remdial & stimulation

8/16/2019 Remdial & Stimulation

1/55


2/55


3/55

3

REMEDIAL & STIMULATION

Quick Reference Index

R&S Products Page

Alpha and Numeric Product Index ...................................... 4-5

Retrievable Service Packers and Accessories .................. 6-17

Retrievable Bridge Plugs and Accessories ..................... 18-25

Perforation Wash Tools and Accessories ........................ 26-29

Drillable Bridge Plugs ...................................................... 30-33

Drillable Cement Retainers ............................................. 33-35

Setting Tools and Accessories ........................................ 36-39

Casing Cleanup Equipment ............................................ 40-46

Rod Pumping Equipment and Accessories ..................... 47-53

Manifolds & Swivels ........................................................ 54-55


4/55

4


Product

Number Description PageProductNumber Description Page

Alphabetical Index

599-04 Back-Pressure Valve, Model “A” ............................................. 10

899-20 Bakerseal®

Thread Sealing Compound ..................................... 55806-88 Blanking Plug, Model “FWG”.................................................. 15

401-93 Bridge Plug, DELTA Wireline Set ........................................... 32

677-01 Bridge Plug, Model “C” Retrievable ................................... 18-19

677-34 Bridge Plug, Model “G” Lok-Set Retrievable ..................... 20-21

677-37 Bridge Plug, Model “GT” Lok-Set Retrievable................... 20-21

677-06 Bridge Plug, Model “H-1” Retrievable..................................... 18

401-03 Bridge Plug, Model “N & N2” Wireline (Tubing) ................... 33

401-22 Bridge Plug, Model “N-1” Mechanical Set ......................... 30-31

401-20 Bridge Plug, Model “N-1” Wireline Set .............................. 30-31

401-15 Bridge Plug, Model “N-3” Wireline Set (Tubing).................... 33

401-21 Bridge Plug, Model “NC-1” Wireline Set ........................... 30-31

401-23 Bridge Plug, Model “NC-1” Mechanical Set.......................30-31

401-19 Bridge Plug, Model “S” Wireline Set .................................. 30-31

677-39 Bridge Plug, Model “WG” Wireline Set Retrievable ............... 24

677-32 Bridge Plug, Wireline Set Retrievable .................................22-23

400-07 Cement Retainer, Model “B-1”, Mechanical Set (Tubing) ...... 33

400-11 Cement Retainer, Model “H-1”, Wireline Set (Tubing) ........... 33

400-21 Cement Retainer, Model “K-1”, Mechanical Set ................34-35

400-23 Cement Retainer, Model “K-1” Wireline Set ......................34-35

400-26 Cement Retainer, Model “N” Wireline Set (Tubing) ............... 33

400-22 Cement Retainer w/Flapper Valve, “K-1”, Mech. Set......... 34-35

400-24 Cement Retainer w/Flapper Valve, “K-1”, Wireline Set .....34-35

675-08 Circulating Sub, Model “F” ...................................................... 11

470-42 Circulating Washer, Model “C” Packing Element ................... 29

470-16 Circulating Washer, Model “E”................................................ 28

599-51 Collar Locator, Model “A-1”, Mechanical ............................... 27

430-61 Control Unit, Model “KL” ........................................................ 36

714-25 Control Valve, Injection ........................................................... 27

714-31 Control Valve, Model “C” Injection ......................................... 27

672-34 Control Valve, Model “E” Tubing ............................................ 10

598-10 Double Box Tubing Hanger Bushing ....................................... 49

437-24 Firing Head, Model “G” ........................................................... 39

410-01 Full-Bore Retrievable Cementer, Model “C-1” & “C-2” ....16-17

407-20 Hydro-Grip Cementer, Model “RC-2” .................................... 6-7

437-12 Hydrostatic High-Temp WL Pressure Setting Assy, “L” ......... 39

437-44 Ignitor, Model “BP-3S” ............................................................ 38

437-43 Ignitor, Secondary..................................................................... 38

439-44 Jar, Model “C” Wireline ........................................................... 39

428-02 Junk Basket, Model “B” ........................................................... 42

598-40 Manifold, Five-Valve Cementing ............................................. 54

598-24 Manifold, Four-Valve Cementing............................................. 54

598-33 Manifold, Model “B-1” Center Type Testing........................... 54

598-35 Manifold, Model “D” Testing ................................................... 54

598-41 Manifold, Model “E” Swivel Type Testing .............................. 54

598-13 Manifold, Six-Valve Cementing ............................................... 54

747-02 Milling Tool, Model “CB” Packer............................................ 44

747-03 Milling Tool, Model “CC”........................................................ 44

747-06 Milling Tool, Model “CJ” Packer........................................ 44-45

747-51 Milling Tool, Model “CJ-1” Packer ......................................... 44

747-08 Milling Tool, Model “CK” ....................................................... 44665-11 Packer Plugs, Model “D-1 & D-2” Latching Type ................... 25

665-12 Packer Plug, Model “F” Latching Type.................................... 25

665-18 Packer Plug, Model “FT” Latching Type ................................. 25

747-12 Plug Plucker, Model “CP-1”..................................................... 46

717-90 Pressure Relief Sub ................................................................... 49

714-10 Pressure-Actuated Stimulation Valve ....................................... 10

— Prestrain Tables/Information ............................................... 50-53

407-15 Retrievamatic II, Rocker Slips .................................................8-9

407-19 Retrievamatic II, Dovertail Slips .............................................8-9

407-05 Retrievamatic Cementer, Model “EA” .................................... 6-7

407-09 Retrievamatic/Hurricane Plug, Model “B” ...................... 12 & 14

407-18 Retrievamatic/Hurricane Plug, Model “L” .......................... 13-14

407-14 Retrievamatic/Hurricane Plug, Model “J” ........................... 13-14

677-71 Retrieving Head, Model “H” Washover Type .......................... 19

677-75 Retrieving Head, Model “L” Lok-Set ....................................... 20

677-78 Retrieving Head, Model “LT-CT” & “LTC” Lok-Set® ............ 20

677-76 Retrieving Head, Model "M” Washover Type ......................... 22

407-90 Rotational Equalizing Sub ........................................................ 15

441-90 Safety Joint Overshot................................................................ 15

441-35 Safety Joint, Twin-Thread ........................................................ 15

747-41 Sand-Line Drill, Model “A-2” .................................................. 43

620-03 Scraper, Model “C-3” Roto-Vert™ Casing ......................... 40-41

620-61 Scraper, Model “D” Roto-Vert™ Tubing................................. 41

677-94 Sealer Ball Catcher for Model “C” & “H-1” Bridge Plug ........ 19

677-95 Sealer Ball Catcher for Model “G” Lok-Set Bridge Plug......... 21

470-43 Service Adaptable Packer-SAP™ Tool .................................... 26

400-62 Setting Tool, Model “CT”, Hydraulic ...................................... 37

400-69 Setting Tool, Model “K-1” Snap Latch .................................... 36

400-66 Setting Tool, Model “NC-1” Mechanical ................................. 37

437-66 Slow Set Power Charge ............................................................ 38

400-92 Snap Latch Stinger Sub, Model “B” ......................................... 36

437-64 Standard Power Charge ............................................................ 38

714-19 Surge Valve, Model “A” Upper ................................................ 11

714-09 Surge Valve System, Model “A” Dual ..................................... 11

714-03/4 Surge Valve System, Model “D” .............................................. 11

714-02 Test & Stimulation Valve, Model “F” ...................................... 10

698-31 Tubing Anchor Catcher, Hydraulic Set .................................... 49

698-03 Tubing Anchor Catcher, Model “B-2” ................................ 47-48


698-05 Tubing Anchor Catcher, Model “DB” ...................................... 49

747-50 Tubing Bailer, Pump Type........................................................ 43

598-01 Tubing Swivel, Model “D” ....................................................... 54

672-01 Tubing Tester, Model “N” Full-Bore ....................................... 16

672-05 Tubing Tester, Model “S” Full-Bore .......................................... 6

671-03 Unloading Sub, Model “P-2” Set-Down................................... 15

675-05 Unloading Sub, Model “R” Upstrain ........................................ 16

439-01 Wireline Feeler & Junk Catcher, Model “H” ........................... 39

439-07 Wireline Feeler & Junk Catcher, Model “R”............................ 39

437-02 Wireline Pressure Setting Assembly, Model “E-4” .................. 38


5/55

5


Product Number IndexProductNumber Description Page

ProductNumber Description Page

— Prestrain Tables/lnformation................................................ 50-53

400-07 Cement Retainer, Model “B-1”, Mechanical Set (Tubing) ...... 33400-11 Cement Retainer, Model “H-1”, Wireline Set (Tubing) ........... 33

400-21 Cement Retainer, Model “K-1”, Mechanical Set ................34-35

400-22 Cement Retainer w/Flapper Valve, “K- 1”, Mech. Set ........ 34-35

400-23 Cement Retainer, Model “K-1” Wireline Set ......................34-35

400-24 Cement Retainer w/Flapper Valve, “K-1”, Wireline Set .....34-35

400-26 Cement Retainer, Model “N”, Wireline Set (Tubing) .............. 33

400-62 Setting Tool, Model “CT”, Hydraulic ...................................... 37

400-66 Setting Tool, Model “NC-1” Mechanical ..................................37

400-69 Setting Tool, Model “K-1” Snap Latch .................................... 36

400-92 Snap Latch Stinger Sub, Model “B” ......................................... 36

401-03 Bridge Plug, Model “N & N2” Wireline (Tubing) ................... 33

401-15 Bridge Plug, Model “N-3” Wireline Set (Tubing).................... 33

401-19 Bridge Plug, Model “S” Wireline Set ..................................30-31

401-20 Bridge Plug, Model “N-1” Wireline Set .............................. 30-31

401-21 Bridge Plug, Model “NC-1” Wireline Set ...........................30-31

401-22 Bridge Plug, Model “N-1” Mechanical Set ......................... 30-31

401-23 Bridge Plug, Model “NC-1” Wireline Set ...........................30-31

401-93 Bridge Plug, DELTA Wireline Set ........................................... 32

407-05 Retrievamatic Cementer, Model “EA” .................................... 6-7

407-09 Retrievamatic/Hurricane Plug, Model “B” ...................... 12 & 14

407-14 Retrievamatic/Hurricane Plug, Model “J” ........................... 13-14

407-15 Retrievamatic II, Rocker Slips ................................................. 8-9

407-18 Retrievamatic/Hurricane Plug, Model “L” .......................... 13-14

407-19 Retrievamatic II, Dovetail Slips ............................................... 8-9

407-20 Hydro-Grip Cementer, Model “RC-2” .................................... 6-7

407-90 Rotational Equalizing Sub ........................................................ 15

410-01 Full-Bore Retrievable Cementer, Model “C-1” & “C-2” ....16-17

428-02 Junk Basket, Model “B” ........................................................... 42

430-61 Control Unit, Model “KL” ........................................................ 36

437-02 Wireline Pressure Setting Assembly, Model “E-4” .................. 38

437-12 Hydrostatic High-Temp WL Pressure Setting Assy, “L” ......... 39

437-24 Firing Head, Model “G” ........................................................... 39

437-43 Ignitor, Secondary..................................................................... 38

437-44 Ignitor, Model “BP-3S” ............................................................ 38

437-64 Standard Power Charge ............................................................ 38

437-66 Slow Set Power Charge ............................................................ 38

439-01 Wireline Feeler & Junk Catcher, Model “H” ........................... 39

439-07 Wireline Feeler & Junk Catcher, Model “R” ............................ 39

439-44 Jar, Model “C” Wireline ........................................................... 39

441-35 Safety Joint, Twin-Thread ........................................................ 15

441-90 Safety Joint Overshot ................................................................ 15

470-16 Circulating Washer, Model “E” ................................................ 28

470-42 Circulating Washer, Model “C” Packing Element ................... 29

470-43 Service Adaptable Packer-SAP™ Tool ..................................... 26

598-01 Tubing Swivel, Model “D” ....................................................... 54

598-10 Double Box Tubing Hanger Bushing ....................................... 49

598-13 Manifold, Six-Valve Cementing ............................................... 54

598-24 Manifold, Four-Valve Cementing............................................. 54

598-33 Manifold, Model “B-1” Center Type Testing........................... 54

598-35 Manifold, Model “D” Testing ................................................... 54

598-40 Manifold, Five-Valve Cementing ............................................. 54598-41 Manifold, Model “E” Swivel Type Testing .............................. 54

599-04 Back-Pressure Valve, Model “A” ............................................. 10

599-51 Collar Locator, Model “A-1”, Mechanical ............................... 27

620-03 Scraper, Model”C-3" Roto-Vert™ Casing ............................ 40-41

620-61 Scraper, Model “D” Roto-Vert™ Tubing .................................. 41

665-11 Packer Plugs, Model “D-1 & D-2” Latching Type ................... 25

665-12 Packer Plug, Model “F” Latching Type .................................... 25

665-18 Packer Plug, Model “FT” Latching Type ................................. 25

671-03 Unloading Sub, Model “P-2” Set-Down................................... 15

672-01 Tubing Tester, Model “N” Full-Bore ....................................... 16

672-05 Tubing Tester, Model “S” Full-Bore .......................................... 6

672-34 Control Valve, Model “E” Tubing............................................ 10

675-05 Unloading Sub, Model “R” Upstrain ........................................ 16

675-08 Circulating Sub, Model “F” ...................................................... 11

677-01 Bridge Plug, Model “C” Retrievable ................................... 18-19

677-06 Bridge Plug, Model “H-1” Retrievable..................................... 18

677-32 Bridge Plug, Wireline Set Retrievable .................................22-23

677-34 Bridge Plug, Model “G” Lok-Set Retrievable .....................20-21

677-37 Bridge Plug, Model “GT” Lok-Set Retrievable ................... 20-21

677-39 Bridge Plug, Model “WG” Wireline Set Retrievable ............... 24

677-71 Retrieving Head, Model “H” Washover Type .......................... 19

677-75 Retrieving Head, Model “L” Lok-Set ....................................... 20

677-76 Retrieving Head, Model “M” Washover Type ......................... 22

677-78 Retrieving Head, Model “LT-CT” & “LTC” Lok-Set® ..................... 20

677-94 Sealer Ball Catcher for Model “C” & “H-1” Bridge Plugs ...... 19

677-95 Sealer Ball Catcher for Model “G” Lok-Set Bridge Plug......... 21



698-05 Tubing Anchor Catcher, Model “DB” ...................................... 49

698-31 Tubing Anchor Catcher, Hydraulic Set .................................... 49

714-02 Test & Stimulation Valve, Model “F” ...................................... 10

714-03/4 Surge Valve System, Model “D” .............................................. 11

714-09 Surge Valve System, Model “A” Dual ..................................... 11

714-10 Pressure-Actuated Stimulation Valve ....................................... 10

714-19 Surge Valve, Model “A” Upper ................................................ 11

714-25 Control Valve, Injection ........................................................... 27

714-31 Control Valve, Model “C” Injection ......................................... 27

717-90 Pressure Relief Sub ................................................................... 49

747-02 Milling Tool, Model “CB” Packer ............................................ 44

747-03 Milling Tool, Model “CC”........................................................ 44

747-06 Milling Tool, Model “CJ” Packer ........................................44-45

747-08 Milling Tool, Model “CK” ....................................................... 44

747-12 Plug Plucker, Model “CP-1” ..................................................... 46

747-41 Sand-Line Drill, Model “A-2” .................................................. 43

747-50 Tubing Bailer, Pump Type........................................................ 43

747-51 Milling Tool, Model “CJ-1” Packer ......................................... 44

806-88 Blanking Plug, Model “FWG”.................................................. 15

899-20 Bakerseal® Thread Sealing Compound ..................................... 55


6/55

6


Model “EA”Retrievamatic Cementer

Product No. 407-05

MODEL “EA”™

RETRIEVAMATIC CEMENTERProduct No. 407-05

The industry’s most popular and provenretrievable stimulation and workoverpacker, the Retrievamatic is used in all

types of squeeze cementing, casing test-ing, formation fracturing, and high-pres-

sure acidizing with subsequent testing. Itis a full-opening, set-down packer withpiston-type hold-down buttons, actuated

by pressure from below, and a three-section packing element system. Test-

ing of the run-in string is possible with aModel “S” ™ Full-Bore Tubing Tester

(Product No. 672-05).

FEATURES/BENEFITS• Large bypass area permits circulation

around and through the tool while run-

ning in; straight pick-up equalizes pres-sure across hold-down buttons in-

stantly• Proven face-seal unloader controls the

bypass, eliminating the need for me-

chanical locks and rotation• Bypass running completely through

the packer isolates buttons from tub-ing pressure surges, reducing chance

of dulling• Hold-down buttons maintain packoff

during high-pressure operations from

below• Proven packing element system

• Rocker slips set with only 3/4 turn,straight pick-up to retrieve

MODEL “S” FULL-BORETUBING TESTERProduct No. 672-05

Designed for use with the RetrievamaticCementer, the Model “S” ™ Tubing Tester

is used to pressure test the tubing stringfor leaks.

Model “S” Tubing TesterProduct No. 672-05

MODEL “RC-2”™

HYDRO-GRIP CEMENTERProduct No. 407-20

The Model “RC-2” Hydro-Grip Cementeris a tubing size set-down packer withhydraulic hold-down pistons. The packer

has moderate pressure capabilities suit-able for most acidizing, fracturing, and

squeeze operations. The packer setswith right-hand rotation. (Tool is notshown).


both through and around the tool dur-

ing run-in

• Hydraulic hold-down buttons help tohold packer when pressuring from

below


7/55

7


4-1/2 114,3 9.5-13.5 14,1-20,1 43A 3.771 95,78 3.625 92,08 3.734 94,84 3.910 99,31 4.090 103,89 3.820 97,03 4.090 103,89 5 127 15-18 22,3-26,8 43B 4.125 104,78 3.937 100,00 3.937 100,00 4.250 107,95 4.408 111,96 4.126 104,80 4.409 111,99

11.5-15* 17,1-22,4 43C 4.250 107,95 4.156 105,56 4.125 104,78 4.408 111,96 4.560 115,82 4.274 108,56 4.561 115,85

26 38,7

20-23 29,8-34,2 44 4.406 111,91 4.312 109,52 4.375 111,13 4.625 117,48 4.778 121,36 113,89 4.778 121,36

5-1/2 139,7 45A2 4.500 114,3 4.375 111,13 4.500 114,3 4.600 116,86 4.950 125,73

15.5-20* 23,1-29,8 4 5A4 4.641 117,88 4.778 121,36 4.950 125,73

13-15.5 19,3-23,1

5-3/4 146,05 22.5 33,5 45B 4.781 121,44 4.687 119,05 4.781 121,44 4.950 125,83 5.190 131,83 4.764 121,01 5.190 131,83

26 38,7

6 152,4 20-23 29,8-34,2 45C 5.062 128,57 4.937 125,40 5.062 128,57 5.191 131,85 5.390 136,91 5.000 127,0 5.390 136,91

15-18 22,3-26,8 45D 5.156 130,96 5.391 136,93 5.560 141,22 5.136 130,45 5.560 141,22

34 50,6 45E2 5.406 137,31 5.250 133,35 5.406 137,31 5.561 141,25 5.609 142,47 5.386 136,80 5.791 147,09

6-5/8 168,28 28-32 41,7-47,6 4 5E4 5.484 139,28 5.610 142,49 5.791 147,09

24-29 35,7-43,2 45F 5.625 142,88 5.500 139,7 5.609 142,49 5.761 146,33 5.921 150,39 5.632 143,05 5.941 151,16 24 35,7 47A2 5.656 143,66 5.830 148,08 5.937 150,80

7 177,8 38 56,5 5.500 139,7 5.656 143,66 5.597 142,16 6.135 155,83

6-5/8 168,28 17-20 25,3-29,8 4 7A4 5.812 147,62 5.938 150,83 6.135 155,83

32-35 47,6-52,1

7 177,8 26-29 38,7-43,2 4 7B2 5.968 151,59 5.750 146,05 5.968 151,59 6.136 155,85 6.276 159,41 5.861 148,87 6.538 166,07

*20-26 29,8-38,7 4 7B4 6.078 154,38 6.276 159,41 6.456 163,98

17-20 25,3-29,8 47C2 6.266 159,16 6.125 155,58 6.250 158,75 6.456 163,98 6.578 167,08 6.297 159,94 6.884 174,85

33.7-39 50,1-58,0 47C4 6.453 163,91 6.579 167,11 6.797 172,64

7-5/8 193,68 24-29.7 35,7-44,2 47D2 6.672 169,47 6.500 165,1 6.671 169,44 6.798 172,67 7.025 178,44 6.545 166,24 7.132 181,15

20-24 29,8-35,7 47D4 6.812 173,02 7.025 178,44 7.125 180,98

44-49 65,5-72,9 4 9A2 7.312 185,72 7.000 177,8 7.312 185,72 7.511 190,78 7.687 195,25 7.423 188,54 8.060 204,72

8-5/8 219,08 32-40 47,6-57,9 4 9A4 7.531 191,29 7.688 195,28 7.921 201,19

20-28 29,8-40,5 49B 7.781 197,64 7.500 190,5 7.781 197,64 7.922 201,22 8.191 208,05 7.919 201,14 8.255 209,68

47-53.5 69,9-79,6 5 1A2 8.218 208,74 7.937 201,60 8.218 208,74 8.343 211,91 8.681 220,50 8.117 206,17 8.934 226,92 9-5/8 244,48 40-47 57,9-69,9 5 1A4 8.437 214,30 8.681 220,50 8.835 224,40

29.3-36 43,6-53,6 51B 8.593 218,26 8.375 212,73 8.593 218,27 8.836 224,43 9.063 230,20 8.539 216,89 9.063 230,20

65.7-81 97,8-120,5 53A2 9.000 228,6 8.875 225,43 9.000 228,6 9.094 230,99 9.560 242,82 9.000 228,6 9.903 251,54

10-3/4 273,05 55.5-60.7 82,6-90,3 5 3A4 9.375 238,13 9.504 241,40 9.760 247,90 9.392 238,56 10.020 254,51

45.5-51 67,7-75,9 5 3A6 9.625 244,48 9.250 234,95 9.375 238,13 9.850 250,19 9.950 252,73

32.75-40.5 48,7-60,3 53B 10.050 255,27 10.192 258,88 9.642 244,91 10.270 260,86

11-3/4 298,45 65-80.5 96,7-119,8 54A 10.125 257,18 10.000 254 10.125 257,18 10.406 264,31 10.682 271,32 10.250 260,35 10.711 272,06

38-60 56,5-89,3 5 4B 10.250 260,35 10.187 258,75 10.772 273,61 11.150 283,21 10.612 269,54 11.313 287,35

13-3/8 339,73 77-102 114,6-151,8 55A 11.625 295,28 11.625 295,28 11.625 295,28 11.733 298,02 12.275 311,79 11.633 295,48 12.464 316,59

48-72 71,4-107,1 55B 12.125 307,98 11.812 300,02 12.191 309,65 12.715 322,96 12.133 308,18 12.800 325,12

* This size may be set in this weight casing in certain circumstances such as mixed strings or unusual hole conditions; however, the other size listed for this weight is recommended andshould be run where possible.

‡ lt may be necessary to turn OD of gauge ring, guide ring, and packing element spacers when running in minimum ID casing.• This dimension is only for guidance in situations where there may be restricted diameters the tool has to pass. In some sizes the slips are bottomed out and will not set without

being damaged.

MODEL “RC-2” HYDROGRIP, PRODUCT NO. 407-20 &MODEL “EA” RETRIEVAMATIC CEMENTER, PRODUCT NO. 407-05

SPECIFICATION GUIDE

Casing Packing Packing Slips & Buttons Range

Weight Tool Gauge, Guide Element Element Preferred AbsoluteOD T&C Size Ring OD ‡ OD Spacer OD ‡ Min Max Min• Max

In. mm lb/ft kg/m In. mm In. mm In. mm In. mm In. mm In. mm In. mm

28A 2.234 56,74 2.125 53,98 — —

6.4-6.5 9,5-9,7 2 8A 2.330 59,18 — — 2.347 59,61 2.441 62,00 2.223 56,46 2.445 62,10

2-7/8 73,03 (Hi-Temp) 2.312 58,72

4.7-5.6 7,0-8,3 2 8B 2.357 59,87 — — 2.442 62,03 2.563 65,10 2.356 59,84 2.570 65,28

4.36 6,5 28C 2.436 61,87 — — 2.485 63,12 2.579 65,51 2.436 61,87 2.579 65,51

10.2 15,2 35A 2.782 70,66 2.750 69,85 2.782 70,66 2.834 71,98 2.922 74,22 2.767 70,28 2.956 75,08

3-1/2 88,9 7.7-9.2 11,5-13,7 35B 2.844 72,24 2.923 74,24 3.068 77,93 2.815 71,50 3.068 77,93

5.75 8,6 35C 3.038 77,17 3.000 76,2 3.038 77,17 3.069 77,95 3.188 80,98 3.033 77,04 3.222 81,84

4 101,6 9.5-11.6 14,1-17,3 41A 3.303 83,90 3.281 83,34 3.303 83,90 3.428 87,07 3.548 90,12 3.304 83,92 3.551 90,20

4-1/2 114,3 15.1 22,5 41B 3.620 91,95 3.594 91,29 3.620 91,95 3.754 95,35 3.826 97,18 3.620 91,95 3.871 98,32


8/55

8


New!

RETRIEVAMATIC II™

Product No. 407-15(Rocker Slips)Product No. 407-19(Dovetail Slips)

The Retrievamatic II is a compression

set, retrievable service packer used forremedial applications where the Model“EA” ™ Retrievamatic Cementer is often

used. These applications may includesqueeze cementing, casing testing, for-

mation fracturing and high pressureacidizing. The Retrievamatic II retains

the industry proven features and advan-tages of the Model “EA” Retrievamaticwhile incorporating design improvements

which will enhance the performance ofthe packer while lowering the mainte-

nance costs of the tool. It, like the Model“EA” Retrievamatic, is a full-opening

packer with piston-type hold-down but-tons actuated by pressure from below,and a three-section packing element

system. Companion tools such as theModel “S”™ Tubing Tester (Product No.

672-05) will be the same as those usedwith the Model “EA” Retrievamatic

Cementer.

FEATURES/BENEFITS• Retains the same features/benefits as

the Model “EA” Retrievamatic includ-ing a concentric internal bypass, face-

seal unloader, hydraulic hold-downbuttons and three-section packing el-

ement system• Dovetail or Rocker Type Slip designs

available according to job requirements

• Interchangeable parts with the “SAP”™

Tool minimizing spare parts inventory

• Square shaped key/keyway replacesthe dovetail key design increasing life

of the mandrel and reduces jammingand breaking of keys

• Buttress profile grooves on the Con-

trol Segment and Body increase thelife of the Body and Control Segment

• Conversion to right-hand or left-handset possible without additional parts or

disassembly of the tool• Heavy duty unloader and body for use

as a Hurricane Plug

Retrievamatic IIw/Dovetail Slips

Product No. 407-19

Retrievamatic IIw/Rocker Slips

Product No. 407-15


9/55

9


Casing Gauge & Packing Packing Rocker Slips and Button Range Dovetail Slips and Button RangeWeight Packer Guide Element Element Preferred Absolute Preferred Absolute

OD T&C Size Ring ODB OD Spacer ODB Min Max Min C Max Min Max Min C Max

In. lb/ft In. In. In. In. In. In. In. In. In. In. In.mm kg/m mm mm mm mm mm mm mm mm mm mm mm

9.5 A - 13.5 43A2 3.771 3.625 3.7344-1/2 14,1 - 20,1 95,78 92,08 97,84 3.910 4.090 3.820 4.090 3.910 4.090 3.771 4.186

114,3 9.5 - 10.5 43A4 4.000 99,31 103,31 97,03 103,89 99,31 103,89 95,78 106,32 14,1 - 15,6 101,6 3.937 3.937

15 - 18 4.125 99,96 99,98 4.250 4.408 4.126 4.409 4.250 4.408 4.125 4.5765 22,3 - 26,8 43B 104,78 107,95 111,96 104,80 103,89 107,95 111,96 104,78 116.23

127,0 11.5 - 15 A

17,1 - 22,4 43C 4,250 4.156 4.125 4.560 4.561 4.408 4.560

26 107,95 105,56 104,78 115,82 115,85 111,96 115,82 38,7

14 - 28.4D 44A 4.25020,8 - 42,3 107,95 4.125 4.250

14 - 26D 44B 4.360 104,78 107,95 20,8 - 38,7 110,74 4.408 4.950 4.274 5.000 4.250 5.060 4.250 5.060

14 - 23D 44C 4.485 111,96 125,73 108,56 127,0 107,95 128,52 107,95 128,52 5-1/2 20,8- 34,2 113,92 4.382 4.360

139,7 14 - 17D 44D 4.700 111,30 110,74 20,8 - 25,3 119,38

20 - 23 45A2 4.50029,8 - 34,2 114,3 4,375 4.500 4.625 4.950 4.600 4.950 4.625 4.950 4.484 5.161

15.5 - 20 A 4.641 1 11,13 114,3 117,48 125,73 116,84 125,73 117,48 125,73 113,89 131,09 23,1 - 29,8 45A4 117,88

13 - 15.519,3 - 23,1

5-3/4 22.5 45B 4.781 4.687 4.781 4.950 5.190 4.764 5.190 4.950 5.190 4.764 5.264146,1 33,5 121,44 119,05 121,44 125,73 131,83 121,01 131,83 125,73 131,83 121,01 113,71

2638,7

6 20 - 23 45C 5.062 5.191 5.390 5.000 5.390 5.191 5.390 5.000 5.590152,4 29,8 - 34,2 128,57 4.937 5.062 1 31,85 136,91 127,0 136,91 131,85 136,91 127,0 141,99

15 - 18 45D 5.156 125,40 128,57 5.391 5.560 5.136 5.560 5.691 5.560 5.136 5.74422,3 - 26,8 130,96 136,93 141,22 130,45 141,22 144,55 141,22 130,45 145,87

34 45E2 5.40650,6 137,31 5.250 5.406 5.561 5.791 5.386 5.791 5.561 5.791 5.386

28 - 32 45E4 5.484 133,35 137,31 141,25 147,09 136,80 147,09 141,25 147,09 136,80 5.8446-5/8 41,7 - 47,6 139,29 148,44

168,3 24 - 29A 45F 5.625 5.609 5.761 5.921 5.632 5.941 5.761 5.921 5.63235,7 - 43,2 142,88 142,47 146,33 150,39 143,05 150,91 146,33 150,39 143,05

2435,7 47A2 5.656

7 38 143,66 5.500177,8 56,5 139,7 5.656 5.830 6.135 5.597 6.135 5.830 6.135 5.597 6.112

6-5/8 17 - 20 143,66 148,08 155,83 142,16 155,83 148,08 155,83 142,16 155.24 168,3 35,3 - 29,8 47A4 5.812

32 - 35 147,62 47,6 - 52,1

26 - 29 47B2 5.9687 38,7 - 43,2 151,59 5.750 5.968 6.136 6.456 5.861 6.538 6.136 6.456 5.861 6.421

177,8 20 - 26A 47B4 6.078 146,05 151,59 155,85 163,99 148,87 166,07 155,85 163,98 148,87 163,09 29,8 - 38,7 154,38

17 - 20 47C2 6.26625,3 - 29,8 159,16 6.125 6.250 6.456 6.797 6.297 6.884 6.276 6.797 6.297 6.855

33.7 - 39 47C4 6.453 155,58 158,75 163,98 172,64 159,94 174,85 159,41 172,64 159,94 174,12 50,1 - 58,0 163,91

7-5/8 24 - 29.7 47D2 6.672193,7 35,7 - 44,2 169,47 6.500 6.671 6.798 7.125 6.545 7.132 6.798 7.125 6.545 7.083

20 - 24 47D4 6.812 165,10 169,44 172,67 180,98 166,24 181,15 172,67 180,98 166,24 179,9129,8 - 35,7 173,02

44 - 49 49A2 7.31265,5 - 72,9 185,72 7.000 7.312 7.511 7.921 7.423 8.060

8-5/8 32 - 40 49A4 7.531 177,80 185,72 190,78 201,19 188,54 204,72 7.500 8.500 7.312 8.568219,1 47,6 - 57,9 191,29 190,50 215,90 185,72 217,63

20 - 28 49B 7.781 7.500 7.781 7.922 8.191 7.919 8.25529,8 - 40,5 197,64 190,50 197,64 201,22 208,05 201,14 209,68

A This size may be set in this weight casing in certain circumstances such as mixed strings or unusual hole conditions; however, the other size listed for this weight is recommended and shouldbe run where possible.

B lt may be necessary to turn OD of gauge ring, guide ring, and packing element spacers when running in minimum ID casing.C This dimension is only for guidance in situations where there may be restricted diameters the tool has to pass. In some sizes the slips are bottomed out and will not set without being damaged.D The size 44 Retrievamatic II is intended for use where increased running clearance is necessary. Use size 45 tools whenever possible.

“The size 44 Retrievamatic II with rocker slips will not set in 5-1/2” 14 lb (139.7 mm 6.35 kg) casing, therefore dovetail slips must be used.”

Pressure ratings will vary according to casing size and gauge ring used. Consult Engineering for appropriate ratings.

RETRIEVAMATIC II™

PRODUCT NOS. 407-15 & 407-19SPECIFICATION GUIDE


10/55

10


Pressure-ActuatedStimulation Valve

Product No. 714-10

Model “F” Test andStimulation Valve

Product No. 714-02

MODEL “A”™ BACK-PRESSURE VALVEProduct No. 599-04

The Model “A” Back-Pressure Valve pro-vides a means of controlling back-flowwhen either running or pulling a run-in

string. Depending on the fluid in thewellbore, a fire and safety hazard is

eliminated.Its primary application is in conjunc-

tion with a full-bore retrievable cementer

and a Model “C” ™ or “H-1” ™ RetrievableBridge Plug or a Model “EA” ™

Retrievamatic Cementer and a Model“G” ™ Retrievable Bridge Plug, to control

backflow when moving from a treated

zone to straddle a new zone.The flapper valve can be locked in the

open position for swab or flow testing.

FEATURES/BENEFITS• Valve controls backflow when moving

from a treated zone to straddle a newzone

MODEL “E”™ TUBINGCONTROL VALVEProduct No. 672-34

The Model “E” Tubing Control Valve is afull-opening valve that can be used abovea Retrievamatic cementer to isolate a

zone from the tubing hydrostatic aftersqueeze cementing in a low-fluid-level

well. Valve opening is accomplishedwith right-hand rotation, with six andone-half turns at the tool, moving the

valve from fully closed to fully open posi-tion. Opening or closing can be repeated

as often as desired.The valve can also be used as a

control valve to prevent flowback while

running, moving or retrieving downholetools.

FEATURES/BENEFITS• Full-opening valve can be used to

isolate a zone from tubing hydrostatic

after squeeze cementing in a low-fluid-level well

MODEL “F”™ TEST ANDSTIMULATION VALVEProduct No. 714-02The Model “F” Test and Stimulation Valveis a rotationally actuated, quick-opening,

full-bore valve. It is used in conjunctionwith a Retrievamatic cementer, for the

purpose of creating sudden, high-veloc-ity flow from the formation through the

perforations into the tubing. Pluggedperforations are cleared, and blockingagents in the vicinity of the wellbore are

removed.

Also applicable in:

(1) dry testing of perforated intervals that

have been cemented off.(2) lowering injection pressures in water

injection wells by clearing blockedflow passages and perforations.

(3) removal of mud filtrate prior to an

acidizing job.(4) testing of a zone without swabbing

operations.

PRESSURE-ACTUATEDSTIMULATION VALVEProduct No. 714-10The Pressure-Actuated StimulationValve is a test and stimulation valve that

is actuated by pressure applied to theannulus. This feature makes it espe-

cially applicable to operations involvingdeep or deviated holes where rotation of

the tubing or drillpipe proves difficult. Itcan be used for any operation in whichthe Model “F” Test and Stimulation Valve

is used, provided it is possible to pres-sure the annulus. Tool actuation is ef-

fected by pressuring the annulus to 1000psi (70,31 kg/cm 2 ). It is the lower valve

in the Model “A” Dual Surge System(Product No. 714-09).

Model “A” Back-Pressure Valve

Product No. 599-04

Model “E” TubingControl Valve

Product No. 672-34


11/55

11


MODEL “A”™ UPPERSURGE VALVEProduct No. 714-19

The Model “A” Upper Surge Valve isdesigned to contain surges from below.It is run in with the valve in the closedposition. The valve can be opened bypressuring the tubing from above whichwill lock the valve in the open position. Itis the top valve in the Model “A” DualSurge Valve System (Product No. 714-09).

MODEL “A”™ DUALSURGE SYSTEMProduct No. 714-09

The Model “A” Dual Surge System con-sists of the Model “A” Upper Surge Valve(Product No. 714-19) spaced above thePressure-Activated Stimulation Valve(Product No. 714-10). Both of the valvesare run in the closed position, creating anatmospheric chamber between them.This setup is run on top of an “EA” ™

Retrievamatic Cementer that is set aboveperforations. The Pressure ActivatedStimulation Valve is opened by pressur-ing the annulus. The pressure at theperforations is dropped to zero and thesurge from the formation cleans out the

debris. The upper surge valve safelycontains the surge and allows circula-tion. It can be opened by pressuringdown the tubing.

FEATURES/BENEFITS• Surge safely contained in tubing• No rotation required• Valves opened by annulus and tubing

pressure

MODEL “D”™ SURGEVALVE SYSTEMProduct Nos. 714-04 & 714-03

The Model “D” Surge Valve System con-sists of the Model “D” Annulus ActivatedSurge Valve (Product No. 714-04) run asthe lower valve and the Model “D” Tub-ing Activated Surge Valve (Product No.714-03) run as the upper valve. Thevalves are run in the closed position withan atmospheric chamber between them.This arrangement is run on top of an “EA”Retrievamatic which is set above an in-terval of perforations. When the annulusis pressured, it actuates a cutter in the

lower valve that breaks a glass disk. Thepressure at the perforations is droppedto zero and the surge from the formationcleans out the debris. The surge issafely contained by the upper surge valve.After surging, the tubing can be pres-sured to actuate the cutter in the uppervalve that breaks a glass disk allowingthe tubing to be safely circulated.

FEATURES/BENEFITS• Surge safely contained in tubing• High pressure glass disk• No rotation required• Full opening

MODEL “F”™

CIRCULATING SUBProduct No. 675-08The Model “F” Circulating Sub providesa means of pumping open drain or circu-lation ports in the tubing by dropping aball from surface. The sleeve valve ispressure balanced with the shear valuebeing determined by the number of shearscrews installed. Available in 2-3/8"(60,33 mm) and 2-7/8" (73,03 mm) sizes.

Model “D” SurgeValve SystemProduct Nos.

714-03 & 714-04

Model “A” DualSurge System

w/ “EA” RetrievamaticProduct No. 714-09

Model “F”Circulating Sub

Product No. 675-08

Model “A” UpperSurge Valve

Product 714-19


12/55

12


MODEL “B”™

RETRIEVAMATIC/HURRICANE PLUG

Product No. 407-09Designed for emergencies that force tem-porary well shutdowns, it seals off the

casing string while the drillpipe hangs offbottom. Saving installation time, the

entire drillstring need not be pulled toinstall the plug. The Hurricane Plugoffers a choice of three drillpipe plugging

systems, depending on the well configu-rations and weather conditions. A unique

sub equalizes any pressure buildup be-fore the plug is retrieved.

The Hurricane Plug is basically a

Retrievamatic cementer and can doubleas a squeeze tool or as a plug to isolate

the casing when changing wellheads.The tool sets with right-hand rotation,

using pipe weight for initial packoff.

Model “B” Retrievamatic/Hurricane Plug

Product No. 407-09


around and through the tool while run-ning in — straight pick-up equalizespressure across hold-down buttons

instantly• Proven face-seal unloader controls the

bypass, eliminating the need for me-chanical locks and rotation — the by-

pass, running completely through thepacker, isolates buttons from tubingpressure surges

• Hold-down buttons maintain packoffduring high-pressure operations from

below• Rocker slips set with only 3/4 turn;

straight pick-up to retrieve

* For Specification Guide, see page 14.


13/55

13


Model “J” Retrievamatic/Hurricane Plug

Product No. 407-14

Model “L” Retrievamatic/Hurricane Plug

Product No. 407-18

MODEL “J”™ & MODEL “L”™

RETRIEVAMATIC/HURRICANE PLUGS

Product Nos. 407-14 & 407-18The Model “J” Retrievamatic has a J-

shaped control slot in the bottom thatautomatically re-positions the tool to therun-in position when it is picked up; no

rotation of the tool is required to go backdownhole.

The Model “J” Plug is designed to berun in conjunction with hydraulic and

mechanical-set liner hangers. Runningthe Model “J” in the string above the linerhanger allows the liner to be set and the

liner top to be tested and/or squeezedimmediately following primary cement-

ing operations. The Model “J” is alsosuitable for use in heavy duty cementer

or in hurricane plug applications.The Model “L” Retrievamatic has an

L-shaped control slot in the bottom thatrequires no rotation to reset when mov-ing up hole. However, it does require

rotation to reposition it back to the run-inposition. It is for operations where it is

desirable to be able to pick up and re-main in the “ready to set” position.

The “J” & “L” are available for casingsizes 5-1/2" (139,7 mm) to 16" (406,4 mm) and offer no 8 rd connections on the

Retrievamatic or on lift subs.


around and through the tool while run-ning in — straight pick-up equalizespressure across hold-down buttons

instantly• Proven face-seal unloader controls the

bypass, eliminating the need for

mechanical locks and rotation• The bypass, running completely

through the packer, isolates buttonsfrom tubing pressure surges

• Hold-down buttons maintain packoffduring high-pressure operations from

below

* For Specification Guide, see page 14.


14/55

14


Casing Packing Packing Slips & Buttons Range

Weight Tool Gauge, Guide Element Element Preferred Absolute

OD T&C Size Ring OD ‡ OD Spacer OD ‡ Min Max Min• Max


4-1/2 114,3 9.5-13.5 14,1-20,1 43A 3.771 95,78 3.625 92,08 3.734 94,84 3.910 99,31 4.090 103,89 3.810 96,77 4.090 103,89

5 127 15-18 22,3-26,8 43B 4.125 104,79 3.937 100,00 3.937 100,00 4.250 107,95 4.408 111,96 4.126 104,80 4.409 111,99

11.5-15* 17,1-22,3 43C 4.250 107,95 4.156 105,56 4.125 104,78 4.408 111,96 4.560 115,82 4.274 108,56 4.561 115,85

26 38,7

5-1/2 139,7 20-23 29,8-34,2 45A2 4.500 114,3 4.375 111,13 4.500 114,3 4.625 117,48 4.778 121,36 4.484 113,89 4.950 125,73

15.5-20* 23,1-29,8 45A4 4.641 117,88 4.778 121,36 4.950 125,73

13-15.5 19,3-23,1

5-3/4 146,05 22.5 33,5 45B 4.781 121,44 4.687 119,05 4.781 121,44 4.950 125,83 5.190 131,83 4.764 121,01 5.190 131,83

26 38,7

6 152,4 20-23 29,8-34,2 45C 5.062 128,57 4.937 125,40 5.062 128,57 5.191 131,85 5.390 136,91 5.000 127,0 5.390 136,91

15-18 22,3-26,8 45D 5.156 130,96 5.391 136,93 5.560 141,22 5.136 130,45 5.560 141,22

34 50,6 45E2 5.406 137,31 5.250 133,35 5.406 137,31 5.561 141,25 5.609 142,47 5.386 136,80 5.791 147,09

6-5/8 168,28 28-32 41,7-47,6 45E4 5.484 139,29 5.610 142,49 5.791 147,09

24-29 35,7-43,2 45F 5.625 142,88 5.609 142,47 5.761 146,33 5.921 150,39 5.632 143,05 5.941 151,16

24 35,7 47A2 5.656 143,66 5.830 148,08 5.937 150,80

7 177,8 38 56,5 5.500 139,7 5.656 143,66 5.597 142,16 6.135 155,83

6-5/8 168,28 17-20 25,3-29,8 47A4 5.812 147,62 5.938 150,83 6.135 155,83

32-35 47,6-52,1

7 177,8 26-29 38,7-43,2 47B2 5.968 151,59 5.750 146,05 5.968 151,59 6.136 155,85 6.276 159,41 5.861 148,87 6.538 166,07

*20-26 29,8-38,7 47B4 6.078 154,38 6.276 159,41 6.456 163,98

17-20 25,3-29,8 47C2 6.266 159,16 6.125 155,58 6.250 158,75 6.456 163,98 6.578 167,08 6.297 159,94 6.884 174,85

33.7-39 50,1-58,0 47C4 6.453 163,91 6.579 167,11 6.797 172,64

7-5/8 193,68 24-29.7 35,7-44,2 47D2 6.672 169,47 6.500 165,1 6.671 169,44 6.798 172,67 7.025 178,44 6.545 166,24 7.132 181,15

20-24 29,8-35,7 47D4 6.812 173,02 7.025 178,44 7.125 180,98

44-49 65,5-72,9 49A2 7.312 185,72 7.000 177,8 7.312 185,72 7.511 190,78 7.687 195,25 7.423 188,54 8.060 204,72

8-5/8 219,08 32-40 47,6-59,5 49A4 7.531 191,29 7.688 195,28 7.921 201,19

20-28 29,8-41,7 49B 7.781 197,64 7.500 190,5 7.781 197,64 7.922 201,22 8.191 208,05 7.919 201,14 8.255 209,68

47-53.5 69,9-79,6 51A2 8.218 208,74 7.937 201,60 8.218 208,74 8.343 211,91 8.681 220,50 8.117 206,17 8.934 226,92

9-5/8 244,48 40-47 59,5-69,9 51A4 8.437 214,30 8.681 220,50 8.835 224,40

29.3-36 43,6-53,6 51B 8.593 218,26 8.375 212,73 8.593 218,6 8.836 224,43 9.063 230,20 8.539 216,89 9.063 230,20

65.7-81 97,8-120,5 53A2 9.000 228,6 8.875 225,43 9.000 228,6 9.094 230,99 9.560 242,82 9.000 228,6 9.903 251,54

10-3/4 273,05 55.5-60.7 82,6-90,3 53A4 9.375 238,13 9.504 241,40 9.760 247,90 9.392 238,56 10.020 254,51

45.5-51 67,7-75,9 53A6 9.625 244,48 9.250 234,95 9.375 238,13 9.850 250,19 9.950 252,73

32.75-40.5 48,7-60,3 53B 10.050 255,27 10.192 258,88 9.642 244,91 10.270 260,86

11-3/4 298,45 65-80.5 96,7-119,8 5 4A 10.125 257,18 10.000 254 10.125 257,18 10.406 264,31 10.682 271,32 10.250 260,35 10.711 272,06

38-60 56,5-89,3 5 4B 10.250 260,35 10.187 258,75 10.772 273,61 11.150 283,21 10.612 269,54 11.313 287,35

13-3/8 339,73 77-102 114,6-151,8 55A 11.625 295,28 11.625 295,28 11.625 295,28 11.733 298,02 12.275 311,79 11.633 295,48 12.464 316,59

48-72 71,4-107,1 5 5B 12.125 307,98 11.812 300,02 12.191 309,65 12.715 322,96 12.133 308,18 12.800 325,12

146 217,2 57A2 13.900 353,06 13.900 353,06 — — 14.000 355,6 14.300 363,22 14.000 355,6 14.300 363,22

16 406,4 128 190,5 57A4 14.120 358,65 14.000 355,6 — — 14.250 361,95 14.500 368,3 14.250 361,95 14.500 368,3

109 162,2 57A6 14.250 361,95 — — 14.500 368,3 14.800 375,92 14.500 368,3 14.800 375,92

55-84 81,8-125,0 5 7B 14.750 374,65 14.500 368,3 — — 14.800 375,92 15.375 390,53 14.800 375,92 15.375 390,53

MODEL “B”™ RETRIEVAMATIC/HURRICANE PLUG, Product No. 407-09MODEL “J”™ RETRIEVAMATIC/HURRICANE PLUG, Product No. 407-14MODEL “L”™ RETRIEVAMATIC/HURRICANE PLUG, Product No. 407-18

SPECIFICATION GUIDE

* This size may be set in this weight casing in certain circumstances such as mixed strings or unusual hole conditions; however, the other size listed for this weight is recommended andshould be run where possible.

‡ lt may be necessary to turn OD of gauge ring, guide ring, and packing element spacers when running in minimum ID casing.• This dimension is only for guidance in situations where there may be restricted diameters the tool has to pass. In some sizes the slips are bottomed out and will not set without being

damaged.


15/55

15


TWIN-THREAD SAFETY JOINTProduct No. 441-35

The Twin-Thread Safety Joint is a right-

hand release safety joint designed toallow removal of the drillpipe or tubingfrom its position above the Retrievamatic/

Hurricane Plug by right-hand rotation.

SAFETY JOINT OVERSHOTProduct No. 441-90

The Safety Joint Overshot is used inconjunction with the twin-thread safety joint to allow the twin-thread safety joint

to be re-engaged by right-hand rotation.

ROTATIONALEQUALIZING SUBProduct No. 407-90

The Rotational Equalizing Sub is a valve

designed for use in plugging and equal-izing drillpipe or tubing above and belowthe Retrievamatic/Hurricane Plug.

MODEL “FWG”™

BLANKING PLUGProduct No. 806-88

Removal of the Model “FWG” BlankingPlug (an integral part of the rotational

equalizing sub) allows wireline opera-tions to be performed through the Hurri-cane Plug.

MODEL “P-2”™ SET-DOWNUNLOADING SUBProduct No. 671-03

The Model “P-2” Set-Down UnloadingSub is used to equalize tubing-annulus

pressure when using a set-down packer.A face-type seal prevents communica-tion between the tubing and annulus

when the sub is in the closed position;the sub is held open or closed by collet

fingers. Since the sub is essentiallypressure balanced, normal set-down

weight required for operation of the toolrun below the sub is sufficient to maintain

closed position when run with the propersize tubing.

Safety Joint Overshot

Product No. 441-90

Twin-Thread Safety Joint

Product No. 441-35

Model “FWG” Blanking PlugProduct No. 806-88

Rotational Equalizing SubProduct No. 407-90

Model “P-2” Set-Down Unloading SubProduct No. 671-03


16/55

16


MODEL “C-1”™ & “C-2”™ FULL-BORERETRIEVABLE CEMENTERProduct No. 410-01

This is a full-opening, upstrain packer used forsqueeze cementing, casing testing, formation frac-turing, and high-pressure acidizing with subse-

quent testing. It is particularly useful when set-down weight is limited. Running with the, Model

“R” ™ Upstrain Unloading Sub (Product No. 675-05) allows equalization of tubing and annuluspressure; testing of the run-in string is possible

with the Model “N” ™ Full-Bore Tubing Tester(Product No. 672-01).

FEATURES/BENEFITS• Opposing rocker-type slips enable it to remain

packed off during pressure reversals, holdingagainst pressure from above or below

• Packing element allows circulation with upperslips set, packing off when tubing is raised and

upstrain applied

MODEL “R-2”™ UPSTRAINUNLOADING SUBProduct No. 675-05

The Model “R-2” Upstrain Unloading Sub is de-signed to equalize tubing and annulus pressure

above the Full-Bore Cementer. It is a face seal

unloader that closes when tension is applied andopens with set-down weight. The unloader maybe run in either the open or closed position and

then opened and closed as many times as neces-sary. Torque is transmitted through the unloaderby means of a key.

FEATURES/BENEFITS• Unloads pressure from either direction• Easy to operate

MODEL “N”™ FULL-BORETUBING TESTER

Product No. 672-01The Model “N” Full-Bore Tubing Tester is de-

signed to close off the tubing string, providing ameans of testing the run-in string. It is run above

the full-bore and unloader. The flapper valve inthe tester is closed with a combination of right-

hand rotation and set-down.

FEATURES/BENEFITS• Allows testing of workstring

Model “R” UpstrainUnloading Sub

Product No. 675-05

Model “N” Full-BoreTubing Tester

Product No. 672-01

Model “C-1” Full-BoreRetrievable Cementer

Product No. 410-01


17/55

17


MODEL, “C-1” & “C-2” FULL-BORE RETRIEVABLE CEMENTERPRODUCT NO. 410-01

SPECIFICATION GUIDE

Casing Gauge & Slip Range Packing Threads Box Up MinimumGuide

Preferred

AbsolutePacking Element & Bore Through

Weight Cementer Rlng Element Spacer Box Down Cementer

OD T&C Size OD Min Max Min Max OD OD In. In.

In. mm lb/ft kg/m In. mm In. mm In. mm In. mm In. mm In. mm In. mm mm mm

4-1/2 114,3 9.5-13.5 14,1-20,1 43A 3.771 95,78 3.910 99,31 4.154 105,51 3.850 97,79 4.216 107,09 3.625 92,08 3.771 95,78

5* 127 21* 31,2 3.937 100,00

18* 26,8 43B 4.062 103,17 4.155 105,94 4.408 111,96 4.154 105,51 4.408 111,96 3.938 100,03 3.937 100,00

5 127 15 22,3 4.125 104,78

11.5-13 17,1-19,3 43C 4.250 107,95 4.409 111,99 4.560 115,82 4.276 108,61 4.560 115,82 4.156 105,56 4.125 104,78

20-23 29,8-34,2 45A 4.500 114,3 4.625 117,48 4.953 125,81 4.610 117,09 4.953 125,81 4.375 111,13 4.500 114,3

5-1/2 139,7 15.5-17 23,1-25,3 4.641 117,88

13-15 19,3-22,3 45B 4.781 121,44 4.954 125,83 5.190 131,83 4.950 125,73 5.190 131,83 4.688 119,08 4.781 121,44 2 -3 /8 O D E U 1. 81 3 - 1. 96 8* *

5-3/4 146,05 19.5-22.5 29,0-33,5 60,33 46,05 - 49,99

14 20,8 45C 5.062 128,57 5.191 131,85 5.390 136,91 5.160 131,06 5.424 137,77 8 Rd

20-23 29,8-34,2 4.938 125,43 5.062 128,57

6 152,4 17-18 25,3-26,8 45D 5.156 130,96 5.391 136,93 5.560 141,22 5.248 133,30 5.560 141,22

14-16 20,8-23,8 5.312 134,92

34 50,6 45E 5.406 137,31 5.561 141,25 5.791 147,09 5.561 141,25 5.791 147,09

6-5/8 168,28 28-32 41,7-47,6 5.484 139,29 5.250 133,35 5.406 137,31

24-29 35,7-43,2 45F 5.588 141,94 5.761 146,33 5.921 150,39 5.695 144,65 6.118 155,40

6-5/8 168,28 24-26.5 35,7-39,4 5.656 143,66

7 177,8 38-40 56,5-59,5 47A 5.830 148,08 6.100 154,94 5.830 148,08 6.184 157,07 5.500 139,7 5.656 143,66

6-5/8 168,28 20-22 29,8-32,7 5.812 147,62

7 177,8 32-35 47,6-52,1

6-5/8 168,28 17 25,3 5.968 151,59

28-30 41,7-44,6 47B 6.101 154,97 6.530 165,86 6.094 154,79 6.538 166,07 5.750 146,05 5.968 151,59 2.375

7 177,8

23-26 34,2-38,7

6.078 154,38 60,33

20-23 29,8-34,2 47BC 6.210 157,73 6.210 157,73

17 25,3 6.281 159,54 6.531 165,89 6.700 170,18 6.531 165,89 6.875 174,63 6.125 155,58 6.281 159,54

33.7-39 50,1-58,0 47C 6.453 163,91 6.780 172,21 6.453 163,91

7-5/8 193,68 26.4-29.7 39,3-44,2 47D 6.672 169,47 6.781 172,24 7.125 180,98 6.770 171,96 7.125 180,98 6.500 165,1 6.672 169,47 2-7/8 OD EU

20-24 29,8-35,7 6.812 173,02 73,03

49 72,9 7.312 185,72 8 Rd

44 65,5 49A 7.375 187,33 7.500 190,5 7.937 201,60 7.451 189,26 7.937 201,60 7.000 177,8 7.312 185,72

8-5/8 219,08 36-40 53,6-59,5 7.531 191,29

32 47,6 7.625 193,68

24-28 35,7-41,7 49B 7.781 197,64 7.968 202,39 8.375 212,73 7.906 200,81 8.437 214,30 7.500 190,5 7.781 197,64 2.468

9 228,6 34-40 50,6-59,5 7.968 202,39 62,69

53.5 79,6 51A 8.218 208,74 8.375 212,73 8.781 223,04 8.250 209,55 8.813 223,85 7.938 201,63 8.218 208,74

9-5/8 244,48 43.5-47 64,7-69,9 8.437 214,30

40 59,5 51B 8.593 218,26 8.718 221,44 9.125 231,78 8.688 220,68 9.125 231,78 8.375 212,73 8.593 218,26 29.3-36 43,6-53,6 8.750 222,25

3-1/2 OD EU 8 Rd10-3/4 273,05 32.7-55.5 48,7-82,6 53 9.440 239,78 9.750 247,65 10.192 258,88 9.584 243,43 10.198 259,03 9.250 234,95 9.375 238,13 88,9

& 2-7/8 OD EU 8 Rd73,03

4-1/2 OD NU 4.00011-3/4 298,45 38-60 56,5-89,3 54 10.250 260,35 10.772 273,61 11.150 283,21 10.612 269,54 11.313 287,35 10.000 254 10.187 258,75 114,3 101,6

8 Rd & 4-1/2 OD114,3

13-3/8 339,73 48-72 71,4-107,1 55 11.875 301,63 12.347 313,61 12.715 322,96 12.177 309,30 12.897 327,58 11.625 295,28 11.812 300,02 8 Rd Lg casing thd

* For combination strings of 5" (127,0 mm) 18 lb (26,8 kg/m) and 21 lb (31,2 kg/m) casing, use Size 43B Slips and Packing Element with gauge and guide rings turned to 4.000"(101,61 mm) OD.** Larger bores available when ordered only.


18/55

18


FEATURES/BENEFITS• Circulation passage through valves al-

lows fluid to bypass during running/

retrieving, reducing swabbing• Opposed rocker slips prevent move-ment either up or down, depending onthe direction of the differential pressure

MODEL “C”™

RETRIEVABLE BRIDGE PLUGProduct No. 677-01

A dependable plug that holds pressurefrom above or below, the Model “C” isused for acidizing, formation fracturing,

and temporary pressure containment.This plug uses differential pressure

from above or below to achieve andmaintain packoff. Once the plug hasbeen run to the desired depth and re-

leased, it sets automatically and sealsagainst pressure differential from either

direction.Simple to pick up and relocate, it is

ideal for selective isolation and fractur-

ing, acidizing, or testing of several zonesin one round trip when used with a re-

trievable cementer. It is run and retrievedwith the Model “H” ™ Washover Type

Retrieving Head (Product No. 677-71).

Bridge plugreleased, interval

straddled, fracturingor acidizing being

performed

MODEL “H-1”™ RETRIEVABLEBRIDGE PLUGProduct No. 677-06

The Model “H-1” Retrievable Bridge Plugis comparable to the Model “C” Retriev-able Bridge Plug in performance, applica-tion and operation. In addition, it incorpo-rates a hydraulically balanced lower valve

and is applicable to well conditions whereflow of either gas or fluid from below theplug is anticipated. When the plug isrelocated or pulled from the well, pres-sure from below is relieved by holding thevalve open. (Tool is not shown.)

Tools run intogether,

connected byretrieving head

Swabbing andtesting, pressure

differential reversed

Bridge plug pickedup, being moved to

next interval

Model “C” RetrievableBridge Plug

Product No. 677-01


19/55

19


MODEL “H”™

WASHOVER-TYPERETRIEVING HEAD

Product No. 677-71The Model “H” Washover-Type Retriev-ing Head, used with the Model “C” ™ and

“H-1”™ Retrievable Bridge Plugs, allowswashover operations with the mill shoe

guide and makes it easier to removesand and debris from the top of thebridge plug.

MODEL “C” RETRIEVABLE BRIDGE PLUGPRODUCT NO. 677-01

SPECIFICATION GUIDE

SEALER BALL CATCHER(for Models “C”™ and “H-1”™

Retrievable Bridge Plugs)

Product No. 677-94The Sealer Ball Catcher is a slotted

basket threaded to the upper valve cageof either Model “C” or “H-1” Bridge Plug.

Its volume is adequate to catch the aver-age number of sealer balls used onacidizing jobs only. The catcher elimi-

nates the balls from accumulating on topof the retrievable bridge plug, which

could cause difficulties in retrieving. (Toolis not shown.)

Model “H” Washover-TypeRetrieving Head

Product No. 677-71

Casing Gage Ring Slip Range SizeBridge or Thimble Packer Cup Preferred Absolute Drag Retrieving

OD Plug OD Commodity Min Max Min Max Spring Head

In. lb/ft Size In. No. In. In. In. In. Size In.mm kg/m mm mm mm mm mm mm

2-7/8 6.4 - 6.5 28A 2.218 01-51551-00 2.223 2.441 2.213 2.53773,03 9,5 - 9,7 56,34 56,46 62,00 56,21 64,44

4.7 - 5.6 28B 2.385 2.563 2.335 2.6597,0 - 8,3 60,58 65,10 59,31 67,54

10.2 35A 2.734 01-61509-00 2.796 2.875 2.747 2.922 — 1.31515,2 69,44 71,02 73,03 69,77 74,22 33,40

3-1/2 7.7 - 9.3 35B 2.796 2.858 2.992 2.804 3.00088,9 11,5 - 13,8 71,02 72,59 76,00 71,22 76,2

5.7 35C 2.937 01-50023-00 3.000 3.188 2.946 3.2808,5 74,60 76,2 80,98 74,83 83,319.5 41A 3.244 01-48282-00 3.364 3.548 3.244 3.563

14,1 82,40 85,45 90,12 82,40 90,50 4 12.93 — 1.900

101,6 19,2 48,26 5.65 41B 3.578 01-50061-00 3.732 3.920 3.562 3.9288,4 90,88 94,79 99,57 90,47 99,77

4-1/2 13.5 - 16.6114,3 20,1 - 24,7

9.5 - 13.5 43A 3.771 01-35917-00 3.910 4.154 3.850 4.216

14,1 - 20,1 95,78 99,31 105,51 97,79 107,09 21† 3.937‡ 10 1.90031,2 100,00 48,26

5† 18 43B 4.062 01-35026-00 4.155 4.408 4.154 4.408 or127 26,8 103,17 105,54 111,96 105,51 111,96

15 4.125 2.37522,3 104,78 60,33

11.5 - 13 43C 4.250 01-36238-00 4.409 4.560 4.276 4.560 2017,1 - 19,3 107,95 111,99 115,82 108,61 115,82

20 - 23 45A 4.500 01-36821-00 4.625 4.953 4.610 4.953 1029,8 - 34,2 114,3 117,48 125,81 117,09 125,81

5 -1/2 15.5 - 17 4.641 01-35691-00 20139,7 23,1 - 25,3 117,88

13 - 14 45B 4.781 01-39618-00 4.954 5.190 4.950 5.19019,3 - 20,8 121,44 125,83 131,83 125,73 131,83

20 - 23 45C 5.063 WV-G114-714 5.191 5.390 5.160 5.42429,8 - 34,2 128,60 131,85 136,90 131,06 137,77

6 18 45D 5.156 WV-G114-721 5.391 5.560 5.248 5.560152,4 26,8 130,96 136,93 141,22 133,30 141,22

15 5.25022,3 133,35 32 45E 5.406 WV-G115-490 5.561 5.791 5.561 5.791 30 2.375

47,6 137,31 141,25 147,09 141,25 147,09 60,33 6-5/8 28 5.484 WV-G114-962 or

168,28 41,7 139,29 24 - 29 45F 5.588 5.761 5.921 5.695 6.118 2.875

35,7 - 43,2 141,94 146,33 150,39 144,65 155,40 73,03 24 5.656 01-39535-00 10

35,7 143,66 7 38 47A 5.830 6.100 5.830 6.184

177,8 56,5 148,08 154,94 148,08 157,07 6-5/8 20 5.812 01-41179-00

168,28 29,8 147,62 7 32 - 35

177,8 47,6 - 52,16-5/8 17 5.968 01-39534-00 20

168,28 25,3 151,59 29 47B 6.101 6.530 6.094 6.538

43,2 154,97 165,86 154,79 166,07 7 23 - 26 6.078 01-37417-00

177,8 34,2 - 38,7 154,38 20 - 23 6.210 01-39727-00

29,8 - 34,2 157,73 17 47C 6.266 6.531 6.780 6.531 6.875 30

25,3 159,16 165,89 172,21 165,89 174,63 7-5/8 33.7 - 39 6.453 01-47289-00

193,68 50,1 - 58,0 163,9126.4 - 29.7 47D 6.672 01-47290-00 6.781 7.125 6.770 7.12539,3 - 44,2 169,47 172,24 180,98 171,96 180,98

40 - 49 WV-G116-11559,5 - 72,9

36 49A WV-G116-113 7.500 7.937 7.451 7.937 4053,6 190,5 201,60 189,26 201,60 8-5/8 32 7.375 WV-G116-111

219,08 47,6 187,33 28 49B 7.968 8.375 7.906 8.437 50

41,7 202,39 212,73 200,81 214,30 24 WV-G115-941

35,7 9-5/8 43.5 - 53.5 51A 8.281 01-50182-00 8.375 8.781 8.250 8.813 40 2.875

244,48 64,7 - 79,6 210,34 212,73 221,44 209,55 223,85 73,03 36 - 40 51B 8.375 WV-G110-354 8.718 9.125 8.718 9.125

53,6 - 59,5 212,73 221,44 231,78 221,44 231,78 10-3/4 32.75 - 55.5 53 9.500 WV-G113-197 9.750 10.192 9.584 10.198273,05 48,7 - 82,6 241,3 247,65 258,88 243,43 259,03 11-3/4 38 - 60 54 10.375 WV-G114-246 10.772 11.150 10.612 11.313 50298,45 56,5 - 89,3 263,53 273,61 283,21 269,54 287,35 13-3/8 68 - 72 55A 11.875 WV-G116-298 12.344 12.719 12.176 12.900339,73 101,2 - 107,1 301,63 313,54 323,06 309,37 327,66

48 - 61 55B WV-G119-23771,4 - 90,8

WeightT&C

† For combination casing strings of 5" (127 mm) 18 lbs (26,8 kg/m) and 5" (127 mm) 21 lbs (31,2 kg/m), use Size 43B Slips andGauge Ring turned to 3.937" (99,9 mm).

‡ Size 43B Gauge Ring can be turned to this diameter.


20/55

20


Model “G” Lok-SetRetrievable Bridge Plug

Product No. 677-34

Model “L” Lok-SetRetrieving Head

Product No. 677-75

MODEL “G”™ LOK-SET ®

RETRIEVABLE BRIDGEPLUG

Product No. 677-34This plug is designed for higher-pres-sure, higher-temperature applications

than the Model “C”™. Applicationsinclude multiple testing and treating

operations, selective single-zone op-erations, fracturing, acidizing, or ce-menting. It withstands high differen-

tial pressure from above or below, athigh temperatures.

FEATURES/BENEFITS• Balanced unloader remains open

while plug is engaged in the retriev-ing head — this eliminates having

to overcome pressure differentialwhile running in, packing off, or

retrieving• Triple packing element system re-

tracts completely, allowing fast,safe running and retrieving — sealstightly against high differential pres-

sure• Opposed slips prevent movement

either up or down• Circulation passage through the

plug allows fluid to bypass duringrunning or retrieving, reducing swab-bing

MODEL “L”™ LOK-SET ®

RETRIEVING HEADProduct No. 677-75

The Model “L” Lok-Set ® RetrievingHead is used for running and retriev-

ing Model “G” Lok-Set RetrievableBridge Plugs. While the retrievinghead is engaged with the bridge plug,

the balanced unloading valve, whichcontrols fluid flow through the bridge

plug, is open. When the plug sets andthe retrieving head is released, the

unloading valve is automaticallyclosed.

The retrieving head can be as-sembled with a rotating feature, mak-ing it easier to wash sand and debris

from the top of the bridge plug whenretrieving.

MODEL “GT”™ LOK-SET ®

RETRIEVABLE BRIDGEPLUG

Product No. 677-37The Model “GT” Lok-Set ® RetrievableBridge Plug is a version of the Model

“G” Lok-Set ® Retrievable Bridge Plugwhich can be positively tested from

above and below. Also, well controlcan be maintained through the tubingwhile equalizing pressure from below

the plug.Current regulations in certain drill-

ing markets require three containmentbarriers for temporary abandonment of

a well. The “GT” Lok-Set ® Retrievable

Bridge Plug provides one of those bar-riers and is the only retrievable bridge

plug that can be positively tested fromboth above and below. (Tool is not

shown.)

MODEL “LTC”™ LOK-SET ®


The Model “LTC” ™ Lok-Set ® Retriev-ing Head is used to run, set, test below,

equalize, and retrieve the Model “GT”

Lok-Set ®

Retrievable Bridge Plug orthe “FT”™ Latching Type Packer Plug.This retrieving head provides a seal

between the tubing and the unloaderon the Model “GT” Lok-Set ® Retriev-able Bridge Plug or the “FT” Latching

Type Packer Plug. (Tool is not shown.)

MODEL “LT-CT”™ LOK-SET ®


The Model “LT-CT” Lok-Set ® Retriev-

ing Head is used to run, set, test below,equalize, and retrieve the Model “GT”Lok-Set ® Retrievable Bridge Plug or

the “FT” Latching Type Packer Plug.This retrieving head provides a seal

between the tubing and the unloaderon the Model “G” Lok-Set ® Retrievable

Bridge Plug or the “F”™ Latching TypePacker Plug. The retrieving head hasa telescoping sleeve on the bottom that

permits easy washing to the top of theplug. (Tool is not shown.)


21/55

21


Packing Min MaxBridge Gauge Packing Element Collapsed Casing ID for

Weight Nom. Casing ID Plug Ring Element Spacer Dia of Slip & Drag

OD T&C Min Max Size OD OD OD Drag Block Block Travel


4-1/2 114,3 9.5 - 13.5 14,1 - 20,1 3.920 99,57 4.090 103,89 43A2 3.771 95,78 3.738 94,95 4.132 104,95

9.5 - 10.5 14,1 - 15,6 4.052 102,92 4.276 108,61 43A4 3.875 98,43 3.625 92,08 3.734 94,84 3.864 98,15 4.276 108,61

18 - 20.3 26,8 - 30,2

5 127 15 - 18 22,3 - 26,8 4.276 108,61 4.408 111,96 43B 4.125 104,78 3.938 100,03 3.938 100,03 4.124 104,75 4.458 113,23

11.5 - 15 17,1 - 22,3 4.408 111,96 4.560 115,82 43C 4.250 107,95 4.156 105,56 4.125 104,78 4.238 107,65 4.582 116,38

26 38,7

5-1/2 139,7 20 - 23 29,8 - 34,2 4.625 117,48 4.778 121,36 45A2 4.500 114,3 4.375 111,12 4.500 114,3

15.5 - 20 23,1 - 29,8 4.778 121,36 4.950 125,73 45A4 4.641 117,88 4.503 114,38 5.190 131,83

13 - 15.5 19,3 - 23,1 4.950 125,73 5.190 131,82 45B 4.781 121,44 4.688 119,08 4.781 121,44

26 38,7 6 152,4 20 - 23 29,8 - 34,2 5.191 131,85 5.390 136,90 45C 5.063 128,60 4.938 125,43 5.063 128,60 5.035 127,89 5.690 144,53

15 - 18 22,3 - 26,8 5.391 136,93 5.560 141,22 45D 5.156 130,96

34 50,6 5.561 141,25 5.609 142,47 45E2 5.406 137,31 5.250 133,35 5.406 137,31

6-5/8 168,28 28 - 32 41,7 - 47,6 5.610 142,50 5.791 147,09 45E4 5.484 139,29 5.381 136,68 5.970 151,64

24 - 28 35,7 - 41,7 5.791 147,09 5.921 150,39 45F 5.625 142,88 5.609 142,47

24 35,7 5.830 148,08 5.937 150,80 47A2 * 5.656 143,66

7 177,8 38 56,5 5.500 139,7 5.636 143,15

6-5/8 168,28 17 - 20 25,3 - 29,8 5.938 150,83 6.135 155,82 47A4 * 5.812 147,62 5.650 143,51 6.590 167,39

32 - 35 47,6 - 52,1

7 177,8 26 - 29 38,7 - 43,2 6.136 155,85 6.276 159,41 47B2* 5.968 151,59 5.750 146,05 5.948 151,08

20 - 26 29,8 - 38,7 6.276 159,41 6.456 163,98 47B4* 6.078 154,38

17 - 20 25,3 - 29,8 6.456 163,98 6.578 167,08 47C2* 6.266 159,16 6.125 155,58 6.246 158,65

33.7 - 39 50,1 - 58,0 6.579 167,11 6.797 172,64 47C4* 6.453 163,91 6.276 159,41 7.215 183,26

7-5/8 193,68 24 - 29.7 35,7 - 44,2 6.798 172,67 7.025 178,44 47D2* 6.672 169,47 6.500 165,1 6.652 168,96 20 - 24 29,8 - 35,7 7.025 178,44 7.125 180,98 47D4* 6.812 173,02

49.1 - 54 73,1 - 80,4 7.310 185,67 7.510 190,75 49A1 7.218 183,34 7.198 182,83

8-5/8 219,08 43 - 49 64,0 - 72,9 7.511 190,78 7.687 195,25 49A2 7.312 185,72 7.000 177,8 7.281 184,94 7.148 181,56 8.089 205,46

32 - 40 47,6 - 59,5 7.688 195,28 7.921 201,19 49A4 7.531 191,29

20 - 28 29,8 - 41,7 7.922 201,22 8.191 206,53 49B 7.781 197,64 7.500 190,5 7.750 196,85 7.774 197,46 8.712 221,28

71.8 106,8

58.4 - 61.1 86,9 - 90,9 8.219 208,76 8.435 214,25 51A1* 8.093 205,56 7.812 198,42 8.011 203,48

9-5/8 244,48 47 - 53.5 69,9 - 79,6 8.343 211,91 8.681 220,50 51A2* 8.218 208,74 7.937 201,60 8.204 208,38 8.086 205,38 9.158 232,61

40 - 47 59,5 - 69,9 8.681 220,50 8.835 224,40 51A4* 8.437 214,30

29.3 - 36 43,6 - 53,6 8.836 224,43 9.063 230,20 51B* 8.593 218,26 8.375 212,73 8.593 218,26

71.1 - 81 105,8-120,5 9.250 234,95 9.450 240,03 53A2* 9.000 228,6 8.875 212,73 9.000 228,6

10-3/4 273,05 55.5 - 65.7 82,6 - 97,8 9.560 242,82 9.760 247,90 53A4* 9.375 238,13 9.250 234,95 9.375 238,13 9.000 228,6 10.500 266,7

32.7 - 51 48,7 - 75,9 9.850 250,19 10.192 258,88 53B* 9.625 244,48

MODEL “G”™ LOK-SET ® RETRIEVABLE BRIDGE PLUG, PRODUCT NO. 677-34MODEL “GT”™ LOK-SET ® RETRIEVABLE BRIDGE PLUG, PRODUCT NO. 677-37

SPECIFICATION GUIDE

Sealer BallCatcher

Product No.677-95

Casing

* Model “GT” only available in these sizes at this time.

SEALER BALL CATCHER (FOR THEMODEL “G” LOK-SET™ BRIDGE PLUG)Product No. 677-95

The Sealer Ball Catcher is a slotted basket threaded to the lock nut of the Model

“G” Bridge Plug. Its volume is adequate to catch the average number of sealerballs used on acidizing jobs only. The catcher eliminates the balls from

accumulating on top of the retrievable bridge plug, which could causedifficulties in retrieving.


22/55

22


WIRELINE SETRETRIEVABLE BRIDGE PLUGProduct No. 677-32

The Wireline Set Retrievable Bridge Plugis a medium-performance retrievablebridge plug that combines the advan-

tages of tubing or sand-line retrievabilitywith the advantages of fast, accurate

electric wireline setting.The Wireline Set Retrievable Bridge

Plug can be used for any operation that

the Model “C” ™ Retrievable Bridge Plug(Product No. 677-01) is used, such as

zone isolation, formation fracturing oracidizing, and surface equipment repair,

where the accuracy of electric wireline

setting is desirable. This provides adistinct advantage in situations in which

the plug must be run and retrieved underpressure, as it can be lubricated in and

out of the well, eliminating the necessityof snubbing tubing or killing the well.

This plug is retrieved with the Model“M”™ Washover Retrieving Head(Product No. 677-76).

Retrieving withModel “M” Retrieving Head

Product No. 677-76

Running in withWireline Adapter KitProduct No. 438-27

Wireline SetRetrievable Bridge Plug

Product No. 677-32

Model “M” WashoverRetrieving Head

Product No. 677-76


23/55

23


WIRELINE SET RETRIEVABLE BRIDGE PLUGPRODUCT NO. 677-32

SPECIFICATION GUIDE

Gauge Packing Packing Slip Range Casing Packer Ring Element Element Preferred Absolute

OD Weight Size OD OD Spacer OD Min Max Min Max


4-1/2 114,3 9.5 - 13.5 14,1 - 20,1 43A 3.771 95,78 3.625 92,08 3.771 95,78 3.910 99,31 4.090 103,89 3.687 93,65 4.207 106,86

5 127 15 - 18 22,3 - 26,8 43B 4.125 104,78 3.938 100,01 4.125 104,78 4.250 107,95 4.408 111,96

11.5 - 15 17,1 - 22,3 43C 4.250 107,95 4.156 105,57 4.250 107,95 4.408 111,96 4.560 115,82 4.062 103,17 4.582 116,38

26 38,7

5-1/2 139,7 20 - 23 29,8 - 34,2 45A2 4 .500 114,3 4.75 120,65 4.500 114,3 4.625 117,48 4.778 121,36

15.5 - 20 23,1 - 29,8 45A4 4 .641 117,88 4.778 121,36 4.950 125,73 4.437 112,70 5.221 132,61

13 - 15.5 19,3 - 23,1 45B 4.781 121,44 4.688 119,06 4.781 121,44 4.950 125,73 5.190 131,82

26 38,7

6 152,4 20 - 23 29,8 - 34,2 45C 5.062 128,57 4.938 125,41 5.062 128,57 5.191 131,85 5.390 136,90

15 - 18 22,3 - 26,8 45D 5.156 130,96 5.392 136,96 5.560 141,22 5.000 127 5.784 146,91

34 50,6 45E 5.406 137,31 5.250 133,35 5.406 137,31 5.561 141,25 5.609 142,46

6-5/8 168,28 24 - 32 35,7 - 47,6 45F 5.484 139,29 5.610 142,49 5.921 150,39 5.437 138,10 6.221 158,01

17 - 24 25,3 - 35,7 45G 5.781 146,84 5.688 144,46 5.781 146,84 5.922 150,42 6.135 155,83

24 35,7 47A2 5 .656 143,66 5.830 148,08 5.937 150,80

7 177,8 38 56,5 5.500 139,7 5.656 143,66

6-5/8 168,28 17 - 20 25,3 - 29,8 47A4 5 .812 147,62 5.930 150,62 6.135 155,83 5.562 141,27 6.665 169,29

32 - 35 47,6 - 52,1

7 177,8 26 - 29 38,7 - 43,2 47B2 5 .968 151,59 5.750 146,05 5.968 151,59 6.136 155,85 6.276 159,41

23 - 26 34,2 - 38,7 47B4 6 .078 154,38 6.276 159,41 6.366 161,70

17 - 20 25,3 - 29,8 47C2 6 .266 159,16 6.125 158,75 6.266 159,16 6.456 163,98 6.578 167,08

33.7 -39 50,1 - 58,0 47C4 6 .453 163,91 6.579 167,11 6.797 172,64 6.200 157,48 7.303 185,50

7-5/8 193,68 24 - 29.7 35,7 - 44,2 47D2 6 .672 169,47 6.500 165,1 6.672 169,47 6.798 172,67 7.025 178,44

20 - 24 29,8 - 35,7 47D4 6 .812 173,02 7.025 178,44 7.125 180,98

8-5/8 219,08 20 - 28 29,8 - 41,7 49 7.796 198,02 7.500 190,5 7.796 198,02 7.922 201,22 8.191 208,05 7.250 184,15 8.276 210,21


24/55

24


MODEL “WG”™ WIRELINE SET

RETRIEVABLE BRIDGE PLUGProduct No. 677-39

The Model “WG” Wireline Set Retriev-able Bridge Plug is for applications wherethe speed and accuracy of wireline set-

ting is desired and where high pressuresor temperatures will be encountered.

The Model “WG” uses proven parts andtechnology from the Model “G” Lok-Set ®

Retrievable Bridge Plug (Product No.677-34). Typical applications for thisplug are fracturing, acidizing, and test-

New!

ing. The plug is set on wireline using a

Wireline Adapter Kit (Product No. 438-46) and retrieved with a Model “MWG”™

Retrieving Head (Product No. 677-76)

on either tubing, drillpipe or coiledtubing.

FEATURES/BENEFITS• High performance pressure rating

• Proven triple packing element system• Opposing slips hold in both directions

• Able to handle multiple pressurereversals

Gauge Packing Packing Slip Range

Casing Packer Ring Element Element Preferred Absolute

OD Weight Size OD OD Spacer OD Min Max Min Max

In. lb/ft In. In. In. In. In. In. In.mm mm mm mm mm mm mm mm mm

4-1/2 11.6- 13.5 43A2 3.771 3.771 3.910 4.000114,3 17,3 - 20,1 45,78 95,78 99,31 101,6

9.5 - 10.5 43A4 3.875 3.625 3.875 4.001 4.184 3.687 4.20714,1 - 15,6 98,43 92,08 98,43 101,63 106,27 93,65 106,86

20.3 - 24.230,2 - 36,0

5 15 - 18 43B 4.125 3.938 4.125 4.250 4.408127 22,3 - 26,8 104,78 100,03 104,78 107,95 111,96

11.5 - 15 43C 4.250 4.156 4.250 4.408 4.560 4.062 4.582

17,1 - 22,3 107,95 105,56 107,95 111,96 115,82 103,17 116,38

2638,7

20 - 23 45A2 4.500 4.375 4.500 4.625 4.7785-1/2 29,8 - 34,2 114,3 111,13 114,3 117,48 121,36

139,7 15.5 - 20 45A4 4.641 4.778 4.950 4.437 5.22123,1 - 29,8 117,88 121,36 125,73 112,70 132,61

13 - 15.5 45B 4.781 4.688 4.781 4.950 5.19019,3 - 23,1 121,44 119,08 121,44 125,73 131,83

6 26152,4 38,7

6-5/8 24 47A2 5.656 5.656 5.82

remdial & stimulation

Documents