parameter attribute mapping for migrating btsplus to the flexi bsc product family

Nokia Siemens Networks GSM/EDGE BSS, rel. RG10(BSS), operating documentation, issue 04

Reference

Parameter/attribute mapping for migrating BTSplus to theFlexi BSC product family

DN0933393

2DN0933393

Parameter/attribute mapping for migrating BTSplus tothe

Id:0900d805806218e3

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2009. All rights reserved

f Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment. Some of the parts may also have elevated operating temperatures.

Non-observance of these conditions and the safety instructions can result in personal injury or in property damage.

Therefore, only trained and qualified personnel may install and maintain the system.

The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards.

The same text in German:

Wichtiger Hinweis zur Produktsicherheit

In elektrischen Anlagen stehen zwangsläufig bestimmte Teile der Geräte unter Span-nung. Einige Teile können auch eine hohe Betriebstemperatur aufweisen.

Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Körperverlet-zungen und Sachschäden führen.

Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet.

Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Geräte müssen die zutreffenden Sicherheitsbestimmungen erfüllen.

DN0933393 3

Parameter/attribute mapping for migrating BTSplus to the

Id:0900d805806218e3

Table of ContentsThis document has 178 pages.

Summary of changes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.1 Abis mediation of BTSplus parameters towards Flexi BSC. . . . . . . . . . 13

2 ControlFile format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142.1 Common info (not class-specific) for the migration procedure. . . . . . . . 142.2 BTSM selection and migration (BCF and O&M LAPD creation) . . . . . . 142.3 TRX selection and migration (LAPD creation only) . . . . . . . . . . . . . . . . 15

3 Create LAPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.1 abisSigChannelSubSlot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.2 abisSigChannelTimeSlotPcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183.3 abisSigChannelTimeSlotTsl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.4 adminState. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.5 bitRate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.6 Id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.7 name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.8 parentBSCId . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213.9 relatedLapdLinkName . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223.10 sapi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223.11 tei . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4 Create BCF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234.1 T200F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234.2 T200S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234.3 adminState. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.4 batteryBackupProcedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.5 bcchTrxBatbuTimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254.6 bcfType . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254.7 lapdLinkName . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264.8 normTrxBatbuTimer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264.9 normTrxBatbuTimer2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274.10 normTrxBatbuTimer3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5 Create BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285.1 Migration of BR product line complex cells . . . . . . . . . . . . . . . . . . . . . . 285.1.1 Example for standard cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295.1.2 Example for dual band standard cell . . . . . . . . . . . . . . . . . . . . . . . . . . . 305.2 Packet migration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325.2.1 Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335.3 Frequency hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335.4 acDIMinCiRatioEst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355.5 adaptiveLaAlgorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355.6 adminState. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355.7 amrHoFrInHoThrDlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365.8 amrHoFrThrDlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4DN0933393


Id:0900d805806218e3

5.9 amrHoFrThrUlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375.10 amrHoHrInHoThrDlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375.11 amrHoHrThrDlRxQual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385.12 amrHoHrThrUlRxQual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385.13 amrPocFrPcLThrDlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395.14 amrPocFrPcLThrUlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395.15 amrPocFrPcUThrDlRxQual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405.16 amrPocFrPcUThrUlRxQual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405.17 amrPocHrPcLThrDlRxQual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415.18 amrPocHrPcLThrUlRxQual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415.19 amrPocHrPcUThrDlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425.20 amrPocHrPcUThrUlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425.21 antennaHopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435.22 bcchGSM900Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435.23 bsIdentityCodeBCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435.24 bsIdentityCodeNCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445.25 cellId . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445.26 cellNumberInBtsHW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455.27 directGPRSAccessBts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455.28 egprsInitMcsAckMode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465.29 egprsInitMcsUnAckMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465.30 egprsLinkAdaptEnabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475.31 egprsMaxBlerAckMode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475.32 egprsMaxBlerUnAckMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485.33 egprsMeanBepOffset8psk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485.34 egprsMeanBepOffsetGmsk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495.35 frequencyBandInUse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495.36 gprsEnabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505.37 gprsMsTxPwrMaxCCH1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505.38 gprsMsTxpwrMaxCCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515.39 gprsNonBCCHRxlevLower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515.40 gprsNonBCCHRxlevUpper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525.41 gprsRxlevAccessMin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525.42 hcsPriorityClass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535.43 hcsThreshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535.44 hoppingMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545.45 hoppingSequenceNumber1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545.46 hoppingSequenceNumber2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555.47 hoppingSequenceNumber3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555.48 inactEndTimeHour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565.49 inactEndTimeMinute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565.50 inactStartTimeHour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575.51 inactStartTimeMinute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575.52 inactWeekDays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585.53 csAckDl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585.54 csAckUl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595.55 csExtAckDl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

DN0933393 5


Id:0900d805806218e3

5.56 csExtAckUl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605.57 csExtUnackDl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605.58 csExtUnackUl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615.59 csUnackDl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615.60 csUnackUl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625.61 initMcsExtAckMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625.62 initMcsExtUnackMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 635.63 interferenceAveragingProcessAverPeriod. . . . . . . . . . . . . . . . . . . . . . . 635.64 interferenceAveragingProcessBoundary0 . . . . . . . . . . . . . . . . . . . . . . . 645.65 interferenceAveragingProcessBoundary1 . . . . . . . . . . . . . . . . . . . . . . . 645.66 interferenceAveragingProcessBoundary2 . . . . . . . . . . . . . . . . . . . . . . . 645.67 interferenceAveragingProcessBoundary3 . . . . . . . . . . . . . . . . . . . . . . . 655.68 interferenceAveragingProcessBoundary4 . . . . . . . . . . . . . . . . . . . . . . . 655.69 interferenceAveragingProcessBoundary5 . . . . . . . . . . . . . . . . . . . . . . . 655.70 locationAreaIdLAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 665.71 locationAreaIdMCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 665.72 locationAreaIdMNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675.73 maxNumberOfRepetition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675.74 msMaxDistInCallSetup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685.75 msTxPwrMaxCCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685.76 msTxPwrMaxCCH1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695.77 msTxPwrMaxGSM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695.78 msTxPwrMaxGSM1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705.79 noOfMFramesBetweenPaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705.80 nbrOfSlotsSpreadTrans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715.81 noOfBlocksForAccessGrant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715.82 nonBCCHLayerOffset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725.83 pcuCsHopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725.84 pcuCsNonHopping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 735.85 pcuDlBlerCpHopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 735.86 pcuDlBlerCpNonHop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745.87 pcuDlLaRiskLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745.88 pcuUlBlerCpHopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 755.89 pcuUlBlerCpNonHop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 755.90 pcuUlLaRiskLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 765.91 qSearchP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 765.92 raReselectHysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775.93 rac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775.94 radiusExtension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 785.95 segmentId . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 785.96 segmentName . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 795.97 superRadiusExtension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 795.98 throughputFactor_cs1cs4dlcs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 805.99 throughputFactor_cs1cs4ulcs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 805.100 throughputFactor_mcs1mcs4ulcs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 815.101 throughputFactor_mcs1mcs9dlcs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 815.102 throughputFactor_mcs1mcs9ulcs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

6DN0933393


Id:0900d805806218e3

6 Create TRX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 836.1 bbUnitSupportsEdge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 846.2 channel0Maio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 856.3 channel0Pcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 856.4 channel0Subslot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 866.5 channel0Tsl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 866.6 channel0Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 876.7 channel1Maio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 876.8 channel1Pcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 886.9 channel1Subslot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 886.10 channel1Tsl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896.11 channel1Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896.12 channel2Maio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 906.13 channel2Pcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 906.14 channel2Subslot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 916.15 channel2Tsl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 916.16 channel2Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 926.17 channel3Maio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 926.18 channel3Pcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 936.19 channel3Subslot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 936.20 channel3Tsl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 946.21 channel3Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 946.22 channel4Maio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 956.23 channel4Pcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 956.24 channel4Subslot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 966.25 channel4Tsl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 966.26 channel4Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 976.27 channel5Maio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 976.28 channel5Pcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 986.29 channel5Subslot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 986.30 channel5Tsl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 996.31 channel5Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 996.32 channel6Maio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006.33 channel6Pcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006.34 channel6Subslot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1016.35 channel6Tsl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1016.36 channel6Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1026.37 channel7Maio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1026.38 channel7Pcm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1036.39 channel7Subslot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1036.40 channel7Tsl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1046.41 channel7Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1046.42 circuitTelecom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1056.43 eTrxInd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1056.44 initialFrequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1066.45 lapdLinkName . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1066.46 trxFrequencyType . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

DN0933393 7


Id:0900d805806218e3

6.47 tsc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

7 Create MAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1087.1 frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1087.2 frequencyBandInUse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

8 Create BAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1108.1 frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1108.2 frequencyBandInUse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

9 Create POC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1129.1 alpha . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1129.2 bepPeriod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1129.3 bsTxPwrMax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1139.4 bsTxPwrMax1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149.5 bsTxPwrMin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149.6 bsTxPwrOffset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1159.7 enableAla. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1159.8 minIntBetweenAla . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1169.9 pcALDlWeighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1169.10 pcALDlWindowSize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1179.11 pcALUlWeighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1179.12 pcALUlWindowSize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189.13 pcAQLDlWeighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189.14 pcAQLDlWindowSize. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1199.15 pcAQLUlWeighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1199.16 pcAQLUlWindowSize. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1209.17 pcControlInterval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1209.18 pcIncrStepSize. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1219.19 pcLTQual144RxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1219.20 pcLTQualDlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1229.21 pcLTQualUlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1239.22 pcLowerThresholdsLevDLRxLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . 1239.23 pcLowerThresholsLevULRxLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1249.24 pcRedStepSize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1249.25 pcUTQualDlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1259.26 pcUTQualUlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1269.27 pcUpperThresholdsLevDLRxLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . 1269.28 pcUpperThresholdsLevULRxLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . 1279.29 pcControlEnabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1279.30 powerDecrQualFactor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

10 Create HOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12910.1 amhTrhoPbgtMargin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12910.2 averagingWindowSizeAdjCell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12910.3 ddeThresholdsLevRxLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13010.4 enaFastAveHo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13110.5 enableIntraHoDl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13110.6 enableIntraHoUl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

8DN0933393


Id:0900d805806218e3

10.7 enableMsDistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13210.8 enablePowerBudgetHo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13310.9 enableSddchHandover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13310.10 enableUmbrellaHo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13410.11 hoAvaragingLevDLWeighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13410.12 hoAvaragingLevDlWindowSize. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13510.13 hoAveragingLevUlWeighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13510.14 hoAveragingLevUlWindowSize. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13610.15 hoAveragingQualDlWeighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13610.16 hoAveragingQualDlWindowSize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13710.17 hoAveragingQualUlWeighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13710.18 hoAveragingQualUlWindowSize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13810.19 hoPeriodPbgt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13810.20 hoTLDlPx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13910.21 hoTLDlRxLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13910.22 hoTLUlNx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14010.23 hoTLUlPx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14010.24 hoTLUlRxLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14110.25 hoTQDlNx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14110.26 hoTQDlPx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14210.27 hoTQDlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14210.28 hoTQUlNx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14310.29 hoTQUlPx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14310.30 hoTQUlRxQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14410.31 hoThresholdsInterferenceDlRxLevel. . . . . . . . . . . . . . . . . . . . . . . . . . . 14410.32 hoThresholdsInterferenceULRxLevel . . . . . . . . . . . . . . . . . . . . . . . . . . 14510.33 hoThresholdsLevDLNx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14510.34 intraHoLoRxLevLimAmrHr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14610.35 maxMsDistanceHoThreshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14610.36 minIntBetweenHoReq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14710.37 minIntBetweenUnsuccHoAttempt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14710.38 minIntUnsuccIsHo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14810.39 minMsDistanceHoThreshold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14810.40 modifiedAveWinNCell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14910.41 msDistanceAveragingParamHreqave. . . . . . . . . . . . . . . . . . . . . . . . . . 14910.42 msDistHoParamMsRngMax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15010.43 msSpeedDetectionState . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15010.44 smaxMsDistanceHoThreshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15110.45 sminMsDistanceHoThreshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15110.46 superReuseBadCiThresholdCiRatio . . . . . . . . . . . . . . . . . . . . . . . . . . . 15210.47 superReuseBadRxLevThresholdRxLevel . . . . . . . . . . . . . . . . . . . . . . . 15210.48 superReuseGoodCiThresholdCiRatio. . . . . . . . . . . . . . . . . . . . . . . . . . 15310.49 superReuseGoodRxLevThresholdRxLevel. . . . . . . . . . . . . . . . . . . . . . 15310.50 interSystemDa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15410.51 intraHoUpRxLevLimAmrHr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15410.52 msSpeedThresholdNx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15510.53 msSpeedThresholdPx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

DN0933393 9


Id:0900d805806218e3

11 Create ADCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15611.1 adjCellBsicBcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15611.2 adjCellBsicNcc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15711.3 adjacentCellIdCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15711.4 adjacentCellIdLac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15711.5 adjacentCellIdMCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15811.6 adjacentCellIdMNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15811.7 bcchFrequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15911.8 chainedAdjacentCell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15911.9 dtmPowerBudgetMargin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16011.10 enableHoMarginLevQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16011.11 fastMovingThreshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16111.12 gprsEnabled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16111.13 gprsMsTxPwrMaxCCH1x00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16211.14 gprsMsTxpwrMaxCCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16211.15 gprsPenaltyTime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16311.16 gprsRxlevAccessMin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16311.17 gprsTemporaryOffset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16411.18 hcsPriorityClass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16411.19 hcsThreshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16511.20 hoMarginLev . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16511.21 hoMarginPbgt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16511.22 hoMarginQual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16611.23 hoPriorityLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16611.24 msTxPwrMaxGSM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16611.25 msTxPwrMaxGSM1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16711.26 nccrEgprsPbgtMargin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16711.27 nccrEgprsQualityMargin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16811.28 nccrGprsPbgtMargin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16811.29 nccrGprsQualityMargin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16911.30 rac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16911.31 levelAdj . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17011.32 reportingPriority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17011.33 rxLevMinCell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17111.34 trhoTargetLevel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

12 Create ADJW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17212.1 AdjwCId . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17212.2 cellParameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17212.3 fddReportingPriority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17312.4 isnccrFddQualityThr. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17312.5 lac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17412.6 mcc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17412.7 minEcnoThreshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17512.8 mnc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17512.9 rncId. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17612.10 scramblingCode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17612.11 syncCase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177

10DN0933393


Id:0900d805806218e3

12.12 txDiversityInd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17712.13 uarfcn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

DN0933393 11


Id:0900d805806218e3

List of TablesTable 1 Mapping for BR [CHAN] CHTYPE to channel<n>Type . . . . . . . . . . . . 84

12DN0933393


Id:0900d80580621ad2

Summary of changes

Summary of changesChanges between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.

Issue 01 for release RG10(BSS)

Issue Date Summary

01 10/2009 First issue for RG10(BSS)

DN0933393 13


Introduction

Id:0900d8058063e1ac

1 IntroductionThis document considers in detail all the configuration parameters in the BSS managed object hierarchy that need to be configured for operating the BTSplus with the Flexi BSC product family.

When migrating a BTSplus base station to the Flexi BSC product family, a related “BCF” managed object instance needs to be created in the Flexi BSC configuration plan. The underlying hierarchy of the BCF managed object (such as the “BTS”, “TRX” and “POC” managed objects) also needs to be created. The new BTSplus base station type is rep-resented by the value 7 being assigned to the “site type (TYPE)” parameter.

The BTSplus is migrated using the exporter offline migration tool. In particular, this tool automatically creates all the BSS managed objects necessary for operating the BTSplus with the Flexi BSC product family. It maps BTSplus-related configuration parameters from the BR info model to the equivalent parameters in the BSS managed object hierarchy. Parameters that are required by the Flexi BSC, but that cannot be found in the eBSC/BSC1 configuration plan, are provided by means of a control file that is manually edited by the user during the migration process and used as input to the exporter tool.

Management of the BTSplus base station site type by the Flexi BSC product family is also supported by a number of new parameters in the BSS managed object hierarchy. For example, a new BCF parameter “BTS site subtype (-)” distinguishes between the three different types of BTSplus base station site: basic, mainline and eMicro.

The migration of the BTSplus to a Flexi BSC requires an OAM network that is already operational, including NetAct and the Flexi BSC. It is possible to have other BTS types (for example the Flexi EDGE BTS) being managed by the same Flexi BSC together with the BTSplus. For more information on the BTSplus migration procedures and the exporter migration tool, refer to the “Migrating BTSplus to the Flexi BSC product family” functional area description. For a description of the control file, refer to “Control File format”.

For an overall description of operating the BTSplus with the Flexi BSC product family, refer to the “BSS21469: BSxx@Flexi BSC product family” feature description.

1.1 Abis mediation of BTSplus parameters towards Flexi BSCBesides the migration of BTSplus-related configuration parameters to the BSS managed object hierarchy, as described in “Introduction”, the parameters and attributes required by the BTSplus for its operation also need to be translated in real time from BR format to Flexi BSC format and vice versa. This translation is done by an Abis interface mediation function on the BTSplus. A detailed description of this mediation can be found in “Abis mediation of BTSplus parameters/attributes towards the Flexi BSC product family”.

Furthermore, a listing of the BTSplus-related parameters and attributes in BR format can be found in the respective command manuals: • “BTSplus basic commands at Flexi BSC product family” • “BTSplus mainline commands at Flexi BSC product family” • “BTSplus eMicro commands at Flexi BSC product family”

14DN0933393


Id:0900d805806218b8

ControlFile format

2 ControlFile formatWhen using the exporter migration tool to automatically rehost BTSplus base stations from an eBSC/BSC1 to the Flexi BSC product family, you need to provide additional information to assist the migration process. For example, you need to specify which BTSM objects need to be migrated, and which ID they will be assigned. For this purpose, an XML-based control file is used as input for the exporter tool, together with the eBSC/BSC1 configuration file.

For more information, refer to “Data export and migration” in the “Migrating BTSplus to the Flexi BSC product family” functional area description.

2.1 Common info (not class-specific) for the migration proce-dure

2.2 BTSM selection and migration (BCF and O&M LAPD cre-ation)

<commonData>

… name attribute of the cmData tag in the resulting script; takes the value of NAME<bscid>, where bscid is the value given by the --bscid input parameter to the exporter migration tool

… id attribute of the cmData tag in the resulting script; takes the value of ID<bscid>, where bscid is as described above

… identifier of the target BSC; takes the value of <bscid>, where bscid is as described above

… distinguishing name of the target BSC; takes the value of PLMN-PLMN/BSC-<bscid>, where bscid is as described above

</commonData>

<sourceObject mmlName=“…” BTSM to be migrated

… BCF-level part of distName of the created BCF; takes the value of BCF-<btsmn>, where btsmn is the source BTSM index

… name given to the OAM LAPD link of the BCF and used as the lapdLinkName param-eter of the created BCF and as the name parameter of the related OAM LAPD; takes the value of L<lapdn>, where lapdn is a unique index of LAPDs being migrated and starts from 1, unless otherwise specified by the --first_lapd input parameter to the exporter tool

DN0933393 15


ControlFile format

Id:0900d805806218b8

2.3 TRX selection and migration (LAPD creation only)

… LAPD-level part of the distName of the created OAM LAPD; takes the value of LAPD-<lapdn>, where lapdn is as described above

… the PCM in the new configuration to be asso-ciated with the existing PCM specified in PCMCON0; takes the value of <pcmbn>, where pcmbn is the source PCMB index, and is possibly added to the value specified by the --first_pcmb input parameter to the exporter tool

… the PCM in the new configuration to be asso-ciated with the existing PCM specified in PCMCON1







</sourceObject>

<sourceObject mmlName=“…”> TRX to be migrated

… lapdLinkName of the created TRX and name of the related radio signaling LAPD; takes the value of L<lapdn>, where lapdn is a unique index of LAPDs being migrated and starts from 1, unless otherwise speci-fied by the --first_lapd input parameter to the exporter migration tool

16DN0933393


Id:0900d805806218b8

ControlFile format

… LAPD-level part of distName of created sig-naling LAPD; takes the value of LAPD-<lapdn>, where lapdn is as described above

… TEI of LAPD; takes the value of <trxn>, where trxn is as described above

</sourceObject>

DN0933393 17


Create LAPD

Id:0900d8058063d161

3 Create LAPD

The CREATE LAPD instances are derived as :

• One OAM LAPD for the related BCF (derived from the first LPDLM configured on the BTSplus PORT_0)

• NUM_TRX: one radio signaling link LAPD created for each TRX subordinated to the related BCF

g The BR LAPD allocation on the PCM line (the related timeslot number) is not changed in the migrated configuration

3.1 abisSigChannelSubSlot

Create LAPD Example from Real NetAct Configuration script managedObject class="LAPD" operation="create" version="S14.1">

1 133 30 2 32 0 85703 T45 EXS12 0 2

/managedObject>

Obj LAPD M,O,N,internal mapped Val

Full Name Sub TSL Type Number Range 0...7, step 1 Internal Value gui_value Default Description SubTimeslot of the PCM where the LAPD will be created. BitRate 8 kBit/s, Sub TSL = 0..7. BitRate 16 kBit/s, Sub

TSL = 0,2,4,6. BitRate 32 kBit/s, Sub TSL = 0,2,4. BitRate 64 kBit/s, Sub TSL = Not Defined 3Gpp Multip 1 Modification Not modifiable Modified onCreate mandatory Val info derived from [LAPD] LPDLMN and from control file for PCM mapping (related BTSM sourceObject)

With 64 kBit/s abisSigChannelSubSlot must be skipped

18DN0933393


Id:0900d8058063d161

Create LAPD

3.2 abisSigChannelTimeSlotPcm

Obj LAPD M,O,N,internal mapped Val

Full Name PCM Type Number Range 0...3391, step 1 Internal Value gui_value Default Description PCM where the LAPD link has been created 3Gpp Mult ip 1 Modif ication Not modifiable Modif ied onCreate mandatory Val info derived from [LAPD] LPDLMN and from control file for

PCM mapping (related BTSM sourceObject)

DN0933393 19


Create LAPD

Id:0900d8058063d161

3.3 abisSigChannelTimeSlotTsl

3.4 adminState

Obj LAPD M,O,N,internal mapped Val Full Name TSL Type Number Range 1...31, step 1 Internal Value gui_value Default Description Timeslot of the PCM where the LAPD link has been created 3Gpp Mult ip 1 Modification Not modifiable Modified onCreate mandatory Val info derived from [LAPD] LPDLMN and from control file for

PCM mapping (related BTSM sourceObject)

Obj LAPD M,O,N,internal M Val Full Name Administrative State Type Enumeration Range Unlocked (1), Locked (3) Internal Value gui_value Default Description Administrative State of the object. Note that, when using file based

activation method in plan provisioning, LAPD will be always automatically unlocked after creation regardless of the planned value.

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 1

20DN0933393


Id:0900d8058063d161

Create LAPD

3.5 bitRate

3.6 IdNetAct does not define the final ID for the LAPD, but the BSC does. So NetAct only creates a temporary ID for the LAPD. This temporary ID is created automatically and does not need to be present as part of distName in the RAML file. During plan provision-ing to the Flexi BSC, the BSC will reserve the actual ID for the LAPD. That info will be provided to NetAct as a LAPD creation event.

3.7 name

Obj LAPD M,O,N,internal M Val gui_value Full Name Bit Rate Type Enumeration Range 8 kbit/s (8), 16 kbit/s (16), 32 kbit/s (32), 64 kbit/s (64) Internal Value Default Description LAPD Link Bit Rate 3Gpp Multip 1 Modification Not modifiable Modified onCreate mandatory Val • For the O&M LAPD: is derived from the BR [LPDLM]

ABISCH • For the TRX LAPD: set the same value

Obj LAPD M,O,N,internal M Val Full Name Name Type String Range 1...5 characters Internal Value gui_value Default Description NW Name and Name of LAPD object. Enter with capital letters. 3Gpp Mult ip 1 Modification Not modifiable Modified onCreate mandatory Val • For the O&M LAPD: “lapdLinkName" info in control file

(related BTSM sourceObject) • For the TRX LAPD: “lapdLinkName" info in control file

(related TRX sourceObject)

DN0933393 21


Create LAPD

Id:0900d8058063d161

3.8 parentBSCId

Obj LAPD M,O,N,internal Internal Val Full Name /* not visible to the Operator: it is assigned by NetAct Configurator

automatically */ Type Number Range Internal Value /* not visible to the Operator: it is assigned by NetAct Configurator

automatically */ Default Description /* not visible to the Operator: it is assigned by NetAct Configurator

automatically */ 3Gpp Multip Modification /* not visible to the Operator: it is assigned by NetAct Configurator

automatically */ Modified onCreate /* not visible to the Operator: it is assigned by NetAct Configurator

automatically */ Val For all LAPD (O&M and signalling): “bscId" info in control file

(common data)

22DN0933393


Id:0900d8058063d161

Create LAPD

3.9 relatedLapdLinkNameRelatedLapdLinkName is set only in special cases. Therefore, it is not considered for migration.

3.10 sapi

3.11 tei

Obj LAPD M,O,N,internal M Val Full Name SAPI Type Enumeration Range Signalling LAPD (0), AcPool LAPD (61), O&M LAPD (62) Internal Value gui_value Default Signalling LAPD (0) Description Service access point identif ier that corresponds to the LAPD Link

object. 3Gpp Mult ip 1 Modif ication Not modifiable Modif ied onCreate mandatory Val • For the O&M LAPD: 62

• For the TRX LAPD: 0

Obj LAPD M,O,N,internal M Val Full Name TEI Type Number Range 0...126, step 1 Internal Value gui_value Default 0 Description Terminal end point identifier TEI = 1 for O&M LAPD and for Signalling

LAPD it is the TRX ID. 3Gpp Mult ip 1 Modif ication Not modifiable Modif ied onCreate mandatory Val • For the O&M LAPD: 1

• For the TRX LAPD: assigned to “id” of the related TRX (derived as unique number within BTSM)

DN0933393 23


Create BCF

Id:0900d805805c2699

4 Create BCF

4.1 T200F

4.2 T200S

Create BCF Example from Real NetAct Configuration script managedObject class="BCF" operation="create" version="S14.1" distName="BSC-12345/BCF-45">

<defaults name="ESTemplate"/> ExampleSite 5 269367786 605064855 ExampleSite EXSOM 3

/managedObject>

Obj B CF M ,O,N,internal m apped Val Ful l Name FAC CH LAP Dm T200 Type N umber Range 200...1260 m s, step 20 m s Internal Value gui_value / 20 Default 0 m s Description The param eter determ ines a LA PDm T200 for supervision of the FACC H

m essage transfer from BTS to mobile. 3Gpp M ultip 1 M odification N ot m odifiable M odified onCreate optional Val

1. take 1st BTS of that specific B TS M 2. take fie ld facchTCHF from [BTS] T200 and act the m apping as

10 + [BTS] T200 (facchTC HF fie ld) / (255 / 53)

Obj BCF M,O,N,internal mapped Val Ful l Name SDCCH LAPDm T200 Type Number Range 200...1260 ms, step 20 ms Internal Value gui_value / 20 Default 0 ms Description The parameter determines a LAPDm T200 for supervision of the

SDCCH message transfer from BTS to mobile. 3Gpp Multip 1 Modification Not modifiable Modified onCreate optional Val 1. take 1s t BTS of that specific BTSM

2. take field sdcchSAPI0 from [BTS] T200 and act the mapping as 10 + [BTS] T200 (sdcchSAPI0 field) / (255 / 53)

24DN0933393


Id:0900d805805c2699

Create BCF

4.3 adminState

4.4 batteryBackupProcedure

Obj BCF M,O,N,internal M Val Full Name Administrative State Type Enumeration Range Unlocked (1), Locked (3) Internal Value gui_value Default Locked (3) Description Administrative State of the object in the NW after object creation or

modification. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 1

Obj BCF M,O,N,internal M Val Full Name BTS Battery Backup Procedure Type Enumeration Range All Alive (0), Transmission and BCCH Alive (1), Transmission

Alive (2) Internal Value gui_value Default All Alive (0) Description With this parameter you define what type of BTS battery

backup procedure is used. The procedure is executed when the mains power goes down at the BTS site and there is a battery backup unit.

DN0933393 25


Create BCF

Id:0900d805805c2699

4.5 bcchTrxBatbuTimer

4.6 bcfType

Obj BCF M,O,N,internal mapped Val Full Name BCCH TRX Shutdown Timer Type Number Range 0...600 min, step 1 min Internal Value gui_value * 6000 Default 0 min Description With this parameter you define the time period after which shutdown

group 0 TRXs are powered down. The time begins after the TRX Shutdown Timer1 has expired.

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val MIN (INT ([BTSM].EMT1(emergencyTimer1) / 2), 600) * 6000

Obj BCF M,O,N,internal M Val Full Name Site Type Type Enumeration Range Nokia 2nd Generation (0), Nokia Talk-family (1), Nokia PrimeSite (2), Nokia MetroSite (3), Nokia InSite (4), Nokia

UltraSite (5), Nokia Flexi EDGE (6) Internal Value gui_value Default Description Identifies the type of the BTS site. Modifiable when provisioning plan with CM Operations Manager or command line

interface and not having Use File Based Activation Method for S12 BSC -option selected in GSM Options. 3Gpp Multip 1 Modification Requires object locking Modified When BCF is locked. The OMU link of the BCF cannot be in working state when the BTS site type is modified to

Nokia UltraSite. onCreate mandatory Val 7

26DN0933393


Id:0900d805805c2699

Create BCF

4.7 lapdLinkName

4.8 normTrxBatbuTimer

Obj BCF M,O,N,internal M Val Ful l Name LAPD Link Name Type String Range 1...5 characters Internal Value gui_value Default Description LAPD link name of the BTS Site O&M Link 3Gpp Multip 1 Modification On-Line Modified onCreate mandatory Val “lapdLinkName” info in control file

Obj BCF M,O,N,internal mapped Val Full Name TRX Shutdown Timer Type Number Range 0...600 min, step 1 min Internal Value gui_value * 6000 Default 0 min Description With this parameter you define the time period after which shutdown group 1 TRXs are powered down. The time

begins after the TRX Shutdown Timer 2 has expired. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val normTrxBatbuTimer2 +50

DN0933393 27


Create BCF

Id:0900d805805c2699

4.9 normTrxBatbuTimer2

4.10 normTrxBatbuTimer3

O bj B CF M ,O ,N,in ternal m apped Val

Ful l Name TRX S hutdown T im er 2 Type Num ber Range 0...600 m in, step 1 m in Interna l Va lue gui_va lue * 6000 Default 0 m in Description W ith th is parameter you define the tim e period after which shutdown

group 2 TRXs are pow ered dow n. The time begins a fter the TRX S hutdown T imer 3 has expired.

3Gpp M ultip 1 M odi fication O n-L ine M odi fied onCreate optiona l Val M AX (50, M IN (IN T ([BTSM ]EM T2(em ergencyT im er2) / 2), 550)) *

6000

O b j BC F M ,O ,N ,in terna l m apped Va l

F ul l N ame T RX S hutdow n T im er 3 T ype Num ber Range 0 ...600 m in , s tep 1 m in In te rna l Va lue gu i_va lue De fau lt 0 m in Descr ip tion W i th th is pa ram e te r you de fine the tim e pe riod a fter wh ich shu tdow n

group 3 T R Xs a re powered down . Param ete r is va lid on ly when BTSBa tte ry Backup Procedure pa ram eter has va lue ¿T ransm ission and BC CH Al ive (1 )¿ o r ¿T ransmis sion A live (2)¿

3G pp M u ltip 1 M odi fica tion O n-L ine M odi fied onCreate op tional Va l no rmT rxBa tbuT im er2 -50

28DN0933393


Id:0900d80580646c17

Create BTS

5 Create BTS

5.1 Migration of BR product line complex cellsBesides standard cells, the BTSplus administered by the eBSC/BSC1 can also be used to create complex overlay cell structures. When migrating these cell structure types to the Flexi BSC, special considerations have to be taken into account.

The following cell types are considered: • Standard cells • Extended cells • Concentric cells • Dual band standard cells

Standard cellsThe most common situation during migration is the direct mapping of a standard BTSplus cell to a standard cell managed by the Flexi BSC. This mapping is done auto-matically by the exporter migration tool. Refer to “Example for standard cell” for an example of a migrated standard cell.

Extended cellsExtended cells managed by the eBSC/BSC1 are not migrated to the Flexi BSC. Refer to “Extended cells” for more information.

Concentric cellsWhen administering the BTSplus with the Flexi BSC product family, concentric cells are managed as standard cells if they are not dual band. If the TRX of the INNER and COMPLETE area belong to different frequency bands, the cells are managed as dual band standard cells. Therefore, a pair of Flexi BSC cells is generated from the original cell. Refer to “Concentric cells” for more information.

Create BTS Example from Real NetAct Configuration script managedObject class="BTS" operation="create" version="S14.1" distName="BSC-12345/BCF-45/BTS-198">

<defaults name="ESTemplate"/> 57113 57113 5210 1 2 5 244 05 23 0 1 1 1 EXAMPLESITEG1 1 80 80 1

/managedObject>

DN0933393 29


Create BTS

Id:0900d80580646c17

Dual band standard cellsRefer to “Dual band cells” for more information on the migration of dual band standard cells. Refer to “Example for a dual band standard cell” for an example of a migrated dual band standard cell.

5.1.1 Example for standard cell

Migration steps:

1. Input (eBSC/BSC database text file)First of two inputs requested by the offline migration tool for migration of the standard cell:

2. Further mapping infoSecond of two inputs requested by the offline migration tool for migration of the standard cell:

NAME BTSM:2/BTS:2

BSIC 5-3 CELLGLID "555"-"01"-10183-10188

CELLTYP STDCELL BCCHFREQ 4

CALLF01=34, CALLF02=44, CALLF03=104

SYSID BB900 CONCELL FALSE

REQUESTED INFO SOURCE WHERE EXPECTED COMMENT <sourceObject mmlName="BTSM:2/BTS:2"> CONTROL FILE

(USED BY THE OFFLINE MIGRATION TOOL)

the values (i.e. the BTS numbering) are picked up from the free instances numbers available in the network to migrate

REQUESTED INFO SOURCE WHERE EXPECTED COMMENT BTS-198 CONTROL FILE



143 CONTROL FILE (USED BY THE OFFLINE MIGRATION TOOL)

The BSS segment

3000BRCN02 CONTROL FILE (USED BY THE OFFLINE MIGRATION TOOL)

example considering the agreed solution C

30DN0933393


Id:0900d80580646c17

Create BTS

3. Output:

5.1.2 Example for dual band standard cell

Migration steps:

1. Input (eBSC/BSC1 database text file)First of two inputs requested by the offline migration tool for migration of the standard cell:

INFO SOURCE WHERE EXPECTED COMMENT <managedObject class="BTS" version="S14" operation="create" distName="PLMN-PLMN/BSC-33333/BCF-222/BTS-198">

NetACt script (common RAML format)

143 NetACt script ( (common RAML format) 3000BRCN02 NetACt script (common RAML format)

BTS ID Added by BSC3i assigned at creation

cellNumber (HMO id) Built by Mediation on the BTS side

derived from SegmentName

NAME BTSM:0/BTS:11

BSIC 5-3 CELLGLID "555"-"01"-10183-10182

CELLTYP DBSTDCELL BCCHFREQ 94

CALLF01=614, CALLF02=624, CALLF03=114, CALLF04=113, CALLF05=112

SYSID GSMDCS CONCELL FALSE

REQUESTED INFO SOURCE WHERE EXPECTED COMMENT <sourceObject mmlName="BTSM:0/BTS:11"> CONTROL FILE

DN0933393 31


Create BTS

Id:0900d80580646c17

2. Further mapping infoSecond of two inputs requested by the offline migration tool for migration of the standard cell:

3. Output:

If an eBSC/BSC1 BTS object has to be split into a pair of Flexi BSC BTS objects, all the segment level parameters (except the segmentId parameter) are allocated only for the first one. The complete list is grouped in the following table:

REQUESTED INFO SOURCE WHERE EXPECTED COMMENT BTS-199 BTS-200

CONTROL FILE (USED BY THE OFFLINE MIGRATION TOOL)

1) The first BTS of the new splitted pair (e.g. 199) is the BTS with the BCCH TRX band 2) and HOC/PWRC must be considered only associated to the 1st BTS of the pair.

145 CONTROL FILE (USED BY THE OFFLINE MIGRATION TOOL)

The BSS segment

3000BRCN02 CONTROL FILE (USED BY THE OFFLINE MIGRATION TOOL)

example considering the agreed solution C

INFO SOURCE WHERE EXPECTED COMMENT <managedObject class="BTS" version="S14" operation="create" distName="PLMN-PLMN/BSC-33333/BCF-222/BTS-199"> <managedObject class="BTS" version="S14" operation="create" distName="PLMN-PLMN/BSC-33333/BCF-222/BTS-200">

NetACt script (common RAML format)

145 NetACt script ( (common RAML format) 3000BRCN11 NetACt script (common RAML format)

BTS ID Added by BSC3i assigned at creation

cellNumber (HMO id) Built by Mediation on the BTS side

derived from SegmentName

32DN0933393


Id:0900d80580646c17

Create BTS

5.2 Packet migrationThe migration tool simply migrates the BTSM object to an equivalent BCF object, includ-ing the complete underlying hierarchy. This means that any kind of external required managed objects (e.g. PCM resources, “NSVC” or “NSE” objects) have to be consid-ered independently and must be previously equipped in the network managed by the Flexi BSC. The BTSplus product line configuration is heavily dependent on this. More-over, the PTPPKF object is not a BR Abis managed object, and the main key features are implemented in the eBSC.

The EDAP configuration on the Abis interface connecting the BTSplus with the Flexi BSC requires information that cannot be provided by the packet configuration as described in the eBSC/BSC1 configuration script. Furthermore, the allocation of packet resources could demand more capacity on the new Abis interface.

Therefore, the migration tool implements a best-effort strategy. TCH timeslots are always preferred to packet timeslots. This means that the tool first attempts to migrate all the voice channels and to allocate them on the PCM line of the BSS Abis. Remaining timeslots can then be used to manually add the EDAP configuration to the RAML script. For this purpose, the exporter tool provides an inline list of all the idle timeslots for each LAPD, as shown in the example below.

1 bsIdentityCodeBCC 16 hcsPriorityClass 31 noOfBlocksForAccessGrant

2 bsIdentityCodeNCC 17 hcsThreshold 32 noOfMFramesBetweenPaging

3 cellId 18 initMcsExtAckMode 33 pcuCsHopping

4 directGPRSAccessBts 19 initMcsExtUnackMode 34 pcuCsNonHopping

5 egprsInitMcsAckMode 20 interferenceAveragingProcessAverPeriod 35 pcuDlBlerCpHopping

6 egprsInitMcsUnAckMode 21 locationAreaIdLAC 36 pcuDlBlerCpNonHop

7 egprsLinkAdaptEnabled 22 locationAreaIdMCC 37 pcuDlLaRiskLevel

8 egprsMaxBlerAckMode 23 locationAreaIdMNC 38 pcuUlBlerCpHopping

9 egprsMaxBlerUnAckMode 24 maxNumberOfRepetition 39 pcuUlBlerCpNonHop

10 egprsMeanBepOffset8psk 25 msMaxDistInCallSetup 40 pcuUlLaRiskLevel

11 egprsMeanBepOffsetGmsk 26 msTxPwrMaxCCH 41 qSearchP

12 gprsEnabled 27 msTxPwrMaxCCH1x00 42 rac

13 gprsMsTxpwrMaxCCH 28 msTxPwrMaxGSM 43 raReselectHysteresis

14 gprsMsTxPwrMaxCCH1x00 29 msTxPwrMaxGSM1x00

15 gprsRxlevAccessMin 30 nbrOfSlotsSpreadTrans

DN0933393 33


Create BTS

Id:0900d80580646c17

In order to implement this strategy, the exporter tool first identifies the proper Abis PCM and LAPD primary positions and extracts the related equipped subslots. From this available pool of resources, it then starts to map each TRX, allocating two consecutive 64 kbit/s timeslots per TRX. In doing so, the LAPD timeslots used on the BR Abis are preserved. This means that some configurations can result in an LAPD timeslot breaking up a sequence of two consecutive 64 kbit/s timslots that could otherwise be allocated to a TRX. In such a case, the unused timeslots are lost.

The remaining (and consecutive) subslots can therefore be allocated to EDAPs.

g The migration of real configurations can present an empty list of idle timelots. This means that, in real cases, not all the timeslots of the TCH pool can be migrated. However, preprocessing activities done when still using the eBSC/BSC1 (e.g. reconfiguration and leasing of new PCM lines when capacity is not sufficient) are not within the scope of this document.

For general guidelines on dimensioning EDAPs on the Abis interface, refer to “Abis EDGE dimensioning”. For an example PCM allocation, refer to “Example PCM alloca-tion”.

5.2.1 Example

5.3 Frequency hoppingThe exporter tool cannot have clear and unique criteria according to which it can decide whether to drop frequency hopping laws or not. Therefore, you have to reconfig-ure frequency hopping laws according to the guidelines described for other BTS types

Create EDAP Example from Real NetAct Configuration script <managedObject class="DAP" version="S12" distName="PLMN-PLMN/BSC-205283/DAP-1" id="60 2 25 26 596 3 4 </managedObject>

Attribute Range Description

 0-8 The BSCU associated to the PCU serving the DAP pool

 0-31 The 1st 64 Kbps-timeslot of the PCM 0-31 The last 64 Kbps-timeslot (of the

consecutive series started at firstTSL ) of the PCM



0-254 Identifier for the PCM (e.g. 2048 Kbps line for PCM30)

 0-254 id for the PCU 0-99 Packet Service Entity Identifier:

This parameter identifies the PSE object in the BSC.

34DN0933393


Id:0900d80580646c17

Create BTS

in the Nokia Siemens Networks GSM/EDGE BSS product line. Refer to “BSS7005: Fre-quency hopping” for more information.

DN0933393 35


Create BTS

Id:0900d80580646c17

5.4 acDIMinCiRatioEstParameters related to enhanced quality of service (Eqos) are not supported.

5.5 adaptiveLaAlgorithm

5.6 adminState

Obj BTS M,O,N,internal M Val

Full Name Adaptive LA Algorithm Type Enumeration Range Adaptive LA algorithm is enabled (Y) (0), Adaptive LA algorithm is

disabled (N) (1) Internal Value gui_value Default Adaptive LA algorithm is enabled (Y) (0) Description With this parameter the operator can define if the used GPRS Link

Adaptation algorithm is adaptive or not. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

Obj BTS M,O,N,internal M Val

Full Name Administrative State Type Enumeration Range Unlocked (1), Locked (3) Default Locked (3) Description Administrative State of the object in the NW after object creation or

modification. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1

36DN0933393


Id:0900d80580646c17

Create BTS

5.7 amrHoFrInHoThrDlRxQual

5.8 amrHoFrThrDlRxQual

O b j B T S M ,O ,N ,in tern a l m ap p e d Va l

F ul l N a m e In tra H O T h re sh o ld R x Q u a l AM R F R T yp e E n u m e ra tio n R a n g e < 0 .2 % (0 ), 0 .2 % - 0 .4 % (1 ), 0 .4 % - 0 .8% (2) , 0 .8 % - 1 .6% (3) ,

1 .6% - 3.2 % (4 ) , 3 .2% - 6 .4 % (5 ) , 6 .4 % - 1 2 .8 % (6 ) , > 12 .8 % (7 ) In te rn a l Va lu e g u i_ value D e fa u lt < 0 .2 % (0 ) D e sc r ip tio n A M R H a n d o ve r In tra T h resh o ld D l R x Q u a l fo r Fu ll R ate . 3 G p p M u ltip 1 M o di fica tion O n -L in e M o di fie d o n C re ate o p ti on a l V a l E x tra c t fro m Se rv ice G rou p , in ca se it is u se d (m e an va lu e o f)

H a n do ve r S e r vic e G ro u ps for A M R F R s pe e c h c a lls (S e rv ic e G ro up -1 1, S e rv ic e G r o up -12 ) S G xxH O PA R (x= 11 ..1 2 ) = < fie ld 1 > -< fie ld 2 > ..< fie ld 1 0 > = H O L T H L VD L -H O L TH LV U L -H O TD L IN T-H O T U L IN T -H O R X L VD L I-H O R X L V D L O -H O LT H Q U D L -H O LT H Q U U L -H O T H C D L -H O T H C U L o the rw ise se t it e q ua l to m e a n va lu e o f H O L TH Q U D L -H O L T H Q U U L o the rw ise se t it e q ua l to d e fa ul t.(0 )

O b j B TS M ,O ,N ,in tern a l M Va l

F ul l N ame T h res ho ld D l R x Q ua l F o r A M R FR T ype E n umera tio n R ange < 0 .2% (0 ), 0 .2% - 0.4 % (1 ), 0 .4% - 0 .8 % (2 ), 0 .8% - 1 .6% (3 ), 1.6%

- 3 .2% (4 ), 3 .2 % - 6 .4% (5 ), 6 .4 % - 12 .8% (6) , > 12 .8% (7 ) In te rna l Va lue gu i_va lue D e fau lt 1 .6% - 3 .2% (4 ) D escr ip tio n A m r H and ove r D l R x Q ua l fo r F ul l R a te. 3 G p p M u ltip 1 M o di fica tion O n-L ine M o di fied o nC re ate op tiona l Va l E xtract from S erv ice Gro up , in c ase it is use d

H and ov er S erv ic e G ro up s fo r A MR FR sp eec h ca lls (Se rvice G ro up -11 , Se rv ice G rou p -12 ) S G xxH O P AR (x=11 ..12) = <fie ld 1 >-<fie ld 2> ..<fie ld 10> = H O L TH LV D L-H O LTH LV U L -H OT D LIN T -H O TU LIN T-H O R X L VD LI-H O R XL V D LO -H O L T H Q U D L -H O L TH Q U U L -H O T H C D L-H O T H C U L o the rw ise se t it eq ua l to H O LTH Q U D L [0-2 0 ] o the rw ise se t it eq ua l to defau lt.(4 )

DN0933393 37


Create BTS

Id:0900d80580646c17

5.9 amrHoFrThrUlRxQual

5.10 amrHoHrInHoThrDlRxQual

O bj B TS M ,O ,N ,in tern a l M Va l

F ul l N ame T h res ho ld U l R x Q ua l A M R FR T ype E n umera tio n R ange < 0 .2% (0 ), 0 .2% - 0.4 % (1 ), 0 .4% - 0 .8 % (2 ), 0 .8% - 1 .6% (3 ), 1.6%

- 3 .2% (4 ), 3 .2 % - 6 .4% (5 ), 6 .4 % - 12 .8% (6) , > 12 .8% (7 ) In te rna l Va lue gu i_va lue D e fau lt 1 .6% - 3 .2% (4 ) D escr ip tio n A M R H a ndove r T hresh o ld U l R x Q u a l for F u ll R a te . 3 G p p M u ltip 1 M o di fica tion O n-L ine M o di fied o nC re ate op tiona l Va l E xtract from S erv ice Gro up , in c ase it is use d

H and ov er S erv ic e G ro up s fo r A MR FR sp eec h ca lls (Se rvice G ro up -11 , Se rv ice G rou p -12 ) S G xxH O P AR (x=11 ..12) = <fie ld 1 >-<fie ld 2> ..<fie ld 10> = H O L TH LV D L-H O LTH LV U L -H OT D LIN T -H O TU LIN T-H O R X L VD LI-H O R XL V D LO -H O L T H Q U D L -H O L TH Q U U L -H O T H C D L-H O T H C U L o the rw ise se t it eq ua l to H O LTH Q U U L [0-2 0 ] o the rw ise se t it eq ua l to defau lt.(4 )

Obj BTS M,O,N,internal mapped Val

Full Name AMR Handover HR Intra Threshold DL Rx Qual Type Enumeration Range < 0.2% (0), 0.2% - 0.4% (1), 0.4% - 0.8% (2), 0.8% - 1.6% (3),

1.6% - 3.2% (4), 3.2% - 6.4% (5), 6.4% - 12.8% (6), > 12.8% (7)

Internal Value gui_value Default 1.6% - 3.2% (4) Description AMR Handover Intra Threshold Dl Rx Qual for Half Rate. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [HAND] HOTHDDL.

38DN0933393


Id:0900d80580646c17

Create BTS

5.11 amrHoHrThrDlRxQual

5.12 amrHoHrThrUlRxQual

O bj BT S M ,O ,N ,in tern a l M V a l

F ul l N ame T hresho ld D l R x Q u a l AM R H R T ype Enum e ra tion R ange < 0 .2% (0 ), 0 .2 % - 0 .4% (1 ), 0 .4 % - 0 .8 % (2 ), 0 .8% - 1 .6 % (3 ), 1 .6%

- 3.2 % (4 ), 3 .2% - 6 .4 % (5 ), 6 .4% - 12 .8% (6 ), > 12.8% (7 ) In te rna l Va lue gu i_va lue D e fau lt 1 .6% - 3 .2 % (4) D escr ip tio n AM R H and ove r T h res ho ld D l R x Q ua l fo r H a lf R a te . 3 G p p M u ltip 1 M o di fica tion O n-Line M o di fied o nC re ate op tiona l Va l Extra ct fro m Serv ice G roup , in ca se it is used

H an do v er Se rv ice G rou ps fo r A M R H R s p e ech c a lls (Service G ro u p-13 , Se rv ice G ro up -14) SG xxH O PAR (x= 13..1 4 ) = <fie ld 1>-<fie ld 2 >..< fie ld 10 > = H O LT H LVD L -H O L T H LVU L-H O T D LIN T-H O T U LIN T -H O R XLVD LI-H O R X LVD L O -H O L TH Q U D L-H O LT H Q U U L -H O T H D D L-H O TH D U L o therw ise se t it equ al to H O LT H Q U D L [0 -2 0] o therw ise se t it equ al to d e fau lt.(4 )

O b j BT S M ,O ,N ,in tern a l M V a l

F ul l N ame T hresho ld U l R x Q u a l AM R H R T ype Enum e ra tion R ange < 0 .2% (0 ), 0 .2 % - 0 .4% (1 ), 0 .4 % - 0 .8 % (2 ), 0 .8% - 1 .6 % (3 ), 1 .6%

- 3.2 % (4 ), 3 .2% - 6 .4 % (5 ), 6 .4% - 12 .8% (6 ), > 12.8% (7 ) In te rna l Va lue gu i_va lue D e fau lt 1 .6% - 3 .2 % (4) D escr ip tio n AM R H and ove r T h res ho ld U l R x Q ua l fo r H a lf R a te . 3 G p p M u ltip 1 M o di fica tion O n-Line M o di fied o nC re ate op tiona l Va l Extra ct fro m Serv ice G roup , in ca se it is used

H an do v er Se rv ice G rou ps fo r A M R H R s p e ech c a lls (Service G ro u p-13 , Se rv ice G ro up -14) SG xxH O PAR (x= 13..1 4 ) = <fie ld 1>-<fie ld 2 >..< fie ld 10 > = H O LT H LVD L -H O L T H LVU L-H O T D LIN T-H O T U LIN T -H O R XLVD LI-H O R X LVD L O -H O LTH Q U D L-H O LT H Q U U L -H O T H D D L-H O TH D U L o therw ise se t it equ al to H O LT H Q U U L [0 -2 0] o therw ise se t it equ al to d e fau lt.(4 )

DN0933393 39


Create BTS

Id:0900d80580646c17

5.13 amrPocFrPcLThrDlRxQual

5.14 amrPocFrPcLThrUlRxQual

O b j B TS M ,O ,N ,in tern a l M .m ap p e d V a l

F ul l N a m e P C L ow e r T h re sh o ld D l R x Q u a l A M R F R T yp e E nu m e ra ti on R a n g e < 0 .2 % (0 ) , 0.2 % - 0 .4 % (1 ) , 0 .4 % - 0 .8 % (2 ) , 0 .8 % - 1 .6 % (3 ) ,

1 .6 % - 3 .2 % (4 ), 3 .2 % - 6 .4% (5) , 6 .4 % - 1 2.8 % (6 ) , > 1 2 .8% (7 )In te rn a l Va lu e g u i_ va lu e D e fa u lt 0 .8 % - 1 .6 % (3 ) D e sc r ip tio n D e fin e s th e A M R P o w e r C o n tro l p a ra m e te rs for F u ll R a te . 3 G p p M u ltip 1 M o di fica tion O n -L in e M o di fie d o n C re ate o p tio n a l V a l E x tra c t fro m S erv ic e G ro u p , in ca se it is u se d

P ow e r C on tro l Se rv ic e fo r A M R sp e e c h c a lls (S er v ic e G r ou p -1 1 ..S e r vic e G ro u p-1 2 ) S G xxP C P A R (x=1 1 ..1 2 , AM R FR c al ls ) = < fie ld 1 > -< fie ld 2 > ..< fi eld 1 6 > = E B S PW R C -E M S P W R C -E P W C R L F W -L O W T L EV D -L O W T L E V U -U P T L E V D -U P T LE V U -P C R L F TH -L OW TQ U A D -L OW TQ U A U -U P TQ U A D -U P T Q U A U -R D LN K T B S -R D L N K T O o th e rw ise se t it e q u a l to L O W TQ U A D [0 -2 0 ] o th e rw ise se t it e q u a l to d e fa u lt.(3 )

O b j B TS M ,O ,N ,in tern a l M .m ap p e d V a l

F ul l N a m e P C L ow e r T h re sh o ld U l R x Q u a l A M R F R T yp e E nu m e ra ti on R a n g e < 0 .2 % (0 ) , 0.2 % - 0 .4 % (1 ) , 0 .4 % - 0 .8 % (2 ) , 0 .8 % - 1 .6 % (3 ) ,

1 .6 % - 3 .2 % (4 ), 3 .2 % - 6 .4% (5) , 6 .4 % - 1 2.8 % (6 ) , > 1 2 .8% (7 )In te rn a l Va lu e g u i_ va lu e D e fa u lt 0 .8 % - 1 .6 % (3 ) D e sc r ip tio n D e fin e s th e A M R P o w e r C o n tro l p a ra m e te rs for F u ll R a te . 3 G p p M u ltip 1 M o di fica tion O n -L in e M o di fie d o n C re ate o p tio n a l V a l E x tra c t fro m S erv ic e G ro u p , in ca se it is u se d

P ow e r C on tro l Se rv ic e fo r A M R sp e e c h c a lls (S er v ic e G r ou p -1 1 ..S e r vic e G ro u p-1 2 ) S G xxP C P A R (x=1 1 ..1 2 , AM R FR c al ls ) = < fie ld 1 > -< fie ld 2 > ..< fi eld 1 6 > = E B S PW R C -E M S P W R C -E P W C R L F W -L O W T L EV D -L O W T L E V U -U P T L E V D -U P T LE V U -P C R L F TH -L O W T Q U AD -L O W T Q U A U -U P TQ U A D -U P T Q U A U -R D LN K T B S -R D L N K T O o th e rw ise se t it e q u a l to L O W TQ U A U [0 -2 0 ] o th e rw ise se t it e q u a l to d e fa u lt.(3 )

40DN0933393


Id:0900d80580646c17

Create BTS

5.15 amrPocFrPcUThrDlRxQual

5.16 amrPocFrPcUThrUlRxQual

O b j B TS M ,O ,N ,in tern a l M V a l

F ul l N a m e P C U p p e r T h res ho ld D l R x Q u a l A M R FR T yp e E n u m e ra tio n R a n g e < 0 .2 % (0 ) , 0 .2% - 0.4 % (1 ) , 0 .4 % - 0 .8 % (2 ) , 0 .8 % - 1 .6 % (3 ) ,

1 .6 % - 3 .2 % (4 ) , 3 .2 % - 6 .4 % (5 ) , 6 .4 % - 1 2 .8 % (6 ), > 1 2 .8 % (7 )

In te rn a l Va lu e g u i_ va lu e D e fa u lt < 0 .2 % (0 ) D e sc r ip tio n D e fine s th e A M R P ow er C o n tro l pa ra m ete rs fo r F u ll R a te . 3 G p p M u ltip 1 M o di fica tion O n -L in e M o di fie d o n C re ate o p tio n a l V a l E x trac t fro m S e rv ice G ro u p , in c as e it is u se d o th erw is e se t it

e q u a l to d efa u lt.(0 ) P ow er C o ntro l Se r vic e for A M R s pe e c h c a lls (S e rv ic e G r o up -13 ..S e r v ice G r ou p -1 4 ) S G xxP C P A R (x= 1 3..1 4 , A M R H R ca ll s ) = < fie ld 1 > -< fie ld 2> ..< fie ld 16 > = E BS PW R C -EM S P W R C -E P W C R L FW -L O W T L EV D -L O W TL E V U -U P T L E V D -U P T L E V U -P C R L F TH -L O W T Q U A D -L O W TQ U A U -U PT Q U A D -U P TQ U A U -R D L N KT B S -R D L N K T O

O b j B TS M ,O ,N ,in tern a l M V a l

F ul l N a m e P C U p p e r T h res ho ld U l R x Q u a l A M R FR T yp e E n u m e ra tio n R a n g e < 0 .2 % (0 ) , 0 .2% - 0.4 % (1 ) , 0 .4 % - 0 .8 % (2 ) , 0 .8 % - 1 .6 % (3 ) ,

1 .6 % - 3 .2 % (4 ) , 3 .2 % - 6 .4 % (5 ) , 6 .4 % - 1 2 .8 % (6 ), > 1 2 .8 % (7 )

In te rn a l Va lu e g u i_ va lu e D e fa u lt < 0 .2 % (0 ) D e sc r ip tio n D e fine s th e A M R P ow er C o n tro l pa ra m ete rs fo r F u ll R a te . 3 G p p M u ltip 1 M o di fica tion O n -L in e M o di fie d o n C re ate o p tio n a l V a l E x trac t fro m S e rv ice G ro u p , in c as e it is u se d o th erw is e se t it

e q u a l to d efa u lt.(0 ) P ow er C o ntro l Se r vic e for A M R s pe e c h c a lls (S e rv ic e G r o up -11 ..S e r v ice G r ou p -1 2 ) S G xxP C P A R (x= 1 1..1 2 , A M R H R ca ll s ) = < fie ld 1 > -< fie ld 2> ..< fie ld 16 > = E BS PW R C -EM S P W R C -E P W C R L FW -L O W T L EV D -L O W TL E V U -U P T L E V D -U P T L E V U -P C R L F TH -L O W T Q U A D -L O W TQ U A U -U PT Q U A D -U P T Q U A U -R D L N KT B S -R D L N K T O

DN0933393 41


Create BTS

Id:0900d80580646c17

5.17 amrPocHrPcLThrDlRxQual

5.18 amrPocHrPcLThrUlRxQual

O b j BT S M ,O ,N ,in tern a l M .m a p p e d Va l

F ul l N a me PC L o w e r Th re sh o ld D l R x Q u al AM R H R T yp e En u m era tio n R a n g e < 0 .2 % (0 ), 0 .2 % - 0 .4% (1) , 0 .4 % - 0 .8 % (2 ) , 0 .8 % - 1.6 % (3 ) ,

1 .6 % - 3 .2 % (4 ) , 3 .2 % - 6 .4 % (5 ) , 6.4 % - 1 2 .8 % (6 ) , > 1 2 .8 % (7 )

In te rn a l Va lu e g ui_va lu e D e fa u lt 0 .8 % - 1 .6 % (3 ) D e scr ip tio n D e fin e s th e AM R P o w e r C on tro l p ara m e ters fo r H a lf R a te. 3 G p p M u ltip 1 M o di fica tion O n -L in e M o di fie d o n C re ate o ptio n a l Va l Extra c t fro m Se rv ice G ro u p , in ca se it i s us ed

Po w e r C o ntrol Se r v ice fo r A M R s p ee c h c alls (Se rvic e G ro up -1 3 ..S e rv ic e G ro up -14 ) SG xxP C PA R (x=1 3 ..1 4 , AM R H R ca lls ) = < fie ld 1 >-<fie ld 2 > ..< fie ld 1 6 > = EB SPW R C -EM S PW R C -E PW C R L FW -L O W TL EV D -L O W T LE VU -U P TL E VD -U PT L EV U -PC R LF T H -L O W T Q U A D -L O W T Q U A U -U PT Q U AD -U P TQ U AU -R D L N K TB S-R D L N K TO o th e rw ise se t it e qu a l to L O W T Q U AD [0 -2 0 ] o th e rw ise se t it e qu a l to d e fau lt.(3 )

O b j B T S M ,O ,N ,in tern a l M .m a p p e d V a l

F ul l N a m e P C L o w e r Th re s h o ld U l R x Q u al A M R H R T y p e E n u m era t io n R a n g e < 0 .2 % (0 ), 0 .2 % - 0 .4% (1) , 0 .4 % - 0 .8 % (2 ) , 0 .8 % - 1.6 % (3 ) ,

1 .6 % - 3 .2 % (4 ) , 3 .2 % - 6 .4 % (5 ) , 6.4 % - 1 2 .8 % (6 ) , > 1 2 .8 % (7 )

In te rn a l V a lu e g ui _v a lu e D e fa u lt 0 .8 % - 1 .6 % (3 ) D e s c r ip t io n D e fin e s th e A M R P o w e r C on tro l p ara m e ters fo r H a lf R a te. 3 G p p M u lt ip 1 M o di f ic a t ion O n -L in e M o di f ie d o n C re ate o ptio n a l V a l E x tra c t fro m S e rv ic e G ro u p , in c a s e it i s us ed

P o w e r C o nt r o l S e r v ice fo r A M R s p ee c h c alls (S e r vic e G ro up -1 3 ..S e rv ic e G r o up -14 ) S G x x P C P A R (x = 1 3 ..1 4 , A M R H R c a lls ) = < fie ld 1 > -< f ie ld 2 > ..< f ie ld 1 6 > = E B S P W R C -E M S P W R C -E P W C R L FW -L O W TL E V D -L O W T LE V U -U P TL E V D -U P T L E V U -P C R LF T H -L O W TQ U A D -LO W TQ U A U -U P T Q U A D -U P TQ U A U -R D L N K TB S -R D L N K TO o th e rw is e s e t it e qu a l to L O W T Q U A U [0 -2 0 ] o th e rw is e s e t it e qu a l to d e fau lt. (3 )

42DN0933393


Id:0900d80580646c17

Create BTS

5.19 amrPocHrPcUThrDlRxQual

5.20 amrPocHrPcUThrUlRxQual

O b j B T S M ,O ,N ,in tern a l M V a l

F ul l N a m e P C U p pe r T hre sh o ld D l R x Q u a l AM R H R T yp e E n u m e ra tio n R a n g e < 0 .2 % (0 ) , 0 .2 % - 0 .4 % (1 ), 0 .4 % - 0 .8 % (2 ), 0 .8 % - 1 .6 % (3 ),

1 .6 % - 3 .2 % (4) , 3 .2 % - 6 .4 % (5 ) , 6 .4% - 12 .8 % (6 ) , > 1 2 .8 % (7 )

In te rn a l Va lu e g u i_ va lu e D e fa u lt < 0 .2 % (0 ) D e sc r ip tio n D e fin e s th e A M R P o w e r C o n tro l p a ram e te rs fo r H a lf R a te . 3 G p p M u ltip 1 M o di fica tion O n -Li ne M o di fie d o n C re ate o p tio n al V a l E x tra c t fro m Se rv ice G ro up , in ca se it is u se d oth e rw ise se t it

e q u al to d e fa u lt.(0 ) P o w e r C on tr o l S e rv ic e fo r A M R s p e e ch c a lls (Se r v ic e G ro u p-1 3 ..S e rv ic e G ro up -1 4 ) S G xxP C P A R (x=1 3 ..1 4 , A M R H R ca lls ) = < fi el d 1 > -< fie ld 2 > ..< fie ld 1 6 > = E B S P W R C -E M S P W R C -E PW C R L F W -L OW TL E V D -L O W T L EV U -U P T LE VD -U P TL E VU -PC R L FT H -L O W T QU A D -L O W T Q U A U -U P TQ U A D -U P T Q U AU -R D L N KT B S -R D L N K T O

O b j B T S M ,O ,N ,in tern a l M V a l

F ul l N a m e P C U p pe r T hre sh o ld U l R x Q u a l AM R H R T yp e E n u m e ra tio n R a n g e < 0 .2 % (0 ) , 0 .2 % - 0 .4 % (1 ), 0 .4 % - 0 .8 % (2 ), 0 .8 % - 1 .6 % (3 ),

1 .6 % - 3 .2 % (4) , 3 .2 % - 6 .4 % (5 ) , 6 .4% - 12 .8 % (6 ) , > 1 2 .8 % (7 )

In te rn a l Va lu e g u i_ va lu e D e fa u lt < 0 .2 % (0 ) D e sc r ip tio n D e fin e s th e A M R P o w e r C o n tro l p a ram e te rs fo r H a lf R a te . 3 G p p M u ltip 1 M o di fica tion O n -Li ne M o di fie d o n C re ate o p tio n al V a l E x tra c t fro m Se rv ice G ro up , in ca se it is u se d oth e rw ise se t it

e q u al to d e fa u lt.(0 ) P o w e r C on tr o l S e rv ic e fo r A M R s p e e ch c a lls (Se r v ic e G ro u p-1 3 ..S e rv ic e G ro up -1 4 ) S G xxP C P A R (x=1 3 ..1 4 , A M R H R ca lls ) = < fi el d 1 > -< fie ld 2 > ..< fie ld 1 6 > = E B S P W R C -E M S P W R C -E PW C R L F W -L OW TL E V D -L O W T L EV U -U P T LE VD -U P TL E VU -PC R L FT H -L O W T QU A D -L O W T Q U A U -U P TQ U A D -U P TQ U A U -R D L N KT B S -R D L N K T O

DN0933393 43


Create BTS

Id:0900d80580646c17

5.21 antennaHopping

5.22 bcchGSM900BandBSDATA internal parameter (must not be set)

5.23 bsIdentityCodeBCC

Obj BTS M,O,N,internal Mapped Val Full Name Antenna Hopping Type Enumeration Range antenna hopping not used (N) (0), antenna hopping used (Y) (1) Internal Value gui_value Default antenna hopping not used (N) (0) Description Defines whether antenna hopping is used in the BTS or not. 3Gpp Multip 1 Modification Requires object locking Modified BTS must be locked onCreate Optional Val [BTS] EANTHOP:

• TRUE ? 1 • FALSE? 0

Obj BTS M,O,N,internal M.mapped Val Full Name BSIC BCC Type Number Range 0...7, step 1 Internal Value gui_value Default Description Identifies the BTS colour code number 3Gpp Multip 1 Modification Requires object locking Modified When BTS is locked onCreate mandatory Val BCC field of [BTS] BSIC

44DN0933393


Id:0900d80580646c17

Create BTS

5.24 bsIdentityCodeNCC

5.25 cellId

Obj BTS M,O,N,internal M.mapped Val Full Name BSIC NCC Type Number Range 0...7, step 1 Internal Value gui_value Default Description Identifies the network colour code number3Gpp Multip 1 Modification Requires object locking Modified When BTS is locked onCreate mandatory Val NCC field of [BTS] BSIC

Obj BTS M,O,N,internal M.mapped Val Full Name CI Type Number Range 0...65535, step 1 Internal Value gui_value Default Description Identifies the cells within a location area 3Gpp Multip 1 Modification Requires object locking Modified All BTSs of the segment must be in a LOCKED stateonCreate mandatory Val CI field of [BTS] CELLGLID

DN0933393 45


Create BTS

Id:0900d80580646c17

5.26 cellNumberInBtsHW

5.27 directGPRSAccessBts

Obj BTS M,O,N,internal M (CR: New BTS operator parameter to determine BSxx cellNumber) Val

Full Name cellNumberInBtsHW I Type Number Range 0...11, step 1 Internal Value gui_value Default Description Mediation will map this parameter 1:1 onto already existing BTS internal attribute

“segmentId” (BTS level) which is sent within the alignment procedure towards BSxx O&M SW

3Gpp Multip 1 Modification Not modifiable Modified onCreate mandatory Val Assigned from the BTS relative number (e.g. it is 1 in the following example

CREATE BTS:NAME=BTSM:0/BTS:1). Note: In case of BR Dual Band cells (which are splitted in a pair (master/slave) of BSS BTS) each of the 2 BTS, presents the same value for cellNumberInBtsHW.

Obj BTS M,O,N,internal M Val

Full Name Direct GPRS Access BTS Type Number Range -40...40, step 1 Internal Value gui_value Default 0 Description Attribute defines which BTSs may be used for GPRS or EGPRS

without signal level measurements. The parameter non BCCH layer offset is ignored. This is used in initial channel allocation and reallocation.

46DN0933393


Id:0900d80580646c17

Create BTS

5.28 egprsInitMcsAckMode

5.29 egprsInitMcsUnAckMode

Obj BTS M,O,N,internal M Val

Full Name Initial MCS For Acknowledged Mode Type Number Range 1...9, step 1 Internal Value gui_value Default 6 Description EGPRS link adaptation parameter. Indicates the Modulation and

Coding Scheme (MCS) used at the beginning of a TBF for acknowledged mode.


Obj BTS M,O,N,internal M Val

Full Name Initial MCS For Unacknowledged Mode Type Number Range 1...9, step 1 Internal Value gui_value Default 5 Description EGPRS link adaptation parameter.Indicates the MCS used at the

beginning of a TBF for unacknowledged mode. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 5

DN0933393 47


Create BTS

Id:0900d80580646c17

5.30 egprsLinkAdaptEnabled

5.31 egprsMaxBlerAckMode

Obj BTS M,O,N,internal M Val

Full Name EGPRS Link Adaptation Enabled Type Enumeration Range EGPRS link adaptation is disabled (0), enabled for RLC

acknowledged mode (1), enabled for RLC acknowledged and unacknowledged (2)

Internal Value gui_value Default enabled for RLC acknowledged and unacknowledged (2) Description With this parameter you enable or disable EGPRS link adaptation

on cell level. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 2

Obj BTS M,O,N,internal M Val

Full Name Maximum BLER In Acknowledged Mode Type Number Range 10...100 %, step 1 % Internal Value gui_value Default 90 % Description EGPRS link adaptation parameter. Indicates the maximum block

error rate of first transmission in acknowledged mode. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 90

48DN0933393


Id:0900d80580646c17

Create BTS

5.32 egprsMaxBlerUnAckMode

5.33 egprsMeanBepOffset8psk

Obj BTS M,O,N,internal M Val

Full Name Maximum BLER In Unacknowledged Mode Type Number Range 1...100, step 1 Internal Value gui_value Default 10 Description EGPRS link adaptation parameter. Indicates the maximum block

error rate in unacknowledged mode. The unit is parts per thousand.


Obj BTS M,O,N,internal M Val Ful l Name Mean BEP Offset 8PSK Type Number Range -31...31, step 1 Internal Value gui_value Default 0 Description EGPR S link adaptation parameter.3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

DN0933393 49


Create BTS

Id:0900d80580646c17

5.34 egprsMeanBepOffsetGmsk

5.35 frequencyBandInUse

Obj BTS M,O,N,internal M Val Full Name Mean BEP Offset GMSK Type Number Range -31...31, step 1 Internal Value gui_value Default 0 Description EGPRS link adaptation parameter. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

Obj BTS M,O,N,internal M Val

Full Name Frequency Band In Use Type Enumeration Range GSM 900 (0), GSM 1800 (1), GSM 1900 (2), GSM 800 (5) Internal Value gui_value Default GSM 900 (0) Description Frequency band used in the BTS 3Gpp Multip 1 Modification Not modifiable Modified onCreate mandatory Val [BTS} SYSID

• BB900 or EXT900 GSM900; • DCS1800 GSM1800; • PCS1900 GSM1900; • GSM850 GSM800; • GSMDCS GSM900 or GSM1800 according to where

is allocated the BCCH frequency (and also according to BTS type (primary or not: when a BR dual band BTS is splitted into a pair of BSS BTS)

• GSM850DCS GSM800 or GSM1800 according to where is allocated the BCCH frequency (and also according to BTS type (primary or not: when a BR dual band BTS is splitted into a pair of BSS BTS)

• GSM850PCS GSM800 or GSM1900 according to where is allocated the BCCH frequency (and also according to BTS type (primary or not: when a BR dual band BTS is splitted into a pair of BSS BTS)

• GSMR : not supported

50DN0933393


Id:0900d80580646c17

Create BTS

5.36 gprsEnabled

5.37 gprsMsTxPwrMaxCCH1x00

Obj BTS M,O,N,internal M Val

Full Name GPRS Enabled Type Enumeration Range GPRS is disabled (N) (0), GPRS is enabled (Y) (1) Internal Value gui_value Default GPRS is disabled (N) (0) Description The attribute is used to enable or disable the GPRS capabil ity during the

normal operation of the cell. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 0

Obj BTS M,O,N,internal M Val

Full Name GPRS MS Txpwr Max CCH 1x00 Type Number Range 0...36, step 2 Internal Value gui_value Default 30 Description With this parameter you define the maximum transmission

power level a mobile station may use when accessing a packet control channel in the cell for GSM 1800/1900 bands.

DN0933393 51


Create BTS

Id:0900d80580646c17

5.38 gprsMsTxpwrMaxCCH

5.39 gprsNonBCCHRxlevLower

Obj BTS M,O,N,internal M Val

Full Name GPRS MS Txpwr Max CCH Type Number Range 5...39 dBm, step 2 dBm Internal Value (gui_value - 43) / -2 Default 33 dBm Description Attribute defines maximum transmission power level a mobile

station may use when accessing a packet control channel in the cell.


Obj BTS M,O,N,internal M Val

Full Name GPRS Non BCCH Layer Rxlev Lower Limit Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -100 dBm Description Attribute defines the threshold when reallocation to better BTS

must be done. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 10

52DN0933393


Id:0900d80580646c17

Create BTS

5.40 gprsNonBCCHRxlevUpper

5.41 gprsRxlevAccessMin

Obj BTS M,O,N,internal M Val

Full Name GPRS Non BCCH Layer Rxlev Upper Limit Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -95 dBm Description Attribute defines minimum power level the MS has to receive to

allocate resources from the BTS. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 15

Obj BTS M,O,N,internal M Val

Full Name GPRS Rxlev Access Min Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -105 dBm Description Attribute defines minimum power level the mobile station has to

receive before it is allowed to access the cell. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 5

DN0933393 53


Create BTS

Id:0900d80580646c17

5.42 hcsPriorityClass

5.43 hcsThreshold

Obj BTS M,O,N,internal Mapped Val

Full Name Priority Class Type Number Range 0...7, step 1 Internal Value gui_value Default 0 Description Attribute indicates he HCS (hierarchical cell s tructures) priority for the

cells. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] PL / (15 / 7)

Obj BTS M,O,N,internal M Val

Full Name HCS Threshold Type Number Range -110...-48 dB, step 2 dB Internal Value (gui_value + 110) / 2 Default 255 dB Description Attribute defines signal strength threshold for applying HCS in GPRS and

LSA reselection. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 255

54DN0933393


Id:0900d80580646c17

Create BTS

5.44 hoppingMode

5.45 hoppingSequenceNumber1

Obj BTS M,O,N,internal mapped Val Full Name BTS Hopping Mode Type Enumeration Range Non-hopping (0), Baseband hopping (1), Radio Frequency hopping (2) Internal Value gui_value Default Non-hopping (0) Description With this parameter you define the frequency hopping mode of the BTS.3Gpp Multip 1 Modification Requires object locking Modified When BTS is locked onCreate optional Val [BTS].HOPMODE:

• BBHOP 1 • SYNHOP 2

Obj BTS M,O,N,internal M.mapped Val

Full Name Hopping Sequence Number 1 Type Number Range 0...63, step 1 Internal Value gui_value Default 0 Description With this parameter you define whether cyclic or random

hopping is used in BB hopping group 1 and in RF hopping. 3Gpp Multip 1 Modification Requires object locking Modified When BTS is locked onCreate optional Val

0 : Migration tool does not rebuild hopping laws, in case there were any. Thus hopping is turned off, after migration.

DN0933393 55


Create BTS

Id:0900d80580646c17




Full Name Hopping Sequence Number 2 Type Number Range 0...63, step 1 Internal Value gui_value Default 0 Description With this parameter you define whether cyclic or random

hopping is used in BB hopping group 2 3Gpp Multip 1 Modification Requires object locking Modified When BTS is locked onCreate optional Val

0 : Migration tool does not rebuild hopping laws, in case there were any. Thus hopping is turned off, after migration.


Full Name Underlay Hopping Sequence Number Type Number Range 0...63, step 1 Internal Value gui_value Default 0 Description With this parameter you define whether cyclic or random

hopping is used in the underlay layer of the IUO cell 3Gpp Multip 1 Modification Requires object locking Modified When BTS is locked onCreate optional Val 0

Migration tool does not rebuild hopping laws, in case there were any. Thus hopping is turned off, after migration.

56DN0933393


Id:0900d80580646c17

Create BTS

5.48 inactEndTimeHour

5.49 inactEndTimeMinute

Obj BTS M,O,N,internal M Val

Full Name EGPRS Inactivity Alarm End Time Hour Type Number Range 0...23 h, step 1 h Internal Value gui_value Default 18 h Description This parameter determines the time of day when the EGPRS inactivity

alarm is disabled. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 18

Obj BTS M,O,N,internal M Val

Full Name EGPRS Inactivity Alarm End Time Minute Type Number Range 0...45 min, step 15 min Internal Value gui_value Default 0 min Description This parameter determines the time of day when the EGPRS

inactivity alarm is disabled. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

DN0933393 57


Create BTS

Id:0900d80580646c17

5.50 inactStartTimeHour

5.51 inactStartTimeMinute

Obj BTS M,O,N,internal M Val

Full Name EGPRS Inactivity Alarm Start Time Hour Type Number Range 0...23 h, step 1 h Internal Value gui_value Default 8 h Description This parameter determines the time of day when the EGPRS inactivity

alarm is enabled. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 8

Obj BTS M,O,N,internal M Val

Full Name EGPRS Inactivity Alarm Start Time Minute Type Number Range 0...45 min, step 15 min Internal Value gui_value Default 0 min Description This parameter determines the time of day when the EGPRS

inactivity alarm is enabled. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

58DN0933393


Id:0900d80580646c17

Create BTS

5.52 inactWeekDays

5.53 csAckDl

Obj BTS M,O,N,internal M Val

Full Name EGPRS Inactivity Alarm Weekdays Type Bitmask Range Bit 0: Sunday, Bit 1: Saturday, Bit 2: Friday, Bit 3: Thursday, Bit 4:

Wednesday, Bit 5: Tuesday, Bit 6: Monday

Internal Value gui_value Default 0 Description This parameter determines the day of week when the EGPRS inactivity

alarm is enabled. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

Obj BTS M,O,N,internal M Val

Full Name DL Coding Scheme In Acknowledged Mode Type Enumeration Range CS1 (0), CS2 (1), CS3 (2), CS4 (3), LA with initial CS1 (4), LA with initial CS2 (5),

LA with initial CS3 (6), LA with initial CS4 (7) Internal Value gui_value Default CS2 (1) Description With this parameter you can define the initial Coding Scheme of the territory in

acknowledge mode in downlink direction. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1

DN0933393 59


Create BTS

Id:0900d80580646c17

5.54 csAckUl

5.55 csExtAckDl

Obj BTS M,O,N,internal M Val

Full Name UL Coding Scheme In Acknowledged Mode Type Enumeration Range CS1 (0), CS2 (1), CS3 (2), CS4 (3), LA with initial CS1 (4), LA with initial CS2 (5),

LA with initial CS3 (6), LA with initial CS4 (7) Internal Value gui_value Default CS2 (1) Description With this parameter you can define the initial Coding Scheme of the territory in

acknowledge mode in uplink direction. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 1

Obj BTS M,O,N,internal M Val

Full Name DL Coding Scheme In Ext Area Acknowledged Mode Type Enumeration Range CS1 (0), CS2 (1), CS3 (2), CS4 (3), LA with initial CS1 (4), LA with initial CS2

(5), LA with initial CS3 (6), LA with initial CS4 (7) Internal Value gui_value Default CS1 (0) Description Parameter defines the initial DL GPRS coding scheme to be used for RLC ack

mode in the extended coverage area of an extended cell. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

60DN0933393


Id:0900d80580646c17

Create BTS

5.56 csExtAckUl

5.57 csExtUnackDl

Obj BTS M,O,N,internal M Val

Full Name UL Coding Scheme In Ext Area Acknowledged Mode Type Enumeration Range CS1 (0), CS2 (1), CS3 (2), CS4 (3), LA with initial CS1 (4), LA with initial CS2

(5), LA with initial CS3 (6), LA with initial CS4 (7) Internal Value gui_value Default CS1 (0) Description Parameter defines the initial UL GPRS coding scheme to be used for RLC ack

mode in the extended coverage area of an extended cell. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

Obj BTS M,O,N,internal M Val

Full Name DL Coding Scheme In Ext Area Unacknowledged Mode Type Enumeration Range CS1 (0), CS2 (1), CS3 (2), CS4 (3), LA with initial CS1 (4), LA with initial

CS2 (5), LA with initial CS3 (6), LA with initial CS4 (7) Internal Value gui_value Default CS1 (0) Description Parameter defines the initial DL GPRS coding scheme to be used for RLC

unack mode in the extended coverage area of an extended cell. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

DN0933393 61


Create BTS

Id:0900d80580646c17

5.58 csExtUnackUl

5.59 csUnackDl

Obj BTS M,O,N,internal M Val

Full Name UL Coding Scheme In Ext Area Unacknowledged Mode Type Enumeration Range CS1 (0), CS2 (1), CS3 (2), CS4 (3), LA with initial CS1 (4), LA with initial

CS2 (5), LA with initial CS3 (6), LA with initial CS4 (7) Internal Value gui_value Default CS1 (0) Description Parameter defines the initial UL GPRS coding scheme to be used for RLC

unack mode in the extended coverage area of an extended cell. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

Obj BTS M,O,N,internal M Val

Full Name DL Coding Scheme In Unacknowledged Mode Type Enumeration Range CS1 (0), CS2 (1), CS3 (2), CS4 (3), LA with initial CS1 (4), LA with initial CS2

(5), LA with initial CS3 (6), LA with initial CS4 (7) Internal Value gui_value Default CS2 (1) Description With this parameter you can define the initial Coding Scheme of the territory in

unacknowledged mode in downlink direction. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 1

62DN0933393


Id:0900d80580646c17

Create BTS

5.60 csUnackUl

5.61 initMcsExtAckMode

Obj BTS M,O,N,internal M Val

Full Name UL Coding Scheme In Unacknowledged Mode Type Enumeration Range CS1 (0), CS2 (1), CS3 (2), CS4 (3), LA with initial CS1 (4), LA with initial CS2

(5), LA with initial CS3 (6), LA with initial CS4 (7) Internal Value gui_value Default CS2 (1) Description With this parameter you can define the initial Coding Scheme of the territory in

unacknowledged mode in uplink direction. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 1

Obj BTS M,O,N,internal M Val

Full Name Initial MCS For Ext Area Acknowledged Mode Type Number Range 1...9, step 1 Internal Value gui_value Default 1 Description Parameter defines the initial EGPRS coding Schema used at the

beginning of a TBF for RLC acknowledged mode to be used in the extended coverage area of an extended cell.

DN0933393 63


Create BTS

Id:0900d80580646c17

5.62 initMcsExtUnackMode

5.63 interferenceAveragingProcessAverPeriod

Obj BTS M,O,N,internal M Val

Full Name Initial MCS For Ext Area Unacknowledged Mode Type Number Range 1...9, step 1 Internal Value gui_value Default 1 Description Parameter defines the initial EGPRS coding scheme at the

beginning of a TBF to be used for RLC unack mode in the extended coverage area of an extended cell.


Obj BTS M,O,N,internal mapped Val

Full Name Averaging Period Type Number Range 1...32, step 1 Internal Value gui_value Default 6 Description Defines the number of SACCH multiframes over

which the averaging of the interference level in the unallocated time slots is performed

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field averaging period in [BTS] INTAVEPR

64DN0933393


Id:0900d80580646c17

Create BTS

5.64 interferenceAveragingProcessBoundary0



Obj BTS M,O,N,internal mapped Val Ful l Name Interference Averaging Boundary 0 Type Enumeration Range -110 dBm. Fixed boundary (0) Internal Value gui_value Default -110 dBm. Fixed boundary (0) Description Interference Averaging Process boundary limit 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

Obj BTS M,O,N,internal mapped Val Ful l Name Interference Averaging Boundary 1 Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -105 dBm Description Interference Averaging Process boundary limit 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val Field threshold boundary 1 in [BTS] INTAVEPR

Obj BTS M,O,N,internal Mapped Val Ful l Name Interference Averaging Boundary 2 Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -100 dBm Description Interference Averaging Process boundary limit 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val Field threshold boundary 2 in [BTS] INTAVEPR

DN0933393 65


Create BTS

Id:0900d80580646c17






Obj BTS M,O,N,internal Mapped Val Ful l Name Interference Averaging Boundary 5 Type Enumeration Range -47 dBm. Fixed boundary (63) Internal Value (gui_value + 110) Default -47 dBm. Fixed boundary (63) Description Interference Averaging Process boundary limit 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 63

66DN0933393


Id:0900d80580646c17

Create BTS

5.70 locationAreaIdLAC

5.71 locationAreaIdMCC

Obj BTS M,O,N,internal M.mapped Val

Full Name LAC Type Number Range 1...65533, step 1 Internal Value gui_value Default Description Location Area Code 3Gpp Multip 1 Modification Requires object locking Modified All BTSs of the segment must be in a LOCKED state and the GPRS is

disabled. onCreate Mandatory Val Field LAC in [BTS] CELLGLID

Obj BTS M,O,N,internal M.mapped Val

Full Name MCC Type String Range 3 characters Internal Value gui_value Default Description Mobile Country Code of PLMN where location area belongs. 3Gpp Multip 1 Modification Requires object locking Modified All BTSs of the segment must be in a LOCKED state and the GPRS

is disabled. onCreate Mandatory Val Field MCC [BTS] CELLGLID

DN0933393 67


Create BTS

Id:0900d80580646c17

5.72 locationAreaIdMNC

5.73 maxNumberOfRepetition

Obj BTS M,O,N,internal M.mapped Val

Full Name MNC Type String Range 2...3 characters Internal Value gui_value Default Description Mobile Network Code of PLMN where location area belongs. 3Gpp Multip 1 Modification Requires object locking Modified All BTSs of the segment must be in a LOCKED state and the GPRS

is disabled. onCreate Mandatory Val Field MNC [BTS] CELLGLID

Obj BTS M,O,N,internal Mapped Val

Ful l Name Max Number Of R epetition Type Number Range 5...35, step 1 Internal Value gui_value Default 5 Description Defines the maximum number of repetitions of the PHYSICAL

INFO message during a handover that the transceiver can perform

3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 5 + (([BTS] NY1-1) / (253 / 30))

68DN0933393


Id:0900d80580646c17

Create BTS

5.74 msMaxDistInCallSetup

5.75 msTxPwrMaxCCH

Obj BTS M,O,N,internal M Val

Full Name MS Max Distance In Call Setup Type Number Range 0...255 *550m, step 1 *550m Internal Value gui_value Default 255 *550m Description Defines the maximum distance between the BTS and the MS in

call setup 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 255 *550

Obj BTS M,O,N,internal Mapped Val

Full Name MS Tx Pwr Max CCH Type Number Range 5...39 dBm, step 2 dBm Internal Value (gui_value - 43) / -2 Default 33 dBm Description Defines the maximum transmission power an MS may use when

accessing a CCH in the cell. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val {[5 + (([BTS] MSTXPMAXCH * 17) / 31) *2] – 42} / -2

DN0933393 69


Create BTS

Id:0900d80580646c17

5.76 msTxPwrMaxCCH1x00

5.77 msTxPwrMaxGSM

Obj BTS M,O,N,internal Mapped Val

Ful l Name MS Tx Pwr Max CCH 1x00 Type Number Range 0...36 dBm, step 2 dBm Internal Value gui_value Default 30 dBm Description W ith this parameter you define the maximum transmission power

an MS may use when accessing a C CH in the cell for GSM 1800/1900 bands.

3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val ([BTS] MSTXPMAXCH / (31 / 18)) * 2

Obj BTS M,O,N,internal Mapped Val

Ful l Name MS Tx Pwr Max GSM Type Number Range 5...39 dBm, step 2 dBm Internal Value (gui_value - 43) / -2 Default 33 dBm Description The attribute defines max MS transmitting power in cell for GSM 800

and GSM 900 bands. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [BTS] MSTXPMAXGSM (1:1 mapping)

70DN0933393


Id:0900d80580646c17

Create BTS

5.78 msTxPwrMaxGSM1x00

5.79 noOfMFramesBetweenPaging

O b j B T S M ,O ,N ,in tern a l M a p p e d V a l

F ul l N a m e M S Tx P w r M a x G S M 1 x0 0 T yp e N u m be r R a n g e 0 ...3 6 d Bm , s te p 2 d B m In te rn a l V a lu e G SM 1 8 00 :

0..3 0 d Bm : 0 ..1 5 (U I va lu e - 3 0 ) /-2 32 d B m : 3 1 34 d B m : 3 0 36 d B m : 2 9 G SM 1 9 00 : 0..3 0 d Bm : 0 ..1 5 (U I va lu e - 3 0 ) /-2 32 d B m : 3 1 33 d B m : 3 0

D e fa u lt 3 0 d B m D e scr ip tio n Th e a ttri bu te d e fin es m a x M S tra ns m ittin g p o w e r in ce ll fo r G S M

1 80 0 /1 9 0 0 b a n d 3 G p p M u ltip 1 M o di fica tion O n -L in e M o di fie d o n C re ate O p tio na l V a l [BT S ] M S T XP M A X D C S / [B T S ] M ST X P M A XP C S (1 :1

m a p p in g )

Obj BTS M,O,N,internal O Val

Full Name Number Of Multiframes Type Number Range 2...9, step 1 Internal Value gui_value Default 4 Description Defines the number of multiframes between two transmissions of

the same paging message to the MSs of the same paging group 3Gpp Multip 1 Modification Requires object locking Modified All BTSs of the segment must be in a LOCKED state onCreate optional Val [BTS] NFRAMEPG

DN0933393 71


Create BTS

Id:0900d80580646c17

5.80 nbrOfSlotsSpreadTrans

5.81 noOfBlocksForAccessGrant

Obj BTS M,O,N,internal O Val

Ful l Name Number Of S lots Spread Trans Type Enumeration Range 3 (0), 4 (1), 5 (2), 6 (3), 7 (4), 8 (5), 9 (6), 10 (7), 11 (8), 12 (9), 14

(10), 16 (11), 20 (12), 25 (13), 32 (14), 50 (15) Internal Value the value ins ide braces above Default 10 (7) Description Defines the number of TDMA frames over w hich retransmission is

spread on the R ACH (random access channel) 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [BTS] NSLOTST

Obj BTS M,O,N,internal O Val

Ful l Name N umber Of B locks For Access Grant Msg Type N umber Range 0...7, step 1 Internal Value gui_value Default 1 Description D efines the number of blocks reserved for access grant

messages from the C CCH during the 51 TDMA frame (a multiframe)

3Gpp Multip 1 Modification R equires object lock ing Modified A ll BTSs of the segment mus t be in a LOC KED state onCreate optional Val [BTS] NBLKAC GR

72DN0933393


Id:0900d80580646c17

Create BTS

5.82 nonBCCHLayerOffset

5.83 pcuCsHopping

Obj BTS M,O,N,internal Mapped Val

Full Name Non BCCH Layer Offset Type Number Range -40...40, step 1 Internal Value gui_value Default 0 Description The attribute defines an offset margin, which is used when

evaluating the signal level of the non BCCH layer. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val -40 + ([PWRC] ADDPATHLDBC / (40 / 80))

Obj BTS M,O,N,internal M Val

Full Name Coding Scheme Hop Type Enumeration Range Link Adaptation used (0), CS-1 used (1), CS-2 used (2) Internal Value gui_value Default Link Adaptation used (0) Description Attribute indicates the selection of Coding Scheme in RLC (Radio Link

Control) Acknowledged mode in case frequency hopping is used. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 0

DN0933393 73


Create BTS

Id:0900d80580646c17

5.84 pcuCsNonHopping

5.85 pcuDlBlerCpHopping

Obj BTS M,O,N,internal M Val

Full Name Coding Scheme No Hop Type Enumeration Range Link Adaptation used (0), CS-1 used (1), CS-2 used (2) Internal Value gui_value Default CS-2 used (2) Description Attribute indicates selection of Coding Scheme in RLC Acknowledged

mode in case of no Frequency Hopping. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 2

O bj BTS M ,O ,N,in ternal M V al

Ful l Name DL BLE R Cros spoint For CS Selection Hop Type Num ber Range 0...100 % , step 1 % Interna l Va lue gui_value Default 0 ,2 Description Attr ibute ind icates the RLC BLER (b lock error ra te in un its o f percent)

for C S-1 c hannel cod ing. A t th is poin t CS -1 and CS-2 g ive the sam e effec tive b it rate and Coding Schem e selection criteria in RLC Ack nowledged mode for downlink TBFs changes.

3Gpp M ultip 1 M odi fication O n-Line M odi fied onCreate optiona l Val 20

74DN0933393


Id:0900d80580646c17

Create BTS

5.86 pcuDlBlerCpNonHop

5.87 pcuDlLaRiskLevel

O bj B TS M ,O ,N,in ternal M Val

Ful l Name DL B LE R Crosspoint For CS Selection No Hop Type Num ber Range 0...100 % , step 1 % Interna l Va lue gui_value Default 0 ,9 Description A ttribute indicates the RLC BLE R (block error rate in un its of percent)

for CS-1 channel cod ing. At this point CS -1 and CS-2 g ive the sam e effective b it rate and Coding Schem e se lection criteria in R LC A cknow ledged m ode for dow nl ink TB Fs changes.

3Gpp M ultip 1 M odi fication On-Line M odi fied onCreate optional Val 90

Obj BTS M,O,N,internal M Val

Full Name DL adaption probability threshold Type Number Range 0...50 %, step 1 % Internal Value gui_value Default 0,2 Description Attribute defines allowed probability (%) to make a wrong decision in

downlink adaptation. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 20

DN0933393 75


Create BTS

Id:0900d80580646c17

5.88 pcuUlBlerCpHopping

5.89 pcuUlBlerCpNonHop

O bj BTS M ,O ,N,in ternal M V al

Ful l Name UL BLE R Crosspoint For C S Selection Hop Type Num ber Range 0...100 % , s tep 1 % Interna l Va lue gui_value Default 0 ,24 Description Attr ibute indicates the RLC BLE R (b lock error ra te in un its o f percent)

for C S-1 channel cod ing. A t th is poin t CS -1 and CS-2 g ive the sam e effective bi t rate and Coding Schem e selec tion criteria in R LC Ac know ledged m ode for up link TBFs changes.

3Gpp M ultip 1 M odi fication O n-L ine M odi fied onCreate optional Val 24

O bj B TS M ,O ,N,in ternal M Val

Ful l Name U L B LER Crosspoin t For CS Selection No Hop Type N um ber Range 0...100 % , step 1 % Interna l Va lue gu i_value Default 0,9 Description A ttribute ind icates the RLC B LE R (b lock error rate in units of percent)

for CS-1 channel coding. At th is point C S-1 and CS-2 g ive the sam e effective b it ra te and C oding Sc hem e selection criteria in RLC A cknowledged m ode for upl ink TB Fs changes.

76DN0933393


Id:0900d80580646c17

Create BTS

5.90 pcuUlLaRiskLevel

5.91 qSearchP

Obj BTS M,O,N,internal M Val

Full Name UL Adaption Probability Threshold Type Number Range 0...50 %, step 1 % Internal Value gui_value Default 0,1 Description Attribute defines allowed probability (%) to make a wrong decis ion in

uplink adaptation. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 10

O bj B TS M ,O ,N,in ternal M Val

F ul l Name G P RS T hreshold T o S earch UT RAN Cells T ype E num eration Range -98 dBm (0), -94 dBm (1), -90 dB m (2), -86 dBm (3), -82 dBm (4), -78 dB m

(RLA _P below ) (5), -74 dBm (RLA _P below) (6), In fin ity (a lways) (7), -78 dBm (RLA _P above) (8), -74 dBm (RLA_P above) (9), -70 dBm (10), -66 dBm (11), -62 dBm (12), -58 dB m (13), -54 dB m (14), In fin ity (never) (15)

In terna l Va lue gu i_value Defau lt Descrip tion D efines the threshold for GPR S capable dua l m ode m obiles to search for and to

m easure UTRA N neighbour c el ls in troduced in 3G Cell R eselection list when a running average of RLA_C of the serving ce ll is be low or above the threshold.

3Gpp Q search_P M ultip 1 M odi fication O n-L ine M odi fied onCreate O ptiona l Val [B TS ]. QS RHI:

U MD B98 98 dB m (0) U MD B94 -94 dBm (1) U MD B90 -90 dBm (2) U MD B86 -86 dBm (3) U MD B82 -82 dBm (4) U MD B78 -78 dBm (RLA_P below) (5) U MD B74 -74 dBm (RLA_P below) (6) A LW AY S In fini ty (a lways) (7) O M DB 78 -78 dBm (RLA_P above) (8) O M DB 74 -74 dBm (RLA_P above) (9) O M DB 70 -70 dBm (10) O M DB 66 -66 dBm (11) O M DB 62 -62 dBm (12) O M DB 58 -58 dBm (13) O M DB 54 -54 dBm (14) N EVE R In fini ty (never) (15)

DN0933393 77


Create BTS

Id:0900d80580646c17

5.92 raReselectHysteresis

5.93 rac

Obj BTS M,O,N,internal M Val

Full Name RA Reselect Hysteresis Type Number Range 0...14 dB, step 2 dB Internal Value gui_value / 2 Default 4 dB Description Attribute defines additional hysteresis applied in both STANDBY and

READY states for selecting a cell in a different routing area. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 2

Obj BTS M,O,N,internal M Val Ful l Name RAC Type Number Range 0...255, step 1 Internal Value gui_value Default 255 Description Routing Area Code 3Gpp Multip 1 Modification On-Line Modified Only when the GPRS is disabledonCreate Optional Val 255

78DN0933393


Id:0900d80580646c17

Create BTS

5.94 radiusExtension

5.95 segmentId

Obj BTS M,O,N,internal M Val Full Name Radius Extension Type Number Range 0...67 km, step 1 km Internal Value gui_value Default 0 km Description Defines the radius extension of an extended cell. 3Gpp Multip 1 Modification Requires object locking Modified When the BTS is locked. onCreate optional Val 0

(radiusExtension (BTS-new))

Obj BTS M,O,N,internal mapped Val

Ful l Name Segment ID Type N umber Range 1...3000, step 1 Internal Value gui_value Default Description Multi BCF Segment number (Segment ID) of the Master BTS. If Multi BCF is not

used, it is the same as BTS ID. This parameter should not have any value in the R AC Templates.

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val " segmentId " info in control file (related BTS sourceObjec t)

DN0933393 79


Create BTS

Id:0900d80580646c17

5.96 segmentName

5.97 superRadiusExtension

Obj BTS M,O,N,internal O Val

Full Name Segment Name Type String Range 1...15 characters Internal Value gui_value Default Description With this parameter you identify the segment by its name.

used to manage BTS id mapping as described in Error! Reference source not found. Error! Reference source not found.

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val " segmentName " info in control file (related BTS sourceObject)

example: “3000BRCNxy”, where: • ‘3000’ segment name (as normaly intended in BSS) • ‘BRCN’ fixed string to indicate cellNumber as needed by BSxx • ‘xy’ “cellNumber” (HMO), 00..11

O bj B TS M ,O ,N,in ternal M Val

Ful l Name S uper Radius Extension Type Num ber Range 36...70 km , step 1 km Interna l Va lue gu i_value Default 0 km Description W ith th is parameter you define the d istance (km ) of inner edge of 35

km wide super extended area from BTS. Value 0 means that s uper extended area is not in use.

3Gpp M ultip 1 M odi fication Requires object locking M odi fied W hen the BTS is locked. onCreate optiona l Val 0

superRadiusE xtension (B TS -new) /

80DN0933393


Id:0900d80580646c17

Create BTS

5.98 throughputFactor_cs1cs4dlcs

5.99 throughputFactor_cs1cs4ulcs

O bj B TS M ,O ,N,in ternal M Val

Ful l Name B TS Downlink Throughput Fac tor For CS 1-CS 4 Type Num ber Range 0...100 kb it/s, step 1 kbi t/s Interna l Va lue gu i_value Default 12 kb it/s Description W ith th is parameter you indicate typ ical throughput per

tim eslo t in the B TS , depending on the d irection and (M )CS. The param eter is used w hen com paring the TSL capacities between di fferent B TSs.


O bj B TS M ,O ,N,in ternal M Val

Ful l Name B TS Uplink Throughput Factor For CS 1-CS 4 Type Num ber Range 0...100 kb it/s, step 1 kbi t/s Interna l Va lue gu i_value Default 12 kb it/s Description W ith th is parameter you indicate typ ical throughput per

tim eslo t in the B TS , depending on the d irection and (M )CS. The param eter is used w hen com paring the TSL capacities between di fferent B TSs.

DN0933393 81


Create BTS

Id:0900d80580646c17

5.100 throughputFactor_mcs1mcs4ulcs

5.101 throughputFactor_mcs1mcs9dlcs

O bj B TS M ,O ,N,in ternal M V al

Ful l Name B TS Uplink Throughput Fac tor For M CS1-M CS4 Type N um ber Range 0...100, step 1 Interna l Va lue gu i_va lue Default 16 Description W ith th is parameter you ind icate typ ical throughput per

tim eslo t in the B TS , depending on the d irection and (M )C S. The param eter is us ed when comparing the TSL capacities between different B TS s.

3Gpp M ultip 1 M odi fication On-Line M odi fied onCreate optiona l Val 16

O bj B TS M ,O ,N,in ternal M V al

Ful l Name B TS Downlink Throughput Fac tor For M CS1-M CS9 Type N um ber Range 0...100 kbit/s, step 1 kb it/s Interna l Va lue gu i_va lue Default 30 kb it/s Description W ith th is parameter you ind icate typ ical throughput per

tim eslo t in the B TS , depending on the d irection and (M )C S. The param eter is us ed when comparing the TSL capacities between different B TS s.

3Gpp M ultip 1 M odi fication On-Line M odi fied onCreate optiona l Val 30

82DN0933393


Id:0900d80580646c17

Create BTS

5.102 throughputFactor_mcs1mcs9ulcs

O bj B TS M ,O ,N,in ternal M V al

Ful l Name B TS Uplink Throughput Fac tor For M CS1-M CS9 Type N um ber Range 0...100 kbit/s, step 1 kbit/s Interna l Va lue gui_value Default 30 kbit/s Description W ith th is parameter you indicate typ ical throughput per

tim eslot in the B TS , depending on the d irection and (M )C S. The param eter is us ed when comparing the TSL capacities between different B TS s.

3Gpp M ultip 1 M odi fication On-Line M odi fied onCreate optional Val 30

DN0933393 83


Create TRX

Id:0900d80580646417

6 Create TRX

The distinguished name for the TRX (distName value) is not derived from the TRX relative value in the BR configuration script. This value must be explicitly set in the control file, for each TRX under migration.

When administering the BTSplus with the eBSC/BSC1, up to 48 TRXs can be created for a single BTSM, while after migration the maximum number of TRXs per BCF cannot exceed 32. In configurations where the maximum number of TRXs per BTSM should be greater than 32, the exporter tool can not decide which TRX must be dropped. The re-adjustment to a proper number of TRXs can be performed before migration or after-wards by postprocessing the migration tool output. For details of the tool strategy regarding the Abis 16 kbit/s timeslots allocation, refer to “Packet migration”.

Create TRX Example from Real NetAct Configuration script managedObject class="TRX" operation="create" version="S14.1" distName="BSC-12345/BCF-45/BTS-198/TRX-1">

<defaults name="ESTemplate"/> 124 7 2 TRX EXS11 3 133 133 133 133 133 133 133 133 1 1 1 1 2 2 2 2 3 0 0 0 0 0 0 45 1

/managedObject>

84DN0933393


Id:0900d80580646417

Create TRX

6.1 bbUnitSupportsEdgeOnly a gettable parameter.

BR range channel Combination Abisvalue

BSS CH0 BSS CH1 BSS CH2-3 BSS CH4-7

TCHFUL TCH/F+FACCH/F+SACCH/TF 0 TCHF (0) TCHF (0) TCHF (0) TCHF (0)

SDCCH SDCCH/8+SACCH/C8 3 SDCCH (3) SDCCH (3) SDCCH (3) SDCCH (3)

MAINBCCH FCCH+SCH+BCCH+CCCH 4 MBCCH (4) Not allowed Not allowed Not allowed

MBCCHC FCCH+SCH+BCCH+CCCH+SDCCH/3 (0..2)+SACCH/C4 (0..3)

5 MBCCH (5) Not allowed Not allowed Not allowed

CCCH BCCH+CCCH 6

SCBCH SDCCH/8(0..7)+SACCH/C8(0..7)+CBCH

7 Not allowed SDCCB (8) SDCCB (8) Not allowed

BCBCH FCCH+SCH+BCCH+CCCH+SDCCH/4+SACCH/4+CBCH

8 MBCCH (7) Not allowed Not allowed Not allowed

TCH_HLF • TCH/H(01)+FACCH/H(01)+SACCH/TH(01) or

• TCH/F+FACCH/F+SACCH/TF

9 TCHD (2) TCHD (2) TCHD (2) TCHD (2)

TCHSD • TCH/H(01) + FACCH/H(01) + SACCH/TH(01) or

• TCH/F+FACCH/F+SACCH/F • SDCCH/8+SACCH/8

10 If (CHPOOL-TYP=TCH-POOL or TCHSD){TCHD (2)}else SDCCH (3)

If (CHPOOL-TYP=TCH-POOL or TCHSD){TCHD (2)}else SDCCH (3)



11

12

13 Not allowed Not allowed Not allowed Not allowed

14 EGTCH (14) EGTCH (14) EGTCH (14) EGTCH (14)

15 Not allowed Not allowed LRTCH (15) LRTCH (15)

Table 1 Mapping for BR [CHAN] CHTYPE to channel<n>Type

DN0933393 85


Create TRX

Id:0900d80580646417

6.2 channel0Maio

6.3 channel0Pcm

Obj TRX M,O,N,internal Mapped Val Full Name Channel 0 Maio Type Number Range 0...63, step 1 Internal Value gui_value Default Description Mobile allocation index offset (MAIO). 3Gpp Multip 1 Modification Not modifiable Modified onCreate Optional Val [TRX] / [CHAN] MAIO:

take MAIO from TRX but if it is NULL then from 1st channel of that TRX

Obj TRX M,O,N,internal M Val

Full Name Channel 0 PCM Type Number Range 1...3391, step 1 Internal Value gui_value Default Description Defines the Abis speech channel allocation ET-PCM number of TRX.

Modifiable when provisioning plan with CM Operations Manager and not selecting Use File Based Activation Method for S12 BSC -option. Not modifiable when using send to network in CM Editor.

3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val Derived from BR available STSLB pool (flexible Abis allocation) (e.g.

CREATE SUBTSLB: NAME=PCMB:6/TSLB:1/SUBTSLB:1,ASSLAPD=BTSM:35/LPDLM:1;) and from control file for PCM mapping (related BTSM sourceObject)

86DN0933393


Id:0900d80580646417

Create TRX

6.4 channel0Subslot

6.5 channel0Tsl

Obj TRX M,O,N,internal M Val

Full Name Channel 0 Subslot Type Number Range 0...3, step 1 Internal Value gui_value Default 0 Description With this parameter you define the Abis speech channel allocation of the

TRX. Parameter defines the radio time slots to a subslot. 3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val Derived from BR available STSLB pool (flexible Abis allocation) (e.g.

CREATE SUBTSLB: NAME=PCMB:6/TSLB:1/SUBTSLB:1,ASSLAPD=BTSM:35/LPDLM:1;)

Obj TRX M,O,N,internal M Val

Ful l Name Channel 0 TSL Type Number Range 1...31, step 1 Internal Value gui_value Default Description Defines the Abis speech channel allocation times lot number of TR X. Modifiable

when provisioning plan with CM Operations Manager and not selecting Us e File Based Activation Method for S12 BSC -option. Not modifiable when using send to network in CM Editor.

3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val Derived from BR available STSLB pool (flexible Abis allocation) (e.g. CR EATE

SUBTSLB: NAME=PCMB:6/TSLB:1/SUBTSLB:1,ASSLAPD=BTSM:35/LPDLM:1;)

DN0933393 87


Create TRX

Id:0900d80580646417

6.6 channel0Type

6.7 channel1Maio

Obj TRX M,O,N,internal M.mapped Val

Full Name Channel 0 Type Type Enumeration Range TCHF (0), TCHH (1), TCHD (2), SDCCH (3), MBCCH (4), MBCCHC (5),

MBCCB (7), Not allowed in CH0 (8), Not In Use (9), ERACH (10), Not allowed in CH0 (13), EGTCH (14), Not allowed in CH0 (15)

Internal Value gui_value Default TCHF (0) Description With this parameter you define the logical channel combination that has to

be mapped onto the basic physical channel. 3Gpp Multip 1 Modification Requires object locking Modified When TRX is locked onCreate Mandatory Val [CHAN] CHTYPE (see related Table)

88DN0933393


Id:0900d80580646417

Create TRX

6.8 channel1Pcm

6.9 channel1Subslot










DN0933393 89


Create TRX

Id:0900d80580646417

6.10 channel1Tsl

6.11 channel1Type


Full Name Channel 1 TSL Type Number Range 1...31, step 1 Internal Value gui_value Default Description Defines the Abis speech channel allocation timeslot number of TRX. Modifiable

when provisioning plan with CM Operations Manager and not selecting Use File Based Activation Method for S12 BSC -option. Not modifiable when using send to network in CM Editor.

3Gpp Multip 1 Modification Requires object locking Modified onCreate Mandatory Val Derived from BR available STSLB pool (flexible Abis allocation) (e.g. CREATE



Full Name Channel 1 Type Type Enumeration Range TCHF (0), TCHH (1), TCHD (2), SDCCH (3), Not allowed in CH1 (4), Not

allowed in CH1 (5), Not allowed in CH1 (7), SDCCB (8), Not In Use (9), Not allowed in CH1 (10), Not allowed in CH1 (13), EGTCH (14), Not allowed in CH1 (15)


be mapped onto the basic physical channel. 3Gpp Multip 1 Modification Requires object locking Modified When TRX is locked onCreate mandatory Val [CHAN] CHTYPE (see related Table)

90DN0933393


Id:0900d80580646417

Create TRX

6.12 channel2Maio

6.13 channel2Pcm

Obj TRX M,O,N,internal mapped Val Full Name Channel 2 Maio Type Number Range 0...63, step 1 Internal Value gui_value Default Description Mobile allocation index offset (MAIO). 3Gpp Multip 1 Modification Not modifiable Modified onCreate optional Val [TRX] / [CHAN] MAIO:





3Gpp Multip 1 Modification Not modifiable Modified onCreate mandatory Val Derived from BR available STSLB pool (flexible Abis allocation) (e.g.

DN0933393 91


Create TRX

Id:0900d80580646417

6.14 channel2Subslot

6.15 channel2Tsl



TRX. Parameter defines the radio time slots to a subslot. 3Gpp Multip 1 Modification Not modifiable Modified onCreate mandatory Val Derived from BR available STSLB pool (flexible Abis allocation) (e.g.





3Gpp Multip 1 Modification Not modifiable Modified onCreate mandatory Val Derived from BR available STSLB pool (flexible Abis allocation) (e.g. CREATE


92DN0933393


Id:0900d80580646417

Create TRX

6.16 channel2Type

6.17 channel3Maio



allowed in CH2 (5), Not allowed in CH2 (7), SDCCB (8), Not In Use (9), Not allowed in CH2 (10), Not allowed in CH2 (13), EGTCH (14), LRTCH (15)





DN0933393 93


Create TRX

Id:0900d80580646417

6.18 channel3Pcm











94DN0933393


Id:0900d80580646417

Create TRX

6.20 channel3Tsl

6.21 channel3Type








allowed in CH3 (5), Not allowed in CH3 (7), SDCCB (8), Not In Use (9), Not allowed in CH3 (10), Not allowed in CH3 (13), EGTCH (14), LRTCH (15)



DN0933393 95


Create TRX

Id:0900d80580646417

6.22 channel4Maio

6.23 channel4Pcm








96DN0933393


Id:0900d80580646417

Create TRX


6.25 channel4Tsl








3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val Derived from BR available STSLB pool (flexible Abis allocation) (e.g. CREATE


DN0933393 97


Create TRX

Id:0900d80580646417

6.26 channel4Type

6.27 channel5Maio



allowed in CH4 (5), Not al lowed in CH4 (7), Not allowed in CH4 (8), Not allowed in CH4 (9), Not al lowed in CH4 (10), Not allowed in CH4 (13), EGTCH (14), LRTCH (15)


be mapped onto the basic physical channel. 3Gpp Multip 1 Modification Requires object locking Modified When TRX is locked onCreate Mandatory Val [CHAN] CHTYPE (see related Table)



98DN0933393


Id:0900d80580646417

Create TRX

6.28 channel5Pcm











DN0933393 99


Create TRX

Id:0900d80580646417

6.30 channel5Tsl

6.31 channel5Type











100DN0933393


Id:0900d80580646417

Create TRX

6.32 channel6Maio

6.33 channel6Pcm








DN0933393 101


Create TRX

Id:0900d80580646417


6.35 channel6Tsl










102DN0933393


Id:0900d80580646417

Create TRX

6.36 channel6Type

6.37 channel7Maio








DN0933393 103


Create TRX

Id:0900d80580646417

6.38 channel7Pcm











104DN0933393


Id:0900d80580646417

Create TRX

6.40 channel7Tsl

6.41 channel7Type











DN0933393 105


Create TRX

Id:0900d80580646417

6.42 circuitTelecom

6.43 eTrxInd

Obj TRX M,O,N,internal M Val Full Name Circuit Telecom Type Number Range 0...255, step 1 Internal Value gui_value Default Description Pcm-tsl(s) of a traffic channel in Abis interface (SMUX-pcm) 3Gpp Multip 1 Modification Not modifiable Modified onCreate optional Val from control file for PCM mapping (related BTSM sourceObject)

Obj TRX M,O,N,internal Mapped Val

Full Name E-TRX Type Type Enumeration Range The TRX is a normal TRX (N) (0), The TRX is an extended TRX (E) (1), The TRX

is an super extended TRX (S) (2) Internal Value gui_value Default The TRX is a normal TRX (N) (0) Description Defines whether the TRX is working as an extended TRX (E-TRX) or a normal

TRX (N-TRX) or super extended TRX (S-TRX) 3Gpp Multip 1 Modification Requires object locking Modified When the TRX is locked. onCreate Optional Val 0

eTrxInd (new in Abis)

106DN0933393


Id:0900d80580646417

Create TRX

6.44 initialFrequency

6.45 lapdLinkName

Obj TRX M,O,N,internal M Val Full Name Frequency Type Number Range 0...1023, step 1 Internal Value gui_value Default Description With this parameter you assign the ARFCN

(absolute radio frequency number) to the transceiver. Value range

GSM 800 128..251, GSM 900 0..124 and 975..1023, GSM 1800 512..885, GSM 1900 512..810.

3Gpp Multip 1 Modification Requires object locking Modified When TRX is locked onCreate mandatory Val use the value of [BTS] (BCCHFREQ | CALLFnn)

depending of the setting of ([TRX] TRXFREQ)

Obj TRX M,O,N,internal M Val

Full Name LAPD Link Name Type String Range 1...5 characters Internal Value gui_value Default Description Name of the LAPD Link. Modifiable when provisioning plan with CM

Operations Manager or command line interface and not having Use File Based Activation Method for S12 BSC -option selected in GSM Options. Unmodifiable when using send to Network in CM Editor

3Gpp Multip 1 Modification Requires object locking Modified onCreate Mandatory Val “lapdLinkName" info in control file (related TRX sourceObject)

DN0933393 107


Create TRX

Id:0900d80580646417

6.46 trxFrequencyType

6.47 tsc

Obj TRX M,O,N,internal Mapped Val

Full Name TRX Frequency Type Type Number Range 0...16, step 1 Internal Value gui_value Default 0 Description With this parameter you define the type of the TRX's radio frequency

used with the optional Intelligent Underlay-Overlay feature. 3Gpp Multip 1 Modification Requires object locking Modified If TRX is BCCH TRX and HOP=BB, BTS must be locked. If TRX is

BCCH TRX and UHOP=BB, BTS must be locked. In other cases, TRX must be locked. The modification requires BTS locking if the frequency layer of the TRX is RF hopping and the modification is made from regular to super-reuse frequency layer or vice versa.

onCreate Optional Val 1 in case of a TRX belonging to the INNER AREA, 0 otherwise.

Obj TRX M,O,N,internal M.mapped Val Full Name TSC Type Number Range 0...7, step 1 Internal Value gui_value Default Description Defines the training sequence code (TSC) of a carrier. 3Gpp Multip 1 Modification Requires object locking Modified When TRX is locked onCreate Mandatory Val [CHAN] TSC (trainingSequenceCode)

take TSC from the first channel; if TSC = NULL take bcc

108DN0933393


Id:0900d805806430bc

Create MAL

7 Create MAL

This chapter has only been added for documentation purposes. Hopping laws for the Nokia Siemens Networks GSM/EDGE BSS product line have to be added to the gener-ated NetAct script, as the frequency hopping laws of the eBSC/BSC1 are not migrated. For more information, refer to “Frequency hopping”.

7.1 frequency

Create MAL Example from Real NetAct Configuration script managedObject class="MAL" distName="PLMN-PLMN/BSC-54040/MAL-1" operation="update">

<list name="frequency"> 10 20 30 41 52 53 </list> 0

/managedObject>

Obj MAL M,O,N,internal M Val Full Name Frequency Type Number Range 0...1023, step 1 Internal Value gui_value Default Description Frequencies of the mobile allocation frequency list 3Gpp Multip 63 Modification On-Line Modified When BTS is locked, if used in a RF hopping BTS onCreate Optional Val [FHSY] [CFHSY] MOBALLOC / CMOBALLOC

DN0933393 109


Create MAL

Id:0900d805806430bc


Obj MAL M,O,N,internal M Val Full Name Type Of Mobile Allocation Frequency List Type Enumeration Range GSM 900 (0), GSM 1800 (1), GSM 1900 (2), GSM 800 (5)Internal Value gui_value Default Description Frequency Band used for the MAL 3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val [BTS} SYSID

110DN0933393


Id:0900d805806430b4

Create BAL

8 Create BAL

This chapter has only been added for documentation purposes. Hopping laws for the Nokia Siemens Networks GSM/EDGE BSS product line have to be added to the gener-ated NetAct script, as the frequency hopping laws of the eBSC/BSC1 are not migrated. For more information, refer to “Frequency hopping”.

8.1 frequency

Create BAL Example from Real NetAct Configuration script managedObject class="MAL" distName="PLMN-PLMN/BSC-54040/BAL-1" operation="update">

<list name="frequency"> 10 20 30 41 52 </list> 0

/managedObject>

Obj BAL M,O,N,internal M Val

Full Name Frequency Type Number Range 0...1023, step 1 Internal Value gui_value Default Description With this parameter you define the frequencies of the BCCH frequency list. If

either any of the Common BCCH are used or ISHO Support feature is used, the max is 31. If any of the Common BCCH feature and also ISHO Support feature is used, the max is 30.

3Gpp Multip 32 Modification On-Line Modified onCreate Optional Val [FHSY] [CFHSY] MOBALLOC / CMOBALLOC

DN0933393 111


Create BAL

Id:0900d805806430b4


Obj BAL M,O,N,internal M Val

Full Name Type Of BCCH Frequency List Type Enumeration Range GSM 900 (0), GSM 1800 (1), GSM 1900 (2), Multi Band (3), GSM

800 (5) Internal Value gui_value Default Description Defines the type of the BCCH frequency l ist 3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val [BTS} SYSID

112DN0933393


Id:0900d805805c445d

Create POC

9 Create POC

9.1 alpha

9.2 bepPeriod

Create POC Example from Real NetAct Configuration script managedObject class="POC" operation="create" version="S14.1" distName="BSC-12345/BCF-45/BTS-199/POC-1">

<defaults name="ESTemplate"/> 0 0 8

/managedObject>

Obj POC M,O,N,internal M Val Full Name Binary Representation ALPHA Type Number Range 0...10, step 1 Internal Value gui_value Default 7 Description The binary representation of the parameter for MS output power control. 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 7

Obj POC M,O,N,internal M Val

Full Name Bit Error Probability Filter Averaging Period Type Enumeration Range 1 (0), 2 (1), 3 (2), 4 (3), 5 (4), 7 (5), 10 (6), 12 (7), 15 (8), 20 (9), 25 (10) Internal Value gui_value Default 10 (6) Description Attribute defines the bit error probability (BEP) filter averaging period for

EGPRS channel quality measurementsRange 1,2,3,4,5,7,10,12,15,20,25 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 6

DN0933393 113


Create POC

Id:0900d805805c445d

9.3 bsTxPwrMax

Obj POC M,O,N,internal mapped Val

Full Name BS Tx Pwr Max Type Number Range 0...30, step 2 Internal Value gui_value / 2 Default 0 Description Identifies the maximum transmission power of the GSM 800 or GSM 900 BTS

as an attenuation from the peak power of the TRX 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Take the most common used value of [TRX] PWRRED / (9 / 15))

Note: the most common value is related only to the cell the TRX belongs to (in case of concentric or dual band cells, the two areas must be considered as different TRX groups; on bsTxPwrMax must be always mapped the group associated to the band of the BCCH TRX)

114DN0933393


Id:0900d805805c445d

Create POC

9.4 bsTxPwrMax1x00

9.5 bsTxPwrMin

Obj POC M,O,N,internal Mapped Val

Full Name BS TX Pwr Max1x00 Type Number Range 0...30 dB, step 2 dB Internal Value gui_value / 2 Default 0 dB Description Identifies the maximum transmission power of the GSM 1800 or GSM

1900 BTS as an attenuation from the peak power of the TRX 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val Take the most common used value of [TRX] PWRRED / (9 / 15))

Note: the most common value is related only to the cell the TRX belongs to (in case of concentric or dual band cells, the two areas must be considered as different TRX groups; on bsTxPwrMax1x00 must be always mapped the group associated to the band other than the BCCH TRX)

Obj POC M,O,N,internal mapped Val

Full Name BS Tx Pwr Min Type Number Range 0...30 dB, step 2 dB Internal Value gui_value / 2 Default 30 dB Description Identifies the minimum transmission power of the BTS as an attenuation from

the peak power of the TRX 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [PWRC] PCMBSTXPRL

DN0933393 115


Create POC

Id:0900d805805c445d

9.6 bsTxPwrOffset

9.7 enableAla

Obj POC M,O,N,internal mapped Val

Full Name BS TX Pwr Offset Type Number Range 0...30 dB, s tep 2 dB Internal Value gui_value / 2 Default 0 dB Description Identifies attenuation offset for non-BCCH Super-Reuse TRXs of the

segement when FRT is 16 and Handover Support for Coverage Enhancement (HSCE) is active in the segment.

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Value different from 0 only when in case of concentric cells the

bsTxPwrMax and bsTxPwrMax1x00 values are different, (when bsTxPwrOffset must be set as delta value)

Obj POC M,O,N,internal mapped Val

Full Name ALA Enabled Type Enumeration Range automatic link adaptation is disabled (N) (0), automatic link adaptation is

enabled (Y) (1) Internal Value gui_value Default automatic link adaptation is disabled (N) (0) Description With this parameter you switch on and off the automatic link adaptation function

where the channel coding is changed between 14.4 kbit/s and 9.6 kbit/s. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [PWRC] ERUDGR:

• TRUE ? 1 • FALSE? 0

116DN0933393


Id:0900d805805c445d

Create POC

9.8 minIntBetweenAla

9.9 pcALDlWeighting

Obj POC M,O,N,internal mapped Val

Full Name Min Int Between ALA Type Number Range 0...30, step 1 Internal Value gui_value Default 10 Description Defines the time interval between two consecutive automatic link

adaptation procedures where the channel coding is changed between 14.4 kbit/s and 9.6 kbit/s.

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val (Min between ([HAND] TINHRDGR, TINHRUGR)) / (98/30)

Obj POC M,O,N,internal mapped Val

Full Name PC Averaging Lev DL Weighting Type Number Range 1...3, step 1 Internal Value gui_value Default 1 Description The parameter calculates averaged values from signal strength downlink

measurements for the power control process 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field DTX weighting factor of [PWRC] PAVRLEV

DN0933393 117


Create POC

Id:0900d805805c445d

9.10 pcALDlWindowSize

9.11 pcALUlWeighting

Obj POC M,O,N,internal mapped Val

Full Name PC Averaging Lev DL W indow Size Type Number Range 1...32, step 1 Internal Value gui_value Default 4 Description The parameter calculates averaged values from signal strength

downlink measurements for the power control process 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field averaging period of [PWRC] PAVRLEV

Obj POC M,O,N,internal mapped Val

Full Name PC Averaging Lev UL Weighting Type Number Range 1...3, step 1 Internal Value gui_value Default 1 Description The parameter calculates averaged values from signal strength uplink

measurements for the power control process 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field DTX weighting factor of [PWRC] PAVRLEV

118DN0933393


Id:0900d805805c445d

Create POC

9.12 pcALUlWindowSize

9.13 pcAQLDlWeighting

Obj POC M,O,N,internal mapped Val

Full Name PC Averaging Lev UL Window Size Type Number Range 1...32, step 1 Internal Value gui_value Default 4 Description The parameter calculates averaged values from signal s trength uplink

measurements for the power control process 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field averaging period of [PWRC] PAVRLEV

Obj POC M,O,N,internal mapped Val

Full Name PC Averaging Qual DL Weighting Type Number Range 1...3, step 1 Internal Value gui_value Default 1 Description The parameter calculates averaged values from signal strength

downlink measurements for the power control process 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field DTX weighting factor of [PWRC] PAVRQUAL

DN0933393 119


Create POC

Id:0900d805805c445d

9.14 pcAQLDlWindowSize

9.15 pcAQLUlWeighting

Obj POC M,O,N,internal mapped Val

Full Name PC Averaging Qual DL Window Size Type Number Range 1...32, step 1 Internal Value gui_value Default 1 Description The parameter calculates averaged values from signal strength

downlink measurements for the power control process 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field averaging period of [PWRC] PAVRQUAL

Obj POC M,O,N,internal mapped Val

Full Name PC Averaging Qual UL Weighting Type Number Range 1...3, step 1 Internal Value gui_value Default 1 Description The parameter calculates averaged values from signal strength uplink

measurements for the power control process 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field DTX weighting factor of [PWRC] PAVRQUAL

120DN0933393


Id:0900d805805c445d

Create POC

9.16 pcAQLUlWindowSize

9.17 pcControlInterval

Obj POC M,O,N,internal mapped Val

Full Name PC Averaging Qual UL Window Size Type Number Range 1...32, step 1 Internal Value gui_value Default 1 Description The parameter calculates averaged values from signal strength

uplink measurements for the power control process 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field averaging period of [PWRC] PAVRQUAL

Obj POC M,O,N,internal mapped Val

Full Name Power Control Interval Type Number Range 0...31, step 1 Internal Value gui_value Default 2 Description Defines the minimum interval between the changes in the radio

frequency power level 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [PWRC] PCONINT

DN0933393 121


Create POC

Id:0900d805805c445d

9.18 pcIncrStepSize

9.19 pcLTQual144RxQual

O b j PO C M ,O ,N ,in tern a l ma p p e d V a l

F ul l N a me Po w e r Inc r S te p S ize T yp e N u m be r R a n g e 2 ...6 , s te p 2 In te rn a l Va lu e (g u i_ va lu e - 2 ) / 2 D e fa u lt 4 D e scr ip tio n D e fin es th e s te p s ize for in cre a s in g th e tran sm iss io n p o w e r o f th e mo b ile

s ta ti on 3 G p p M u ltip 1 M o di fica tion O n -L in e M o di fie d o n C re ate o ptio n a l Va l [PW R C ] PW R IN C SS :

D B2 --> 2 D B4 --> 4 D B6 --> 6

O b j PO C M ,O ,N ,in tern a l m ap p e d V a l

F ul l N a me PC L o w e r Th re sh o ld s Q ua l1 4 4 R x L e ve l T yp e En u m e ra tio n R a n g e < 0 .2 % (0 ), 0 .2 % - 0 .4 % (1 ), 0 .4 % - 0 .8% (2) , 0 .8 % - 1 .6% (3) , 1 .6 % -

3 .2% (4 ), 3 .2 % - 6 .4 % (5) , 6 .4 % - 1 2.8 % (6 ) , > 1 2 .8% (7) In te rn a l Va lu e g u i_ value D e fa u lt 0 .8% - 1.6 % (3 ) D e scr ip tio n Th e p a ram e te r i s use d fo r c om p a r in g th e a ve ra g e d va lu es o f th e

s ig n a l q ua li ty u p lin k a n d d ow nl ink me a su rem e n ts fo r tr ig g e rin g th e p o w e r co n trol p ro ce d ure fo r 1 4 .4 kb it/s co nn e ctio n s.

3 G p p M u ltip 1 M o di fica tion O n -L in e M o di fie d o n C re ate o p ti on a l Va l M IN [H AN D ] (R D G R D L / R D G R U L / R U G R D L / R U G R U L ) ra n g e : 0 ..

2 0 [d B C /I]) (M IN : w o rst q u a lity ) 0 ,1 7 (6 .8 8 – 7 .0 0 ) 2 7 (6 .7 6 – 6 .8 7 ) 4 7 (6 .3 8 – 6 .7 5 ) 5 6 (6 .1 3 – 6 .3 7 ) 6 6 (5 .8 8 – 6 .1 2 ) 7 6 (5 .6 3 – 5 .8 7 ) 8 6 (5 .1 3 – 5 .6 2 ) 9 5 (4 .8 8 – 5 .1 2 ) 1 0 5 (4 .6 3 – 4 .8 7 ) 1 1 4 (4 .1 3 – 4 .6 2 ) 1 2 4 (3 .8 8 – 4 .1 2 ) 1 3 4 (3 .3 8 – 3 .8 7 ) 1 4 3 (2 .8 8 – 3 .3 7 ) 1 5 3 (2 .6 3 – 2 .8 7 ) 1 6 2 (2 .1 3 – 2 .6 2 ) 1 7 2 (1 .6 3 – 2 .1 2 ) 1 8 1 (1 .1 3 – 1 .6 2 ) 1 9 1 (0 .3 8 – 1 .1 2 ) 2 0 0 (0 .0 0 – 0 .3 7 )

122DN0933393


Id:0900d805805c445d

Create POC

9.20 pcLTQualDlRxQualO bj PO C M ,O ,N,in ternal m apped Val

F ul l Name PC Low er T hresholds Qual D L R x Qual T ype Enum eration Range < 0 .2% (0), 0 .2% - 0 .4% (1), 0 .4% - 0 .8% (2), 0 .8% - 1 .6% (3), 1 .6% -

3 .2% (4), 3 .2% - 6 .4% (5), 6 .4% - 12.8% (6), > 12.8% (7) In terna l Va lue gui_va lue Default 0 .8% - 1 .6% (3) Descrip tion T he parameters compare the averaged va lues of signal quality

downlink m easurem ents for tr iggering the power contro l process 3Gpp M ultip 1 M odi fication O n-L ine M odi fied onCreate optional Val [PW RC] LOW TQ UAD

0,1 7 (6 .88 – 7.00) 2 7 (6 .76 – 6.87) 4 7 (6 .38 – 6.75) 5 6 (6 .13 – 6.37) 6 6 (5 .88 – 6.12) 7 6 (5 .63 – 5.87) 8 6 (5 .13 – 5.62) 9 5 (4 .88 – 5.12) 10 5 (4 .63 – 4.87) 11 4 (4 .13 – 4.62) 12 4 (3 .88 – 4.12) 13 4 (3 .38 – 3.87) 14 3 (2 .88 – 3.37) 15 3 (2 .63 – 2.87) 16 2 (2 .13 – 2.62) 17 2 (1 .63 – 2.12) 18 1 (1 .13 – 1.62) 19 1 (0 .38 – 1.12) 20 0 (0 .00 – 0.37)

DN0933393 123


Create POC

Id:0900d805805c445d

9.21 pcLTQualUlRxQual

9.22 pcLowerThresholdsLevDLRxLevel

O bj P OC M ,O ,N,in ternal m apped Val

F ul l Name P C Low er T hresholds Qual UL Rx Qual T ype E num eration Range < 0 .2% (0), 0 .2% - 0 .4% (1), 0 .4% - 0 .8% (2), 0 .8% - 1 .6% (3), 1 .6% -

3 .2% (4), 3 .2% - 6 .4% (5), 6 .4% - 12.8% (6), > 12.8% (7) In terna l Va lue gui_va lue Default 0 .8% - 1 .6% (3) Descrip tion T he parameters compare the averaged va lues of signal quality up link

m easurem ents fo r triggering the power contro l p rocess 3Gpp M ultip 1 M odi fication O n-L ine M odi fied onCreate optional Val [PW RC] LOW TQ UAU

0,1 7 (6.88 – 7.00) 2 7 (6.76 – 6.87) 4 7 (6.38 – 6.75) 5 6 (6.13 – 6.37) 6 6 (5.88 – 6.12) 7 6 (5.63 – 5.87) 8 6 (5.13 – 5.62) 9 5 (4.88 – 5.12) 10 5 (4.63 – 4.87) 11 4 (4.13 – 4.62) 12 4 (3.88 – 4.12) 13 4 (3.38 – 3.87) 14 3 (2.88 – 3.37) 15 3 (2.63 – 2.87) 16 2 (2.13 – 2.62) 17 2 (1.63 – 2.12) 18 1 (1.13 – 1.62) 19 1 (0.38 – 1.12) 20 0 (0.00 – 0.37)

Obj POC M,O,N,internal mapped Val

Ful l Name PC Lower Thresholds Lev DL Rx Level Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -85 dBm Description The parameters compare the averaged values of signal

qual ity downlink measurements for triggering the power control process

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [PW RC] LOWTLEVD

124DN0933393


Id:0900d805805c445d

Create POC

9.23 pcLowerThresholsLevULRxLevel

9.24 pcRedStepSize

Obj POC M,O,N,internal mapped Val

Full Name PC Lower Thresholds Lev UL Rx Level Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -85 dBm Description The parameters compare the averaged values of signal

quality uplink measurements for triggering the power control process

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [PWRC] LOWTLEVU

Obj POC M,O,N,internal mapped Val

Full Name Power Red Step Size Type Number Range 2...4 dB, step 2 dB Internal Value (gui_value - 2) / 2 Default 2 dB Description Defines the step size for reducing the transmission power of the mobile

station 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [PWRC] PWREDSS:

DB2 --> 2 DB4 --> 4

DN0933393 125


Create POC

Id:0900d805805c445d

9.25 pcUTQualDlRxQualO bj P O C M ,O ,N,in ternal m apped V al

F ul l Name P C Upper Thresholds Q ual DL Rx Q ual T ype E num eration Range < 0.2% (0), 0 .2% - 0 .4% (1), 0.4% - 0 .8% (2), 0.8% - 1 .6% (3), 1 .6% -

3 .2% (4), 3.2% - 6 .4% (5), 6 .4% - 12.8% (6), > 12.8% (7) In terna l Va lue gu i_va lue Default < 0.2% (0) Descrip tion T he param eters com pare the averaged va lues of signal quality

downlink m easurem ents for triggering the power contro l process 3Gpp M ultip 1 M odi fication O n-L ine M odi fied onCreate optiona l Val [P WRC] UP TQU AD

0,1 7 (6.88 – 7.00) 2 7 (6.76 – 6.87) 4 7 (6.38 – 6.75) 5 6 (6.13 – 6.37) 6 6 (5.88 – 6.12) 7 6 (5.63 – 5.87) 8 6 (5.13 – 5.62) 9 5 (4.88 – 5.12) 10 5 (4.63 – 4.87) 11 4 (4.13 – 4.62) 12 4 (3.88 – 4.12) 13 4 (3.38 – 3.87) 14 3 (2.88 – 3.37) 15 3 (2.63 – 2.87) 16 2 (2.13 – 2.62) 17 2 (1.63 – 2.12) 18 1 (1.13 – 1.62) 19 1 (0.38 – 1.12) 20 0 (0.00 – 0.37)

126DN0933393


Id:0900d805805c445d

Create POC

9.26 pcUTQualUlRxQual

9.27 pcUpperThresholdsLevDLRxLevel

O bj P O C M ,O ,N,in ternal m apped V al

F ul l Name P C Upper Thresholds Q ual UL Rx Q ual T ype E numeration Range < 0.2% (0), 0 .2% - 0 .4% (1), 0 .4% - 0 .8% (2), 0.8% - 1 .6% (3), 1.6% -

3 .2% (4), 3 .2% - 6 .4% (5), 6.4% - 12.8% (6), > 12.8% (7) In terna l Va lue gu i_va lue Default < 0.2% (0) Descrip tion T he param eters com pare the averaged va lues of signal qua lity up link

m easurem ents for tr iggering the power contro l process . 3Gpp M ultip 1 M odi fication O n-L ine M odi fied onCreate optiona l Val [P WRC ] U PT Q UAU

0,1 7 (6.88 – 7.00) 2 7 (6.76 – 6.87) 4 7 (6.38 – 6.75) 5 6 (6.13 – 6.37) 6 6 (5.88 – 6.12) 7 6 (5.63 – 5.87) 8 6 (5.13 – 5.62) 9 5 (4.88 – 5.12) 10 5 (4.63 – 4.87) 11 4 (4.13 – 4.62) 12 4 (3.88 – 4.12) 13 4 (3.38 – 3.87) 14 3 (2.88 – 3.37) 15 3 (2.63 – 2.87) 16 2 (2.13 – 2.62) 17 2 (1.63 – 2.12) 18 1 (1.13 – 1.62) 19 1 (0.38 – 1.12) 20 0 (0.00 – 0.37)

Obj POC M,O,N,internal mapped Val

Ful l Name PC U pper Thresholds Lev DL Rx Level Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -70 dBm Description The parameters compare the averaged values of signal

qual ity downlink measurements for triggering the power control process .

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [PWR C] UPTLEVD

DN0933393 127


Create POC

Id:0900d805805c445d

9.28 pcUpperThresholdsLevULRxLevel

9.29 pcControlEnabled

Obj POC M,O,N,internal mapped Val

Ful l Name PC U pper Thresholds Lev U L R x Level Type Number Range -110...-47, step 1 Internal Value (gui_value + 110) Default -70 Description The parameters compare the averaged values of signal

quality upl ink measurements for triggering the power control process.

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [PW RC] UPTLEVU

Obj POC M,O,N,internal O Val Full Name Power CTRL Enabled Type Enumeration Range power control is disabled (N) (0), power control is enabled (Y) (1) Internal Value gui_value Default power control is enabled (Y) (1) Description With this parameter you indicate whether the BTS power control

is enabled 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val See powerDecrQualFactor

128DN0933393


Id:0900d805805c445d

Create POC

9.30 powerDecrQualFactorObj POC M,O,N,internal mapped Val Full Name Power Decr Qual Factor Type Enumeration Range Disabled (0), Enabled (1) Internal Value gui_value Default Enabled (1) Description With this parameter you enable or disable the MS power

decrease due to signal quali ty w ith the defined variable power change step size

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val switch ([PWRC]EMSPWRC/ EMSPWRC)

case DISABLED: { pcControlEnabled = 0 } case CLASSIC { pcControlEnabled = 1 powerDecrQualFactor = 0 } case ADAPTIVE { pcControlEnabled = 1 powerDecrQualFactor = 1 } (same for EBSPWRC & EMSPWRC: the assumption is that for UL and DL same policy will be used by operator)

DN0933393 129


Create HOC

Id:0900d805805c4e2e

10 Create HOC

10.1 amhTrhoPbgtMargin

10.2 averagingWindowSizeAdjCell

Create HOC Example from Real NetAct Configuration script managedObject class="HOC" operation="create" version="S14.1" distName="BSC-12345/BCF-45/BTS-223/HOC-1">

<defaults name="ESTemplate"/> /managedObject>

Obj HOC M,O,N,internal M.mapped Val

Full Name AMH TRHO PBGT Margin Type Number Range -24...24 dBm, step 1 dBm Internal Value gui_value Default 255 dBm Description Defines the power budget margin used in Advance Multilayer

Handling when the load of the cell exceeds the value defined with the amh upper load threshold (AUT) parameter of the EEM command

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val -24 + ([ADJC] TRFHOM / (126 / 48))

Obj HOC M,O,N,internal M Val

Full Name Adjacent Cell Averaging Window Size Type Number Range 1...32 SACCH Periods, step 1 SACCH Periods Internal Value gui_value Default 6 SACCH Periods Description Defines the window size for averaging the signal quality,

s ignal level and distance measurement results 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 6

130DN0933393


Id:0900d805805c4e2e

Create HOC

10.3 ddeThresholdsLevRxLevel

Obj HOC M,O,N,internal mapped Val

Full Name Threshold Deep Dropping EDGE Type Number Range 0...63 dB, step 1 dB Internal Value gui_value Default 10 dB Description The parameter is used for comparing the size of the signal drop

for triggering the rapid field drop handover 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [HAND] THLEVFULHO

DN0933393 131


Create HOC

Id:0900d805805c4e2e

10.4 enaFastAveHo

10.5 enableIntraHoDl

Obj HOC M,O,N,internal Mapped Val

Full Name Enable Fast Averaging HO Type Enumeration Range method is disabled (N) (0), method is enabled (Y) (1) Internal Value gui_value Default method is disabled (N) (0) Description With this parameter you indicate whether the Fast Handover Measurement

Averaging Method is enabled after handovers and in the new TCH 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] EFULHO:

• TRUE ? 1 • FALSE ? 0

Obj HOC M,O,N,internal Mapped Val

Full Name Enable Intracell Handover Interference DL Type Enumeration Range handover control is disabled (N) (0), handover control is enabled (Y) (1) Internal Value gui_value Default handover control is disabled (N) (0) Description Indicates whether an intracell handover caused by downlink interference is

enabled. Note! If this parameter is True, Enable Intracell HO and Enable Intracell HO UL must be False.

3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] INTRACH:

132DN0933393


Id:0900d805805c4e2e

Create HOC

10.6 enableIntraHoUl

10.7 enableMsDistance

Obj HOC M,O,N,internal Mapped Val

Full Name Enable Intracell Handover Interference UL Type Enumeration Range handover control is disabled (N) (0), handover control is enabled (Y) (1) Internal Value gui_value Default handover control is disabled (N) (0) Description Indicates whether an intracell handover caused by uplink interference is

enabled.Note! If this parameter is True, Enable Intracell HO and Enable Intracell HO DL must be False.

3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] INTRACH:


Obj HOC M,O,N,internal Mapped Val

Full Name Enable MS Distance Process Type Enumeration Range distance process is disabled (N) (0), distance process is enabled (Y)

(1) Internal Value gui_value Default distance process is disabled (N) (0) Description With this parameter you indicate whether the BTS - MS distance

process is enabled 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] DISTHO:

DN0933393 133


Create HOC

Id:0900d805805c4e2e

10.8 enablePowerBudgetHo

10.9 enableSddchHandover

Obj HOC M,O,N,internal mapped Val

Full Name Enable Power Budget Handover Type Enumeration Range handover control is disabled (N) (0), handover control is enabled

(Y) (1) Internal Value gui_value Default handover control is enabled (Y) (1) Description With this parameter you indicate whether the BTS power budget

handover control is enabled 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [HAND] PBGTHO:


Obj HOC M,O,N,internal Mapped Val

Full Name Enable SDCCH Handover Type Enumeration Range handover is disabled (N) (0), handover is enabled (Y) (1) Internal Value gui_value Default handover is disabled (N) (0) Description With this parameter you indicate whether the BTS SDCCH

handover is enabled 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] (IERCHOSDCCH or IRACHOSDCCH):

134DN0933393


Id:0900d805805c4e2e

Create HOC

10.10 enableUmbrellaHo

10.11 hoAvaragingLevDLWeighting

Obj HOC M,O,N,internal Mapped Val

Full Name Enable Umbrella Handover Type Enumeration Range handover is disabled (N) (0), handover is enabled (Y) (1) Internal Value gui_value Default handover is disabled (N) (0) Description With this parameter you indicate whether the BTS umbrella handover

is enabled 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] HIERC:


Obj HOC M,O,N,internal mapped Val

Full Name Level Downlink Weighting Type Number Range 1...3, step 1 Internal Value gui_value Default 1 Description The parameters calculate averaged values from signal

strength downlink measurements 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field DTX weighting factor of [HAND] HOAVLEV

DN0933393 135


Create HOC

Id:0900d805805c4e2e

10.12 hoAvaragingLevDlWindowSize

10.13 hoAveragingLevUlWeighting

Obj HOC M,O,N,internal mapped Val

Full Name Level Downlink Window Size Type Number Range 1...32, step 1 Internal Value gui_value Default 6 Description The parameters calculate averaged values from signal

strength downlink measurements 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field averaging period of [HAND] HOAVLEV

Obj HOC M,O,N,internal mapped Val

Full Name Level Uplink Weighting Type Number Range 1...3, step 1 Internal Value gui_value Default 1 Description The parameters calculate averaged values from signal

strength uplink measurements 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field DTX weighting factor of [HAND] HOAVLEV

136DN0933393


Id:0900d805805c4e2e

Create HOC

10.14 hoAveragingLevUlWindowSize

10.15 hoAveragingQualDlWeighting

Obj HOC M,O,N,internal mapped Val

Full Name Level Uplink Window Size Type Number Range 1...32, step 1 Internal Value gui_value Default 6 Description The parameters calculate averaged values from signal

strength uplink measurements 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field averaging period of [HAND] HOAVLEV

Obj HOC M,O,N,internal mapped Val

Full Name Quality Downlink Weighting Type Number Range 1...3, step 1 Internal Value gui_value Default 1 Description The parameters calculate averaged values from signal

quality downlink measurements 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field DTX weighting factor of [HAND] HOAVQUAL

DN0933393 137


Create HOC

Id:0900d805805c4e2e

10.16 hoAveragingQualDlWindowSize

10.17 hoAveragingQualUlWeighting

Obj HOC M,O,N,internal mapped Val

Full Name Quality Downlink Window Size Type Number Range 1...32, step 1 Internal Value gui_value Default 1 Description The parameters calculate averaged values from signal

quality downlink measurements 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field averaging period of [HAND] HOAVQUAL

Obj HOC M,O,N,internal mapped Val

Full Name Quality Uplink Weighting Type Number Range 1...3, step 1 Internal Value gui_value Default 1 Description The parameters calculate averaged values from signal

quality uplink measurements 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field DTX weighting factor of [HAND] HOAVQUAL

138DN0933393


Id:0900d805805c4e2e

Create HOC

10.18 hoAveragingQualUlWindowSize

10.19 hoPeriodPbgt

Obj HOC M,O,N,internal mapped Val

Full Name Quality Uplink Window Size Type Number Range 1...32, step 1 Internal Value gui_value Default 1 Description The parameters calculate averaged values from signal

quality uplink measurements 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val Field averaging period of [HAND] HOAVQUAL

Obj HOC M,O,N,internal Mapped Val

Full Name Handover Period Power Budget Type Number Range 0...63, step 1 Internal Value gui_value Default 6 Description Defines the interval between power budget handover threshold

comparisons 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val ([HAND] HOAVPWRB – 1) / (30 / 63))

DN0933393 139


Create HOC

Id:0900d805805c4e2e

10.20 hoTLDlPx

10.21 hoTLDlRxLevel

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Level Downlink Px Type Number Range 1...32, step 1 Internal Value gui_value Default 1 Description The parameters compare the averaged values of signal strength downlink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1 + ([HAND] HOLTHLVDL / (63 / 31))

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Level Downlink Rx Level Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -95 dBm Description The parameters compare the averaged values of signal strength downlink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] HOLTHLVDL

140DN0933393


Id:0900d805805c4e2e

Create HOC

10.22 hoTLUlNx

10.23 hoTLUlPx

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Level Uplink Nx Type Number Range 1...32, s tep 1 Internal Value gui_value Default 1 Description The parameters compare the averaged values of signal strength uplink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1 + ([HAND] HOLTHLVUL / (63 / 31))

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Level Uplink Px Type Number Range 1...32, step 1 Internal Value gui_value Default 1 Description The parameters compare the averaged values of signal strength uplink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1 + ([HAND] HOLTHLVUL / (63 / 31))

DN0933393 141


Create HOC

Id:0900d805805c4e2e

10.24 hoTLUlRxLevel

10.25 hoTQDlNx

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Level Uplink Rx Level Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -95 dBm Description The parameters compare the averaged values of s ignal strength uplink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] HOTULINT

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Qual Downlink Nx Type Number Range 1...32, step 1 Internal Value gui_value Default 6 Description The parameters compare the averaged values of signal quality downlink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1 + ([HAND] HOLTHQUDL / (20 / 31))

142DN0933393


Id:0900d805805c4e2e

Create HOC

10.26 hoTQDlPx

10.27 hoTQDlRxQual

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Qual Downlink Px Type Number Range 1...32, step 1 Internal Value gui_value Default 4 Description The parameters compare the averaged values of signal quality downlink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1 + ([HAND] HOLTHQUDL / (20 / 31))

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Qual Downlink Rx Qual Type Enumeration Range < 0.2% (0), 0.2% - 0.4% (1), 0.4% - 0.8% (2), 0.8% - 1.6% (3), 1.6% - 3.2%

(4), 3.2% - 6.4% (5), 6.4% - 12.8% (6), > 12.8% (7) Internal Value gui_value Default 1.6% - 3.2% (4) Description The parameters compare the averaged values of signal quality downlink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] HOLTHQUDL / (20 / 7)

DN0933393 143


Create HOC

Id:0900d805805c4e2e

10.28 hoTQUlNx

10.29 hoTQUlPx

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Qual Uplink Nx Type Number Range 1...32, step 1 Internal Value gui_value Default 6 Description The parameters compare the averaged values of signal quality uplink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1 + ([HAND] HOLTHQUUL / (20 / 31))

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Qual Uplink Px Type Number Range 1...32, step 1 Internal Value gui_value Default 4 Description The parameters compare the averaged values of signal quality uplink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1 + ([HAND] HOLTHQUUL / (20 / 31))

144DN0933393


Id:0900d805805c4e2e

Create HOC

10.30 hoTQUlRxQual

10.31 hoThresholdsInterferenceDlRxLevel

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Qual Uplink Rx Qual Type Enumeration Range < 0.2% (0), 0.2% - 0.4% (1), 0.4% - 0.8% (2), 0.8% - 1.6% (3), 1.6% - 3.2%

(4), 3.2% - 6.4% (5), 6.4% - 12.8% (6), > 12.8% (7) Internal Value gui_value Default 1.6% - 3.2% (4) Description The parameters compare the averaged values of signal quality uplink

measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] HOLTHQUUL / (20 / 7)

Obj HOC M,O,N,internal mapped Val

Full Name Threshold Interference Downlink Rx Level Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -85 dBm Description The parameters compare the averaged values of

interference downlink measurements for triggering the handover process

3Gpp The parameters compare the averaged values of signal strength downlink measurements for triggering the handover process.

Multip 1 Modification On-Line Modified onCreate optional Val [HAND] HOTDLINT

DN0933393 145


Create HOC

Id:0900d805805c4e2e

10.32 hoThresholdsInterferenceULRxLevel

10.33 hoThresholdsLevDLNx

Obj HOC M,O,N,internal mapped Val

Full Name Threshold Interference Uplink Rx Level Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -85 dBm Description The parameters compare the averaged values of

interference uplink measurements for triggering the handover process

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [HAND] HOTULINT

Obj HOC M,O,N,internal Mapped Val

Full Name Threshold Level Downlink Nx Type Number Range 1...32, step 1 Internal Value gui_value Default 1 Description The parameters compare the averaged values of signal strength

downlink measurements for triggering the handover process 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1 + ([HAND] HOLTHLVDL / (63 / 31))

146DN0933393


Id:0900d805805c4e2e

Create HOC

10.34 intraHoLoRxLevLimAmrHr

10.35 maxMsDistanceHoThreshold

Obj HOC M,O,N,internal mapped Val

Full Name Intra HO Lower Rx Level Limit AMR HR Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -100 dBm Description This parameter defines the limit for averaged uplink and downlink signal

level. If averaged uplink or downlink signal level is worse than this parameter then the quality based intra cell handovers are not allowed

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [HAND] HRDCMLIMTH / (100 / 147)

Obj HOC M,O,N,internal mapped Val

Full Name MS Distance HO Threshold Ext Cell Max Type Number Range 0...63, step 1 Internal Value gui_value Default 63 Description Defines the threshold level for the maximum value of timing

advance. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 63:

HERE THE INTERNAL BTS BEHAVIOUR IS MODIFIED ADOPTING THE BSS CURRENT SOLUTION. THUS HOMSTAM IS SUPERSEEDED BY THE BSS PARAMETER

DN0933393 147


Create HOC

Id:0900d805805c4e2e

10.36 minIntBetweenHoReq

10.37 minIntBetweenUnsuccHoAttempt

Obj HOC M,O,N,internal Mapped Val

Full Name Min Int Between HO Req Type Number Range 0...31 s, step 1 s Internal Value gui_value Default 5 s Description Defines the minimum interval between handovers related to the

same connection 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [HAND] THORQST

Obj HOC M,O,N,internal mapped Val

Full Name Min Int Between Unsucc HO Attempt Type Number Range 0...31 s, step 1 s Internal Value gui_value Default 3 s Description Defines the minimum interval between unsuccessful

handover attempts related to the same connection 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val ([ADJC] TINHFAIHO – 1) / (253 / 31))

148DN0933393


Id:0900d805805c4e2e

Create HOC

10.38 minIntUnsuccIsHo

10.39 minMsDistanceHoThreshold

Obj HOC M,O,N,internal Mapped Val

Full Name Min Interval Between Unsucc ISHO Attempt Type Number Range 0...255 s, step 1 s Internal Value gui_value Default 3 s Description With this parameter you define the minimum length of time interval

between inter-system handover attempts related to the same connection and the same non-GSM cell when a handover attempt from the serving GSM cell to a non-GSM cell has been unsuccessful.

3Gpp MIN_INTERVAL_BETWEEN_UNSUCC_ISHO_ATTEMPT Multip 1 Modification On-Line Modified onCreate Optional Val [ADJC] TINHFAIHO

Obj HOC M,O,N,internal mapped Val

Full Name MS Distance HO Threshold Ext Cell Min Type Number Range 0...63, step 1 Internal Value gui_value Default 2 Description Defines the threshold level of minimum value of timing

advance. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 2

HERE THE INTERNAL BTS BEHAVIOUR IS MODIFIED ADOPTING THE BSS CURRENT SOLUTION. THUS HOMRGTA IS SUPERSEEDED BY THE BSS PARAMETER

DN0933393 149


Create HOC

Id:0900d805805c4e2e

10.40 modifiedAveWinNCell

10.41 msDistanceAveragingParamHreqave

Obj HOC M,O,N,internal Mapped Val

Full Name Modified Averaging Window Type Number Range 1...32, step 1 Internal Value gui_value Default 2 Description With this parameter you indicate the new averaging window size of

the serving cell and adjacent cell 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1st Field (averaging period or size) of [HAND] ALEVFULHO

Obj HOC M,O,N,internal mapped Val

Full Name MS Distance Averaging Window Size Type Number Range 1...32, step 1 Internal Value gui_value Default 10 Description The parameter is the averaging parameter for

triggering the handover process because the MS is out of the cell boundary

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [HAND] HOAVDIST

150DN0933393


Id:0900d805805c4e2e

Create HOC

10.42 msDistHoParamMsRngMax

10.43 msSpeedDetectionState

Obj HOC M,O,N,internal mapped Val

Full Name MS Distance Threshold Param MS Max Range Type Number Range 0...63 bits, step 1 bits Internal Value gui_value Default 63 bits Description The parameters compare the MS-BS distance with

the maximum allowed distance 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 63

HERE THE INTERNAL BTS BEHAVIOUR IS MODIFIED ADOPTING THE BSS CURRENT SOLUTION. THUS [BTS] excessiveDistanceand [HAND] hoThresholdMsRangeMax ARE SUPERSEEDED BY THE BSS PARAMETER (Hand-B.49) /

Obj HOC M,O,N,internal mapped Val

Full Name MS Speed Detection State Type Number Range 0...100, step 1 Internal Value gui_value Default 0 Description With this parameter you indicate the method used for MS speed

detection algorithm 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [HAND] DPBGTHO:

• TRUE ? 100 • FALSE ? 0

DN0933393 151


Create HOC

Id:0900d805805c4e2e

10.44 smaxMsDistanceHoThreshold

10.45 sminMsDistanceHoThreshold

Obj HOC M,O,N,internal M Val

Full Name MS Distance HO Threshold Super Ext Cell Max Type Number Range 0...63, step 1 Internal Value gui_value Default 63 Description With this parameter you define the timing advance threshold

when call is handed over from extended area to super extended area.


Obj HOC M,O,N,internal M Val

Full Name MS Distance HO Threshold Super Ext Cell Min Type Number Range 0...63, step 1 Internal Value gui_value Default 2 Description With this parameter you define the timing advance threshold

when call is handed over from super extended area to extended area.

152DN0933393


Id:0900d805805c4e2e

Create HOC

10.46 superReuseBadCiThresholdCiRatio

10.47 superReuseBadRxLevThresholdRxLevel

Obj HOC M,O,N,internal mapped Val

Full Name Super Reuse Bad C/I Threshold Type Number Range -127...127, step 1 Internal Value gui_value Default 10 Description The parameter compares the downlink C/I ratio on a

super-reused TRX for triggering a handover from the super-reused TRX


Obj HOC M,O,N,internal O Val

Full Name Super Reuse Bad Threshold Rx Level Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -85 dBm Descr The parameter is used for comparing the downlink signal

level of the super-reuse TRX for triggering the handover to a regular TRX

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [HAND] HORXLVDLI

DN0933393 153


Create HOC

Id:0900d805805c4e2e

10.48 superReuseGoodCiThresholdCiRatio

10.49 superReuseGoodRxLevThresholdRxLevel

Obj HOC M,O,N,internal mapped Val

Full Name Super Reuse Good C/I Threshold Type Number Range -127...127, step 1 Internal Value gui_value Default 17 Description The parameter compares the downlink C/I ratio on a

super-reused TRX for triggering a handover to the super-reused TRX


Obj: HOC M,O,N,internal: O Val

Full Name: Super Reuse Good Threshold Rx Level Type: Number Range: -110...-47 dBm, step 1 dBm Internal Value: (gui_value + 110) Default: -80 dBm Descr The parameter is used for comparing the downlink signal

level of the super-reuse TRX for triggering the handover to a regular TRX

3Gpp: Multip: 1 Modification: On-Line Modified: onCreate: optional Val: [HAND] HORXLVDLO

154DN0933393


Id:0900d805805c4e2e

Create HOC

10.50 interSystemDa

10.51 intraHoUpRxLevLimAmrHr

Obj HOC M,O,N,internal mapped Val Ful l Name Inter-System Direct Access Enabled Type Boolean Range false (0), true (1) Internal Value gui_value Default false (0) Description Inter-System Direct Access enabled 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [BSC] enableUmtsSdcchHo

Obj HOC M,O,N,internal mapped Val

Full Name Intra HO Upper Rx Level Limit AMR HR Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -47 dBm Description This parameter defines the limit for averaged uplink and

downlink signal level. If averaged uplink or downlink signal level is better than this parameter then the quality based intra cell handovers are not allowed.

3Gpp - Multip 1 Modification On-Line Modified onCreate optional Val mean value of [HAND] HOTHCMPLVUL & HOTHDCMLVUL

DN0933393 155


Create HOC

Id:0900d805805c4e2e

10.52 msSpeedThresholdNx

10.53 msSpeedThresholdPx

Obj HOC M,O,N,internal mapped Val Full Name MS Speed Threshold Nx Type Number Range 1...32, step 1 Internal Value gui_value Default 6 Description The parameter is used in threshold comparison between the

averaged MS speed and the upper and lower speed thresholds 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val take value:

1+ [ADJC] HOMSOFF/127/31 from each ADJC and collapse then form ADJCs to HAND object taking the mean value from ADJCs where speed sensitive HO was enabled (otherwise default 0 will be taken))

Obj HOC M,O,N,internal mapped Val Full Name MS Speed Threshold Px Type Number Range 1...32, step 1 Internal Value gui_value Default 3 Description The parameter is used in threshold comparison between the

averaged MS speed and the upper and lower speed thresholds 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val take value:

1+ [ADJC] HOMDOFF/127/31 from each ADJC and collapse then form ADJCs to HAND object taking the mean value from ADJCs where speed sensitive HO was enabled (otherwise default 0 will be taken))

156DN0933393


Id:0900d80580646a60

Create ADCE

11 Create ADCEWhen administering the BTSplus with the eBSC/BSC1, up to 64 ADJC objects can be configured per BTS object. After rehosting the BTSplus to the Flexi BSC, the maximum number of adjacent cells that can be configured for each BCF is 32. Therefore, only 32 of the BR adjacent cells can be used.

However, when using the eBSC/BSC1, the number of active adjacent cells in the system has to be lower or equal to 32. This number is reduced to to 31 if: • at least one 3G adjacent cell is equipped • the superordinate BTS has the EFCRESEL attribute set to true

Therefore, only those ADJC objects are migrated for which the USG attribute has a value other than inactive.

As shown in the above example, the distName value of the created ADCE object is derived by appending the values of the LAC and the CI fields from the CELLGLID attri-bute, and separating these by a space character.

11.1 adjCellBsicBcc

Create ADCE Example from Real NetAct Configuration script managedObject class="ADCE" version="S14.1" distName="PLMN-PLMN/BSC-12345/BCF-45/BTS-198/ADCE-5210 4592" operation="create">

<defaults name="ESTemplate"/> 44592 5210 2 5 766

/managedObject>

Obj ADC E M,O,N,internal M.mapped Val Ful l Name BSIC BCC Type Number Range 0...7, step 1 Internal Value gui_value Default Description BTS Colour Code 3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val BCC field of [ADJC- TGTCELL] BSIC

DN0933393 157


Create ADCE

Id:0900d80580646a60

11.2 adjCellBsicNcc

11.3 adjacentCellIdCI

11.4 adjacentCellIdLac

Obj ADCE M,O,N,internal M.mapped Val Ful l Name BSIC N CC Type Number Range 0...7, step 1 Internal Value gui_value Default Description Network C olour Code 3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val NCC field of [ADJC- TGTCELL] BSIC

Obj ADCE M,O,N,internal M.mapped Val Ful l Name CI Type Number Range 0...65535, step 1 Internal Value gui_value Default Description CI of adjacent cell (target cell). 3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val CI field of [ADJC - TGTCELL] CELLGLID

Obj ADCE M,O,N,internal M Val Ful l Name LAC Type Number Range 1...65533, s tep 1 Internal Value gui_value Default Description LAC of adjacent cell (target cell). 3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val LAC field of [ADJC- TGTCELL] CELLGLID

158DN0933393


Id:0900d80580646a60

Create ADCE

11.5 adjacentCellIdMCC

11.6 adjacentCellIdMNC

Obj ADCE M,O,N,internal M.mapped Val

Full Name MCC Type String Range 3 characters Internal Value gui_value Default Description MCC of adjacent cell (target cell).This parameter is automatically

copied from the target BTS. 3Gpp MCC Multip 1 Modification Not modifiable Modified onCreate Optional Val MCC field of [ADJC- TGTCELL] CELLGLID

Obj ADCE M,O,N,internal M.mapped Val

Full Name MNC Type String Range 2...3 characters Internal Value gui_value Default Description MNC of adjacent cell (target cell).This parameter is automatically

copied from the target BTS. 3Gpp MNC Multip 1 Modification Not modifiable Modified onCreate Optional Val MNC field of [ADJC- TGTCELL] CELLGLID

DN0933393 159


Create ADCE

Id:0900d80580646a60

11.7 bcchFrequency

11.8 chainedAdjacentCell

Obj ADCE M,O,N,internal M.mapped Val Ful l Name BCCH Frequency Type Number Range 0...65535, step 1 Internal Value gui_value Default Description BCCH frequency of an adjacent cel l (target BTS) 3Gpp Multip 1 Modification Not modifiable Modified onCreate Mandatory Val [AD JC- TGTCELL] BCCHFREQ

Obj ADCE M,O,N,internal M.mapped Val

Full Name Chained Adj Cell Type Enumeration Range adjacent cell is not chained (N) (0), adjacent cell is chained (Y) (1) Internal Value gui_value Default adjacent cell is not chained (N) (0) Description Defines the adjacent cell as a chained cell, to which the rapid field

drop handover criteria are applied 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [ADJC] FULHOC:

• TRUE 1 • FALSE 0

160DN0933393


Id:0900d80580646a60

Create ADCE

11.9 dtmPowerBudgetMargin

11.10 enableHoMarginLevQual

Obj ADCE M,O,N,internal M.mapped Val

Ful l Name DTM Power Budget Margin Type Number Range -24...63 dB, step 1 dB Internal Value (gui_value + 24) Default 6 dB Description W ith this parameter you define a power budget handover

threshold. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val i f ([Hand] DTMPBGTHO ==FALSE)

{ dtmPowerBudgetMargin = 87 /* 63 dB */ } else { dtmPowerBudgetMargin = [ADJC] DTMHOM - 39 }

Obj ADCE M,O,N,internal M.mapped Val

Full Name Enable HO Margin Lev Qual Type Enumeration Range not used (N) (0), used (Y) (1) Internal Value gui_value Default used (Y) (1) Description Defines whether the handover margins for signal level and quality

will be taken into account in the handover decision algorithm 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [Hand] (ELEVHOM or ENAQUALEVHOM):

• FALSE 0 • TRUE: 1

For up to the max 32 ADCEs set 1 if ELEVHOM or ENAQUALEVHOM are TRUE, and 0 if they are both FALSE/skipped.

DN0933393 161


Create ADCE

Id:0900d80580646a60

11.11 fastMovingThreshold

11.12 gprsEnabled

Obj ADCE M,O,N,internal Mapped Val

Full Name Fast Moving Threshold Type Number Range 0...255 SACCH frames, step 1 SACCH frame (Unit is SACCH fram es) Internal Value gui_value Default 0 SACCH fr Description Defines the limit which is compared with the identification counter

(fast moving MS) in the adjacent cell 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [ADJC]. HOMDTIME

Obj ADCE M,O,N,internal M Val

Full Name GPRS Enabled Type Enumeration Range GPRS is disabled in the adjacent cell (N ) (0), GPRS is enabled in the

adjacent cell (Y) (1) Internal Value gui_value Default GPRS is disabled in the adjacent cell (N ) (0) Description The attribute is used to enable or disable the GPRS capabil ity during the

normal operation of the adjacent cell (target BTS) 3Gpp Multip 1 Modification Not modifiable Modified onCreate Optional Val [ADJC] GSUP:

• TRUE 1 • FALSE 0

162DN0933393


Id:0900d80580646a60

Create ADCE

11.13 gprsMsTxPwrMaxCCH1x00

11.14 gprsMsTxpwrMaxCCH

Obj ADCE M,O,N,internal M Val

Full Name GPRS MS Tx Pwr Max CCH 1x00 Type Number Range 0...36 dBm, step 2 dBm Internal Value gui_value Default 30 dBm Description With this parameter you define the maximum transmission

power an MS may use when accessing a packet control channel in the adjacent cell. This is used when BCCH is in GSM 1900 or GSM 1800 frequency band.

3Gpp Multip 1 Modification Not modifiable Modified onCreate optional Val 30

Obj ADCE M,O,N,internal M Val

Full Name GPRS MS Tx Pwr Max CCH Type Number Range 5...39 dBm, step 2 dBm Internal Value (gui_value - 43) / -2 Default 33 dBm Description Attribute defines maximum transmission power level a mobile

station may use when accessing a packet control channel in the adjacent cell (target BTS)

3Gpp Multip 1 Modification Not modifiable Modified onCreate optional Val 5 (33 dBm)

DN0933393 163


Create ADCE

Id:0900d80580646a60

11.15 gprsPenaltyTime

11.16 gprsRxlevAccessMin

Obj ADCE M,O,N,internal M Val

Full Name GPRS Penalty Time Type Number Range 10...320 s, step 10 s Internal Value (gui_value - 10) / 10 Default 10 s Description Attribute defines the duration for which the GPRS Temporary Offset is

applied 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [ADJC] GPENTIME

Obj ADCE M,O,N,internal M Val

Full Name GPRS Rxlev Access Min Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -105 dBm Description Attribute defines minimum power level the mobile station has to

receive before it is allowed to access the cell 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 5 (-105 dBm)

164DN0933393


Id:0900d80580646a60

Create ADCE

11.17 gprsTemporaryOffset

11.18 hcsPriorityClass

Obj ADCE M,O,N,internal M Val

Full Name GPRS Temporary Offset Type Number Range 0...70 dB, step 10 dB Internal Value gui_value / 10 Default 0 dB Description Defines the negative offset of the C32 reselection criterion for the

duration of the GPRS penalty time (GPET) after the MS has placed the cell on the list of the strongest carriers

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [ADJC] GTEMPOFF

Obj ADCE M,O,N,internal Mapped Val

Full Name Priority Class Type Number Range 0...7, step 1 Internal Value gui_value Default 0 Description Attribute indicates he HCS (hierarchical cell structures) priority for the

adjacent cell (target BTS) 3Gpp Multip 1 Modification Not modifiable Modified onCreate Optional Val [ADJC] PPLNC / 2

DN0933393 165


Create ADCE

Id:0900d80580646a60

11.19 hcsThreshold

11.20 hoMarginLev

11.21 hoMarginPbgt

Obj ADCE M,O,N,internal M Val

Full Name HCS Threshold Type Number Range -110...-48 dB, step 2 dB Internal Value (gui_value + 110) / 2 Default 255 dB Description Attribute defines signal strength threshold the adjacent cell (target BTS) for

applying HCS in GPRS and LSA reselection 3Gpp Multip 1 Modification Not modifiable Modified onCreate Optional Val 255

Obj ADCE M,O,N,internal Mapped Val Ful l Name HO Margin Lev Type Number Range -24...24 dB, step 1 dB Internal Value gui_value Default 3 dB Description Defines a threshold for a handover caused by signal level 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val -24 + ([ADJC] LEVHOM / (126 / 48))

Obj ADCE M,O,N,internal mapped Val Ful l Name H O Margin PBGT Type N umber Range -24...63 dB, step 1 dB Internal Value gui_value Default 6 dB Description D efines a threshold in the power budget process 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val -24 + ([ADJC] HOM / (126 / 87))

166DN0933393


Id:0900d80580646a60

Create ADCE

11.22 hoMarginQual

11.23 hoPriorityLevel

11.24 msTxPwrMaxGSM

Obj ADCE M,O,N,internal mapped Val Ful l Name HO Margin Qual Type Number Range -24...24 dB, step 1 dB Internal Value gui_value Default 0 dB Description Defines a threshold for a handover caused by signal quality 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val -24 + ([ADJC] QUALLEVHOM / (126 / 48))

Obj ADCE M,O,N,internal mapped Val Ful l Name HO Priority Level Type Number Range 0...7, step 1 Internal Value gui_value Default 3 Description Defines the priority level for an adjacent cell3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [ADJC ] PLNC / 2

Obj ADCE M,O,N,internal mapped Val

Full Name MS Tx Pwr Max GSM Type Number Range 5...39 dBm, step 2 dBm Internal Value (gui_value - 43) / -2 Default 33 dBm Description The attribute defines max MS transmitting power in adjacent cell (target

BTS) for GSM band (GSM 900/GSM 850) 3Gpp Multip 1 Modification Not modifiable Modified onCreate optional Val [TGTBTS] MSTXPMAXGSM (1:1 mapping)

DN0933393 167


Create ADCE

Id:0900d80580646a60

11.25 msTxPwrMaxGSM1x00

11.26 nccrEgprsPbgtMargin

O bj AD C E M ,O ,N ,in tern a l map ped Va l

F ul l N ame MS Tx P w r Ma x G S M1x00 T ype N um ber R ange 0 ...3 6 , s tep 2 In te rna l Va lue G SM 1 800 :

0..3 0 dBm : 0 ..1 5 (U I va lue - 3 0 )/-2 32 dB m: 3 1 34 dB m: 3 0 36 dB m: 2 9 G SM 1 900 : 0..3 0 dBm : 0 ..1 5 (U I va lue - 3 0 )/-2 32 dB m: 3 1 33 dB m: 3 0

D e fau lt 3 0 D escr ip tio n The a ttri bu te de fines m a x M S tra ns mittin g pow er in a d ja cen t ce ll

(ta rge t B TS ) fo r G SM 1 800/19 00 ban d 3 G p p M u ltip 1 M o di fica tion N o t mod ifiab le M o di fied o nC re ate o ptiona l Va l [TG T BT S] M ST XP M AXD C S / [TG T B TS ] M S TX PM AX PC S :(1 :1

map p in g )

Obj ADCE M,O,N,internal M Val

Full Name NCCR And DTM EGPRS PBGT Margin Type Number Range -63...63 dB, step 1 dB Internal Value (gui_value + 63) Default 6 dB Description With this parameter you define the threshold which is used for

EGPRS and DTM MSs as a power budget margin in the NCCR and DTM power budget process.

168DN0933393


Id:0900d80580646a60

Create ADCE

11.27 nccrEgprsQualityMargin

11.28 nccrGprsPbgtMargin

Obj ADCE M,O,N,internal M Val

Full Name NCCR EGPRS Quality Margin Type Number Range -5...5 dB, step 1 dB Internal Value (gui_value + 5) Default 0 dB Description With this parameter you define the margin for EGPRS MS by

which the signal level of the neighbor cell must exceed the signal level of the serving cell before the cell reselection is possible.


Obj ADCE M,O,N,internal M Val

Full Name NCCR And DTM GPRS PBGT Margin Type Number Range -63...63 dB, step 1 dB Internal Value gui_value Default 6 dB Description With this parameter you define the threshold which is used for GPRS

and DTM MSs as a power budget margin in the NCCR and DTM power budget process.

DN0933393 169


Create ADCE

Id:0900d80580646a60

11.29 nccrGprsQualityMargin

11.30 rac

Obj ADCE M,O,N,internal M Val

Full Name NCCR GPRS Quality Margin Type Number Range -5...5 dB, step 1 dB Internal Value gui_value Default 0 dB Description With this parameter you define the margin for GPRS MS by which

the signal level of the neighbor cell must exceed the signal level of the serving cell before the cell reselection is possible.


Obj ADCE M,O,N,internal M Val

Full Name RAC Type Number Range 0...255, step 1 Internal Value gui_value Default 255 Description Routing Area Code (RAC) of adjacent cell (target BTS) is used for indentifying GPRS

cells 3Gpp Multip 1 Modification Not modifiable Modified onCreate Optional Val 255

170DN0933393


Id:0900d80580646a60

Create ADCE

11.31 levelAdj

11.32 reportingPriority

Obj ADCE M,O,N,internal Mapped Val

Full Name Reference Cell Level Adjustment Type Number Range -63...63 dB, step 1 dB Internal Value gui_value Default 0 dB Description With this parameter you define the difference in signal levels between the actual

co-frequency cell of the handover candidate and the reference cell which simulates the co-frequency cell.

3Gpp Multip 1 Modification On-Line Modified onCreate optional Val -63 + ([ADJC] LEVONC / (63 / 126))

Obj ADCE M,O,N,internal M Val

Full Name Reporting Priority Type Enumeration Range Reporting Priority Is Set To Normal (0), Reporting Priority Is Set To High

(1) Internal Value gui_value Default Reporting Priority Is Set To Normal (0) Description Identifies the reporting priority of the adjacent GSM cell 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

DN0933393 171


Create ADCE

Id:0900d80580646a60

11.33 rxLevMinCell

11.34 trhoTargetLevel

Obj ADCE M,O,N,internal mapped Val

Full Name RX Lev Min Cell Type Number Range -110...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default -100 dBm Description With this parameter you define the minimum signal level of an adjacent cell,

when a handover is allowed to one of them. 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val [ADJC] RXLEVMIN

Obj ADCE M,O,N,internal Mapped Val

Full Name TRHO Target Level Type Number Range -109...-47 dBm, step 1 dBm Internal Value (gui_value + 110) Default 0 dBm Description Defines the minimum signal level when a traffic reason handover is

allowed to an adjacent cell 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val 1 + ([ADJC] TRFHORXLVMOFF + 24) / (62 / 48))

172DN0933393


Id:0900d805805c5204

Create ADJW

12 Create ADJW

12.1 AdjwCId

12.2 cellParameter

Create ADJW Example from Real NetAct Configuration script managedObject class="ADJW" version="S14.1" distName="PLMN-PLMN/BSC-12345/BCF-45/BTS-198/ADJW-1" peration="create">

<defaults name="ESTemplate"/> 19040 244 05 190 10001

/managedObject>

Obj ADJW M,O,N,internal M.mapped Val Ful l Name Cell Identification Type Number Range 0...65535, step 1 Internal Value gui_value Default Description With this parameter you define the cell number for the adjacent UTRAN cell.3Gpp CELL_ID Multip 1 Modification On-Line Modified onCreate mandatory Val CI field of [ADJC3G- TGTC ELL] CELLGLID

Obj ADJW M,O,N,internal M.mapped Val

Full Name Cell Parameter Type Number Range 0...127, step 1 Internal Value gui_value Default 0 Description With this parameter you define the downlink cell parameter of the primary

common pilot channel of the adjacent TD-SCDMA RAN cell. 3Gpp Multip 1 Modification On-Line Modified onCreate mandatory Val [TGTTDD] TDDCPAR

DN0933393 173


Create ADJW

Id:0900d805805c5204

12.3 fddReportingPriority

12.4 isnccrFddQualityThr

Obj ADJW M,O,N,internal M Val

Full Name Reporting Priority Type Enumeration Range Reporting Priority Is Set To Normal (0), Reporting Priority Is Set To

High (1) Internal Value gui_value Default Reporting Priority Is Set To Normal (0) Description Identifies the reporting priority of the adjacent UTRAN cell 3Gpp Multip 1 Modification On-Line Modified onCreate optional Val 0

Obj ADJW M,O,N,internal M Val

Full Name ISNCCR FDD Quality Threshold Type Number Range -24...0.5 dB, step 0.5 dB Internal Value (gui_value + 24) * 2 Default -15 dB Description With this parameter you define the minimum signal quality level of an

adjacent WCDMA RAN cell for an inter-system network- controlled cell re-selection (ISNCCR).

174DN0933393


Id:0900d805805c5204

Create ADJW

12.5 lac

12.6 mcc

Obj ADJW M,O,N,internal M.mapped Val

Full Name LAC Type Number Range 1...65533, step 1 Internal Value gui_value Default Description With this parameter you define the location area that the adjacent UTRAN cell

belongs to. 3Gpp LAC Multip 1 Modification On-Line Modified onCreate Mandatory Val LAC field of [ADJC3G- TGTCELL] CELLGLID

Obj ADJW M,O,N,internal M.mapped Val

Full Name MCC Type String Range 3 characters Internal Value gui_value Default Description With this parameter you define the mobile country code number for the adjacent

UTRAN cell. 3Gpp MCC Multip 1 Modification On-Line Modified onCreate Mandatory Val MCC field of [ADJC3G- TGTCELL] CELLGLID

DN0933393 175


Create ADJW

Id:0900d805805c5204

12.7 minEcnoThreshold

12.8 mnc

Obj ADJW M,O,N,internal mapped Val

Full Name Minimum CPICH Ec/Io Level Type Number Range -24...0.5 dB, step 0.5 dB Internal Value (gui_value + 24) * 2 Default -15 dB Description With this parameter you define the minimum CPICH Ec/Io level of an

adjacent WCDMA RAN cell for an inter-system handover attempt. 3Gpp MIN_ECNO_THRESHOLD Multip 1 Modification On-Line Modified onCreate optional Val [ADJC3G] UMECNO

Obj ADJW M,O,N,internal M.mapped Val

Full Name MNC Type String Range 2...3 characters Internal Value gui_value Default Description With this parameter you define the mobile network code number for the adjacent

UTRAN cell. 3Gpp MNC Multip 1 Modification On-Line Modified onCreate Mandatory Val MNC field of [ADJC3G- TGTCELL] CELLGLID

176DN0933393


Id:0900d805805c5204

Create ADJW

12.9 rncId

12.10 scramblingCode

Obj ADJW M,O,N,internal M.mapped Val

Full Name RNC ID Type Number Range 1...4095, step 1 Internal Value gui_value Default Description With this parameter you define the radio network controller that controls the adjacent

UTRAN cell on the UTRAN network. 3Gpp Multip 1 Modification On-Line Modified onCreate Mandatory Val [TGTTDD / TGTFDD] RNCID:

• 0 log error • 1-4095 1-4095

Obj ADJW M,O,N,internal mapped Val

Full Name Scrambling Code Type Number Range 0...511, step 1 Internal Value gui_value Default Description With this parameter you define the downlink scrambling code of the

primary common pilot channel of the adjacent UTRAN cell. 3Gpp SCRAMBLING_CODE Multip 1 Modification On-Line Modified onCreate mandatory Val [TGTFDD] FDDSCRMC

DN0933393 177


Create ADJW

Id:0900d805805c5204

12.11 syncCase

12.12 txDiversityInd

Obj ADJW M,O,N,internal M.mapped Val

Full Name Synchronisation Case Type Enumeration Range Synchronisation case 1 is used (0), Synchronisation case 2 is used (1) Internal Value gui_value Default Synchronisation case 1 is used (0) Description With this parameter you define the adjacent TD-SCDMA RAN cell

synchronisation case 3Gpp Multip 1 Modification On-Line Modified onCreate Optional Val [TGTTDD] TDDSYNCCAS:

• SYNC1 0 • SYNC2 1

Obj ADJW M,O,N,internal M.mapped Val

Full Name Downlink Transmission Diversity Type Enumeration Range not used (N) (0), used (Y) (1) Internal Value gui_value Default not used (N) (0) Description With this parameter you define whether the downlink transmission diversity

capability of the logical node that is controlling the adjacent UTRAN cell is used or not.

3Gpp DIVERSITY Multip 1 Modification On-Line Modified onCreate Optional Val [TGTFDD] FDDDIV

• NO_DIVERSITY 0 • DIVERSITY 1

178DN0933393


Id:0900d805805c5204

Create ADJW

12.13 uarfcn

Obj ADJW M,O,N,internal M.mapped Val

Full Name WCDMA Downlink Carrier Frequency Type Number Range 0...16383, step 1 Internal Value gui_value Default Description Downlink carrier frequency of the adjacent UTRAN cell. Allowed channel numbers in

RF band I are 10562-10838. Allowed channel numbers in RF band II are 412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687, and 9663-9712, 9763-9812, 9888-9937.

3Gpp UARFCN Multip 1 Modification On-Line Modified onCreate mandatory Val [ADJC3G- TGTCELL] BCCHFREQ

parameter attribute mapping for migrating btsplus to the flexi bsc product family

Documents