p12x_envcc55 hard-soft ware

8/13/2019 p12x_envcc55 Hard-Soft Ware

1/12

Technical Guide P12x/EN VC/C55

MiCOM P120/P121/P122/P123

HARDWARE/SOFTWARE VERSION

P120 P121 P122 P123

HISTORY AND COMPATIBILITY


2/12


3/12

Technical Guide P12x/EN VC/C55Hardware/Software VersionMiCOM P120/P121/P122/P123 Page 1/10

P120 - Serial number Hardware Correlation

Serial Number Hardware installed

From 2299001 to 4799797 HARDWARE VERSION 2


From 1101001 HARDWARE VERSION 4

Relay Type P120

SoftwareVersion

Date ofIssue

Full Description of ChangesS1Compatibility

BackwardCompatibility withprevious hardware

V1.F 11/06/99 Resolution of KITZ201problem

Modification of the outputrelay latching

HARD V 2

HARD V 3HARD V 4

V3.B 19/11/99 Suppression of password inorder to acknowledge thealarms

Auto acknowledgement ofthe instantaneous

Modbus time out of 200 ms

Display of the letter P in the

menu N and N-1 whenpassword is active

!V2.0

V3.C 22/08/00 VDEW improvements !V2.0

HARD V 3

HARD V 4

V4.A 15/03/01 Integration of DNP3protocol

Management of alternativelogic input

Latching of the auxiliaryoutput relay by relay and

not by functionThe digital input can workwith AC signals (100 to 250

V AC)

!V2.0 HARD V 4

V4.D 27/08/02 Courier improvment :adding of the cell 0010 (CBcontrol)

IEC103 : correction of thechecksum calculation forshort message.

!V2.0 HARD V 4


4/12

P12x/EN VC/C55 Technical GuideHardware/Software Version

Page 2/10 MiCOM P120/P121/P122/P123






Relay Type P121

SoftwareVersion

Date ofIssue



V2.J 30/08/99 MODBUS improvement :

Correction of alencountered problem(answer to asynchronisation telegram,creation of a 2 secondstime out )

HARD V 2

HARD V 3HARD V 4




Display of the letter P in themenu N and N-1 whenpassword is active

!V2.0 HARD V 3

HARD V 4

V3.C 25/01/00 Evolution of Modbus writing16 bits

!V2.0

V3.E 16/03/00 Czech and Hungarianversion delivery

!V2.0

V3.G 22/08/00 VDEW improvements !V2.0


5/12


Relay Type P121

SoftwareVersion

Date ofIssue



V4.E 31/01/01 Latch of the output relaysLatch of the auxiliary relays,relay by relay and not byfunction (like previously upto V3 version). On the otherhand the latch of the TRIPoutput relay remains byfunction.

If the auxiliary relays arelatched, no alarm isdisplayed. For anaknowledgment of the latchthe user has to go in theOP-PARAMETERS/Relaystatus Menu and push onthe clear push button.

DNP3 level 2 and 3

Addition of the tripping andclosing order for IEC103

The digital input can work

with AC signals (100 to 250V AC)

!V2.0

V5.D 31/01/01 Improvement of the englishlabels.

!V2.0

HARD V 4

V5.F 08/08/02 Courier improvment :adding of the cell 0010 (CBcontrol)

IEC103 : correction of thechecksum calculation forshort message.

!V2.0 HARD V 4


6/12


Page 4/10 MiCOM P120/P121/P122/P123






Relay Type P122

SoftwareVersion

Date ofIssue




Correction of alencountered problem(answer to asynchronisation telegram,creation of a 2 secondstime out )

HARD V 2

HARD V 3HARD V 4




Display of the letter P in themenu N and N-1 whenpassword is active

!V2.0

V3.C 06/01/00 Label correction !V2.0

V3.D 06/04/00 Evolution of Modbus writing16 bits

!V2.0


!V2.0


HARD V 3

HARD V 4


7/12


Relay Type P122

SoftwareVersion

Date ofIssue



V4.E 31/01/01 Latch of the output relaysLatch of the auxiliary relays,relay by relay and not byfunction (like previously upto V3 version). On the otherhand the latch of the TRIPoutput relay remains byfunction.If the auxiliary relays arelatched,an alarm will be displayed.

If the user acknowledgesthis alarm, the auxiliaryrelays will be delatched.DNP3 level 2 and 3

Addition of the tripping andclosing order for IEC103Phase rotation (ABC or

ACB)Third threshold algorithmfor improvment of thebehaviour on saturatedcurrent transformersTimer for the undercurrentfeature (0 to 150 sec)Tripping curves (rectifiercurve + LABORELLECcurves)Selection of the Settinggroup by level or by edge.CB fail detection (possibilityto inhibit the startingsignals)Instanteneous record

Rolling demandPeak value demandInstantaneous alarmsettable : self or not selfresetMatrix for the autorecloserThe digital input can workwith AC signals signals (24

V to 250 V AC)Necessity to set in HMIConfiguration menu, the

type of voltage used, eitherACor DC

!V2.0 HARD V 4


8/12


Page 6/10 MiCOM P120/P121/P122/P123

Relay Type P122

SoftwareVersion

Date ofIssue



V5.A 27/09/01 Maintenance mode formanual command of theoutput relays

Reset of leds by logic inputor control command orfront panel or on new faultappearance

Addition of negativesequence protection feature(ANSI code 46) with twothresholds

Addition of the CBsupervision feature.

!V2.0

V5.C 04/10/01 VDEW improvements

(Updating of theinformation SCN into the

ASDU END OF GENERALINTERROGATION)

!V2.0

V5.D 30/01/02 Addition of orderCOM1/COM2/COM3/CO

M4 assignalble on theauxiliary relays.

Addition of the logic inputsAUX3 and AUX 4 do notgenrating alarm message.

Improvement of englishlabel

!V2.0

HARD V 4


9/12


Relay Type P122

SoftwareVersion

Date ofIssue



V5.F 08/08/02 EA approval option : logicalinput filtering on 24samples instead of 12either 15 ms at 50 Hz)

Improvment of theRecording of rollingdemand in ram saved. Theprevious version could leadto an untimely ram savederror message due to themanagement of this

recording

Courier improvment :adding of the cell 0010 (CBcontrol) protected bypassword

Correction of theconfiguration of taux3 andtaux4 for MODBUS

IEC103 : correction of thechecksum calculation for

short message. Correctionof the I0 channel data intothe disturbance record

!V2.0 HARD V 4


10/12


Page 8/10 MiCOM P120/P121/P122/P123






Relay Type P123

SoftwareVersion

Date ofIssue




Correction of al

encountered problem(answer to asynchronisation telegram,creation of a 2 secondstime out )

HARD V 2

HARD V 3

HARD V 4



Modbus time out of 200 msDisplay of the letter P in themenu N and N-1 whenpassword is active

!V2.0

V3.C 06/01/00 Label correction !V2.0

V3.D 06/04/00 Evolution of Modbus writing16 bits

!V2.0


!V2.0


HARD V 3

HARD V 4


11/12


Relay Type P123

SoftwareVersion

Date ofIssue



V4.E 31/01/01 Latch of the output relaysLatch of the auxiliary relays,relay by relay and not byfunction (like previously upto V3 version). On the otherhand the latch of the TRIPoutput relay remains byfunction. If the auxiliaryrelays are latched, an alarmwill be displayed. If the useracknowledges this alarm,

the auxiliary relays will bedelatched.DNP3 level 2 and 3

Addition of the tripping andclosing order for IEC103Phase rotation (ABC or

ACB)Third threshold algorithmfor improvement of thebehaviour on saturatedcurrent transformersTimer for the undercurrentfeature (0 to 150 sec)Tripping curves (rectifiercurve + LABORELLECcurves)Selection of the Settinggroup by level or by edge.CB fail detection (possibilityto inhibit the startingsignals)Instantaneous recordRolling demand

Peak value demandInstantaneous alarmsettable : self or not selfresetMatrix for the auto-recloser

Addition of a secondthreshold with definite timefor the I2 featureThe digital input can workwith AC signals (24 V to250 V AC)

Necessity to set in HMIConfiguration menu, thetype of voltage used, eitherACor DC .

!V2.0 HARD V 4


12/12


Page 10/10 MiCOM P120/P121/P122/P123

Relay Type P123

SoftwareVersion

Date ofIssue



V5.A 27/09/01 Maintenance mode formanual command of theoutput relays

Reset of leds by logic inputor control command orfront panel or on new faultappearance

!V2.0

V5.C 04/10/01 VDEW improvements

(Updating of theinformation SCN into the

END OF GENERALINTERROGATION ASDU)

!V2.0

V5.D 30/01/02 Addition of orderCOM1/COM2/COM3/COM4 assignalble on theauxiliary relays.

Addition of the logic inputsAUX3 and AUX 4 do notgenerating alarm message.

Improvement of english

label

!V2.0

HARD V4

V5.F 08/08/02 EA approval option : logicalinput filtering on 24samples instead of 12either 15 ms at 50 Hz)Improvment of theRecording of rollingdemand in ram saved. Theprevious version could leadto an untimely ram savederror message due to themanagement of thisrecordingCourier improvment :adding of the cell 0010 (CBcontrol) protected bypasswordCorrection of theconfiguration of taux3 andtaux4 for MODBUSIEC103 : correction of thechecksum calculation for

short message. Correctionof the I0 channel data intothe disturbance record

!V2.0 HARD V4

p12x_envcc55 hard-soft ware

Documents