rego regulators 2011 · rego® regulators 2011 n first stage n compact twin stage n compact second...
TRANSCRIPT
RegO® Regulators 2011n First Stagen Compact Twin Stagen Compact Second Stagen Second Stagen High Pressure Industrial
Industrial valves and regulators with 10 years warranty
The expected service life of a ECII/REGO® regulator (excluding single stage) manufactured after 1995 is 25 years on condition that all of our recommendations are followed.
www.rego-europe.de
Page 2
www.rego-europe.de
Page 3
Instructions
Do You Care About What’s In Your
Propane Regulator?
WE DO.And we know how important it is to select the highest
quality components from suppliers you
know and trust. Suppliers who are not
always the cheapest but are always
the best.Together with our
own high-end production facilities we are able to keep
supplying you the best-built
LPG regulators.
We will provide 10 years warranty
on all REGO Products (terms and conditions apply)
www.rego-europe.de
Page 4
Instructionswww.rego-europe.de
Page 5
Instructions
www.rego-europe.de
Page 6
Instructionswww.rego-europe.de
Page 7
Instructions
www.rego-europe.de
Page 8
Instructionswww.rego-europe.de
Page 9
Instructions
www.rego-europe.de
Page 10
www.rego-europe.de
Page 11
RegO® Compact First Stage Regulators LV3403TRLV3403TR
ApplicationIdeal for use as a fi rst stage regulator on any domestic LPG installations requiring up to 32 kg/h per hour. The regulator is factory set to reduce container pressure to an intermediate pressure of approximately 0,7 bar.
FeaturesCompact design can be connected to a service ¢valve using either a POL adapter or a RegO Products pigtail.Large threaded 3/8” F.NPT bonnet vent can be ea- ¢sily piped-away underground installations without the need of glue kits or extra adapters.Non adjustable. ¢Large fl ow orifi ce resists freeze-ups due to water ¢concentration in LPG vapourDesign provides for good fl ow regulation at both ¢high and low container pressures.Built in relief valve and travel stop comply with ¢NFPA 58 over pressure requirements.Incorporates 1/8” F.NPT downstream pressure tap ¢for an easy inline check of the regulator’s delivery pressure.Moulded diaphragm provides an o-ring type seal ¢between the body and bonnet.Body and bonnet are assembled in the USA using ¢the unique, patented RegUlok seal system.Fully painted in brilliant red for complete corrosion ¢protection.Mounting bracket available as an accessory: part ¢number 2302-31.
MaterialsBody Zinc
Bonnet Zinc
Spring Steel
Seat Disc Resilient Rubber
Diaphragm Integrated Fabric and Synthetic Rubber
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV3403TR series are UL approved.
Ordering Information
Part Number Inlet Connection
Outlet Connection Orifi ce Size Factory Delivery
Pressure Bonnet Vent Position Approximate Vapour Capacity
LV3403TR ¼” F.NPT ½” F.NPT 6,3 mm 0,7 bar Over Outlet 32 kg/h
LV3403TRV9 ¼” F.NPT ½” F.NPT 6,3 mm 0,7 bar Opposite Gauge port 32 kg/h
LV3403UR ¼” F.NPT ½” F.NPT 6,3 mm 1 bar Over Outlet 40 kg/h
NEWNon freezing regulator
in all conditions
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV3403TR
RegO® Compact First Stage Regulators LV3403VRLV3403VR
ApplicationIdeal for use as a fi rst stage regulator on any domesticLPG installations requiring up to 45 kg/h per hour.The regulator is factory set to reduce container pressureto an intermediate pressure of approximately 1,5 bar.
FeaturesCompact design can be connected to a service ¢valve using either a POL adapter or a RegO Products pigtail.Large threaded 3/8” F.NPT bonnet vent can be ea- ¢sily piped-away underground installations without the need of glue kits or extra adapters.Non adjustable. ¢Large fl ow orifi ce resists freeze-ups due to water ¢concentration in LPG vapourDesign provides for good fl ow regulation at both ¢high and low container pressures.Built in relief valve and travel stop comply with ¢NFPA 58 over pressure requirements.Incorporates 1/8” F.NPT downstream pressure tap ¢for an easy inline check of the regulator’s delivery pressure.Moulded diaphragm provides an o-ring type seal ¢between the body and bonnet.Body and bonnet are assembled in the USA using ¢the unique, patented RegUlok seal system.Fully painted in brilliant red for complete corrosion ¢protection.Mounting bracket available as an accessory: part ¢number 2302-31.
MaterialsBody Zinc
Bonnet Zinc
Spring Steel
Seat Disc Resilient Rubber
Diaphragm Integrated Fabric and Synthetic Rubber
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV3403VR series are UL approved.
Ordering Information
Part Number Inlet Connection
Outlet Connection Orifi ce Size Factory Delivery
Pressure Bonnet Vent Position Approximate Vapour Capacity
LV3403VR ¼” F.NPT ½” F.NPT 6,3 mm 1,5 bar Over Outlet 45 kg/h
LV3403VR9 ¼” F.NPT ½” F.NPT 6,3 mm 1,5 bar Opposite Gauge port 45 kg/h
NEWNon freezing regulator
in all conditions
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV3403VR
www.rego-europe.de
Page 12
www.rego-europe.de
Page 13
RegO® Compact First Stage Regulators LV3403TRH (L) Series with BSP Threads
LV3403TRH (L) Series
ApplicationIdeal for use as a fi rst stage regulator on any domestic LPG installations requiring up to 45 kg/h per hour. The regulator is factory set to reduce container pressure to an intermediate pressure of approximately 0,45 or 1,5 bar.
FeaturesCompact design can be connected to a service ¢valve using either a POL adapter or a RegO Products pigtail.Large threaded 3/8” F.NPT bonnet vent can be ea- ¢sily piped-away underground installations without the need of glue kits or extra adapters.Non adjustable. ¢Large fl ow orifi ce resists freeze-ups due to water ¢concentration in LPG vapourDesign provides for good fl ow regulation at both ¢high and low container pressures.Built in relief valve and travel stop comply with ¢NFPA 58 over pressure requirements.Incorporates 1/8” F.NPT downstream pressure tap ¢for an easy inline check of the regulator’s delivery pressure.Moulded diaphragm provides an o-ring type seal ¢between the body and bonnet.Body and bonnet are assembled in the USA using ¢the unique, patented RegUlok seal system.Fully painted in brilliant red for complete corrosion ¢protection.
Mounting bracket ¢available as an accessory: part number 2302-31.
MaterialsBody Zinc
Bonnet Zinc
Spring Steel
Seat Disc Resilient Rubber
Diaphragm Integrated Fabric and Synthetic Rubber
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use.
Ordering Information
Part Number Inlet Connection
Outlet Connection Orifi ce Size Factory Delivery
Pressure Bonnet Vent Position Approximate Vapour Capacity
LV3403TRH ¼” F-BSP ½” F-BSP 6,3 mm 1,5 bar Over Outlet 45 kg/h
LV3403TRHV9 ¼” F-BSP ½” F-BSP 6,3 mm 1,5 bar Opposite Gauge port 45 kg/h
LV3403TRL ¼” F-BSP ½” F-BSP 6,3 mm 0,45 bar Over Outlet 45 kg/h
LV3403TRLV9 ¼” F-BSP ½” F-BSP 6,3 mm 0,45 bar Opposite Gauge port 45 kg/h
NEWNon freezing regulator
in all conditions
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV3403TRH (L) Series
RegO® New 7525B34 Twin Stage Automatic Changeover Regulator for LP-Gas
7525B34
ApplicationThis combination automatic change-over /two stage regulator is suitable for homes, mobile homes, cot-tages, construction and other portable installations utilizing two or more cylinders. Empty containers may be replaced without interrupting customer’s gas service.
FeaturesAutomatic changeover switches from “service” to ¢“reserve” cylinder automatically without inter-rupting gas service.With 1 bar inlet pressure, the regulator is designed ¢to not pass more than 137 mbar downstream with the seat disc removed.Incorporates a integral relief valve on second stage. ¢Unique bonnet vent profi le on second stage mini- ¢mizes vent freeze over when properly installed.Compact design saves space allows for easy ¢installation.Allows “reserve” cylinder to supplement the fl ow of ¢gas from the “service” cylinder during extreme load or severe cold conditions.Indicator gauge and changeover knob are integral ¢to the fi rst stage.Second stage pressure tap plug can be removed ¢with a 3/16” hex Allen wrench.
Part Number Inlet Connection
Outlet Connection
FactoryDelivery Pressure
AdjustmentRange 2nd
Stage
Bonnet Vent Position 2nd
Stage**
Approximate Vapour Capacity*
7525B34¼“ Inverted
Flare½“ F.NPT
28 mbar @ 6,8 bar Inlet
23-33 mbar Outlet 8,4 kg/h*
Kit Number Automatic Change-over Regulator Inlet Outlet Pigtails
Included-2 Bracket IncludedApproximate
Vapour Capacity Propane
5726B34 7525B34 ¼“ Inverted Flare
½“ F.NPT912FA20
2302-31 8,4 kg/h5727B34 7525B34 912FS20
Ordering Information
MaterialsBody First Stage Die Cast Zinc
Bonnet First Stage Die Cast Zinc
Bonnet First Stage Die Cast Zinc
Body Second Stage Die Cast Zinc
Bonnet Second Stage Die Cast Zinc
Diaphragms Int. Fabric & Synthetic Rubber
Springs Steel & Stainless Steel
Valve Discs Resilient Rubber
* Maximum fl ow based on 0,7 bar Inlet 23 mbar delivery pressure
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use.
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
PU/200
www.rego-europe.de
Page 14
www.rego-europe.de
Page 15
RegO® LV404B Series Special Purpose LP-Gas Compact Twin-Stage Regulators
LV404B Series
ApplicationCompact two-stage regulator is designed to reduce container pressure up to 17.2 bar down to a pressure between 28-87 millibar; the actual adjustable pressure range is specifi ed in the table below. Ideal for use on smaller LPG installations.
MaterialsBody First Stage Die Cast Zinc
Body Second Stage Die Cast Zinc
Bonnets Die Cast Zinc
Diaphragms Int. Fabric & Synthetic Rubber
Springs Steel
Valve Discs Resilient Rubber
Part NumberInlet
ConnectionInches
Outlet Connection
Inches
Delivery Pressure@7 bar Inlet
Adj. Rangembar
Bonnet Vent Position Approximate Vapour Capacity
1st Stage 2nd Stage
LV404B4¼” F-NPT
½” F-NPT28 mbar 28 - 33 mbar Down Outlet 11 kg/h
LV404B46 ¾” F-NPT
LV404B9F.POL
½” F-NPT28 mbar 28 - 33 mbar Down Outlet 11 kg/h
LV404B96 ¾” F-NPT
LV404B4H20¼“ F-NPT
½” F-NPT50 mbar 37 - 87 mbar Down Outlet 11 kg/h
LV404B46H20 ¾” F-NPT
Ordering Information
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV404B series are UL approved.
LV404B4
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV404B Series
RegO® New Compact Twin Stage Regulators for LP-Gas LV404B34 & LV404B39 Series
LV404B34 & LV404B39 Series
ApplicationThe compact twin-stage regulator is designed to reduce container pressure down to 28 mbar. delivery pressure. It is ideal for “on site” container applications such as homes, mobile homes and cottages for average dome-stic service; including small ASME tanks and 100-420 pound DOT cylinders.
Part Number
Inlet Connection
Outlet Connection
Orifi ce Size
FactoryDelivery Pressure
AdjustmentRange 2nd
Stage
Bonnet Vent Position 1st
Stage**
Bonnet Vent Position 2nd
Stage**
Approximate Vapour
Capacity*LV404B34 ¼“ F.NPT
½“ F.NPT6,3 mm
28 mbar @ 6,8
bar Inlet
23 - 33 mbar
Rear Outlet
9,4 kg/hLV404B39 F.POL
LV404B34V9 ¼“ F.NPTLeft 9:00
LV40439V9 F.POL
Ordering Information
FeaturesLarge vent helps prevent vent blockage, the second ¢stage regulator bonnet is tapped for 3/8”F.NPT for vent piping, the high pressure regulator is tapped with 1/8” F.NPT for vent piping.With 1bar inlet pressure, the regulator is ¢designed to not pass more than 137 mbar down-stream with the seat disc removed.Incorporates a integral relief valve on second stage. ¢Unique bonnet vent profi le minimizes vent freeze ¢over when properly installed.Compact design saves space allows for easy ¢installation – especially under container hoods with collarsBuilt in pressure taps 1/8” F.NPT on both high ¢pressure regulator inlet and downstream side of the second stage regulatorPlugs can be removed with a 3/16” hex ¢Allen wrenchSelect brown fi nish. ¢
* Maximum fl ow based on 0,7 bar Inlet 23 mbar delivery pressure | ** Other vent positions available upon request
MaterialsBody First Stage Die Cast Zinc
Bonnet First Stage (LV404B34) Die Cast Zinc
Bonnet First Stage (LV404B39) Brass
Body Second Stage Die Cast Zinc
Bonnet Second Stage Die Cast Zinc
Diaphragms Int. Fabric & Synth. Rubber
Springs Steel & Stainless Steel
Valve Discs Resilient Rubber
LV404B34 LV404B39
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use.
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
PU/194
www.rego-europe.de
Page 16
www.rego-europe.de
Page 17
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV3403B4
Downstream Pressure Tap Inlet Pressure Tap 1/8“ F.NPT
101.47 mm
101.35 mm
Straight Through Design
103.12 mm
RegO® Compact Second Stage Regulators LV3403B4
ApplicationThe LV3403B4 is designed to reduce fi rst stage pressure of 0.35 to 1.5 bar down to burner pressure normally 28 mbar. Designed as a second stage regulator for smaller applications with fl ow requirements up to 9.6 kg/h, they are ideal for homes, mobile homes, and cottages.
FeaturesLarge vent helps prevent vent blockage, it is tapped ¢for 3/8”F.NPT for vent piping.With 1.03 bar inlet pressure, the regulator is de- ¢signed to not pass more than .14 bar downstream with the seat disc removed.Incorporates a integral relief valve ¢Unique bonnet vent profi le minimizes vent freeze ¢over when properly installed.Design provides for good fl ow regulation at both ¢high and low container pressures.Compact design saves space. ¢Built in pressure taps 1/8” F.NPT on both regulator ¢inlet and downstream side of the regulator. Plugs can be removed with a 3/16” hex Allen wrench.Select brown fi nish. ¢
Ordering Information
Part Number Inlet Connection
Outlet Connection Orifi ce Size Factory Delivery
Pressure Adjustment
RangeBonnet Vent
Position Approximate
Vapour Capacity
LV3403B4 ½” F.NPT ½” F.NPT 6,3 mm 28 mbar 23 - 33 mbar Inlet 9,6 kg/h
LV3403B4V3 ½” F.NPT ½” F.NPT 6,3 mm 28 mbar 23 - 33 mbar 3 o‘clock 9,6 kg/h
LV3403B4V0 ½” F.NPT ½” F.NPT 6,3 mm 28 mbar 23 - 33 mbar Outlet 9,6 kg/h
LV3403B4V9 ½” F.NPT ½” F.NPT 6,3 mm 28 mbar 23 - 33 mbar 9 o‘clock 9,6 kg/h
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV3403B series are UL approved.
MaterialsBody & Bonnet Die Cast Zinc
Nozzle Orifi ce Brass
Spring Steel
Valve Seat Disc Resilient Rubber
Diaphragm Integrated Fabric & Synthetic Rubber
NEW
RegO® Low Pressure Second Stage RegulatorsLV4403B
LV4403B Series
ApplicationDesigned to reduce fi rst stage pressure of 0,35 to 1,4 bar down to burner pressure, normally 28 mbar. Ideal for medium commercial installations, multiple cylinder installations and normal domestic loads.
Backmount DesignMounts directly to house line piping. Eliminates need for union joints, elbows, and mounting brackets. Quick and easy to install.
Ordering Information
Part Number Inlet Connection
Outlet Connection
Orifi ce Size
Factory Delivery Pressure
Adjustment Range
Bonnet Vent Position
Approximate Capacity**
LV4403B4 ½“ F. NPT ½“ F. NPT 3,5 mm 28 mbar 23 – 33 mbar Over Inlet 20 kg/h
LV4403B46 ½” F. NPT ¾“ F. NPT 3,5 mm 28 mbar 23 – 33 mbar Over Inlet 20 kg/h
LV4403B46R* ½“ F. NPT ¾“ F. NPT 3,5 mm 28 mbar 23 – 33 mbar Over Inlet 20 kg/h
LV4403B66 ¾“ F. NPT ¾“ F. NPT 3,5mm 28 mbar 23 – 33 mbar Over Inlet 20 kg/h
LV4403B66R* ¾“ F. NPT ¾“ F. NPT 3,5 mm 28 mbar 23 – 33 mbar Over Inlet 20 kg/h
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV4403B Series are UL approved.
* Backmount design.** Maximum fl ow based on 0,7 bar inlet and 23 mbar delivery pressure.
MaterialsBody Die Cast Zinc
Bonnet Die Cast Zinc
Nozzle Orifi ce Brass
Spring Steel
Valve Seat Disc Resilient Rubber
Diaphragm Integrated Fabric & Synthetic Rubber
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV4403B Series
www.rego-europe.de
Page 18
www.rego-europe.de
Page 19
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
RegO® Low Pressure Second Stage RegulatorsLV4403H Series
ApplicationDesigned to reduce fi rst stage pressure of 0.35 to 1.5 bar down to burner pressure, normally 36 mbar.Ideal for medium commercial installations, multiple cylinder installations and normal domestic loads.
FeaturesLarge vent helps prevent blockage and has ¾” ¢F.NPT for vent piping.With 1 bar inlet pressure, regulator is designed to ¢not pass more then 138 mbar with the seat disc removed.Incorporates integral relief valve ¢Replaceable valve orifi ce and valve seat disc. ¢Unique bonnet vent profi le minimizes vent freeze ¢over when properly installed.Large moulded diaphragm is extra sensitive to pres- ¢sure changes.Built in pressure tap has plugged 1/8’’ F.NPT out- ¢let. Plug can be removed with a 3/16” hex allen wrench.Select brown fi nish. ¢Length of the Regulator 18 cm ¢Height of the Regulator 11,8 cm ¢Length between the bracket screws 11,4 cm ¢
Ordering Information
Part Number Inlet Connection
Outlet Connection
Orifi ce Size
Factory Delivery Pressure
@ 0.7 bar inlet
Adjustment Range
Bonnet Vent Position
Approximat Capacity
LV4403H222 ¼“ F.NPT ½” F.NPT 3,5 mm 50mbar 37 – 87 mbar Over inlet 14 kg/h
LV4403H414 ½” F.NPT ½“ F.NPT 3,5 mm 36mbar 31 – 47 mbar Over inlet 14 kg/h
LV4403H420 ½“ F.NPT ½” F.NPT 3,5 mm 50mbar 37 – 87 mbar Over inlet 14 kg/h
LV4403H4614 ½” F.NPT ¾“ F.NPT 3,5 mm 36mbar 31 – 47 mbar Over inlet 14 kg/h
LV4403H4620 ½” F.NPT ¾“ F.NPT 3,5 mm 50mbar 37 – 87 mbar Over inlet 14 kg/h
LV4403H6614 ¾” F.NPT ¾“ F.NPT 3,5 mm 36mbar 31 – 47 mbar Over inlet 14 kg/h
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV4403H Series are UL approved.
MaterialsBody Die Cast Zinc
Bonnet Die Cast Zinc
Nozzle Orifi ce Brass
Spring Steel
Valve Seat Disc Resilient Rubber
Diaphragm Integrated Fabric & Synthetic Rubber
LV4403H Series
RegO® Low Pressure Second Stage RegulatorsLV4403K46 Series
ApplicationDesigned to reduce fi rst stage pressure 0.35 to 1.5 bar down to appliance pressure nominal 29 mbar, the adjustment range is specifi ed in the table below. Ideal for medium commercial installations, multiple cylinder installations and normal domestic loads.
Ordering Information
Part Number Inlet Connection
Outlet Connection
Orifi ce Size
Factory Delivery Pressure
Adjustment Range
Bonnet Vent Position
ApproximateCapacity
LV4403K46 ½“ F. BSP ¾“ F-BSP 3,5 mm 30 mbar 27 – 37 mbar Outlet 17 kg/h
LV4403K46V9 ½” F. BSP ¾“ F-BSP 3,5 mm 30 mbar 27 – 37 mbar 9 o‘clock 17 kg/h
MaterialsBody Die Cast Zinc
Bonnet Die Cast Zinc
Nozzle Orifi ce Brass
Spring Steel
Valve Seat Disc Resilient Rubber
Diaphragm Integrated Fabric & Synthetic Rubber
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use.
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV4403K46 Series
www.rego-europe.de
Page 20
www.rego-europe.de
Page 21
RegO® Low Pressure Second Stage RegulatorsLV5503B Series
ApplicationDesigned to reduce fi rst stage pressure of 0,35 to 1,4 bar down to burner pressure, normally 28 mbar.Ideal for larger commercial and industrial applications.
Ordering Information
Part Number Inlet Connection
Outlet Connection
Orifi ce Size
Factory Delivery Pressure
Adjustment Range
Bonnet Vent Position
Approximate Capacity
LV5503B4 ½“ F. NPT ¾ “ F. NPT 6,3 mm 28 mbar 23 – 33 mbar Over Inlet 35 kg/h
LV5503B6 ¾“ F. NPT ¾“ F. NPT 6,3 mm 28 mbar 23 – 33 mbar Over Inlet 35 kg/h
LV5503B8 ¾“ F. NPT 1“ F. NPT 7 mm 28 mbar 23 – 33 mbar Over Inlet 50 kg/h
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. LV5503 series being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use, and are therefore not marked CE. LV5503B Series are UL approved.
MaterialsBody Die Cast Zinc
Bonnet Die Cast Zinc
Nozzle Orifi ce Brass
Spring Steel
Valve Seat Disc Resilient Rubber
Diaphragm Integrated Fabric & Synthetic Rubber
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV5503B Series
RegO® Low Pressure Second Stage RegulatorsLV5503H Series
ApplicationDesigned to reduce fi rst stage pressure 5-20 PSIG (.035- 1.4 bar) down to a pressure higher than 11” W.C (28 mbar), the actual pressure setting is speci-fi ed in the table below. Ideal for medium commercial installations, multiple cylinder installations and normal domestic loads.
Ordering Information
Part Number Inletconnection
OuttletConnection
Orifi ceSize
Factory DeliveryPressure
@ 0,7 bar Inlet
AdjustmentRange
Bonnet VentPosition
Approximate Capacity
LV5503H414 ½“ F. NPT ¾“ F. NPT 6,3 mm 35 mbar 18 – 40 mbar Over Inlet 35 kg/h
LV5503H614 ¾“ F. NPT ¾“ F. NPT 6,3 mm 40 mbar 18 – 40 mbar Over Inlet 35 kg/h
LV5503H620 ¾“ F. NPT ¾“ F. NPT 6,3 mm 50 mbar 28 – 70 mbar Over Inlet 35 kg/h
LV5503H620V ¾“ F. NPT ¾“ F. NPT 6,3 mm 50 mbar 28 – 70 mbar Over Outlet 35 kg/h
LV5503H640 ¾“ F. NPT ¾“ F. NPT 6,3 mm 100 mbar 70 – 210 mbar Over Inlet 35 kg/h
LV5503H640V ¾“ F. NPT ¾“ F. NPT 6,3 mm 100 mbar 70 – 210 mbar Over Outlet 35 kg/h
LV5503H814 ¾“ F. NPT 1“ F. NPT 7 mm 35 mbar 18 – 40 mbar Over Inlet 50 kg/h
LV5503H820 ¾“ F. NPT 1“ F. NPT 7 mm 50 mbar 28 – 70 mbar Over Inlet 50 kg/h
LV5503H840 ¾“ F. NPT 1“ F. NPT 7 mm 100 mbar 70 – 210 mbar Over Inlet 50 kg/h
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. LV5503H Series are UL approved.
MaterialsBody Die Cast Zinc
Bonnet Die Cast Zinc
Nozzle Orifi ce Brass
Spring Steel
Valve Seat Disc Resilient Rubber
Diaphragm Integrated Fabric & Synthetic Rubber
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV5503H Series
www.rego-europe.de
Page 22
www.rego-europe.de
Page 23
RegO® Large Capacity Second Stage RegulatorsLV6503B Series
LV6503B Series
ApplicationDesigned to reduce fi rst stage pressure of 0,35 to 1,4 bar down to burner pressure, normally 28 mbar.Ideal for larger commercial and industrial applications.
FeaturesTee style inlet and outlet connections - made from ¢ductile ironIncorporate integral large 2“ F.NPT relief vents ¢Built in pressure taps for both inlet and outlet ¢pressureFull capacity relief at 10 psig inlet will keep the ¢down stream preessure at less than 2 PSIG per NFPA 58
Ordering Information
Part Number Inlet Connection
Outlet Connection
Orifi ce Size
Factory Deli-very Pressure
Adjustment Range
Bonnet Vent Position
Approximate Capacity
LV6503B14 1 ½ “ F. NPT 1 ½ “ F. NPT 16 mm 28 mbar 21 – 35 mbar - 170 kg/h
LV6503B16 2“ F. NPT 2“ F. NPT 16 mm 28 mbar 21 – 35 mbar - 205 kg/h
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. LV6503B Series are CE marked. LV6503B Series are UL approved. Different springs for different settings available.
MaterialsInlet Body Ductile Iron
Body Cast Aluminium
Bonnet Cast Aluminium
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV6503B Series
RegO® High Pressure Industrial Regulators 597 Series
597 Series
ApplicationDesigned to reduce LP-Gas container pressure down to between 0.1 bar and 7,0 bar. Ideal for liquid or vapour service, they can be used in a variety of applications including salamander heaters, weed burning torches, fi sh cookers, tar pot heaters, and other industrial type services.
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below
the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. 597 series are UL approved
Ordering Information
* Set pressure established at 7,0 bar inlet and a fl ow of 5,0 kg/h** Capacity determined at actual delivery pressure 20% less than set pressure with inlet pressure 1,4 bar higher than the set pressure
Part Number Adjustment Method
Inlet Connection
Outlet Connection
Recommended Delivery Pressure
range in bar
Capacity Deter-mined at Set
pressure of bar *
Approximate Capacity
Propane ** 597FA Tee Handle ¼“ F.NPT ¼“ F.NPT 0,1 – 1,0 0,7 37 kg/h
597FB Tee Handle ¼“ F.NPT ¼“ F.NPT 0,7 – 2,0 1,4 63 kg/h
597FC Tee Handle ¼“ F.NPT ¼“ F.NPT 1,4 – 3,0 2,0 73 kg/h
597FD Tee Handle ¼“ F.NPT ¼“ F.NPT 2,8 – 7,0 2,8 94 kg/h
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
MaterialsBody Zinc
Bonnet Zinc
Springs Steel
Valve Seat Discs Resilient Rubber
Diaphragm Integrated Fabric & Synthetic Rubber
Adjusting Screw Brass
597 Series
RegO® High Pressure/High Temperature Industrial/Commercial Regulators
X1584V, X1586V, X1588V Series
ApplicationDesigned to reduce LP-Gas container pressures between 0,2 and 8,6 bar. Ideal for crop drying, heat treating, asphalt batch mixing and other large industrial and commercial load applications such as vaporizers that utilize high temperature LP-Gas or high temperature atmosphere under conditions up to 148,8°C. Also ideal as a fi rst stage regulator in large multiple operations.
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below
the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use. 1580V series are UL approved.
Ordering Information
* Set pressure is established with 7 bar inlet pressure and a fl ow of 10,5 kg propane / hour for X1580V series.** Capacities determined at actual delivery pressure 20% less than set pressure with inlet pressure 1,4 bar higher then set pressure.NOTE: Care must be taken to prevent re-liquifi cation of propane at normal temperatures by heat tracing or other effective means. Use a relief valve upstream or down stream of these regulators is recommended in accordance with NFPA 58
Part Number Service
Adjust-ment
Method
Inlet & Outlet
Connection
Recommended Delivery Pressure
range in bar
Width(A)
Height(B, max)
Capacity Deter-mined at Set
pressure in bar *
Capacitykg/h
Propane** X1584VN LP-Gas T-Handle ½“ F.NPT 0,2 – 2,1 1,4 147
X1584VL LP-Gas T-Handle ½“ F.NPT 1,7 – 3,5 75 mm 124 mm 2,1 158
X1586VN LP-Gas T-Handle ¾“ F.NPT 0,2 – 2,1 1,4 230
X1586VL LP-Gas T-Handle ¾“ F.NPT 1,7 – 3,5 89 mm 178 mm 2,1 250
X1588VN LP-Gas T-Handle 1“ F.NPT 0,2 – 2,1 1,4 230
X1588VL LP-Gas T-Handle 1“ F.NPT 1,7 – 3,5 89 mm 178 mm 2,1 250
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
MaterialsBody Zinc
Bonnet Zinc
Springs Steel
Valve Seat Discs Resilient Rubber
Diaphragm Integrated Fabric & Synthetic Rubber
Adjusting Screw Brass
Inlet screen protects seal from foreign
material. It is easily
removed for cleaning.
The RegO® Regulator
especially for vaporiser
installations
X1584V, X1586V, X1588V Serieswww.rego-europe.de
Page 24
www.rego-europe.de
Page 25
High Pressure Industrial / Commercial Regulators1580 Series
ApplicationDesigned to reduce LP-Gas and anhydrous ammonia container pressure to between 0,2 and 8,6 bar. Preci-sion-built with capacities of several hundreds kilogram LP-Gas per hour. The 1580V series is perfect for such big, tough jobs as crop dryers, asphalt batch mixing plants, road building „tar wagons“, heat treating and other large industrial and commercial loads. It’s also ideal as fi rst stage regulator in large multiple opera-tions. The AA1580 series is ideal for use in anhydrous ammonia applications. such as blue print machines and heat treating.
Ordering Information
* Set pressure is established with 7 bar inlet pressure and a fl ow of 10,5 kg propane / hour for 1580V series, 2,5 m³/h for AA1582M Series and 5 m³/h for AA1584V and AA1586V Series** Capacities determined at actual delivery pressure 20% less than set pressure with inlet pressure 1,4 bar higher then set pressure.NOTE: Care must be taken to prevent re-liquifi cation of propane at normal temperatures by heat tracing or other effective means.Use a relief valve upstream or down stream of these regulators is recommended in accordance with NFPA 58
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipmentequal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with thesound engineering practice of a Member State in order to ensure safe use. 1580M series are UL approved.
Part Number
Ser-vice
Adjust-ment
Method
Inlet & Outlet
Connection
RecommendedDelivery Pressure
Range
Width(A)
Height(B,max)
Capacity Determined at Set Pressure*
Capacity**
AA1582MW NH³ T-Handle ¼" F.NPT 0,2 - 1,7 bar 56 mm 105 mm 1,4 bar 60 m³/h NH³
AA1582MK NH³ Hex Head ¼" F.NPT 0,2 - 1,7 bar 56 mm 105 mm 1,4 bar 60 m³/h NH³
AA1582ML NH³ T-Handle ¼" F.NPT 1,4 - 3,5 bar 56 mm 105mm 2,1 bar 68 m³/h NH³
AA1582MH NH³ T-Handle ¼" F.NPT 3,1 - 8,6 bar 56 mm 105 mm 4,1 bar 74 m³/h NH³
1584VN LP-Gas T-Handle ½" F.NPT 0,2 - 2,1 bar 75 mm 124 mm 1,4 bar 147 kg/h Propane
1584VL LP-Gas T-Handle ½" F.NPT 1,7 - 3,5 bar 75mm 124 mm 2,1 bar 158 kg/h Propane
1584VH LP-Gas T-Handle ½" F.NPT 3,1 - 8,6 bar 75 mm 124 mm 4,1 bar 168 kg/h Propane
AA1584VW NH³ T-Handle ½" F.NPT 0,2 - 1,7 bar 75 mm 124 mm 1,4 bar 127 m³/h NH³
AA1584VL NH³ T-Handle ½" F.NPT 1,4 - 3,5 bar 75 mm 124 mm 2,1 bar 136 m³/h NH³
AA1584VH NH³ T-Handle ½" F.NPT 3,1 - 8,6 bar 75 mm 124 mm 4,1 bar 144 m³/h NH³
1586VN LP-Gas T-Handle ¾" F.NPT 0,2 - 2,1 bar 89 mm 178 mm 1,4 bar 230 kg/h Propane
1586VL LP-Gas T-Handle ¾" F.NPT 1,7 - 3,5 bar 89 mm 178 mm 2,1 bar 250 kg/h Propane
1586VH LP-Gas T-Handle ¾" F.NPT 3,1 - 8,6 bar 89 mm 178 mm 4,1 bar 295 kg/h Propane
AA1586VW NH³ T-Handle ¾" F.NPT 0,2 - 1,7 bar 89 mm 178 mm 1,4 bar 198 m³/h NH³
AA1586VL NH³ T-Handle ¾" F.NPT 1,4 - 3,5 bar 89 mm 178 mm 2,1 bar 218 m³/h NH³
AA1586VH NH³ T-Handle ¾" F.NPT 3,1 - 8,6 bar 89 mm 178 mm 4,1 bar 252 m³/h NH³
1588VN LP-Gas T-Handle 1 " F.NPT 0,2 - 2,1 bar 89 mm 178 mm 1,4 bar 230 kg/h Propane
1588VL LP-Gas T-Handle 1 " F.NPT 1,7 - 3,5 bar 89 mm 178 mm 2,1 bar 250 kg/h Propane
1588VH LP-Gas T-Handle 1 " F.NPT 3,1 - 8,6 bar 89 mm 178 mm 4,1 bar 295 kg/h Propane
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
1580 Series
www.rego-europe.de
Page 26
www.rego-europe.de
Page 27
High performance and security
in extreme conditions
This is what USA made RegO® regulators give their users
25 years of expected service life of a ECII/RegO® regulator (excluding single stage) on condition that all of our recommendations are followed
Pressure gauge available as an accessory
RegO® Special Purpose LP-Gas Compact Twin-Stage RegulatorLV404 SeriesDesigned to reduce container pressure up to 17,2 bar down to burner pressure
RegO® High Pres-sure Industrial/Commercial Regulators1580 SeriesDesigned to redu-ce LP-Gas and an-hydrous ammonia container pressure to between 0,2 and 8,6 bar.
RegO® Compact First Stage Regulators LV3403 SeriesFor any domestic LPG installations requiring up to 32/45 kg/h.
Non freezing regulator in all conditions
RegO® Low Pressure Second Stage RegulatorLV4403/LV5503 SeriesDesigned to reduce first stage pressure of 0,35 to 1,5 bar down to burner pressure
10 years warranty on all RegO® products (terms and conditions apply)
RegO® products are PED approved
www.rego-europe.de
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
LV4403F66RA Series
13.0
14.0
15.0
16.0
17.0
18.0
19.0
1.5 2.9 4.7 8.8 14.6 21.2 39.5 55.5Cubic Meters/Hr Natural Gas
mba
r
3.0 bar2.5 bar2.0 bar1.5 bar1 bar
RegO® Low Pressure Service Regulators for Natural GasLV4403F66RA Series
ApplicationDesigned to reduce inlet pressure of from 1-3 bar to a delivery pressure of 17.4 mbar.
Features90 degree right angle inlet to outlet connection for ¢standard meter installationsLarge vent helps prevent blockage and has a ¾” ¢F.NPT for vent piping. Straight-line valve closure reduces wear on seat ¢disc.Unique bonnet vent profi le minimizes vent freeze ¢over when properly installed.Large molded diaphragm is extra sensitive to pres- ¢sure changes.Built in pressure tap has plugged 1/8” outlet. Plug ¢can be removed with a 3/16” Allen wrench.Select Brown Finish ¢
Ordering Information
Set point 1.5 bar inlet @ 17.4 mbar delivery pressure
Part Number Inlet Connection
Outlet Connection
Orifi ce Size
Factory Delivery Pressure mbar
Adjustment Range mbar
Bonnet Vent Position
Vapour Capacitym³/h
Natural Gas LV4403F66RA ¾“ F.NPT ¾” F.NPT 3/16“ 17.4 15 – 22.4 Over inlet 30.5
LV4403F66RAB ¾” F.NPT ¾“ F.NPT 3/16“ 17.4 15 – 22.4 Over inlet 30.5
LV4403F66RA9 ¾“ F.NPT ¾” F.NPT 3/16“ 17.4 15 – 22.4 9:00 30.5
Are in accordance with the requirements of Directive 97/23/EC for pressure equipment. But being pressure equipment equal or below the limits in section 1.1, 1.2 and 1.3 of Article 3 are stated to be designed and manufactured with the sound engineering practice of a Member State in order to ensure safe use.
MaterialsBody Die Cast Zinc
Bonnet Die Cast Zinc
Nozzle Orifi ce Brass
Spring Steel
Valve Seat Disc Integrated Fabric & Synthetic Rubber
LV4403F66RA Series
www.rego-europe.de
Page 28
All made with pride in USA
LPGas Products of excellence from the world‘s
leading manufacturer
B Our products are CE or B marked as conforming to:
¢ PED Pressure Equipment Directive 97/23/EC¢ TPED Transportable Pressure Equipment Directive 1999/36/EC
ISO 9001 Certified REGO GmbH is certified according to ISO 9001 by TÜV Germany.
REGO GmbH - Distribution Center Europe Industriestrasse 9, D-35075 Gladenbach, Germany
Phone +49 (0)6462-9147-0, Fax [email protected] · www.rego-europe.de
05-2
011