pseries ops manual 060809

8/4/2019 PSeries Ops Manual 060809

1/44

P SerieSOPerATOrS MANUAL

Covs HK P2000, P2000SK, P30, and P30Lss pstols (all calbs and vaants)


2/44

SAFeTY rULeSPlas ad ths opato's manual bo handlng you am. Th ollowng satyuls a placd n ths manual by HK as an mpotant mnd that am saty s yousponsblty. Fams can b dangous and can potntally caus sous nuy, damag topopty o dath, handld mpoply.

1. Never point a irearm at anyone or in any direction other than a SAFE direction, i.e. downrange.

2. Treat all irearms as i they are always loaded.3. Keep your inger o the trigger and outside o the trigger guard until your sights are aligned

on the target and you are ready to ire.4. Keep your inger o the trigger and outside o the trigger guard while loading or unloading the

irearm.5. Keep your inger o the trigger and outside o the trigger guard while pulling the irearm out

o the holster or while returning it to the holster.6. Be sure o your target and the backstop beyond.7. Never give a irearm to or take a irearm rom anyone unless the action is open and the

magazine and/or chamber are ree o any ammunition or brass.

8. Be sure that the ammunition you are using is actory loaded, is o the correct caliber or theirearm in which it is to be used, and that it is not damaged in any way.

9. Beore iring, remove the magazine rom the irearm, lock the action open, make sure thechamber is clear o any ammunition or brass, and check the barrel o the unloadd irearm orany possible obstructions.

10. Beore iring any irearm that is unamiliar to you, make sure that you understand exactly howit unctions. A lack o amiliarity with the irearm can result in serious accidents. Attend acertiied training course on any irearm which you intend to use or with which you are notsuiciently amiliar.

11. Always wear hearing and eye protection when using your irearm.12. Keep all body parts, especially the hands and ingers, away rom the muzzle to avoid injury or

burns.13. Be sure that no part o either hand touches or intereres with the slide. The slide is movedbackward by the recoil orce o the pistol during iring and may cause serious injury.

14. Firearms should be locked and stored separately rom ammunition and beyond the reach ochildren and/or any untrained individuals.

15. Avoid the use o any alcoholic beverages or drugs beore or during your use o a irearm.16. Discharging irearms in poorly ventilated areas, cleaning irearms, or handling ammunition may

result in exposure to lead; a substance known to be associated with birth deects, reproductiveharm and other serious injury. Have adequate ventilation at all times. Wash hands thoroughlyater exposure.

STOP! Know how to cla ths pstol bo attmptng to opat.

Clang th Pstol - The HK Pistol is not considered clear or sae unless:1. The saety/control lever (i present) is on SAFE and;2. The magazine is removed rom the pistol;3. The slide is locked to the rear and;4. The chamber is ree o brass or ammunition.

To Cla th HK Pstol:1. Mak su ngs a outsd o th tgg guad and th pstol s pontd n a sa

dcton at all tms!2. rmov magan. Depress the magazine release lever and remove the magazine rom the

pistol.

3. Opn and lock sld. While pointing the pistol in a sae direction, lock the slide open bypulling the slide rearward as you press the slide release upward. Watch or a cartridge orempty case to be ejected rom the pistol.

4. inspct chamb. Inspect chamber or the presence o a cartridge or empty case by: Visually viewing chamber through open ejection port. Physically inserting finger into chamber through ejection port to check for the presence of a

cartridge or empty case. Remove any cartridges or empty cases from the chamber or from within the pistol.

Th HK Pstol s now consdd Cla.


3/44

WArNiNG: A am has th capablty o takng you l o th l o somonls! B xtmly caul wth you am. An accdnt can occu at anytm and salmost always th sult o not ollowng basc saty uls.

P SsOpatos Manual

Covs all P2000, P2000SK, P30, and P30L ss pstols (allcalbs and vaants)

HeCKLer & KOCH5675 Transport Boulevard

Columbus, Georgia 31907 USATel: (706) 568-1906 Fax: (706) 568-9151

USA Website: www.hk-usa.com Global Website: www.heckler-koch.com

Heckler & Koch USA (Heckler & Koch Inc. and Heckler & Koch Deense Inc.) revised 6/2009, All rights reservedSpecications and models subject to change without notice.


4/44

4

TABLe OF CONTeNTS

Saety Precautions & Clearing ......................................................... Inside Cover

Section 1 Introduction ......................................................................................5

Section 2 Nomenclature .................................................................................10

Specifcations ..................................................................................12

Section 3 Function & Operation ....................................................................14

Clearing...........................................................................................14

Operating Controls & Components ..............................................15

Sights & Sight Adjustment .............................................................16

Section 4 Ammunition ....................................................................................17

Section 5 Instructions or Use ........................................................................18

Filling & Emptying the Magazine ..................................................18Loading ..........................................................................................18

Firing ...............................................................................................19

Unloading ......................................................................................19

Selection & Use o a Holster ..........................................................20

Storage & Transport ......................................................................20

Interchangeable Grip Panels ..........................................................21

Section 6 Disassembly & Assembly ...............................................................24

Magazine Disassembly ...................................................................28Magazine Assembly .......................................................................30

Section 7 Cleaning & Maintenance ...............................................................31

Inspection ......................................................................................31

Lubrication .....................................................................................32

Troubleshooting Problems & Repair .............................................33

HK Lock-Out Device ..............................................................................34

Accessories .............................................................................................35

Section 8 P2000 Parts List .....................................................................................36

Exploded View .......................................................................................37

Parts List - P2000SK ..............................................................................38

Exploded View .......................................................................................39

Parts List - P30 .......................................................................................40

Exploded View .......................................................................................41

Firearms Service Record ......................................................................42


5/44

5

SeCTiON 1 iNTrODUCTiON

The HK "P Series" includes the P2000, P2000SK (Subcompact), P30, and P30L; all majorhandgun models recently developed by Heckler & Koch.

The P2000 and P2000SK (Subcompact) incorporate eatures o the successul HK USPCompact pistol with the latest innovations o HK engineers. A renement o a designcreated or several European police agencies, the P2000 and P2000SK are available witha traditional single-action/double-action trigger mode and the LEM (Law EnorcementModication) trigger system rst introduced by HK in 2001 on the USP Compact LEMmodel.

The HK Law Enorcement Modication (LEM) trigger system, also known as the CombatDeense Action system in Europe, combines the advantages o a cocked strikercomponent (constant level o trigger pull rom rst to last round red) with a double-actionhammer system. Using such an enhanced trigger system consolidates ease o use and

saety into a convenient, innovative trigger operationone that reduces the chance ounintended ring. And in case o an ammunition-related ailure to re, all that is neededis an additional second or third squeeze o the trigger without the need o rst pulling theslide back to re-cock the pistol. The enhanced LEM trigger system combines the reliabilityo a double action revolver trigger with the crisp trigger o a single action pistol.

On P2000 and P2000SK variants using the conventional double-action/single-action(DA/SA) mode o operation an ambidextrous decocking button is mounted on the let,rear portion o the rame. It allows the user to saely lower the hammer rom SA positionto DA position. This DA/SA variant o the P2000 and P2000SK is readily identiable by the

presence o the serrated decocking button and spurred hammer.

A set o simple-to-install modular grip inserts allow all P2000/P2000SK models to becustom-tted to any shooters hand. An ambidextrous magazine release and dual sliderelease levers make handling P2000/P2000SK pistols natural and easy or right and let-handed shooters alike.

The addition o industry standard mounting rails to the P2000 and P2000SK allows thewidest variety o lights, aimers, and accessories to be added by sliding them onto theopen rail system. The HK P2000 US model uses widely available, reliable USP Compact

magazines. The same magazines t the P2000SK or added repower, but extend pass thegrip.

Like the P2000 and P2000SK, the P30 and P30L (Long Slide) are modern police andsecurity pistols that combines unction and saety. Ergonomic eatures includes a specialrame with interchangeable backstraps inserts and lateral grip panels (lateral plates),allowing the pistol to be individually adapted to any user.

Multiple trigger ring modes include the Law Enorcement Modication (LEM) enhanceddouble action covered previously and a conventional double-action/single-action(DA/SA) with a serrated decocking button located on the rear o the rame. A conventionalsaety lever can also be placed on the rame o the P30/P30L. Other ambidextrous controlsinclude dual slide and magazine release levers.

A Picatinny rail molded into the ront o the rame makes mounting lights, laser aimers, orother accessories easy and convenient and a double action hammer with a ring pin blocksaety that eliminates the need or a manual saety. Extensively tested, the P30and P30Lhave already been adopted by several European police agencies. Excellent weight andbalance make all P30 models naturally pointable, easy to control, and accurate to shoot.


6/44

6

A set o easy-to-install modular back straps allow the P30 and P30L pistols to be custom-tted to any shooters hand. The P30 also incorporates interchangeable side panels oroptimal t. Ambidextrous slide release levers and magazine release levers make handlingthe P Series pistol natural and easy or right and let-handed shooters. The P30 and P30Lare also available with the LEM or DA/SA trigger systems

Due to their modular design, all HK P Series pistol can be tted to the individual needs othe shooter. Highly reliable, sae, durable, and accurate pistols with signicant ergonomiceatures, the P30 pistol is currently available in 9 mm. The P2000 and P2000SK pistols arecurrently available in .40 S&W, 9 mm, and .357 SIG.

Sgncant atus nclud: Modular grip with exchangeable back straps to easily adjust the grip size to the

shooter's hand The P30 incorporates interchangeable grip panels in addition to the interchangeable

backstraps

Ideal size and weight to comply with the requirements of the full range of police andsecurity missions, including concealed carry Set of industry standard (P2000 and P2000SK) mounting grooves molded into the

polymer rame or installing accessory lights and laser aimers Picatinny Rail (available on the P30 and P30L) Advanced design with contoured external surfaces to avoid snagging on holster and

clothing Polymer recoil absorber stop bushing used on P2000, P30, and P30L aids in recoil

reduction, double recoil/buer spring assembly used on P2000SK used Ambidextrous slide release (located on both sides of the frame) Ambidextrous magazine release

Low-profile slide and slimline, compact dimensions Very short trigger reset distance to enhance the speed of multiple or follow-up shots No snag hammer with a rubber insert or improved dropped saety Polygonal cold-hammer orged barrel or less barrel wear, better gas seal behind the

bullet, and easier bore cleaning

All P Series pistols use a modied Browning-type action, much like the HK USP and USPCompact. And like the USP and USP Compact, the P Series pistols also uses a similarmechanical recoil reduction system. This system includes a specially designed fat recoilspring, contained in the captive recoil spring assembly by an absorber bushing made

o a high-strength polymer. The double recoil/buer spring assembly used on P2000SKperorms the same unction.

The polymer rame o the P Series pistol was designed using technical experience gainedby HK engineers in the development o the world's rst composite material pistols, theHK VP70Z and P9S, and more recently, in the USP and USP Compact. These same high-strength/corrosion-ree materials are used in the Mark 23/MK 23 handgun made by HKor the U.S. Special Operations Command. Major metal components like the one-piece,machined steel slide are also corrosion resistant and treated with a special HE (HostileEnvironment) protective nish. The HE nish is an extremely hard, nitro-gas carburized black

oxide coating which resists much o the worst types o corrosion and wear, including limitedexposure to salt water.

Law enocmnt ModcatonThis unique pre-cocked hammer system combines the advantages o a cocked strikercomponent (constant level o trigger pull and short trigger travel rom rst to last roundred) with the double-action hammer system. This ensures an extremely sae pistol withregard to unintended ring and, in case o ailure to ignite, the possibility o a second orthird trigger pull without the need o rst pulling the slide back to re-cock the system.


7/44

7

This is a major advantage over the striker-red trigger systems employed by competingmanuacturers which need to be manually re-cocked (slide pulled back) beore the triggercan be pulled.

Law enocmnt Modcaton (LeM) Vaant 2 (V2)Fng Doubl-acton only mod - (Hammer uncocked)

1. Am - Aim at the target.2. F - Fire the pistol by pressing the trigger straight to the rear with gradually increasingpressure.

NOTe: Th P2000, P2000SK, P30, and P30L modls wth LeM tgg systms n a Doubl-Acton Only mod and ts hamm wll automatcally tun to thuncockd poston ach tm th sld tuns to ts owad poston and th tggs lasd.

P Series pistols tted with the Law Enorcement Modication (LEM) trigger operate much

like standard Double-Action Only (DAO) variants o the USP and USP Compact pistols.However, the way in which the LEM hammer is cocked is unique. The hammer in the LEMis a two-piece hammer comprised o a cocking piece (not visible with the pistol assembled)and an external (visible) bobbed hammer.

In the LEM system, the quality o the trigger pull is improved, while at the same time astronger hammer spring can be employed to improve reliability by increasing the ring pinindent on the primer. The stronger hammer spring also helps to reduce the slide velocitywhen ring hot ammunition.

P2000, P2000SK, P30 and P30 L pistols with an LEM trigger system use the rearward move-

ment o the slide during loading or ring to ully compress the hammer spring instead orelying on the rearward pull o the trigger as in conventional DA or DAO systems.

The cocking piece and hammer are rotated rearward on the hammer axle when the slidemoves ully rearward. When ully to the rear, the cocking piece is held in the cocked posi-tion by the sear and the hammer spring has been ully compressed by the hammer strut.As the slide travels orward, the hammer is rotated back and held in the orward positionby the hammer rebound spring.

When the trigger is pulled rearward against the combined orce (@ 7.5 8.5 pounds new)

o the trigger, hammer rebound, ring pin block and sear springs, the internal passivesaeties are disengaged and the sear releases the cocking piece. The cocking piece is thenree to rotate the hammer orward on its axle, under pressure o the compressed hammerspring, imparted through the hammer strut to strike the ring pin and re the chamberedround.

Doubl Acton/Sngl Acton Vaant 3 (V3)Fng th Sngl-Acton (SA) Mod Pstol (Hammer cocked, DA/SA variant)1. Am Aim at the target.2. F Fire the pistol by pressing the trigger straight to the rear with gradually increasing

pressure.

Doubl-Acton (DA) Mod (Hammer uncocked, DA/SA variant)1. engag Dcockng Lv Apply orward pressure to the serrated surace o the de-

cocking lever. This allows the hammer to saely assume the uncocked position.2. Am Aim at the target.3. F Fire the pistol by pressing the trigger straight to the rear with gradually increasing

pressure.4. Dcock Engage decocking lever to return to the double-action mode. The P Series


8/44

8

DA/SA variant will revert to the single-action mode on each shot unless the operatorphysically decocks the hammer by way o the decocking lever.

Unloadng th Pstol - To unload the pistol, ollow the Clearing procedure.

Clang th Pstol - HK P Series pistols are not considered clear or sae unless:

1. The magazine is removed rom the pistol.2. The slide is locked to the rear.3. The chamber is ree o brass or ammunition.

To Clear the HK P Series pistol:1. Make sure ingers are outside o the trigger guard and the pistol is pointed in a sae

direction at all times!2. Remove magazine - Depress the magazine release lever and remove the magazine from

the pistol.3. Open and lock slide - While pointing the pistol in a sae direction, lock the slide open by

pulling the slide rearward as you press the slide release upward. Watch or a cartridge orempty case to be ejected rom the pistol.4. Inspect chamber - Inspect chamber or the presence o a cartridge or empty case by:

Visually viewing chamber through open ejection port. Physically inserting finger into chamber through ejection port to check for the

presence o a cartridge or empty case. Remove any cartridges or empty cases from the chamber or from within the

pistol.

The HK Pistol is now considered Clear.

On the double-action/single-action variant, pulling the trigger will cock the hammer andimmediately release it ring the rst chambered cartridge. All subsequent cartridges willbe red in the single-action mode because the slide automatically recocks the hammerater each shot is red.

Doubl-acton/Sngl-acton Mods (P Ss pstol) - The P Series DA/SA variant(designated a Variant 3) is congured with a combination double-action/single-actionmode o operation. The P Series DA/SA variant is not equipped with the LEM triggermechanism.

In the single-action mode, rearward movement o slide cocks the hammer. Initially, thisoccurs by either depressing the slide release when the slide is locked back to the rear orby grasping and then releasing the slide. Serrations cut on both let and right sides othe rear o the slide aid the operator by providing a rmer gripping surace. Ater the rstround o the magazine is chambered then discharged, all subsequent cartridges will bered in the single-action mode again due to the rearward movement o the slide passingover and cocking the hammer. In the double-action mode, pulling the trigger will cock thehammer and immediately release it ring the rst chambered cartridge. All subsequentcartridges will be red in the single-action mode because the slide automatically recocks thehammer ater each shot red.

Dcockng Lv (P Ss DA/SA Vaant 3) - P Series DA/SA variants are equippedwith a decocking lever that allows the operator to saely lower the hammer without havingto engage the trigger. The pistol will now unction and re in the double-action mode,however; all subsequent shots will be single action. The decocking lever is located on therear o the rame to the let o the hammer and is activated by simply applying orwardpressure on the serrated surace (see Figure 1).


9/44

9

Figure 1 Figure 2

On variants using a conventional double-action/single-action (DA/SA) mode o opera-tion, a decocking lever is mounted on the let, rear portion o the rame. It allows the userto lower the hammer rom SA position to DA position. This variant o the P Series U.S. isreadily identiable by the presence o the serrated lever (see Figure 2).

P Series pistols have an ambidextrous magazine release lever which is shielded rom inad-

vertent actuation by the fared trigger guard. The magazine release lever can be pressedwith the thumb or index nger o the ring hand; in most cases without adjusting the ringgrip.

Another unique eature making the P Series pistol truly ambidextrous is the presence o aslide release on both sides o the rame. These slide release levers are positioned to alloweasy actuation without adjustment o the grip o the shooting hand and are easily removedduring operator disassembly.

Low-prole 3-dot sights are standard on the P Series pistol. The rear sight is drit adjustableor windage. Elevation changes can be made by replacing the ront sight blade with anaccessory sight o a dierent height.

The P Series pistol uses metal magazines to minimize the grip size. These magazines havea series o viewing holes on the back side or counting the cartridges remaining inside. Anextended magazine foorplate with a durable nger extension is provided on each pistol'smagazine. Floorplates on all magazines can be removed or cleaning and maintenance. Thepolymer foorplate oers a level o protection to the magazine i dropped.

WArNiNG: P Ss pstols, xcpt spcal modls wth a magan dsconnctatu nstalld, wll th magan s movd, a catdg s n th chamb,

and th tgg s pssd.To reduce barrel wear, the P Series pistols have polygonal, cold-hammer orged barrels.This eature not only ensures longer barrel lie and easier bore cleaning, but produces abetter gas seal behind the bullet or increased muzzle velocity.

A set o industry standard mounting grooves or installing accessories is molded in thepolymer rame. These grooves allow many accessories and targeting devices to be mount-ed on the P Series pistols without modication to the pistol.

NOTe: impoply dsgnd o nstalld accssos may sult n damag to thmountng goovs and/o th pstol. Such damag s not covd und th lmtdltm waanty. B ctan to us only HK authod accssos and ollow nstal-laton and pcautons caully.

The P Series pistol is an extremely sae rearm with both passive and active saeties. Theuser activated HK Lock-Out Device is also installed on the P Series pistol (see pages 36and 37 or more inormation on this eature). Sae, simple to eld strip and maintain, the PSeries pistol is a reliable and trouble-ree pistol.


10/44

10

Figure 3A P2000 (let side view)

SeCTiON 2 NOMeNCALTUre

Figure 3B P2000 SK (right side view)


11/44

11

Figure 4B P30L (let side view)Inset o P30 with saety lever and decocker

Figure 4A P30 (right side view)


12/44

12

P2000 SPeCiFiCATiONS________________________________________________________________________________

Caliber .40 S&W, .357 SIG 9mm x 19Operating Principle Short recoil, modiied Short recoil, modiiedAction Type Browning type, linkless Browning type, linkless

________________________________________________________________________________Sights Three dot, ixed patridge Three dot, ixed patridge

style, drit adjustable style, drit adjustableTotal Length 173mm (6.81 in.) 173mm (6.81 in.)Barrel Length 93mm (3.66 in.) 93mm (3.66 in.)Barrel Proile Six-sided polygonal Six-sided polygonalSight Radius 142mm (5.59 in.) 142mm (5.59 in.)Twist Length 250mm (9.84 in.) 250mm (9.84 in.)

________________________________________________________________________________Overall Height (with magazine inserted) 138mm (5.43 in.) 138mm (5.43 in.)Overall Width 34mm (1.34 in.) 34mm (1.34 in.)Weight (with empty magazine) 765 grams (27 oz.) 709 grams (25 oz.)Weight o empty magazine 85 grams (3 oz.) 85 grams (3 oz.)

________________________________________________________________________________

Trigger Pull 32.5 Newtons (7.31 pounds) 32.5 Newtons (7.31 pounds)Trigger Travel (partially cocked) approx. 13.5mm (.53 in.) approx. 13.5mm (.53 in.)For strings o rapid ire, it is not necessary to release thetrigger to the starting position. It will be suicient to releasethe trigger approximate 7 mm to ire the next shot.

Magazine Capacity 10 cartridges / 12 cartridges 10 cartridges / 13 cartridgesSaety Features Double-action mode with hammer intercept notch Firing pin block Disconnector

________________________________________________________________________________ Variant 2 (V2) Law Enorcement Modiication (LEM) enhanced DAOVariant 3 (V3) Double Action/Single Action (DA/SA) with Decocker

P2000 SK SPeCiFiCATiONS________________________________________________________________________________

Caliber .40 S&W, .357 SIG, 9mm x 19Operating Principle Short recoil, modiied Short recoil, modiiedAction Type Browning type, linkless Browning type, linkless__________________________________________________________________________________________________Sights Three dot, ixed patridge Three dot, ixed patridge

style, drit adjustable style, drit adjustableTotal Length 163mm (6.42 in.) 163mm (6.42 in.)Barrel Length 83mm (3.27 in.) 83mm (3.27 in.)Barrel Proile Six-sided polygonal Six-sided polygonalSight Radius 132mm (5.20 in.) 132mm (5.20 in.)

Twist Length 250mm (9.84 in.) 250mm (9.84 in.)__________________________________________________________________________________________________Overall Height (with magazine inserted) 117mm (4.61 in.) 117mm (4.61 in.)Overall Width 36mm (1.28 in.) 36mm (1.28 in.)Weight (with empty magazine) 730 grams (25.8 oz.) 675 grams (23.8 oz.)Weight o empty magazine 75 grams (2.65 oz.) 75 grams (2.65 oz.)__________________________________________________________________________________________________Trigger Pull 32.5 Newtons (7.31 pounds) 32.5 Newtons (7.31 pounds)Trigger Travel (partially cocked) approx. 13.5mm (.53 in.) approx. 13.5mm (.53 in.)

For strings o rapid ire, it is not necessary to release thetrigger to the starting position. It will be suicient to releasethe trigger approximate 7 mm to ire the next shot.

Magazine Capacity 9 cartridges 10 cartridgesSaety Features Double-action mode with hammer intercept notch Firing pin block Disconnector__________________________________________________________________________________________________

Variant 2 (V2) Law Enorcement Modiication (LEM) enhanced DAOVariant 3 (V3) Double Action/Single Action (DA/SA) with Decocker

__________________________________________________________________________________________________

Speciications and models subject to change without notice.


13/44

13

P30 SPeCiFiCATiONS

___________________________________________________________________________________________________Caliber 9mm x 19 .40 S&WOperating Principle Short recoil, modiiedAction Type Browning type, linkless___________________________________________________________________________________________________Sights Open rectangular notch rear sight with

contrast points (no radioactive)Total Length 177.5mm (6.99in.)Barrel Length 98mm (3.86in.)Barrel Proile Six-sided polygonalSight Radius 148.5mm (5.85in.)Twist Length 250mm (9.84 in.)___________________________________________________________________________________________________Overall Height (with magazine inserted) 138mm (5.43 in.)Overall Width 34.8mm (1.37 in.)Weight (with empty magazine) 739 grams (26.08 oz.)Weight o empty magazine 93 grams (3.28 oz.)___________________________________________________________________________________________________Trigger Pull 51 Newtons ( 11.46 pounds)

Trigger Travel (partially cocked) approx. 7mm ( .28in.)For strings o rapid ire, it is not necessary to release thetrigger to the starting position. It will be suicient to releasethe trigger approximate 7 mm to ire the next shot.

Magazine Capacity 15 cartridges (9mm) 13 cartridges (.40 S&W)Saety Features Double-action mode with hammer intercept notch Firing pin block Disconnector___________________________________________________________________________________________________


P30L SPeCiFiCATiONS___________________________________________________________________________________________________Caliber 9mm x 19Operating Principle Short recoil, modiiedAction Type Browning type, linkless___________________________________________________________________________________________________Sights Open rectangular notch rear sight with

contrast points (no radioactive)Total Length 192 mm (7.56 in.)Barrel Length 113 mm (4.45 in.)Barrel Proile Six-sided polygonalSight Radius 163 mm (6.42 in.)

Twist Length 250 mm (9.84 in.)___________________________________________________________________________________________________Overall Height (with magazine inserted) 138 mm (5.43 in.)Overall Width 34.8 mm (1.37 in.)Weight (with empty magazine) 780 grams (27.52 oz.)Weight o empty magazine 93 grams (3.28 oz.)___________________________________________________________________________________________________Trigger Pull 51 Newtons ( 11.46 pounds)Trigger Travel (partially cocked) approx. 7mm ( .28in.)

For strings o rapid ire, it is not necessary to release thetrigger to the starting position. It will be suicient to releasethe trigger approximate 7 mm to ire the next shot.

Magazine Capacity 15 cartridgesSaety Features Double-action mode with hammer intercept notch Firing pin block Disconnector___________________________________________________________________________________________________



14/44

14

SeCTiON 3 FUNCTiON AND OPerATiON

CLeAriNG

WArNiNG: Always cla th pstol bo handlng t.

Clearing the Pistol - The P Series pistol is not considered clear or sae unless:1. The saety/control lever (i present) is on SAFE and;2. The magazine is removed rom the pistol;3. The slide is locked to the rear and;4. The chamber is ree o brass or ammunition.

To Cla th HK P Ss pstol:1. Mak su ngs a outsd o th tgg guad and th pstol s pontd n

a sa dcton at all tms!2. rmov magan. Depress the magazine release lever and remove the magazine

rom the pistol.3. Opn and lock sld. While pointing the pistol in a sae direction lock the slide

open by pulling the slide rearward as you press the slide release upward. Watch ora cartridge or empty case to be ejected rom the pistol.

4. Inspct chamb. Inspect chamber or the presence o a cartridge or empty case by: Visually viewing chamber through open ejection port. Physically inserting finger into chamber through ejection port to check for the

presence o a cartridge or empty case. Remove any cartridges or empty cases from the chamber or from within the

pistol.

Th P Ss pstol s now consdd Cla.

Gnal - (Refer to Figures 3 & 4 for the location of the features described below.)Heckler & Koch P Series pistols are recoil operated and uses a modiied Browning-stylesystem, without a link, to lock and unlock the barrel.

Upon iring, the pressure developed by the propellant gases orces the slide and barrelassembly to the rear. Ater moving approximately 3mm, the locking block will stop therearward movement o the barrel. The barrel is pulled downward due to the engagemento the angled locking suraces o the locking block with those located on the end o therecoil spring guide rod. The locking block disengages rom the slide and the slide contin-ues rearward independently rom the barrel. The extractor, located on the right side o theslide, extracts the spent case. The ejector, positioned in the let side o the rame rearwardo the magazine, will then eject the ired cartridge case. The rearward moving slide thencocks the hammer and compresses the recoil spring.

Once ully to the rear, the compressed recoil spring pushes the slide orward, stripping thenext cartridge rom the magazine into the chamber. I the magazine is empty, the maga-zine ollower lits the slide release into position where it can stop the orward progress othe slide and holds the slide open. I a cartridge is present in the magazine, the slide will

push the cartridge rom the magazine and into the chamber.

WArNiNG: Do not ly on th sld poston to dtmn th magan s mpty.Always chck vsually and physcally to nsu th pstol s not loadd.

During the last 3mm o orward movement, the slide orces the angled suraces o thebarrel locking block against opposing angled suraces on the recoil spring guide rod. Thisaction pivots the locking block on the barrel up into engagement with the ejection port onthe slide. The breech is now locked closed and the next shot can be ired.


15/44

15

OPerATiNG CONTrOLS & COMPONeNTS

WArNiNG: Th P Ss LeM ncopoats a doubl-acton only mod o opaton.Anytm th tgg s pulld wth a catdg n th chamb, th pstol wll omth hamm-down poston.

In the double-action only mode, the hammer always returns to the uncocked (orward)position ater each shot. All shots are ired in the double-action only mode.

Dcockng Button - Double action/single action variants o the P series use a serrated de-cocking located on the rear, let side o the rame to uncocked a cocked pistol. Depressingthe decocking button (usually using the thumb) saely drops the cocked hammer render-ings the pistol sae and uncocked.

Saty Lv ( applcabl) - In addition to a decocking button on the rear o the rame,some P series pistols may also have a saety lever installed on either (or both) sides o the

rame. Pushing the saety lever up into the S position places the pistol on SAFE whilemoving the lever downward into the horizontal F position enables the pistol to re.

When the ront o the saety lever is ully raised above horizontal so that the S on thelever itsel aligns with the reerence line on the rame, the saety lever is engaged and therelease o the hammer is blocked in the single-action mode o re. In the double-actionmode, the hammer will partially cock but will not release to re the pistol. To re the pistol,the front of the control lever is moved down into the horizontal position, i.e. the FIREposition. In this position, the F on the lever aligns with the reerence line located on therame. With the saety lever set on F, the pistol will re i the trigger is pulled and acartridge is in the chamber.

Magan - The P Series model uses the same magazines as the popular USP Compact.P Series magazines are constructed o metal with polymer foorplates, ollowers andlocking plate pieces. Cartridges are positioned within the magazine in a staggered ar-rangement but are ed into the pistol rom a single row under the eed lips. The cartridgesare visible through the numbered viewing holes located in the back o the magazine. Formaintenance and cleaning, all P Series magazines can be disassembled.

No Magan Dsconnct Fatu - For maximum unctionality, most P Series modelsare not equipped with a magazine disconnect eature and can be red with the magazine

removed rom the pistol. The ability to re a semiautomatic pistol while in the processo loading or unloading is considered critical in a military, law enorcement or personaldeense encounter. A magazine disconnect is only available as an optional eature on newP Series pistols (not the P2000SK) or can be retrotted to existing guns. Please contact HKCustomer Service or more inormation (tel. 706-568-1906).

NOTe: To vy th psnc o absnc o th magan dsconnct atu,CLeAr THe P Ss (nsd cov & pag 14), nsung th chamb s mpty, thpstol s unloadd, and pontd n a sa dcton. Wth th magan movd,squ th tgg. i compssng th tgg actvats th hamm and th pstol

dy s, no magan dsconnct s nstalld. i compssng th tgg als toactvat th hamm, a magan dsconnct s psnt.

WArNiNG: P Ss pstols, xcpt spcal modls wth a magan dsconnctatu nstalld, wll th magan s movd, a catdg s n th chamb,and th tgg s pssd.


16/44

16

Ambdxtous Sld rlas - A slide release lever is located on both the let and rightside o the rame directly above the trigger. These levers are used to lock the slide open,to release the slide, and to disassemble the pistol.

As a slide stop, it is lited upward by the magazine ollower or the operator's inger as theslide travels rearward during recoil or manual manipulation. The slide release engages in

the recess located on the let side o the slide at its midpoint. The slide release is springactuated and is held down out o engagement with the slide until required. The sliderelease will automatically hold the slide open when the last shot is ired. As a disassemblylever, the let side slide release is removed rom the let side o the rame when the slide isheld partially rearward. During disassembly, the slide release on the right side o the pistolremains attached to the rame until it is rotated upward approximately 45 and lited othe rame.

Magan rlas Lv - This ambidextrous, spring actuated lever holds the magazinein place within the grip by engaging in the notch ound on the ront o the magazine

housing. Depressing this lever downward with the iring index inger or thumb will allowthe magazine, regardless o the number o cartridges inside, to drop ree o the rame. Themagazine release lever is shielded rom accidental actuation by the design o the polymerrame and lared trigger guard surrounding it.

Fam - All sides o the polymer rame are textured to ensure a irm grip, even with wethands or under conditions o rapid ire. The trigger guard is tapered with the ront suracegrooved to provide a irm grip when using two hands or gloves to ire the pistol. The rameis a one-piece molded component with metal inserts (locking insert and guiding part) castinto the rame during production. The slide rides on these metal inserts during operation.The ront o the rame exterior contains mounting grooves or the attachment o acces-

sories. The bottom rear o the rame has inger recesses located to the let and right o themagazine well or manual extraction o the magazine, i necessary. The serial number othe pistol is engraved in the metal insert incorporated into the ront o the rame, in ronto the trigger guard, on the let side o the slide, and on the barrel locking block.

SiGHTS AND SiGHT ADjUSTMeNTThe P Series uses the proven 3-dot sighting arrangement. By aligning all three dots hori-zontally on the target, with the ront sight dot centered between the rear sight dots, theoperator can quickly and easily engage the target with a high degree o accuracy.

The rear sight can be adjusted or windage by driting the sight to the let or to the right,depending on the desired shot placement. Bullet impact on target will move in the samedirection that the rear sight is moved. Be careul not to damage the slide inish when ad-justing the rear sight.

Adjustments or elevation are accomplished by exchanging the ront sight with a higheror lower sight. The height o the ront sight is indicated on the bottom o the sight blade.The ront sight must be removed by using a drit punch or an HK-approved sight pusher(contact HK Customer Service Sta or more inormation).

To raise the bullet impact on target, a shorter ront sight is installed. To lower the bulletimpact on target, a taller ront sight is installed. Installing the next higher or lower rontsight will change the point-o-impact 2 inches at 25 meters, depending on the ammunitionused. P Series pistols are unction ired and zeroed at the actory at 25 meters, point-o-aim, point-o-impact. Your actual zero may vary depending on the ammunition used and/or your style o shooting.


17/44

17

SeCTiON 4 AMMUNiTiON

WArNiNG: HK spccally dsclams any sponsblts o any damag o nuythat should occu bcaus o, o as a sult o, th us o aulty, manuactud, oloadd (hand loadd) ammunton, o o catdgs oth than thos o whch th

pstol was ognally chambd o.

The HK P Series pistol is designed to re quality, actory-loaded ammunition, loaded toNATO or SAAMI specications or use specically in handguns.

The ollowing guidelines should be considered when selecting the correct ammunition oryour pistol:

1. Be sure the ammunition you have chosen is compatible with your pistol-proper caliber,cartridge, bullet weight, etc. Caliber markings on the P Series pistol appear on the let

side o the slide and on the barrel locking block, visible through the ejection port on theright side o the slide.

2. Prior to loading the magazine and chamber, careully inspect all cartridges or the ol-lowing abnormalities:

Cracked, split, dirty or corroded cases Improperly seated projectiles and/or primers Damaged projectiles.

3. Do not attempt to ire a cartridge in which the projectile has been orced back into the

case. Upon iring, this condition may result in increased chamber pressure above saelimits.

4. Do not ire ammunition through a pistol that: Is foreign and/or outdated military surplus Is assembled with corrosive primer and/or propellant Is exposed to oil, grease, water or direct sunlight. If possible, remove contaminants

beore use and cool down ammunition exposed to direct sunlight or heat. (Expo-sure to sources o heat could raise the chamber pressure o the cartridge above saelimits.)

Is loaded specifically for use in submachine guns.

CAUTiON: HK ams a dsgnd to uncton wth qualty, manuactud bass-casd ammunton. Us o stl o alumnum-casd catdgs s not commndd andcould advsly act sa and labl unctonng. Us o cast-lad bullts s also notcommndd.

NOTe: Us o +P and +P+ ammunton acclats wa and ducs th svcl on th componnt pats o any pstol, ncludng th P Ss pstols, and s not

commndd. Fo uth nomaton on ammunton slcton, contact HK CustomSvc at 706-568-1906.


18/44

18

SeCTiON 5 iNSTrUCTiONS FOr USe

FiLLiNG AND eMPTYiNG THe MAGAziNe

NOTe: Do not attmpt to load mo than th pscbd numb o catdgs ntoth magan. Do not alt th shap o th magan housng, ollow o spng. To

do so may caus stoppags o th magan may not sat poply n th pstol.

Fllng th Magan

Figure 5

1. Hold the magazine in the non-iring hand with the back side o the magazine restingagainst the palm.

2. Using the iring hand, hold a cartridge between the index inger and thumb with theprojectile acing the palm.

3. Press the rim o the cartridge down against the orward edge o the magazine olloweror on the top cartridge already in the magazine.

4. Slide the cartridge back into the magazine under the eed lips.5. Repeat steps 1-4 until the magazine is full. The viewing holes in the back of the maga-

zine allow the operator to conirm the number o cartridges present within the maga-zine.

Emptying the Magazine - Exert pressure with a inger on the base o the cartridge and

push each cartridge orward out o the magazine one at a time until the magazine isempty.

LOADiNG

WArNiNG: Focully nstng a loadd magan nto many pstols may caus thpstols sld to clos, chambng a catdg and makng th pstol ady to .Whn nstng a magan, always b su th P Ss s pontd n a sa dctonwth you ngs o th tgg and outsd th tgg guad. Falu to do so couldcaus you to unntntonally th pstol, sultng n sous nuy o dath.

Admnstatv Loadng - Used to initially load the pistol beore it is to be ired.

Slide rearward or orward, chamber empty.

1. Make sure ingers are outside o the trigger guard and the pistol is pointed in a saedirection at all times!

2. Insert magazine - Insert the magazine irmly into the rame. Tug on the magazine toinsure that it is ully seated and engaged.


19/44

19

3. Chamber a cartridge - Chamber a cartridge by depressing the slide release or by pullingthe slide ully to the rear and releasing it. Do not ride the slide orward!

4. Top off - Remove the magazine and top it off by inserting one additional cartridge.5. Replace Magazine - After topping off the magazine, replace it in the pistol and ensure

that it is properly seated and engaged.

FiriNG

WArNiNG1. B su o you tagt and whats bhnd t! A bullt om a pstol tavls as a asa ml. it can asly pntat wood o plastboad walls o vn a ca doo.2. B su that you hands and all pats o you body a kpt away om th mulo you pstol at all tms!3. Always wa y and a potcton whn ng th pstol.

Double-action only mode - (Hammer uncocked)1. Aim - Aim at the target.2. Fire - Fire the pistol by pressing the trigger straight to the rear with gradually increasing

pressure.

NOTe: Th P2000/P2000SK s n th doubl-acton only mod and ts hammwll automatcally tun to th uncockd poston ach tm th sld tuns to tsowad poston and th tgg s lasd.

DA/SA action mode - (Hammer cocked)1. Aim - Aim at the target2. Fire - Fire the pistol by pressing the trigger straight to the rear with gradually increasing

pressure.

NOTe: in th DA/SA mod, th P Ss pstols n doubl-acton mod o th stound. At th st ound, th hamm wll automatcally tun to th cockd postonach tm th sld tuns to ts owad poston and th tgg s lasd.

UNLOADiNG - To unload the pistol, ollow the Clearing procedure.

Clearing the Pistol - The P Series pistol is not considered clear or sae unless:1. The magazine is removed rom the pistol.

2. The slide is locked to the rear.3. The chamber is ree o brass or ammunition.

To Clear the HK P Series:1. Make sure ingers are outside o the trigger guard and the pistol is pointed in a sae

direction at all times!2. Remove magazine - Depress the magazine release lever and remove the magazine from

the pistol.3. Open and lock slide - While pointing the pistol in a sae direction, lock the slide open by

pulling the slide rearward as you press the slide release upward. Watch or a cartridge orempty case to be ejected rom the pistol.

4. Inspect chamber - Inspect chamber or the presence o a cartridge or empty case by: Visually viewing chamber through open ejection port. Physically inserting finger into chamber through ejection port to check for the pres-

ence o a cartridge or empty case.Remove any cartridges or empty cases from the chamber or from within the pistol.

The HK P Series pistol is now considered Clear.


20/44

20

I the pistol ails to ire, clear and disassemble it and check or:1. Obstructions in the chamber, bore or frame. Remove obstructions.2. Bad ammunition. Try new ammunition.3. Damaged magazine. Replace magazine.4. Fouling or lack o lubrication. Clean and lubricate the pistol in accordance to the instruc-

tions contained within this manual.

5. Evidence o severely worn or broken parts. Contact HK or your unit armorer.

I your pistol still ails to operate correctly, contact your unit armorer, authorized HK dealer,or HK's Customer Service Department or guidance.

WArNiNG: i a catdg s assmbld wthout powd (a ault o th manuactungpocss), th pm alon has nough pow to popl th bullt nto th bo. Abullt lodgd n th bo may caus damag to th bal and/o pstol anothcatdg s d and could caus psonal nuy o vn dath. Ths vnt scommonly calld a squb load o pop and no kck, and s chaactd by aducd pot and lttl o no movmnt o th sld. An alt opato could notcth occunc o ths vnt n tm to avod ng th nxt catdg.

SeLeCTiON AND USe OF A HOLSTer

Selection - When selecting a carrying holster or the HK P Series pistols, it is important toconsider the ollowing points:

1. The holster must not make contact with or actuate any o the operating controls. Thisincludes the hammer, slide release, magazine release lever, and most

importantly the trigger. The design o the holster must also not actuate these controlswhen the pistol is carried in, drawn rom or returned to the holster.

2. The holster should not cause the slide to move (unlock) when the pistol is returned tothe holster.

3. Accommodations must be provided in the holster or any accessories that might bepresent on the pistol.

4. Choose a holster designed speciically or a P Series pistol. A list o manuacturers thatmake holsters or a variety o HK pistols is available at the Heckler & Koch website or bycontacting HK Customer Service.

rtunng th pstol to th holst - The P Series pistol must be made Sae (or cleared)prior to returning it to the holster. The pistol is considered sae to return it to the holsterwhen:

1. All ingers are o o the trigger and out o the trigger guard.2. The pistol is clear.3. In DA/SA mode, the saety is on.

WArNiNG: Th pstol must nv b tund to th holst unlss th abovpocdus hav bn ollowd o nuy o dath could occu.

STOrAGe AND TrANSPOrT1. Store or transport the pistol and its components clean and lubricated.2. Store and transport the pistol without cartridges in the chamber, magazine or in the

storage container.3. Store and transport the pistol with the slide orward and the hammer down (uncocked).4. Clean and lubricate the pistol and its components at least every twelve (12) months dur-

ing storage.


21/44

21

5. Store the pistol and its components in a clean, dry, dust-ree environment with regulatedtemperature controls.

6. Store the pistol and ammunition separately under lock and key.

Long-Tm Pstol Stoag - Anytime the slide is moved ully rearward on the P Series, thehammer spring is compressed and held in that position until the cocking piece is released

by pulling the trigger on the pistol. Thereore, or long-term storage (more than 1 year),it is suggested that the pistol rst be CLEARED (refer to page 3) and made safe, thenpointed in a sae direction and dry red to release pressure on the hammer spring to main-tain its lie span. Store magazines empty to maintain maximum spring lie span.

NOTe: Fo optmal long-tm stoag, cla th P Ss and las pssu on thcockng pc and hamm spng by dy ng th pstol on tm.

iNTerCHANGeABLe BACKSTrAPS

Figure 6Extra Large, Large, Medium (standard), & Small Backstraps

Backstrap removal for all P Series pistols - Ensure the pistol is CLEAR and decocked (seepage 3) and the magazine is removed. Dry ring the pistol will relieve any tension on thehammer spring prior to removal o the grip panel. With an appropriate metal punch, care-ully tap out the lanyard loop roll pin (Figure 7).

Extract the pin once it is protruding rom the rame. When the pin is removed, the grippanel can be slid downward o the rame (Figure 8). Take care that the hammer strut andhammer spring do not all out o the rame and become lost or damaged.

Figure 7 Figure 8

Backstrap installation or all P Series pistols - Ensure the hammer strut and hammer springare properly positioned on the back o the rame (Figure 9). Place the replacement grip


22/44

22

panel on the back o the rame, approximately 1 inch (2.54cm) lower than its assembledposition (Figure 10), and push the grip panel up onto the grip rails.

Figure 9 Figure 10

Continue pushing the grip panel upward on the rame. As the grip panel slides upwardonto the grip rails, the hammer spring will compress slightly creating resistance. Continueto slide the grip panel upward until it ts fush and there is no gap between the top o thegrip panel and rame.

At this point, the pin holes on the grip panel and the rame will line up. Careully reinsertthe pin and push it through the grip panel and rame using nger pressure (Figure 11).

With the pin properly aligned in the grip panel and the rame, careully tap the pin until itis ully seated and centered in the rame (Figure 12).

Figure 11 Figure 12

Hold the Grip Panel in place while Careully tap the pin all the way back in.Inserting the pin.

CAUTiON: B caul not to damag th P Ss whn movng and nstallngbackstaps o gps panls.

intchangabl Sd Panls and Backstaps - P30 Pstol OnlyThree easily exchangeable back strap inserts/ grip shells o dierent heights enable a per-

ect adaptation o the weapon to diering hand sizes. Exchange o back strap inserts/ gripshells is reserved o weapon mechanics/ shooting trainer.


23/44

23

Figure 13

Grip panels and backstraps (L-M- Standard)

rmovng th Gp Panls - First, ollow the instructions or removing the P Series back-strap. Once the back strap has been removed, the side panels will easily slide horizontallyaway rom the rame o the pistol.

installng th Gp Panls - First choose the grip panels which best ft your hand. Thenslide the grip panel horizontally into the grip slot. The grip panel will ft securely. Then,ollow the instructions or installing the backstrap.

Figure 14Once the backstrap is removed, simply slide grip panels o the rame.


24/44

24

SeCTiON 6 DiSASSeMBLY AND ASSeMBLY

Clear the pistol by ollowing the directions on the inside cover

Dsassmbly (Fld Stppng) o pstol

1. Make sure the pistol is CLEAR.2. Depress the slide release and allow the slide to move orward.3. Using the iring hand, retract and hold the slide to the rear so that the axle o the slide

release is visible through the recess in the let side o the slide(see Figure 15).

4. With the non-iring hand, completely remove the let slide release rom the let side othe rame by pressing on the axle o the slide release rom the right side o the rame.The right slide release will remain attached to the rame.

Figure 15

5. Remove the slide with barrel and recoil spring assembly by sliding it forward off of therame (see Figure 16 below).

Figure 16

6. Careully remove the recoil spring assembly rom the barrel and slide by liting up on

the rear o the recoil spring guide rod. The entire assembly can now be lited out o theslide (see Figure 19).

7. Remove the recoil spring assembly. The P Series pistol uses a captive recoil springassembly. Disassembly o the recoil spring is not recommended.

8. Lit the rear o the barrel by the locking block and withdraw it rom the slide.9. Remove the right slide release by rotating it upward approximately 45 and lifting it out

o the rame.


25/44

25

Dsassmbly o th P30/P30L1. Make sure the pistol is CLEAR.2. Depress the slide release and allow the slide to move orward.3. Using your right hand, retract and hold the slide to the rear so that the slide release axle

lines up with the orward square cutout (arrow) on the slide. (See Figure 17)

Figure 17

4. With the let hand, press the slide release axle rom the right to the let until the redindicator is showing. (See Figure 18) Then remove the slide with the barrel and recoilspring assembly by sliding it orward o the rame.

Figure 18

CAUTiON: it s not ncssay to mov th sld axl byond ths pont and dongso could damag th pstol.

5. Remove the slide with barrel and recoil spring assembly by sliding it forward off of therame (see Figure 16).

6. Careully remove the recoil spring assembly rom the barrel and slide by liting up onthe rear o the recoil spring guide rod. The entire assembly can now be lited out o theslide (see Figure 19).

7. Remove the recoil spring assembly. The P Series pistol uses a captive recoil springassembly. Disassembly o the recoil spring is not recommended.

8. Lit the rear o the barrel by the locking block and withdraw it rom the slide.


26/44

26

Figure 19

NOTe: Dsassmbly o th pstol s now complt. Only an HK ctd amoshould dsassmbl th pstol uth.

Pstol Assmbly1. Install the right slide release into the recess located on the right side o the rame and

rotate it downward until it is parallel to the top o the rame.2. Position the barrel in the slide so that: The muzzle of the barrel fits in the hole in the front of the slide. The locking block portion of the barrel fits within the ejection port and the angled lock-

ing suraces o the locking block are visible along the bottom o the slide.3. Install the recoil spring assembly into the slide so the ront o the recoil spring guide rod

engages in the small hole provided in the ront o the slide.4. Align the opposing angled locking suraces on the rear end o the recoil spring guide

rod with those located on the bottom o the barrel locking block (see Figures 20 & 21).5. Push the rear o the recoil spring assembly orward enough so that the recoil spring

retainer can be engaged on the shel provided on the ront o the barrel locking block(see Figure 20, 21, & 22).

Figure 20 (relationship o recoil springassembly to barrel locking block inside o slide)

Figure 21 (recoil spring assembly and barrelproperly positioned in the slide)

6. Hold the slide in the non-iring hand with the thumb holding the rear end o the recoilspring assembly in place on the slide.


27/44

27

Figure 22

7. Check the position o the sear axle on the rame. Ensure that it does not protrude romeither side o the rame.

8. Hold the rame in the iring hand. Position the rear o the slide above the ront edge othe rame.

9. Slowly draw the slide back onto the rame so that the metal inserts in the rame it intothe grooves on the inside o the slide (see Figure 23).

Figure 23

10. Retract the slide to the point where the recess in the left side of the slide is positionedover the hole where the axle o the slide release will go and hold it there.

11. Insert the slide release rom let to right into the rame until it is lush with the side othe rame.

NOTe: Assmbly o th pstol s now complt. Cla th pstol and chck t ococt assmbly and opaton. B su th sld movs ly on th am andwth th pstol clad and pontd n a sa dcton, nsu all contols opat

coctly. As applcabl, chck doubl-acton only mod, sld las, and thmagan las.


28/44

28

MAGAziNe DiSASSeMBLY

NOTe: Only P2000 (not th P2000SK o P30) modls us wdly avalablUSP Compact magans. A vaty o USP Compact magans a n us, ncludngthos wth xtndd and fat fooplats wth hgh capacty and 10-ound capacty,USP Compact 9mm magans wth a 13-ound capacty and USP Compact .40

magans wth a 12-ound capacty. USP Compact 9mm and .40 S&W maganswth a 10-ound capacty a also avalabl.

NOTe: euopan P2000 magans wll not t th P2000 modl.

Figure 24a 10-round Figure 24b

and high-capacity magazines

CAUTiON: Bwa o th spng tnson xtd by th magan spng whlmovng and nstallng th magan fooplat. Kp th bas o th magan

pontd n a sa dcton (away om th ac and ys) at all tms dung dsas-smbly and assmbly and wa y potcton.

Dsassmbly o hgh-capacty magans1. Using a blunt, pointed instrument, depress the locking detente located in the loorplate

and hold it there (see Figure 24b).2. Place a portion o either hand over the base o the magazine to control the release o

the magazine spring and locking plate.3. Slowly slide the loorplate orward o o the magazine housing.4. Gradually allow the locking plate and magazine spring to expand out o the magazine

housing (see Figure 25).5. Remove the locking plate, magazine spring and magazine follower from the magazine

housing.

Figure 25 Figure 26Locking plate and spring Magazine spring and ollower


29/44

29

Dsassmbly o 10-ound magans:1. Using a blunt, pointed instrument, depress the locking insert detente located in the

loorplate and hold it there (see Figure 24b).2. Place a portion o either hand over the base o the magazine to control the release o

the magazine spring and locking insert.3. With the locking insert detent still depressed, squeeze the loorplate locking tabs lo-

cated on the right and let sides o the magazine.

Figure 27 Figure 28P2000/USP Compact

10-round magazine disassembled

4. Gradually allow the locking insert and magazine spring to expand out o the magazinehousing (see Figure 27).

5. Remove the locking insert, magazine spring and magazine follower from the magazinehousing.

MAGAziNe ASSeMBLY

Figure 29

1. Place the magazine ollower onto the magazine spring with the end o the spring posi-tioned on the let o the ollower.

2. Insert the ollower and magazine spring into the magazine housing as depicted in Figure29.

3. Place the locking plate or locking insert on magazines onto the protruding end o themagazine spring so that the rounded corners ace toward the ront o the magazine.


30/44

30

4. Push the locking plate down into the magazine housing against the pressure o themagazine spring and hold it there.

5. On 10-round magazines, push the loorplate up onto the base o the magazine housinguntil the locking tabs engage in the sides o the housing.

6. Check to see i the locking tabs on the loorplate are securely locked into the housingand the locking detent on the locking plate its within the hole in the loorplate.

On all magazines, check the magazine or proper assembly by insuring that the ollowerslides up and down reely within the magazine housing and with spring tension. Also checkthat the magazine ollower rises within the magazine housing to be nearly fush against thebottom o the magazine eed lips.


31/44

31

SeCTiON 7 CLeANiNG & MAiNTeNANCe

NOTe: Th svc l and pomanc o you HK P Ss pstol s dpndntupon th coct handlng and pop ca by th opato.

Matals rqud - At a minimum, we suggest the ollowing materials to properly cleanthe P Series:

Cleaning rod with handle and patch holder Nylon toothbrush Bronze bristle bore brush (in the appropriate caliber) Cleaning patches (in the appropriate caliber) Lint-free wiping rag Cleaning solvent/lubricant Cotton swabs

CAUTiON: Us saty goggls whn usng solvnts and xcs ca usngcompssd a.

HK Handgun Cleaning Kits, #701956 (9mm & .357SIG), #701957 (.40 S&W), and #701958(.45ACP) are available rom HK or thorough cleaning o HK pistols and other irearms.

Clanng intvals - Normal and Major are the two types o operator cleaning or the PSeries pistol.

Nomal Clanng - Perormed ater each iring or every twelve (12) months.

Mao Clanng - Oten reerred to as detailed cleaning. Perormed ater the iring o 500cartridges or when the pistol is exposed to, or laden throughout, with sand, dust, water (es-pecially salt water) or other visible contaminants or oreign matter.

Nomal Clanng

CAUTiON: Do not use a stanless steel boe bush whch can scatch the polygonalboe and educe accuacy.

Sld - Gently scrub all internal surfaces of the slide using the nylon toothbrush moistened with

solvent. Remove all loose fouling from all surfaces of the slide using a rag and cotton swabs.rcol spng assmbly - Remove all visible fouling using solvent, a nylon toothbrush or a rag and cotton swabs.Bal (wth lockng block) - Moisten a bronze bore brush with solvent and scrub the bore from chamber to muzzle at

least six (6) passes, back and orth. Remove the loose fouling from the bore using cleaning patches. Gently scrub the exterior o the barrel and locking block with the nylon toothbrush moist-

ened with solvent. Remove all loose fouling from the exterior of the barrel using a rag and

cotton swabs.Fam - Gently scrub all internal surfaces where carbon fouling is present using the nylon tooth-

brush moistened with solvent. Concentrate on the area normally covered by the slide. Using a rag and cotton swabs, remove all loose fouling from all areas of the frame.


32/44

32

Magan - Gently scrub the top of the magazine, concentrating on the follower and feed lips, using

the nylon toothbrush moistened with solvent. Using a rag and cotton swabs, remove all loose fouling from all surfaces of the magazine.

Mao Clanng - Major Cleaning is the same as normal cleaning except that:

The magazine is disassembled for cleaning. All parts should be rinsed with or immersed in solvent and thoroughly scrubbed with a

nylon brush. The parts can then be dried using compressed air or with a rag and cottonswabs.

NOTe: All pats o th P Ss pstol can b mmsd n any clanng solvnt thats sa to put you hands nto, ncludng ultasonc clanng soluton. Us o ultasoncclanng machns can sult n th unwantd moval o colod nc makngso th am, xtacto and contol lv (wh applcabl).

iNSPeCTiONDuring and ater cleaning, visually inspect the pistol and its components or any irregulari-ties that may cause problems or stoppages during operation. Generally, you should keep awatchul eye out or the discrepancies listed below.

Always cla th pstol bo conductng you nspcton!Check or:

Damaged or missing parts Improper assembly or function Absence of free movement, where applicable Absence of spring tension, where applicable

Unaccustomed looseness Parts exhibiting signs of cracks, burrs, dents or obvious signs o damage or stress Presence of stops or tactile clicks, where applicable General overall cleanliness Presence of sufficient lubrication Presence o corrosion or degradation o surace inish.

CAUTiON: Ths pstol has bn dvlopd by capabl and xpncd ngns.its psnt dsgn psnts an optmaton o a combnaton o saty, spd odploymnt, accuacy, dpndablty and duablty. Do not attmpt to mak ths

pstol btt by altng any o ts componnts. Altng any pat o th pstol omagan may caus nuy o dath and wll also vod any HK waanty on th pod-uct.

LUBriCATiON

Metal suraces o the P Series pistol are treated with HKs special corrosion and wear-resis-tant inish. This surace treatment does not completely reduce the riction between movingparts and it is recommended that a lubricant be applied to the pistol to ensure proper unc-tioning. Any type o high-quality, medium-weight lubricant (oil) speciically designed or use

on irearms will work well on the P Series. Do not use lubricants that boast o their ability topenetrate metal as these substances may deaden primers.

Wh and How Much -

No Lub - Surace is dry and not slippery to the touch. All plastic and rubber components


33/44

33

Lght Lub - A inger run across the surace yields little or no lube. Bore, chamber and exterior of barrel All metal parts All internal parts in slide and frame Magazine spring Recoil spring assembly

Sights P Series pistol metal magazine housing, where applicable

Mdum Lub - A inger run across the surace yields some lube, but lube does not rundown surace when it is held in a vertical position.

Barrel locking block Slide rails and grooves All operating controls Locking insert and guiding part in frame Extractor

Havy Lub - Lubrication runs down the surace when it is held in a vertical position.

No havy lub s qud on th HK P Ss pstol.

Re-apply lubricant periodically during firing as it burns off from the heat. Apply lubricantusing a clean shaving brush, cotton swabs, patches or rag. A spray bottle o lubricant alsoworks well when using compressed air to circulate the lubricant into all parts and to removethe excess rom the pistol.

TrOUBLeSHOOTiNG PrOBLeMS AND rePAir

Common causes o problems that are oten overlooked include:

Fouled or improperly lubricated pistol Bad ammunition Damaged magazines Operator error

I your P Series pistol still ails to unction, please contact HK Customer Service at 706-568-1906 for the name and address of your nearest HK Authorized Repair Facility. Law enforce-ment users, contact your unit armorer or HK Customer Service.

NOTe: i at vwng ths manual you stll hav qustons, plas contact HKCustom Svc at 706-568-1906 o by mal: [email protected].


34/44

34

LOCK-OUT DeViCe

P Series pistols are equipped with a patented HK Lock-Out device. This componentreplaces the lanyard loop insert in the rame and when engaged, locks the handgunsaction by blocking any movement o the trigger, the hammer and the slide. The handgunis locked and cannot re until unlocked. The Lock-Out control plate is accessible through

the pistols magazine well (see Figure 30).

Figure 30

Turning the key clockwise 1/4 turn locks the action,turning it counter-clockwise unlocks the action.

Clear the pistol and dry re it prior to activating the Lock-Out device. Use the two prongedkey supplied with the pistol to lock or unlock the pistol as desired. When the holes on theLock-Out device are horizontally positioned, the pistol is locked and cannot be red (seeFigure 31).

Figure 31 Figure 32

Locked position Unlocked/fre position

When the holes on the Lock-Out device are vertically positioned, the pistol is unlockedand can be red (see Figure 32).

WArNiNG: Th HK Lock-Out dvc s not a substtut o sa gun handlngpactcs. Nv pont th mul o th pstol n an unsa dcton (at yousl ooths). Whn th Lock-Out dvc s placd n th lockd poston, th sld s lockdn th closd poston and cannot b movd! Focng th sld awad whl thgun s n ths lockd poston wll damag th pstol.

For more inormation contact HK Customer Service.


35/44

35

P SerieS ACCeSSOrieS

The addition o industry standard mounting rails to P Series models (including a ull Picat-inny rail on the P30 and P30L), allows the widest variety o lights, laser aimers and acces-sories to be added by simply sliding them onto the open rail system.

Figure 33 Figure 34Light mounted on P2000 Detail o P2000 mounting rails

Follow the instructions o the manuacturer or installing, operating and removingaccessories rom the mounting rails. Always ensure the P Series is clear and unloadedbeore installing or removing accessories. Slide the accessory onto the rails until it locksinto the locking slot located on the bottom o rame.

Figure 35Slide the accessory onto the rails

CAUTiON: impoply dsgnd o nstalld accssos may sult n damag to thmountng goovs and/o th pstol. Such damag s not covd und waanty. Bctan to us only HK appovd accssos and ollow nstallaton and pcautonscaully.

For a complete list o accessories that t the P30/ P30L and P2000/P2000SK Series,contact the HK Customer Service Sta at Tel: 706-568-1906, Email: [email protected].


36/44

36

1 Barrel .40 S&W . . . . . . . . . . . . . . . . . 207164

Barrel 9mm x 19 . . . . . . . . . . . . . . . . 218550

Barrel .357 SIG . . . . . . . . . . . . . . . . . 202685

* Recoil spring assembly complete

.40 S&W (Items 2-5) . . . . . . . . . . . . . 207188


9mm (Items 2-5) . . . . . . . . . . . . . . . . 209258


.357 SIG (Items 2-5) . . . . . . . . . . . . . 207188

2 Recoil spring guide rod. . . . . . . . . . . 209307

3 Absorber bushing. . . . . . . . . . . . . . . 215932

4 Recoil spring .40 S&W . . . . . . . . . . . 215830

Recoil spring 9mm . . . . . . . . . . . . . . 215852

Recoil spring .357 SIG. . . . . . . . . . . . 215830

5 Recoil spring retainer . . . . . . . . . . . . 215831* Slide (complete) .40 S&W. . . . . . . . . 207225

* Slide (complete) .9mm . . . . . . . . . . . 207312

* Slide (complete) .357 SIG . . . . . . . . . 202686

6 Slide .40 S&W . . . . . . . . . . . . . . . . . . 207165

Slide 9mm . . . . . . . . . . . . . . . . . . . . . 207280

Slide .357 SIG . . . . . . . . . . . . . . . . . . 202687

7 Front sight. . . . . . . . . . . . . . . . . . . . . 979073

8 Rear sight . . . . . . . . . . . . . . . . . . . . . 979072

9 Rubber plug, extractor . . . . . . . . . . . 209294

10 Extractor spring. . . . . . . . . . . . . . . . . 218315

11 Extractor . . . . . . . . . . . . . . . . . . . . . . 218314

12 Roll pin for extractor ISO 3x14 . . . . . 98083813 Firing Pin Spring . . . . . . . . . . . . . . . . 215822

14 Firing pin. . . . . . . . . . . . . . . . . . . . . . 209295

15 Firing pin block spring . . . . . . . . . . . 209962

16 Firing pin block . . . . . . . . . . . . . . . . . 209313

17 Frame incomplete (.40, 9mm, .357) . 207198

18 Trigger axle . . . . . . . . . . . . . . . . . . . . 214154

19 Trigger . . . . . . . . . . . . . . . . . . . . . . . 209263

20 Trigger rebound spring. . . . . . . . . . . 219441

21 Flat spring . . . . . . . . . . . . . . . . . . . . . 219167

22 Trigger bar detent spring . . . . . . . . . 209270

23 Trigger bar detent . . . . . . . . . . . . . . . 209269

24 Trigger bar . . . . . . . . . . . . . . . . . . . . 207331

25 Magazine disconnect axle. . . . . . . . . 207193

26 Magazine disconnect lever . . . . . . . . 207167

27 Magazine disconnect spring. . . . . . . 207194

28 Hammer axle. . . . . . . . . . . . . . . . . . . 209272

29 Sear. . . . . . . . . . . . . . . . . . . . . . . . . . 209320

* Decocker for V3 . . . . . . . . . . . . . . . . 209261

30 Catch. . . . . . . . . . . . . . . . . . . . . . . . . 209273

31 Sear actuator latch . . . . . . . . . . . . . . 209274

32 Sear axle . . . . . . . . . . . . . . . . . . . . . . 214101

33 Disconnector. . . . . . . . . . . . . . . . . . . 209271

34 Hammer . . . . . . . . . . . . . . . . . . . . . 209321

35 Cocking piece . . . . . . . . . . . . . . . . . . 209265

36 Cocking piece spring . . . . . . . . . . . . 20927537 Hammer strut . . . . . . . . . . . . . . . . . . 209312

38 Hammer spring . . . . . . . . . . . . . . . . . 214695

39 Grip panel with HK Lock-Out

device, complete Size M. . . . . . . . . . 207192

* Grip Panel with HK Lock-Out

device Size S . . . . . . . . . . . . . . . . . . . 207281

* Grip Panel with HK Lock-Out

device Size L . . . . . . . . . . . . . . . . . . . 207283

* Grip panel with HK Lock-Out

device Size XL . . . . . . . . . . . . . . . . . . 207285

40 Roll pin for grip panel (ISO 3x20) . . . 985014

41 Magazine release spring. . . . . . . . . . 215929

42 Magazine release . . . . . . . . . . . . . . . 214818

43 Shaped spring. . . . . . . . . . . . . . . . . . 214171

44 Slide release (let side) . . . . . . . . . . . 209267

45 Slide release (right side) . . . . . . . . . . 209268

46 Magazine housing (.40 cal., 10-rd) . . . 215833

* Magazine housing (9mm, 10-rd.) . . . . 215848

47 Follower (.40 caliber, 9mm). . . . . . . . 21583648 Magazine spring (.40, 9mm, 10-rd.) . . 214850

49 Locking plate (9mm 10-rd.). . . . . . . . 215850

Locking plate (.40 S&W) . . . . . . . . . . 215835

50 Extended loorplate (9mm, 10-rd.) . . 215983

* Extended loorplate (.40 cal. 10-rd.) . . . 215978

* Flat Floorplate (9mm, 10-rd.) . . . . . . 215849

* Flat Floorplate (.40 cal., 10-rd.). . . . . 215834

51 Magazine housing (9mm, 13-rd) . . . . . 215846

* Magazine housing (.40 cal., 12-rd) . . . 215661

* Magazine housing (.357, 13-rd) . . . . . 217816

52 Magazine spring (9mm 13-rd, .357 12-rd.) . . . 214212

Magazine spring ( .40 12-rd.). . . . . . . . . . . . 21858753 Locking plate (9mm & .357 13-rd,

.40 S&W 12-rd). . . . . . . . . . . . . . . . . . . . 215844

54 Extended loorplate (9mm, 13-rd.) . . . . 215980

Extended loorplate (.40 cal. 12-rd.) . . . 215663

Extended loorplate (.357 13-rd.) . . . . . 201184

* Floor plate (9mm, 13-rd.) . . . . . . . . . . . 215843

* Flat Floor plate (.40 cal.,12-rd.) . . . . . . . 215662

55 Magazine complete (13-rd, 9mm, with

extended floorplate) . . . . . . . . . . . . . . . . 215981

Magazine complete (12-rd, .40, with

extended floorplate) . . . . . . . . . . . . . . . . 217439

Magazine complete (13-rd, .357, with

extended floorplate)* . . . . . . . . . . . . . . . 217818

* Magazine complete (10-rd, .40 cal.) . . . 215832

* Magazine complete (10-rd, .40 cal., with


* Magazine complete (12-rd, .40 cal.) . . . 217438

* Magazine complete (12-rd, .40 cal., with


* Magazine complete (10-rd, 9mm). . . . . 215847

* Magazine complete (10-rd, 9mm, with


* Magazine complete (13-rd, 9mm). . . . . 215845

* Items not pictured in exploded view onopposite page

SeCTiON 8 PArTS LiST P2000 (.40 S&W, 9 MM, .357 SiG)

Item Description Identiication No. Item Description Identiication No.


37/44

37

Figure 36P2000 Exploded Diagram


38/44

38

PArTS LiST P2000SK SUBCOMPACT (9 MM, .40 S&W, .357 SiG)

Itm Dscpton idntcaton No. Itm Dscpton idntcaton No.

1 Barrel (9mm x19) . . . . . . . . . 207120

Barrel (.40 S&W) . . . . . . . . . 207319Barrel (.357 SIG) . . . . . . . . . 202688

2 Recoil spring assembly,complete . . . . . . . . . . . . . . . 207119

* Slide, complete (9mm x19) . 207221Slide, complete (.40 S&W) . 207321Slide, complete (.357 SIG). . 202689

3 Slide (9mm x19). . . . . . . . . . 207124Slide (.40 S&W) . . . . . . . . . . 207322Slide (.357 SIG) . . . . . . . . . . 202690

4 Front sight . . . . . . . . . . . . . . 9790735 Rear sight . . . . . . . . . . . . . . 979072

6 Rubber plug, extractor . . . . 2092947 Extractor spring. . . . . . . . . . 2183158 Extractor . . . . . . . . . . . . . . . 2183149 Roll pin for extractor . . . . . . 980838

Roll pin for firing pin . . . . . . 98083810 Firing pin spring . . . . . . . . . 21582211 Firing pin . . . . . . . . . . . . . . . 20929512 Firing pin block spring. . . . . 20996213 Firing pin block . . . . . . . . . . 209313* Frame, complete. . . . . . . . . 207318

14 Frame . . . . . . . . . . . . . . . . . 20720015 Trigger axle . . . . . . . . . . . . . 21415416 Trigger . . . . . . . . . . . . . . . . . 20926317 Trigger rebound spring . . . . 21944118 Flat spring . . . . . . . . . . . . . . 21416719 Trigger bar detent spring . . 20927020 Trigger bar detent. . . . . . . . 20926921 Trigger bar. . . . . . . . . . . . . . 20733122 Hammer axle . . . . . . . . . . . . 20927223 Sear . . . . . . . . . . . . . . . . . . . 209320 Decocker for V3. . . . . . . . . . 209261

24 Catch . . . . . . . . . . . . . . . . . . 20927325 Sear actuator latch . . . . . . . 20927426 Sear axle . . . . . . . . . . . . . . . 214101

27 Disconnector . . . . . . . . . . . . 209271

28 Hammer. . . . . . . . . . . . . . . . 20932129 Cocking piece . . . . . . . . . . . 20926530 Cocking piece spring . . . . . 20927531 Hammer strut . . . . . . . . . . . 20712132 Hammer spring . . . . . . . . . . 20712233 Backstrap M (Medium) . . . . 207222* Backstrap L (Large) . . . . . . . 202604

34 Roll pin for backstrap . . . . . 98402335 Magazine release spring . . . 21592936 Magazine release . . . . . . . . 21481837 Shaped spring or slide

release . . . . . . . . . . . . . . . . . 214171

38 Slide release . . . . . . . . . . . . 20926739 Slide release, right. . . . . . . . 209268* Magazine, complete

(9mm) . . . . . . . . . . . . . . . . . 207161* Magazine, complete

(.40 S&W). . . . . . . . . . . . . . . 207323* Magazine, complete

(.357 SIG). . . . . . . . . . . . contact HK40 Magazine housing

(9mm, .357 SIG). . . . . . . . . . 207162Magazine housing(.40 S&W). . . . . . . . . . . . . . . 207214

41 Follower (9mm, .40 S&W, .357 SIG)215836

42 Magazine spring (9mm, .40 S&W,.357 SIG) . . . . . . . . . . . . . . . 207218

43 Locking plate(9mm, .357 SIG). . . . . . . . . . 202693Locking plate (.40 S&W) . . . 215844

44 Floorplate (9mm, .40 S&W,.357 SIG) . . . . . . . . . . . . . . . 207216


39/44

39

Figure 37P2000SK Subcompact

Exploded Diagram


40/44

40

PArTS LiST P30

Item Description Identiication No. Item Description Identiication No.

Barrel, complete (Items 1-5)1 Barrel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 308

Recoil spring, compl. (Items 2-5) . . . . . . . . 234 319

2 Recoil spring guide rod. . . . . . . . . . . . . . . 234 3103 Stop sleeve . . . . . . . . . . . . . . . . . . . . . . . . 215 9324 Recoil spring . . . . . . . . . . . . . . . . . . . . . . . 215 8525 Recoil spring stop disc . . . . . . . . . . . . . . . 215 831 Slide, compl. (Items 6 - 16) . . . . . . . . . . . . 234 3936 Slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 3097 Front sight, height 5.9 mm . . . . . . . . . . . . 227 7117.1 Front sight, height 6.1 mm . . . . . . . . . . . . 234 3277.2 Front sight, height 6.3 mm . . . . . . . . . . . . 234 3287.3 Front sight, height 6.5 mm . . . . . . . . . . . . 234 3297.4 Front sight, height 6.7 mm . . . . . . . . . . . . 234 3867.5 Front sight, height 6.9 mm . . . . . . . . . . . . 234 3878 Rear sight . . . . . . . . . . . . . . . . . . . . . . . . . 234 3239 Extractor bolt. . . . . . . . . . . . . . . . . . . . . . . 209 29410 Extractor spring . . . . . . . . . . . . . . . . . . . . . 218 31511 Extractor . . . . . . . . . . . . . . . . . . . . . . . . . . 218 31411.1 Extractor or loaded chamber

indicator . . . . . . . . . . . . . . . . . . . . . . . . . 234 32611.2 Loaded chamber indicator . . . . . . . . . . . . 234 32411.3 Compression spring or loaded

chamber indicator . . . . . . . . . . . . . . . . . 234 32512 Roll pin (3x) . . . . . . . . . . . . . . . . . . . . . . . . 988 89113 Firing pin spring . . . . . . . . . . . . . . . . . . . . 215 82214 Firing pin . . . . . . . . . . . . . . . . . . . . . . . . . . 234 65415 Compression spring or drop

saety catch . . . . . . . . . . . . . . . . . . . . . . 209 96216 Drop saety catch (ring

pin saety) . . . . . . . . . . . . . . . . . . . . . . . . 209 313 Frame, complete (Items 17-47). . . . . . . . . 234 65117 Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 38818 Trigger axle . . . . . . . . . . . . . . . . . . . . . . . . 214 15419 Trigger. . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 29720 Elbow spring or hammer . . . . . . . . . . . . . 234 389

21 Lea spring or catches . . . . . . . . . . . . . . . 214 16722 Trigger bar detent spring . . . . . . . . . . . . . 209 27023 Trigger bar detent . . . . . . . . . . . . . . . . . . . 209 26924 Trigger bar. . . . . . . . . . . . . . . . . . . . . . . . . 207 33125 Hammer axle . . . . . . . . . . . . . . . . . . . . . . . 209 27226 Release catch and decocking

lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 261

27 Hammer catch . . . . . . . . . . . . . . . . . . . . . . 209 27328 Control lever . . . . . . . . . . . . . . . . . . . . . . . 234 48729 Cylindrical pin . . . . . . . . . . . . . . . . . . . . . . 234 75830 Disconnector . . . . . . . . . . . . . . . . . . . . . . . 209 27131 Hammer with spur . . . . . . . . . . . . . . . . . . . 209 26232 Cocking piece . . . . . . . . . . . . . . . . . . . . . . 209 26533 Elbow spring or hammer . . . . . . . . . . . . . 209 27534 Hammer spring rod . . . . . . . . . . . . . . . . . . 209 31235 Hammer spring . . . . . . . . . . . . . . . . . . . . . 214 69536 Bearing or hammer spring . . . . . . . . . . . . 234 29537 Cylindrical pin . . . . . . . . . . . . . . . . . . . . . . 970 07438 Grip shell (let) (M) . . . . . . . . . . . . . . . . . . . 234 30339 Grip shell (right) (M). . . . . . . . . . . . . . . . . . 234 30440 Back strap (M) . . . . . . . . . . . . . . . . . . . . . . 234 302

Grip shell (let) (S) . . . . . . . . . . . . . . . . . . . 234 300 Grip shell (right) (S) . . . . . . . . . . . . . . . . . . 234 301 Back strap (S) . . . . . . . . . . . . . . . . . . . . . . . 234 299 Grip shell (let) (L) . . . . . . . . . . . . . . . . . . . 234 306 Grip shell (right) (L) . . . . . . . . . . . . . . . . . . 234 307 Back strap (L) . . . . . . . . . . . . . . . . . . . . . . . 234 30541 Roll pin . . . . . . . . . . . . . . . . . . . . . . . . . . . 978 17042 Compression spring or

magazine release . . . . . . . . . . . . . . . . . . 215 92943 Magazine release . . . . . . . . . . . . . . . . . . . 234 29644 Form spring or slide release. . . . . . . . . . . 214 171

45 Slide release (let) . . . . . . . . . . . . . . . . . . . 202 80546 Slide release (right) . . . . . . . . . . . . . . . . . . 202 80647 Compression spring or recoil

spring guide rod . . . . . . . . . . . . . . . . . . 234 774 Magazine, compl. (Items 48-52) . . . . . . . . 234 31648 Magazine housing . . . . . . . . . . . . . . . . . . . 234 31849 Follower. . . . . . . . . . . . . . . . . . . . . . . . . . . 215 83650 Magazine spring . . . . . . . . . . . . . . . . . . . . 215 11851 Locking plate. . . . . . . . . . . . . . . . . . . . . . . 215 84452 Magazine foor plate . . . . . . . . . . . . . . . . . 234 298

Parts list - P30 V2(as ar as dierent rom P30) Frame, complete (Items 17 - 47) . . . . . . . . 234 40317 Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 29420 Elbow spring or hammer . . . . . . . . . . . . . 234 40526.1 Release catch . . . . . . . . . . . . . . . . . . . . . . 209 32028 Control lever . . . . . . . . . . . . . . . . . . . . . . . 209 27431.1 Hammer without spur . . . . . . . . . . . . . . . . 209 321

Parts list - P30 V3 (SA/DA)(as ar as dierent rom P30) Frame, complete (Items 17 - 47) . . . . . . . 234 40117 Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 29426.1 Release catch . . . . . . . . . . . . . .

pseries ops manual 060809

Documents