plug cementing nl 08 sep 99-a
DESCRIPTION
Plug Cementing of an Oil Well Cement jobTRANSCRIPT
PLUG CEMENTING
Module CF110 NL08 Sep 99
2
ObjectivesBy the end of this module, a trainee will be able to do the followings: List the purpose of setting a cement plugs List the three different techniques List the advantages and disadvantages of each technique Recognise the job consideration Select slurry properties to fit with the plug type Explain step by step the cement plug job procedure All necessary calculations to perform a balanced plug
3
Cement Plugs Introduction Setting a cement plug in a well is a
common oil-field operation.
A cement plug involves a relatively small volume of cement slurry.
And is placed in the wellbore for various purposes:
To side track above a fish or to initiate directional drilling.
To plug back a zone or plug back a well.
To solve a lost-circulation problem during the drilling phase,
To provide an anchor for OH tests.
4
Side Track and Directional Drilling
Kick Off Point
NEW
HOLE
CEMENT PLUG
5
Plug Back and Depleted Zone
Depleted Zone
Cement Plug
6
Lost Circulation
Drill Pipe
Open Hole
Drill Pipe
Thief ZoneCEMENT
PLUGCEMENT
PLUG
7
Abandonment
CEMENT PLUG
CEMENT PLUG
CEMENT PLUG
10
Plug Placement TechniquesThere are three common techniques for placing cement plugs:
Balanced plug
Dump bailer
Two-plug method
11
Balanced Plug
Displ. Fluid
Spacer
Cement Slurry
Balancing
12
Balanced Plug
Displ. Fluid
Spacer
Cement Slurry
Plug Length
Balancing Reversing
13
Dump Bailer Method
WIRELINE
DUMP BAILER
CEMENT SLURRY
ELECTRICAL/ MECHANICAL DUMP RELEASE
BRIDGE PLUGCASING
14
Dump Bailer MethodAdvantages:
Depth of cement plug is easily controlled.
Relatively cheap.
Disadvantages:
Not easily adaptable to setting deep plugs.
Quantity of cement limited to volume of dump bailer.
17
Coiled Tubing Cement Plug Technique
Cement
Suspended mud System
Coiled Tubing
18
Job Design Considerations Why is the cement plug being set? At what depth will the plug be set? Across which formations is the plug going to be
set? At what density should the slurry be mixed? What is the BHT? What volume should be pumped? What is the required thickening time? How to insure the cement will not be
contaminated by mud? Are pipe centralization and rotation necessary? Waiting on cement time?
19
Slurry PropertiesDensity - lighter for Lost CirculationDensity - heavier for SidetrackingDensity - homogeneous - batch mixingRheology - higher for Lost CirculationRheology - lower for placement with Coiled TubingCompressive Strength - higher for SidetrackingCompressive Strength - less important for Lost Circulation
Compressvie Strength - minimum 500 psi for drill outThickening Time - enough for placement - 1.5 to 2 hours
22
Reasons for Cement Plug Failures
Lack of hardness (sidetracking).
Poor isolation (plugback, abandonment).
Wrong Depth (all plugs).
Not in place due to sinking to the bottom (all plugs).
Not in place due to loss to thief zone (lost circulation).
23
Reasons for Failure Can be Traced to the
Following Slurry not designed for enough compressive strength.
Not enough WOC time.
Inaccurate BHST.
Cement contamination during displacement and POH.
Slurry not designed for the specific problem (lost circulation).
Not enough cement volume.
Difference between cement and hole fluids' densities too high, causing the plug to sink.
24
Plug Cementing - ConclusionsPlace the plug in a competent formation (i.e., a hard
formation).Use ample cement.Use a tailpipe through plugback intervals.Use centralizers on the tailpipe where the hole is not excessively washed out.
Use a drill pipe plug and a plug catcher.Condition the well before running the job, using low YP and PV mud, but of sufficient weight to control the well.
Ahead of the cement, run a high-vis pill that is compatible with the mud and will prevent the cement from sliding down the hole.
Use spacers and washes to combat the effects of mud contamination. Densified cements with a dispersant are also useful.
Allow ample time for the cement to set.
25
Diverter Tool
8 holes phased at 450
Bull Plug
26
Drill Pipe Centralization & Diverter Tool
DRILLPIPECENTRALIZED
9.0 lb/gal MUD
9.0 lb/gal MUD
SPACER
16.0 lb/gal CEMENT
DIVERTER TOOL
9.1 lb/gal VISCOUS BENTONITE PILL
27
Bad Cement Placement Technique
9.0 lb/gal MUD
9.0 lb/gal MUD
SPACER
13.8lb/gal 15.8 lb/gal17.5 lb/galCEMENTBENTONITE PILL
28
Reverse Circulating Excess Cement
H
L
29
Job Procedure - Balanced Plug Test treating lines.
Pump spacer or wash ahead of cement slurry. Mix and pump cement slurry. Pump spacer or wash behind cement slurry. Displace calculated amount of displacing fluid. Under displace 1/2-1 bbl for safety.
Open return lines to the displacement tank on the unit and allow plug to balance itself either by return flow or vacuum.
Pull drill pipe or tubing above the plug. Reverse circulate if conditions allow. POOH and WOC.
30
Slurry Volume Calculation
7000
7500
Desired Plug At End of Displacement
Mud
Spacer Cement
Drillpipe/tubing
Lsp2
Lcmt
L
31
Slurry Volume Calculation
Volume of Cement, Vcmt
Vcmt = L x Ch x excess factor
where,
L = length of column of cement in open hole
(ft).
Ch = capacity of open hole from standard tables
(ft3/ft).
32
Slurry Volume Calculation
Volume of Cement, VcmtVcmt = L x Ch x excess factor, where,L = length of column of cement in open hole (ft).Ch = capacity of open hole from standard tables (ft3/ft).
Length of Balanced Plug (with working string in place).
where,
Can = Capacity of annulus between tubing or drill pipe and open hole(ft3ft).
Ctbg = Capacity of tubing or drill pipe (ft3/ft).
Lcmt = Vcmt
Can + Ctbg
33
Slurry Volume Calculation
Volume of Spacer Behind the Cement
Vsp1 = Volume of spacer ahead of the cement
Vsp2 = Vsp
1Can
x C tbg
34
Slurry Volume Calculation
Volume of Spacer Behind the Cement
Vsp1 = Volume of spacer ahead of the cement
Length of Spacer
Vsp2 = Vsp
1
Can x C tbg
Lsp2 = length of spacer behind (ft) = Vsp2 / Ctbg
35
Slurry Volume Calculation Volume of Spacer Behind the Cement
Vsp1 = Volume of spacer ahead of the cement
Length of Spacer
Displacement Volume
D = depth of work string (bottom of cement plug) (ft)
VVd = Ctbg x [D - (Lcmt + Lsp2)]
V sp2 = V sp
1
C an x C tbg
Lsp2 = length of spacer behind (ft) = V sp2 / Ctbg