progskeet1 1tutorial clip nand alex-07 in progress
TRANSCRIPT
-
ProgSkeet Tutorial 360CLIP
-
Set Up 360Clip-NAND
Hardware: Progskeet 1.1 Injectus 360Clip-NAND
Auxiliary device: 2x USB cable
Software: InfectusProgrammer-3.9.9.0 (Folder "USB-Drivers3.1":Usb drivers to manage
INJECTUS devices under WINDOWS)
ProgSkeet_Bitstreams_111126 (DAT:bitstreams in DAT format (Actel DirectC; Injectus for example) SL_NAND: when using Solderless NAND clip addon)
Zadig.exe (for older ProgSkeet_110819 or Winskeet40000_111004 you need the driver libusb0, for newer Winskeet111205 you select WinUSB with ZADIG.EXE)
-
Bitstream programming solderless NAND
Download from http://www.infectus.biz/downloads.php Open the directory where you have extracted Infectus
Programmer 3.9.9.0
Open now InfectusProgrammer_3.9.9.0.exe
-
Connect injectus on pc usb-port
Connect progskeet on other pc usb-port
both connected to usb
If you get Board not present check device manager if right injectus drivers loaded
-
if injectus detected then can be started
In the Actel Panel, click Load DAT (ProgSkeet_Retail_SL_NAND111126.dat)
-
proceed programming (progress see points)
Programming needs few minutes, wait patiently for DONE!
-
connecting the NAND clip(s) and dump NANDs
Hardware: Progskeet 1.1 360Clip(s)-NAND, flat-cable to subboard (blue mark on same level side) 50 pin flat-cable, subboard
Auxiliary device: 1x USB cable 1x spring clamps (to press on clip) 1x fine cutter 1x cleaning brush 1x soldering iron, solder 2x wire (e.g. awg26) or IDE-cable or CAT5-cable 1x alcohol (isopropyl) cleaning compound
Software: Winskeet111205 (+ driver zadig.exe) , program working on single nand FlowRebuilder v.4.2.1.1.exe (e.g. http://www.mediafire.com/?7d6guqfeqip1nhy) Setup_HxD.exe (e.g. http://mh-nexus.de/en/hxd/)
-
Hardware
flat-cable blue mark on same level side progskeet 1.1 subboard 360Clip-NAND
-
USB cable spring clamps (to press on clip) fine cutter cleaning brush wire (e.g. awg26) or IDE-cable or CAT5-cable soldering iron, solder
alcohol (isopropyl) cleaning compound
Auxiliary device
-
Set-up 360Clip-NAND (to rework)
-
Set-up Progskeet (solderbridge added on R9 and R11 to enable 3.3V and wire solder to subboard +3,3 and GND)
-
Set-up Progskeet (after cleaning contacts mounting flat-cable and spring clamp on NAND 0)
-
Set-up WingSkeet40000 (open WinSkeet40000, Common tab and go to the NAND tab)
Common tab NAND tab ( select NAND 1)
-
Set-up WingSkeet40000 (NAND 0)
click Auto check if manufact. on the NAND flash does correspond
click Dump and select file name for NAND 0
-
progress are normal slow , so if progress ist really fast, check conections or Common settings
Set-up WingSkeet40000 (NAND 0)
-
Set-up Progskeet (after cleaning contacts mounting flat-cable and spring clamp on NAND 1)
-
Set-up WingSkeet40000 (NAND 1)
click Auto check if manufact. on the NAND flash does correspond
click Dump and select file name for NAND 1
-
progress are normal slow , so if progress ist really fast, check conections or Common settings
Set-up WingSkeet40000 (NAND 1)
ProgSkeet Tutorial 360CLIPSet Up360Clip-NANDBitstream programmingsolderless NAND Foliennummer 4Foliennummer 5Foliennummer 6connecting the NAND clip(s) and dump NANDsHardwareAuxiliary deviceSet-up 360Clip-NAND(to rework)Set-up Progskeet(solderbridge added on R9 and R11 to enable 3.3V and wire solder to subboard +3,3 and GND)Set-up Progskeet(after cleaning contacts mounting flat-cable and spring clamp on NAND 0)Set-up WingSkeet40000(open WinSkeet40000, Common tab and go to the NAND tab)Set-up WingSkeet40000(NAND 0)Set-up WingSkeet40000(NAND 0)Set-up Progskeet(after cleaning contacts mounting flat-cable and spring clamp on NAND 1)Set-up WingSkeet40000(NAND 1)Set-up WingSkeet40000(NAND 1)