nanobridge m qsg
TRANSCRIPT
-
8/12/2019 NanoBridge M QSG
1/20
Models:NanoBridge M
NB-2G18
NB-5G22
NB-5G25
NanoBridge
-
8/12/2019 NanoBridge M QSG
2/20
-
8/12/2019 NanoBridge M QSG
3/20
1
Typical Deployment
Typical Deployment
LAN or Computer to
Ethernet Port labeled
LAN on PoE Adapter
Ethernet Port on Ubiquiti
Device to Ethernet Port labeled
POE on PoE Adapter
Connect the Power Cord to the
PoE Adapter and a power outlet
Note:Shielded Category 5 (or above) cabling should beused for all wired Ethernet connections and should begrounded through the AC ground of the PoE.
-
8/12/2019 NanoBridge M QSG
4/20
2
NanoBridgeM Quick Start Guide
Application Examples
airGrid/NanoBridge mounted outdoors without the grid or dishinstalled provides outdoor to indoor coverage using the 3dBi feed
antenna only.
airGrid/NanoBridge mounted outdoors with the grid or dishrefelector installed provides directional outdoor coverage (gainreflector dependent)
-
8/12/2019 NanoBridge M QSG
5/20
3
NanoBridge Installation
NanoBridge Installation
These instructions cover the NanoBridge M, NB-2G18, NB-5G22,and NB-5G25.
Package Contents
Parabolic Reflector/Dish Antenna Feed Feed Support Dish Bracket
Pole BracketClamp
M6 U-Bolt(Qty. 2)
M6x12 CarriageBolt (Qty. 4)
M6 SerratedFlange Nut (Qty. 6)
Feed SupportBushing
M6 Bolt-Spring-LockWasher Assembly (Qty. 4)
* Products may be different from pictures and are subject to change without notice.
Installation Requirements 10 mm wrench
Installation
1. Install the Feed Supportinto the Dish Bracketusing four M6 Bolt-Spring-Lock-Washer Assemblies.
-
8/12/2019 NanoBridge M QSG
6/20
4
NanoBridgeM Quick Start Guide
2. Install the Dish Bracketto the Dish using four M6x12 CarriageBoltsand four M6 Serrated Flange Nuts.
3. Route the Ethernet cable through the bottom hole of the FeedSupportand connect it to the Ethernet port on the back of theAntenna Feed.
4. Insert theAntenna Feedinto the Feed Supportwith theorientation as shown in the image below.
-
8/12/2019 NanoBridge M QSG
7/20
5
NanoBridge Installation
5. Wrap the Feed Support Bushingaround the Ethernet cable andthen push it into place in the Feed Support.
6. Attach theAntennato the pole using the two M6 U-Bolts, thetwo Pole Bracket Clamps, and four M6 Serrated Flange Nuts.
The mounting bracket can accomodate 1.25" - 2.2" pole.
-
8/12/2019 NanoBridge M QSG
8/20
6
NanoBridgeM Quick Start Guide
Accessing airOS
Connect to the airOS Configuration Interface.
1. Make sure that your host machine is connected to the LAN thatis connected to the device.
2. Configure the Ethernet adapter on your host system with astatic IP address on the 192.168.1.x subnet (e.g., 192.168.1.100).
3. Launch your Web browser. Type http://192.168.1.20in theaddress field and press enter(PC) or return(Mac).
4. The login screen will appear. Enter ubntin the UsernameandPasswordfields. Select your Countryand Language. You mustagree to the Terms of Useto use the product. Click Login.
Note:U.S. product versions are locked to the U.S. CountryCode to ensure compliance with FCC regulations.
The airOS Configuration Interface will appear allowing you to
customize your settings as needed.
-
8/12/2019 NanoBridge M QSG
9/20
7
Ubiquiti Networks Wiki and Forum
Ubiquiti Networks Wiki and Forum
Ubiquiti Networks has an online Wiki with Manuals, Guides, andInformation. It is located at www.ubnt.com/wiki.
Another great resource is the Ubiquiti Networks Forum. You canpost and view comments, questions, and answers with otherforum members and Ubiquiti staff at www.ubnt.com/forum.
-
8/12/2019 NanoBridge M QSG
10/20
8
NanoBridgeM Quick Start Guide
General WarrantyUBIQUITI NETWORKS, Inc (UBIQUITI NETWORKS) represents andwarrants that the Products furnished hereunder shall be free from defects
in material and workmanship for a period of one (1) year from the dateof shipment by UBIQUITI NETWORKS under normal use and operation.UBIQUITI NETWORKS sole and exclusive obligation under the foregoingwarranty shall be to repair or replace, at its option, any defective Productthat fails during the warranty period. The expense of removal andreinstallation of any item is not included in this warranty.
The foregoing warranty is exclusive and in lieu of all other warranties,express or implied, including the implied warranties of merchantabilityand fitness for a particular purpose and any warranties arising from a
course of dealing, usage or trade practice with respect to the products.Repair or replacement in the manner provided herein shall be the soleand exclusive remedy of Buyer for breach of warranty and shall constitutefulfillment of all liabilities of UBIQUITI NETWORKS with respect to thequality and performance of the Products. UBIQUITI NETWORKS reservesthe right to inspect all defective Products (which must be returned byBuyer to UBIQUITI NETWORKS factory freight prepaid).
No Products will be accepted for replacement or repair without obtaininga Return Materials Authorization (RMA) number from UBIQUITI NETWORKS.
Products returned without an RMA number will not be processed and willbe returned to Buyer freight collect. UBIQUITI NETWORKS shall have noobligation to make repairs or replacement necessitated by catastrophe,fault, negligence, misuse, abuse, or accident by Buyer, Buyers customers orany other parties. The warranty period of any repaired or replaced. Productshall not extend beyond its original term.
Warranty Conditions
The foregoing warranty shall apply only if:(V) The Product has not been subjected to misuse, neglect or unusual
physical, electrical or electromagnetic stress, or some other type ofaccident.
(VI) No modification, alteration or addition has been made to the Productby persons other than UBIQUITI NETWORKS or UBIQUITI NETWORKSauthorized representatives or otherwise approved by UBIQUITINETWORKS.
(VII) The Product has been properly installed and used at all times inaccordance, and in all material respects, with the applicable Productdocumentation.
(VIII) All Ethernet cabling runs use CAT5 (or above) shielded cabling.
Disclaimer: UBIQUITI NETWORKS does not warrant that the operation ofthe products is error-free or that operation will be uninterrupted. In noevent shall UBIQUITI NETWORKS be responsible for damages or claimsof any nature or description relating to system performance, including
coverage, buyers selection of products for buyers application and/orfailure of products to meet government or regulatory requirements.
-
8/12/2019 NanoBridge M QSG
11/20
9
Safety Notices
Returns
In the unlikely event a defect occurs, please work through the dealer ordistributor from which this product was purchased.
Safety Notices1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING:Do not use this product in location that can
be submerged by water.
WARNING:Avoid using this product during an electricalstorm. There may be a remote risk of electric shock fromlightning.
Electrical Safety Information1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturers label. Connection to adifferent power source than those specified may result in improperoperation, damage to the equipment or pose a fire hazard if thelimitations are not followed.
2. There are no operator serviceable parts inside this equipment. Serviceshould be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which hasan integral safety ground wire intended for connection to a groundedsafety outlet.
a. Do not substitute the power cord with one that is not the providedapproved type. Never use an adapter plug to connect to a 2-wireoutlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of thesafety certification, modification or misuse can provide a shockhazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there arequestions about the installation prior to connecting the equipment.
d. Protective earthing is provided by Listed AC adapter. Buildinginstallation shall provide appropriate short-circuit backupprotection.
e. Protective bonding must be installed in accordance with localnational wiring rules and regulations.
-
8/12/2019 NanoBridge M QSG
12/20
10
NanoBridgeM Quick Start Guide
Compliance
FCC
Changes or modifications not expressly approved by the party responsiblefor compliance could void the users authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, includinginterference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with thelimits for a Class A digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference when the equipment is operated in a commercialenvironment. This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in accordance withthe instruction manual, may cause harmful interference to radiocommunications. Operations of this equipment in a residential area is likelyto cause harmful interference in which case the user will be required to
correct the interference at his own expense.For MPE and antenna usage details, please visit our website atwww.ubnt.com/products
Industry Canada
This Class A digital apparatus complies with Canadian ICES-003.
To reduce potential radio interference to other users, the antennatype and its gain should be so chosen that the equivalent isotropicallyradiated power (e.i.r.p.) is not more than that permitted for successfulcommunication.
This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference thatmay cause undesired operation of the device.
Cet appareil numrique de la classe A est confrome la norme NMB-003Canada.
Pour rduire le risque dinterfrence aux autres utilisateurs, le typedantenne et son gain doivent tre choisies de faon que la puissanceisotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est ncessairepour une communication russie.
-
8/12/2019 NanoBridge M QSG
13/20
11
CE Marking
Cet appareil est conforme la norme RSS Industrie Canada exempts delicence norme(s). Son fonctionnement est soumis aux deux conditionssuivantes:
1. Cet appareil ne peut pas provoquer dinterfrences et
2. Cet appareil doit accepter toute interfrence, y compris lesinterfrences qui peuvent causer un mauvais fonctionnement dudispositif.
RF Exposure Warning
The antennas used for this transmitter must be installed to provide aseparation distance of at least 20 cm from all persons and must not be
located or operating in conjunction with any other antenna or transmitter.Les antennes utilises pour ce transmetteur doivent tre install enconsidrant une distance de sparation de toute personnes d'au moins20 cm et ne doivent pas tre localis ou utilis en conflit avec tout autreantenne ou transmetteur.
CE MarkingCE marking on this product represents the product is in compliance with
all directives that are applicable to it.
Alert sign! Follows CE marking
Alert sign must be indicated if a restriction on use applied to the productand it must follow the CE marking.
-
8/12/2019 NanoBridge M QSG
14/20
12
NanoBridgeM Quick Start Guide
RoHS/WEEE Compliance Statement
EnglishEuropean Directive 2002/96/EC requires that the equipment bearingthis symbol on the product and/or its packaging must not be disposedof with unsorted municipal waste. The symbol indicates that thisproduct should be disposed of separately from regular household waste
streams. It is your responsibility to dispose of this and other electric andelectronic equipment via designated collection facilities appointed by thegovernment or local authorities. Correct disposal and recycling will helpprevent potential negative consequences to the environment and humanhealth. For more detailed information about the disposal of your oldequipment, please contact your local authorities, waste disposal service, orthe shop where you purchased the product.
Deutsch
Die Europische Richtlinie 2002/96/EC verlangt, dass technischeAusrstung, die direkt am Gert und/oder an der Verpackung mit diesemSymbol versehen ist , nicht zusammen mit unsortiertem Gemeindeabfallentsorgt werden darf. Das Symbol weist darauf hin, dass das Produktvon regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegtin Ihrer Verantwortung, dieses Gert und andere elektrische undelektronische Gerte ber die dafr zustndigen und von der Regierungoder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen.Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentiellenegative Folgen fr Umwelt und die menschliche Gesundheit zuvermeiden. Wenn Sie weitere Informationen zur Entsorgung IhrerAltgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oderstdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie dasProdukt erworben haben.
EspaolLa Directiva 2002/96/CE de la UE exige que los equipos que lleven estesmbolo en el propio aparato y/o en su embalaje no deben eliminarse
junto con otros residuos urbanos no seleccionados. El smbolo indicaque el producto en cuestin debe separarse de los residuos domsticosconvencionales con vistas a su eliminacin. Es responsabilidad suyadesechar este y cualesquiera otros aparatos elctricos y electrnicos atravs de los puntos de recogida que ponen a su disposicin el gobierno ylas autoridades locales. Al desechar y reciclar correctamente estos aparatosestar contribuyendo a evitar posibles consecuencias negativas para elmedio ambiente y la salud de las personas. Si desea obtener informacinms detallada sobre la eliminacin segura de su aparato usado, consulte alas autoridades locales, al servicio de recogida y eliminacin de residuos desu zona o pregunte en la tienda donde adquiri el producto.
-
8/12/2019 NanoBridge M QSG
15/20
13
Franais
FranaisLa directive europenne 2002/96/CE exige que lquipement sur lequelest appos ce symbole sur le produit et/ou son emballage ne soit pas jet
avec les autres ordures mnagres. Ce symbole indique que le produitdoit tre limin dans un circuit distinct de celui pour les dchets desmnages. Il est de votre responsabilit de jeter ce matriel ainsi que toutautre matriel lectrique ou lectronique par les moyens de collecteindiqus par le gouvernement et les pouvoirs publics des collectivitsterritoriales. Llimination et le recyclage en bonne et due forme ont pourbut de lutter contre limpact nfaste potentiel de ce type de produitssur lenvironnement et la sant publique. Pour plus dinformations sur lemode dlimination de votre ancien quipement, veuillez prendre contactavec les pouvoirs publics locaux, le service de traitement des dchets, oulendroit o vous avez achet le produit.
ItalianoLa direttiva europea 2002/96/EC richiede che le apparecchiaturecontrassegnate con questo simbolo sul prodotto e/o sullimballaggio nonsiano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indicache questo prodotto non deve essere smaltito insieme ai normali rifiutidomestici. responsabilit del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante le specifichestrutture di raccolta indicate dal governo o dagli enti pubblici locali. Ilcorretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenzepotenzialmente negative per lambiente e per la salute dellessere umano.Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchieapparecchiature in Vostro possesso, Vi invitiamo a contattare gli entipubblici di competenza, il servizio di smaltimento rifiuti o il negozio nelquale avete acquistato il prodotto.
-
8/12/2019 NanoBridge M QSG
16/20
14
NanoBridgeM Quick Start Guide
Declaration of Conformity
esky[Czech]
UBIQUITI NETWORKS tmto prohla uje, e tento UBIQUITINETWORKS device, je ve shod se zkladnmi po adavky a dal mi p
slu n mi ustanovenmi sm rnice 1999/5/ES.
Dansk[Danish]
Undertegnede UBIQUITI NETWORKS erklrer herved, at flgendeudstyr UBIQUITI NETWORKS device, overholder de vsentlige kravog vrige relevante krav i direktiv 1999/5/EF.
Nederlands[Dutch]
Hierbij verklaart UBIQUITI NETWORKS dat het toestel UBIQUITINETWORKS device, in overeenstemming is met de essentile eisenen de andere relevante bepalingen van richtlijn 1999/5/EG.
Bij deze verklaart UBIQUITI NETWORKS dat deze UBIQUITI
NETWORKS device, voldoet aan de essentile eisen en aan deoverige relevante bepalingen van Richtlijn 1999/5/EC.
English Hereby, UBIQUITI NETWORKS, declares that this UBIQUITINETWORKS device, is in compliance with the essentialrequirements and other relevant provisions of Directive 1999/5/EC.
Eesti[Estonian]
Kesolevaga kinnitab UBIQUITI NETWORKS seadme UBIQUITINETWORKS device, vastavust direktiivi 1999/5/E phinuetele janimetatud direktiivist tulenevatele teistele asjakohastele stetele.
Suomi[Finnish] UBIQUITI NETWORKS vakuuttaa tten ett UBIQUITI NETWORKSdevice, tyyppinen laite on direktiivin 1999/5/EY oleellistenvaatimusten ja sit koskevien direktiivin muiden ehtojenmukainen.
Franais[French]
Par la prsente UBIQUITI NETWORKS dclare que lappareilUBIQUITI NETWORKS, device est conforme aux exigencesessentielles et aux autres dispositions pertinentes de la directive1999/5/CE.
Deutsch
[German]
Hiermit erklrt UBIQUITI NETWORKS, dass sich diese UBIQUITI
NETWORKS device, in bereinstimmung mit den grundlegendenAnforderungen und den anderen relevanten Vorschriften derRichtlinie 1999/5/EG befindet. (BMWi)
[Greek]
UBIQUITI NETWORKS UBIQUITINETWORKS device, 1995/5/.
Magyar[Hungarian]
Alulrott, UBIQUITI NETWORKS nyilatkozom, hogy aUBIQUITI NETWORKS device, megfelel a vonatkoz alapvet
kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak.
slenska[Icelandic]
Hr me l sir UBIQUITI NETWORKS yfir v a UBIQUITI NETWORKSdevice, er samrmi vi grunnkrfur og a rar krfur, sem ger ar eru tilskipun 1999/5/EC.
Italiano[Italian]
Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITINETWORKS device, conforme ai requisiti essenziali ed alle altredisposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
-
8/12/2019 NanoBridge M QSG
17/20
15
Declaration of Conformity
Latviski[Latvian]
Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device,atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saisttajiem noteikumiem.
Lietuvikai
[Lithuanian]
UBIQUITI NETWORKS deklaruoja, kad is UBIQUITI NETWORKS
renginys atitinka esminius reikalavimus ir kitas 1999/5/EBDirektyvos nuostatas.
Malti[Maltese]
Hawnhekk, UBIQUITI NETWORKS, jiddikjara li dan UBIQUITINETWORKS device, jikkonforma mal- ti ijiet essenzjali u maprovvedimenti o rajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Norsk[Norwegian]
UBIQUITI NETWORKS erklrer herved at utstyret UBIQUITINETWORKS device, er i samsvar med de grunnleggende krav ogvrige relevante krav i direktiv 1999/5/EF.
Slovensky[Slovak]UBIQUITI NETWORKS t mto vyhlasuje, e UBIQUITI NETWORKSdevice, sp a zkladn po iadavky a v etky prslu n ustanoveniaSmernice 1999/5/ES.
Svenska[Swedish]
Hrmed intygar UBIQUITI NETWORKS att denna UBIQUITINETWORKS device, str I verensstmmelse med de vsentligaegenskapskrav och vriga relevanta bestmmelser som framgr avdirektiv 1999/5/EG.
Espaol[Spanish]
Por medio de la presente UBIQUITI NETWORKS declara que elUBIQUITI NETWORKS device, cumple con los requisitos esenciales
y cualesquiera otras disposiciones aplicables o exigibles de laDirectiva 1999/5/CE.
Polski[Polish]
Niniejszym, firma UBIQUITI NETWORKS o wiadcza, e produkt seriiUBIQUITI NETWORKS device, spenia zasadnicze wymagania i inneistotne postanowienia Dyrektywy 1999/5/EC.
Portugus[Portuguese]
UBIQUITI NETWORKS declara que este UBIQUITI NETWORKS device,est conforme com os requisitos essenciais e outras disposies daDirectiva 1999/5/CE.
Romn[Romanian] Prin prezenta, UBIQUITI NETWORKS declar c acest dispozitivUBIQUITI NETWORKS este n conformitate cu cerinele eseniale ialte prevederi relevante ale Directivei 1999/5/CE.
-
8/12/2019 NanoBridge M QSG
18/20
JL032712
EnglishWe recommend that you protect your networksfrom the most brutal environments anddevastating ESD attacks with industrial-gradeshielded Ethernet cable from Ubiquiti Networks.For more details, visit www.ubnt.com/toughcable
DeutschSchtzen Sie Ihre Netzwerke vor extremen Umwelteinflssenund verheerender elektrostatischer Entladung (ESD), indemSie abgeschirmte Ethernetkabel in Unternehmensqualitt vonUbiquiti Networks verwenden. Weitere Informationen erhalten Sieunter www.ubnt.com/toughcable
EspaolLe recomendamos que proteja sus redes de los entornos mshostiles y los devastadores efectos de las descargas electrostticasutilizando cable Ethernet blindado con calidad-industrial deUbiquiti Networks. Para obtener ms informacin, visitewww.ubnt.com/toughcable
FranaisNous vous recommandons de protger vos rseaux contre lesenvironnements les plus brutaux et les dcharges lectrostatiquesles plus dvastatrices avec un cble Ethernet Ubiquiti Networksavec blindage renforc. Pour en savoir plus, rendez-vous surwww.ubnt.com/toughcable
ItalianoSi consiglia di proteggere le reti dagli ambienti e dagli attacchiESD pi invasivi con il cavo Ethernet schermato-di tipo industrialedi Ubiquiti Networks. Per ulteriori informazioni, visitare il sito Webwww.ubnt.com/toughcable
-
8/12/2019 NanoBridge M QSG
19/20
-
8/12/2019 NanoBridge M QSG
20/20
Ubiquiti Networks Support
Email: [email protected] (9 a.m. - 5 p.m. PST): 408-942-1153
Online Resources
Wiki Page: wiki.ubnt.com
Support Forum: forum.ubnt.com
Downloads: downloads.ubnt.com
w w w . u b n t . c o m
2012 Ubiquiti Networks, Inc. All rights reserved.
http://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdfhttp://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdfhttp://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdfhttp://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdfhttp://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdfhttp://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdfhttp://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdfhttp://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdfhttp://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdfhttp://users/robrohm/Library/Caches/Adobe%20InDesign/Version%207.0/en_US/InDesign%20ClipboardScrap1.pdf