original bmw accessories. installation instructions › attachments › x5-e70-forum ›...
TRANSCRIPT
-
Original BMW Accessories. Installation Instructions��
Mud flaps retrofit BMW X5/ X5M (E70)
Retrofit kit no.:
Installation time
82 16 0414673 82 16 0 41 6 162 82 1 6 0 41 6 1 61 82 16 0 428 284 82 16 0 41 4 67 4 82 16 0 420 836 82 16 0 41 6 163 82 16 0 430 714 82 16 0 430 713 82 16 0 428 644 82 16 0428 281
Front mud flaps kit 1811/1911 without step Front mud flaps kit 2011/21 11 with step Front mud flaps kit 2011/2111 without step Front mud flaps kit X5M and M Sport package Rear mud flaps kit 1811/1911 Rear mud flaps kit 2011 with Aero package Rear mud flaps kit 2011 without Aero package Rear mud flaps kit 2111 with Aero package Rear mud flaps kit 21 11 without Aero package Rear mud flaps kit 21 11 with M Sport package Rear mud flaps kit X5M
The installation time is around 0.5 hours per axle, although this may vary depending on the condition of the car and the equipment in it.
In general the car must be upgraded to the latest I stage status by flashing before starting the conversion work.
Differing programming times may be necessary depending on the production age of the vehicle and on work previously performed on the vehicle.
The installation time specified does not include the time spent on programming/coding.
The calculation of the total costs for the programming time must be factored into the calculation of retrofitting costs (no invoicing via warranty).
Important information The rear mud flaps for 18" /19" wheels cannot be installed in conjunction with the special accessories Aero package.
These installation instructions are primarily designed for use within the BMW dealership organisation and by authorised BMW service companies.
In any event, the target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge.
All work must be completed using the latest BMW repai r manuals, circuit diagrams, servicing manuals and work instructions, in a rational order, using the prescribed tools (special tools) and observing current safety regulations.
©BMW AG, Munich 01 29 0418179 0512009 (VIZ)
-
If you experience installation or function problems, restrict troubleshooting to approx. 0.5 hours for mechanical work and 1 .0 hour for electrical work.
To avoid unnecessary extra work and/or costs, an inquiry is to be sent straight away to the technical parts support via the Aftersales Assistance Portal (ASAP). Specify the following information: - Chassis number, - Part number of the retrofit kit, - A precise description of the problem, - Work steps already carried out.
Do not archive the hard copy of these installation instructions since daily updates are provided via ASAP!
All pictures show LHD cars; proceed accordingly on RHD cars.
Pictograms
[2 Denotes instructions that draw your attention to special features. � Denotes the end of the instruction or other text.
Installation information
Some of the installation is shown only on the left-hand side of the car, proceed in the same way on the right-hand side of the car.
Bonding surfaces must be cleaned with a cleaner and must be free from grease. The ambient temperature for bonding must be no lower than 15 °C and no higher than 35 °C. The car may be driven after approx. 6 hours and may be taken through a car wash after 48 hours.
Special tools required
None
©BMW AG, Munich 01 290418179 05/2009 (VIZ) 2
-
Table of contents
Section Page
1. Front mud flaps all 2011/21 11 parts list, M Sport package and X5M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Front mud flaps 1811/1911 parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Rear mud flaps 1811/1911 parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. Rear mud flaps 2011/2111 without Aero package parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Rear mud flaps 2011/2111 with Aero package parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6. Rear mud flaps kit 2111 with M Sport package parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. Rear mud flaps kit X5M parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8. Preparatory work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
9. Fitting the front mud flaps 1811/1911 without step . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
10. Fitting the front mud flaps 1811/1911 with step . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
11. Fitting front mud flaps 2011/2111, M Sport package and X5 M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
12. Fitting rear mud flaps 1811/1911 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 21
13. Fitting rear mud flaps 2011/21 11 without Aero package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
14. Fitting rear mud flaps 2011/21 11 with Aero package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
15. Fitting rear mud flaps 2011/21 II with M Sport package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
16. Fitting rear mud flap X5M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
17. Concluding work and coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
©BMW AG, Munich 01 29041 8179 05/2009 (VIZ)
-
1. Front mud flaps all20"/2 1" parts list, M Sport package and X5M
Legend
A Left mud flap
B Right mud flap
C Expanding rivet (8 x) (for 20"/21" only: 10 x)
D Self-tapping screw 4.8x22 (2 x)
AF Primer (not included in the M Sport package and X5M parts kit)
AG Cleaning cloth (not included in the M Sport package and X5M parts kit)
©BMW AG, Munich 01 29 0418179 05/2009
0700305 v
(V/Z)
-
2. Front mud flaps 18" / 19" parts list
Legend
E Left mud flap
F Right mud flap
G Expanding rivet (8 x)
H Self-tapping screw 4.8x22 (2 x)
I Self-tapping screw (4 x) (only required for step)
©BMW AG, Munich 01 29041 8179
0700104 v
05/2009 (VIZ)
-
3. Rear mud flaps 18" / 19" parts list
Legend
J Left mud flap
K Right mud flap
L Expanding rivet (2 x)
©BMW AG, Munich 01 290418179
M Screw 4.8x22 (4 x)
N Sheet metal nut 4.8 (2 x)
0 Self-tapping screw (4 x)
05/2009
070 0041 v
(VIZ) 6
-
4. Rear mud flaps 20"/2 1" without Aero package parts list
Legend
P Left mud flap
Q Right mud flap
R Expanding rivet (6 x for 20"), (8 x for 21 ")
S Screw 4.8x22 (14 x)
© BMW AG, Munich 01 290418179
T Sheet metal nut 4.8 (1 0 x)
AF Primer
AG Cleaning cloth
05/2009
0700306V
(V/Z)
-
5. Rear mud flaps 20"/2 1" with Aero package parts list
Legend
U Left mud flap
V Right mud flap
W Expanding rivet (6 x) (8 x for 21 ")
X Screw 4.8x22 (12 x)
©BMW AG, Munich 01 29 0418179
Y Sheet metal nut 4.8 (1 0 x)
AF Primer
AG Cleaning cloth
05/2 009
0700307V
(ViZ) 8
-
6. Rear mud flaps kit 2 1" with M Sport package parts list
Legend
Z Left mud flap
AA Right mud flap
AB Expanding rivet (4 x)
©BMW AG, Munich 01 290418179
E\ @
AC Screw 4.8x22 (16 x)
AD Sheet metal nut 4.8 (1 0 x)
AE Sheet metal nut (2 x)
05/2009
0700290V
(VIZ)
-
7. Rear mud flaps kit X5M parts list
Legend
BA Left mud flap
BB Right mud flap
BC Expanding rivet (8 x)
©BMW AG, Munich 01 290418179
E\ ®
B D Screw 4.8x22 (12 x)
BE Sheet metal nut 4.8 (1 0 x)
BF Self-tapping screw (2 x)
05/2009
0700370V
(VIZ) 10
-
8. Preparatory work
ISTA No.
Conduct a brief test
The following components must be removed first (only when installed at the rear)
Rear wheel left and right 36 10 300
©BMW AG, Munich 01 290418179 0512009 (VIZ) 11
-
9. Fitting the front mud flaps 18" / 19" without step
0700049V
0700054 v
0700324 v
©BMW AG, Munich 01 290418179
Turn the steering all the way to the left.
Remove the existing blind rivets (1) as they are no longer needed.
Remove the existing screw (1) as it is no longer needed.
[3 Bonding surfaces must be cleaned with a cleaner and must be free from grease.�
Peel back the protective film (1) on the adhesive strip approximately 20 mm from the mud flap E.
Completely remove the protective film (2).
05/2009 (VIZ) 12
-
0700325V
070031 7 V
0 1 290418179
Position the mud flap E and secure with expanding rivets G.
Secure mud flap Eat the bottom using screw H.
Remove the protective film (1) from the adhesive strip on mud flap E.
Press mud flap E along its outer contour on the side wall.
0512009 (V/Z) 13
-
,--1 I
�:
©BMW AG, Munich
0700328V
0700329V
01 290418179
� Do not exceed the drilling depth since otherwise you may damage the car.�
Create a hole (1) of diameter 6 mm maintaining a maximum drill depth of 5 mm.
Then position the expanding rivet G.
� Do not exceed the drilling depth since otherwise you may damage the car.�
Turn the steering all the way to the right.
Create a hole (1) of diameter 6 mm maintaining a maximum drill depth of 5 mm.
Then position the expanding rivet G.
0512009 (VIZ) 14
-
1 O.Fitting the front mud flaps 18"119" with step
0700054 v
0700093V
©BMW AG, Munich 01 290418179
Turn the steering all the way to the left
Remove the existing blind rivets (1) as they are no longer needed.
Remove the existing screw (1) as it is no longer needed.
[!2] Bonding surfaces must be cleaned with a cleaner and must be free from grease.�
Peel back the protective film (1) on the adhesive strip approximately 20 mm from the top end of mud flap E.
Completely remove the protective film (2).
0512009 (VIZ) 15
-
0700098V
0700056V
01 2 9 0418179
Position the mud flap E and secure with expanding rivets G.
Screw self-tapping screws I into mud flap E.
Secure mud flap E with screw H through hole (1 ).
Remove the protective film (1) from the adhesive strip on mud flap E.
05/2009 (VIZ) 16
-
/ / /
�
I I I
�j
©BMW AG, Munich
070 0057 v
0700053V
0700055 v
01 290418179
Press mud flap E along its outer contour on the side wall.
� Do not exceed the drilling depth since otherwise you may damage the car. �
Create a hole (1) of diameter 6 mm maintaining a maximum drill depth of 5 mm.
Then position the expanding rivet G.
� Do not exceed the drilling depth since otherwise you may damage the car.�
Turn the steering all the way to the right.
Create a hole (1) of diameter 6 mm maintaining a maximum drill depth of 5 mm.
Then position the expanding rivet G.
0512009 (VIZ) 17
-
1 1.Fitting front mud flaps 20"/2 1 " , M Sport package and X5M
0700371 v
070031 3V
0700308V
0700050V
Turn the steering all the way to the left.
Remove the existing blind rivets (1) as they are no longer needed.
ForM Sport package and XSM only:
Remove the existing blind rivet (2) as it is no longer needed.
For all cars except M Sport package and XSM:
Position mud flap A. Trace the contours of mud flap A using a water-soluble pen (1 ). Then remove mud flap A again.
Clean the surface (1) within the marked contour thoroughly with the enclosed cleaning cloth AG and allow to dry. []2] Do not apply primer AF outside the drawn-on
contours.�
Then apply primer AF using the enclosed primer pad.
Remove the line made by the water-soluble pen.
For all cars:
Remove the existing screw (1) as it is no longer needed.
05/2009 (VIZ) 18
-
0700107V
0700372V
0700096 v 01 2 9 0418179
Peel back the protective film (1) on the adhesive strip approximately 20 mm from the top end of mud flap A.
Completely remove the protective film (2).
If necessary, peel back the protective film (3) on the adhesive strip approximately 20 mm from the top end of mud flap A.
Position the mud flap A and secure with expanding rivets C.
ForM Sport package and X5M only:
Also secure mud flap A in hole (1) using an expanding rivet C.
For all cars:
Secure mud flap A at the bottom using screw D.
Remove the protective film (1) from the adhesive strip on mud flap A.
0512009 (VIZ) 19
-
'
©BMW AG, Munich
/ /
�
I I I
0700097V
0700095 v
0700106V
0700067 v 01 29 0418179
Press mud flap A along its outer contour on the side wall.
[2j Do not exceed the drilling depth since otherwise you may damage the car.�
Create a hole (1) of diameter 6 mm maintaining a maximum drill depth of 5 mm.
Then position the expanding rivet C.
[2j Do not exceed the drilling depth since otherwise you may damage the car.�
Turn the steering all the way to the right.
Create a hole (1) of diameter 6 mm maintaining a maximum drill depth of 5 mm.
Then position the expanding rivet C.
For all cars except M Sport package and X5M:
[2j Do not exceed the drilling depth since otherwise you may damage the car. �
Create a hole (1) of diameter 6 mm maintaining a maximum drill depth of 5 mm.
Then position the expanding rivet C.
0512009 (VIZ) 20
-
12.Fitting rear mud flaps 18" / 19"
0700042V
0700043V
0700059V
0700321 v 01 290418179
For all cars:
Remove the existing blind rivet (1) as it is no longer needed.
Remove the existing screw (1) as it is no longer needed.
Cut the internal surface of the bumper trim in the area shown (1 ).
[3 Bonding surfaces (1) must be cleaned with a cleaner and must be free from grease. �
05/2009 (VIZ) 21
-
0700044 v
0700086V
0700045 v
070 0047 v ©BMW AG, Munich 01 290418179
Remove the protective film (1) from the adhesive strip approximately 20 mm from mud flap J.
Completely remove the protective film (2).
Secure mud flap J to hole (1) using screw M.
Position mud flap J, push it upwards and secure in place with expanding rivet L.
Secure mud flap J using self-tapping screws 0.
05/2009 (VIZ) 22
-
0700046V
0700062V
[I] . .
0700063V
©BMW AG, Munich 01 290418179
Create a hole (1) of diameter 5 mm.
Introduce sheet metal nut N behind the wheel arch (1).
Secure the tab of mud flap J using screw M and sheet metal nut N.
Remove the protective film (1) from the adhesive strip on mud flap J.
Press mud flap J along its outer contour on the side wall.
05/2009 (VIZ) 23
-
1 3.Fitting rear mud flaps 20"/2 1" without Aero package
0700309V
0700075 v
070031 4V
©BMW AG, Munich 01 29 0418179
Remove the existing blind rivets (1) as they are no longer needed.
Only for cars with 21 ":
also remove blind rivet (2) as it is no longer needed.
For all cars:
Remove the existing screws (1) as they are no longer needed.
Cut the internal surface of the bumper trim in the area shown (1 ) .
Position mud flap P.
Trace the contours of mud flap P using a water-soluble pen (1 ). Then remove mud flap P again.
05/2009 (VIZ) 24
-
070031 8V
0700070V
0700071 v
I[5J Do not apply primer AF outside the drawn-on LlCJ contours.�
Clean the bonding surface (1) on and in the wheel arch within the marked contour thoroughly with the enclosed cleaning cloth AG and allow to dry.
Then apply primer AF using the enclosed primer pad.
Remove the line made by the water-soluble pen.
[21 Only place the expanding rivets R in position, do not lock them.�
Position mud flap P and hold in place with expanding rivets R.
Mark out the drill holes (1) on mud flap P in the wheel arch.
Then remove mud flap P again.
Create a hole (1) of diameter 5 mm.
Below the four outer holes (1 ) , create cuts (approx. 1 0 mm) for the sheet metal nuts T using a knife.
Insert four sheet metal nuts T into the drill holes.
05/2009 (V/Z) 25
-
0700069V
0700310V
0700073 v ©BMW AG, Munich 01 290418179
Completely remove the protective film (1) on the adhesive strip, and remove the protective film (2) on the adhesive strip approx. 20 mm from mud flap P.
Reposition mud flap P and secure with expanding rivets R.
Only for cars with 21 ":
Also secure mud flap P using expanding rivet R at point (2).
For all cars:
Introduce sheet metal nut T behind the wheel arch (1 ).
Secure mud flap P using self-tapping screws S.
Secure mud flap P using screws S from underneath.
05/2009 \VIZ) 26
-
©BMW AG, Munich
0700076V
[I] . .
070007 7 V
01 29 0418179
Remove the protective film (1) from the adhesive strip on mud flap P.
Press mud flap P along its outer contour on the side wall.
05/2009 (VfZ) 27
-
1 4. Fitting rear mud flaps 20" /2 1 " with Aero package
0700092V
0700105V
0700311 v
0700059V
01 290418179
Remove both side sections (1) and side section supports for the Aerodynamic package as per installation instructions 0129 0417 827.
Cut the side section (1) in the area shown on the scribed line.
Cut the side section support (1) of the Aerodynamic package in the area shown.
Remove the existing blind rivets (1) as they are no longer needed.
Only for cars with 21 ":
also remove blind rivet (2) as it is no longer needed.
For all cars:
Cut the internal surface of the bumper trim in the area shown (1 ).
Reinstall the side section and side section support of the Aerodynamic package as per installation instructions 01 29 0 417 827.
05/2009 (VIZ) 28
-
070031 6V
070031 8V
0700080V
0700081 v ©BMW AG, Munich 01 290418179
Position mud flap U.
Trace the contours of mud flap U using a water-soluble pen. Then remove mud flap U again.
Clean the bonding surface (1) on and in the wheel arch within the marked contour thoroughly with the enclosed cleaning cloth AG and allow to dry.
IJ:2l Do not apply primer AF outside the drawn-on contours.�
Then apply primer AF using the enclosed primer pad.
Remove the line made by the water-soluble pen.
1]51 Only place the expanding rivets W in position, do not ll::J lock them. �
Position the mud flap U and secure with expanding rivets W.
Mark out the drill holes (1) on mud flap U in the wheel arch.
Then remove mud flap U again.
0512009 (VIZ) 29
-
070007 8V
0700312V
©BMW AG, Munich
Create a hole (1) of diameter 5 mm.
Below the four outer holes (1 ), create cuts for the sheet metal nuts Y using a knife.
Insert four sheet metal nuts Y into the drill holes.
Remove the protective film (1) on the adhesive strip approximately 20 mm from the mud flap U.
Completely remove the protective film (2).
Re-position the mud flap U and secure with expanding rivets W.
Only for cars with 21 ":
Also secure mud flap U using expanding rivet W at point (2).
For all cars:
Introduce sheet metal nuts Y behind the wheel arch (1 ).
Secure mud flap U using self-tapping screws X.
05/2009 (VIZ) 30
-
15.Fitting rear mud flaps 20"/2 1" with M Sport package
0700292V
0700291 v
0700382V
0700295 v
Cut the interior trim of the bumper trim in the area shown (1 ), taking note of the free space behind the mud flap.
Remove the existing blind rivets (1) as they are no longer needed.
Remove the existing screws (1) as they are no longer needed.
Remove the wheel housing extension (1 ) .
05/2009 (V/Z) 32
-
©BMW AG, Munich
I I I
j ® 0700083V
0700084 v
[j] .
. . . .
0700085 v
01 290418179
Secure mud flap U using screw X from underneath.
Remove the protective film (1) from the adhesive strip on mud flap U.
Press mud flap U along its outer contour on the side wall.
0512009 (VIZ) 31
-
0700296V
0700297 V
Using a suitable tool, create the cut-out for the sheet metal nuts AE on the centre securing hole (1) with the dimensions specified.
Place sheet metal nut AEon the centre securing hole (1) on the wheel arch cover.
Then reinstall the wheel housing extension (2).
IJ5I Only place the expanding rivets AB in position, do not Ll:::::J lock them.�
Position mud flap AA and hold in place with expanding rivets AB and screw AC.
Mark out the drill holes (1) on mud flap AA in the wheel arch.
Then remove mud flap AA again.
Create a hole (1) of diameter 5 mm.
Below the four outer holes (1 ), create cuts (approx. 1 0 mm) for the sheet metal nuts AD using a knife.
Insert four sheet metal nuts AD into the drill holes.
05/2009 (V/Z) 3 3
-
0700300V
0700321 v
0700298V
©BMW AG, Munich
Completely remove the protective film (1) on the adhesive strip, and remove the protective film (2) on the adhesive strip approx. 20 mm from mud flap AA.
II2l Bonding surfaces (1) must be cleaned with a cleaner and must be free from grease.�
Re-position mud flap AA and secure with expanding rivets AB and screw AC.
Introduce sheet metal nut AD behind the wheel arch (1 ) .
Secure mud flap AA using self-tapping screws AC.
05/2009 (VIZ) 34
-
0700302 v
0700303V
0700304 v
©BMW AG, Munich 01 290418179
Secure mud flap AA using screws AC from underneath.
Remove the protective film (1) from the adhesive strip on mud flap AA.
Press mud flap AA along its outer contour on the side wall.
05/2009 CVIZ) 35
-
1 6.Fitting rear mud flap X5M
0700291 v
0700382 v
0700373V
0700374 v ©BMW AG, Munich 01 290418179
Remove the existing blind rivets (1) as they are no longer needed.
Remove the existing screw (1) as it is no longer needed.
[2 Only place the expanding rivets BC in position, do not lock them.�
Position mud flap BB and hold in place with expanding rivets BC.
Mark out the drill holes (1) on mud flap BB in the wheel arch.
Then remove mud flap BB again.
05/2009 (ViZ) 36
-
0700376V
0700383V
070037 7 v ©BMW AG, Munich 01 29 0418179
[j Do not exceed the drilling depth since otherwise you may damage the car.�
Create a hole (1) of diameter 5 mm maintaining a maximum drlll depth of 5 mm.
Create a hole (2) of diameter 6 mm maintaining a maximum drill depth of 5 mm.
Below the four outer holes (1 ), create cuts (approx. 1 0 mm) for the sheet metal nuts BE using a knife.
Insert four sheet metal nuts BE into the drill holes.
Completely remove the protective film (1) on the adhesive strip, and remove the protective film (2) on the adhesive strip approx. 20 mm from mud flap BB.
[j Bonding surfaces (1) must be cleaned with a cleaner and must be free from grease.�
Position the mud flap BB and secure with expanding rivets BC.
05/2009 (VIZ) 37
-
©BMW AG, Munich
I I I I
'-® 0700379V
0700380V
[l] . .
0700381 v 01 2904181 79
Introduce sheet metal nut BE behind the wheel arch (1 ).
Secure mud flap BB using self-tapping screws BD.
Secure mud flap BB using screw BD and self-tapping screw B F from underneath.
Remove the protective film (1) from the adhesive strip on mud flap BB.
Press mud flap BB along its outer contour on the side wall.
05/2009 (V/Z) 38
-
17 .Concluding work and coding
This retrofit system does not require coding.
- Re-assemble the car
©BMW AG, Munich 01 290418179 0512009 (VIZ) 39
Installation Instructions; Mud flaps retrofit BMW X5/ X5M (E70)Table of contents1. Front mud flaps all 20"/21" parts list, M Sport package and X5M2. Front mud flaps 18"/ 19" parts list3. Rear mud flaps 18"/19" parts list4. Rear mud flaps 20"/21" without Aero package parts list5. Rear mud flaps 20"/21" with Aero package parts list6. Rear mud flaps kit 21" with M Sport package parts list7. Rear mud flaps kit X5M parts list8. Preparatory work9. Fitting the front mud flaps 18"/19" without step10. Fitting the front mud flaps 18"/19" with step11. Fitting front mud flaps 20"/21 ", M Sport package and X5M12. Fitting rear mud flaps 18"/ 19"13. Fitting rear mud flaps 20"/21" without Aero package14. Fitting rear mud flaps 20"/21" with Aero package15. Fitting rear mud flaps 20"/21" with M Sport package16. Fitting rear mud flap X5M17. Concluding work and coding