nokia ultrasite support installation overview

Nokia UltraSite Support User Manual

Nokia UltraSite SupportInstallation Overview

User Manual

CDPFULS015

DN00241232 © Nokia Networks Oy 1 (20)Issue 1 en Nokia Proprietary and Confidential

Nokia UltraSite Support Installation Overview

The information in this document is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This document is intended for theuse of Nokia Networks' customers only for the purposes of the agreement under which thedocument is submitted, and no part of it may be reproduced or transmitted in any form ormeans without the prior written permission of Nokia Networks. The document has beenprepared to be used by professional and properly trained personnel, and the customerassumes full responsibility when using it. Nokia Networks welcomes customer comments aspart of the process of continuous development and improvement of the documentation.

The information or statements given in this document concerning the suitability, capacity, orperformance of the mentioned hardware or software products cannot be considered bindingbut shall be defined in the agreement made between Nokia Networks and the customer.However, Nokia Networks has made all reasonable efforts to ensure that the instructionscontained in the document are adequate and free of material errors and omissions. NokiaNetworks will, if necessary, explain issues which may not be covered by the document.

Nokia Networks' liability for any errors in the document is limited to the documentary correctionof errors. Nokia Networks WILL NOT BE RESPONSIBLE IN ANY EVENT FOR ERRORS INTHIS DOCUMENT OR FOR ANY DAMAGES, INCIDENTAL OR CONSEQUENTIAL(INCLUDING MONETARY LOSSES), that might arise from the use of this document or theinformation in it.

This document and the product it describes are considered protected by copyright according tothe applicable laws.

NOKIA logo is a registered trademark of Nokia Corporation.

Other product names mentioned in this document may be trademarks of their respectivecompanies, and they are mentioned for identification purposes only.

Copyright © Nokia Networks Oy 2001. All rights reserved.

2 (20) © Nokia Networks Oy DN00241232Nokia Proprietary and Confidential Issue1 en

Contents

Contents 3

1 About this document 5

2 Working order 7

3 Support delivery contents 93.1 Cabinet delivery contents 93.1.1 Cabinet core 93.1.2 Support cabinet application kits 103.2 Unit delivery contents 133.2.1 Common items 143.2.2 Additional items 143.2.3 Options 14

4 Unpacking and inspecting the Support delivery 15

5 Installation tools and equipment 17


About this document

1 About this documentPurpose

This document gives an overview of the tasks you will need to perform to installthe Nokia UltraSite Support.

Contents

This document contains the following information:

• Chapter 2: Working order

• Chapter 3: Support delivery contents

• Chapter 4: Unpacking and inspecting the Support delivery

• Chapter 5: Installation tools and equipment

Readership

The following personnel should read Nokia UltraSite Support InstallationOverview:

• installation engineers

• commissioning engineers


Working order

Note

2 Working orderThis chapter describes the working order for the installation of Nokia UltraSiteSupport.

To complete the installation of the Support, proceed in the followingworking order:

1. Complete the site planning according to the specifications provided inNokia UltraSite Support Requirements for Installation and Operation.

2. Prepare the site for installation and complete the site survey.

3. Ensure the proper installation tools and equipment are onsite.

4. Unpack and inspect the contents of the Support delivery for any visibledamage. Refer to Unpacking and Inspecting the Support Delivery for moreinformation.

5. Check the completeness of the cabinet delivery using the packing list.

If the contents of the cabinet delivery are damaged or missing, immediately reportthese findings to your local Nokia representative.

6. Store the packing list in the site folder.

7. Install the cabinet core to the base (Indoor cabinet) or plinth (Outdoorcabinet).

8. Install the cabinet application kits to the cabinet core.

9. Route external cabinet interface cables to the cabinet.

10. Install plug-in units and any optional units to the cabinet core.



11. Connect the cables of the plug-in units and route according to the cabinetconfiguration.

12. Complete the installation checklist and place in the site folder.

13. Commission and integrate the Support. Refer to Nokia UltraSite SupportCommissioning.

14. Complete the Support commissioning and integration checklists and placein the site folder.

15. Recycle the packing material.


Support delivery contents

3 Support delivery contentsThis chapter identifies the contents of Nokia UltraSite Support transportationpackage.

The Support transportation package contains the following:

• cabinet delivery

• unit delivery

3.1 Cabinet delivery contents

The cabinet delivery includes the following:

• a Support cabinet core for the Indoor or Outdoor cabinet (CRMB), withADUB and BATA backplanes pre-installed

• a cabinet application kit (IAKA or OAKA)

• cable kits (optional)

3.1.1 Cabinet core

The cabinet core houses the plug-in units and temperature control system. Thecabinet application kits define the type of cabinet delivery (Indoor or Outdoor).

Figure 1 illustrates the cabinet core of the Nokia Ultrasite Support Indoor andOutdoor.



Figure 1. Cabinet core (Indoor or Outdoor)

3.1.2 Support cabinet application kits

Indoor Application Kit

The Indoor Application Kit (IAKA) consists of the following modules:

• a door

• a roof

• required mounting hardware (feet)

Figure 2 illustrates the modules of the IAKA with the cabinet core.

00296576



Figure 2. Modules of the IAKA shown with the cabinet core

Outdoor Application Kit

The Outdoor Application Kit (OAKA) consists of the following modules:

• a plinth for one cabinet

• a back wall

• two side walls

• a door frame

KEY:1. Feet2. Roof3. Door

2

3

1

00296591

(4 places)

Lifting eye bolts (4 places)

Cabinet core (CRMx)



• a door with a preinstalled Cabinet Cooling fan

• a roof

• required mounting hardware

You can also install an optional Heater unit (HETA) in the OAKA door.

Figure 3 illustrates the components of the OAKA with the cabinet core.



Figure 3. Modules of the OAKA shown with the cabinet core

3.2 Unit delivery contents

The ADUB is the only unit pre-installed in the cabinet. For instructions on howto install units, refer to Nokia UltraSite Support Unit Installation and Cables.

2

6

00296607

KEY:1. Back wall2. Side wall3. Door frame4. Plinth5. Roof6. Door

5

3

6

4

1

2

Lifting eye bolts (4 places)

Cabinet core (CRMx)



Where required, cable kits accompany the units in the Support transportationpackage. For instructions on how to route unit cables, refer to Nokia UltraSiteSupport Unit Installation and Cables.

3.2.1 Common items

Nokia UltraSite Support configurations contain the following common units:

• AC / DC unit (ADUB) (pre-installed)

• either six or twelve BATA rectifier units (BATA backplanes pre-installed)

• up to three battery trays in the basic cabinet, or four in the battery extensioncabinet

3.2.2 Additional items

The Nokia UltraSite Support Outdoor cabinets can also contain the followingunits:

• LTED box, enclosure for up to 4U height of customer equipment

• LTEE box, enclosure for up to 10U height of customer equipment

• Standard Equipment Kit (SEK) A (19”, 6U). These can be installed aboveeach other to create up to 18U space capacity.

3.2.3 Options

The following are options for the Nokia UltraSite Support Indoor and Outdoorcabinets:

• Over-Voltage Protection (OVP)

• Battery heater matt (HETB)

• earthquake accessories


Unpacking and inspecting the Support delivery

WARNING

Caution

4 Unpacking and inspecting the Supportdelivery

This chapter describes how to unpack and inspect the contents of the Supporttransportation delivery packages.

A basic cabinet core as delivered weighs 74 kg (164 lb) approximately.Lifting the cabinet core requires a minimum of two installation personnel!

To unpack and inspect the cabinet delivery:

1. Lift the cabinet core from the transportation package.

2. Remove the cardboard and plastic wrapping from around the cabinet core.

Do not place the Support in a vertical position when removing from thetransportation package. Place the Support on the packing material in a horizontalposition.

3. Remove the desiccant packs.

4. Inspect the cabinet core for any visible damage.

5. Unpack and inspect the contents of the cabinet kit for any visible damage.



Note

6. Check the completeness of the cabinet delivery using the packing list.

If the contents of the cabinet delivery are damaged or missing, immediately reportthese findings to your local Nokia representative.

7. Store the packing list in the site folder.

8. Recycle the packing material.


Installation tools and equipment

Note

5 Installation tools and equipmentThis chapter describes the equipment Nokia recommends for installing themodules and cables of the cabinet and plug-in units.

Table 1 lists the European and US specifications for standard tools and equipmentyou will need during installation of the Nokia UltraSite Support.

Nokia does not include the tools and equipment in the Support delivery package.

Table 1. Standard installation tools

European specified US specified

Antistatic hand strap and cable

Automatic puncher to mark hole places

Cable cutters, 2.5-50 mm2 8” electricians cable cutters

Cable stripper for 0.25 and 0.4 mm2 wire Generic - standard electricians wirestrippers

Cable stripper for 2.5 to 50 mm2 wire Cable stripping knife - Klein, Clauss,Ideal, etc.

Cable ties for routing cables

Caliper square, 160 mm Generic - 6” square, adjustable

Coaxial cable stripper for 75 Ω transmission cables

Combi ring-ended spanner, 7 mm, 8 mm,9 mm, 10 mm, 11 mm, 12 mm, 13 mm, 15mm, 17 mm

Metric combination wrench set

Drill with Screwdriver bit set, 16 pcs Drill, 1/4” drive (Torx 20)

1/4” hex drive (Torx 25)

Crimping tool for grounding cable shoes



Drill bit set, 1 to13 mm Generic

Extension cord 115 VAC

Flashlight, pocket lamp or torch Flashlight, Maglite

Grounding kit Generic

Hammer Generic 1.5“

Hammer drill, 12.0*260 Drill bit, 1/2” x 10 Hammer drill, 12.0*260 Drill bit, 1/2” x 10

Insulated wrench for installing batteries

Insulated side cutters

Ladder

Lifting eye bolts, 4 pcs, M12 (optional)

Marker pen or comparable tool

Multimeter, Fluke 77 or equal Multimeter, Fluke 77 or equal

Pliers:

• Electric pliers, 115 mm

• Flatnose pliers, 210 mm

• Multigrip pliers, 250 mm

Pliers:

• 4.5" needlenose pliers

• 8" standard pliers

• 10" vise-grips

Right angle 10" right angle or equal

Safety glasses

Scissors, Fiskars 9891 or equal Scissors, Fiskars 9891 or equal

Screwdriver set:

• flathead

• crosshead

SMA torque wrench 1 Nm (0.74 ft-lb) / 0.45 Nm (0.33 ft-lb)

Socket wrench and sets:

• Socket wrench (10 - 19 mm) andextension socket

Socket sets, metric 1/4” drive

Socket sets, metric 3/8” drive

Spirit level for measuring if BTS is level toground

Basic level

Tape measure, 3 m and 5 m Generic - metric/standard readings, 10 ft.and 16 ft.

TORX screwdriver set, TX 20 for unit installation

Table 1. Standard installation tools (Continued)



Installation tools and equipment

Utility knife

Wrench, adjustable 8”

Wrench set, metric combo, 10...19 mm

Table 1. Standard installation tools (Continued)



nokia ultrasite support installation overview

Documents