samsung ubigate ibg router setup - avaya · samsung ubigate ibg router setup 8 samsung ubigate ibg...

Samsung Ubigate iBG Router Setup

03-601783Issue 3

April 2007

© 2007 Avaya Inc.All Rights Reserved.

NoticeWhile reasonable efforts were made to ensure that the information in this document was complete and accurate at the time of printing, Avaya Inc. can assume no liability for any errors. Changes and corrections to the information in this document may be incorporated in future releases.

For full legal page information, please see the complete document, Avaya Legal Page for Software Documentation, Document number03-600758.To locate this document on the website, simply go to http://www.avaya.com/support and search for the document number in the search box.

Documentation disclaimerAvaya Inc. is not responsible for any modifications, additions, or deletions to the original published version of this documentation unless such modifications, additions, or deletions were performed by Avaya. Customer and/or End User agree to indemnify and hold harmless Avaya, Avaya's agents, servants and employees against all claims, lawsuits, demands and judgments arising out of, or in connection with, subsequent modifications, additions or deletions to this documentation to the extent made by the Customer or End User.

Link disclaimerAvaya Inc. is not responsible for the contents or reliability of any linked Web sites referenced elsewhere within this documentation, and Avaya does not necessarily endorse the products, services, or information described or offered within them. We cannot guarantee that these links will work all of the time and we have no control over the availability of the linked pages.

WarrantyAvaya Inc. provides a limited warranty on this product. Refer to your sales agreement to establish the terms of the limited warranty. In addition, Avaya’s standard warranty language, as well as information regarding support for this product, while under warranty, is available through the following Web site:http://www.avaya.com/support

Copyright Except where expressly stated otherwise, the Product is protected by copyright and other laws respecting proprietary rights. Unauthorized reproduction, transfer, and or use can be a criminal, as well as a civil, offense under the applicable law.

Avaya supportAvaya provides a telephone number for you to use to report problems or to ask questions about your product. The support telephone number is 1-800-242-2121 in the United States. For additional support telephone numbers, see the Avaya Web site: http://www.avaya.com/support.

http://www.avaya.com/support

http://www.avaya.com/support/

http://www.avaya.com/support

Issue 3 April 2007 3

Samsung Ubigate iBG Router Setup . . . . . . . . . . . . . . . . . . . 5Avaya Communication Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Session Initiation Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Avaya SIP Enablement Services . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Setting up Communication Manager . . . . . . . . . . . . . . . . . . . . . . . . 7

Setting up a node name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Adding a signaling group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Adding a SIP trunk group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Setting up SIP Enablement Services . . . . . . . . . . . . . . . . . . . . . . 10Defining configuration sets . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adding stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Changing station mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting up trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Adding another signaling group . . . . . . . . . . . . . . . . . . . . . . . . . 16Adding a trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Synchronizing dial plan changes . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Contents

Contents

4 Samsung Ubigate iBG Router Setup



Use this document to set up Avaya Communication Manager and Avaya SIP Enablement Services (SES) to work with the Samsung Ubigate iBG™ family of routers. Communication Manager and SIP Enablement Services are Avaya MultiVantage™ communications telephony applications.This document outlines the screens and fields that must be administered in Communication Manager so that Communication Manager can work with the Samsung Ubigate iBG router.

Avaya Communication Manager Avaya Communication Manager is an open, scalable, highly reliable and secure telephony application. Communication Manager organizes and routes voice, data, image and video transmissions. It can connect to private and public telephone networks, ethernet LANs, ATM networks, and the Internet. Communication Manager solves business challenges by powering voice communications and by integrating with value-added applications. Communication Manager provides user and system management functionality, intelligent call routing, application integration and extensibility, and enterprise communications networking.

Session Initiation Protocol Session Initiation Protocol (SIP) is an endpoint-oriented signaling standard that is defined by the Internet Engineering Task Force (IETF). SIP is a text-based protocol based on elements of Hypertext Transfer Protocol (HTTP) and Simple Mail Transfer Protocol (SMTP). SIP supports several types of communication sessions that include voice, video, and instant text messaging.

Avaya SIP Enablement Services Avaya SIP Enablement Services (SES) combines the standard functions of a SIP proxy or registrar server with SIP trunking support and duplicated server features. This combination creates a highly scalable, highly reliable SIP communications network supporting telephony, instant messaging, conferencing, and collaboration solutions.



Requirements For this procedure, you need:

● Samsung Ubigate iBG Router

● Avaya Communication Manager, release 3.1.3 or later.

● Avaya SIP Enablement Services (SES), release 3.1.1 or later

● DNS Server (customer provided)

Related documentation In the following documentation, you can find steps to set up Communication Manager, SIP Enablement Services (SES), and the Samsung Ubigate iBG router, that are not covered in this document.

● Documentation on how to set up Communication Manager can be found at www.avaya.com/support. The document titles and reference numbers that you need are:

- Administration for Network Connectivity for Avaya Communication Manager, 555-233-504

- Administrator Guide for Avaya Communication Manager, 03-300509

● Documentation on how to set up an SES server can be found at www.avaya.com/support. The document title and reference number that you need to reference is:

- Installing and Administering SIP Enablement Services Release 3.1.1, 03-600768

● All other documentation concerning the setup, installation, administration, use, and maintenance of the Samsung Ubigate iBG router is created by Samsung. Samsung documentation is available at www.samsungen.com.

http://support.avaya.com/japple/css/japple?PAGE=Product&temp.productID=136527


http://www.samsungen.com

Setting up Communication Manager


Setting up Communication Manager The first step in this process is to set up Communication Manager to work with your SIP Enablement Services (SES) server. This process provides a way for calls to be routed between Communication Manager and SES.

Note:Note: If you already have an SES server working with Communication Manager, you

can skip this section and go to Setting up trunks on page 15.

Setting up a node name In Communication Manager, you must first set up a node name and IP address to identify your SIP Enablement Services (SES) server. This information is used to populate other screens.

1. Type change node-names ip. Press Enter.The system displays the IP Node Names screen (IP Node Names screen on page 7).

Figure 1: IP Node Names screen

2. In a blank Name field, type the name of your SES server that the iBG router will be linked to. The Name field is free form text.

3. In the IP Address field, type the IP address of this SES server.

4. Click Enter to save your changes.

Adding a signaling group Create a unique signaling group that includes the SES server that the iBG router is linked to.

1. Type add signaling-group next. Press Enter.The system displays the Signaling Group screen and assigns the next available number (Signaling Group screen on page 8).

change node-names ip Page 1 of XIP NODE NAMES

Name IP Address Name IP AddressCMS-Barney 172.99.99.99SES-iBG 172.87.87.845



Figure 2: Signaling Group screen

2. In the Group Type field, type or select sip.

3. Make sure that the value in the Transport Method field is set to tls.

4. In the Near-end node Name field, type the name of either the Processor Ethernet or CLAN circuit pack to which the SES server registers.

5. In the Far-end node Name field, type the name of the SES server that you created in the previous procedure.

6. In both the Near-end Listen Port and Far-end Listen Port fields, type 5061.

7. In the Far-end Network Region field, type a network region number if your system is divided into network regions. This number should be the network region that the SES server is placed.

8. In the Far-end Domain field, type the registration domain name that is configured on the SES server.

! Important:Important: The Registration Domain name on the SES server configuration screen and the

name in the Far-end Domain field must match exactly. Blank spaces, underscores, and uppercase letters are not permitted. Dashes are permitted.

9. Accept the default values on the remaining fields.


add signaling-group next Page 1 of 1Signaling Group

Group Number: 19 Group Type: sipTransport Method: tls

Near-end node Name: jags-clan2c Far-end Node Name: SES-iBGNear-end Listen Port: 5061 Far-end Listen Port: 5061

Far-end Netowrk Region: 10Far-end Domain: fxo1.lzsamsung-ubigate-ibg-router.com

Bypass If IP Threshold Exceeded? n

DTMF over IP: rtp-payload Direct IP-IP Audio Connections? yIP Audio Hairpinning? n

Session Establishment Timer(min): 120



Adding a SIP trunk group

Tip:Tip: To get analog telephones to work with the Samsung Ubigate iBG router, analog

telephones must be set up in Communication Manager as SIP telephones. Avaya strongly suggests that you create a separate trunk group for all users of analog telephones. That way, you can more easily trace and isolate any problems that might occur. For more information on setting up an analog telephone, see Adding stations on page 12.

You now need to add SIP trunk groups.

1. Type add trunk-group next. Press Enter.The system displays the Trunk Group screen and assigns the next available trunk group number (Trunk Group screen on page 9).

Figure 3: Trunk Group screen

2. In the Group Type field, type or select SIP.

3. In the Group Name field, type a description of this trunk group as it relates to the Ubigate iBG router.

4. In the TAC field, type a valid number that fits your dial plan. For more information about dial plans in Communication Manager, see the Administrator Guide for Avaya Communication Manager, 03-300509, at www.avaya.com/support.

5. Make sure that the value in the Direction field is set to two-way.

6. In the Service Type field, type or select tie.

7. In the Signaling Group field, type the number of the signaling group that created in the previous procedure.

add trunk-group next Page 1 of XTrunk Group

Group Number: 7 Group Type: SIP CDR Reports: yGroup Name: fxo1 trunk on iBG COR: 1 TN: 1 TAC: 1006Direction: two-way Outgoing Display? n

Dial Access: n Night Service: ________Queue Length: 0Service Type: tie Auth Code? n

Signaling Group: 19Number of Members: 255




8. In the Number of Members field, type the number of members that you wish to use for this trunk group.

Tip:Tip: The maximum number of trunk group members in any one signaling group is 255.

The maximum number of total members is based upon your license agreement. If you have more than 255 trunk group members in a signaling group, you must create additional signaling groups.



Setting up SIP Enablement Services You now need to administer SIP Enablement Services (SES). The primary steps that you need to set up are:

● Adding a Media Server Extension

● Adding Users

Tip:Tip: Avaya suggests that you use the extension number of each user to populate the

Primary Handle field on the SES Add User screen. The primary handle information is used in other screens. By using the extension as the primary handle, any problems can more easily be traced back to the telephone.

! Important:Important: For each new user that you add, make sure that the Add Media Server

Extension field at the bottom of the Add User screen is checked.

● Editing the Media Server Map Entry

This document does not go into the specific steps to accomplish these tasks. These tasks are explained in the Installing and Administering SIP Enablement Services Release 3.1.1, 03-600768. You can find this document at www.avaya.com/support.




Defining configuration sets Before you can set up individual extensions in Communication Manager to work with the Ubigate iBG router, you must first define a configuration set. A configuration set is a set of rules that tells the system how to handle off-PBX calls.

1. Type change off-pbx-telephone configuration-set n, where n is the number of the configuration set. Press Enter.The system displays the Configuration Set screen for the configuration set that you typed (Configuration Set screen on page 11).

Figure 4: Configuration Set screen

2. In the Configuration Set Description field, type a description that helps you identify this as a set for SES telephones connected to the iBG router.



change off-pbx-telephone configuration-set 1 Page 1 of X

CONFIGURATION SET: 1

Configuration Set Description: iBG-connected phonesCalling Number Stype: networkCDR for Origination: phone-number

CDR for Calls to EC500 Destination? yFast Connect on Origination? nPost Connect Dialing Options: dtmfCellular Voice Mail Detection: none

Barge-In Tone? nCalling Number Verification? y

Identity When Bridging: principal



Adding stations You can now add individual stations (telephones) in Communication Manager. This process applies for all stations that work with the Samsung Ubigate iBG router.

Note:Note: Since analog stations need special administration, the following example

explains the specific steps how to set up an analog station using a 4620 station as an alias.

To add an analog telephone in Communication Manager:

1. Type add station n, where n is the extension. Press Enter.The system displays the Station screen for the extension that you typed (Station screen on page 12).

Figure 5: Station screen

2. In the Type field, type or select the model of telephone. In this example, type or select 4620.

The Port field shows IP.

Note:Note: By setting up an analog telephone as an IP telephone, you will get an error

message in the alarms log. You can disregard this error message.

3. In the Coverage Path 1 field, type the number of an appropriate coverage path to allow voice mail. If no coverage is desired, leave this field blank.

4. Administer the remaining fields on this page as required.

add station 7654321 Page 1 of XStation

Extension: 7654321 Lock Messages? n BCC: 0Type: 4620 Security Code: TN:Port: IP Coverage Path 1: 2 COR:Name: ext-7654321 Coverage Path 2: COS:

Hunt-to Station:

STATION OPTIONSLoss Group: 2 Personalized Ringing Patten: 1Data Module? n Message Lamp Ext: 7654321

Speakerphone: 2-way Mute Button Enabled? yDisplay Language:

Media Complex Ext: IP Softphone? n

Adding stations


5. Click Next until you see the Button Assignments area (Station screen on page 13).

Figure 6: Station screen

6. In the Site Data area, you can populate any of the fields that correlate with the extension.

7. If the extension is a member of abbreviated dialing groups, you can type the list numbers of the groups in the Abbreviated Dialing area.

8. In the Button Assignments area, type or select only two instances of call-appr.

Tip:Tip: An analog telephone can have no more than two call appearances. Leave the

remaining fields in the Button Assignments area blank.


add station 7654321 Page 3 of XStation

SITE DATARoom: Headset? nJack: Speaker? nCable: Mounting: dFloor: Cord Length:

Building: Set Color:

ABBREVIATED DIALINGList 1: ________ List 2: ________ List 3: ________

BUTTON ASSIGNMENTS1: call-appr 5: __________2: call-appr 6: __________3: __________ 7: __________4: __________ 8: __________



Changing station mapping Map all of the extensions to the configuration set that you just created, and to the trunk group that links to your SES server.

1. Type add off-pbx-telephone station-mapping. Press Enter.The system displays the Stations with Off-PBX Telephone Integration screen (Stations with Off-PBX Telephone Integration on page 14).

Figure 7: Stations with Off-PBX Telephone Integration

2. In the Station Extension field, type the telephone extension.

3. In the Application field, type or select OPS.

4. In the Dial Prefix field, type the telephone prefix, if any.

5. In the Phone Number field, type the complete telephone number.

6. In the Trunk Selection field, type the number of the trunk group that connects to your SES server.

Note:Note: The maximum number of trunk group members in any one signaling group is 255.

The maximum number of total members is based upon your license agreement. If there are more than 255 members trying to access the iBG router, you must type the value AAR in the Trunk Selection field instead of the number of the trunk group. Then you must set up AAR routing to the iBG router.

7. In the Configuration Set field, type the number of the configuration set that you just completed.


add off-pbx-telephone station-mapping Page 1 of XSTATIONS WITH OFF-PBX TELEPHONE INTEGRATION

Station Application Dial Phone Number Trunk ConfigurationExtension Prefix Selection Set7654321 OPS 7654321 10 17654322 OPS 7654322 10 17654323 OPS 7654323 10 1

Setting up trunks


Setting up trunks The next step in this process is to add trunks – such as SIP trunks – that are physically attached to the Samsung Ubigate iBG router. This process allows the iBG router to perform a gateway function that provides an interface to these trunks.

Note:Note: This administration is for trunks only, not the Communication Manager

connection to the SES Server.

A brief explanation

Communication Manager uses the Far-end Domain field on the Signaling Group screen to construct the SIP INVITE that is sent to the far end. The signaling group that we set up to connect Communication Manager to the SES (Adding a signaling group on page 7) applies to any SIP INVITE that is sent to SES.For example, if you call extension 12345 and that extension is a SIP telephone on the SES server, Communication Manager sends the INVITE to the SES server with the To field set to 12345@<far-end-domain-field>.

Note:Note: The <far-end-domain-field> is the value that is entered in the Far-end Domain

field on the Signaling Group screen.

If the SES server receives an INVITE for a domain that it does not control, SES must forward that INVITE to the correct place. By setting the Far-end Domain field to always be in the format “trunk-group-label.far-end-domain-field,” SES always sends the call to the iBG router instead of sending the call to the local station. The same is true of the reverse, using the original Far-end Domain field for all trunk groups on the iBG router. This is accomplished by adding a DNS entry, using the value in the Far-end Domain field, and pointing it to the IP address of the iBG router. See the second bullet item below.Without telling the SES server that this call is not local to it, the INVITE never completes to the iBG router. Even if the INVITE did complete, if the iBG has more than one trunk to the PSTN, it must know to which trunk to send the INVITE.Before you begin, make sure that you have:

● Completed the trunk group configuration on the iBG router. This configuration is where you obtain the Trunk Group Label that you will need later in this process.

● Made a Domain Name Service (DNS) server entry that resolves the Trunk Group Label to the signaling IP address on the iBG router. This entry is mapping names to IP addresses.

Both of these procedures are outside the scope of this document.



Adding another signaling group The first signaling group that you set up (see Adding a signaling group on page 7) was to administer the connection between Communication Manager and the SES server that the Samsung Ubigate iBG router is connected to.Now you need to ensure that any SIP INVITE messages are forwarded to the iBG router. To do that, you need to set up another signaling group. You need to configure the Far-end Domain field on the Signaling Group screen in the format <trunk-group-label>.<far-end-domain-field>.

Note:Note: For every trunk group that you set up, you must also set up a separate signaling

group.

To create a signaling group that identifies the iBG router as the recipient of SIP INVITE messages for our example SIP:

1. Type add signaling-group next. Press Enter.The system displays the Signaling Group screen and assigns the next available number (Signaling Group screen on page 16).

Figure 8: Signaling Group screen


3. Make sure that the value in the Transport Method field is set to tls.

4. In the Near-end node Name field, type the name of either the Processor Ethernet or CLAN circuit pack to which the SES server registers.

add signaling-group next Page 1 of 1Signaling Group

Group Number: 20 Group Type: sipTransport Method: tls

Near-end node Name: jags-clan2c Far-end Node Name: SES-iBGNear-end Listen Port: 5061 Far-end Listen Port: 5061

Far-end Netowrk Region: 10Far-end Domain: loop-start1.usae.wherever.com

Bypass If IP Threshold Exceeded? n

DTMF over IP: rtp-payload Direct IP-IP Audio Connections? yIP Audio Hairpinning? n

Session Establishment Timer(min): 120

Setting up trunks


5. In the Far-end node Name field, type the name of the SES server that you created in the Setting up a node name procedure.

6. In both the Near-end Listen Port and Far-end Listen Port fields, type 5061.

7. In the Far-end Network Region field, type a network region number if your system is divided into network regions. This number should be the network region that the SES server is placed.

8. In the Far-end Domain field, type the domain name.

! Important:Important: The format for the Far-end Domain field must be: the trunk group label in the iBG

router for that particular trunk, followed by a dot (.), followed by the SIP domain name in SES. For example, if the trunk group label is loop-start1, and the SIP domain name in SES is usae.wherever.com, then the value that you type in the Far-end Domain field is loop-start1.usae.wherever.com.

9. Make sure that the Far-end Domain field resolves in the DNS server to the Control Interface in the iBG router. Otherwise, calls cannot complete through the iBG router.

For an example how to set up and configure Microsoft DNS service, see the following site: www.microsoft.com/technet/archive/winntas/deploy/install.mspx?mfr=true.



Adding a trunk You must now set up the individual trunk groups that Communication Manager can process through the Samsung Ubigate iBG router. For an example, we will set up a SIP trunk.

1. Type add trunk-group next. Press Enter.The system displays the Trunk Group screen and assigns the next available trunk group number (Trunk Group screen on page 18).

http://www.microsoft.com/technet/archive/winntas/deploy/install.mspx?mfr=true



Figure 9: Trunk Group screen


3. In the Group Name field, type a description of this trunk group.

4. In the TAC field, type a valid number that fits your dial plan. For more information about dial plans in Communication Manager, see the Administrator Guide for Avaya Communication Manager, 03-300509, at www.avaya.com/support.

5. In the Service Type field, type or select tie.

6. In the Number of Members field, type a number that is equal to or less than the maximum number of physical circuits for that trunk on the iBG router.

For example, if you have an ISDN PRI trunk on the iBG router that has 23 B channels, the number of members in the Number of Members field can be no more than 23. If you have a CO trunk on the iBG router, the number of members in the Number of Members field can be no more than 1.

7. You can accept the default values on the remaining fields if you choose.


add trunk-group next Page 1 of 21 TRUNK GROUP Group Number: 20 Group Type: sip CDR Reports: y Group Name: iBG Analog trunk COR: 1 TN: 1 TAC: 802 Direction: two-way Outgoing Display? n Dial Access? n Night Service:Queue Length: 0Service Type: tie Auth Code? n Signaling Group: 2 Number of Members: 1


Synchronizing dial plan changes


Synchronizing dial plan changes Whenever you make changes to your dial plan in Communication Manager, you also need to synchronize those changes with the Samsung Ubigate iBG router.

Note:Note: The SES server automatically synchronizes with Communication Manager early

every day, but the iBG router does not synchronize unless you follow this procedure.

1. Make the necessary dial plan changes in Communication Manager.

2. Log into the SES server and get to a Linux command prompt.

3. From the Linux command prompt, type service ppm restart. Press Enter.This command restarts the PPM service and requests a new updated dial plan from Communication Manager.

4. Navigate to the SES Administration web interface on the iBG router home SES server.

5. Once at the Administration web interface, click Users, then click Show Registered Users.

6. From the screen that the system displays, either search for the registered iBG router, or search for every registered user.

7. On the search results screen, place a checkmark next to one or more of the iBG registered users.

8. At the bottom of the search results screen, click Reload.

The Reload command causes the SES server to send a message to the iBG router to download the dial plan changes.


Index

Index

AAvaya Communication Manager . . . . . . . . . . . 5Avaya SIP Enablement Services (SES) . . . . . . . . 5

SSamsung Ubigate iBG router . . . . . . . . . . . . . 5

administeringadding analog stations . . . . . . . . . . . . 12adding signaling group . . . . . . . . . . . 7, 16adding SIP trunk group . . . . . . . . . . . . 9adding stations . . . . . . . . . . . . . . . 12adding trunks . . . . . . . . . . . . . . . . 17changing station mapping . . . . . . . . . . 14defining configuration sets . . . . . . . . . . .11setting up Communication Manager and SES . . 7setting up node name . . . . . . . . . . . . . 7setting up SIP Enablement Services . . . . . 10setting up trunks. . . . . . . . . . . . . . . 15synchronizing dial plan changes . . . . . . . 19

commandsadd off-pbx-telephone station-mapping . . . . 14add signaling-group next . . . . . . . . . . 7, 16add station . . . . . . . . . . . . . . . . . 12add trunk-group next. . . . . . . . . . . . 9, 17change node-name ip . . . . . . . . . . . . . 7change off-pbx-telephone configuration-set . . .11service ppm restart . . . . . . . . . . . . . 19

descriptionAvaya Communication Manager . . . . . . . . 5Avaya SIP Enablement Services (SES) . . . . . 5related documentation . . . . . . . . . . . . . 6requirements . . . . . . . . . . . . . . . . . 6Session Initiation Protocol (SIP) . . . . . . . . 5

screensIP Node Names . . . . . . . . . . . . . . . . 7Signaling Group . . . . . . . . . . . . . . 8, 16Station . . . . . . . . . . . . . . . . . .12, 13Stations with Off-PBX Telephone Integration . 14Trunk Group . . . . . . . . . . . . . . . 9, 18

Session Initiation Protocol (SIP). . . . . . . . . . . . 5


Index

samsung ubigate ibg router setup - avaya · samsung ubigate ibg router setup 8 samsung ubigate ibg...

Documents