rt1025 ecg/ppg afe cardioid evaluation board · the rt1025 is an integrated afe solution for...
TRANSCRIPT
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 1 http://www.richtek.com
your power partner.
RT1025 ECG/PPG AFE Cardioid Evaluation Board
Purpose
The RT1025 is an integrated AFE solution for Heart-Rate monitoring and Biopotential measurements. The RT1025
integrates low noise voltage and current sensing channels and is capable of sensing ECG (Electrocardiography) and
PPG (Photoplethysmography) simultaneously. Richtek Technology developed an evaluation board with Android APP
to evaluate the RT1025 performance. This document describes the operation manual of the RT1025 evaluation board.
It includes the schematic, hardware and bench measure procedure.
Table of Contents
Purpose ................................................................................................................................................................. 1
Introduction ............................................................................................................................................................ 2
Key Performance Summary Table .......................................................................................................................... 3
Bench Test Setup Conditions ................................................................................................................................. 4
Schematic, Bill of Materials & Board Layout ......................................................................................................... 10
More Information.................................................................................................................................................. 15
Important Notice for Richtek Evaluation Board ..................................................................................................... 15
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 2 http://www.richtek.com
your power partner.
Introduction
General Product Information
The RT1025 is an integrated AFE solution for Heart-Rate monitoring and measurements. The RT1025 integrates low
noise voltage and current sensing channels and is capable of sensing ECG (Electrocardiography) and PPG
(Photoplethysmography) simultaneously. The RT1025 has > 100dB dynamic range and can sense pulses accurately
by detecting the heart’s electric signals. The sampling rates of the high-precision voltage and current sensing
channels in the RT1025 are configurable between 64 to 4kHz. The RT1025 solution need only few discrete
components and is easy to use for low-power medical ECG/PPG, sports, and fitness applications. With high levels
of integration and high-precision voltage and current sensing channels, the RT1025 solution is suitable for scalable
medical instrumentation systems. The RT1025 is available in a 3.1mm x 3.4mm, 41-Ball, 0.4mm pitch, WL-CSP
package.
The Cardioid evaluation board (Cardioid Pad) was developed full function Android APP to evaluate the RT1025
performance. The evaluation board includes the RT1025 together with the BLE SiP and PPG modules to quickly
evaluate the operation and performance of the RT1025. The detail schematic, hardware and bench measure
procedure will be described in the following section. The evaluation board number is PCB106_V1 and the dimensions
are 9cm x 5cm.
Product Feature
Evaluation Board Features
Evaluation Board Number : PCB106_V1
Dimension : 9cm x 5cm
ECG Channel Feature
3 PCB ECG Electrodes
Ear phone Jack for 3 ECG Electrodes
Low Input-Referred Noise : 0.67µVrms (64Hz ODR, Gain = 12)
Dynamic Range : 110dB at Gain = 6
CMRR > 85dB at 60Hz
Data rate : 64SPS to 4k SPS
PPG Channel Features
G/Red/IR LED with PD Module
Boost Supply for Green LED
TX LED Current Range : 10 / 25 / 35 / 50 / 65 / 75 / 90 / 105mA, Each with 8-bit Current Resolution
Input-Referred Noise : 50pArms at 5µA Input Current
CMRR > 80dB at 60Hz
PGA Gain : 1 to 6V/V
Others
Connect with “Cardio EVK” Android APP
Programmable BLE SiP
I2C interface for display panel
USB Micro-B interface for Lithium-Ion Battery Charging
Operating Temperature Range : –20°C to 65°C
RoHS Compliant and Pb Free
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 3 http://www.richtek.com
your power partner.
Key Performance Summary Table
Key Features Evaluation Board Number : PCB106_V1
PCB Battery Supply Voltage 3.6V (LIR2430)
PCB Battery Charging Voltage 5V via Micro USB connector
Current Consumption (Idle) 136µA
Current Consumption (BLE Advertising) 220µA
Current Consumption (BLE Connecting) 350µA
Current Consumption (Measuring) 8mA to 19mA (Depend on PPG measuring current setting)
Default Marking & Package Type RT1025WS, WL-CSP-41B 3.10x3.48 (BS)
* Note that EVB_RT1025WS_P0 kit does not include LIR2430 battery due to transport regulations.
* LIR2430 is a rechargeable Lithium Coin Cell 3.6V, capacity 80mAh.
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 4 http://www.richtek.com
your power partner.
Bench Test Setup Conditions
Headers Description and Placement
Carefully inspect all the components used in the EVB according to the following Bill of Materials table, and
then make sure all the components are undamaged and correctly installed. If there is any missing or
damaged component, which may have occurred during transportation, please contact our distributors or e-
mail us at [email protected].
Test Points
The EVB is provided with the connecter interfaces and pin names listed in the table below.
Test point/
Pin name Signal Comment (expected waveforms or voltage levels on test points)
VRLD Output voltage ECG RLD output.
FR / FL ECG Input Fingers contact for differential ECG input.
JP2 OLED Display
Interface (Option for display development)
JP2-1 DVDD33 Display supply voltage 3.3V.
JP2-2 DGND Display ground.
JP2-3 G_SCL Display I2C data pin.
JP2-4 G_SDA Display I2C clock pin.
JP4 EVB Interface Cardioid evaluation board Interface.
JP4-1 DVDD_SYS MCU supply voltage 3.3V.
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 5 http://www.richtek.com
your power partner.
Test point/
Pin name Signal Comment (expected waveforms or voltage levels on test points)
JP4-2 VPPG0_EN PPG R/IR LED select.
JP4-3 EXT_Control Bypass MCU on EVB (High : Bypass, Floating : Default)
JP4-4 VPPG1_EN PPG R/IR LED select.
JP4-5 E_RSTB RT1025 ECG/PPG AFE RSTB.
JP4-6 VBST_EN PPG Gn LED select.
JP4-7 E_PWD RT1025 ECG/PPG AFE RWD.
JP4-8 LDO_EN RT5707 DVDD18 enable.
JP4-9 E_INT RT1025 ECG/PPG AFE INT.
JP4-10 CHG_N RT9527 Charger CHG_N.
JP4-11 E_CSN RT1025 ECG/PPG AFE SPI data pin.
JP4-12 G_INT2 RT3001 G-sensor INT2.
JP4-13 E_CLK RT1025 ECG/PPG AFE SPI clock pin.
JP4-14 G_INT RT3001 G-sensor INT1.
JP4-15 E_MOSI RT1025 ECG/PPG AFE SPI serial in master out.
JP4-16 G_SDA RT3001 G-sensor I2C data pin.
JP4-17 E_MISO RT1025 ECG/PPG AFE SPI serial out master in.
JP4-18 G_SCL RT3001 G-sensor I2C clock pin.
JP4-19 DGND Ground.
JP4-20 DGND Ground.
CON5 ECG Input JACK Phone input for ECG patch.
CON5-1 VRLD_CON ECG RLD output.
CON5-2,
CON5-5 NC No internal connection.
CON5-3 FR ECG right signal input.
CON5-4 FL ECG left signal input.
SWD_B SWD debug pins MCU SWD debug pins.
SWD_B-1 DVDD33 MCU power pin 3.3V.
SWD_B-2 SWDIO MCU SWD IO pins.
SWD_B-3 SWCLK MCU SWD clock pins.
SWD_B-4 RESETN MCU SWD reset pins.
SWD_B-5 DGND Ground.
USB3 USB Charger Interface USB Micro-B for charger interface.
USB3-1 VBUS RT9527 charger IC input.
USB3-2 D- No internal connection.
USB3-3 D+ No internal connection.
USB3-4 ID No internal connection.
USB3-5 GND Ground.
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 6 http://www.richtek.com
your power partner.
Measurement Procedure
The RT1025 supports the reading of samples and device status upon interrupt or via polling. It contains 4kB SRAM
for data buffering. The device is internally clocked to offer high-precision clock with external crystal. The flexible timing
control enable the users to control the PPG device timing for different application and to power down the device for
power saving. In order to achieve the high speed data acquisition, the RT1025 device was configured as a slave of
SPI mode. The Cardioid evaluation board is fully assembled and tested. The usage of the evaluation board was
shown in below figure.
1. Insert LIR2430 Battery in the battery case. The battery can be charged by applying 5V via the Micro USB port.
Once on, you should see a Red LED lighting for OK status
If no light is present, check connections or try replacing the Battery with a fresh one.
If Red LED is flashing, check the I2C or SPI device correct connections.
2. Make sure the evaluation board connect to the Android APP for ECG/PPG measurement
Make sure Bluetooth is enabled on the phone/tablet.
Launch the “Cardio EVK” application on your phone/tablet.
Then, you will need to connect to the Cardioid evaluation board Hardware. Do this by selecting the “BLE ICON”
that shows up upon opening the android application. Select the evaluation board ID (RTK_CARDIO_00XXXX)
from pup-out menu for BLE paring.
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 7 http://www.richtek.com
your power partner.
After the Cardioid evaluation board BLE connection is successfully established, the “BLE ICON” will become
blue and the main GUI will launch.
3. Put your fingers cover the VRLD and PPG sensor in the top, FR/FL in the bottom.
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 8 http://www.richtek.com
your power partner.
4. Select “PPG+ECG“ tab firstly, then press “Measure” to start PPG+ECG data acquisitions. Note that it may take
a while to get stable results. Press “Stop”, once you finish the measurement.
5. Check the measurement results. Press “SAVE” to store the measured data for analysis.
Please refer to the document APP_RT1025WS_P0-00_EN for more information about the Android APP.
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 9 http://www.richtek.com
your power partner.
Typical Application Circuit
Using Cardioid evaluation board for ECG/PPG Sensing
RT1025
GND_D
AVDD28
AVDD_HV
GND_HV
VRLD
INP_ECGECGElectrode
INN_ECG
INP_PPG
INN_PPG
TX1
TX2
GND_A
DVDDIO
DVDD18
2.8V
2.8V
3.3V
1.8V
XTALI
RESETBRESETB
AFE_PWDAFE_PWD
I2C / SPI SPI
INTINT
BLE
SiP
2.2uF
2.2uF
2.2uF
1uF VBG
2.2uF
VRLD
VLX
1KΩ
Evaluation Board (PCB106_1)
32Khz Xtal
2.8V(AVDD)
1.8V(DVDD)
3.3V(DVDDIO)
R
3.3V
4.5V
IR
Gr
PPG Module
RT5707
RT5707
RT9703
RT3001
Accelerometer
I2C
Battery Charger
RT9527 +
LIR2430
RT48134.5V(Boost)
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 10 http://www.richtek.com
your power partner.
Schematic, Bill of Materials & Board Layout
EVB Schematic Diagram
Bill of Materials
Reference Qty Part number Description Package Manufacturer
BAT1 1 BT-BS-24-A1AJ001 SIP-2P CR2430 HUAI YANG
CON5 1 EJ-3699M-GP JACK_CON/5P/EJ-
3699M-GP
AUDIOJACK/5P/SMD/
EJ-3699M-GP Dian Jin
C3, C11, C12 3 C1005X7R1H104K050BB 100nF/50V/X7R C-0402 TDK
C5 1 C1005X5R1A475KT 4.7µF/6.3V/X7R C-0402 TDK
SWD_B
SIP-5P
11
22
33
44
55
PL1 0 ohm1 2
PL3 0 ohm1 2
VRLD_CON
PL2 0 ohm1 2FL
FR
ES
D1
ES
D /
AZ
53
25
-01
F
12
BGM11S22F256GA
RT1025
VCM
C107 10
uF
/ 04
02
/ 6.3
V / X
5R
21
ES
D2
ES
D /
AZ
53
25
-01
F
12
ES
D3
ES
D /
AZ
53
25
-01
F
12
R207
10
0K
/02
01
/1%
12
L1 2.2uH/1239AS-H-2R2M/25201 2
R7
88
06
K/0
40
2/1
%
12
AVDD28
PL4PL / MAKK2016H2R2M
1 2
U14
U / RT4813 / UQFN-9L
SW3
VIN8
SCL9
SDA5
VOUT2
FB7
EN1
GND6
PGND4
VIB
AFE_VBST_EN 3AFE_VBST_EN
AFE_VBST
DVDD_SYS DVDD_MCU
R209
10
0K
/02
01
/1%
12
R208
NC
/10
0K
/02
01
/1%
12
R210
NC
/10
0K
/02
01
/1%
12
NTC1NCP15X1-H103F03RC
12TS
PPG Power
FR 3FL 3
VRLD_CON 3
FLFRVRLD_CON
C8
1uF / 0402 / 6.3V / X7R21
VIN
EXT_Control 3
R84.7K/0402/1%
12
E_CLK
E_MISO
E_RSTB
E_MOSI
E_CSN
E_MOSI 3E_MISO 3
R94.7K/0402/1%
12
E_CLK 3E_CSN 3
R2010/0402/1%
1 2R2020/0402/1%
1 2
E_RSTB 3
R24 NC/0/0402/1%
1 2
DVDD18
C5
4.7uF / 0402 / 6.3V / X7R21
E_INT
BAT
E_INT 3
R4 1K/0402/1%
12
R211
10
0K
/02
01
/1%
12
R212
NC
/10
0K
/02
01
/1%
12
R213
10
0K
/02
01
/1%
12
BAT
E_PWDE_PWD 3
CHG_N
R190 NC/0/0402/1%
1 2
CH
G_
N
R1
12K/0402/1%
12
R5
68K/0402/1%
12
VIN
AFE_VPPG0_EN 3AFE_VPPG1_EN 3
TS
AFE_VPPG0_ENAFE_VPPG1_EN
R7 0/0402/1%
1 2
KA
D1
LED
AK
C98
22
uF
/06
03
/16
V/X
5R
21
VL
ED
AV
LE
DB
C101
22
uF
/06
03
/16
V/X
5R
21
EX
T_
Co
ntr
ol
AF
E_
VP
PG
1_
EN
AF
E_
VP
PG
0_
EN
AF
E_
VB
ST
_E
N
Z43 Hold1 1
Z44 Hold1 1
Z45 Hold1 1
AF
E_
VP
PG
0_
EN
1
Z46 Hold1 1
LDO_EN 3LDO_EN
AF
E_
VP
PG
1_
EN
1
Hold
EX
T_
Co
ntr
ol
1
EXT_Control
VL
ED
A
1
VL
ED
B
1
CHG_N 3CHG_N
E_INT
E_MISO
E_CLKE_CSN
E_MOSI
C261uF / 0402 / 6.3V / X7R
21
C99
22
uF
/06
03
/16
V/X
5R
21
C102
22
uF
/06
03
/16
V/X
5R
21
R22810K/0402/1%
12
KA
D3
LED
AK
LDO_EN
C108 10
uF
/ 04
02
/ 6.3
V / X
5R
21
R214
10
0K
/02
01
/1%
12
L2 2.2uH/1239AS-H-2R2M/25201 2
VDD18
C11 10
0n
F/5
0V
/X7
R/0
40
2
12
R215
10
0K
/02
01
/1%
12
R216
NC
/10
0K
/02
01
/1%
12
R217
10
0K
/02
01
/1%
12
R218
NC
/10
0K
/02
01
/1%
12
R219
NC
/10
0K
/02
01
/1%
12
R220
10
0K
/02
01
/1%
12
BAT
BAT
DVDD18
G_INT2 3
SW1SW KEY-YM061
132
4
G_SCL 3G_SDA 3
G_INT 3
SW1
G_INTG_INT2
BAT
G_SCLG_SDA
C12 10
0n
F/5
0V
/X7
R/0
40
2
12
M1P 1
M1N 1
M2P 1
VDD28 to RT1025
M2N 1
M2P
M3N 1
M3P 1 M3P
R235
10
0K
/02
01
/1%
12
M1P1
R203 0/0402/1%
1 2
TP1INT2
1G_INT2
R26100K/0201/1%
1 2
LDO
Charger
C16 2.2uF/6.3V/X5R/04021 2
Power Stage
HR_Sensor SFH7050G_Sensor
G_INT2
R193 NC/0/0402/1%
1 2 VLEDA
C18 2.2uF/6.3V/X5R/04021 2
VDD4.5 to PPG LED Green
AFE_VPPG0_EN
LEDB
INN_PPG
LEDA
INP_PPG
R15 1K/0402/1%1 2
RT1025_AVDD28
RT1025_DVDD18
For Testing
U7
RT1025/WLCSP
XTALOA7
XTALIB7
RSV4D7
VRLDE7
INN_ECGF7
INP_ECGG7
AVDD28H7
GNDA6
INTB1
RSV1C6
RSV5D6
GND_A0G3
INN_PPGH6
DVDD18A5
AFE_PWDB6
RSV0B5
INP_PPGG5
DVDDIOA4
RESETBA1 I2C_SELB4
GND_D1C5
GND_A1G6
VCMG4
VBGH4
SPI_CLK=SCLA3
SPI_MISOB3
GND_D0C3
GND_HV0G1
GND_HV1G2
GND_A2H3
SPI_CSN=SDAA2
SPI_MOSIE2
RSV2C2
TX1H2
RSV3B2
AVDD_HVC1
GND_HVD1
VLXE1
NCF1
TX2H1
GND_D2D2
XTALIXTALO
LHRHVRLD
E_RSTB
E_PWD
C21 2.2uF/6.3V/X5R/04021 2
X1
32.768KHz/TFX-02S-32
12
C1322/pF/0402/NPO2
1
C1522/pF/0402/NPO 2
1
C30
1u
F / 0
40
2 / 6
.3V
/ X7
R
21
DVDD18
XTALO
R12 100K/0201/1%
1 2
R13 100K/0201/1%
1 2
R14 100K/0201/1%
1 2FR
FL
C171uF / 0402 / 6.3V / X7R
21
R230 0/0402/1%
1 2
U6
BGM11S22F256GARESET_n
1
GND12
GND23
2G4RF_ANT_IN4
2G4RF_PORT5
GND36
PD97
PD108
PD119
PD
12
10
PD
13
11
PD
14
12
PD
15
13
PA
014
PA
115
PA
216
PA
317
PA
418
PA
519
PB
11
20
PB
12
21
PB
13
22
DNC123DNC224GND425V_BATT26GND527V_1V828GND629DNC330V_IOVDD31GND732PC633PC734PC835
PC
936
PC
10
37
PC
11
38
PF
039
PF
140
PF
241
PF
342
PF
443
PF
544
PF
645
PF
746
GN
D8
47
HF
XO
_IN
48
HF
XO
_O
UT
49
GN
D9
50
GND1051
GND1152
ANT_GND53
GND1254
GND1355
GND1456
E_
RS
TB
E_
CS
NE
_M
OS
I
SW
CL
KS
WD
IO
M2
N
M2
PE
_P
WD
R231 0/0402/1%
1 2
AFE_VBST
C23 2.2uF/6.3V/X5R/04021 2
RT1025_AVDD28
R233 0/0402/1%
1 2AVDD28RT1025_AVDD28
C3100nF/50V/X7R/0402
12
DVDD_MCU
R234 0/0402/1%
1 2DVDD18RT1025_DVDD18
DVDD_MCU
RESETn
DVDD_MCU
U2
NT1613A
B+1
B-2
VDD3
VM4
CO
UT
5
S26
S17
DO
UT
8
B-B-
XTALI
VDD 1
COUT 1
DOUT 1
BAT-
BAT+BAT
BAT1
11
22
Li-ion Protection
DVDD_SYS
BAT
DVDD_SYS
R204 10/0603/1%/0.25W1 2
G_SDAG_SCLG_INT
TP3 D6
1
DVDD_MCU
BV
R221 0/0402/1%
1 2
VIN
U16
RT5707WSC
SWA1
ENB1
VSEL1C1
VSEL2D1
VSEL3D2
VOUTC2
GNDB2
VINA2
R20150K/0402/1%
12
R1110K/0402/1%
12
U17
RT5707WSC
SWA1
ENB1
VSEL1C1
VSEL2D1
VSEL3D2
VOUTC2
GNDB2
VINA2
R191M/0402/1%
12
VIB
M3
P
M1
PM
3N
M1
N
SW
1L
DO
_E
N
C97
1u
F / 0
40
2 / 6
.3V
/ X7
R
21
C109 10
uF
/ 04
02
/ 6.3
V / X
5R
21
C110 10
uF
/ 04
02
/ 6.3
V / X
5R
21
C111 10
uF
/ 04
02
/ 6.3
V / X
5R
21
R7
91
00
K/0
20
1/1
%
12
DVDD_SYS DVDD_G_Sensor
R2230/0402/1%
12
VCM
R23 0/0402/1%
1 2
DVDD_G_Sensor
DVDD_G_Sensor
E_CLK
E_INTE_MISO
R8
01
00
K/0
20
1/1
%
12
R225 0/0402/1%
1 2
DVDD18
C112 10
uF
/ 04
02
/ 6.3
V / X
5R
21
C113 10
uF
/ 04
02
/ 6.3
V / X
5R
21
U15
RT9073A-33GQZ
VOUT1
GND2
EN3
VIN4
SG
ND
5
C105
1u
F / 0
40
2 / 6
.3V
/ X7
R
21
C106 1u
F / 0
40
2 / 6
.3V
/ X7
R
21
BAT
R206100K/0201/1%
12
U3
RT9527
VIN1
PGOOD_N2
CHG_N3
GND14
ISET5TIMER6TS7BAT8GND29
C24
1u
F / 0
40
2 / 6
.3V
/ X7
R
21
VDD33 to System
C22
1u
F / 0
40
2 / 6
.3V
/ X7
R
21
VL
ED
B
R226 NC/0/0402/1%
1 2
KA
D2
LED
AK
C114 10
uF
/ 04
02
/ 6.3
V / X
5R
21
R19810K/0402/1%
12
C20
33
0p
F /
04
02
/ 6
.3V
/
X7
R
21 C19
33pF / 0402 / 6.3V / X7R
21
C2533pF / 0402 / 6.3V / X7R
21
R17 62K/0402/1%
1 2
R18 62K/0402/1%
1 2
VIN 1VIN
AFE_VBST 1AFE_VBST
LH
RH
DVDD_SYS 1DVDD_SYS
AVDD28 1
U12
SFH7050
GC1
GA2
RA3
PA4
PC5 RC6
IA7
IC8
AVDD28
DVDD18 1
DVDD18
BLE STATUS
R227 0/0402/1%
1 2
VPPG 1
VPPG
VPPG
RESETn
DVDD_G_Sensor 1
SWDIOSWCLK
DVDD_G_Sensor
Z1
FK_1
1Z2
FK_1
1Z58
FK_1
1Z59
FK_1
1
U8
RT3001
SD
O1
SDA/SDI2
VDDIO3
NC
4
INT15
INT26
VDD7
GN
D8
GN
D9
CS
10
PS
11
SCL/SCK12
AFE_VPPG1_EN
G_INT
G_SCL
G_SDA
DVDD_MCU
DVDD_MCU 1
VPPG
RT1025_AVDD28 1
RT1025_AVDD28
RT1025_DVDD18 1
RT1025_DVDD18
M1N
M1P
LEDA
M2N
LEDA
M3N
LEDBINP_PPGINN_PPG
VBUS
BAT
TP17VIN_EKG_CON1
TP16VIP_EKG_CON1
TP18
VRLD_CON
1
R174 0/0402/1%
1 2
DVDD_SYS
FL
VRLD_CONFR
FL 2
VRLD_CON 2FR 2
FL
VRLD_CONFR
C104
1uF
/ 0402 / 6
.3V
/ X7R
21
E_CSNE_MISO
E_MISO 2E_MOSI 2
E_RSTB
E_MOSI
E_RSTB 2
E_CSN 2
E_PWD 2
E_INT 2
E_PWD
E_INTJP4
HEADER10X2
1 23 45 67 89 10
11 1213 1415 1617 1819 20
G_INT 2
G_INT2 2
G_SCL 2G_SDA 2
G_INT
G_INT2
G_SCLG_SDA
AFE_VPPG1_EN 2AFE_VPPG0_EN 2
AFE_VPPG0_ENAFE_VPPG1_EN
E_CLK 2E_CLK
DVDD_SYS
EXT_Control 3
AFE_VBST_EN 2AFE_VBST_EN
EXT_Control
E_CLK G_INTLDO_EN 2
E_MOSILDO_EN
E_CSN
E_MISO
G_INT2
G_SCL
CHG_NCHG_N 2
G_SDA
E_INT
AFE_VPPG1_ENAFE_VPPG0_EN
E_RSTBE_PWD
EXT_ControlAFE_VBST_EN
CHG_NLDO_EN
I/F
DVDD_SYS
ECG cable connector
USB3
USB
11
22
33
44
55
99
66
77 8
8
0.96" OLED
G_SDAG_SCL
DVDD_SYS
CON5JACK_CON/5P/EJ-3699M-GP
AUDIOJACK/5P/SMD/EJ-3699M-GP
1
2
3
5
4
JP2
NC/SIP-8P
11
22
33
44
55
66
77
88
D+D-
ID
D+1SIP-1P-SP1
ID2 SIP-1P-SP1
D-1 SIP-1P-SP1
VBUS
USB Micro-B
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 11 http://www.richtek.com
your power partner.
Reference Qty Part number Description Package Manufacturer
C8, C17, C22,
C24, C26, C30,
C97, C104,
C105, C106
10 C1005X5R0J105K050BB 1µF/6.3V/X5R C-0402 TDK
C13, C15 2 GRM1555C1H220FZ01D 22pF/NPO C-0402 Murata
C16, C18, C21,
C23 4 GRM155R61E225KE11D 2.2µF/6.3V/X5R C-0402 Murata
C19, C25 2 0402N330J500CT 33pF/6.3V/X7R C-0402 WALSIN
C20 1 0402B331K100 330pF/6.3V/X7R C-0402 WALSIN
C98, C99, C101,
C102 4 GRM188R60J226MEA0D 22µF/6.3V/X5R C-0603 Murata
C107, C108,
C109, C110,
C111, C112,
C113, C114
8 0402X106M100CT 10µF/6.3V/X5R C-0402 WALSIN
D1 1 LNL-191SUR Red LED LED_2P_RT1025 LIGH TOP
D2 1 LNL-190UB Blue LED LED_2P_RT1025 LIGH TOP
D3 1 LNL-190UW-4H White LED LED_2P_RT1025 LIGH TOP
ESD1, ESD2,
ESD3 3 ESD/D5V0L1B2S9-7 ESD R-0603 DIODES
L1, L2 2 DFE201610E-2R2M=P2 2.2µH/1239AS-H-
2R2M/2520 L-2-5X2-0 MuRata
NTC1 1 NCP15XH103F03RC NCP15X1-
H103F03RC R-0402 MuRata
PL1, PL2, PL3 3 WR06X000 PTL 0 L-0603 WALSIN
PL4 1 GBLM160808P-1R5M PL/GBLM160808P-
1R5M L-NR3015 GOTREND
R1 1 CR-02FL6---12K 12k/1% R-0402 Viking
R4, R15 2 WR04X1001FTL 1k/1% R-0402 WALSIN
R5 1 WR04X6802FTL 68k/1% R-0402 WALSIN
R7, R23, R174,
R201, R202,
R203, R221,
R223, R225,
R226, R227,
R230, R231,
R233, R234
15 WR04X000 PTL 0/1% R-0402 WALSIN
R8, R9 2 CR-02FL6---4K7 4.7k/1% R-0402 Viking
R11, R198, R228 3 WR04X1002FTL 10k/1% R-0402 WALSIN
R12, R13, R14,
R26, R79, R80,
R206, R207,
R209, R211,
R213, R214,
R215, R217,
R220, R235
16 WR02X1003FTL 100k/1% R-0201 WALSIN
R17, R18 2 WR04X6202FTL 62k/1% R-0402 WALSIN
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 12 http://www.richtek.com
your power partner.
Reference Qty Part number Description Package Manufacturer
R19 1 WR04X1004FTL 1M/1% R-0402 WALSIN
R20 1 WR04X1503FTL 150k/1% R-0402 WALSIN
R78 1 WR06X8063FTL 806k/1% R-0402 WALSIN
R204 1 WR06X000 PTL 0R R-0603 WALSIN
SW1 1 HTS 6601H TOUCH-BTN DIP-4P High-Tronics
USB3 1 UMMBF-051MGCB9-CF1066 USB Micro-B
Connector USB Micro-B Cherng Weei
U2 1 NT1613A-NQA-30-BJ Battery Protect IC QFN2X3_8L_0-5 Neotek
U3 1 RT9527GQW Charger IC WDFN-8L 2x2 Richtek
U6 1 BGM11S22F256GA BLE SiP BGM11S22F256GA SiLab
U7 1 RT1025WS ECG/PPG AFE IC WL-CSP-41B
3.10x3.48 (BS) Richtek
U8 1 RT3001GQL G-sensor LGA-12L 2x2 Richtek
U12 1 SFH7050 PPG LED & PD
Module SFH7050 OSRAM
U14 1 RT4813AGQUF 4.5V Boost IC UQFN-9L 2x2 (FC) Richtek
U15 1 RT9073A-33GQZ 3.3V LDO ZQFN-4L 1x1 Richtek
U16, U17 2 RT5707WSC 1.8V/2.8V Buck IC WL-CSP-8B 0.9x1.6
(BSC) Richtek
X1 1 DST-310S 32.768kHz/TFX-02S-
32 CRY-DST310S HARMONY
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 13 http://www.richtek.com
your power partner.
PCB Layout
Top View (1st layer)
PCB Layout—Inner Side (2nd Layer)
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 14 http://www.richtek.com
your power partner.
PCB Layout—Inner Side (3rd Layer)
Bottom View (4th Layer)
RT1025WS_P0 Evaluation Board
EVB_RT1025WS_P0-02 November 2018 15 http://www.richtek.com
your power partner.
More Information
For more information, please find the related datasheet or application notes from Richtek website
http://www.richtek.com.
Important Notice for Richtek Evaluation Board
THIS DOCUMENT IS FOR REFERENCE ONLY, NOTHING CONTAINED IN THIS DOCUMENT SHALL BE CONSTRUED AS RICHTEK’S WARRANTY, EXPRESS
OR IMPLIED, UNDER CONTRACT, TORT OR STATUTORY, WITH RESPECT TO THE PRESENTATION HEREIN. IN NO EVENT SHALL RICHTEK BE LIABLE TO
BUYER OR USER FOR ANY AND ALL DAMAGES INCLUDING WITHOUT LIMITATION TO DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL
DAMAGES.