ramram--master safety blocksmaster safety · pdf file3 ram-master die safety blocks safety...
TRANSCRIPT
1
The CSA standard Z142-10 requires that Safety Blocks be used whenever dies are being repaired in a press or when work of
any kind is being performed between the slide and bolster.
Safety Blocks are placed between the die punch and holder and must be rated to support the combined static load of the slide
and associated components.
Depending upon the weight to be supported as many as four Safety Blocks may be required. Slides are usually adjustable and
consequently Safety Blocks can be supplied with an adjustable screw providing up to 12 inches of adjustment.
Safety Blocks are manufactured in
Canada from high-strength 6063-T5
aluminum, and are rated according to their length
and whether fixed or adjustable. The adjustable
screws are made of steel or aluminum. Handles and
electrical interlocks are provided as standard but
blocks can be supplied without these features.
RAMRAM--MASTER SAFETY BLOCKSMASTER SAFETY BLOCKS
RAMRAMRAM---MASTERMASTERMASTER
Steel Screw Capacity
Non adjustable, to 95 Tons.
Adjustable, to 53 Tons.
Aluminum Screw Capacity
Non adjustable, to 47.5 Tons.
Adjustable, to 26.5 Tons.
RAMRAMRAM---MASTERMASTERMASTER MANUFACTURED IN CANADA
290 Thompson Drive, Unit 8, Cambridge ON Canada, T. 519.620.8925 - F. 519.620.3265 - E. [email protected] – W. www.vit-ltd.com
2
SAFETY BLOCKS ACCESSORIES
BLOCK HOLDERS
Holders are designed to store all sizes
of Safety Blocks. Made of heavy gauge
steel and painted, they attach to the
press with two 1/4" screws.
Order using part # SBH664
MINI Die Safety Blocks are intended for use in very small presses and complement the
RAM MASTER series. MINI blocks will fit in small spaces where larger blocks would not
fit. (Blocks are 2.5” in diameter).
Add M to end of part number for Plug and F for Socket.
(MF for both)
For example: MSB610MF
NOTE: All blocks are shipped with necessary hardware to
attach your own interlocks.
HOW TO ORDER
Select the required model from the chart below adding M
or F (or both) if interlocks are required.
MINI DIE SAFETY BLOCKS
Model Minimum Maximum
Availability Number Height Height
MSB406 4 6 Stock item
MSB508 5 8 Stock item
MSB610 6 10 Stock item
MSB712 7 12 Stock item
MSB814 8 14 Stock item
MSB916 9 16 Stock item
MSB1018 10 18 Custom item
MSB1120 11 20 Custom item
Model Number Capacity MSB406 10,000 Lbs.
MSB508 10,000 Lbs.
MSB610 10,000 Lbs.
MSB712 10,000 Lbs.
MSB814 10,000 Lbs.
MSB916 10,000 Lbs.
MSB1018 10,000 Lbs.
MSB1120 10,000 Lbs.
Flanges for Stacking
Adjustable to Non -
Adjustable Blocks
290 Thompson Drive, Unit 8, Cambridge ON Canada, T. 519.620.8925 - F. 519.620.3265 - E. [email protected] – W. www.vit-ltd.com
3
RAM-MASTER DIE SAFETY BLOCKS
Safety blocks can be supplied in fixed or adjustable lengths. All models, fixed and adjustable, use an Octagonal
body section and are available in lengths up to 60”. Load ratings are on the back pages of this flyer.
FEATURES All RAM-MASTER Safety Blocks incorporate the following features.
Two holes at 90° to each other are cross
bored in the top portion of adjusting screws so that
a bar may be inserted to aid in turning the screw
when making adjustments Carrying handles are supplied on
all models
Load ratings are
stamped on the body
Interlock chain attached to collar mounting
screw
Electrical Interlock System. (See
“correct usage” on Page 4)
Warning label advising correct
use of safety block
Adjustable screw
Assembly (Adjustable models only).
Adjustable Screws
The amount of adjustment available depends
upon the height of the block. The longest
screw is 16” which gives approximately 12” of
adjustment.
The shorter the block the less the adjust-
ment.
Octagonal extruded aluminium body cut to the required
length.
Blocks may be ordered without inter-
locks but it is the responsibility of the
user to ensure interlocks are used on
all installations. See last page for ordering information
GENERAL SPECIFICATIONS
290 Thompson Drive, Unit 8, Cambridge ON Canada, T. 519.620.8925 - F. 519.620.3265 - E. [email protected] – W. www.vit-ltd.com
4
RAM-MASTER DIE SAFETY BLOCKS ORDERING INFORMATION
NON ADJUSTABLE OCTAGONAL SAFETY BLOCKS
3½″
4⅝”″
Block Length. Inches Capacity. Lbs. (Tons)
1 - 24 190,000 (95)
24½ - 30 173,000 (86)
30½ - 36 169,500 (84)
36½ - 42 164,000 (82)
42½ - 48 158,000 (79)
48½ - 54 155,500 (77)
54½ - 60 155,000 (77)
ADJUSTABLE OCTAGONAL SAFETY BLOCKS - Ratings Show Steel Screw plus Collar/Aluminum Screw plus Collar
When an adjustable screw is used the static load capabilities are as shown. Blocks with adjustable screws cannot hold as heavy a static load as octagonal
safety blocks by themselves. The ratings shown have a safety factor of two.
NOTE. All safety blocks, both fixed and adjust-
able, come with a hole and pin for the interlock
chain plus one or two handles. Interlocks are
extra and must be requested on your order.
Weight 0.833 lbs.in
Non adjustable blocks are available in fixed lengths up to 60”. The table below shows the maximum static load per block in lbs. and tons.
HOW TO ORDER
Simply state the length you require plus the
number of handles (one or two) and if Inter-
locks are required.
NOTE: A block with zero adjustment has a minimum height of 5”. For every
inch of adjustment the minimum height increase by 1”. For example, a block with
6” of adjustment will have a minimum height of at least 11”. Once this requirement
is met the minimum height can be anything up to 60”.
HOW TO ORDER
We need to know the minimum height re-
quired and the amount of adjustment. [Please
read the note below]
The maximum minimum height is 60” and the
normal maximum amount of adjustment is
12”. However blocks with greater amounts of
adjustment can be made.
State with, or without, handles and if inter-
locks are required.
Correct Usage
Safety Blocks must be used when anyone is working in and
around the die area of a press. An electrical interlock must be attached to the Safety
Block so that the press cannot be operated when the blocks are in place. When not be-
ing used the blocks must be stored in a location where the electrical interlock can be
interfaced with the press controls ensuring the press can only be started when the block
is in the stored position, i.e. not in the press.
TECHNICAL ASSISTANCE
If you need help determining what size of
block you need please contact us via
phone at 519-620-8925 or email at
[email protected] Monday to Friday
8:00AM—5PM.
Inches of Adjust-ment
Maximum Static Load. Lbs. (Tons)
STEEL ALUMINUM
2 106,000 (53) 53,000 (26.5)
4 102,500 (51) 51,750 (25.5)
6 98,500 (49) 49,250 (24.5)
8 94,500 (47) 47,250 (23.5)
10 91,000 (45) 45,500 (22.5)
12 87,500 (43) 43,750 (21.5)
290 Thompson Drive, Unit 8, Cambridge ON Canada, T. 519.620.8925 - F. 519.620.3265 - E. [email protected] – W. www.vit-ltd.com
5
A GUIDE TO SIZING DIE SAFETY BLOCKS
Safety blocks are placed between the die punch and holder… see diagram below. They must be rated to support the combined weight of
the press ram, all components attached to the ram and the upper die.
As many four safety blocks may be required in a large press and they should be situated so that the load is evenly distributed between
them.
To account for differences in the distance between the punch and holder safely blocks are usually supplied to be adjustable although they
don’t have to be adjustable providing some provision is made to ensure there is no gap greater that 1/4” between the upper and lower
parts of the die set.
If you know the weight of the press slide and everything attached to it select safety block that matches that number allowing
for a safety factor of two. If this number is not known the weight to be supported can be calculated using the formula shown
below.
Press Bed Area (sq in) x Shut Height (in)
Cubic Inches/Cubic Feet (Constant) 1728 cu in/cu ft
Example
48” x 96” x 24” 110,592
1728 1728
64 cubic feet displacement x 2,000 lb/ cu ft = 128,000 lbs. static load to be supported.
To determine Block Length with the press at the top of its stroke with the stroke adjustment up
(S.U.A.U. see diagram) measure the space between the upper and lower die set. This gives the maxi-
mum length. To determine the S.U.A.U. subtract the ram adjustment from the S.U.A.U. number and
that will give you the minimum height. The difference between the two is the amount of adjustment.
= Cubic Feet Displaced
= 64 Cubic Feet Displaced
290 Thompson Drive, Unit 8, Cambridge ON Canada, T. 519.620.8925 - F. 519.620.3265 - E. [email protected] – W. www.vit-ltd.com