rcp47-bk base kitpage 2 of 8 rcp47-bk base kit parts list item components qty 1 short fixed mount...
TRANSCRIPT
Page 1 of 8
RCP47-BK Base Kit
Maximum carrying capacity:
Vehicle On Road Cargo Allowance
Off Road Cargo Allowance Roof Allowance Rack Weight
(2.5kg per bar)
VW Caddy/ Caddy Maxi MY11 - on (2 bar) 95kg / 209lbs 63kg / 138lbs 100kg / 220lbs 5kg / 11lbs
VW Caddy/ Caddy Maxi MY11 - on (3 bar) 92kg / 202lbs 61kg / 134lbs 100kg / 220lbs 7.5kg / 11lbs
Mitsubishi Triton Dble Cab/ 2dr Club Cab 04/15 on 75kg / 165lbs 50kg / 110lbs 80kg / 176lbs 5kg / 11lbs
Off Road: Any driven path taken that is not on sealed (tarred / bitumen) and maintainedRoof Allowance: Total permissible weight attached to the roof of the car. This is inclusive of the weight of the roof rack systemCargo Allowance: Total permissible weight allowed on top, and attached to roof racks whilst the vehicle is in motion Static Allowance: Total permissible weight allowed on top, and attached to roof racks whilst the vehicle is stationary Load must be evenly distributed over the roof racks. Weight of roof rack accessories is to be included in cargo allowance.Torque settings Unless stated otherwise in these instructions, all fasteners should be set to the following torque settings -M6: 4-5Nm (3-4lbs/ft), M8: 8-10Nm (6-7.5lbs/ft) and M10: 16-18Nm (12-13lbs/ft).
Warning: • Check the Rhino-Rack website to ensure you have the latest issue of the instructions• Check Part No. and / or Kit is correct for use with your vehicle• Do not attempt to fi t the rack system to your vehicle unless you fully understand these fi tting instructions. Please direct any questions
regarding fi tting to the dealer from where the roof racks were purchased.• Use only non-stretch fastening ropes or straps. • The handling characteristics of the vehicle changes when you transport a load on the roof. For safety reasons we recommend you
exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account when cornering and braking.
• Although the system is tested and approved to AS1235-2000 / ISO 11154, off -road conditions can be much more rigorous. Extreme care must be taken in off road conditions
Recommendations: It is essential that all bolt connections be checked after driving a short distance when you fi rst install your roof racks. Bolt connections should be checked again at regular intervals (once a week is enough, depending on road conditions, usage, loads and distances travelled). You should also check the roof racks each time they are re-fi tted. Always make sure to fasten your load securely. Please also ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible and must be entirely contained within the extents of the roof racks.
Note for Dealers and Fitters: It is your responsibility to ensure these fi tting instructions are given to the end user or client.
Rhino-Rack, 22 Hanson Pl, Eastern CreekNSW 2766, Australia Document No: R1328(02) 8846 1900 Issue No: 03rhinorack.com.au Issue Date: 13/08/2019
These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
Date Purchased:
Date Fitted:
Fitment By:
Km/Mi at Fitment:
Page 2 of 8
RCP47-BK Base Kit
Parts ListItem Components Qty
1 Short Fixed Mount Rotation Block 42 Short Fixed Mount Base Cover 83 Short Fixed Mount Base 44 Tall Fixed Mount Flat Rubber 45 M6 x 35mm Hex Setscrew 46 M6 Spring Washer 47 M6 16mm Flat Washer 48 M8 Fix Point Adaptor 49 Instructions 1
Tools Required: 1. 10mm socket wrench2. 5mm Allen Key (Caddy only)3. Drill and 3 + 11mm drill bit (Triton only)4. Dremel (Triton only)
Note: Legs and Crossbars are sold separate. Be sure to obtain correct kits for your vehicle.
1.
2.
3.
4.
5.
6.7.
Mitsubishi Triton Instructions (for VW Caddy, turn to pg5)
Item 3.
Item 4.
105mm
80mm
Locking RCL Low Leg
Locking RCH High Leg
Item 2.
Item 1.
8.
1
2
Ditch fi ll.
Ditch fi ll.
Ditch fi ll.
330mm.
1133mm.
803mm.
CL330mm.1133mm.
Prepare the base kit
Rear. Front.
Rear. Front.
4dr double cab (for 2dr club cab see pg 3).
Page 3 of 8
RCP47-BK Base Kit
3mm then 11mm drill bit.
3 4
Ditch fi ll.
References made previous.
Dremel.
5(A) (B) (C)
Item 8.
Mitsubishi Triton Club Cab1 Ditch fi ll.
2
oror
(=)
(=) - Marker pen.
Page 4 of 8
RCP47-BK Base Kit
A
B
!Tighten 3-4 Nm while visually watching the roof panel. Over tightening can damage the roof of the vehicle.
Tab inserts to outside of vehicle.
- Ditch fi ll.
- 3mm bit then 11mm drill bit.
- Dremel.
3
5(A) (B) (C)
Item 8.
oror
Installing the leg kit
Page 5 of 8
RCP47-BK Base Kit
VW Caddy/ Caddy Maxi MY11 on Instructions1A
5mm allen key
Volkswagen Caddy
2 Crossbars: Front mounting point and either middle OR rear mounting point
ORPLUS
3 Crossbars:Front, middle and rear mount points used. Additional RCP47H-BK required.
1B
5mm allen key
Volkswagen Caddy Maxi
2 Crossbars: Front mounting point and either Middle OR rear mounting point
3 Crossbars:Front, middle and rear mount points used. Additional RCP47H-BK required.
ORPLUS
2Tab inserts to outside of vehicle.
Store in safe place.
Store in safe place.
Item 8.
Item 8.
Page 6 of 8
RCP47-BK Base Kit
VW Caddy Leg Setup 3 Bar (2 Bar setup pg 7&8)Vortex 3 bar system:
Heavy Duty 3 bar system:
Item 5.Item 6.Item 7.
RCH KitHardware
Item 5.Item 6.Item 7.
SUB0671RCL KitHardware
Item 5.Item 6.Item 7.
RCH KitHardware
Item 5.Item 6.Item 7.
SUB0671
QMHD05
Item 5.Item 6.Item 7.
QMHD05
Item 5.Item 6.Item 7.
RCH KitHardware
QMHD05
VW Caddy Maxi Leg Setup 3 BarVortex 3 bar system:
Heavy Duty 3 bar system:
Item 5.Item 6.Item 7.
Item 5.Item 6.Item 7.
SUB0671
RCL KitHardware
RCH KitHardware
Front Middle Rear
Front Middle Rear
SUB0671
QMVA20
RCH KitHardware
RCL KitHardware
RCL low leg
Item 5.Item 6.Item 7.
QMVA05
RCH KitHardware
RCH Kit Hardware
QMHD25
RCH KitHardware
Item 5.Item 6.Item 7.
Item 5.Item 6.Item 7.
RCH KitHardware
QMHD10
RCL KitHardware
QMHD05
Front Middle Rear
Front Middle Rear
SUB0671
SUB0671
RCL low leg
RCL low leg
RCL low leg
RCH High leg RCH High leg
RCH High leg RCH High leg
RCH High leg RCH High leg
RCH High leg RCH High leg
Page 7 of 8
RCP47-BK Base Kit
VW Caddy Leg Setup 2 Bar, Vortex Bar (front bar + A or B).
Front Bar
RCH KitHardware
Item 5.Item 6.Item 7.
SUB0671
OR
RCH KitHardware
Item 5.Item 6.Item 7.
RCH KitHardware
Item 5.Item 6.Item 7.
SUB0671
Front Bar
Option A
Option B
Option A Option B
Item 5.Item 6.Item 7.
SUB0671
QMHD05
Item 5.Item 6.Item 7.
QMHD05
RCH KitHardware
RCH KitHardware
Middle
Item 5.Item 6.Item 7.
RCH KitHardware
QMHD05
Rear
SUB0671
VW Caddy Leg Setup 2 Bar, Heavy Duty (front bar + A or B)Front Bar
OR
Front Bar
Option A
Option B
Option A Option B
For Caddy Maxi 2 Bar setup see pg 8.
Page 8 of 8
RCP47-BK Base Kit
VW Caddy Maxi Leg Setup 2 Bar, Vortex Bar (front bar + A or B)Front Bar
OR
Front Bar
Option A
Option B
Option A Option B
Item 5.Item 6.Item 7.
RCH KitHardware
VW Caddy Maxi Leg Setup 2 Bar, Heavy Duty (front bar + A or B)Front Bar
OR
Front Bar
Option A
Option B
Option A
Item 5.Item 6.Item 7.
QMHD05
RCH KitHardware
Item 5.Item 6.Item 7.
RCH KitHardware
QMHD05
RCH KitHardware
Item 5.Item 6.Item 7.
RCH KitHardware
Item 5.Item 6.Item 7.
Option B
Item 5.Item 6.Item 7.
RCH KitHardware
QMHD05