PC102: CLOUDY WATERSMART START Pool School

WHAT CAUSES CLOUDY WATER?

➤ Cloudy water is the most common pool problem pool owners face every year.

➤ There are multiple causes of cloudy water, and they can occur at the same time:

➤ Inadequate circulation

➤ Inadequate filtration

➤ Lack of sanitizer

➤ Not shocking frequently enough

➤ Improper water balance

CLOUDY V. HAZY

➤ Pools can experience varying degrees of cloudiness, depending on what is causing the problem. We use two terms to define water clarity.

➤ Hazy: the bottom is visible, but not clearly.

➤ Cloudy: the bottom is not visible.

➤ It is important to distinguish how cloudy your pool is, as recommendations will differ to fix the issue.

CIRCULATION & FILTRATION

➤ Inadequate circulation—usually, not enough circulation—means that not enough water is getting through the filter.

➤ The amount of circulation required is calculated in turnovers, or the amount of time it takes to move an amount of water through the system equal to the pool’s total gallonage. However, this does not mean all the water has been circulated and filtered!

➤ After 5-6 hours of operation, most pools have only circulated roughly 42% of the total volume; after 10-12 hours, approximately 84% of the volume has been filtered. At 24 hours, 98% of water has been filtered.

➤ Pool owners should run their pump, at minimum, 10-12 hours a day (24 hours is preferable) in the heat of the day to get the best circulation.

➤ Additionally, the pool should be left uncovered for at least 24 hours over the course of the week; covered pools have nowhere to release the gases produced by the pool, leaving those gases to be reabsorbed into the pool and cause clarity issues as well as other problems.

CIRCULATION AND FILTRATION

➤ The filter needs to be in good working order, with fresh media that is regularly cleaned.

➤ Sand that is older than 5 years or cartridge filters older than 2 years should be replaced.

➤ Sand should be backwashed and cartridge filters cleaned when pressure increases 8-10psi above “clean pressure,” or the pressure at which the filter reads after being freshly cleaned or installed.

➤ Every six weeks (twice a year minimum), the filter(s) should be chemically cleaned to remove oils, greases, and other material that regular water will not remove.

SANITATION & SHOCK

➤ Low sanitizer levels and not shocking enough can result in a buildup of contaminants, making sanitizer less effective.

➤ Always maintain sanitizer levels in the recommended range, preferably at the top of the range.

➤ Shock weekly, even if the pool has not been used; additionally, apply shock after rainfall, heavy use, and large water replacements.

WATER BALANCE

➤ Multiple parameters can contribute to cloudy water:

➤ High pH on its own will cause dissolved materials to come out of solution, making the water appear cloudy. High pH will also make sanitizer and shock less effective, keeping water cloudy longer.

➤ High total hardness (calcium hardness) can result in calcium falling out of solution, clouding the water.

➤ Excessively high total dissolved solids (TDS) can reduce how effective chemicals are when added, meaning treatment of cloudy water takes longer.

➤ The use of off-brand chemicals or non-pool-grade chemicals can result in unwanted additives entering the pool; in large quantities, these can cause clouding, especially when added dry to the pool.

TREATING HAZY WATER

➤ Ensure the pump is running 24 hours a day and the filter is fresh and has been recently chemically cleaned.

➤ Check the water balance and adjust out-of-range parameters; for high calcium, apply Scale Inhibitor to pull calcium back into solution.

➤ Shock the pool if it has not been shocked in the last 48 hours. Sometimes shock is enough to clear the pool. Be sure to leave the pool uncovered for 8 hours after applying shock.

➤ If shock does not help, a clarifier like Polysheen Blue or Natural Clarifier can be used.

➤ Pay close attention to the dosing on Polysheen Blue; do not overdose! Excessive clarifier can make a hazy pool worse!

➤ If cleaning up after algae, Pool First Aid is a good choice to consume dead algae along with binding up small particles.

TREATING CLOUDY WATER

➤ Ensure the pump is running 24 hours a day and the filter is fresh and has been recently chemically cleaned.

➤ Check the water balance and adjust out-of-range parameters; for high calcium, add fresh water to reduce calcium levels or Scale Inhibitor to pull calcium back into solution.

➤ Shock the pool if it has not been shocked in the last 48 hours. Be sure to leave the pool uncovered for at least 8 hours after applying shock.

➤ For particularly opaque pools, a floccing agent like PowerFloc can help to settle material to the bottom of the pool to be vacuumed.

➤ PowerFloc cannot be used on pools that do not have an option to vacuum to waste!

➤ A filter aid like Pool Tonic or Softswim Filter Aid can help to push as much material into the filter as possible. Pay close attention to filter pressure when using these products, as it will rise very quickly.

WHAT ABOUT…?

➤ Muriatic acid: this can be used to balance the pH to the recommended range, but continual use of acid to try to clear a cloudy pool can result in equipment corrosion and bather discomfort if the pH is too low. Check pH first before adding muriatic acid.

➤ Stabilizer: excessive stabilizer is not a known contributor to cloudy water. If stabilizer falls out of solution, it can be vacuumed.

➤ Bleach: Also known as liquid chlorine, this is a very weak shock that dissipates very quickly in the pool. Most liquid chlorine contains fillers that can take time to leave the pool. In general, there are better options for shock treatments.

THANK YOU!Click NEXT to continue!