ontent - glsciences.eu · 2406-1006 optic injector metal ferrule column id 0.32mm pk/ 10 h100021...
TRANSCRIPT
2
Content Page
OPTIC Liners 3
OPTIC 2
Consumables 5
OPTIC 3
Consumables 7
Spare Parts 9
OPTIC-4
Consumables 12
Spare Parts 13
OPTIC accessories 15
LINEX
Consumables, spare parts 16
PHASER
Consumables 17
Spare Parts 18
3
OPTIC Liners
Part number Description Explanation
A100001 Fritted Liner This liner contains a medium porosity frit made . This liner can be used for hot
and cold Split/Less injections. In addition, if used with a suitable packing mate-
rial the liner can be used for large volume injection, thermal desorption, solid
sampling and pyrolysis applications. Pk/ 5
A100049 Splitless Liner This liner is for hot and cold splitless injection of sample volumes below 1 µl. The narrow internal diameter of 1 mm ensures fast transfer of the sample to the column under splitless conditions. We advise this liner for SPME tech-niques. Pk/ 5
A100092 Single-Necked Liner This liner is specially made for hot or cold split injections. The large internal
diameter of 3.4 mm facilitates mixing of the sample with the carrier gas.
Pk/ 5
A100095 “8270” Packed Lin-
er
This liner contains a highly deactivated packing that combines a maximum operating temperature of 350 °C with a high sample capacity (in excess of 100µl in most cases). This liner has been developed for the EPA 8270 method.
A100132 Baffled Splitless
Liner
This liner is for hot and cold splitless injection of sample volumes below 1 µl.
The narrow internal diameter of 1 mm ensures fast transfer of the sample to
the column under splitless conditions. With this liner the sample will not have
any chance of being injected directly to the bottom of the injector. This liner
will give better results for the high boiling components.
Pk/ 5
A100133 Sintered glass liner This liner is both very inert and capable of operation up to 350°C. As such it is
suitable for the large volume injection of compounds that have the tendency
to breakdown. The capacity of the liner is lower than that of a packed liner
(about 50 µl, depending upon solvent used). To maximize its capacity, the
liner should be used in combination with a syringe fitted with a dome tipped,
side-hole needle. Pk/ 5
A100133S Special deactivated
Sintered glass liner
This liner is both very inert, highly deactivated and capable of operation up to
350°C. As such it is suitable for the large volume injection of compounds that
have the tendency to breakdown. The capacity of the liner is lower than that
of a packed liner (about 50 µl, depending upon solvent used). To maximize its
capacity, the liner should be used in combination with a syringe fitted with a
dome tipped, side-hole needle. Pk/ 5
A100136 Fritted liner
(frit 20 mm) filled
with Tenax TA
The liner contains Tenax TA 60-80 mesh packing material that combines a
maximum operating temperature (350°C) with a high sample capacity (in
excess of 100 µl in most cases). Pk/ 5
A100137 Fritted Liner filled
with Tenax GR
The liner contains Tenax GR 80-100 mesh packing material that combines a
maximum operating temperature (350°C) with a high sample capacity (in
excess of 100 µl in most cases). Pk/ 5
A100140 Fritted Liner (frit on
15 mm) packed
with Tenax TA
The liner contains Tenax TA 60-80 mesh packing material that combines a
maximum operating temperature (350°C) with a high sample capacity (in
excess of 100 µl in most cases). Pk/ 5
A100145 Starter Kit for LVI
Sampling, pack of 5
different liners
A starter kit for large volume injections. With 5 different liners.
1 x A100001, fritted liner
1 x A100049, single necked liner
1 x A100060, A-type packed liner
1 x A100132, Baffled splitless liner
1 x A100133, Sintered glass liner
4
OPTIC Liners
Part number Description Explanation
A100146 Fritted Liner
packed with
Chromosorb W
The liner contains Chromosorb W packing material that combines a maximum
operating temperature (350°C) with a high sample capacity (in excess of 100
µl in most cases). Pk/ 5
L100009 Fritted liner with
taper
This liner contains a medium porosity frit made from sintered, deactivated
glass. With a taper on the bottom. This liner can be used for split/less, ther-
mal desorption, pyrolysis injections. In addition, if used with a suitable pack-
ing material the liner can be used for large volume injection, thermal desorp-
tion, solid sampling and pyrolysis applications.
Pk/ 5
L100011 LINEX DMI tapered
liner
This liner has special dents to hold the DMI-vail. This ensures that there will be
no compounds traps on the frit. The taper will increase sensitivity of the
increased linear velocity to the column, which will reduce peak width and
increase peak height
Pk/ 5
L100012 Needle Guide DMI
Tapered liner
The needle guide will ensure the automated introduction of sample in the
DMI Vial when using a extra long needled syringe.
Pk/ 5
L100013 LINEX metal Needle
Guide
The needle guide will ensure the automated introduction of sample in the
DMI Vial when using a extra long needled syringe. Made out of metal
Pk/ 1
2406-1010 DMI Sample Insert
30µl
The container for sample when using the DMI technique, volume 30 µl.
Pk/ 100
2406-1020 DMI Sample Insert,
60 µl
The container for sample when using the DMI technique, volume 60 µl.
Pk/ 100
5
OPTIC 2 Consumables
Part number Description
A100014
PTFE Covered Septum, 9 mm
Pk/50
A100015
Graphite Ferrule for 0.25 - 0.32
mm ID Column, Pk/10
A100016
Graphite Ferrule for 0.53 mm ID
Column, Pk/10
A100030
PTFE Reducing Ferrule, 1/8" to
1/16", Pk/10
A100041
High Quality Low Bleed Septum
9 mm, Pl/25
A100067
PTFE Top Boss Insulator,
Pk/10
A100111
Merlin Micro-seal ®
Pk/ 1
6
OPTIC 2 Consumables
Part number Description
A100120
Brass Liner Blanking Cap
Pk/10
A100122
Nylon Liner Blanking Cap
Pk/10
A1000141
Stainless Steel Liner Blanking Cap
Pk/10
A100124
Graphite Ferrule for 0.1-0.18 mm
ID Column, pk/10
7
OPTIC 3 Consumables
Part number Description
A100030
PTFE Reducing Ferrule, 1/8" to
1/16", pk/10
A100067
PTFE Top Boss Insulator,
pk/10
3007-11605
High resistance Silicon O-ring for
liner
pk/ 20
H100001
General Purpose Red Septa 11
mm, pk/25
H100002
Has been replaced by
2406-1002
Low Bleed White Septum 11 mm
pk/25
H100003
Has been replaced by
2406-1003
Graphite Ferrule for 0.53 mm ID
Column, pk/10
H100004
Has been replaced by
2406-1004
Graphite Ferrule for 0.1 - 0.32 mm
ID Column, pk/10
8
OPTIC 3 Consumables
Part number Description
H100007
Graphite/Vespel Ferrule
(for OPTIC 3 Special Tee)
pk/10
H100009
O-ring for 1/4 Tube, 5.7 x 1.9
pk/ 25
H100010
Empty tube for Thermal
Desorption 1/4
pk/5
H100012
100 µl syringe for Shimadzu AOC
20i
pk/ 3
H100013
OPTIC 3 HT Injection Port Septa
transparent
pk/ 25
H100019
Has been replaced by
2406-1005
OPTIC Injector Metal Ferrule
Column ID =<0.25mm
pk/10
H100020
Has been replaced by
2406-1006
OPTIC Injector Metal Ferrule
Column ID 0.32mm
pk/ 10
H100021
has been replaced by
2406-1007
OPTIC Injector Metal Ferrule
Column ID 0.53mm
pk/ 10
H200139
has been replaced by
2406-2049
OPTIC injector metal nut for met-
al ferrule, pk/ 5
9
OPTIC 3 Spare parts
Part number Description
H200001
has been replaced by
2406-2047
Stainless Steel Injector Bottom
Nut
pk/ 5
H200002
Has been replaced by
2406-2010
Standard Septum Nut
pk/ 1
H200003
Has been replaced by
2406-2012
Clamp Nut Insulator
pk/ 1
H200004 Has been
replaced by 2406-
1002
Injector Bottom Insulation Cap
pk/ 1
H200005
Has been replaced by
2406-2270
GC Oven Thermocouple
pk/ 1
H200007
OPTIC 3 EGC Fitting 1/8"
pk/ 1
10
OPTIC 3 Spare parts
Part number Description
H200008
Viton O-ring for EGC Fittings
Pk/ 100
H200037
One-touch mini connector for
OPTIC 3 cooling valve Pk/
1
H200044
OPTIC 3 Charcoal Split Filter
Cartridge
Pk/ 1
H200050
Split Line Charcoal Filter
Assembly (H200044 + H200051)
Pk/ 1
H200139
Has been replaced by
2406-2039
OPTIC Injector Metal Nut for met-
al ferrule Pk/
5
L200218
Fitting 1/16 OD tubing
10-32 thread
Pk/ 1
11
OPTIC 3 Spare parts
Part number Description
H400038
Solvent Monitor Assembly
Pk/ 1
H400058
Septum Nut Sampling connection
(1/16)
Pk/ 1
H500021
has been replaced by
2406-2048
Key for OPTIC Injector Bottom
Nut Pk/
1
H500024
has been replaced by
2406-2039
OPTIC 3 Column Mounting Jig
Pk/ 1
L100007
has been replaced by
2406-1008
Liner O-ring
material: Viton
Pk/ 50
12
OPTIC-4 Consumables
Part number Description
2406-1002
OPTIC Low Bleed White Septum,
11 mm, pk/25
2406-1003
OPTIC Graphite Ferrule for 0.53
mm ID Column, pk/10
2406-1004
OPTIC Graphite Ferrule for 0.1 -
0.32 mm ID Column, pk/10
2406-1005
OPTIC Inlet Metal Ferrule, Col-
umn ID 0.25mm, pk/10
2406-1006
OPTIC Inlet Metal Ferrule, Col-
umn ID 0.32mm, pk/10
2406-1007
OPTIC Inlet Metal Ferrule, Col-
umn ID 0.53mm, pk/10
2406-1008
OPTIC Viton O-ring 4.5 ID x 2.0,
pk/50
2406-1009
OPTIC EFC Inlet Connection o-
ring, pk/50
2406-1010
OPTIC DMI Sample Insert 30µl,
pk/100
3007-11605
OPTIC High Resistance Silicon o-
ring P5, pk/20
13
OPTIC-4 Spare parts
Part number Description
2406-2039
OPTIC Column Mounting Jig
2406-2047
OPTIC Stainless Steel Inlet Bot-
tom Nut, pk/5
2406-2048
Key for OPTIC Inlet Bottom Nut
2406-2049
OPTIC Inlet Bottom Nut for Metal
Ferrule, pk/5
2406-2010
OPTIC-4 Inlet Septum Nut Stand-
ard
2406-2013
OPTIC-4 Inlet Clamp Nut Insulator
2406-2015
OPTIC-4 Inlet Septum Nut,
Shimadzu type
2406-2016
OPTIC-4 Inlet Septum Nut Insert,
Shimadzu type
2406-4021
OPTIC-4 External Solvent Monitor
Assembly
14
OPTIC-4 Spare parts
Part number Description
2406-4205
OPTIC-4 Inlet Cooling Valve
2406-2051
OPTIC-4 EFC Fitting, 1/8" tubing
3007-16201
Shimadzu aluminum packing type
-G, pk/100
2406-2257
Fuse, Slow Blow, 230V, 6.3A, pk/5
2406-2269
OPTIC Inlet Bottom Insulation
Cap
2406-2270
OPTIC GC Oven Thermocouple
2406-4025
OPTIC-4 Split Line Filter Assy
15
OPTIC Accessories
Part number Description
G300025
Gas Leak Detector LD239
Pk/ 1
3001-12101
Packing Funnel for Liners
Pk/ 1
3001-12701
Glass wool inserter
Pk/ 1
3001-12801
Glass wool remover
Pk/ 1
3001-12720
Septum Pick
Pk/ 1
3001-12730
Injector port cleaning Kit
Pk/ 4
3001-12745
Ferrule removal tool
Pk/ 1
2406-4164
Or
2406-4167
OPTIC Standard On-Column Tool
kit
Or
OPTIC On-Column Tool kit for
Shimadzu GC
16
LINEX Consumables
Part number Description
3007-11605 High resistance Silicon O-ring for
liner, pk/ 20
L400020
Has been replaced by
2411-4107
CDCS Liner Caps Assy
Pk/ 50
2411-2046 Fitting 1/16" OD tubing, 10-32
thread, pk/1
2411-2001 LINEX Bushing
LINEX Accessories
Part number Description
L200043
Has been replaced by
2411-2500
CDCS 98 position Tray for Capped
Liners
Pk/ 1
L200030
Has been replaced by
2411-2026
LINEX 98 position Tray, Plastic
Pk/ 1
L500001
Has been replaced by
2411-4100
LINEX Capping-De-Capping
Station 2.0
Pk/ 1
17
PHASER Consumables
Part number Description
3007-14105
Graphite Ferrule for 0.25 mm
column
pk/ 10
3007-14108
Graphite Ferrule for 0.32 mm
column
pk/ 10
3007-14110
Graphite Ferrule for 0.53 mm
column
pk/ 10
3007-31104
Graphite Vespel ®Ferrule for
<0.25 mm column
Pk/ 10
3007-31105
Graphite Vespel ®Ferrule for
0.25 mm column
Pk/ 10
3007-31108
Graphite Vespel ®Ferrule for
0.32 mm column
Pk/ 10
3007-31110
Graphite Vespel ®Ferrule for
0.53 mm column
Pk/ 10
18
PHASER Spare parts
Part number Description
2702-18506
Glass Nose Cone
Type Y
Pk/ 1
2702-18505
Glass Nose Cone
Type R
Pk/ 1
sge123730
SilFlow 4 Port Splitter 1.1mm Port
sge123704 SilFlow Nuts , pk/10
sge123705 SilFlow Ferrules 1.1mm ID, Pk/5
sge123706 SilFlow Ferrules 0.4mm ID, pk/10
sge123707 SilFlow Ferrules 0.5mm ID , pk/10
sge123709 SilFlow Ferrules 0.7mm ID, pk/10
sge123713 SilFlow Ferrules 0.35mm ID, pk/10
sge123717 SilTite FingerTite Tool
sge123742 SilFlow Ferrules 0.8mm ID
sge123755 SilFlow SS capillary Tubing 1.1 mm
OD Sleeved to 1/16"
19
PHASER Spare parts
Part number Description
2702-18560 Spare Fuse 250 V T 3 A
5.2 x 20 mm
2702-18561 Spare Fuse 250 V T 5 A
5.2 x 20 mm, pk/2
3004-32231 PFA Tubing
3.18 mm O.D. x 1.58 mm I.D.
Pk/10 m
3004-50041 Sulfinert® Tubing
0.74 mm O.D. x 0.53 mm I.D.
Pk/ 7,5 m
1010-36132 Fused Silica Capillary Tubing
0.150 mm I.D. x 0.375 mm O.D.
Pk/ 10 m
1010-36222 Fused Silica Capillary Tubing
0.200 mm I.D. x 0.350 mm O.D.
Pk/ 10 m
1010-36322 Fused Silica Capillary Tubing
0.250 mm I.D. x 0.350 mm O.D.
Pk/ 10 m
1010-36452 Fused Silica Capillary Tubing
0.250 mm I.D. x 0.350 mm O.D.
Pk/ 10 m
1010-36682 Fused Silica Capillary Tubing
0.200 mm I.D. x 0.350 mm O.D.
Pk/ 10 m