shreadah, M. (2013). Metal
pollution in surface sediments of Abu-Qir Bay and Eastern Harbour of Alexandria,
Egypt. The Egyptian Journal of Aquatic Research, 39(1), 1-12.
Addo, M.A., Okley, G., Affum, H., Acquah, S., Gbadago, J., Senu, J., & Botwe, B.O. (2011).
Water quality and level of some heavy metals in water and sediments of Kpeshie
Lagoon, La-Accra, Ghana. Research Journal of Environmental and Earth Sciences,
3(5), 487-497.
Affum, A.O., Osae Dede, S., Nyarko, B.J.B, Acquaah, S., Kwaansa-Ansah, E.E, Darko, G.,
Dickson, A., Affum, E., & Fianko, J.R. (2016). Influence of small-scale gold mining
and toxic element concentrations in Bonsa river, Ghana: A potential risk to water
quality and public health. Environmental Earth Sciences, 75, 178-194.
Al-Taani, A.A., Batayneh, A., Nazzal, Y., Ghrefat, H., Elawadi, E., & Zaman, H. (2014).
Status of trace metals in surface seawater of the Gulf of Aqaba, Saudi Arabia. Marine
Pollution Bulletin, 86(1), 582-590.
Arambarri, I., Garcia, R., & Millán, E. (2003). Assessment of tin and butyltin species in
estuarine superficial sediments from Gipuzkoa, Spain. Chemosphere, 51(8), 643-649.
Bat, L. (2005). A review of sediment toxicity bioassays using the amphipods and polychaetes.
Turkish Journal of Fisheries and Aquatic Sciences, 5(2), 119-139.
Bat, L., & Raffaelli, D. (1998). Sediment toxicity testing: a bioassay approach using the
amphipod Corophium volutator and the polychaete Arenicola marina. Journal of
Experimental Marine Biology and Ecology, 226(2), 217-239.
Berto, D., Giani, M., Boscolo, R., Covelli, S., Giovanardi, O., Massironi, M., & Grassia, L.
(2007). Organotins (TBT and DBT) in water, sediments, and gastropods of the
southern Venice lagoon (Italy). Marine Pollution Bulletin, 55(10), 425-435.
Bloesch, J., & Burns, N. (1980). A critical review of sedimentation trap technique.
Schweizerische Zeitschrift für Hydrologie, 42(1), 15-55.
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
239
Botwe, B.O., De Schamphelaere, K., Schipper, C.A., Teuchies, J., Blust, R., Nyarko, E., &
Lens, P.N.L. (2017a). Integrated hazard, risk and impact assessment of tropical marine
sediments from Tema Harbour (Ghana). Chemosphere, 177, 24-34.
Botwe, B.O., Abril, J.M., Schirone, A., Barsanti, M., Delbono, I., Delfanti, R., Nyarko, E., &
Lens, P.N.L. (2017b). Settling fluxes and sediment accumulation rates by the
combined use of sediment traps and sediment cores in Tema Harbour (Ghana). Science
of the Total Environment, 609, 1114-1125.
Botwe, B.O., Kelderman, P., Nyarko, E., & Lens, P.N.L. (2017c). Assessment of DDT, HCH
and PAH contamination and associated ecotoxicological risks in surface sediments of
coastal Tema Harbour (Ghana). Marine Pollution Bulletin, 115(1–2), 480-488.
Botwe, B.O., Alfonso, L., Nyarko, E., & Lens, P.N.L. (2017d). Metal distribution and
fractionation in surface sediments of coastal Tema Harbour (Ghana) and its ecological
implications. Environmental Earth Sciences, 76(15), 514-530
Botwe, B.O., Schirone, A., Delbono, I., Barsanti, M., Delfanti, R., Kelderman, P., Nyarko, E.,
& Lens, P.N.L. (2017e). Radioactivity concentrations and their radiological
significance in sediments of the Tema Harbour (Greater Accra, Ghana). Journal of
Radiation Research and Applied Sciences, 10(1), 63-71.
Buesseler, K.O., Antia, A.N., Chen, M., Fowler, S.W., Gardner, W.D., Gustafsson, O.,
Harada, K., Michaels, A.F., Rutgers van der Loeff, M., & Sarin, M. (2007). An
assessment of the use of sediment traps for estimating upper ocean particle fluxes.
Journal of Marine Research, 65(3), 345-416.
Canadian National Laboratory for Environmental Testing (1994). Manual of analytical
methods. Trace Metals, 2:1-14
Casado-Martínez, M.C., Buceta, J.L., Belzunce, M.J., & DelValls, T.A. (2006). Using
sediment quality guidelines for dredged material management in commercial ports
from Spain. Environment International, 32(3), 388-396.
Castro, Í.B., Arroyo, M.F., Costa, P.G., & Fillmann, G. (2012). Butyltin compounds and
imposex levels in Ecuador. Archives of Environmental Contamination and Toxicology,
62(1), 68-77.
Chen, M., Ma, L.Q., Hoogeweg, C.G., & Harris, W.G. (2001). Arsenic background
concentrations in Florida, U.S.A. surface soils: Determination and interpretation.
Environmental Forensics, 2(2), 117-126.
Clark, R.B. (2001). Marine Pollution. Oxford: Oxford University Press.
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
240
de Vicente, I., Cruz-Pizarro, L., & Rueda, F.J. (2010). Sediment resuspension in two adjacent
shallow coastal lakes: controlling factors and consequences on phosphate dynamics.
Aquatic Sciences, 72(1), 21-31.
Díaz-de Alba, M., Galindo-Riaño, M.D., Casanueva-Marenco, M.J., García-Vargas, M., &
Kosore, C.M. (2011). Assessment of the metal pollution, potential toxicity and
speciation of sediment from Algeciras Bay (South of Spain) using chemometric tools.
Journal of Hazardous Materials, 190(1), 177-187.
Eisma, D. (1993). Suspended Matter in the Aquatic Environment. Springer-Verlag.
El-Moselhy, K., & A. Hamed, M. (2000). Pollution by mercury and tin in water and sediments
of the Red Sea coasts, Egypt. Journal of Environmental Sciences, 19, 29-41.
El-Sorogy, A.S., Youssef, M., Al-Kahtany, K., & Al-Otaiby, N. (2016). Assessment of arsenic
in coastal sediments, seawaters and molluscs in the Tarut Island, Arabian Gulf, Saudi
Arabia. Journal of African Earth Sciences, 113, 65-72.
Green, M.O., & Coco, G. (2014). Review of wave‐driven sediment resuspension and transport
in estuaries. Reviews of Geophysics, 52(1), 77-117.
Hakanson, L. (2006). Suspended Particulate Matter in lakes, rivers, and marine systems.
Blackburn Press, Caldwell.
Hakanson, L., & Jansson, M. (1983) Principles of lake sedimentology. Springer Verlag,
Berlin.
Hamed, M.A., Mohamedein, L. I., El-Sawy, M.A., & El-Moselhy, K.M. (2013). Mercury and
tin contents in water and sediments along the Mediterranean shoreline of Egypt. The
Egyptian Journal of Aquatic Research, 39(2), 75-81.
Hamzeh, M., Ouddane, B., Daye, M., & Halwani, J. (2014). Trace metal mobilization from
surficial sediments of the Seine River estuary. Water, Air, & Soil Pollution, 225(3),
1878-1892.
Helali, M.A., Zaaboub, N., Oueslati, W., Added, A., & Aleya, L. (2016). Suspended
particulate matter fluxes along with their associated metals, organic matter and
carbonates in a coastal Mediterranean area affected by mining activities. Marine
Pollution Bulletin, 104(1), 171-181.
Horowitz, A.J. (1985). A primer on trace metal-sediment chemistry, U.S. Geological Survey
Water-Supply Paper 2277, 67 p.
Horowitz, A.J., & Elrick, K.A. (1987). The relation of stream sediment surface area, grain size
and composition to trace element chemistry. Applied Geochemistry, 2(4), 437-451.
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
241
Horowitz, A.J., Elrick, K.A., & Hooper, R.P. (1989). The prediction of aquatic sediment‐
associated trace element concentrations using selected geochemical factors.
Hydrological Processes, 3(4), 347-364.
Hostache, R., Hissler, C., Matgen, P., Guignard, C., & Bates, P. (2014). Modelling suspended-
sediment propagation and related heavy metal contamination in floodplains: a
parameter sensitivity analysis. Hydrology & Earth System Sciences, 18(9), 3539-3551.
Ji, Z.G. (2008). Hydrodynamics and Water Quality: Modelling Rivers, Lakes and Estuaries.
Wiley.
Kelderman, P., Ang‘weya, R., De Rozari, P., Vijverberg, T. (2012). Sediment
characteristics and wind-induced sediment dynamics in shallow Lake Markermeer, the
Netherlands. Aquatic Sciences, 74(2), 301-313.
Lepland, A., Andersen, T.J., Lepland, A., Arp, H.P.H., Alve, E., Breedveld, G.D., & Rindby,
A. (2010). Sedimentation and chronology of heavy metal pollution in Oslo harbor,
Norway. Marine Pollution Bulletin, 60(9), 1512-1522.
Liu, B., Hu, K., Jiang, Z., Yang, J., Luo, X., & Liu, A. (2011). Distribution and enrichment of
heavy metals in a sediment core from the Pearl River Estuary. Environmental Earth
Eciences, 62(2), 265-275.
Liu, J., Clift, P.D., Yan, W., Chen, Z., Chen, H., Xiang, R., & Wang, D. (2014). Modern
transport and deposition of settling particles in the northern South China Sea:
Sediment trap evidence adjacent to Xisha Trough. Deep Sea Research Part I:
Oceanographic Research Papers, 93, 145-155.
Long, E.R., Field, L.J., & MacDonald, D.D. (1998). Predicting toxicity in marine sediments
with numerical sediment quality guidelines. Environmental Toxicology and Chemistry,
17(4), 714-727.
Long, E.R., MacDonald, D.D., Smith, S. L., & Calder, F.D. (1995). Incidence of adverse
biological effects within ranges of chemical concentrations in marine and estuarine
sediments. Environmental Management, 19(1), 81-97.
Luo, W., Lu, Y., Wang, T., Hu, W., Jiao, W., Naile, J.E., Khim, J.S., & Giesy, J.P. (2010).
Ecological risk assessment of arsenic and metals in sediments of coastal areas of
northern Bohai and Yellow Seas, China. Ambio, 39(5-6), 367-375.
Mamindy-Pajany, Y., Bataillard, P., Séby, F., Crouzet, C., Moulin, A., Guezennec, A.-G.,
Hrel, C., Marmier, N., & Battaglia-Brunet, F. (2013). Arsenic in Marina Sediments
from the Mediterranean Coast: Speciation in the Solid Phase and Occurrence of
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
242
Thioarsenates. Soil and Sediment Contamination: An International Journal, 22(8),
984-1002.
Mestres, M., Sierra, J., Mösso, C., & Sánchez-Arcilla, A. (2010). Sources of contamination
and modelled pollutant trajectories in a Mediterranean harbour (Tarragona, Spain).
Marine Pollution Bulletin, 60(6), 898-907.
Mostafa, A.R., Barakat, A.O., Qian, Y., Wade, T.L., & Yuan, D. (2004). An overview of
metal pollution in the Western Harbour of Alexandria, Egypt. Soil and Sediment
Contamination: An International Journal, 13(3), 299-311.
Muller, G., 1969. Index of geo-accumulation in sediments of the Rhine River. Journal of
Geology, 2(3): 108–118.
Nyarko, E., Botwe, B.O., Lamptey, E., Nuotuo, O., Foli, B.A., & Addo, M.A. (2011). Toxic
metal concentrations in deep-sea sediments from the jubilee oil field and surrounding
areas off the western coast of Ghana. Tropical Environmental Research, 9, 584-595.
Nyarko, E., Fletcher, A., Addo, S., Foli, B.A.K., & Mahu, E. (2014). Geochemical assessment
of heavy metals in surface sediments: a case study of the Tema Port, Ghana. Journal of
Shipping & Ocean Engineering, 4, 79-92.
Petrosillo, I., Valente, D., Zaccarelli, N., & Zurlini, G. (2009). Managing tourist harbors: Are
managers aware of the real environmental risks? Marine Pollution Bulletin, 58(10),
1454-1461.
Pozza, M.R., Boyce, J.I., & Morris, W.A. (2004). Lake-based magnetic mapping of
contaminated sediment distribution, Hamilton Harbour, Lake Ontario, Canada.
Journal of Applied Geophysics, 57(1), 23-41.
Qu, W., & Kelderman, P. (2001). Heavy metal contents in the Delft canal sediments and
suspended solids of the River Rhine: multivariate analysis for source tracing.
Chemosphere, 45(6–7), 919-925.
Ramirez, M., Massolo, S., Frache, R., & Correa, J.A. (2005). Metal speciation and
environmental impact on sandy beaches due to El Salvador copper mine, Chile.
Marine Pollution Bulletin, 50(1), 62-72.
Rumisha, C., Elskens, M., Leermakers, M., & Kochzius, M. (2012). Trace metal pollution and
its influence on the community structure of soft bottom molluscs in intertidal areas of
the Dar es Salaam coast, Tanzania. Marine Pollution Bulletin, 64(3), 521-531.
Santos-Echeandía, J., Prego, R., Cobelo-García, A., & Caetano, M. (2012). Metal composition
and fluxes of sinking particles and post-depositional transformation in a ria coastal
system (NW Iberian Peninsula). Marine Chemistry, 134, 36-46.
Settling Fluxes and Ecotoxicological Risk Assessment of Fine Sedimentary Metals in Tema Harbour (Ghana)
243
Schipper, C., Rietjens, I., Burgess, R., & Murk, A. (2010). Application of bioassays in
toxicological hazard, risk and impact assessments of dredged sediments. Marine
Pollution Bulletin, 60(11), 2026-2042.
Szmytkiewicz, A., & Zalewska, T. (2014). Sediment deposition and accumulation rates
determined by sediment trap and 210
Pb isotope methods in the Outer Puck Bay (Baltic
Sea). Oceanologia, 56(1), 85-106.
Taylor, S. (1964). Abundance of chemical elements in the continental crust: a new table.
Geochimica et Cosmochimica Acta, 28(8), 1273-1285.
Vallius, H., Ryabchuk, D., Kotilainen, A. (2007). Distribution of heavy metals and arsenic in
soft surface sediments of the coastal area off Kotka, northeastern Gulf of Finland,
Baltic Sea. In: Vallius, H. (Ed.), Holocene Sedimentary Environment and Sediment
Geochemistry of the Eastern Gulf of Finland, Baltic Sea, Geological Survey, Finland,
45:33-48.
Wang, X.-C., Zhang, Y.-X., & Chen, R.F. (2001). Distribution and partitioning of polycyclic
aromatic hydrocarbons (PAHs) in different size fractions in sediments from Boston
Harbor, United States. Marine Pollution Bulletin, 42(11), 1139-1149.
Yilgor, S., Kucuksezgin, F., & Ozel, E. (2012). Assessment of metal concentrations in
sediments from Lake Bafa (Western Anatolia): an index analysis approach. Bulletin of
Environmental Contamination and Toxicology, 89(3), 512-518.
Youssef, M., El-Sorogy, A., Al Kahtany, K., & Al Otiaby, N. (2015). Environmental
assessment of coastal surface sediments at Tarut Island, Arabian Gulf (Saudi Arabia).
Marine Pollution Bulletin, 96(1), 424-433.
General discussion and conclusions
246
9.1. Sediment pollution and accumulation in habours
Sediment pollution is a global issue that threatens environmental sustainability and human
health. Coastal marine environments, particularly harbours, are potential hot-spots of sediment
pollution, as they are bound to receive considerable amounts of chemical contaminants from
intense maritime and other anthropogenic activities such as industrialisation, agriculture and
urbanisation (Smith et al., 2009; Petrosillo et al., 2009; Lepland et al., 2010; Mestres et al.,
2010; Schipper et al., 2010; Romero et al., 2014). Moreover, water exchanges within coastal
harbours can result in the influx of large amounts of suspended sediments, which settle and
accumulate within harbour basins under low hydrodynamic conditions (Lepland et al., 2010;
Luo et al., 2010; Mestres et al., 2010). These sediments may derive from varied sources, but
are mainly supplied by riverine discharges. Globally, the discharge of sediments by rivers is
estimated at 2.3 billion tonnes per year (Syvitski et al., 2005). In Ghana, rivers discharge
about 2.4 million tonnes of sediment per year into the sea (Akrasi, 2011). Since sediments
play an important role in the fate of chemical pollutants in aquatic systems (Mulligan et al.,
2001; Ruiz-Fernandez et al 2009; Prato et al., 2011; Jiang et al., 2013), the accumulation of
sediments in harbour basins can result in the accumulation of chemical pollutants.
Considering the important role harbours play in the socio-economic development of human
societies, sediment pollution, along with high sediment accumulation rates (SARs) in harbours
imposes remedial measures, often dredging, to ensure harbour sustainability. Annually,
several millions of tonnes of sediments are dredged from harbours around the world at huge
cost and subsequently disposed of at sea (Witt et al., 2004; Bolam et al., 2006; Schipper et al.,
2010). Alternatively, dredged materials may be disposed of on land for agriculture, landfill,
beach nourishment and restoration of wetlands (Choueri et al., 2009). Apart from the high cost
of dredging, the potential of dredged materials to cause detrimental effects on receiving
ecosystems has been recognised (Hong et al., 1995; Burton, 2002; Caille et al., 2003;
Stronkhorst and van Hattum, 2003; Casado-Martinez et al., 2006; Birch and Hutson, 2009;
Choueri et al 2009; Schipper et al., 2010).
Global concerns about the potential adverse impact of dredged sediments from harbours and
their subsequent disposal on the marine environment has led to the establishment of
international treatises such as the London Convention (1972) and the London Protocol (1996),
which impose rigorous assessment of dredged materials in order to minimise their adverse
impacts. Thus, chemical pollution and sediment accumulation rates in harbours are of wide
General discussion and conclusions
247
interest to harbour engineers and managers. Many developed countries including The
Netherlands, United States, Canada, Australia, New Zealand and Spain have therefore
established regulatory standards for dredged materials based on potentially hazardous
concentrations of chemical pollutants to guide the management of dredged material (Burton,
2002; Casado-Martinez et al., 2006; Birch and Hutson, 2009; Kelderman et al., 2012). These
standards may be referred to as Sediment Quality Guidelines (SQGs) or Action Levels (ALs)
in different countries of origin, and they are used in ecotoxicological risk assessment for
evaluating the likelihood of a sediment contaminant to elicit adverse biological effects.
In Ghana, no national regulatory standards have been developed to guide the management of
dredged materials. In this thesis, a pair of SQGs namely the effects-range low (ERL) and the
effects-range median (ERM) (Long et al., 1995) were used to predict the likelihood of
ecotoxicological effect due to the measured sediment contaminants. Although the ERL and
ERM have been found to have good predictive ability (Long et al., 1995; Long et al., 1998), it
is worthy to note that SQGs have several limitations, and have been found to result in false
positive and false negative predictions in some instances (Burton, 2002). Moreover, SQGs are
chemical specific and do not establish causality where mixtures of chemicals are present
(Burton, 2002). Nonetheless, they are useful for identifying contaminants of potential concern
(Burton, 2002; Long et al., 2006; Birch and Hutson 2009) and should be used in a ―screening-
level‖ manner or ―weight-of-evidence‖ approach (Burton, 2002).
9.1.1. Chemical pollution assessment of Tema Harbour sediments
In this thesis, a ―weight-of-evidence‖ approach was adopted to pollution assessment of the
Tema Harbour sediments. A screening-level assessment was first conducted to provide a first
line of evidence of chemical pollution in the harbour sediments, characterise the potential
sources of the pollutants and identify those of potential concern (Burton, 2002; Long et al.,
2006). Based on the results from the screening-level assessment, bioassays were conducted as
a further line of evidence of chemical pollution of the Tema Harbour sediments.
9.1.1.1. Screening-level assessment of chemical pollution in the Tema Harbour
sediments
Radiological hazard indices (Chapter 3), SQGs (Chapters 4 and 5), total toxicity equivalence
(Chapter 4) and risk assessment code (Chapter 5) were used as screening tools for the
General discussion and conclusions
248
assessment of chemical pollution in the Tema Harbour sediments. This screening-level
assessment classified the Tema Harbour sediments as potentially toxic due to DDTs, HCHs
and PAHs (Chapter 4), As, Cd, Hg and Zn (Chapter 5) contamination. γ-HCH and Hg were
identified as contaminants of potential concern in Chapters 4 and 5, respectively. This first
line of evidence necessitated a more refined assessment (Burton, 2002; Long et al., 2006),
which will be discussed shortly.
To assess anthropogenic influences on harbours, many researchers have analysed the deep and
surficial layers of sediment cores (Birch and Olmos, 2008; Abrahim and Parker, 2008; Yilgor
et al., 2012). The deep layers of sediment cores represent materials deposited before the
construction of the harbour and may thus reveal the pre-impacted environmental conditions
for the harbour area. The surficial layers of sediment cores, on the other hand, represent those
that were deposited after the construction of the harbour and occur closer to the sediment-
water interface. Therefore, contaminant levels in the deep sediment layers of sediment cores
can be used to establish background levels for the harbour area, against which the levels in the
surficial sediments can be compared to assess the extent of contamination. This approach is
ideal considering that background levels of chemical contaminants may vary regionally due to
potential differences in geological properties (Jiang et al., 2013).
Chapter 7 showed that the lengths of sediment cores collected from the Tema Harbour were
too short and only captured the past 13-24 years of sedimentation. Considering that the
harbour has been in existence for over fifty years, the sediment cores could not be used to
establish contaminant background levels in the Tema Harbour. Moreover, no consistent
sediment contamination monitoring data have been collected for the harbour over the years.
Therefore, for the assessment of metal contamination levels and sources in the Tema Harbour
(Chapters 5 and 8), two widely used quantitative geochemical indices, namely the metal
enrichment factor (EF) proposed by Sinex and Helz (1981) and the geo-accumulation index
(Igeo) proposed by Muller (1969) were applied. These geochemical indices were used to
characterise the extent of metal enrichment/contamination and apportion their sources as
natural or anthropogenic, adopting the average crustal concentrations of metals reported by
Taylor (1964) as proxies for the metal background levels. Although this has become a
standard approach used by many authors (e.g. Addo et al., 2012; Mahu et al., 2015), there is a
need to exercise caution in the interpretation of the results.
General discussion and conclusions
249
For the characterisation of the dominant sources of PAH contamination in sediments, the
ΣLPAH/ΣHPAH ratio (Rocher et al., 2004) and various PAH isomeric ratios including
anthracene/[anthracene + phenanthrene], fluoranthene/[fluoranthene + pyrene] and
benzo(a)anthracene/[benzo(a)anthracene + chrysene] have been widely used (Yunker et al.,
2002; Abrajano et al., 2003; Rocher et al., 2004; Nyarko et al., 2011; Guerra, 2012). Chapter 4
showed that these PAH source diagnostic tools did not yield consistent results for the Tema
Harbour sediments. This is an interesting finding, which suggests that a number of indices
should be used when assessing PAH sources in sediments.
9.1.1.2. Bioassay testing of Tema Harbour sediment
Results from Chapters 4 and 5 indicated potential toxicity of the harbour sediments, which
required a more refined assessment. Whole-sediment toxicity bioassays are recommended as a
valuable tool in ecotoxicological assessment of contaminated sediments (Annicchiarico et al.,
2007; Ré et al., 2009; Schipper et al., 2010) as they integrate the toxic effects of contaminant
mixtures present in a sediment sample (Forrester et al., 2003; Escher et al., 2008). In many
countries, bioassays are now required in the assessment of dredged materials and for the
licensing of their subsequent disposal (DelValls et al., 2004; Rose et al., 2006; Casado-
Martinez et al., 2006, 2007; van Dam et al., 2008; Prato et al., 2011). Thus, in Chapter 6, the
standard acute 10-day C. volutator (Roddie and Thain, 2002; Schipper et al., 2006) and the
standard chronic 28-day H. diversicolor (Hannewijk et al., 2004) whole-sediment bioassays
were combined with chemical analysis, SQGs and ALs to characterise the potential
hazard/toxicity of the Tema Harbour sediments as a further line of evidence of sediment
pollution in the Tema Harbour. For the bioassay, mortality and metal bioaccumulation were
evaluated as endpoints.
The C. volutator and H. diversicolor whole-sediment bioassay tests were chosen for the
following reasons (Ciarelli et al., 1998; Uwadiae, 2010; Carvalho et al., 2012). First, these
protocols are standard (Roddie and Thain, 2002; Schipper et al., 2006; Hannewijk et al.,
2004). Secondly, they have been widely used in the scientific literature (Stronkhorst et al.,
2003; Scarlett et al., 2007; van den Heuvel-Greve et al., 2007; Moreira et al., 2006; Mayor et
al., 2008), but rarely as complementary test species. Thirdly, they are abundant, available
throughout the year and, easily accessible and maintained under laboratory conditions (Scaps,
2002; Bat, 2005). Fourthly, they are known to tolerate a wide range of salinities, temperatures,
General discussion and conclusions
250
sediment grain sizes and organic carbon contents (Ciarelli et al., 1998; Roddie and Thain,
2002; Scaps, 2002; Bat, 2005; Philippe et al., 2008). Lastly, they have wide geographic
distributions across polar, temperate and tropical marine regions (Bat, 2005; Moreira et al.,
2006; Uwadiae, 2010; Carvalho et al., 2012). In the case of the C. volutator whole-sediment
toxicity bioassay, a sediment toxicity classification scheme has been developed (EPA, 1998).
Although the use of local species from the study area as bioassay test organism is prefereable,
a biological baseline survey conducted on benthic species in the Tema Harbour in 2010 by
Nyarko et al. (unpublished) revealed the absence of C. valuator and H. diversicolor in the
harbour. Moreover, whole-sediment toxicity bioassays with tropical species are not yet well
developed (Adams and Stauber, 2008). Therefore, for this thesis, whole-sediment toxicity
bioassay tests on the tropical Tema Harbour sediments were conducted in Europe, using C.
volutator and H. diversicolor of European origin (Chapter 6).
The bioassay tests showed that the Tema Harbour sediments are hazardous as predicted by the
SQGs and the TEQs (Table 4.5; Table 5.4). Thus, the absence of these species at the Tema
Harbour may partly be due to their vulnerability to the toxicity of the harbour sediments.
Chapters 3-5 indicated that the bottom water within the harbour was anoxic, which could also
be unfavourable for C. valuator and H. diversicolor to thrive. The pH range (7.3-8.3) of the
harbour sediments (Chapter 5) was, however, comparable to the pH range (7.7-8.5) of the
overlying water in the bioassays (Chapter 6). Different benthic species may display different
sensitivities to sediment toxicity (Dauvin et al., 2016) and this was observed, C. volutator
being more sensitive than H. diversicolor (Figs. 6.2 and 6.3). The difference in the
sensitivities may be partly due to the presence of different toxicants in the harbour sediments
(Bat and Raffaelli, 1998; Forrester et al., 2003; Long et al., 2006; Mayor et al., 2008), i.e.
radionuclides (Chapter 3), DDTs, HCHs and PAHs (Chapter 4) and metals (Chapters 5 and 6).
Based on SQGs, the sediment concentrations of Pb, Ni, Cu, Zn and As may pose medium
potential ecotoxicological risks (Table 6.5). A logarithmic relationship was observed between
C. volutator mortality and sediment Cd concentration (Fig. 6.4a), whereas a linear relationship
was observed between H. diversicolor mortality and sediment Cu concentration (Fig. 6.4b),
suggesting Cd and Cu may play a role in the mortality of C. valuator and H. diversicolor,
respectively.
General discussion and conclusions
251
Amphipods are generally highly sensitive to low levels of hydrocarbon contamination,
whereas polychaetes are more tolerant (Dauvin et al., 2016). During the bioassay experiments,
petroleum contamination was visible in the sediments from the Fishing Harbour and the
Canoe Basin, possibly as a result of oil spills during refuelling of fishing vessels and fuel
leakage in these sampling areas (Chapter 6). Thus, PAH contamination could potentially
contribute to the toxicity in the Tema Harbour sediments. This requires further investigation
using appropriate sediment sampling techniques for PAH assessment. For this bioassay study,
the sediments were sampled in accordance with metal analysis.
Sediment toxicity to C. volutator and H. diversicolor may occur as a result of contaminant
uptake and subsequent bioaccumulation (Luoma and Rainbow, 2008; Rainbow et al., 2009).
The contaminated harbour sediments were predominantly composed of the silt-clay fraction,
which can be easily ingested by the test organisms (Bat and Raffaelli, 1998; Burton, 2002).
Therefore, to provide a further line of evidence of the potential biological effects of sediment
pollution in the Tema Harbour, Chapter 6 also evaluated the bioaccumulation potential of
sediment-bound metals (Cd, Pb, Cr, Ni, Cu, Zn and As) in the exposed C. volutator and H.
diversicolor based on the biota-sediment bioaccumulation factors (BSAFs) (Aydin-Onen et
al., 2015).
Compared with the control organisms, it was evident that metal bioaccumulation occurred in
both C. volutator and H. diversicolor exposed to the Tema Harbour sediments. This indicates
high potential bioavailability and risk of metals entering the food. Comparison of metal
concentrations in the Tema Harbour sediments with international Action Levels (Table 6.6)
indicated unacceptable levels of Cu and Zn in the harbour sediments. This, together with the
bioassay results, is of concern considering the adverse implications for the aquatic food web
and the disposal of dredged material at sea without any prior remediation at the Tema
Harbour. In year 2013, the Ghana Ports and Harbours Authority embarked on a port
expansion project aimed at increasing the vessel handling capacity at the Tema Harbour to
about 1,000,000 Twenty-Foot Equivalent Units (TEUs) in order to meet the growing needs of
the international maritime market (http://ghanaports.gov.gh/GPHA). Since then, undisclosed
quantities of sediments have been dredged and disposed of at sea (P.K. Ofori-Danson, pers.
comm.).
General discussion and conclusions
252
In this study, the metal concentrations in the tissues of both C. volutator and H. diversicolor
neither correlated statistically with the sediment total metal concentrations nor the
exchangeable metal fraction in the sediments, which poses the greatest risk of entering the
food chain (Jain, 2004; van Hullebusch et al., 2005; Dung et al., 2013; Kalwa et al., 2013; Pini
et al., 2015). These non-correlations suggest mediation of metal bioaccumulation by processes
such as detoxification (Rainbow and Luoma, 2011), storage or elimination in the organisms
(Adams et al., 2011).
9.1.2. Assessment of SARs in harbours
Sediment accumulation rates in harbours are a key factor that determines the timing of
dredging and the quantity of material to dredge. Information on sedimentation processes and
accurate quantification of SARs in harbours is therefore essential for harbour management
(Buesseler et al., 2007; Leys and Mulligan, 2011). The development of the 210
Pb sediment
dating technique has contributed to our understanding of the dynamics and functioning of
aquatic systems, with the unique ability to provide insight into the natural variability in
environmental conditions as well as anthropogenic impacts in sedimentary systems on time
scales spanning 100-150 years (Lu, 2007; Appleby, 2008; Díaz-Asencio et al., 2009). The
210Pb dating technique can be applied in establishing sediment chronology in lacustrine,
estuarine and marine environments, based on which sedimentation rates can be evaluated and
pollution history reconstructed.
Deriving accurate sediment chronology and evaluating sediment accumulation rates from
210Pb profiles in sediment cores is, however, not a simple and straight-forward task as the
usual assumptions involved in this technique could not be accomplished in perturbed
environments. The delivery of sediments and 210
Pb to aquatic systems is controlled by
complex processes which may not be well understood. Moreover, sediment mixing is a major
constraint in the quatification of recent SARs in disturbed environments such as harbours
since undisturbed sediments are the optimal materials for the applicability of the widely used
210Pb sediment dating models (Santschi et al., 2001; Bellucci et al., 2012).
In harbours, the movement of vessels and other activities such as dredging often induce
sediment resuspension and mixing (Lepland et al., 2010; Leys and Mulligan, 2011; Green and
Coco, 2014), disrupting natural sedimentation processes such as deposition (Klubi et al.,
General discussion and conclusions
253
2017) and the original imprint in the sediments (Santschi et al., 2001). Therefore, when
assessing sedimentation in harbours, the issue of mixing is quite pertinent. Mixing of particle-
bound tracers implies that the grain particles within the sediments are reworked, and the
causal mechanisms (physical, chemical and/or biological) must be identified, as well as their
depth-dependence. Thus, some authers incorporate sediment imaging techniques such as X-
radiography (Schmidt et al., 2007; Bellucci et al 2010, 2012; Lepland et al 2010) and
magnetic measurements (Bellucci et al., 2012) into the sediment core dating process to assess
sediment mixing. X-radiographic imaging and magnetic measurements are useful tools for
elucidating the sediment stratigraphy and variability in sediment texture and chemistry
(Schmidt et al., 2007a).
9.1.2.1. Assessment of SARs in the Tema Harbour
In this thesis (Chapter 7), a rigorous approach involving sediment traps, sediment cores and
the use of multitracers (7Be,
234Th and
210Pb) and different radiometric models was employed
to investigate suspended particulate matter (SPM) dynamics and quantify recent SARs in the
Tema Harbour. All the sediment cores were sampled out of the dredged area in the Tema
Harbour and were expected to have preserved a sequence of continuous sediment deposition.
Sediment mixing was examined by visual inspection of the core surfaces for biological
activity and analyses of short-lived radionuclides (7Be and
234Th) profiles in the upper layers
of the sediment cores (Erten, 1997; Schmidt et al., 2007a, b). Due to their short half-lives,
234Th and
7Be can provide reliable information on sediment mixing or particle reworking
processes over a period of 4-8 months (Schmidt et al., 2007a). Subsurface occurrence of 234
Th
and 7Be in areas of low sedimentation rates indicates post-depositional sediment mixing
(Schmidt et al., 2007b). Visual examination of the cores revealed no evidence of bioturbation
in the surficial layers, which can cause sediment mixing over large sediment mass depths. In
addition, specific activities of 7Be and
234Th were measured in the top layers of the sediment
cores to serve as a quality test for the complete surface recovery of the core, which is
necessary for dating (Erten et al., 1985; Erten, 1997). The depth profiles of these
radionuclides showed sharp gradients in the upper 2 cm layers (Table 7.2). Since this
observation is not consistent with a well-mixed layer, the hypothesis of mixing was rejected
(Section 7.3.4).
General discussion and conclusions
254
The sediment cores exhibited variable bulk density profiles (Fig. 7.2), from which highly
dynamic and non-steady sedimentation conditions were inferred. The sediment trap-derived
settling fluxes revealed the existence of local disturbances with a highly irregular spatial and
temporal character, which pointed to a complex dynamics of rising clouds of SPM and settling
in the Tema Harbour (Section 7.3.1).
9.1.2.1.1. Quantification of recent SARs in the Tema Harbour based on 7Be and 234Th
profiles and conventional 210Pb dating models
7Be,
234Th and
210Pb are useful complementary tracers for studying sedimentation processes
(Smoak and Patchineelam, 1999; Smoak et al., 1999; Yeager et al., 2005). Studies have shown
that it is necessary to recover sedimentation records of at least five decades in order to
calculate 210
Pb-derived sedimentation rates and nuclide inventories more rigorously (Su and
Huh, 2002). The analysed cores were too short (up to ≈50 cm) to allow any reliable
estimation of the total 210
Pbexc inventories required for the application of the constant rate of
supply (CRS) model (Fig. 7.5). Moreover, a clear monotonic exponential trend of decrease
was absent in the cores and thus, the application of the CF-CS model for deriving SAR values
was not reliable. The low values and large uncertainties in the 137
Cs data did not allow any
proper identification of chronostratigraphic horizons in the sediment cores, hence restricting
its use as a tracer for sedimentation (Pfitzner et al., 2004).
Under some simplifying assumptions of the Constant Flux Constant Sedimentation (CF-CS)
model, the 7Be profiles were used to obtain a first estimate of the order of magnitude of very
recent SARs over the past 6-8 months in the Tema Harbour ranging from 2.5 to 9.0 (± 1.3)
g.cm-2
.y-1
(Table 7.3). The 7Be-derived SAR values, along with the
210Pbexc specific activities
in the upper sediment layers, was then used to obtain a first estimate of the 210
Pbexc fluxes onto
the SWI for one core (core A = 25.6 kBq.m-2
.y-1
) (Section 7.3.4). This value is two orders of
magnitude higher than the expected atmospheric deposition of 210
Pbexc in the Tema Harbour
area (typically in the range of 100-200 Bq.m-2
.y-1
) (Section 7.3.4). The SAR values estimated
from the 7Be data were
consistent with the
234Th activity versus mass depth profiles, which
showed a near-constant background level along the cores at the 2-3 cm upper sediment slices
(Table 7.2).
General discussion and conclusions
255
9.1.2.1.2. Estimation of SARs from the 210Pb-based TERESA model
Despite the potential of the TERESA model (Abril, 2016), literature survey showed that it has
not yet been explored for dating sediment cores from disturbed sedimentary environments.
The model hypothesis of varying, but statistically correlated, fluxes of matter and 210
Pbexc onto
the SWI seemed reasonable for the Tema Harbour and thus, Chapter 7 explored the
applicability of the TERESA model (Abril, 2016) for deriving recent SARs in the harbour.
The TERESA model produced a sharp discontinuity in radionuclides profiles at the mass-
depth of 4.06 g.cm-2
(Section 7.3.6), which confirmed the hypothesis of negligible post
depositional processes. The TERESA model also produced a reasonable fit to the data and
generated SARs of 1.4-3.0 g.cm-2
.y-1
and accretion rates of 1.7-3 cm.y-1
for the Tema Harbour
(Section 7.3.9).
Although the TERESA model has been validated against synthetic cores and real data from
varved sediments, this is the first time it has been applied to date sediment cores from a
harbour. Other investigators have used integrated approaches to evaluate sedimentation rates
in harbours (Tang et al., 2008; Smith et al., 2009; Lepland et al., 2010; Yussof et al., 2015)
and disturbed bays (Bellucci et al., 2012), which could not be possible with the sole
application of 210
Pb models. The time-averaged SAR values for the Tema Harbour by the
TERESA model (1.4-3.0 g.cm-2
.y-1
) were very high in comparison to most of the data in the
literature for lacustrine and coastal environments from other climatic regions. The accretion
rates (1.7-3 cm.y-1
) were higher when compared with 0.57 cm.y-1
reported by Yussof et al.
(2015) for the Tanjung Pelepas Harbour (Malaysia), 1.2 cm.y-1
reported by Tang et al. (2008)
for the Victoria Harbour (Hong Kong) and 0.2-2 cm.y-1
reported by Smith et al. (2009) for the
Sydney Harbour (Nova Scotia, Canada).
9.1.2.2. Ecotoxicological implications of metal contamination in settling silt-clay
particles in the Tema Harbour
The fine fractions of sediments, particularly the silt-clay particles, can be easily ingested by
benthic organisms (Bat and Raffaelli, 1998; Bat, 2005). Therefore, chemical contamination of
silt-clay particles is a threat to benthic organisms and other organisms in the aquatic food
chain. Based on the ERL and ERM sediment quality guidelines (Long et al., 1995; Long et al.,
1998), Chapter 8 assessed the ecotoxicological implications of metal contamination in settling
silt-clay particles collected in the sediment traps (Chapter 7). The results showed that As
General discussion and conclusions
256
concentrations in the trapped silt-clay particles (146-1470 mg.kg-1
dw; see Table 8.1) far
exceeded its ERM value (70 mg.kg-1
dw; Table 8.7) by about 2-3 orders of magnitude. In
most cases, the concentrations of Cr (86%), Cu (86%), Zn (93%), Ni (71%) and Hg (77%) in
the trapped silt-clay particles were higher than their respective ERL values, but lower than
their corresponding ERM values (Table 8.7). Thus, the settling silt-clay particles were
potentially hazardous and pose medium to high ecotoxicological risks to benthic invertebrates
due to the concentrations of As, Cr, Cu, Zn, Ni and Hg.
The As concentrations in the settling silt-clay particles were higher than previously measured
As concentrations in bulk surface sediments (Table 5.1) or As concentrations in silt-clay
normalised sediments from the Tema Harbour (Table 6.6). Table 8.6 showed that the As
concentrations in the settling silt-clay particles were high compared with As concentrations
reported for sediments from gold mining areas in Ghana (Affum et al., 2016) and coastal
areas of Egypt (Mostafa et al., 2004; Abdel Ghani et al., 2013), Finland (Vallius et al., 2007),
China (Luo et al., 2010), Spain (Díaz-de Alba et al., 2011), Tanzania (Rumisha et al., 2012),
the Mediterranean (Mamindy-Pajany et al., 2013), and Saudi Arabia (Al-Taani et al., 2014;
Youssef et al., 2015; El-Sorogy et al., 2016). An increasing trend in As concentrations in the
settling silt-clay particles was observed across the sampling period (Fig. 8.1i), which
suggested the existence of continuous sources of As at the Tema Harbour. Potential As
sources include industrial activities such as metal smelting, the use of As-containing
agrochemicals in the harbour area and spillage of As-containing chemicals in the harbour.
9.2. General conclusions
This study is the first comprehensive assessment of sediments in the Tema Harbour in terms
of chemical pollution and accumulation rates. The thesis contributes to improving our ability
to combine sediment chemistry with bioassays in one comprehensive assessment of the
contamination state of a coastal harbour. The study results showed that the harbour has been
severely affected by anthropogenic activities, resulting in pollution of the sediments,
especially those from the Fishing Harbour and the Canoe Basin. This raises concerns about
sediment and general environmental management at the Tema Harbour, considering the lack
of engineered fields where dredged materials from the harbour can be stored or treated. The
expansion of the Tema Harbour and maintenance operations requires dredging and disposal of
the dredged material at sea may be the only option. In the context of this study, there is a need
General discussion and conclusions
257
to undertake remedial measures that will minimize the impact of dredging and the disposal of
dredged sediments from the harbour. Equally important is the need for enforcement of
environmental regulations to control point and non-point sources of pollution at the Tema
Harbour.
This thesis further demonstrates how sediment trap data can complement sediment core data
with the use of multi-tracers and radiometric dating models in the marine environment to
obtain reliable information on sediment dynamics in a disturbed coastal harbour area where
conventional 210
Pb-based dating methods fail. In particular, the 210
Pb-based TERESA model is
a good tool for quantifying sedimentation rates in the Tema Harbour with overall time-
averaged SAR values in the range of 1.4-3.0 g.cm-2
.y-1
and sediment accretion rates of 1.7-3
cm.y-1
. These accretion rates pose moderate problems for sustainable management of the
harbour. The main findings of the thesis for environmental management at the Tema Harbour
are presented in Fig.9.1.
Fig. 9.1 Schematic presentation of the main findings of the thesis for environmental
management at the Tema Harbour
Moderate
accumulation/
accretion rates
(Chapter 7)
Unsuitable for disposal at
sea without remediation
High potential
ecotoxicological
risk
Radionuclide (Chapter 3),
organic (Chapter 4) and
metal (Chapter 5)
contamination
Moderate sustainability
problem of dredging
for harbour
maintenance
Toxic to test organisms (C.
volutator and H. diversicolor)
with high potential for metal
bioaccumulation (Chapter 6)
Tema Harbour sediments
General discussion and conclusions
258
References
Abdel Ghani, S., El Zokm, G., Shobier, A., Othman, T., & Shreadah, M. (2013). Metal
pollution in surface sediments of Abu-Qir Bay and Eastern Harbour of Alexandria,
Egypt. The Egyptian Journal of Aquatic Research, 39(1), 1-12.
Abrahim, G.M.S. & Parker, R.J. (2008). Assessment of heavy metal enrichment factors and
the degree of contamination in marine sediments from Tamaki Estuary, Auckland,
New Zealand. Environ Monit Assess. 136, 227-238
Abrajano Jr, T. A., Yan, B., Song, J., Bopp, R., & O'Malley, V. (2007). High-Molecular-
Weight Petrogenic and Pyrogenic Hydrocarbons in Aquatic Environments. In D. H.
Editors-in-Chief: Heinrich & K. T. Karl (Eds.), Treatise on Geochemistry (pp. 1-50).
Oxford: Pergamon.
Adams, M.S. & Stauber, J.L. (2008). Marine whole sediment toxicity tests for use in
temperate and tropical Australian environments: current status. Aust. J. Ecotoxicol. 14,
155-167.
Adams, W.J., Blust, R., Borgmann, U., Brix, K.V., DeForest, D.K., Green, A.S., Meyer, J.S.,
McGeer, J.C., Paquin, P.R., & Rainbow, P.S. (2011). Utility of tissue residues for
predicting effects of metals on aquatic organisms. Integr. Environ. Assess. Manage. 7,
75-98.
Addo, M.A., Affum, H., Botwe, B.O., Gbadago, J.K., Acquah, S.A., Senu, J.K., Adom, T. &
Coleman, A. (2012). Assessment of Water Quality and Heavy Metal Levels in Water
and Bottom Sediment Samples from Mokwé Lagoon, Accra, Ghana. Res. J. Environ.
Earth Sci., 4(2), 119-130.
Affum, A.O., Osae Dede, S., Nyarko, B.J.B, Acquaah, S., Kwaansa-Ansah, E.E, Darko, G.,
Dickson, A., Affum, E., & Fianko, J.R. (2016). Influence of small-scale gold mining
and toxic element concentrations in Bonsa river, Ghana: A potential risk to water
quality and public health. Environ. Earth Sci., 75, 178-194.
Akrasi, S. (2011). Sediment discharges from Ghanaian rivers into the sea. West Afr. J. Appl.
Ecol. 18, 1-13.
Al-Taani, A.A., Batayneh, A., Nazzal, Y., Ghrefat, H., Elawadi, E., & Zaman, H. (2014).
Status of trace metals in surface seawater of the Gulf of Aqaba, Saudi Arabia. Marine
Pollution Bulletin, 86(1), 582-590.
Aydin-Onen, S., Kucuksezgin, F., Kocak, F., & Açik, S. (2015). Assessment of heavy metal
contamination in Hediste diversicolor (OF Müller, 1776), Mugil cephalus (Linnaeus,
General discussion and conclusions
259
1758), and surface sediments of Bafa Lake (Eastern Aegean). Environ. Sci. Pollut.
Res. 22, 8702-8718.
Bat, L. (2005). A review of sediment toxicity bioassays using the amphipods and polychaetes.
Turkish Journal of Fisheries and Aquatic Sciences, 5(2), 119-139.
Bat, L. & Raffaelli, D. (1998). Sediment toxicity testing: a bioassay approach using the
amphipod Corophium volutator and the polychaete Arenicola marina. J. Exp. Mar.
Bio. Ecol. 226, 217-239.
Bellucci, L. G., Giuliani, S., Romano, S., Albertazzi, S., Mugnai, C., & Frignani, M. (2012).
An Integrated Approach to the Assessment of Pollutant Delivery Chronologies to
Impacted Areas: Hg in the Augusta Bay (Italy). Environ. Sci. & Technol. 46(4), 2040-
2046.
Birch, G.F., & Hutson, P., 2009. Use of sediment risk and ecological/conservation value for
strategic management of estuarine environments: Sydney estuary, Australia. Environ.
Manage. 44, 836-850.
Birch, G.F. & Olmos, M.A. (2008). Sediment-bound heavy metals as indicators of human
influence and biological risk in coastal water bodies. ICES J. Mar. Sci. 65: 1407-1413.
Bolam, S.G., Rees, H.L., Somerfield, P., Smith, R., Clarke, K.R., Warwick, R.M., Atkins, M.
& Garnacho, E. (2006). Ecological consequences of dredged material disposal in the
marine environment: a holistic assessment of activities around the England and Wales
coastline. Mar. Pollut. Bull., 52(4), 415-26.
Buesseler, K.O., Antia, A.N., Chen, M., Fowler, S.W., Gardner, W.D., Gustafsson, O.,
Harada, K., Michaels, A.F., Rutgers van der Loeff, M. & Sarin, M. (2007). An
assessment of the use of sediment traps for estimating upper ocean particle fluxes. J
Mar Res 65(3), 345-416.
Burton, G.A. (2002). Sediment quality criteria in use around the world. Limnology, 3, 65-76.
Caille, N., Tiffreau, C., Leyval, C. & Morel, J.L., 2003. Solubility of metals in an anoxic
sediment during prolonged aeration. Sci. Total Environ. 301(1), 239-250.
Carvalho, S., Cunha, M.R., Pereira, F., Pousão-Ferreira, P., Santos, M., & Gaspar, M. (2012).
The effect of depth and sediment type on the spatial distribution of shallow soft-
bottom amphipods along the southern Portuguese coast. Helgol. Mar. Res. 66, 489-
501.
Casado-Martínez MC., Buceta JL, Belzunce MJ, DelValls TA (2006) Using sediment quality
guidelines for dredged material management in commercial ports from Spain. Environ.
Int. 32, 388-396.
General discussion and conclusions
260
Casado-Martinez, M.C., Forja, J.M., & DelValls, T.A., 2007. Direct comparison of amphipod
sensitivities to dredged sediments from Spanish ports. Chemosphere, 68, 677-685.
Choueri, R.B., Cesar, A., Abessa, D.M.S., Torres, R.J., Morais, R.D., Riba, I, Pereira, C.D.S.,
Nascimento, M.R.L., Mozeto, A.A. & DelValls, T.A. (2009). Development of site-
specific sediment quality guidelines for North and South Atlantic littoral zones:
Comparison against national and international sediment quality benchmarks. J.
Hazard. Mater. 170, 320-331.
Ciarelli, S., Vonck, W., Van Straalen, N., & Stronkhorst, J., 1998. Ecotoxicity assessment of
contaminated dredged material with the marine amphipod Corophium volutator. Arch.
Environ. Contam. Toxicol. 34, 350-356.
Dauvin, J.C., Andrade, H., de-la-Ossa-Carretero, J.A., Del-Pilar-Ruso, Y., Riera, R. (2016).
Polychaete/amphipod ratios: An approach to validating simplebenthic indicators.
Ecological Indicators, 63, 89-99.
DelValls, T., Andres, A., Belzunce, M., Buceta, J., Casado-Martinez, M., Castro, R., Riba, I.,
Viguri, J.R. & Blasco, J. (2004). Chemical and ecotoxicological guidelines for
managing disposal of dredged material. Trends Anal. Chem. 23, 819-828.
Díaz-Asencio, M., Alonso-Hernández, C. M., Bolanos-Álvarez, Y., Gómez-Batista, M., Pinto,
V., Morabito, R., . . . Sanchez-Cabeza, J. A. (2009). One century sedimentary record
of Hg and Pb pollution in the Sagua estuary (Cuba) derived from 210
Pb and 137
Cs
chronology. Marine Pollution Bulletin, 59(4–7), 108-115.
Díaz-de Alba, M., Galindo-Riaño, M. D., Casanueva-Marenco, M. J., García-Vargas, M. &
Kosore, C. M. (2011). Assessment of the metal pollution, potential toxicity and
speciation of sediment from Algeciras Bay (South of Spain) using chemometric tools.
J. Hazard. Mater. 190(1-3), 177-187.
Dung, T.T.T., Cappuyns, V., Swennen, R. & Phung, N.K. (2013). From geochemical
background determination to pollution assessment of heavy metals in sediments and
soils. Rev Environ Sci Bio/Technol, 12, 335-353.
El-Sorogy, A.S., Youssef, M., Al-Kahtany, K., & Al-Otaiby, N. (2016). Assessment of arsenic
in coastal sediments, seawaters and molluscs in the Tarut Island, Arabian Gulf, Saudi
Arabia. J. Afr. Earth Sci., 113, 65-72.
EPA, USACE (1998). Evaluation of dredged material proposed for discharge in waters of the
US-testing manual: Inland Testing Manual. EPA-823-B-98-004. US Environmental
Protection Agency and US Army Corps of Engineers, Washington, DC.
General discussion and conclusions
261
Erten, H., Von Gunten, H., Rössler, E. & Sturm, M. (1985). Dating of sediments from Lake
Zurich (Switzerland) with210Pb and 137
Cs. Swiss J Hydrol, 47(1), 5-11.
Erten H. (1997). Radiochronology of lake sediments. Pure Appl Chem, 69(1),71-76.
Escher, B.I., Bramaz, N., Mueller, J.F., Quayle, P., Rutishausera, S. & Vermeirssena, E.L.M
(2008). Toxic equivalent concentrations (TEQs) for baseline toxicity and specific
modes of action as a tool to improve interpretation of ecotoxicity testing of
environmental samples. J. Environ. Monit. 10, 612-621.
Forrester, G.E., Fredericks, B.I., Gerdeman, D., Evans, B., Steele, M.A., Zayed, K.,
Schweitzer, L.E., Suffet, I.H., Vance, R.R., & Ambrose, R.F., 2003. Growth of
estuarine fish is associated with the combined concentration of sediment contaminants
and shows no adaptation or acclimation to past conditions. Mar. Environ. Res. 56,
423-442.
Green, M.O. & Coco, G. (2014). Review of wave‐driven sediment resuspension and transport
in estuaries. Rev. Geophys. 52(1), 77-117.
Guerra, R. (2012). Polycyclic Aromatic Hydrocarbons, Polychlorinated Biphenyls and Trace
Metals in Sediments from a Coastal Lagoon (Northern Adriatic, Italy). Water, Air, &
Soil Pollut. 223(1), 85-98.
Hannewijk, A., Kater, B.J. & Schipper, C.A. (2004). Sediment toxiciteitstest met Nereis
diversicolor (In Dutch). 22 pp.
Hong, H., Xu, L.-J., Zhang, L., Chen, J., Wong, Y. & Wan, T. (1995). Special guest paper:
environmental fate and chemistry of organic pollutants in the sediment of Xiamen and
Victoria Harbours. Mar. Pollut. Bull. 31(4), 229-236.
Jain, C. (2004). Metal fractionation study on bed sediments of River Yamuna, India. Water
Res., 38, 569-578.
Jiang, J., Wang, J., Liu, S., Lin, C, He, M. & Liu, X. (2013). Background, baseline,
normalization, and contamination of heavy metals in the Liao River Watershed
sediments of China. J. Asian Earth Sci. 73, 87-94.
Kalwa, M., Quináia, S., Pletsch, A., Techy, L., & Felsner, M. (2013). Fractionation and
Potential Toxic Risk of Metals From Superficial Sediment in Itaipu Lake—Boundary
Between Brazil and Paraguay. Arch. Environ. Contam. Toxicol. 64(1), 12-22.
Kelderman P, Ang‘weya R, De Rozari P, Vijverberg T. (2012). Sediment characteristics and
wind-induced sediment dynamics in shallow Lake Markermeer, the Netherlands.
Aquat Sci 74(2), 301-313.
General discussion and conclusions
262
Klubi, E., Abril, J.M., Nyarko, E., Laissaoui, A. & Benmansour, M. (2017). Radioecological
assessment and radiometric dating of sediment cores from dynamic sedimentary
systems of Pra and Volta estuaries (Ghana) along the Equatorial Atlantic. J. Environ.
Radioact., 178-179, 1-11.
Lepland, A., Andersen, T.J., Lepland, A., Arp, H.P.H., Alve, E., Breedveld, G.D., & Rindby,
A., 2010. Sedimentation and chronology of heavy metal pollution in Oslo harbour,
Norway. Mar. Pollut. Bull. 60, 1512-1522.
Leys, V., & Mulligan, R.P. (2011). Modelling coastal sediment transport for harbour
planning: selected case studies. INTECH.
Long, E.R., Ingersoll, C.G. & MacDonald, D.D. (2006). Calculation and uses of mean
sediment quality guideline quotients: a critical review. Environ. Sci. Technol. 40(6),
1726-1736.
Long, E.R., Field, L.J., & MacDonald, D.D. (1998). Predicting toxicity in marine sediments
with numerical sediment quality guidelines. Environ. Toxicol. Chem., 17(4), 714-727.
Long, E.R., MacDonald, D.D., Smith, S. L., & Calder, F.D. (1995). Incidence of adverse
biological effects within ranges of chemical concentrations in marine and estuarine
sediments. Environ. Manage., 19(1), 81-97.
Lu, X. (2007). A note on removal of the compaction effect for the 210
Pb method. Appl. Radiat.
Isot, 65(1), 142-146.
Luo, W., Lu, Y., Wang, T., Hu, W., Jiao, W., Naile, J.E., Khim, J.S. & Giesy, J.P. (2010).
Ecological risk assessment of arsenic and metals in sediments of coastal areas of
northern Bohai and Yellow Seas, China. Ambio, 39(5-6), 367-375.
Luoma, S.N. & Rainbow, P.S. (2008). Metal contamination in aquatic environments: science
and lateral management. Cambridge University Press, Cambridge.
Mahu, E, Nyarko, E., Hulme, S. & Coale, K.H. (2015). Distribution and enrichment of trace
metals in marine sediments from the Eastern Equatorial Atlantic, off the Coast of
Ghana in the Gulf of Guinea. Mar. Pollut. Bull. 98, 301-307.
Mamindy-Pajany, Y., Bataillard, P., Séby, F., Crouzet, C., Moulin, A., Guezennec, A.-G.,
Hrel, C., Marmier, N., & Battaglia-Brunet, F. (2013). Arsenic in Marina Sediments
from the Mediterranean Coast: Speciation in the Solid Phase and Occurrence of
Thioarsenates. Soil Sed Contam: An Int. J., 22(8), 984-1002.
Mayor, D.J., Solan, M., Martinez, I., Murray, L., McMillan, H., Paton, G.I., & Killham, K.,
(2008). Acute toxicity of some treatments commonly used by the salmonid
General discussion and conclusions
263
aquaculture industry to Corophium volutator and Hediste diversicolor: Whole
sediment bioassay tests. Aquaculture, 285, 102-108.
Mestres M, Sierra J, Mösso C. & Sánchez-Arcilla, A (2010). Sources of contamination and
modelled pollutant trajectories in a Mediterranean harbour (Tarragona, Spain). Mar.
Pollut. Bull. 60, 898-907.
Moreira, S.M., Lima, I., Ribeiro, R., & Guilhermino, L. (2006). Effects of estuarine sediment
contamination on feeding and on key physiological functions of the polychaete
Hediste diversicolor: laboratory and in situ assays. Aquat Toxicol. 78, 186-201.
Mostafa, A.R., Barakat, A.O., Qian, Y., Wade, T.L., & Yuan, D. (2004). An overview of
metal pollution in the Western Harbour of Alexandria, Egypt. Soil Sed Contam: An
Int. J., 13(3), 299-311.
Muller, G., 1969. Index of geo-accumulation in sediments of the Rhine River. J. Geol., 2(3):
108-118.
Mulligan, C.N., Yong, R.N. & Gibbs, B.F. (2001). An evaluation of technologies for the
heavy metal remediation of dredged sediments. J. Hazard. Mater. 85, 145-163.
Nyarko, E., Botwe, B.O. & Klubi, E. (2011). Polycyclic aromatic hydrocarbons (PAHs) levels
in two commercially important fish species from coastal waters of Ghana and their
carcinogenic health risks. West Afr. J. Appl. Ecol., 19, 53-66.
Petrosillo, I., Valente, D., Zaccarelli, N. & Zurlini, G. (2009). Managing tourist harbors: Are
managers aware of the real environmental risks? Mar. Pollut. Bull. 58, 1454-1461.
Pfitzner, J., Brunskill, G. & Zagorskis, I. (2004). 137
Cs and excess 210
Pb deposition patterns in
estuarine and marine sediment in the central region of the Great Barrier Reef Lagoon,
north-eastern Australia. J. Environ. Radioact. 76(1), 81-102.
Philippe, S., Leterme, C., Lesourd, S., Courcot, L., Haack, U. & Caillaud, J. (2008).
Bioavailability of sediment-borne lead for ragworms (Hediste diversicolor)
investigated by lead isotopes. Appl. Geochem. 23, 2932-2944.
Pini J, Richir J, Watson G (2015) Metal bioavailability and bioaccumulation in the polychaete
Nereis (Alitta) virens (Sars): The effects of site-specific sediment characteristics. Mar.
Pollut. Bull., 95, 565-575.
Prato, E., Parlapiano, I. & Biandolino, F. (2011). Evaluation of a bioassays battery for
ecotoxicological screening of marine sediments from Ionian Sea (Mediterranea Sea,
Southern Italy). Environ Monit Assess, DOI 10.1007/s10661-011-2335-9.
Rainbow, P.S. & Luoma, S.N. (2011). Metal toxicity, uptake and bioaccumulation in aquatic
invertebrates – Modelling zinc in crustaceans. Aquat Toxicol. 105, 455-465
General discussion and conclusions
264
Rainbow, P.S., Smith, B.D. & Luoma, S.N. (2009). Differences in trace metal
bioaccumulation kinetics among populations of the polychaete Nereis diversicolor
from metal-contaminated estuaries. Mar Ecol Prog Ser., 376, 173-184.
Ré, A., Freitas, R., Sampaio, L., Rodrigues, A.M., & Quintino, V. (2009). Estuarine sediment
acute toxicity testing with the European amphipod Corophium multisetosum Stock,
1952. Chemosphere, 76, 1323-1333.
Rocher, V., Azimi, S., Moilleron, R., & Chebbo, G. (2004). Hydrocarbons and heavy metals
in the different sewer deposits in the ‗Le Marais‘ catchment (Paris, France): stocks,
distributions and origins. Sci. Total Environ., 323(1-3), 107-122.
Roddie, B., & Thain, J. (2002). Biological effects of contaminants: Corophium sp. sediment
bioassay and toxicity test: International Council for the Exploration of the Sea. ICES
Techniques in Marine Environmental Sciences No. 28, ISSN 0903-2606, Copenhagen,
.Denmark.
Romero, A.F., Asmus, M.L., Milanelli, J. C. C., Buruaema, L., Abessa, D.M.S. (2014). Self-
diagnosis method as an assessment tool for environmental management of Brazilian
ports. J. Integr. Coast. Zone Manage., 14(4):637-644.
Rose, A., Carruthers, A-M, Stauber, J., Lima, R & Blockwell, S. (2006). Development of an
acute toxicity test with the marine copepod Acartia Sinjiensis. Aust. J. Ecotoxicol, 12,
73-81.
Ruiz-Fernández, A.C., Frignani, M., Hillaire-Marcel, C., Ghaleb, B., Arvizu, M.D., Raygoza-
Viera, J.R. & Páez-Osuna, F. (2009). Trace metals (Cd, Cu, Hg, and Pb) accumulation
recorded in the intertidal mudflat sediments of three coastal lagoons in the Gulf of
California, Mexico. Estuar. Coasts. DOI 10.1007/s12237-009-9150-3.
Rumisha, C., Elskens, M., Leermakers, M., & Kochzius, M. (2012). Trace metal pollution and
its influence on the community structure of soft bottom molluscs in intertidal areas of
the Dar es Salaam coast, Tanzania. Marine Pollution Bulletin, 64(3), 521-531.
Santschi, P.H., Presley, B.J., Wade, T.L., Garcia-Romero, B., & Baskaran, M. (2001).
Historical contamination of PAHs, PCBs, DDTs, and heavy metals in Mississippi
River Delta, Galveston Bay and Tampa Bay sediment cores. Mar. Environ. Res. 52(1),
51-79.
Scaps, P. (2002). A review of the biology, ecology and potential use of the common ragworm
Hediste diversicolor (OF Müller)(Annelida: Polychaeta). Hydrobiologia, 470, 203-
218.
General discussion and conclusions
265
Scarlett, A., Rowland, S., Canty, M., Smith, E., & Galloway, T. (2007). Method for assessing
the chronic toxicity of marine and estuarine sediment-associated contaminants using
the amphipod Corophium volutator. Mar. Environ. Res. 63, 457-470.
Schipper, C., Rietjens, I., Burgess, R., Murk, A. (2010). Application of bioassays in
toxicological hazard, risk and impact assessments of dredged sediments. Mar. Pollut.
Bull. 60(11), 2026-2042.
Schipper, C.A., Burgess, R.M., van den Dikkenberg, L.C. (2006). Sediment toxiciteittest met
de slijkgarnaal Corophium volutator (In Dutch). 18 pp.
Schmidt S, Jouanneau J-M, Weber O, Lecroart P, Radakovitch O, Gilbert F, Jézéquel D.
(2007a). Sedimentary processes in the Thau Lagoon (France): from seasonal to
century time scales. Estuar Coast Shelf Sci; 72(3), 534-542.
Schmidt S, Gonzalez J-L, Lecroart P, Tronczyński J, Billy I, Jouanneau J-M. (2007b).
Bioturbation at the water-sediment interface of the Thau Lagoon: impact of shellfish
farming. Aquat Living Resour; 20(2), 163-169.
Sinex, S.A. & Helz, G.R. (1981). Regional Geochemistry of Trace Elements in Chesapeake
Bay Sediments. Environ. Geol. 3, 315-323.
Smith, J., Lee, K., Gobeil, C. & Macdonald, R. (2009). Natural rates of sediment containment
of PAH, PCB and metal inventories in Sydney Harbour, Nova Scotia. Sci. Total
Environ. 407(17), 4858-4869.
Smoak, J.M. & Patchineelam, S.R. (1999). Sediment mixing and accumulation in a mangrove
ecosystem: evidence from 210
Pb, 234
Th and 7Be. Mangroves and Salt Marshes, 3, 17-
27.
Smoak, J.M., Moore, W.S., Thunell, R.C. & Shaw, T.J. (1999). Comparison of 234
Th, 228
Th,
and 210
Pb fluxes with fluxes of major sediment components in the Guaymas Basin,
Gulf of California. Mar. Chem., 65, 177-194.
Stronkhorst, J. & Van Hattum, B. (2003). Contamination of concern in Dutch marine harbour
sediments. Arch. Environ. Contam. Toxicol., 45, 306-316.
Stronkhorst, J., Schipper, C.A., Brils, J., Dubbeldam, M., Postma, J. & van de Hoeven, N.
(2003). Using marine bioassays to classify the toxicity of Dutch harbour sediments.
Environ Toxicol Chem., 22 (7), 1535-1547.
Su, C.-C., & Huh, C.-A. (2002). 210Pb, 137Cs and 239,240Pu in East China Sea sediments:
sources, pathways and budgets of sediments and radionuclides. Mar. Geol., 183(1–4),
163-178.
General discussion and conclusions
266
Syvitski, J.P., Vörösmarty, C.J., Kettner, A.J. & Green, P. (2005). Impact of humans on the
flux of terrestrial sediment to the global coastal ocean. Science, 308(5720), 376-380.
Tang, C. W.-y., Ip, C. C.-m., Zhang, G., Shin, P. K. S., Qian, P.-y., & Li, X.-d. (2008). The
spatial and temporal distribution of heavy metals in sediments of Victoria Harbour,
Hong Kong. Mar. Pollut. Bull., 57(6-12), 816-825.
Taylor, S. (1964). Abundance of chemical elements in the continental crust: a new table.
Geochim Cosmochim Acta, 28, 1273-1285.
Uwadiae, R.E. (2010). An inventory of the benthic macrofauna of Epe Lagoon, southwest
Nigeria. J. Sci. Res. Develop. 12, 161-171.
Vallius, H., Ryabchuk, D., Kotilainen, A. (2007). Distribution of heavy metals and arsenic in
soft surface sediments of the coastal area off Kotka, northeastern Gulf of Finland,
Baltic Sea. In: Vallius, H. (Ed.), Holocene Sedimentary Environment and Sediment
Geochemistry of the Eastern Gulf of Finland, Baltic Sea, Geological Survey, Finland,
45:33-48.
van Dam, R.A., Harford, A.J., Houston, M.A., Hogan, A.C. & Negri, A.P. (2008). Tropical
marine toxicity testing in australia: a review and recommendations. Aust. J.
Ecotoxicol., 14, 55-88.
van den Heuvel-Greve, M., Postma, J., Jol, J., Kooman, H., Dubbeldam, M., Schipper, C., &
Kater, B. (2007). A chronic bioassay with the estuarine amphipod Corophium
volutator: Test method description and confounding factors. Chemosphere, 66, 1301-
1309.
van Hullebusch, E.D., Lens, P.N.L. & Tabak, H.H. (2005). Developments in bioremediation
of soils and sediments polluted with metals and radionuclides. 3. Influence of chemical
speciation and bioavailability on contaminants immobilization/mobilization bio-
processes. Rev. Environ. Sci. Biotechnol., 4(3), 185–212.
Witt, J., Schroeder, A., Knust, R. & Arntz, W.E. (2004). The impact of harbour sludge
disposal on benthic macrofauna communities in the Weser estuary. Helgol. Mar. Res.
58, 117-128.
Yeager, K., Santschi, P., Phillips, J. & Herbert, B. (2005). Suspended sediment sources and
tributary effects in the lower reaches of a coastal plain stream as indicated by
radionuclides, Loco Bayou, Texas. Environ. Geol. 47(3), 382-395.
Yilgor, S., Kucuksezgin, F., & Ozel, E. (2012). Assessment of metal concentrations in
sediments from Lake Bafa (Western Anatolia): an index analysis approach. Bulletin of
Environ. Contam. Toxicol., 89(3), 512-518.
General discussion and conclusions
267
Youssef, M., El-Sorogy, A., Al Kahtany, K., & Al Otiaby, N. (2015). Environmental
assessment of coastal surface sediments at Tarut Island, Arabian Gulf (Saudi Arabia).
Marine Pollution Bulletin, 96(1), 424-433.
Yunker, M.B., Macdonald, R.W., Vingarzan, R., Mitchell, R.H., Goyette, D. & Sylvestre, S.
(2002). PAHs in the Fraser River basin: a critical appraisal of PAH ratios as indicators
of PAH source and composition. Org. Geochem. 33(4), 489-515.
Yusoff, A.H., Zulkifli, S.Z., Ismail, A. & Mohamed, C.A.R. (2015). Vertical trend of trace
metals deposition in sediment core off Tanjung Pelepas Harbour, Malaysia. Procedia
Environ Sci, 30, 211-216.
269
Samenvatting
De haven van Tema in Ghana is al bijna zes decennia in bedrijf en is onderhevig aan een grote
toevoer van sedimenten en verontreinigingde sedimenten als gevolg van de intense
antropogene activiteiten in het havengebied. Dit proefschrift beoordeelde de sediment
verontreiniging in de Tema haven door gebruik te maken van de standaard 10-daagse
Corophium volutator en 28-daagse Hediste diversicolor sediment toxiciteit bioassays evenals
het bepalen van de concentraties van chemische contaminanten (DDT's, HCH's, PAK's en
metaal - Cd, Pb, Cr, Ni , Cu, Zn en As). De resultaten van de bioassays toonden significante
C. volutator en H. diversicolor mortaliteit, wat aangeeft dat de Tema Harbour-sedimenten
vervuild en toxisch zijn. Biota-sediment accumulatiefactoren onthulden verder een hoog
potentieel voor bioaccumulatie van de sediment-geassocieerde metalen, wat nadelige
gevolgen kan hebben voor de voedselketen. De sedimenten van de Tema haven zijn dus
ongeschikt voor baggeren en dumpen op zee zonder sanering.
Het proefschrift onderzocht verder de accumulatie percentages van sedimenten (SAR's) in de
Tema-haven door de gecombineerde analyse van sediment profielen en sediment profiel
gegevens. De sediment profielen vertoonden variabele bulk dichtheidsprofielen, wat wijst op
zeer dynamische en niet-stabiele sedimentatie omstandigheden. De brutoschattingen van zeer
recente sediment accumulatiesnelheden met behulp van het constante flux sedimentatie (CF-
CS) model lagen in het bereik van 2,5-9,0 g.cm-2
.y-1
. Deze waarden waren veel lager dan de
geschatte gemiddelde bezinkingsfluxen op basis van de gegevens uit sedimentenvallen (15,2-
53,8 g.cm-2
.y-1
), wat aangeeft dat resuspensie van de sedimenten een belangrijke rol speelt in
sedimentatie in de Tema haven. Conventionele 210
Pb modellen voor sediment datering konden
niet worden gebruikt om de SAR's in de Tema-haven te schatten. Het TERESA-model op
basis van 210
Pb bleek echter een goed hulpmiddel te zijn om de accumulatie van sedimenten in
de Tema haven te kwantificeren met tijdsgemiddelde waarden variërend tussen 1,4-3,0 g.cm-
2.y
-1 en met sediment accumulatiesnelheden van 1,7-3 cm.y
-1.
Concluderend heeft deze studie aangetoond dat de haven van Tema ernstig is aangetast door
antropogene activiteiten, resulterend in vervuiling van de sedimenten, vooral die van de
Visserijhaven en het Kanobasin. Bovendien kan de sediment accumulatie in de haven
gematigde problemen opleveren voor het duurzaam gebruik van de haven. Er is daarom
Samenvatting
270
behoefte aan verbetering van het sediment en milieubeheer in de haven van Tema en het
reguleren van de afvoer van het gebaggerde materiaal uit deze tropische kusthaven.
the Chairman of the SENSE board the SENSE Director of Education
Prof. dr. Huub Rijnaarts Dr. Ad van Dommelen The SENSE Research School has been accredited by the Royal Netherlands Academy of Arts and Sciences (KNAW)
Netherlands Research School for the Socio‐Economic and Natural Sciences of the Environment
D I P L O M A
For specialised PhD training
The Netherlands Research School for the
Socio‐Economic and Natural Sciences of the Environment (SENSE) declares that
Benjamin Botwe
born on 25 June 1974 in Accra, Ghana
has successfully fulfilled all requirements of the
Educational Programme of SENSE.
Delft, 29 June 2018
SENSE Coordinator PhD Education Dr. Peter Vermeulen
The SENSE Research School declares that Benjamin Botwe has successfully fulfilled all requirements of the Educational PhD Programme of SENSE with a
work load of 33.2 EC, including the following activities:
SENSE PhD Courses
o Environmental research in context (2014) o Research in context activity: ‘Co‐organizing UNESCO‐IHE PhD Symposium on: From
water scarcity to water security’, 03‐04 October 2016, Delft, The Netherlands
Other PhD and Advanced MSc Courses
o Sampling in space and time for survey and monitoring of natural resources, PE&RC graduate school, Wageningen University (2013)
o Speciation and Bioavailability of Metals, Organics and Nanoparticles, Wageningen University (2013)
o Summer School on Contaminated Sediments ‐ Characterization and Remediation, IHE Delft (2016)
Research Supporting Activities
o Extended literature review o Several published papers
Oral Presentations
o Short‐term sediment‐associated trace metal dynamics in coastal marine Tema Harbour (Ghana). YOUMARES 7 Conference, 11‐13 September 2016, Hamburg, Germany
o Settling fluxes and ecotoxicological risk assessment of fine sedimentary metals in Tema Harbour (Ghana). Conference on fisheries and coastal environment, 25‐27 September 2017, Accra, Ghana
Sediment pollution and accumulation in harbours are major environmental issues and studies that advance their solutions are essential for harbour sustainability. This thesis provides the first comprehensive assessment of chemical pollution in sediments and sediment accumulation rates in the tropical Tema Harbour (Ghana). This thesis contributes to improving our ability to use an integrated approach involving sediment chemistry and bioassays in one comprehensive assessment of the contamination state of a tropical coastal environment. Whole-sediment toxicity bioassays using the amphipod Corophium volutator and the polychaete Hediste diversicolor as bioindicators were combined with data on concentrations of total metal
and metal binding forms, radionuclides, organochlorine pesticides and polycyclic aromatic hydrocarbons in bottom sediments as well as total metal concentrations in settling silt-clay particles collected by sediment traps to characterise the hazard, risk and impact of sediments from the tropical coastal Tema Harbour. This thesis has demonstrated, for the first time, how sediment trap data can complement sediment core data with the use of multi-tracers, gamma spectrometry and the 210Pb-based TERESA model to obtain reliable information on sediment dynamics and recent sediment accumulation rates (SARs) in a disturbed tropical marine sedimentary system, which is not possible by using conventional 210Pb sediment dating models.
This book is printed on paper from sustainably managed forests and controlled sources