nuc box 8265u nuc box 8365ue user manual - asrockdownload.asrock.com/ipc/manual/nuc box...

NUC BOX 8265UNUC BOX 8365UE

User Manual

Version 1.0Published October 2019

Version 1.0 Published December 2019 Copyright©2019 ASRock Inc. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock’s Website: www.ASRock.com

Replaceable batteries

CAUTIONRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Contact Information

If you need to contact ASRock or want to know more about ASRock, you’re welcome to visit ASRock’s website at www.ASRock.com; or you may contact your dealer for further information.

ASRock Incorporation6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,

Taipei City 112, Taiwan (R.O.C.)

The terms HDMI® and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Product Specifications 2

1.3 Block Diagram 4

Chapter 2 Product Overview 6

2.1 Front View 6

2.2 Rear View 7

2.3 Inside View 8

Chapter 3 Hardware Installation 9

3.1 How to Remove the Bottom Case 9

3.2 How to Install the WiFi Module 10

3.3 How to Install the M.2 SSD 11

3.4 How to Install the 2.5-inch Hard Drive 12

3.5 How to Install the Memory Modules (DDR4 (1.2V)) 14

3.6 How to Install the M.2 Heatsink 15

Chapter 4 Motherboard (NUC BOX 8365UE) 16

4.1 Motherboard Layout 16

4.2 Motherboard Specifications 17

4.3 Jumpers Setup 19

4.4 Onboard Headers and Connectors 20

4.5 Expansion Slots (M.2 Slots) 23

Chapter 5 Motherboard (NUC BOX 8265U) 24

5.1 Motherboard Layout 24

5.2 Motherboard Specifications 25

5.3 Jumpers Setup 27

5.4 Onboard Headers and Connectors 28

5.5 Expansion Slots (M.2 Slots) 31

Chapter 6 UEFI Setup Utility (NUC BOX 8365UE) 32

6.1 Introduction 32

6.2 Main Screen 33

6.3 Advanced Screen 34

6.4 Hardware Health Event Monitoring Screen 45

6.5 Security Screen 46

6.6 Boot Screen 47

6.7 Exit Screen 49

Chapter 7 UEFI Setup Utility (NUC BOX 8265U) 50

7.1 Introduction 50

7.2 Main Screen 51

7.3 Advanced Screen 52

7.4 Hardware Health Event Monitoring Screen 61

7.5 Security Screen 62

7.6 Boot Screen 63

7.7 Exit Screen 65

Chapter 8 Software Support 66

8.1 Install Operating System 66

8.2 Support CD Information 66

NUC BOX 8265U/8365UE

PB 1

Engl

ish

Chapter 1 Introduction

1.1 Package Contents• NUC BOX 8265U/8365UE• NUC-8265U/NUC-8365UE (pre-installed motherboard)• 1 x SATA 1 to 1 Power Cable• 4 x HDD Screws (M3x4)• 1 x WiFi Module Screw • 1 x Screw for M.2 slot• 1 x 96W Power Adapter• User Manual

Because the hardware specifications might be updated, the content of this documentation will be subject to change without notice.

If any items are missing or appear damaged, contact your authorized dealer.

2 3

English

1.2 Product Specifications


Barebone

CPUIntel® 8th Gen (Whiskey lake-U) Core™ MCP Processors

NUC BOX 8265U (I5-8265U QC, 1.6HGz, 15W)NUC BOX 8365UE (I5-8365UE QC, 1.6GHz, 15 W)

OS N/A

Chipset SoC

Memory Supports Dual Channel DDR4 2400 MHz, 2 x SO-DIMM slots, Max. 32GB

HDD

Optional

Supports 1 x 2.5" SATA HDD*/SSD

LAN Gigabit LAN

WiFi Optional

Audio Realtek ALC233

Front I/O 1 x USB 3.1 (Type A), 2 x USB 2.0 (Type A), 1 x Audio-out with MIC-In

Rear I/O 2 x USB 3.1 (Type A), 1 x HDMI, 2 x DP, 2 x LAN, DC-IN, 1 x Kensington lock

Power Unit 96W Adapter

Dimension 110.mm (W)x 118.5mm (D) x 67.3mm (H)

M.2 slot

2.5”HDD


2 3

Engl

ish

* For NUC BOX 8265U/8365UE, it is not recommended to install 2.5” HDD. If you install the 2.5” HDD, please keep the NUC BOX 8265U/8365UE in a vertical position to ensure better cooling performance.

VESA Bracket included , supports 75 x 75 and 100 x 100 mm

Volume (Liters)

0.6L

Operating Temperature

0°C~40°C

4 5

English

1.3 Block Diagram

NUC BOX 8265U

55

44

33

22

11

DD

CC

BB

AA

Gb LAN

RJ45

DIS

PL

AY

1DDI1

Gb LAN

RJ45

LA

N2 +

US

B3.0

HDMI 1.4b

DP 2

DP 1

RTL8111G

PAGE:28

480Mbp/s

PCIe 8

5Gb/s

SPI

LPC1

3.3V LPC

FA

NX

11x CPU FAN(4-pin)

12V only

Serial Port * 1

- Internal Header *1(RS-232/422/485)

5Gb/s

SP

I FL

AS

H3

.3V

/12

8M

b

NUC-8265U

Au

dio

EDP

Com

bo D

P+

HD

MI

Headset

(combo jack)

eD

P T

O H

DM

I

CHRONTEL CH7525A-BF

M.2

M-K

EY

slot

(2242/2

260/2

280 b

y b

rack

et)

HDA/I2S

DDI2

DD

R4 S

O-D

IMM

2400

DDR4 - CH1

M.2

E-K

EY

(2230)

PCIe 9

USB2.0

LA

N1+

US

B 3

.0

1 F

ro

nt U

SB

3.0

po

rt T

yp

e A

1 P

OR

T

SATA Port 0

Gen3 x1 port

SATA Port 1

Gen3 x1 port

NUC Form Factor

Inte

rn

al U

SB

2.0

Hea

der

2 P

OR

T

C.S ALC233-VB2 MQFN-48

REALTEK/COPPER MATERIAL

I219V

NCT5567D(C)

SPI TPM SLB9670VQ2.0

TP

M

PCIe*1+USB

WH

L-U

LT

RA

Inte

l

SP

I

SA

TA

3_

1

PAGE:36

PAGE:27

PAGE:20,21

SIO

128-bit Dual-Channel Memory x 2 Slots

DD

R4 S

O-D

IMM

2400

DDR4 - CH0

PCIe 7

5Gb/s

PAGE:20,21

PAGE:29

PAGE:22

PAGE:25

PAGE:25

PAGE:29

PAGE:35

PAGE:15

PAGE:23

PAGE:24

PAGE:31

PAGE:33

PAGE:33

PAGE:26

PCIe 13,14,15,16

PCIe*4/SATA


4 5

Engl

ish

NUC BOX 8365UE

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

Gb LAN

RJ45

DIS

PL

AY

1DDI1

Gb LAN

RJ45

LA

N2 +

US

B3.0

HDMI 1.4b

DP 2

DP 1

RTL8111G

PAGE:28

480Mbp/s

PCIe 8

5Gb/s

SPI

LPC1

3.3V LPC

FA

NX

11x CPU FAN(4-pin)

12V only

Serial Port * 1

- Internal Header *1(RS-232/422/485)

5Gb/s

SP

I F

LA

SH

3.3

V/1

28M

b

NUC-

8365

UE

Au

dio

EDP

Com

bo D

P+

HD

MI

Headset

(combo jack)

eD

P T

O H

DM

I

CHRONTEL CH7525A-BF

M.2

M-K

EY

slo

t(2

242/2

260/2

280 b

y b

rack

et)

HDA/I2S

DDI2

DD

R4 S

O-D

IMM

2400

DDR4 - CH1

M.2

E-K

EY

(2230)

PCIe 9

USB2.0

LA

N1+

US

B 3

.0

1 F

ron

t U

SB

3.0

port

Typ

e A

1 P

OR

T

SATA Port 0

Gen3 x1 port

SATA Port 1

Gen3 x1 port

NUC Form Factor

Inte

rn

al

US

B2.0

Head

er

2 P

OR

T

C.S ALC233-VB2 MQFN-48

REALTEK/COPPER MATERIAL

I219LM

NCT5567D(C)

SPI TPM SLB9670VQ2.0

TP

M

PCIe*1+USB

WH

L-U

LT

RA

Inte

l

SP

I

SA

TA

3_

1

PAGE:36

PAGE:27

PAGE:20,21

SIO

128-bit Dual-Channel Memory x 2 Slots

DD

R4 S

O-D

IMM

2400

DDR4 - CH0

PCIe 7

5Gb/s

PAGE:20,21

PAGE:29

PAGE:22

PAGE:25

PAGE:25

PAGE:29

PAGE:35

PAGE:15

PAGE:23

PAGE:24

PAGE:31

PAGE:33

PAGE:33

PAGE:26

PCIe 13,14,15,16

PCIe*4/SATA

6 7

English

Chapter 2 Product OverviewThis chapter provides diagrams showing the location of important components of the NUC BOX 8265U/8365UE.

2.1 Front View

No. Description

1 USB 3.0 (Type A)2 Audio(Mic-in, Line-out)3 2 x USB 3.1 (Type A)4 Power Button

1 2

3

4


6 7

Engl

ish

2.2 Rear View

No. Description

1 DC-IN2 HDMI3 2 x USB 3.1 (Type A)4 2 x DisplayPort5 2 x RJ-45

* There are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.

Activity / Link LED Speed LED

Status Description Status DescriptionOff No Link Off 10Mbps connectionBlinking Data Activity Orange 100Mbps connectionOn Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

1 2 3

4 5

8 9

English

2.3 Inside View

No. Description

1 Mini PCIe Slot2 M.2 Slot 3 SATA 3.0 Connector4 SO-DIMM Slot5 Hard disk drive tray (compatible with 2.5" SATA HDD/SSD)

SO-DIMM memory, hard drive and mSATA SSD are not included with this system.

4

2

1

3

5


8 9

Engl

ish

Chapter 3 Hardware InstallationThis chapter helps you install or remove important components.

3.1 How to Remove the Bottom Case1. Remove the four screws on the bottom case.2. Then lift up and remove the bottom panel..

10 11

English

3.2 How to Install the WiFi Module1. Locate the WiFi Module slot on the motherboard.

2. Carefully insert the WiFi Module into the slot.

3. Tighten the screw to secure the WiFi Module to the motherboard.


10 11

Engl

ish

3.3 How to Install the M.2 SSD1. Locate the M.2 slot on the motherboard.

2. Carefully insert the M.2 SSD into the slot.

3. Tighten the screw to secure the M.2 SSD to the motherboard.

12 13

English

3.4 How to Install the 2.5-inch Hard Drive1. Remove the four screws on the bottom case. Then lift up and remove the bottom panel.

2. Attach the HDD to the hard drive mounting bracket and secure it using the four screws.


12 13

Engl

ish

3. Attach the HDD assembly to the bottom panel and secure it using the four screws. Connect the SATA Data and Power Cable to the HDD.

4. Then reinstall the bottom panel.

14 15

English

3.5 How to Install the Memory Modules (DDR4 (1.2V))

1. Carefully insert the SO-DIMM memory modules into the slot at a 30-degree angle.

2. Push down until the modules snap into place.

1. The NUC BOX 8265U/8365UE requires DDR4 SO-DIMM (1.2V).2. For dual channel configuration, you always need to install identical (the same brand,

speed, size and chip-type) DDR4 SO-DIMM pairs.

The SO-DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.


14 15

Engl

ish

3.6 How to Install the M.2 Heatsink1. Gently insert the M.2 module, along the guiding tabs, into the heatsink bracket.

2. Remove the membranes from both sides of the thermal pad. Then paste the thermal pad onto the M.2 module.

3. Align the heatsink to the edge of the bracket and press down the heatsink into the bracket until it clips into place.

16 17

English

Chapter 4 Motherboard (NUC BOX 8365UE)4.1 Motherboard Layout

M2

_2

AUDIO1

HD

MI1

USB 3.1:USB3_3

DC_IN1

M.2

SS

D(M

2_

1)

DP

2

DIS

PL

AY

1SATA3_1

DDR4_B1 (Support DDR4L Only)

DDR4_A1 (Support DDR4L Only)

SATA_PWR1

1

NUC-8365U

Industrial

LA

N1

US

B3

.1:

US

B3

_1

LA

N2

US

B3

.1:

US

B3

_2

BIOSROM

M2_SEL2

1

CLRMOS1

1

1

LP

C1

RESET HDLED

PWRBTN PLED

PANEL1

1

PW

R_

JP

1

1

USB2_3_4

1

COM1

1

1 : M.2 Key-M Socket (M2_1)2 : M.2 Key-E Socket (M2_2)3 : USB2.0 Connector (USB2_3_4)4 : COM Port Header (RS232/422/485)5 : System Panel Header (PANEL1)6 : LPC Debug Header (LPC1)7 : ATX/AT Mode Jumper (PWR_JP1)8 : SATA Power Output Connector (SATA_PWR1)9 : SATA3 Connector (SATA3_1) 10 : M.2 Select (M2_SEL1)11 : Clear CMOS Headers (CLRMOS1)

Back Side :Power Button (PWR_BTN1)Fan Connector (FAN1)


16 17

Engl

ish

4.2 Motherboard Specifications

Form Factor Dimensions NUC 4.09" x 4.02" (104 x 102mm)

Processor System

CPUIntel® 8th Gen (Whiskey lake-U) Core™ MCP ProcessorsI5-8365UE QC, 1.6GHz, 15 W (NUC-8365UE)

Chipset SoC

Expansion Slot

PCIe N/AMini-PCIe N/AmSATA N/A

M.2

1 x Key M (2242/2260/2280 by BRACKET) with PCIe x4 and SATA3 for SSD1 x Key E (2230) with PCIe x1 and USB 2.0 for Wireless

MemoryTechnology Dual Channel DDR4 2400 MHzMax. 32GBSocket 2 x SO-DIMM

Graphics

Controller N/ADVI N/ALVDS N/A

HDMIHDMI 1 : Supports max resolution up to 4Kx2K@30Hz

DisplayPortSupports max resolution up to 3840 x 2160@60Hz

Multi Display Triple DisplayeDP N/A

Ethernet Ethernet 10/100/1000 MbpsController 1 x Intel® I219LM, 1 x Realtek RTL8111G)

Front I/O Audio 1 (Mic-in, Line-out)USB 1 x USB 3.1, 2 x USB 2.0

Rear I/O

HDMI 1DisplayPort 2Ethernet 2USB 2 x USB 3.1

18 19

English

Internal Connector

USB 2 x USB 2.0LVDS/inverter

N/A

eDP N/AVGA N/ASerial 1 x COM (RS-232/422/485)SATA 1 x SATA3 ( 6.0Gb/s)Parallel N/AGPIO N/ASATA PWR Output

1

Speaker Header

N/A

TPM N/AWatchdog Timer

Output N/AInterval N/A

Power Requirements

Input PWR 12V / 96W DC-In (DC Jack)

Power OnATX SupportedATX: Press Button to PWR on after Power input ready

Environment

Operating Temp

0ºC – 60ºC

Storage Temp

-40ºC – 85°C


18 19

Engl

ish

4.3 Jumpers SetupThe illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Clear CMOS Jumper (3-pin CLRMOS1)

(see p.24, No. 11)

Note: CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

ATX/AT Mode Jumper 1-2: AT Mode(3-pin PWR_JP1) 2-3: ATX Mode(see p.24, No. 7)

M.2 Select Open: M.2(2-pin M2_SEL1) Short: SATA3_1(see p.24, No. 10)

1

20 21

English

4.4 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

SATA Power Output Connector Please connect a SATA (SATA_PWR1) power cable to this connector.(see p.24, No. 8)

SATA3 Connector This Serial ATA3 (SATA3) (SATA3_1: see p.24, No. 9) connector supports SATA data cables for internal storage devices. The current SATA3 interface allows up to 6.0 Gb/s data transfer rate.

USB 2.0 Connector There is one USB 2.0 (9-pin USB2_3_4) connector on this (see p.24 No. 3) motherboard.

DUMMY

GND GND

+B

-B

+A

-A

USB_PWR USB_PWR

1

_ DUMMY

1

System Panel Header This header accommodates(9-pin PANEL1) several system front panel (see p.24 No. 5) functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may configure

the way to turn off your system using the power switch.

GN

DR

ES

ET

#

PW

RB

TN

#

PL

ED

-

PL

ED

+

GN

D

HD

LE

D-

HD

LE

D+

1

GN

D


20 21

Engl

ish

LPC Debug Header This connector supports a (13-pin LPC1) Trusted Platform Module (TPM) (see p.24, No. 6) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.

RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the sys-tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

PCIRST#

FRAME

PCICLK

* This motherboard supports RS232/422/485 on COM1 port. Please refer to below table for the pin definition. In addition, COM1 port (RS232/422/485) can be adjusted in BIOS setup utility > Advanced Screen > Super IO Configuration. You may refer to page 24 for details.

PIN RS232 RS422 RS4851 DCD, Data Carrier Detect TX- RTX-2 RXD, Receive Data TX+ RTX+3 TXD, Transmit Data RX+ N/A4 DTR, Data Terminal Ready RX- N/A5 GND GND GND6 DSR, Data Set Ready N/A N/A7 RTS, Request To Send N/A N/A8 CTS, Clear To Send N/A N/A9 N/A N/A N/A

COM1 Port Pin Definition

COM Port Header (RS232/422/485) (9-pin COM1: see p.24, No. 4)

22 23

English

Back Side:Power Button Header(PWR_BTN1)

Fan Connector(FAN1)

1

FAN_SPEED_CONTROL

FAN_SPEED

+12VGND


22 23

Engl

ish

4.5 Expansion Slots (M.2 Slots)There are 2 M.2 slots on this motherboard.

M.2 for SSD: Key M (M2_1) (2242/2260/2280 by BRACKET) supports PCIe x4 and SATA3 for SSD.

M.2 for Wi-Fi: Key E (M2_2) (2230) supports PCIe x1 and USB 2.0 for Wireless.

M.2 Key-M Socket (M2M_1) M.2 Key-E Socket (M2E_1)

24 25

English

Chapter 5 Motherboard (NUC BOX 8265U)5.1 Motherboard Layout

M2

_2

AUDIO1

HD

MI1

USB 3.1:USB3_3

DC_IN1

M.2

SS

D(M

2_

1)

DP

2

DIS

PL

AY

1SATA3_1

DDR4_B1 (Support DDR4L Only)

DDR4_A1 (Support DDR4L Only)

SATA_PWR1

1

11

10

1

8

2 3 6

7

9NUC-8265U

Industrial

LA

N1

US

B3

.1:

US

B3

_1

LA

N2

US

B3

.1:

US

B3

_2

BIOSROM

M2_SEL2

1

CLRMOS1

1

1

LP

C1

RESET HDLED

PWRBTN PLED

PANEL1

1

PW

R_

JP

1

1

USB2_3_4

1

COM1

4 5

1

1 : M.2 Key-M Socket (M2_1)2 : M.2 Key-E Socket (M2_2)3 : USB2.0 Connector (USB2_3_4)4 : COM Port Header (RS232/422/485)5 : System Panel Header (PANEL1)6 : LPC Debug Header (LPC1)7 : ATX/AT Mode Jumper (PWR_JP1)8 : SATA Power Output Connector (SATA_PWR1)9 : SATA3 Connector (SATA3_1) 10 : M.2 Select (M2_SEL1)11 : Clear CMOS Headers (CLRMOS1)

Back Side :Power Button (PWR_BTN1)Fan Connector (FAN1)


24 25

Engl

ish

5.2 Motherboard Specifications

Form Factor Dimensions NUC 4.09" x 4.02" (104 x 102mm)

Processor System

CPUIntel® 8th Gen (Whiskey lake-U) Core™ MCP ProcessorsI5-8265U QC, 1.6HGz, 15W (NUC-8265U)

Chipset SoC

Expansion Slot

PCIe N/AMini-PCIe N/AmSATA N/A

M.2

1 x Key M (2242/2260/2280 by BRACKET) with PCIe x4 and SATA3 for SSD1 x Key E (2230) with PCIe x1 and USB 2.0 for Wireless

MemoryTechnology Dual Channel DDR4 2400 MHzMax. 32GBSocket 2 x SO-DIMM

Graphics

Controller N/ADVI N/ALVDS N/A

HDMIHDMI 1 : Supports max resolution up to 4Kx2K@30Hz

DisplayPort Supports max resolution up to 3840 x 2160@60HzMulti Display Triple DisplayeDP N/A

Ethernet Ethernet 10/100/1000 MbpsController 1 x Intel® I219V, 1 x Realtek RTL8111G

Front I/O Audio 1 (Mic-in, Line-out)USB 1 x USB 3.1, 2 x USB 2.0

Rear I/O

HDMI 1DisplayPort 2Ethernet 2USB 2 x USB 3.1

26 27

English

Internal Connector

USB 2 x USB 2.0LVDS/inverter

N/A

eDP N/AVGA N/ASerial 1 x COM (RS-232/422/485)SATA 1 x SATA3 ( 6.0Gb/s)Parallel N/AGPIO N/ASATA PWR Output

1

Speaker Header

N/A

TPM N/AWatchdog Timer

Output N/AInterval N/A

Power Requirements

Input PWR 12V / 96W DC-In (DC Jack)

Power OnATX SupportedATX: Press Button to PWR on after Power input ready

Environment

Operating Temp

0ºC – 60ºC

Storage Temp

-40ºC – 85°C


26 27

Engl

ish

5.3 Jumpers SetupThe illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Clear CMOS Jumper (3-pin CLRMOS1)

(see p.16, No. 11)

Note: CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

ATX/AT Mode Jumper 1-2: AT Mode(3-pin PWR_JP1) 2-3: ATX Mode(see p.16, No. 7)

M.2 Select Open: M.2(2-pin M2_SEL1) Short: SATA3_1(see p.16, No. 10)

1

28 29

English

5.4 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

SATA Power Output Connector Please connect a SATA (SATA_PWR1) power cable to this connector.(see p.16, No. 8)

SATA3 Connector This Serial ATA3 (SATA3) (SATA3_1: see p.16, No. 9) connector supports SATA data cables for internal storage devices. The current SATA3 interface allows up to 6.0 Gb/s data transfer rate.

USB 2.0 Connector There is one USB 2.0 (9-pin USB2_3_4) connector on this (see p.16 No. 3) motherboard.

DUMMY

GND GND

+B

-B

+A

-A

USB_PWR USB_PWR

1

_ DUMMY

1

System Panel Header This header accommodates(9-pin PANEL1) several system front panel (see p.16 No. 5) functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may configure

the way to turn off your system using the power switch.

GN

DR

ES

ET

#

PW

RB

TN

#

PL

ED

-

PL

ED

+

GN

D

HD

LE

D-

HD

LE

D+

1

GN

D


28 29

Engl

ish

LPC Debug Header This connector supports a (13-pin LPC1) Trusted Platform Module (TPM) (see p.16, No. 6) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.

RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the sys-tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

PCIRST#

FRAME

PCICLK

* This motherboard supports RS232/422/485 on COM1 port. Please refer to below table for the pin definition. In addition, COM1 port (RS232/422/485) can be adjusted in BIOS setup utility > Advanced Screen > Super IO Configuration.

PIN RS232 RS422 RS4851 DCD, Data Carrier Detect TX- RTX-2 RXD, Receive Data TX+ RTX+3 TXD, Transmit Data RX+ N/A4 DTR, Data Terminal Ready RX- N/A5 GND GND GND6 DSR, Data Set Ready N/A N/A7 RTS, Request To Send N/A N/A8 CTS, Clear To Send N/A N/A9 N/A N/A N/A

COM1 Port Pin Definition

COM Port Header (RS232/422/485) (9-pin COM1: see p.16, No. 4)

30 31

English

Back Side:Power Button Header(PWR_BTN1)

Fan Connector(FAN1)

1

FAN_SPEED_CONTROL

FAN_SPEED

+12VGND


30 31

Engl

ish

5.5 Expansion Slots (M.2 Slots)There are 2 M.2 slots on this motherboard.

M.2 for SSD: Key M (M2_1) (2242/2260/2280 by BRACKET) supports PCIe x4 and SATA3 for SSD.

M.2 for Wi-Fi: Key E (M2_2) (2230) supports PCIe x1 and USB 2.0 for Wireless.

M.2 Key-M Socket (M2M_1) M.2 Key-E Socket (M2E_1)

32 33

English

Chapter 6 UEFI Setup Utility (NUC BOX 8365UE)6.1 IntroductionThis section explains how to use the UEFI SETUP UTILITY to confi gure your system. The UEFI chip on the motherboard stores the UEFI SETUP UTILITY. You may run the UEFI SETUP UTILITY when you start up the computer. Please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter the UEFI SETUP UTILITY, otherwise, POST will continue with its test routines.If you wish to enter the UEFI SETUP UTILITY after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may also restart by turning the system off and then back on.

Because the UEFI software is constantly being updated, the following UEFI setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen.

6.1.1 UEFI Menu Bar The top of the screen has a menu bar with the following selections: Main To set up the system time/date informationAdvanced To set up the advanced UEFI featuresH/W Monitor To display current hardware statusSecurity To set up the security featuresBoot To set up the default system device to locate and load the

Operating SystemExit To exit the current screen or the UEFI SETUP UTILITY Use < > key or < > key to choose among the selections on the menu bar, and then press <Enter> to get into the sub screen. You can also use the mouse to click your required item.

Use < > key or < > key to choose among the selections on the menu Use < > key or < > key to choose among the selections on the menu


32 33

Engl

ish

6.1.2 Navigation Keys Please check the following table for the function description of each navigation key. Navigation Key(s) Function Description / Moves cursor left or right to select Screens / Moves cursor up or down to select items + / - To change option for the selected items<Enter> To bring up the selected screen<F1> To display the General Help Screen<F7> Discard changes<F9> To load optimal default values for all the settings<F10> To save changes and exit the UEFI SETUP UTILITY<F12> Print screen<ESC> To jump to the Exit Screen or exit the current screen

6.2 Main ScreenWhen you enter the UEFI SETUP UTILITY, the Main screen will appear and display the system overview.

34 35

English

Setting wrong values in this section may cause the system to malfunction.

6.3 Advanced ScreenIn this section, you may set the configurations for the following items: CPU Configu-ration, Chipset Configuration, Storage Configuration, Super IO Configuration, AMT Configuration, ACPI Configuration, USB Configuration and Trusted Computing.

Instant FlashInstant Flash is a UEFI flash utility embedded in Flash ROM. This conve-nient UEFI update tool allows you to update system UEFI without entering operating systems first like MS-DOS or Windows®. Just launch this tool and save the new UEFI file to your USB flash drive, floppy disk or hard drive, then you can update your UEFI only in a few clicks without prepar-ing an additional floppy diskette or other complicated flash utility. Please be noted that the USB flash drive or hard drive must use FAT32/16/12 file system. If you execute Instant Flash utility, the utility will show the UEFI files and their respective information. Select the proper UEFI file to update your UEFI, and reboot your system after UEFI update process completes.


34 35

Engl

ish

6.3.1 CPU Configuration

Intel Hyper Threading Technology To enable this feature, a computer system with an Intel processor that sup-

ports Hyper-Threading technology and an operating system that includes optimization for this technology, such as Microsoft® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit is required. Set to [Enabled] if using Microsoft® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit or Linux kernel version 2.4.18 or higher. This option will be hidden if the installed CPU does not support Hyper-Threading technology.

Active Processor CoresSelect the number of cores to enable in each processor package.

CPU C States SupportEnable CPU C States Support for power saving. It is recommended to keep C3, C6 and C7 all enabled for better power saving.

Intel Virtualization Technology When this option is set to [Enabled], a VMM (Virtual Machine Architecture)

can utilize the additional hardware capabilities provided by Vanderpool Technology. This option will be hidden if the installed CPU does not

support Intel Virtualization Technology.Intel SpeedStep Technology Intel SpeedStep technology is Intel’s new power saving technology. Pro-

cessors can switch between multiple frequencies and voltage points to en-able power saving. The default value is [Enabled]. Configuration options:

[Enabled] and [Disabled]. If you install Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit and want to enable this function, please set this item to [Enabled]. This item will be hidden if the current CPU does not support In-tel SpeedStep technology.

36 37

English

Intel Turbo Boost Technology Use this item to enable or disable Intel Turbo Boost Mode Technology.

Turbo Boost Mode allows processor cores to run faster than marked fre-quency in specific conditions. The default value is [Enabled].

CPU Thermal Throttling You may select [Enabled] to enable CPU internal thermal control mechanism to keep the CPU from overheating.

Please note that enabling this function may reduce CPU voltage and lead to system stability or compatibility issues with some power supplies. Please set this item to

[Disabled] if above issues occur.


36 37

Engl

ish

6.3.2 Chipset Configuration

VT-d Use this to enable or disable Intel® VT-d technology (Intel® Virtualization Technology for Directed I/O). The default value of this feature is [Disabled]. Share Memory Configure the size of memory that is allocated to the integrated graphics processor when the system boots up. Onboard LAN1

This allows you to enable or disable the Onboard LAN1 feature. Onboard LAN2

This allows you to enable or disable the Onboard LAN2 feature. Onboard HD Audio

Enable/disable onboard HD audio. Set to Auto to enable onboard HD au-dio and automatically disable it when a sound card is installed.

Restore on AC/Power LossSelect the power state after a power failure. If [Power Off] is selected, the power will remain off when the power recovers. If [Power On] is selected, the system will start to boot up when the power recovers.

38 39

English

6.3.3 Storage Configuration

SATA Controller(s) Use this item to enable or disable the SATA Controller feature.SATA Mode Selection Use this to select SATA mode. The default value is [AHCI Mode].

AHCI (Advanced Host Controller Interface) supports NCQ and other new features that will improve SATA disk perfor-mance but IDE mode does not have these advantages.

SATA Aggressive Link Power Management Use this item to configure SATA Aggressive Link Power Management.Hard Disk S.M.A.R.T. Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analy-

sis, and Reporting Technology) feature. Configuration options: [Disabled] and [Enabled].


38 39

Engl

ish

6.3.4 Super IO Configuration

COM1 Configuration Use this to set parameters of COM1. Type Select Use this to select COM3 port type: [RS232], [RS422] or [RS485].WDT Timeout Reset Use this to set the Watch Dog Timer.

40 41

English

6.3.5 AMT Configuration

AMT BIOS Features Use this to enable or disable Intel(R) Active Management Technology

BIOS Extension. The default is [Enabled].ASF support Use this to enable or disable Alert Specification Format. The default is [En-

abled].USB Provisioning of AMT Use this to enable or disable AMT USB Provisioning. The default is [Dis-

abled].Secure Erase mode Change Secure Erase module behavior: Simulated: Performs SE flow

without erasing SSD. Real: Erase SSD.Force Secure Erase Use this to enable or disable Force Secure Erase on next boot. The de-

fault is [Disabled].MEBx hotkey Pressed Use this to enable or disable MEBx hotkey press. The default is [Disabled].MEBx Selection Screen Use this to enable or disable MEBx Selection Screen. The default is [Dis-

abled].Hide Un-configure ME Confirmation Prompt Hide Un-Configure ME without password confirmation prompt. The default

is [Disabled].MEBx OEM Debug Menu Enable Use this to enable or disable MEBx OEM Debug Menu. The default is [Dis-

abled].Un-Configure ME Un-Configure ME without password. The default is [Disabled].


40 41

Engl

ish

WatchDog Use this to enable or disable AMT WatchDog Timer. The default is [Dis-

abled].Activate Remote Assistance Process Trigger CIRA boot. The default is [Disabled].PET Progress User can enable or disable PET Events progress to receive PET events or

not. The default is [Enabled].ASF Sensors Table Use this to enable or disable ASF Sensor Table. The default is [Disabled].Non-UI Mode Resolution Use this to set resolution for non-UI text mode.UI Mode Resolution Use this to set resolution for UI text mode.Graphics Mode Resolution Use this to set resolution for graphics mode.

42 43

English

6.3.6 ACPI Configuration

Suspend to RAMUse this item to select whether to auto-detect or disable the Suspend-to-RAM feature. Select [Auto] will enable this feature if the OS supports it.

Onboard LAN Power On Use this item to enable or disable onboard LAN to turn on the system from the power-soft-off mode.RTC Alarm Power On Use this item to enable or disable RTC (Real Time Clock) to power on the

system.


42 43

Engl

ish

6.3.7 USB Configuration

Legacy USB SupportEnable or disable Legacy OS Support for USB 2.0 devices. If you encoun-ter USB compatibility issues it is recommended to disable legacy USB support. Select UEFI Setup Only to support USB devices under the UEFI setup and Windows/Linux operating systems only.

44 45

English

6.3.8 Trusted Computing

Security Device SupportEnable or disable BIOS support for security device.


44 45

Engl

ish

6.4 Hardware Health Event Monitoring ScreenIn this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage.

CPU Fan 1 Setting This allows you to set CPU fan 1’s speed. Configuration options: [Full On]

and [Automatic Mode]. The default value is [Full On].

46 47

English

6.5 Security ScreenIn this section, you may set, change or clear the supervisor/user password for the system.

Supervisor Password Set or change the password for the administrator account. Only the ad-

ministrator has authority to change the settings in the UEFI Setup Utility. Leave it blank and press enter to remove the password.

User Password Set or change the password for the user account. Users are unable to

change the settings in the UEFI Setup Utility. Leave it blank and press en-ter to remove the password.

Secure Boot Enable to support Windows 8.1 / 8 Secure Boot.


46 47

Engl

ish

Boot From Onboard LANUse this item to enable or disable the Boot From Onboard LAN feature.

Setup Prompt TimeoutThis shows the number of seconds to wait for setup activation key. 65535(0XFFFF) means indefinite waiting.

Bootup Num-LockIf this item is set to [On], it will automatically activate the Numeric Lock function after boot-up.

Full Screen Logo Use this item to enable or disable OEM Logo. The default value is [Enabled].

6.6 Boot ScreenIn this section, it will display the available devices on your system for you to config-ure the boot settings and the boot priority.

48 49

English

CSM (Compatibility Support Module)

CSM Enable to launch the Compatibility Support Module. Please do not disable

unless you’re running a WHCK test. If you are using Windows 8.1 64-bit and all of your devices support UEFI, you may also disable CSM for faster boot speed.

Launch PXE OpROM Policy Select UEFI only to run those that support UEFI option ROM only. Select

Legacy only to run those that support legacy option ROM only. Select Do not launch to not execute both legacy and UEFI option ROM.

Launch Video OpROM Policy Select UEFI only to run those that support UEFI option ROM only. Select



48 49

Engl

ish

6.7 Exit Screen

Save Changes and ExitWhen you select this option, it will pop-out the following message, “Save configuration changes and exit setup?” Select [OK] to save the changes and exit the UEFI SETUP UTILITY.

Discard Changes and ExitWhen you select this option, it will pop-out the following message, “Discard changes and exit setup?” Select [OK] to exit the UEFI SETUP UTILITY without saving any changes.

Discard ChangesWhen you select this option, it will pop-out the following message, “Discard changes?” Select [OK] to discard all changes.

Load UEFI Defaults Load UEFI default values for all the setup questions. F9 key can be used for this operation.

Launch EFI Shell from filesystem deviceAttempts to Launch EFI Shell application (Shell64.efi) from one of the available filesystem devices.

50 51

English

Chapter 7 UEFI Setup Utility (NUC BOX 8265U)7.1 IntroductionThis section explains how to use the UEFI SETUP UTILITY to confi gure your system. The UEFI chip on the motherboard stores the UEFI SETUP UTILITY. You may run the UEFI SETUP UTILITY when you start up the computer. Please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter the UEFI SETUP UTILITY, otherwise, POST will continue with its test routines.If you wish to enter the UEFI SETUP UTILITY after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may also restart by turning the system off and then back on.

Because the UEFI software is constantly being updated, the following UEFI setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen.

7.1.1 UEFI Menu Bar The top of the screen has a menu bar with the following selections: Main To set up the system time/date informationAdvanced To set up the advanced UEFI featuresH/W Monitor To display current hardware statusSecurity To set up the security featuresBoot To set up the default system device to locate and load the

Operating SystemExit To exit the current screen or the UEFI SETUP UTILITY Use < > key or < > key to choose among the selections on the menu bar, and then press <Enter> to get into the sub screen. You can also use the mouse to click your required item.

Use < > key or < > key to choose among the selections on the menu Use < > key or < > key to choose among the selections on the menu


50 51

Engl

ish

7.1.2 Navigation Keys Please check the following table for the function description of each navigation key. Navigation Key(s) Function Description / Moves cursor left or right to select Screens / Moves cursor up or down to select items + / - To change option for the selected items<Enter> To bring up the selected screen<F1> To display the General Help Screen<F7> Discard changes<F9> To load optimal default values for all the settings<F10> To save changes and exit the UEFI SETUP UTILITY<F12> Print screen<ESC> To jump to the Exit Screen or exit the current screen

7.2 Main ScreenWhen you enter the UEFI SETUP UTILITY, the Main screen will appear and display the system overview.

52 53

English

Setting wrong values in this section may cause the system to malfunction.

7.3 Advanced ScreenIn this section, you may set the configurations for the following items: CPU Configu-ration, Chipset Configuration, Storage Configuration, Super IO Configuration, ACPI Configuration, USB Configuration and Trusted Computing.

Instant FlashInstant Flash is a UEFI flash utility embedded in Flash ROM. This conve-nient UEFI update tool allows you to update system UEFI without entering operating systems first like MS-DOS or Windows®. Just launch this tool and save the new UEFI file to your USB flash drive, floppy disk or hard drive, then you can update your UEFI only in a few clicks without prepar-ing an additional floppy diskette or other complicated flash utility. Please be noted that the USB flash drive or hard drive must use FAT32/16/12 file system. If you execute Instant Flash utility, the utility will show the UEFI files and their respective information. Select the proper UEFI file to update your UEFI, and reboot your system after UEFI update process completes.


52 53

Engl

ish

7.3.1 CPU Configuration

Intel Hyper Threading Technology To enable this feature, a computer system with an Intel processor that sup-

ports Hyper-Threading technology and an operating system that includes optimization for this technology, such as Microsoft® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit is required. Set to [Enabled] if using Microsoft® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit or Linux kernel version 2.4.18 or higher. This option will be hidden if the installed CPU does not support Hyper-Threading technology.

Active Processor CoresSelect the number of cores to enable in each processor package.

CPU C States SupportEnable CPU C States Support for power saving. It is recommended to keep C3, C6 and C7 all enabled for better power saving.

Intel Virtualization Technology When this option is set to [Enabled], a VMM (Virtual Machine Architecture)

can utilize the additional hardware capabilities provided by Vanderpool Technology. This option will be hidden if the installed CPU does not

support Intel Virtualization Technology.Intel SpeedStep Technology Intel SpeedStep technology is Intel’s new power saving technology. Pro-

cessors can switch between multiple frequencies and voltage points to en-able power saving. The default value is [Enabled]. Configuration options:

[Enabled] and [Disabled]. If you install Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit and want to enable this function, please set this item to [Enabled]. This item will be hidden if the current CPU does not support In-tel SpeedStep technology.

54 55

English

Intel Turbo Boost Technology Use this item to enable or disable Intel Turbo Boost Mode Technology.

Turbo Boost Mode allows processor cores to run faster than marked fre-quency in specific conditions. The default value is [Enabled].

CPU Thermal Throttling You may select [Enabled] to enable CPU internal thermal control mechanism to keep the CPU from overheating.

Please note that enabling this function may reduce CPU voltage and lead to system stability or compatibility issues with some power supplies. Please set this item to

[Disabled] if above issues occur.


54 55

Engl

ish

7.3.2 Chipset Configuration

VT-d Use this to enable or disable Intel® VT-d technology (Intel® Virtualization Technology for Directed I/O). The default value of this feature is [Disabled]. Share Memory Configure the size of memory that is allocated to the integrated graphics processor when the system boots up. Onboard LAN1

This allows you to enable or disable the Onboard LAN1 feature. Onboard LAN2

This allows you to enable or disable the Onboard LAN2 feature. Onboard HD Audio

Enable/disable onboard HD audio. Set to Auto to enable onboard HD au-dio and automatically disable it when a sound card is installed.

Restore on AC/Power LossSelect the power state after a power failure. If [Power Off] is selected, the power will remain off when the power recovers. If [Power On] is selected, the system will start to boot up when the power recovers.

56 57

English

7.3.3 Storage Configuration

SATA Controller(s) Use this item to enable or disable the SATA Controller feature.SATA Mode Selection Use this to select SATA mode. The default value is [AHCI Mode].

AHCI (Advanced Host Controller Interface) supports NCQ and other new features that will improve SATA disk perfor-mance but IDE mode does not have these advantages.

SATA Aggressive Link Power Management Use this item to configure SATA Aggressive Link Power Management.Hard Disk S.M.A.R.T. Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analy-

sis, and Reporting Technology) feature. Configuration options: [Disabled] and [Enabled].


56 57

Engl

ish

7.3.4 Super IO Configuration

COM1 Configuration Use this to set parameters of COM1. Type Select Use this to select COM3 port type: [RS232], [RS422] or [RS485].WDT Timeout Reset Use this to set the Watch Dog Timer.

58 59

English

7.3.5 ACPI Configuration

Suspend to RAMUse this item to select whether to auto-detect or disable the Suspend-to-RAM feature. Select [Auto] will enable this feature if the OS supports it.

Onboard LAN Power On Use this item to enable or disable onboard LAN to turn on the system from the power-soft-off mode.RTC Alarm Power On Use this item to enable or disable RTC (Real Time Clock) to power on the

system.


58 59

Engl

ish

7.3.6 USB Configuration

Legacy USB SupportEnable or disable Legacy OS Support for USB 2.0 devices. If you encoun-ter USB compatibility issues it is recommended to disable legacy USB support. Select UEFI Setup Only to support USB devices under the UEFI setup and Windows/Linux operating systems only.

60 61

English

7.3.7 Trusted Computing

Security Device SupportEnable or disable BIOS support for security device.


60 61

Engl

ish

7.4 Hardware Health Event Monitoring ScreenIn this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage.

CPU Fan 1 Setting This allows you to set CPU fan 1’s speed. Configuration options: [Full On]

and [Automatic Mode]. The default value is [Full On].

62 63

English

7.5 Security ScreenIn this section, you may set, change or clear the supervisor/user password for the system.

Supervisor Password Set or change the password for the administrator account. Only the ad-

ministrator has authority to change the settings in the UEFI Setup Utility. Leave it blank and press enter to remove the password.

User Password Set or change the password for the user account. Users are unable to

change the settings in the UEFI Setup Utility. Leave it blank and press en-ter to remove the password.

Secure Boot Enable to support Windows 8.1 / 8 Secure Boot.


62 63

Engl

ish

Boot From Onboard LANUse this item to enable or disable the Boot From Onboard LAN feature.

Setup Prompt TimeoutThis shows the number of seconds to wait for setup activation key. 65535(0XFFFF) means indefinite waiting.

Bootup Num-LockIf this item is set to [On], it will automatically activate the Numeric Lock function after boot-up.

Full Screen Logo Use this item to enable or disable OEM Logo. The default value is [Enabled].

7.6 Boot ScreenIn this section, it will display the available devices on your system for you to config-ure the boot settings and the boot priority.

64 65

English

CSM (Compatibility Support Module)

CSM Enable to launch the Compatibility Support Module. Please do not disable

unless you’re running a WHCK test. If you are using Windows 8.1 64-bit and all of your devices support UEFI, you may also disable CSM for faster boot speed.

Launch PXE OpROM Policy Select UEFI only to run those that support UEFI option ROM only. Select


Launch Video OpROM Policy Select UEFI only to run those that support UEFI option ROM only. Select



64 65

Engl

ish

7.7 Exit Screen

Save Changes and ExitWhen you select this option, it will pop-out the following message, “Save configuration changes and exit setup?” Select [OK] to save the changes and exit the UEFI SETUP UTILITY.

Discard Changes and ExitWhen you select this option, it will pop-out the following message, “Discard changes and exit setup?” Select [OK] to exit the UEFI SETUP UTILITY without saving any changes.

Discard ChangesWhen you select this option, it will pop-out the following message, “Discard changes?” Select [OK] to discard all changes.

Load UEFI Defaults Load UEFI default values for all the setup questions. F9 key can be used for this operation.

Launch EFI Shell from filesystem deviceAttempts to Launch EFI Shell application (Shell64.efi) from one of the available filesystem devices.

66 PB

English

Chapter 8 Software Support8.1 Install Operating System This motherboard supports various Microsoft® Windows® operating systems: 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit. Because motherboard settings and hard-ware options vary, use the setup procedures in this chapter for general reference only. Refer your OS documentation for more information.

8.2 Support CD InformationThe Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard’s features.

8.2.1 Running The Support CD To begin using the support CD, insert the CD into your CD-ROM drive. The CD automatically displays the Main Menu if “AUTORUN” is enabled in your computer. If the Main Menu did not appear automatically, locate and double click on the file “ASRSETUP.EXE” from the BIN folder in the Support CD to display the menus.

8.2.2 Drivers MenuThe Drivers Menu shows the available device’s drivers if the system detects installed devices. Please install the necessary drivers to activate the devices. 8.2.3 Utilities MenuThe Utilities Menu shows the application software that the motherboard sup-ports. Click on a specific item then follow the installation wizard to install it.

8.2.4 Contact InformationIf you need to contact ASRock or want to know more about ASRock, you’re welcome to visit ASRock’s website at http://www.asrock.com; or you may con-tact your dealer for further information.

nuc box 8265u nuc box 8365ue user manual - asrockdownload.asrock.com/ipc/manual/nuc box...

Documents