OWNER’S MANUAL

ThePioneerEX is aneasy to use detector. The most difficultaspects of metal detecting have beenautomated.

However if you are new to the hobby, we stronglyrecommend that you:

1) Adjust the Sensitivity to a low setting in theevent of false signals. The detector powers on a3/4 sensitivity; increase to full sensitivity after you havebecome familiar with the detector.

2) Do not use indoors. This detector is for outdoor use only. Manyhousehold appliances emit electromagnetic energy, which caninterfere with the detector. If conducting an indoor demonstration,turn the sensitivity down and keep the search coil away fromappliances such as computers, televisions and microwave ovens.If your detector beeps erratically, turn off appliances and lights.

Also keep the search coil away from objects containing metal, such asfloors and walls.

3) Read this manual. Most importantly, review the Quick-Start Demo (p.6) and Basic Operation (p. 8-12).

4) Use 9-volt ALKALINE batteries only.Do not use Heavy Duty or ordinary Zinc-carbon Batteries.

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Quick-Start Demo . . . . . . . . . . . . . . . . . . . . . .6-7

Basic OperationPowering Up . . . . . . . . . . . . . . . . . . . . . . . .8The Display . . . . . . . . . . . . . . . . . . . . . .8-10

Operating Controls . . . . . . . . . . . . . . . . . . . . . .11

Environmental Conditions . . . . . . . . . . . . . . . .12

Audio Target Identification . . . . . . . . . . . . . . .13

Depth Select (Sensitivity Adjustment) . . . . . . .14

In The Field Techniques . . . . . . . . . . . . . . .15-17

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . .18

Metal Detecting Applications . . . . . . . . . . . . . .19

Treasure Hunter’s Code of Ethics . . . .Back CoverWarranty . . . . . . . . . . . . . . . . . . . . . . .Back Cover

The BOUNTY HUNTER PIONEER series of metal detectors is notassociated or connected in any way with Pioneer Corporation or itsPIONEER brand audio and video products or other products.

2

TABLE OF CONTENTS

3

TERMINOLOGYThe following terms are used throughout the manual, and are standardterminology among detectorists.

ELIMINATIONReference to a metal being "eliminated" means that the detector willnot emit a tone, nor light up an indicator, when a specified objectpasses through the coil’s detection field.

DISCRIMINATIONWhen the detector emits different tones for different types of metals,and when the detector "eliminates" certain metals, we refer to thisas the detector "discriminating" among different types of metals.Discrimination is an important feature of professional metaldetectors. Discrimination allows the user to ignore trash andotherwise undesirable objects.

RELICA relic is an object of interest by reason of its age or its associationwith the past. Many relics are made of iron, but can also be madeof bronze or precious metals.

IRONIron is a common, low-grade metal that is an undesirable target incertain metal detecting applications. Examples of undesirable ironobjects are old cans, pipes, bolts, and nails.Sometimes, the desired target is made of iron. Property markers,for instance, contain iron. Valuable relics can also be composed ofiron; cannon balls, old armaments, and parts of old structures andvehicles can also be composed of iron.

FERROUSMetals which are made of, or contain, iron.

PINPOINTINGPinpointing is the process of finding the exact location of a buriedobject. Long-buried metals can appear exactly like the surroundingsoil, and can therefore be very hard to isolate from the soil.

PULL-TABSDiscarded pull-tabs from beverage containers are the most bothersometrash items for treasure hunters. They come in many different shapesand sizes. Pull-tabs can be discriminated, but some other valuableobjects can have a magnetic signature similar to pull-tabs, and will alsobe eliminated when discriminating out pull-tabs.

GROUND BALANCEGround Balancing is the ability of the detector to ignore, or "seethrough," the earth’s naturally occurring minerals, and only sounda tone when a metal object is detected.

4

ASSEMBLYAssembly is easy and requires no tools.

●1 Position the lower stemwith the silver button toward the back.Using the bolt and knurled knob, attach the search coil to the plastic extensionprotruding from the lower stem.

●2 If your model is equipped with a3-piece stem, open theplastic locking nut onthe upper tube byrotating itcounterclockwise.Then slide the middletube into the uppertube, inserting the silverbutton into the locating holewhich is 1/2” behind the plasticlocking nut. Now tighten the plastic locking nut.

●3 Press the button on the upper end of the lower stem, andslide the lower stem into the upper stem.

Adjust the stem to a length that letsyou maintain a comfortable uprightposture, with your arm relaxed atyour side, and the search coilparallel to the ground in front of you.

●4 Wind the cable securely around thestem.

●5 Insert the plug into the matchingconnector on the right underside ofthe detector body. Be sure that thekey-way and pins line upcorrectly.

Caution: Do not force the plug in. Excessforce will cause damage.To disconnect the cable, pullon the plug.Do not pullon the cable.

Connectoron back ofcontrol housing

5

IMPORTANT: Always use ALKALINE batteries only.Do not use heavy duty batteries.

Always remove the batteries for prolonged storage.

CHECK THE BATTERIES if your detector exhibits any of the followingsymptoms:

●1 The unit does not turn on.

●2 Low speaker volume.

●3 Unit beeps continuously or erratically.

The LOW BATTERY indicator will come on and stay on if the batteriesare discharge. You may notice erratic beeping if using with LOWBATTERY illuminated.

IMPORTANT: Your Lone Star metal detector requires two 9-Volt ALKALINE batteries.

Follow these steps to install the batteries.

●1 Carefully remove the battery compartment door by pressing the releaseclip on the right side of the door.

●2 Snap one battery onto each of the terminals and place the batteries in-side the com-partment.Insert booth ofthe batterieswith terminalsfacing outward.

●3 Replace thecompartmentdoor by carefullyinserting oppo-site side of clipfirst. Then pressdown on clipside until batterydoor snaps intoplace.

BATTERIES

ReleaseClip

Both Batteriesteminalsfacing out

6

QUICK-START DEMONSTRATIONI. Supplies Needed

• A Medium-Size Nail • A Quarter• A Nickel • A Zinc Penny (dated after 1982)

II. Position the Detectora. Place the detector on a

table, with the search coilhanging over the edge.(or better, have a friendhold the detector, withthe coil off the ground)

b. Keep the search coilaway from walls, floors,and metal objects.

c. Remove watches, rings and other jewelry or metal objects fromhands and wrists.

d. Turn off appliances or lights that cause electromagneticinterference.

e. Pivot the search coil back toward the detector body.

III. Power UpPress the ON touchpad.The detector will beepseveral times and thesensitivity setting willbe indicated on theright of the display. Twoilluminated segmentsindicates 3/4 sensitivity.

IV. Wave each Object over the Search Coil (pass the flat side of the coinsparallel to the coil)a.Notice a different tone for each object.

Low Tone: NailMedium Tone: Nickel & Zinc PennyHigh Tone: Quarter

b.Motion is required. Objects must be in motion over the search coil to be detected.

7

V. Press the TARGET REJECTtouchpada. An “X” will appear under

the IRON segment.b. The “X” tell us that Iron

has been eliminated fromdetection.

VI. Wave the Nail over the Search Coila. The Nail will not be detected.b. The Nail has been "Discriminated Out."

VII. Wave the Quarter, Penny, and Nickel over the Search CoilThese non-ferrous objects will be detected with their owndistinctive tones.

VIII. Press the TARGET REJECT touchpad againAnother “X” will illuminate under “AL ZN”.

IX. Wave all objects over the Search Coil

The Zinc Penny will not be detected. make sure the penny is post-1982; these are made of Zinc. CAUTION: some zinc pennieswithin 1/2” of the coin surface will induce a high tone.

X. Press the TARGET REJECT touchpad againa. A third “X” appears.b. Pass all object over the search coil.The nail, penny, and nickel are all eliminated from detection.

XI. Press the TARGET REJECT touchpad to return the detector to all-metals detection, with no “X”s illuminated.

QUICK-START DEMONSTRATION (continued)

8

BASIC OPERATIONPOWERING UPPress the ON touch pad.All display indicators will illuminate momentarily

The inverted-pyramid depth-selection indicator on the right of thedisplay will stay illuminated.

UNDERSTANDING THE DISPLAY●1 DEPTH SELECT

The detector default to 3/4sensitivity, indicated bytwo illuminated segments.To change the depth rangeof the detector, and thus itssensitivity to more deeplyburied objects, use theDEPTH SELECT touch pad.each touch of DEPTHSELECT toggles the detector among three different sensitivity settings.The detector is at maximum depth capability when three depthsegments are illuminated on the right of the display.

At the maximum depth setting, the detector will detect a coin-sizedobject buried approximately 6 1/2 inches beneath the surface. Withtwo depth segments illuminated, the detector’s depth range will bereduced to 80%, and with one depth segment illuminated, the rangewill be reduces to 65%.A more detailed explanation of depth selection is found on page 14.

●2 LOW BATTERYThe LOW BATTERYindicator will illuminatewhen the 9-volt batteriesare discharged to a levelof 6.8 volts.

Replace the batteries assoon as possible afterreceiving th e low batteryindication. The detector

9

will begin to beep erratically and operate unreliably if continuing usewith discharged batteries.To save on batteries, check each battery individually, as the twobatteries can discharge at different rates. When LOW BATTERYilluminates, it is possible that only one of the batteries requiresreplacement.

Under normal conditions, a set of batteries will last for approximately16 hours in the field, depending upon the brand of battery.

●3 PROBABLE TARGET

The four categories depicted across the top of the displayindicate the probable identification of buried, detected metalobjects. The search coil must be in motion over an object tobe detected. Alternatively, you can pass an object over amotion less search coil to test your detector. One of the fourtarget indicators will illuminate, indicating the probableidentif ication of the object. The indicator will remainilluminated until another object is detected.

You will encounter a never-ending variety of buried metalobjects. It is therefore impossible to accurately identify allburied metal objects. The target identification system willaccurately identify the most common items.

BASIC OPERATION continued

10

Commonly-found object are classified into the four categoriesas follows:

IRON ------------------------------------------------Ferrous objectsMetals composed mostly or entirely of ironMost very small metals objectsSmall foil pieces; small gold pieces.

AL ZN ------------------------------------------------Post-1982 pennies (are made of zinc, some zinc pennies

will register as coins within 1” of the coil)Zinc coins, such as recent foreign currencyMost bottle screw capsLarge foil piecesMany rings; most gold ringsOlder pull-tabs (those which detach from the can)

AL 5¢ ------------------------------------------------Large gold ringsNewer pull-tabs (those which stay connected to can)NickelsLarge Aluminum Pieces

COINS ------------------------------------------------Silver coins, like dimes and quartersCopper pennies (pre-1982)Very large metal objects like manhole covers.

●4 REJECTED TARGETWhen “X” appears under a targetcategory, objects falling into thiscategory are eliminated fromdetection. This feature iscommonly referred to as targetdiscrimination.

With each press of the REJECTTARGET touch ad, you willprogressively eliminate, fromleft to right, the common, less desirable, targets. When all three “X”are illuminated, the next press will erase all “X”s, returning thedetector to all-metal detection status, where all types of metals willbe detected.

BASIC OPERATION continued

11

BASIC OPERATION continuedOPERATING CONTROLSThe Pioneer EX is the most automated, easy-to-operate, professionalmetal detector ever designed. It is designed for those who are new to thehobby providing maximum basic target discrimination, while requiringminimal operator adjustment.

DEPTH SELECTWith each press of the DEPTHSELECT touch pad, the detectortoggles among three differentdepth-detection levels. Each ofthese sensitivity levels isidentified through the 3-segmentdepth-select icon on the right ofthe display.

When three segments are illuminated, the detector is at maximumsensitivity. As you press the DEPTH SELECT touch pad, the detectortoggles among the three different sensitivity levels. A more detailedexplanation of depth selection is found on page 14.

TARGET REJECTUpon power-up, all types ofmetals are detected. The TARGETREJECT touch pas allows the userto eliminate undesirable metalsfrom detection.

With each press of the REJECTTARGET touch pad, unwantedmetals are progressivelyeliminated, from left to right on the display. When all three “X”s areilluminated, the next press will erase all “X”s, returning the detector to all-metal detection status, where all types of metals will be detected.

12

BASIC OPERATION continuedENVIRONMENTAL CONDITIONSWATER HUNTING: Your Pioneer EX is ideal for damp grass and shallowwater spots. the search coil is waterproof; the case and case-to-cableconnection is not. Be careful to keep the detector body dry.

In saltwater, keep the search coil from contact with the ground. Contactwith saltwater sands will cause the detector to beep falsely. For bestresult in saltwater, eliminate IRON to reduce false signals caused byconductive beach sands. Coil sweep technique is also important insaltwater; keeping the coil submerged is better than dunking and lifting.The detector needs time to readjust to the conductive salt water.

RED CLAY: The red clay earth found in the southwestern U.S. mayrequire a reduction in the DEPTH SELECT level if encountering falsesignals. Coil sweep technique is also more critical in red clay; keep thecoil level with the ground. Do not lift the coil at the ends of your sweep.Review coil sweep technique on page 15.

RED SANDS: Red sand found in desert locations will react like red clays,so fallow the same precautions as outlined in the paragraph above.

BLACK SANDS: The most promising gold prospecting locations cancontain large amounts of black sand. This black sand is the mostdemanding detecting environment, and frequently requires a detectorcosting thousands of dollars for the best results. Your Pioneer EX will stillfunction in these conditions, but will usually require operation at reducedsensitivity levels. If you receive constant false signals, reduce thesensitivity or move to another area.

SAND: Dry beach sands are no problem for the Pioneer EX. if the sandis damp with saltwater, however, follow the precautions outlined undersaltwater above.

HOT AND COLD: Be patient if moving immediately between hot andcold environments, like taking your detector from your air-conditionedhome into a blazing summer sun. The search coil is constructed ofcopper wire which will expand and contract with temperature change.Your detector may require 10 to 15 minutes to stabilize to the ambienttemperature.

13

AUDIO TARGET IDENTIFICATIONWhile the LCD (Liquid Crystal Display) is very accurate in identifyingburied objects, the user in the field does not always maintain the displayscreen in his field of vision. Therefore, we have incorporated an audiofeedback mechanism to alert the user to the nature of buried objects.This audio feedback system first alerts the user to the presence andclassification of objects, whose nature and location can be confirmedusing the LCD display.

The detector will sound one of three different tones, depending on thetype of metal detected.

BASS TONEFerrous objects, such as iron and steel, will induce a bass tone.The smallest gold objects can also induce a bass tone.

MEDIUM TONEPull-tabs, newer pennies (post-1982), larger gold objects, zinc,small brass objects, and most bottle screw caps will inducemedium tones. Many recent vintage foreign currencies willinduce medium tones. Medium tone objects will illuminate thetwo center target indicators.

HIGH TONESilver and copper coins, larger brass objects, older pennies (pre-1982), and highly oxidized metals will induce high tones.Quarters, dimes and other precious coins fall into this category.

Audio Target Identification (ATI) classifies metals into four categories.

LOW TONE

Nails, Bottle Caps,& Smaller Gold

MEDIUM TONE

Old & New Pull Tabs, ZincPennies (Post 1982), Nickel,

Larger Gold Objects

HIGH TONE

Copper, Silver & BrassCopper Pennies (Pre 1982)

14

DEPTH SELECT (Sensitivity Adjustment)Upon power-up, the detector defaults to 3/4 sensitivity. To increase to fullsensitivity, press the DEPTH SELECT touchpad once.

ELECTROMAGNETIC INTERFERENCEThe principle use for the Sensitivity Control is to eliminateElectromagnetic Interference (EMI).A hobby metal detector is an extremely sensitive device; the search coilcreates its own magnetic field and acts like an antenna. If your detectorbeeps erratically when the search coil is motionless, the unit is probablydetecting another electromagnetic field.

Common sources of EMI are electric power lines, both suspended andburied, motors, and household appliances like computers andmicrowave ovens. Some indoor electronic devices, such as dimmerswitches used on household lighting, produce severe EMI and can causethe detector to beep erratically. Other metal detectors also produce theirown electromagnetic fields; so if detecting with a friend, keep two metaldetectors at least 20 feet apart.

If the detector beeps erratically, REDUCE THE SENSITIVITY by using theDepth Select Control.

SEVERE GROUND CONDITIONSA secondary use for the Sensitivity Control is to reduce false detectionsignals caused by severe ground conditions. While your Pioneer EXcontains circuitry to eliminate the signals caused by most naturallyoccurring ground minerals, 100% of all ground conditions cannot beanticipated. Highly magnetic soils found in mountainous and gold-prospecting locations can cause the detector to emit tones when metalobjects are not present. High saline content soils and sands can alsocause the detector to false.

If the detector emits false, non-repeatable, signals, REDUCE THESENSITIVITY.

MULTIPLE TARGETSIf you suspect the presenceof deeper targets beneath ashallower target, reduce thesensitivity to eliminate thedetection of the deepertargets, in order to properlylocate and identify theshallower target.

15

IN THE FIELD TECHNIQUES

When pinpointing a target, try drawing an “X”,as illustrated, over where the tone is induced.

PINPOINTING

Accurate pinpointing takes practiceand is best accomplished by“X-ing” the target area.

1. Once a buried target is indicatedby a good tone response,continue sweeping the coil overthe target in a narrowingside-to-side pattern.

2. Take visual note of the place onthe ground where the “beep”sounds.

3. Stop the coil directly over thisspot on the ground.

4. Now move the coil straightforward and straight backtowards you a couple of times.

5. Again make visual note of thespot on the ground at whichthe “beep” sounds.

6. If needed, “X” the target atdifferent angles to “zero in” onthe exact spot on the ground atwhich the “beep” sounds.

COIL MOVEMENT

When swinging the coil, becareful to keep it level with theground about 1/2 inch from thesurface. Never swing the coil likea pendulum.

TARGET DEPTH ESTIMATION

After verifying a desirabletarget, pass the coil again, butraise the coil 1” over theground, progressively higherwith each sweep. Note the coilelevation at which the signaldisappears. With practice, youwill be able to approximatetarget depth.

WRONG

CORRECT

16

Swing the search coil slowly,overlapping each sweep as youmove forward. It is important tosweep the coil at a consistent speedover the ground as you search.After identifying a target, yoursweep technique can help inidentifying both the location and thenature of the target. If youencounter a weak signal, trymoving the coil in short, rapidsweeps over the target zone; such a

short rapid sweep mayprovide a more consistent

target identification.

Most worthwhileobjects will respond

with a repeatabletone. If the

signal does notrepeat after

sweepingthe coil

directlyover the

suspected target a few times, it ismore than likely trash metal.

Crossing the target zone withmultiple intersecting sweeps atmultiple angles is another way toverify the repeatability of the signal,and the potential of the buriedtarget. To use this method, walkaround the target area in a circle,sweeping the coil across the targetrepeatedly, every 30 to 40 degreesof the circle, about ten differentangles as you walk completelyaround the target. If a high-tonetarget completely disappears fromdetection at a given angle, chancesare that you are detecting oxidizedferrous metals, rather than a silveror copper object. If the tonechanges at different angles, youmany have encountered multipleobjects. If you are new to thehobby, you may want to dig alltargets at first. With practice in thefield, you will learn to better discernthe nature of buried objects by thenature of the detector’s response.

IN THE FIELD TECHNIQUES (continued)

WHATREADSLIKE THIS

…MAYACTUALLYBE THIS

17

You may encounter some falsesignals as you proceed. Falsesignals occur when the detectorbeeps, but no metal target ispresent. False signals can beinduced by electromagneticinterference, oxidation, or highlymineralized ground soils. If thedetector beeps once, but does notrepeat the signal with severaladditional sweeps over the samespot, there is probably no targetpresent.

When searching very trashingground, it is best to scan smallareas with slow, short sweeps.You will be surprised just howmuch trash metal and foil you willfind in some areas. The trashiestareas have been frequented by themost people, and frequently holdthe most promise for finding themost lost valuables. To make

searching easier in very trashyareas, consider purchasing theBounty Hunter 4-inch Search Coil.The 4-inch coil’s narrowerdetection field can betterdistinguish between two objects inclose proximity.

Also maintain the search coilpositioned just above the surfaceof the ground, without makingcontact with the ground. Makingcontact with the ground can causefalse signals.

IN THE FIELD TECHNIQUES (continued)

USING HEADPHONESUsing headphones (not supplied) improves battery life, and prevents thesounds from annoying bystanders.It also allows you to hear subtle changes in the sound more clearly,particularly if searching in a noisy location. For safety reasons, do not useheadphones near traffic or where other dangers are present. This device isto be used with interconnecting cables/headphone cables shorter than threemeters.

18

TROUBLE SHOOTING GUIDESYMPTOM CAUSE SOLUTION

Detector chatters • Using detector • Use detectoror beeps erratically indoors outdoors only

• Using detector near • Move away power lines from power lines

• Using 2 detectors in • Keep 2 detectorsclose proximity at least 20’ apart

• Highly oxidized • Only dig upburied object repeatable

signals• Environmental • Reduce sensitivity

electromagnetic until erratic interference signals cease

Constant low tone • Discharged batteries • Replace batteriesor constant repeatingtones • Wrong type of • Use only 9V

batteries alkaline batteries

LCD does not lock • Multiple targets • Move coil slowlyon to one target ID present at different anglesor detector emits • Highly oxidizedmultiple tones target

• Sensitivity set • Reduce sensitivitytoo high

No power, no • Dead batteries • Replace batteriessounds • Poor battery • Check connections

contact• Cord not connected

securely

TROUBLE SHOOTING

19

METAL DETECTING APPLICATIONSCOIN SHOOTING:The most popular metal detecting activity.Find coins where people congregate frequently. Many detectorists revisit thesame areas again and again to find a never-ending treasure trove as peoplecontinue to lose valuables every day. Parks, fairgrounds, and play ares aregood choices. The most valuable old coins are frequently found in abandonedhome sites, or if you live on an older property, maybe in your own backyard.

Control settings required. Target-Rejected al least 2-Xs to eliminate iron,foil, and old pull tabs. Target-Rejected all 3-Xs if you want to find onlycopper and silver. If you search for nickels, remember that you will alsoencounter some newer pull-tabs. Some newer pull-tabs have a magneticsignal indistinguishable from nickel.

RELIC HUNTING:The most effective relic hunting is best accomplished after conducting historicalresearch. Visit your local library, or check the internet, for historical events inyour area. You can target specific areas and gain valuable insight into your localhistory. Remember to ask permission and respect laws regarding private andgovernment property.

Control settings required. No X’s should be displayed. Do notdiscriminate out any types of metals as many of the oldest relics containiron.

JEWELRY HUNTING:This is the most challenging treasure hunt. Gold rings will register in the samerange as pull-tabs. Necklaces will register with zinc and foils. You will dig upmany trash items in your search for jewelry, but jewelry hunting holds themost potential for reward. Please pick up ant throw away those pull-tabs tohelp clean the environment.

Control settings required. Target-Reject only the 1st X; eliminate IRONonly.

JEWELRY HUNTING:A cache, pronounced “cash,” is a buried or hidden valuable stored inside acase, can, strong gox, or bag. A cache could be the loot from a bank robberyor someone’s life savings. Caches can be hidden in floors or walls of an oldhouse, or buried nearby.

Control settings required. No X’s should be display. The containerholding the treasure will frequently be a ferrous object, so you want todetect all types of metal objects.

TREASURE HUNTER’S CODE OF ETHICS:• Always check Federal, State, County and local laws before searching.• Respect private property and do not enter private property without the owner’s permission.• Take care to refill all holes and try not to leave any damage.• Remove and dispose of any and all trash and litter found.• Appreciate and protect our inheritance of natural resources, wildlife and private property.• Act as an ambassador for the hobby, use thoughtfulness, consideration and courtesy at all times.• Never destroy historical or archaeological treasures.• All treasure hunters may be judged by the example you set; always conduct yourself with

courtesy and consideration of others

First Texas Products, LLC1465-H Henry Brennan

El Paso, TX 79936(915) 633-8354 MEXB 070109

Copyright© 2009 by First Texas Products, L.L.C.

All rights reserved, including the right to reproduce this book, or parts thereof, in any form.

Published by First Texas Products, L.L.C.

Bounty Hunter® is a registered trademark of First Texas Products, L.L.C.

The BOUNTY HUNTER PIONEER series of metal detectors is not associated or connected in any waywith Pioneer Corporation or its PIONEER brand audio and video products or other products

www.detecting.com

FIRST TEXAS PRODUCTS, LLC1-YEAR LIMITED WARRANTY

The Bounty Hunter Pioneer Ex is warranted against defectsin workmanship or materials under normal use for one year

from date of purchase to the original user. Liability in allevents is limited to the purchase price paid. Liability under

this Warranty is limited to replacing or repairing, at ouroption, any Bounty Hunter Detector returned, shipping cost

prepaid, to First Texas Products, LLC. Damage due toneglect, accidental damage or misuse of this product is not

covered by this warranty.

Proof of purchase is required to make a claim under this warranty.

NOTE TO FOREIGN COUNTRY CUSTOMERSThis warranty may vary in other countries, check with your distributor for details.

Factory warranty follows the channel of distribution.Warranty does not cover shipping costs.