samsung crt cm27020s
DESCRIPTION
CRT Service manualTRANSCRIPT
![Page 1: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/1.jpg)
COLOR TELEVISION RECEIVERChassis : K15C Model : CM27020SX/KMT
COLOR TELEVISION RECEIVER CONTENTS
Precautions
Specifications and IC Data
Disassembly and Reassembly
Alignment and Adjustment
Troubleshooting
Exploded View and Parts List
Electrical Parts List
Block Diagram
Wiring Diagram
Schematic Diagrams
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
![Page 2: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/2.jpg)
ELECTRONICS
© Samsung Electronics Co., Ltd. AUG.2002Printed in KoreaAA82-00124A
![Page 3: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/3.jpg)
1. Precautions
1-1 Safety Precautions
1. Be sure that all of the built-in protectivedevices are replaced. Restore any missingprotective shields.
2. When reinstalling the chassis and its assemblies, be sure to restore all protectivedevices, including: nonmetallic control knobsand compartment covers.
3. Make sure that there are no cabinet openingsthrough which people—particularly children—might insert fingers and contactdangerous voltages. Such openings includethe spacing between the picture tube and thecabinet mask, excessively wide cabinetventilation slots, and improperly fitted back
covers.
If the measured resistance is less than 1.0megohm or greater than 5.2 megohms, anabnormality exists that must be correctedbefore the unit is returned to the customer.
4. Leakage Current Hot Check (Figure 1-1):Warning: Do not use an isolation transformer during this test. Use a leakage-current tester or a metering system that complies with American National StandardsInstitute (ANIS C101.1, Leakage Current forAppliances), and Underwriters Laboratories(UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plugthe AC line cord directly into the power outlet. With the unit’s AC switch first in theON position and then OFF, measure the current between a known earth ground (metalwater pipe, conduit, etc.) and all exposedmetal parts, including: antennas, handlebrackets, metal cabinets, screwheads and control shafts. The current measured shouldnot exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat thetest.
Fig. 1-1 AC Leakage Test
6. Antenna Cold Check: With the unit’s AC plug disconnected from theAC source, connect an electrical jumper acrossthe two AC prongs. Connect one lead of theohmmeter to an AC prong. Connect the otherlead to the coaxial connector.
7. X-ray Limits:The picture tube is especially designed to pro-hibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube onlywith one that is the same type as the original.Carefully reinstall the picture tube shields andmounting hardware; these also provide X-rayprotection.
8. High Voltage Limits:High voltage must be measured each time ser-vicing is done on the B+, horizontal deflectionor high voltage circuits. Correct operation ofthe X-ray protection circuits must be reconfirmed whenever they are serviced.(X-ray protection circuits also may be called
“horizontal disable” or “hold-down”.)
Heed the high voltage limits. These includethe X–ray Protection Specifications Label, andthe Product Safety and X-ray Warning Note onthe service data schematic.
Precautions
1-1
LEAKAGECURRENTTESTER
DEVICEUNDERTEST
TEST ALLEXPOSED METAL
SURFACES
2-WIRE CORD
ALSO TEST WITHPLUG REVERSED
(USING AC ADAPTERPLUG AS REQUIRED)
EARTHGROUND
(READING SHOULDNOT BE ABOVE
0.5mA)
Follow these safety, servicing and ESD precautions to prevent damage and protect against potentialhazards such as electrical shock and X-rays.
![Page 4: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/4.jpg)
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specifiedlimits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, checkeach of the special components.
10. Design Alteration Warning:Never alter or add to the mechanical or electrical design of this unit. Example: Do notadd auxiliary audio or video connectors. Suchalterations might create a safety hazard. Also,any design changes or additions will void themanufacturer’s warranty.
11. Hot Chassis Warning:Some TV receiver chassis are electrically connected directly to one conductor of the ACpower cord. If an isolation transformer is notused, these units may be safely serviced onlyif the AC power plug is inserted so that thechassis is connected to the ground side of theAC source.
To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the ACpower plug, reverse its polarity and reinsert.Re-measure the voltage between the chassisand ground.
12. Some TV chassis are designed to operate with85 volts AC between chassis and ground,regardless of the AC plug polarity. These unitscan be safely serviced only if an isolationtransformer inserted between the receiver andthe power source.
13. Some TV chassis have a secondary groundsystem in addition to the main chassis ground.This secondary ground system is not isolated from the AC power line. The twoground systems are electrically separated byinsulating material that must not be defeatedor altered.
14. Components, parts and wiring that appear tohave overheated or that are otherwise damaged should be replaced with parts thatmeet the original specifications. Always determine the cause of damage or overheat-ing, and correct any potential hazards.
15. Observe the original lead dress, especiallynear the following areas: Antenna wiring,sharp edges, and especially the AC and highvoltage power supplies. Always inspect forpinched, out-of-place, or frayed wiring. Donot change the spacing between componentsand the printed circuit board. Check the ACpower cord for damage. Make sure that leadsand components do not touch thermally hotparts.
16. Picture Tube Implosion Warning:The picture tube in this receiver employs“integral implosion” protection. To ensurecontinued implosion protection, make surethat the replacement picture tube is the sameas the original.
17. Do not remove, install or handle the picturetube without first putting on shatterproofgoggles equipped with side shields. Neverhandle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently attached deflection yoke; do nottry to remove such “permanently attached”yokes from the picture tube.
18. Product Safety Notice: Some electrical and mechanical parts havespecial safety-related characteristics whichmight not be obvious from visual inspection.These safety features and the protection theygive might be lost if the replacement compo-nent differs from the original—even if thereplacement is rated for higher voltage,wattage, etc.
Components that are critical for safety areindicated in the circuit diagram by shading, ( ) or ( ).
Use replacement components that have thesame ratings, especially for flame resistanceand dielectric strength specifications. A replacement part that does not have thesame safety characteristics as the originalmight create shock, fire or other hazards.
Precautions
1-2 Samsung Electronics
![Page 5: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/5.jpg)
1-2 Servicing Precautions
1. Servicing precautions are printed on the cabinet. Follow them.
2. Always unplug the unit’s AC power cord fromthe AC power source before attempting to: (a)Remove or reinstall any component or assembly, (b) Disconnect an electrical plug orconnector, (c) Connect a test component inparallel with an electrolytic capacitor.
3. Some components are raised above the printedcircuit board for safety. An insulation tube ortape is sometimes used. The internal wiring issometimes clamped to prevent contact withthermally hot components. Reinstall all suchelements to their original position.
4. After servicing, always check that the screws,components and wiring have been correctlyreinstalled. Make sure that the portion aroundthe serviced part has not been damaged.
5. Check the insulation between the blades of theAC plug and accessible conductive parts(examples: metal panels, input terminals andearphone jacks).
6. Insulation Checking Procedure: Disconnect thepower cord from the AC source and turn thepower switch ON. Connect an insulationresistance meter (500V) to the blades of the ACplug.
The insulation resistance between each bladeof the AC plug and accessible conductive parts(see above) should be greater than 1 megohm.
7. Never defeat any of the B+ voltage interlocks.Do not apply AC power to the unit (or any ofits assemblies) unless all solid-state heat sinksare correctly installed.
8. Always connect a test instrument’s groundlead to the instrument chassis ground beforeconnecting the positive lead; always removethe instrument’s ground lead last.
Precautions
1-3
Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.
Warning2: An electrolytic capacitor installed with the wrong polarity might explode.
![Page 6: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/6.jpg)
1. Some semiconductor (“solid state”) devicesare easily damaged by static electricity. Suchcomponents are called ElectrostaticallySensitive Devices (ESDs); examples includeintegrated circuits and some field-effect transistors. The following techniques willreduce the occurrence of component damagecaused by static electricity.
2. Immediately before handling any semiconductor components or assemblies, drain theelectrostatic charge from your body by touching a known earth ground. Alternatively,wear a discharging wrist-strap device. (Besure to remove it prior to applying power—this is an electric shock precaution.)
3. After removing an ESD-equipped assembly,place it on a conductive surface such as aluminum foil to prevent accumulation ofelectrostatic charge.
4. Do not use freon-propelled chemicals. Thesecan generate electrical charges that damageESDs.
5. Use only a grounded-tip soldering iron whensoldering or unsoldering ESDs.
6. Use only an anti-static solder removal device.Many solder removal devices are not rated as“anti-static”; these can accumulate sufficientelectrical charge to damage ESDs.
7. Do not remove a replacement ESD from itsprotective package until you are ready toinstall it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.
8. Immediately before removing the protectivematerial from the leads of a replacement ESD,touch the protective material to the chassis orcircuit assembly into which the device will beinstalled.
9. Minimize body motions when handlingunpackaged replacement ESDs. Motions suchas brushing clothes together, or lifting a footfrom a carpeted floor can generate enough static electricity to damage an ESD.
Precautions
1-4 Samsung Electronics
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
CAUTION
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that containedin the operating instructions unless you arequalified to do so.
![Page 7: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/7.jpg)
Samsung Electronics 2-1
Specifications and IC Data
2. Specifications and IC Data
2-1 Specifications
Television System:
Channels:
Intermediate Frequencies (MHz) :
Picture Tube:
Power Requirements:
Antenna Input Impedance:
Speaker Impedance
NTSC
NTSC
2 - 13
14 - 69
45.75
41.25
42.18
SystemBand
VHF
UHF
1 - 125CABLE
SYSTEM
IF Carrier Frequency
Picture IF Carrier
Sound IF Carrier
Color Sub Carrier
MODEL
CT
20 Inch
AC 120V, 60Hz
VHF, UHF : Telescopic dipole antenna (75 ohm unbalanced type )
8 ohm, 2W+2W (Dual Type)
SYSTEM
NTSC ONLY
A51QDX991X001 20Inch FLAT
25 Inch A63QDB891X 25Inch 1.0R, +380MG
29 Inch A68QDN891X001 29Inch 1.0R, +380MG
![Page 8: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/8.jpg)
2-2 Samsung Electronics
2-2 IC Line Up
Specifications and IC Data
Loc. No Specification Description Remark
IC501 TDA6107Q RGB DRIVE AMP
Table 2-1 IC Line-Up
IC202 24C04 EEPROM
PC801S TCET1108 / LTV817B PHOTO COUPLER
SPM456AN TDA9377, English/Spanish/FrenchIC201S Philips
Philips
Philips
FIAIR CHILD
VERTICAL OUTPUTLA7841
TDA7268
IC301
IC602 SOUND-AMP (2W x 2CH)
IC801SKA5Q0740RT (0765RT) POWER IC (STR)
IC802 KA7632 CUSTOM REGULATOR (5V, 8V, 3.3V)
IC101 LA7510 SIF - IC SANYO
IC601 MSP3425G Sound Processor Micronas
Sanyo
SEC
![Page 9: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/9.jpg)
2-3 Semiconductor Base Diagrams
Specifications and IC Data
Samsung Electronics 2-3
ELECTROLYTIC-CONDENSER
ICDIODE
SPM456AN(Pin 64)U4468B(Pin 16)MSP3425G(Pin 52)
IC TRANSISTOR
LA7841 TDA6107Q KA7632
TRANSISTORTRANSISTOR
KSC5802
BC
E E B C
KSC815-YKSA539-Y
SAW-FILTER
E C B
KSC2331-Y
111
M3953MM9261M
Fig. 2-1 Semiconductor Base Diagrams
![Page 10: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/10.jpg)
2-4
MEMO
![Page 11: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/11.jpg)
Disassembly and reassembly
Samsung Electronics 3-1
3. Disassembly and Reassembly
3-1 Back Cover Removal
1. After removing the screws, press the tension rib and pull the cabinet backwards.
2. To reassemble, press the tension rib (see diagram).
![Page 12: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/12.jpg)
Disassembly and reassembly
3-2 Samsung Electronics
3-2 Main Board Removal
3-3 Speaker Removal
1. Separate the socket board from the CRT neck.
2. Remove the Anode Cap from the CRT.
3. Remove the main board by pulling it with both hands.
Warning: The FBT is charged with high voltage. Before removing the Anode Cap, discharge the voltage through one of the heat sinks on the main board.
1. Remove the speaker bypressing the tension rib.
![Page 13: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/13.jpg)
Disassembly and reassembly
Samsung Electronics 3-3
3-4 CRT Removal
1. Spread a soft mat on the floor. Place the TV set facedown.
2. Remove the 4 nuts mounting the CRT to the front cabi-net. Lift the CRT.
3. Caution: Because of the high vacuum and large surfacearea of the picture tube, be careful while handling it: (1)Always lift the picture tube by grasping it firmly aroundthe faceplate, (2) Never lift the tube by its neck. (3) Donot scratch the picture tube or apply excessive pressure.Fractures of the glass may cause an implosion.
![Page 14: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/14.jpg)
3-4 Samsung Electronics
MEMO
![Page 15: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/15.jpg)
Alignment and Adjustments
Samsung Electronics 4-1
4. Alignment and Adjustments
4-1 Preadjustment
4-1-1 Factory Mode
1. Do not attempt these adjustments in the VideoMode.
2. The Factory Mode adjustments are necessarywhen either the EEPROM (IC902) or the CRTis replaced.
3. Do not tamper with the “Adjustment” screenof the Factory Mode menu. This screen isintended only for factory use.
4-1-2 When EEPROM (IC902) Is Replaced
1. When IC902 is replaced all adjustment datarevert to initial values. It is necessary tore-program this data.
2. After IC902 is replaced, warm up the TV for10 seconds.
4-1-3 When CRT Is Replaced
1. Make the following adjustments AFTER set-ting up after setting up purity and conver-gence :
White Balance Sub-Brightness Vertical Center Vertical SizeHorizontal Size Fail Safe (This adjustment must be the laststep).
2. If the EEPROM or CRT is replaced and set SCas 35(factory mode).
4-2 Factory/Service Mode
4-2-1 Procedure for the “Adjustment” Mode
1. This mode uses the standard remote control.The Service Mode is activated by entering thefollowing remote-control sequence :
(1) DISPLAY → FACTORY.
(2) STAND-BY → MUTE → 1 → 8 → 2→POWER ON.
2. The “SERVICE (FACTORY)” message will bedisplayed. The Service Mode has four compo-nents: ADJUST, OPTION , G2-ADJUST andRESET.
3. Access the Adjustment Mode by pressing the“VOLUME” keys ( Up or Down). The adjust-ment parameters are listed in the accompany-ing table, and selected by pressing the CHAN-NEL keys ( , ).
4. Selection sequences for the all system:
DOWN or UP key:
SCT>SBT>BLR>BLB>RG>GG>BG>VSL>VS>VA>HS>SC>CDL>STT>AKB>PDL>NDL>PSR>NSR>SCBT>VOL>CAP>MVOL>RP00>RP01>FMWS>AGC1>OMD>SCL>PWL>MUS>AGC>DSK>DVDB
5. The VOLUME keys increase or decrease theadjustment values (stored in the non-volatile memory) when Adjustment Modeis cancelled.
6. Cancel the Adjustment Mode by re-pressingthe “FACTORY” or “Power OFF” keys.
![Page 16: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/16.jpg)
4-2-2 Main Adjustment Parameter
Alignment and Adjustments
4-2 Samsung Electronics
SCT Su b Co n t ra s t 0 ~ 23
0 ~ 23SBT Su b Br i g h t n e s s
BLR
Bl a c k Le v e l o f fse t Blu eBLB
Bl a c k Le v e l o f fse t Red
RG R e d G a i n 0 ~ 6 3
GG G re e n G a i n 0 ~ 6 3
0 ~ 6 3
0 ~ 6 3
BG Bl u e G a i n 0 ~ 6 3
VSL Ve r t i ca l S lo p e 0 ~ 6 3
VS Ve r t i ca l Sh i f t 0 ~ 6 3
VA Ve r t i ca l A m p l i tu d e 0 ~ 6 3
HS H o r i z o n t a l Sh i f t 0 ~ 6 3
SC S- Co r r e c t i o n 0 ~ 6 3
CD L Ca t h o d e Dr i ve Le ve l 0 ~ 1 5
ST T Su b T i n t 0 ~ 7
AKB AKB On / o f f 0 ~ 1
0 ~ 1
0 ~ 1
0 ~ 1
0 ~ 1
0 ~ 1
0 0~ 1
0 ~ 3
0 ~ 3
P D L P AL De l a y 0 ~ 1 5
0 ~ 1 5
0 ~ 1 5
0 ~ 5 0
ND L NT SC De l ay 0 ~ 1 5
PSR P A L Su b c o l o r 0 ~ 2 3
NSR N T SC Su b c o l o r 0 ~ 2 3
SCBT Screen Br ighr tness 0 ~ 6 3
VO L Vo l u me p re s e t t i n g 0 ~ 6 3
0 ~ 6 3
0 ~ 6 3
CAP Capt ion Pos i t ion
Melody Sound Vo lume
Rat io P re / overshoot
Rat io P re / overshoot
Window Se lect ion Sound PLL
IF AGC Speed
Offset I F Demodulator
Sof t C l ipp ing Leve l
Peak Whi te L imi t t ing
Matr ix USA
Automat ic Ga in Cont ro l
Dynamic Sk in Tone
DVD Br ight Of fset
MVOL
RP00
RP01
FMWS
AGC1
OMD
SCL
PWL
MUS
AGC
DSK
DVDB
15
8
35
32
40
30
42
30
31
20
32
35
11
3
0
2
1
20
3
35
10
12
7
1
1
0
1
32
3
15
0
33
0
5
(16)
(6)
(37)
(33)
(38)
30
(39)
(32)
31
(20)
(33)
35
11
3
0
2
1
20
3
35
10
12
7
1
1
0
1
32
3
15
0
33
0
4
W/B Adjustment
W/B Adjustment
W/B Adjustment
W/B Adjustment
W/B Adjustment
FIX
W/B Adjustment
Vertical Picture Adjusment
FIX
Vertical Picture Adjusment
Picture Adjusment
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX (Mono)
FIX (Nomal)
FIX (No Crrection)
FIX (Off)
FIX (100%)
FIX (Mono)
FIX
FIX
FIX
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
ONO SD F U N CT I ON R A N G E I N I T I A L D AT A SETTING RE MARK
![Page 17: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/17.jpg)
Alignment and Adjustments
Samsung Electronics 4-3
4-2-3 Option Bytes
In the Service Mode, various can be selected via the Option Table. Example:
1
2
3
4
5
6
7
8
9
10
11
12
13
Option Table : xx xx
OSD
VIDEO MUTE
AUDIO
E/W
ZOOM
AUTO POWER
AUDIO MUTE
LANGUAGE
HOTEL MODE
BULE SCREEN
2'nd SIF
V-CHIP
AV Option
DEMO
SETTING
OFF
STEREO
OFF
NOR/ZOOM
OFF
ON
ENGLISH
OFF
OFF
INTERNAL
ON
AV + DVD
OFF
- Video Mute On/Off changing the channel
- Audio Option (Mono / Steeo)
- E/W Option
- Picture Size Option
- Master S/w Option
- Audio Mute On/ Off without signal
- Inital Language agter Factory Reset
- Hotel mode On/ Off
- Bule Screen On/ Off without signal
- SIF Option at Mono sound
- V-CHIP On/Off
- DVD, S-VHS Option
- DEMONSTRATION On/Off
REMARK
![Page 18: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/18.jpg)
Alignment and Adjustments
4-4 Samsung Electronics
4-3 Other Adjustments
4-3-1 General
1. Usually, a color TV needs only slight touch-up adjustment upon installation. Check thebasic characteristics such as height, horizontaland vertical sync and focus.
2. The picture should have good black and whitedetails. There should be no objectionablecolor shading; if color shading is present, per-form the purity and convergence adjustmentsdescribed below.
3. Use the specified test equipment or its equiva-lent.
4. Correct impedance matching is essential.
5. Avoid overload. Excessive signal from a sweepgenerator might overload the front-end of theTV. When inserting signal markers, do notallow the marker generator to distort testresults.
6. Connect the TV only to an AC power sourcewith voltage and frequency as specified on thebackcover nameplate.
7. Do not attempt to connect or disconnect anywires while the TV is turned on. Make surethat the power cord is disconnected beforereplacing any parts.
8. To protect against shock hazard, use an isola-tion transformer.
4-3-2 Automatic Degaussing
A degaussing coil is mounted around the pic-ture tube, so that external degaussing aftermoving the TV should be unnecessary. Butthe receiver must be properly degaussed uponinstallation.
The degaussing coil operates for about 1 sec-ond after the power is switched ON. If the sethas been moved or turned in a different direc-tion, disconnect its AC power for at least 30minutes.
If the chassis or parts of the cabinet becomemagnetized, poor color purity will result. Ifthis happens, use an external degaussing coil.Slowly move the degaussing coil around thefaceplate of the picture tube and the sides andfront of the receiver. Slowly withdraw the coilto a distance of about 6 feet before removingpower.
4-2-4 RESET
The Reset Mode is used during factory inspection. Function Reset:
1. Picture Mode Custom2. Sound Mode Custom3. Auto Volume Off4. Melody On5. Surround Off6. Turbo Sound Off 7. MTS Stereo8. Language English9. Caption Off10. Timer Off
![Page 19: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/19.jpg)
Alignment and Adjustments
Samsung Electronics 4-5
4-3-3 High Voltage Check
CAUTION: There is no high voltage adjustment on this chassis.The B+ power supply must be set to +125 volts (Full color bar inputand normal picture level).
1. Connect a digital voltmeter to the secondanode of the picture tube.
2. Turn on the TV. Set the Brightness andContrast controls to minimum (zero beam cur-rent).
3. The high voltage should not exceed 30KV.
4. Adjust the Brightness and contrast controls toboth extremes. Ensure that the high voltagedoes not exceed 30KV under any conditions.
4-3-4 FOCUS Adjustment
1. Input a black and white signal.
2. Adjust the tuning control for the clearest pic-ture.
3. Adjust the FOCUS control for well definedscanning lines in the center area of the screen.
4-3-5 Cathode Voltage Adjustment(Screen Adjustment)
1. Connect CRT socket pin GK to an oscilloscopeprobe.
2. Input a gray scale pattern. (Use a pattern gen-erator, PM5518)
3. Use the P mode key (on the remote control)for the STANDARD picture.
4. Adjust the Screen VR (on the FBT) so that thevoltage on the oscilloscope becomes 125+2.5V(See Fig. 4-1).
4-3-6 Purity Adjustment
1. Warm up the receiver for at least 20 minutes.
2. Plug in the CRT deflection yoke and tightenthe clamp screw.
3. Plug the convergence yoke into the CRT andset in as shown in Fig. 4-2.
4. Input a black and white signal.
5. Fully demagnetize the receiver by applying anexternal degaussing coil.
6. Turn the CONTRAST and BRIGHTNESS con-trols to maximum.
7. Loosen the clamp screw holding the yoke.Slide the yoke backward or forward to pro-vide vertical green belt. (Fig. 4-3).
8. Tighten the convergence yoke.
9. Slowly move the deflection yoke forward,and adjust for the best overall green screen.
10. Temporarily tighten the deflection yoke.
11. Produce blue and red rasters by adjusting thelow-light controls. Check for good purity ineach field.
12. Tighten the deflection yoke.
Fig. 4-1
125 2.5V+_
GND
_
![Page 20: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/20.jpg)
Alignment and Adjustments
4-6 Samsung Electronics
4-3-7 White Balance Adjustment
Fig. 4-2 Convergence Magnet Assembly
4 Pole Magnet
6 Pole Magnet 2 Pole Magnet
ClamperScrew
2 POLEPURITY
YOKECLAMPSCREW
6 POLECONVERGENCE
4 POLECONVERGENCE
ADJ(VE
Fig. 4-3 Center Convergence Adjustment
31m/m
Vertical Green Belt
Fig. 4-4
1
2
(a) Set up
1. Warm up the TV for at least 30 minutes in theAging Mode (OSD White). This mode is dis-played by entering the following sequence:
DISPLAY →FACTORY → FACTORY
2. Input a Toshiba pattern.
(b) Low-Light Adjustment
1. Set SBT to 1.0 fL in the Factory Service Mode with using CA100. See Fig. 4-4.
2. Adjust RG,BG so that the levels are suitable toeach local area.
(c) High-Light Adjustment
1. Set SCT to 35 FL in the Factory Service Modewith using CA100. See Fig. 4-4 .
![Page 21: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/21.jpg)
Alignment and Adjustments
Samsung Electronics 4-7
4-3-8 Center Convergence Adjustment
1. Warm up the receiver for at least 20 minutes.
2. Adjust the two tabs of the 4 pole magnets tochange the angle between them. Superimposethe red and blue vertical lines in the centerarea of the screen.
3. Adjust the Brightness and Contrast controlsfor a well defined picture.
4. Adjust the two-tab pairs of the 4 pole mag-nets, and change the angle between them.Superimpose the red and the blue verticallines in the center area of the screen.
5. Turn the both tabs at the same time, keepingthe angle constant, and superimpose the redand blue horizontal line in the center of thescreen.
6. Adjust the two-tab pairs of the 6-pole magnetsto superimpose the red and blue line onto thegreen. (Changing the angle affects the verticallines, and rotating both magnets affects thehorizontal lines.)
7. Repeat adjustments 2~6, if necessary.
8. Since the 4-pole magnets and 6-pole magnetsinteract, the dot movement is complex(Fig. 4-5).
Fig. 4-5 Center Convergence Adjustment
REDBLUE
BLUE
RED
4-Pole Magnet Movement
GREENRED/BLUE
RED/BLUE
GREEN
6-Pole Magnet Movement
![Page 22: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/22.jpg)
4-3-9 RF AGC Adjustment
Set the AGC data to 33 (Factory Mode).
4-3-10 Sub-Color Adjustment
Set data to (Factory Mode).
4-3-11 Geometry Adjustment
SC →VS→VA→VSL→HS
1. Input a lion head pattern.
2. Set the SC (S-Correction) as 35 and VS(VerticalShift) 31 so that the lion head circle becomesoval.
3. Adjust with VA (Vertical Amplitude) so thatthe top margin of the picture is 4.
Fig. 4-7
4. Adjust with VSL (Vertical-Slope) so that thebottom margin of the picture is 4.
Fig. 4-8
5. Adjust with HS (Horizontal Shift) so that thelion-head pattern and CRT centers are aligned.
Fig. 4-9
6. Adjust HS (Horizontal Shift) so that the leftand right margins of the picture are 5.
Alignment and Adjustments
4-8 Samsung Electronics
4
5 5
4
PSRNSR
203
![Page 23: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/23.jpg)
Samsung Electronics
Troubleshooting
5-1
5. Troubleshooting
5-1 No Power
Abnormal
Normal
Normal
Normal
Normal
Normal
Abnormal
Abnormal
Abnormal
Abnormal
Counectthe Power code
Check the X-tal,SDA,SCL port
of IC201S
Check the (33)Pin (H-Drive)
of IC201S
Check the130V- A Line
Check the 3.3V-A,8V-A Line
of IC201S
Check/ReplaceIC802
ReplaceIC201 S
Check theFBT,D805(D806)
Check the12.5V-A Line
Check theFD801S, D807, IC801S
or AC-Fuse
Check / ReplaceQ401
![Page 24: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/24.jpg)
5-2 Samsung Electronics
5-2 No Video (Sound OK)
Troubleshooting
Nornal
Nornal
Nornal
Nornal
Nornal
NornalNornal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Check RK,GK,BKSignal
Check R,G,BSignal into CRT
PCB
Check theresistance of R425
Check IC201SPin 49(BCL-IN)
Pin50(IK)
Check IC501B+(180V-B)
Check theVoltage of heater
CheckCRT and FBT
Check/ReplaceD812,FBT
Re-AdjustScreen Voltage
ReplaceR425
CheckCRT and FBT
Check/ReplaceIC201S
Check/ReplaceR421,R422,D505
Check IC201SPin 51,52,53
(R.G.B)
![Page 25: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/25.jpg)
5-3 No Sound (Video OK)
Troubleshooting
Samsung Electronics 5-3
Normal
NormalNormal
Normal
Normal
Normal
Normal
Normal
Checkthe signalOutput from CN602
CN601
Check Speaker and Wire
Check/ReplaceIC601
CheckB+ Line
5V-B, 8V-B
CheckIC101,TUNER
Check/ReplaceIC201S
SeeNo Power
CheckIC101,TUNER
ReplaceIC602
ReplaceIC610,R612
ReplaceFD801S,D807
Check IC602Pin2,7
Check IC601Pin47(SIF)
Check IC601B+
Check IC201SPin32(SIF)
Check IC602B+
Check R610,R612
Check FD801SD807
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
* MONO* STEREO
![Page 26: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/26.jpg)
5-4 Samsung Electronics
Troubleshooting
5-4 Horizontal Lines Appear or Screen
Normal
Normal
Abnormal
Abnormal
Check R304,R305D301,D302
CheckIC201S
Check IC201SPin 21,22
(VDN,VDP)
Check IC301 B+16V-C,-13.5V-C
Check / ReplaceIC301
![Page 27: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/27.jpg)
6. Exploded View & Parts List
6-1 CM27020SX/KMT
Exploded View & Parts List
Samsung Electronics 6-1
No Code No Description;Specification Q’ty Remark
1-1 AA64-02794A INLAY-CONTROL;26F7,PS SHEET,T0.5 1 INL/CT
1-2 AA64-02281A BADGE-BRAND;27V,AL FORGING,SILVER,C/MATH 1 BADGE
1-3 AA64-02788A CABINET-FRONT;29F7,HIPS,V0,BLK 1 F/C
1-4 AA65-30105A CLAMP-WIRE;NYLON 66N,VO,NTR,15MM 1 CWFC
1-5 AA61-40113A STOPPER-PCB;-,ABS,HB,NTR. 1 STOPPE
1-6 3001-001262 SPEAKER;3W,8OHM,87DB,280HZ 2 SPK
1-7 AA60-10008A SCREW-TAPPING;-,TH,+,M3,L10,ZP 4 SPK+CF
1-8 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR 7 CB+CF
1-9 AA64-02303A CABINET BACK;TROJAN 27V,HIPS,V0,BLK 1 C/B
1-10 AA96-20129C ASSY-POWER,CORD;-,EP2/YES,H/C200,ME301P, 1 PWR/AC
1-11 AA64-00144C INLAY-BACK;PS SHEET,29F6,T0.5,K15C S/T D 1 INLAYB
1-12 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR 1 CB+RCA
2 AA03-00147A CRT COLOR;-,A68QDN891X001,+380mG,29inch, 1 CRT
2-1 AA65-00019A CLAMP CORE-D,COIL;25-34,NYLON 66,V2,NTR 4 C/DCOI
2-2 AA60-10050V SCREW-ASSY;WC,HH,+,M6,L30,SWRCH18A,ZPC(S 4 CRT+CF
3 AA91-01660A ASSY CHASSIS;TXM2756X/XAA 1 A/CHAS
![Page 28: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/28.jpg)
Electrical Parts List
Samsung Electronics 7-1
7-1 CM27020SX/KMT
7. Electrical Parts List
Loc. No. Code No. Description ; Specification Remark
ASSY CHASSIS
1 A/CHAS AA91-01660A ASSY CHASSIS;TXM2756X/XAA 1
2 DRESFB AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL 12 ASSY,P AA94-07316A ASSY PCB MAIN;TXM2756X/XAA 13 0202-000008 SOLDER-WIRE;S63S-D3.0,S63A,D3,63/37 0.0543 0202-000187 SOLDER-WIREFLUX;-,RS60S,D1.2,6 0.0013 0204-000442 SOLVENT;CH3-CH5H-CH396%IM-1000 0.0073 0204-001024 FLUX;DF-96TVS,-,20%,- 0.0093 D807 0402-001375 DIODE-RECTIFIER;FFPF10U20S,200V,10A,TO-2 13 PC801S 0604-001032 PHOTO-COUPLER;TR,170-260%,300M 13 IC902 1103-001209 IC-EEPROM;AT24C04-PC27 C,512Kx8Bit,DIP,8 13 IC601 1201-001201 IC-POWER AMP;7268,DIP,16P,300MIL,DUAL,32 13 IC101 1204-000506 IC-LINEAR;LA7510SIP9P 13 NT801S 1404-001045 THERMISTOR NTC;4.7OHM,15%,2900K,35.0MW,T 13 PT802S 1404-001246 THERMISTOR-PTC;1.5OHM,+30/-20,110V,140VA 13 CY801S 2201-002002 C-CERAMIC,DISC;4700PF,20%,400V 13 CR410S 2301-001456 C-FILM,MPE-PPF;5.1nF,5%,1.6kV,TP,29x9x16 13 CX801S 2306-000318 C-FILM,MPPF;220NF,20%,250V,-,2 13 C801 2401-002251 C-ELECTROLYTIC;CE04W200V470M(2 13 SF101S 2904-001107 FILTER-SAW AV;45.75MHz,SIP5K,TP,12.6dB,N 13 SF102S 2904-001255 FILTER-SAWAV;M9261M45.75MHz,SIP5K,12.2dB 13 RL801S 3501-001040 RELAYPOWER;12VDC,500MW,10A,1FO 13 FP801S 3601-000281 FUSE-FERRULE; 250V,4A 13 V999S 3704-001105 SOCKET-CRT;11P,20PI,26.5PI,NI,- 13 CN601 3711-002643 POST-HEADER;YW025-04(AUTO) 13 JR701 3722-001744 JACK-PIN;8P(9P),-,NI,YEL/WHT/RED/GRN/BL 13 IC201S AA09-00272A IC-MICOM;TDA9377PS/N2/A,SPM-456AN1,64P,3 13 T801S AA26-00166A TRANS SWITCHING;EER3942,TROIJAN,120V,PM2 13 T444S AA26-00167A TRANS FBT;FQH-29A001(S),CT29D4,3.5MH,130 13 T401 AA26-50001M HORIZ.DRIVE;-,80MH,520UH,4UH,E 13 LR401S AA27-00035A COIL-LINEARLITY;-,30UH,DR15X18,0.8MM,19X 13 LX801S AA29-30002F FILTER-LINENOISE;-,6MH,2.45A,- 13 RM901 AA32-00014A MODULE REMOCON;346VF2,38KHZ,940MM,MESH,V 13 CN501 AA39-20620D LEAD CONNECTOR ASSY;CT29F6,UL1007#26,UL/ 13 TU01S AA40-00073A TUNER-TECC1040PG32A(S),181CH,45.75MHZ,75 13 L/PQS AA68-01018A LABEL-PQS,-,50mmX,13,-,WHITE,- 13 IC301 AA96-00244F ASSY H/S;-,VERTICAL,AA62-00046A,LA7841, 14 0205-000129 GREASE-SILICON;SC102,JAPAN 0.0094 1204-001807 IC-VERTICAL PROCESSO;LA7841,SIP,7P,708MI 14 6003-000335 SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR 14 H/SINK AA62-00046A HEAT SINK-PS;-,-,T1.0,-,D1(DREAM) 60X25X 13 IC802 AA96-00245A ASSY H/S;-,-,AA62-00055A,KA7632,- 14 1203-001939 IC-POSI.FIXED REG.;7632,SIP,10P,-,PLASTI 14 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZP 14 AA62-00055A HEAT SINK-PS;-,-,T1.0,-,35*15*25,D1,-,-, 13 IC801S AA96-00815A ASSY H/S;,POWER,AA62-00111A,5Q0740RT,TR 14 0205-000129 GREASE-SILICON;SC102,JAPAN 0.0094 1203-002466 IC-PWM CONTROLLER;KA5Q0740RT,TO220F-5L,5 14 6003-000335 SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR 14 AA62-00111A HEAT SINK;TROJAN,AL1050 ,T1.0,W54.0,H40. 13 Q401 AA96-00817A ASSY H/S;,HORIZONTAL,AA62-00113A,KSC580 14 0205-000129 GREASE-SILICON;SC102,JAPAN 0.0094 0502-001191 TR-POWER;KSC5802D,NPN,60000mW,TO-3P,ST, 14 6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW 14 AA60-30001A WASHER-PLATE;-,M3,ID3.5,15X8.5,T1.0,-,SB 14 AA62-00113A HEAT SINK;BH62-00041A,A1050S,T1.0,W23.0, 13 PWR/AC AA96-20129C ASSY-POWER,CORD;-,EP2/YES,H/C200,ME301P, 14 AA39-10007Y POWER-CORD;-,EP2/YES,SPT-2 18AWGx2C,2.4m 14 AA61-20284A HOLDER P CORD;PP,VO,BLK,KE-002 13 IC501 AA96-50311A ASSY-H/S;-,VIDEO,AA62-30175D,TDA6107Q,- 14 1201-001159 ICVIDEOAMP;TDA6107Q,ZIP,9P,300 14 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZP 14 AA62-30175D HEATSINK-PS;-,SECC,T1.0,-,33X15X30FT-2 13 ASSY,A AA97-06319A ASSY AUTO;TXM2756X/XAA 14 D201 0401-000005 DIODE;1N4148,100V,300mA,1V,8nS,TAPING 1
4 D803 0401-000005 DIODE;1N4148,100V,300mA,1V,8nS,TAPING 14 D804 0401-000005 DIODE;1N4148,100V,300mA,1V,8nS,TAPING 14 D808 0401-000005 DIODE;1N4148,100V,300mA,1V,8nS,TAPING 14 D811 0401-000005 DIODE;1N4148,100V,300mA,1V,8nS,TAPING 14 DR003S 0401-000005 DIODE;1N4148,100V,300mA,1V,8nS,TAPING 14 D501 0402-000254 DIODE-RECTIFIER;RGP10J,600V,1A,DO-41 14 D401 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1 14 D301 0402-000534 DIODE-RECTIFIER;RG10V,400V,1.5 14 D302 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5 14 D805 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5 14 D304 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1. 14 DR001S 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1. 14 D502 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40 14 D503 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40 14 D504 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40 14 D812 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40 14 D801S 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-2 14 D802S 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-2 14 D803S 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-2 14 D804S 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-2 14 D303 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 14 D809 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 14 D902 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 14 DZ105 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 14 DZ211 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 14 DZ401 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 14 DZ806 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 14 DZ811 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 14 DZ904 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 14 DZ905 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 14 DZ101 0403-000700 DIODE-ZENER;TZP33A,33V,31-35V, 14 DZ303 0403-000700 DIODE-ZENER;TZP33A,33V,31-35V, 14 DR002S 0403-000718 DIODE-ZENER;MTZJ6.8B,6.8V,6.49-6.83V,500 14 DZ201 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ204 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ205 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ208 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ209 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ210 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ306 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ307 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ501 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ502 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ503 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ504 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ808 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 14 DZ801 0403-001140 DIODE-ZENER;RD10ESAB-T4,10V,9.19-10.30V, 14 DZ310 0403-001221 DIODE-ZENER;UZ39BSB,35.36-37.19V,500MW,D 14 DZ802 0403-001318 DIODE-ZENER;MTZJ4.3B,4.17-4.43V,500mW,DO 14 DZ805 0403-001327 DIODE-ZENER;MTZJ18A,16.22-17.06V,500mW,D 14 DZ301 0403-001328 DIODE-ZENER;MTZJ22A,20.15-21.20V,500mW,D 14 DZ305 0403-001328 DIODE-ZENER;MTZJ22A,20.15-21.20V,500mW,D 14 DZ302 0403-001329 DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW, 14 Q201 0501-000283 TRANSISTOR;KSA539-Y(TAPG)/YTAM 14 QR001S 0501-000283 TRANSISTOR;KSA539-Y(TAPG)/YTAM 14 Q402 0501-000369 TRANSISTOR;KSC2331-Y(TAPG) 14 Q951 0501-000369 TRANSISTOR;KSC2331-Y(TAPG) 14 Q202 0501-000389 TRANSISTOR;KSC815-Y(TAPG)/YTAM 14 Q603 0501-000389 TRANSISTOR;KSC815-Y(TAPG)/YTAM 14 Q802 0501-000389 TRANSISTOR;KSC815-Y(TAPG)/YTAM 14 IC803 1203-001217 IC-POST,ADJUSTREG;431,T0-92,3P,4.58MIL,P 14 R207 2001-000005 R-CARBON;390OHM,5%,1/8W,AA,TP, 14 R905 2001-000005 R-CARBON;390OHM,5%,1/8W,AA,TP, 14 R906 2001-000005 R-CARBON;390OHM,5%,1/8W,AA,TP, 14 RR002S 2001-000009 R-CARBON;20KOHM,5%,1/8W,AA,TP, 14 R206 2001-000010 R-CARBON;68Kohm,5%,1/8W,AA,TP,1.8x3.2mm 14 R301 2001-000016 R-CARBON(S);1OHM,5%,1/2W,AA,TP 14 R409 2001-000020 R-CARBON(S);22OHM,5%,1/2W,AA,T 1
Loc. No. Code No. Description ; Specification Remark
![Page 29: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/29.jpg)
4 R808 2001-000109 R-CARBON(S);470OHM,5%,1/2W,AA, 14 R816 2001-000117 R-CARBON(S);68ohm,5%,1/2W,AA,TP,2.4x6.4m 14 R902 2001-000241 R-CARBON;1.5KOHM,5%,1/8W,AA,TP 14 R904 2001-000241 R-CARBON;1.5KOHM,5%,1/8W,AA,TP 14 R620 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP 14 R621 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP 14 R107 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R211 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R223 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R501 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R502 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R506 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R510 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R511 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R512 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R911 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R912 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R913 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R914 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R917 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R933 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R934 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R942 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R943 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 R224 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 14 R230 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 14 R828 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 14 R833 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 14 R835 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 14 R842 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 14 R915 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 14 R918 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 14 R225 2001-000325 R-CARBON;120OHM,5%,1/8W,AA,TP, 14 R205 2001-000397 R-CARBON;180KOHM,5%,1/8W,AA,TP 14 R229 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 14 R619 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 14 R919 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 14 R926 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 14 R231 2001-000435 R-CARBON;1MOHM,5%,1/8W,AA,TP,1 14 R232 2001-000435 R-CARBON;1MOHM,5%,1/8W,AA,TP,1 14 R940 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP 14 R941 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP 14 R220 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP 14 R901 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP 14 R903 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP 14 R907 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP 14 R908 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP 14 R214 2001-000490 R-CARBON;200OHM,5%,1/8W,AA,TP, 14 R218 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP, 14 R101 2001-000554 R-CARBON;270OHM,5%,1/8W,AA,TP, 14 R102 2001-000554 R-CARBON;270OHM,5%,1/8W,AA,TP, 14 R829 2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM 14 R208 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP 14 R202 2001-000645 R-CARBON;330KOHM,5%,1/8W,AA,TP 14 RR001S 2001-000660 R-CARBON;33KOHM,5%,1/8W,AA,TP, 14 R830 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP 14 R925 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP 14 R227 2001-000739 R-CARBON;4.7MOHM,5%,1/8W,AA,TP 14 R228 2001-000739 R-CARBON;4.7MOHM,5%,1/8W,AA,TP 14 R701 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm 14 R702 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm 14 R109 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP, 14 R927 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1 14 R203 2001-000857 R-CARBON;560OHM,5%,1/8W,AA,TP, 14 R602 2001-000890 R-CARBON;6.8KOHM,5%,1/8W,AA,TP 14 R603 2001-000890 R-CARBON;6.8KOHM,5%,1/8W,AA,TP 14 R604 2001-000890 R-CARBON;6.8KOHM,5%,1/8W,AA,TP 14 R607 2001-000890 R-CARBON;6.8KOHM,5%,1/8W,AA,TP 14 R110 2001-000924 R-CARBON;680ohm,5%,1/8W,AA,TP,1.8x3.2mm 14 R105 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP 14 R222 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP 14 R210 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1 14 R212 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1 14 R711 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1 14 R712 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1 14 R714 2001-000969 R-CARBON;75OHM,5%,1/8W,AA,TP,1 14 R707 2001-001035 R-CARBON ;91ohm,5%,1/8W,AA,TP,1.8x3.2mm 1
4 R504 2001-001062 R-CARBON(S);10MOHM,5%,1/2W,AA, 14 R414 2001-001078 R-CARBON(S);15KOHM,5%,1/2W,AA, 14 R840 2001-001078 R-CARBON(S);15KOHM,5%,1/2W,AA, 14 R819 2001-001088 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4 14 R820 2001-001088 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4 14 R832 2001-001088 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4 14 R411 2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA, 14 RR003S 2001-001128 R-CARBON(S);30KOHM,5%,1/2W,AA, 14 R821 2001-001131 R-CARBON(S);33KOHM,5%,1/2W,AA, 14 R818 2001-001154 R-CARBON(S);5.1KOHM,5%,1/2W,AB 14 R805 2001-001170 R-CARBON(S);6.8OHM,5%,1/2W,AB, 14 R850 2001-001170 R-CARBON(S);6.8OHM,5%,1/2W,AB, 14 R831 2001-001192 R-CARBON(S);820OHM,5%,1/2W,AB, 14 R823 2001-001199 R-CARBON(S);91OHM,5%,1/2W,AA,T 14 R501H 2002-001009 R-COMPOSITION;2.7KOHM,10%,1/2W,AA,TP,3.7 14 R502H 2002-001009 R-COMPOSITION;2.7KOHM,10%,1/2W,AA,TP,3.7 14 R503 2002-001009 R-COMPOSITION;2.7KOHM,10%,1/2W,AA,TP,3.7 14 RP801S 2002-001010 R-COMPOSITION;1.8MOHM,5%,1/2W,AA,TP,3.7X 14 RY801S 2002-001012 R-COMPOSITION;8.2MOhm,5%,1/2W,AA,TP,3.7X 14 R402 2003-000540 R-METALOXIDE(S);1KOHM,5%,2W,AD 14 R407 2003-000586 R-METALOXIDE(S);22KOHM,5%,2W,A 14 R410 2003-000586 R-METALOXIDE(S);22KOHM,5%,2W,A 14 R413 2003-000664 R-METAL OXIDE(S);330HM,5%,2W,AF,TP,4X12M 14 R802 2003-000664 R-METAL OXIDE(S);330HM,5%,2W,AF,TP,4X12M 14 R803 2003-000994 R-METALOXIDE(S);33KOHM,5%,2W,AF,TP,3.9X1 14 R827 2003-002009 R-METALOXIDE(S);390OHM,5%,2W,A 14 R834 2003-001040 R-METALOXIDE(S);47Kohm,5%,2W,AF,TP,3.9x1 14 R315 2003-002009 R-METALOXIDE(S);390OHM,5%,2W,A 14 R317 2003-002009 R-METALOXIDE(S);390OHM,5%,2W,A 14 R403 2003-002151 R-METALOXIDE;18KOHM,5%,2W,AG,TP,6X16 14 R302 2004-001371 R-METAL(S);1.5KOHM,1%,1/2W,AA, 14 R306 2004-001371 R-METAL(S);1.5KOHM,1%,1/2W,AA, 14 R424 2004-001402 R-METAL(S);6.8KOHM,1%,1/2W,AA, 14 R817 2004-001889 R-METAL(S);127KOHM,1%,1/2W,AA,TP,2.5X6.5 14 R219 2004-001914 R-METAL;39KOHM,2%,1/8W,AA,TP,1 14 R822 2004-001983 R-METAL;2.49KOHM,1%,1/2W,AA,TP,2.4X6.4 14 RR004S 2004-004015 R-METAL(S);9.1KOHM,1%,1/2W,AA, 14 R423 2004-005045 R-METAL;75KOHM,1%,1/2W,AA,TP,2.4X6.4MM 14 R825 2008-000266 R-FUSIBLE(S);1OHM,5%,2W,AF,TP, 14 R824 2008-000294 R-FUSIBLE;33OHM,5%,2W,AF,TP,3. 14 R425 2008-000299 R-FUSIBLE;RF2RT470-J 14 R304 2008-001011 R-FUSIBLE(S);0.18OHM,10%,2W,AF 14 R305 2008-001011 R-FUSIBLE(S);0.18OHM,10%,2W,AF 14 R307 2008-001013 R-FUSIBLE(S);1.2ohm,5%,2W,AF,TP,3.9x10mm 14 R303 2008-001015 R-FUSIBLE;1.50HM,5%2WAF,TP39X10 14 R505 2008-001015 R-FUSIBLE;1.50HM,5%2WAF,TP39X10 14 R610 2008-001076 R-FUSIBLE(S);1.8ohm,5%,2W,AF,TP,3.9x10mm 14 R612 2008-001076 R-FUSIBLE(S);1.8ohm,5%,2W,AF,TP,3.9x10mm 14 R421 2008-001076 R-FUSIBLE(S);1.8ohm,5%,2W,AF,TP,3.9x10mm 14 R422 2008-001076 R-FUSIBLE(S);1.8ohm,5%,2W,AF,TP,3.9x10mm 14 R316 2008-001107 R-FUSIBLE(S);300ohm,5%,2W,AG,TP,3.9x12mm 14 C806A 2201-000108 C-CERAMIC,DISC;1.5NF,10%,1KV,Y 14 C402 2201-000132 C-CERAMIC,DISC;100PF,10%,500V,Y5P,6X3MM, 14 C501 2201-000192 C-CERAMIC,DISC;10PF,0.25PF,500V,NPO,-,5M 14 C302 2201-000259 C-CERAMIC,DISC;180PF,10%,500V,Y5P,6X4MM, 14 C906 2201-000292 C-CERAMIC,DISC;1NF,10%,50V,Y5P 14 C816 2201-000375 C-CERAMIC,DISC;220PF,5%,50V,RH 14 C908 2201-000573 C-CERAMIC,DISC;47PF,5%,50V,NPO 14 C909 2201-000573 C-CERAMIC,DISC;47PF,5%,50V,NPO 14 C408 2201-000599 C-CERAMIC,DISC;560PF,10%,500V, 14 C811 2201-000599 C-CERAMIC,DISC;560PF,10%,500V, 14 CR404S 2201-000639 C-CERAMIC,DISC;680PF,10%,2KV,Y5P,-,5MM,T 14 C503 2201-000723 C-CERAMIC,DISC;4.7nF,20%,3KV,Y5U,TP,16x5 14 C602 2201-000982 C-CERAMIC,DISC;10NF,+80-20%,50 14 C105 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 14 C106 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 14 C111 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 14 C121 2202-000286 C-CERAMIC,MLC-AXIAL;56PF,5%,50 14 C211 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP 14 C223 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50 14 C224 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50 14 C226 2202-000829 C-CERAMIC,MLC-AXIAL;820pF,10%,50V,Y5P,TP 14 C604 2301-000192 C-FILM,PEF;1NF,5%,50V,5.3X10MM 14 C609 2301-000192 C-FILM,PEF;1NF,5%,50V,5.3X10MM 14 C502 2301-000213 C-FILM,PEF;220NF,5%,250V,21.5X 14 C109 2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9 14 C804 2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9 1
Electrical Parts List
7-2 Samsung Electronics
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
![Page 30: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/30.jpg)
4 C810 2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9 14 C613 2301-000232 C-FILM,PEF;3.3NF,5%,50V,8.1X4. 14 C614 2301-000232 C-FILM,PEF;3.3NF,5%,50V,8.1X4. 14 C805 2301-000235 C-FILM,PEF;3.9NF,5%,50V,6.5X3.0X5.5MM,5M 14 C309 2301-000254 C-FILM,PEF;39NF,5%,50V,7.5X3.5X6.5MM,5MM 14 C217 2301-000342 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm, 14 C407 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm 14 C227 2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm 14 C248 2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm 14 C420 2301-001065 C-FILM,MPPF;47NF,55,630V,TP,19 14 CR403S 2301-001301 C-FILM,MPPF;440NF,5%,250V,TP,19X8.5X16MM 14 C312 2305-000149 C-FILM;CF922N100VT104-J-40/105 14 C301 2305-000285 C-FILM,MPEF;220NF,5%,100V,-,5M 14 C205 2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM 14 C215 2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM 14 C216 2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM 14 C233 2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM 14 C234 2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM 14 C235 2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM 14 C236 2305-000289 C-FILM,MPEF;220NF,5%,63V,-,5MM 14 CR405S 2305-000382 C-FILM,MPEF;4.7NF,5%,400V,TP,-,5MM. 14 C207 2305-000412 C-FILM,MPEF;470NF,5%,63V,-,5MM 14 C911 2305-000412 C-FILM,MPEF;470NF,5%,63V,-,5MM 14 C103 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C208 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C210 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C218 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C230 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C803 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C819 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C913 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C916 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C920 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 C225 2309-000138 C-FILM,PE-PPF;100NF,5%,50V,TP, 14 C228 2401-000027 C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA 14 C611 2401-000027 C-AL;4.7UF,20%,50V,GP,5*11MM,5MEA 14 C827 2401-000040 C-ALUMINUM;47UF,20%,250V,WT16*25MM,7EA 14 C222 2401-000215 C-AL;100NF,20%,50V,4X7MM,5MM,T 14 C812 2401-000262 C-AL;100UF,20%,160V,GP,16X25MM,5MM, 14 C821 2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5 14 C823 2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5 14 C915 2401-000302 C-AL;100UF,20%,25V,GP,6X11MM,5 14 C307 2401-000365 C-AL;100uF,20%,50V,WT,TP,10x12.5mm, 14 C308 2401-000365 C-AL;100uF,20%,50V,WT,TP,10x12.5mm, 14 C506 2401-000430 C-ELECTROLYTIC;CE04WTAPG250V10 14 C104 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 14 C203 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 14 C650 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 14 C651 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 14 C820 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 14 CR01S 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 14 CR02S 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 14 C219 2401-000603 C-AL;1UF,20%,50V,GP,5X11MM,5MM 14 C221 2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2 14 C601 2401-000703 C-ELEC;CE04-40/8525VT222-MWSD 14 C815 2401-000703 C-ELEC;CE04-40/8525VT222-MWSD 14 C110 2401-000914 C-AL;22UF,20%,16V,GP,5X11,5,TP 14 C802 2401-001192 C-AL;33UF,20%,50V,GP,6X11MM,5MM,TP 14 C504 2401-001232 C-AL;4.7UF,20%,250V,GP,10X12.5 14 C119 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4 14 C120 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4 14 C702 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4 14 C703 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4 14 C607 2401-001397 C-AL;470UF,20%,25V,GP,10X16MM, 14 C608 2401-001397 C-AL;470UF,20%,25V,GP,10X16MM, 14 C901 2401-001537 C-AL;47UF,20%,25V,GP,6.3X7MM,5 14 C113 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1 14 C209 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1 14 C213 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1 14 C229 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1 14 C903 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1 14 C910 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1 14 C605 2401-001914 C-AL;1uF,20%,50V,BP,TP,5x11,5 14 C610 2401-001914 C-AL;1uF,20%,50V,BP,TP,5x11,5 14 C101 2401-002183 C-AL;220uF,20%,16V,GP,TP,8x9,5mm 14 C220 2401-002235 C-ELECTROLYTIC;CE04W(T)16V10M 14 C231 2401-002235 C-ELECTROLYTIC;CE04W(T)16V10M 1
4 C403 2401-002268 C-ELEC;CE04-40/105250VT2R2-MWR 14 C304 2401-002288 C-ELEC;CE04-55/10525VT471-MWRG 14 C306 2401-002288 C-ELEC;CE04-55/10525VT471-MWRG 14 C813 2401-002290 C-AL;47uF,20%,160V,GP,TP,13x20,5 14 C406 2401-002619 C-AL;47uF,20%,25V,GP,TP,5x11,5 14 C817 2401-003028 C-AL;100UF,20%,25V,WT,TP,6.3X1 14 C818 2401-003028 C-AL;100UF,20%,25V,WT,TP,6.3X1 14 L103 2701-000114 INDUCTOR-AXIAL;10UH,10%,2.5X3. 14 L104 2701-000114 INDUCTOR-AXIAL;10UH,10%,2.5X3. 14 L202 2701-000114 INDUCTOR-AXIAL;10UH,10%,2.5X3. 14 L203 2701-000127 INDUCTOR-AXIAL;15UH,10%,2.5X3. 14 J102 2701-000142 INDUCTOR-AXIAL;1UH,10%,2.5X3.4 14 J103 2701-000142 INDUCTOR-AXIAL;1UH,10%,2.5X3.4 14 L301 2701-000142 INDUCTOR-AXIAL;1UH,10%,2.5X3.4 14 L302 2701-000142 INDUCTOR-AXIAL;1UH,10%,2.5X3.4 14 L404 2701-000142 INDUCTOR-AXIAL;1UH,10%,2.5X3.4 14 L902 2701-000158 INDUCTOR-AXIAL;22UH,10%,2.5X3. 14 L903 2701-000158 INDUCTOR-AXIAL;22UH,10%,2.5X3. 14 L904 2701-000158 INDUCTOR-AXIAL;22UH,10%,2.5X3. 14 L205 2701-000159 INDUCTORAXIAL;22uH,10%,4.2x9.8mm 14 L303 2701-000159 INDUCTORAXIAL;22uH,10%,4.2x9.8mm 14 L304 2701-000159 INDUCTORAXIAL;22uH,10%,4.2x9.8mm 14 L804 2701-001030 INDUCTOR-AXIAL;43uH,10%,14x4.5mm 14 L102 2702-000142 INDUCTOR-RADIAL;22uH,5%,6x6.4mm 14 L201 2702-000142 INDUCTOR-RADIAL;22uH,5%,6x6.4mm 14 X901 2801-003433 CRYSTAL-UNIT;12MHZ,30PPM,28-AAM,30PF,30O 14 L402 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,- 14 L403 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,- 14 L806 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,- 14 L808 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,- 14 Z201 2903-000129 FILTER-CERAMIC;BR,4.5MHz,-,-,-,TP,- 14 L206 3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6. 14 L406 3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6. 14 L802 3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6. 14 L803 3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6. 14 R408 3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6. 14 SW901 3404-000244 SWITCH-TACT;15V,20MA,90-170GF, 14 SW902 3404-000244 SWITCH-TACT;15V,20MA,90-170GF, 14 SW903 3404-000244 SWITCH-TACT;15V,20MA,90-170GF, 14 SW904 3404-000244 SWITCH-TACT;15V,20MA,90-170GF, 14 SW905 3404-000244 SWITCH-TACT;15V,20MA,90-170GF, 14 SWN01 3404-000244 SWITCH-TACT;15V,20MA,90-170GF, 14 FD801S 3601-001086 FUSE-AXIAL LEAD;125V,5A,FAST-ACTING,GLAS 14 F801A 3602-000114 FUSE-HOLDER;-,-,30MOHM 14 F801B 3602-000114 FUSE-HOLDER;-,-,30MOHM 14 C507 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 C508 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 DZ804 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J101 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J104 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J105 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J106 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J107 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J108 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J109 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J125 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J129 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J131 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J150 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J157 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J173 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J175 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J201 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J203 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J204 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J205 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J208 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J209 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J210 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J211 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J212 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J213 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J214 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J216 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J218 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J305 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J307 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 1
Electrical Parts List
Samsung Electronics 7-3
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
![Page 31: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/31.jpg)
4 J308 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J312 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J402 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J405 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J407 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J408 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J409 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J420 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J423 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J601 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J602 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J603 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J604 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J607 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J608 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J705 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J706 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J711 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J715 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J716 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J717 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J721 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J802 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J803 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J805 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J806 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J807 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J808 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J809 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J810 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J812 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J813 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J816 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J817 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J818 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J820 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J821 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J823 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J901 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J902 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J903 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J904 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J905 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 JP02 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 JR001S 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 L702 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 L703 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 L704 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 R405 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 R507 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 R508 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 R509 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 R601 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J712 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J302 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 J303 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 PCB AA41-00572A PCB-MAIN;29F6,FR-1,1L,A,1.6T,245X245,K1 14 EY401 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY402 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY403 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY404 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY405 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY406 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY412 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY414 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY416 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY417 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY418 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY419 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY420 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY421 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY701 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY702 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY801 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY802 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY803 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 14 EY804 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST 1
4 EL403 AA60-40011B EYELET;-,ID2.2,OD3.2,-,-,BSP 14 EL801 AA60-40011B EYELET;-,ID2.2,OD3.2,-,-,BSP 14 EL802 AA60-40011B EYELET;-,ID2.2,OD3.2,-,-,BSP 14 GT403 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT502 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT801 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT802 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT803 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT804 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT805 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT301 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT302 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT401 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 GT402 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO 14 L/LINE AA68-01544A LABEL;LINE,ALL MDL COMMON 14 DZ903 0403-001373 DIODE-ZENER;MTZJ5.1A,4.81V-5.07V,500mW,D 14 DZ901 0403-001373 DIODE-ZENER;MTZJ5.1A,4.81V-5.07V,500mW,D 13 CR409S 2306-000328 C-FILM,MPPF;6.8nF,5%,1.6KV,TP,28.5x18x1 13 JR02 3722-001749 JACK-PIN;3P(3P),-,NI,YEL/WHT/RED,- 13 C505 2301-000108 C-FILM,PEF;1.5NF,5%,50V,6.5X3.0X5.5MM,5M 13 A/SOUN AA95-01591A ASSY SOUND;TROJAN,K15C,STEREO 14 ICS02 1203-000515 IC-VOL. DETECTOR;7042,TO-92,3P,177MIL,PL 14 ICS01 1204-001662 IC-SOUND PROCESSOR;MSP3425G-B7,DIP,52P,5 14 RS07 2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP, 14 RS08 2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP, 14 RS02 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 RS03 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 14 RS04 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 14 RS01 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 14 RS05 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 14 RS06 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 14 RS10 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm 14 RS11 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm 14 CS27 2201-000292 C-CERAMIC,DISC;1NF,10%,50V,Y5P 14 CS29 2201-000304 C-CERAMIC,DISC0.001nF,0.25pF,50V,NP0,TP 14 CS30 2201-000304 C-CERAMIC,DISC0.001nF,0.25pF,50V,NP0,TP 14 CS28 2202-000286 C-CERAMIC,MLC-AXIAL;56PF,5%,50 14 CS31 2202-000286 C-CERAMIC,MLC-AXIAL;56PF,5%,50 14 CS01 2301-000108 C-FILM,PEF;1.5NF,5%,50V,6.5X3.0X5.5MM,5M 14 CS15 2301-000108 C-FILM,PEF;1.5NF,5%,50V,6.5X3.0X5.5MM,5M 14 CS36 2301-000232 C-FILM,PEF;3.3NF,5%,50V,8.1X4. 14 CS37 2301-000232 C-FILM,PEF;3.3NF,5%,50V,8.1X4. 14 CS07 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm 14 CS17 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 CS23 2305-000665 C-FILM;104J, 60V,5MM TAPING 14 CS03 2401-000318 C-AL(105C);100UF,20%,25V,WT,8X 14 CS12 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 14 CS14 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 14 CS06 2401-001026 C-AL;3.3UF,20%,50V,GP,5X11MM,5 14 CS18 2401-001026 C-AL;3.3UF,20%,50V,GP,5X11MM,5 14 CS16 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1 14 CS25 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1 14 LS01 2701-000114 INDUCTOR-AXIAL;10UH,10%,2.5X3. 14 LS03 2701-000169 INDUCTORAXIAL;3.9uH,10%,2.5x3.4mm 14 LS04 2701-000169 INDUCTORAXIAL;3.9uH,10%,2.5x3.4mm 14 XS01 2801-000186 CRYSTAL-UNIT;18.432MHz,25ppm,28-AAM,8pF, 14 CNS02 3711-002706 PIN-HEADER;YFAW025-108(8PIN2.5M/M)20.0 14 CNS01 3711-002708 CONNECTOR-HEADER;NOWALL,10P,1R,2.5mm,ANG 14 JS05 3812-000219 JUMPER-WIRE-SO,COPPER;TA0.6SN/52M/M(A 14 PCB AA41-00573A PCB-STEREO MODULE;29F6,FR-1,1L,A,1.6T,33 14 CNS03 AA61-10068A BRACKET-PCB;-,SPTE,-,T0.3,-,-, 1
ASSY COVER REAR
1 A/REAR AA90-03597A ASSY COVER REAR;K15C,29F7,KMT 1
2 CB+CF 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR 72 CB+RCA 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR 12 C/B AA64-02303A CABINET BACK;TROJAN 27V,HIPS,V0,BLK 12 AC+BC AA65-30008A CLAMP-CORD;-,PE,HB,BLK,-,- 1
Electrical Parts List
7-4 Samsung Electronics
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
![Page 32: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/32.jpg)
ASSY COVER FRONT
1 A/CFRN AA90-03596A ASSY COVER FRONT;K15C,29F7,V0,KMT 1
2 SPK 3001-001262 SPEAKER;3W,8OHM,87DB,280HZ 22 L/SPK AA39-20505M LEAD-CONNECTOR;SY4XREC,R700/L350 12 SPK+CF AA60-10008A SCREW-TAPPING;-,TH,+,M3,L10,ZP 42 CRT+CF AA60-10050V SCREW-ASSY;WC,HH,+,M6,L30,SWRCH18A,ZPC(S 42 STOPPE AA61-40113A STOPPER-PCB;-,ABS,HB,NTR. 12 F/C AA64-02788A CABINET-FRONT;29F7,HIPS,V0,BLK 13 INL/CT AA64-02794A INLAY-CONTROL;26F7,PS SHEET,T0.5 12 BADGE AA64-02281A BADGE-BRAND;27V,AL FORGING,SILVER,C/MATH 12 DRESPK AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL 22 CLM/CN AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL 12 CWFC AA65-30105A CLAMP-WIRE;NYLON 66N,VO,NTR,15MM 12 L/QMS AA68-02391A LABEL-QMS;ART-PAPER(90)G,110x24mm 1
ASSY LABEL
1 A/LABE AA92-06263A ASSY LABEL;K15C,KMT 1
2 L/RAT AA68-02484A LABEL-RATING;K-MART,ART PAPER;60X90MM,K1 12 INLAYB AA64-00144C INLAY-BACK;PS SHEET,29F6,T0.5,K15C S/T D 12 L/SET AA68-50394Q LABEL-D.H.H.S;SAM25405C/XAA,A/P120(G),-, 1
ASSY BOX
1 A/BOX AA92-06264A ASSY BOX;K15C,29F7,KMT 1
2 L/BOX AA68-01542A LABEL;(UNIBOX),PAPER WHT ALLMD 12 PCK AA69-01837A PACKING-CASE;29F7,CB D-2 BB 1.01
ASSY P/MATERIAL
1 A/PACK AA92-06265A ASSY P/MATERIAL;K15C,29F7,KMT 1
2 BXTAPE 0203-001295 TAPE-OPP MASKING;1242,T0.06,W100,L91.4M, 0.0022 STAPLE AA60-40006A PIN-STAPLE;-,-,-,H18,33X17.8X2 122 PE-BAG AA69-01209A BAG;SHEET,25-27,W54,L60,FOAM,OEM. 12 C/SET AA69-01681A CUSHION-SET;29F7,PS FOAMED,C=0.02 1
ASSY CPT
1 A/CPT AA91-01626A ASSY CPT;TXM2756X/XAA 1
2 CRT AA03-00147A CRT COLOR;-,A68QDN891X001,+380mG,29inch, 12 D-COIL AA27-00208A COIL DEGAUSSING;-,27V,2.8MH,10%,30T,1.5? 12 L/DY AA39-20568A LEAD CONNECTOR ASSY;YFHS06-06,S,6(4)P 12 C/DCOI AA65-00019A CLAMP CORE-D,COIL;25-34,NYLON 66,V2,NTR 42 A/TBC AA98-70002E ASSY TBC WIRE(P);-,29INCH,NTSC,1P,29F6(T 12 T/CRT 0203-001303 TAPE-ACETATE;#1554,T0.25,W19,L30000,WHT 0.3
ASSY ACCESSORY
1 A/ACCE AA92-06262A ASSY ACCESSORY;K15C,29F7,KMT 1
2 BAG-PE AA69-01195A BAG PE;CL29A6W8X,HDPET0.012,93/4X151 12 I/B1 AA68-02483A MANUAL-USERS;CM25020S/KMT(ENG);K15C 12 RMT AA59-00141G REMOCON;,TM58,SSM174PT,41,SS,G6671B,MBR, 12 BATT 4301-000120 BATTERY-MN;1.5V,-,AA 2
Electrical Parts List
Samsung Electronics 7-5
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
![Page 33: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/33.jpg)
7-6 Samsung Electronics
MEMO
![Page 34: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/34.jpg)
8. Block Diagram
8-1 K15C
Block Diagram
8-1
T U NE R -F /SUVS815KA-AMP
V I F SA WM3953M
A V I N PU T
A V O U T
V E R T IC ALA M P
LA7841CRT
5V T O TUN ER
R G B A M PT D A 6107
E 2P R OM24C04
A C KA5Q0740RT(KA5Q0765RT)
S / W MULTIREGULATOR
3.3V TO M CU
8V TO M CU
I 2C
AUDIO A M PTDA7268
F
SOUND PROCESSOR MSP3425G
BT ( 21"F,2 5",29")FQH-29A001(S)
V IDE O
I 2C
V IDE O
SI F SA WM9261M
LA7510
IC -M C US P M -4 5 6A N
2 3 2 421/ 22
50- 53
2 - 345 - 48 38
42
2
41,42
30,31
R/L OUT (24, 25)
STEREO
12
S/ W 2
1
R /G / B /FB
H -O UTT R
3 3
16.5V TO Ver . A M P180V TO C RT
Heat TO C RT
13V TO SOU NDAM P
8R * 2E A
±
KA7632
KSC 5802
(Option)
Q
![Page 35: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/35.jpg)
Samsung Electronics 9-1
9. Wiring Diagram
9-1 K15C
Wiring Diagram
CRT
PCB
87
65
43
12
SOUND L INSOUND R IN
SOUND L OUTSOUND R OUT
VIDEO INGND
VIDEO OUTGND
12
34
R- OUT
B- OUTG- OUT
GND
98
57
6 GNDIK
GNDHEAT
B+ OUT
CN50
1
CN60
1CN
701
43
21 R- OUT
L- OUTR+ OUT
L+ OUT
POW
ERCO
RD
![Page 36: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/36.jpg)
9-2
MEMO
![Page 37: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/37.jpg)
TP01 TP02
TP03
TP04
TP05
TP06
TP12
TP10
TP11
TP08
TP09
TP07
Schematic Diagrams
10-1Samsung Electronics
10. Schematic Diagrams10-1 MAIN (1/4)
: Power Line: Signal Line
TP01 TP02
TP04
TP05
TP07 TP08
TP10
TP11
TP03
TP06
TP09
TP12
![Page 38: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/38.jpg)
Schematic Diagrams
10-2 Samsung Electronics
10-2 MAIN (2/4)
TP01
TP02
TP04
TP03
TP05
TP01
TP02
: Power Line: Signal Line
TP03
TP04
TP05
![Page 39: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/39.jpg)
Schematic Diagrams
10-3Samsung Electronics
10-3 MAIN (3/4)
IN_
P U T 2O U T _P U T 2
CONT-ROLINPUTVCC GND NC NC
TP02
TP01
TP01
TP02
: Power Line: Signal Line
![Page 40: Samsung Crt Cm27020s](https://reader031.vdocuments.us/reader031/viewer/2022012309/563dbb0a550346aa9aa9c22c/html5/thumbnails/40.jpg)
Schematic Diagrams
10-4 Samsung Electronics
10-4 MAIN (4/4)