codecard cicemu for bmw x5 e70, x6 e71 with rear view

17
All right reserved www.codecard.lt 1 CODECARD CICEMU for BMW X5 E70, X6 E71 with rear view camera CIC retrofit connection manual You will need soldering iron and some electric skills. After instalation CIC needs to be coded and adapted to car! If your BMW has Video modul (rear view camera is connected to VM, not directly to CIC), you must reconnect camera to CIC directly. Check car wiring diagrams. For first prepare BMW CIC emulator board: solder 6 wires ~ 15cm long to emulator C1H, C1L, C2H, C2L, GND and +12 points. This will help you in installation process. If car don’t have rear view camera – short 1 jump like in picture: CIC need to be coded to car with INPA or other diagnostic tool – enable parktronic and rear view camera if needed.

Upload: others

Post on 07-Feb-2022

11 views

Category:

Documents


1 download

TRANSCRIPT

All right reserved www.codecard.lt 1

CODECARD CICEMU for BMW X5 E70, X6 E71 with rear

view camera CIC retrofit connection manual

You will need soldering iron and some electric skills. After instalation CIC needs to be coded and adapted to car! If your BMW has Video modul (rear view camera is connected to VM, not

directly to CIC), you must reconnect camera to CIC directly. Check car wiring diagrams.

• For first prepare BMW CIC emulator board: solder 6 wires ~ 15cm long to emulator C1H, C1L, C2H, C2L, GND and +12 points. This will help you in installation process. If car don’t have rear view camera – short 1 jump like in picture:

CIC need to be coded to car with INPA or other diagnostic tool – enable parktronic and rear view camera if needed.

All right reserved www.codecard.lt 2

• Solder configuration jumps according pictures:

- For BMW car with parktronic and original CCC rear view camera solder jump 1 and 3:

- For BMW car with parktronic and OEM (retrofitted, not original) rear view camera solder jump 3:

All right reserved www.codecard.lt 3

How to remove CIC on E90 you can found on:

http://www.e90post.com/forums/showthread.php?t=264254 --- thank you for this info

Steps 1-3

1. IMPORTANT: Turn ignition off, and pull key from ignition lock before installing the

emulator! Better is also remove battery negative plug. Remove the trim by pulling out on the end (1) and the middle (2). Unclip the plugs from the START/STOP button and the

button panel between the air vents.

2. Pull out the Climate Control panel and disconnect the plugs on it's back.

All right reserved www.codecard.lt 4

3. Remove cover plate from Multimedia unit keypad. Like all the other parts it is just snapped in place.

All right reserved www.codecard.lt 5

Steps 4-6 4. Remove the 4 screws shown in the picture. Then pull Multimedia unit out. Be careful

not to scratch the gear shifter (use towel).

All right reserved www.codecard.lt 6

5. Unplug the large black plastic plug by squeezing the tabs (1) together while pulling outward (direction of the arrow).

All right reserved www.codecard.lt 7

All right reserved www.codecard.lt 8

Disconnect CIC unit. Find spitted CAN wires – pins 9 and 11. Cut these wires. Connect

emulator like in picture

All right reserved www.codecard.lt 9

After connection insulate BMW CIC emulator board with heat shrink or insulation tape.

All right reserved www.codecard.lt 10

CIC emulator installation inside CIC

Just look installation pictures.

All right reserved www.codecard.lt 11

All right reserved www.codecard.lt 12

All right reserved www.codecard.lt 13

All right reserved www.codecard.lt 14

All right reserved www.codecard.lt 15

All right reserved www.codecard.lt 16

All right reserved www.codecard.lt 17