model and die materials
TRANSCRIPT
![Page 1: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/1.jpg)
DEPARTMENT OF PROSTHODONTICS
DR. FEBEL HUDA, M.D.S,DICOI,FICOI,FAD,DLD.ORAL MAXILLOFACIAL PROSTHODONTIST AND IMPLANTOLOGIST DIPLOMATE FROM THE INTERNATIONAL CONGRESS OF ORAL IMPLANTOLOGY FELLOW FROM THE INTERNATIONAL CONGRESS OF ORAL IMPLANTOLOGY DIPLOMATE IN LASER DENTISTRY (UNIVERSITY OF GENOVA - ITALY) FELLOW IN AESTHETIC DENTISTRY (UNIVERSITY OF GREIFSWALD - GERMANY)
![Page 2: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/2.jpg)
MODEL AND DIE MATERIAL
![Page 3: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/3.jpg)
GPT-8• DIE: the positive reproduction of the form of a
prepared tooth in any suitable substance (die is used for construction of cast partial
dentures and crowns)
• MODEL : a facsimile used for display purposes; a miniature representation of something; an example for imitation or emulation.
(model is used for observation, diagnosis, patient education)
![Page 4: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/4.jpg)
MODELS
![Page 5: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/5.jpg)
CLASSIFICATION
MODEL MATERIALS
TYPE II GYPSUM
HEAT ACTIVATED
ACRYLIC
Other model materials:PolycarbonateLead
![Page 6: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/6.jpg)
TYPE II GYPSUM (MODEL PLASTER) (ADA;No: 9)
• USED: For making models and casts.
• REQUIRMENTS:
It should set rapidly but give adequate time for manipulation. It should set to a very hard and strong mass.After mixing, consistency should be such that it can flow into all
parts of the impression and reproduce all the minute details
Craig’s Restorative dental materials -12th Edition
![Page 7: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/7.jpg)
GYPSUMHISTORY :
• Gypsum is found in various part of the world and is a industrial by-product.
• It was used for many centuries for construction purposes.• ALABASTER, a form of white gypsum which was used to
construct KING SOLOMON’S temple.• It was first found in the mines of Paris so called
PLASTER OF PARIS.
Craig’s Restorative dental materials -12th Edition
![Page 8: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/8.jpg)
CLASSIFICATION (according to ADA)
• TYPE – I → Impression plaster. (ADA;No: 4)• TYPE – II → Dental plaster. (ADA;No: 9)• TYPE – III → Dental stone or medium strength stone. (ADA;No: 20)• TYPE – IV → Improved stone or high strength stone (die stone). (ADA;No: 35)• TYPE – V → High strength, high expansion dental stone. (ADA;No: 35)Craig’s Restorative dental materials -12th Edition
![Page 9: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/9.jpg)
CALCINATION
Calcium SulfateHemihydrate
Calcium SulfateDihydrate
Accelerators
Retarders[CaSO4-(2)H2O] + [110˚- 130˚] [CaSO4-(1/2)H2O]
Craig’s Restorative dental materials -12th Edition
![Page 10: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/10.jpg)
Chemical Name: -calcium sulfate
Formula: CaSO4-(1/2)H2O
Powder Shape: Irregular
Density: Porous
Production Steps: Heat to 110C to 130C in air in open kittle
Dental Products: Plaster
Calcination: dry
Common Names: Plaster of Paris
![Page 11: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/11.jpg)
MANIPULATION
Transfer to impression
Craig’s Restorative dental materials -12th Edition
![Page 12: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/12.jpg)
TIME
SETTING STAGES
MixingInterval
WorkingInterval
SettingInterval
MixingTime
00:00:00 00:01:00Working
Time00:07:00
SettingTime
00:13:00
Final Set Setting Time = 45 min
Initial Set Setting Time = 7 – 13min
LOSS OF GLOSS
Craig’s Restorative dental materials -12th Edition
![Page 13: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/13.jpg)
MEASUREMENT OF SETTING TIME
• LOSS OF GLOSS METHOD: The gloss disappears from the surface of plaster mix.
• EXOTHERMIC REACTION: The temperature rise of the mass may also be used for measurement of setting time ,as the setting reaction is exothermic.
• PENETRATION TESTS: By using penetrometer
Craig’s Restorative dental materials -12th Edition
![Page 14: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/14.jpg)
TYPES OF PENETROMETER
VICAT NEEDLE 300gm, 1mm
GILLMORE NEEDLE
LargeGilmoreNeedle
SmallGilmoreNeedle
1/4lb wtdiameter½”
1 lb wtDiameter 1/12”
Craig’s Restorative dental materials -12th Edition
![Page 15: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/15.jpg)
MODEL PASTEREFFECT OF WATER/POWDER RATIO ON SETTING TIME
W/P RATIOml/g
Spatulation turns Initial setting time
0.45 ml/g 100 8 min
0.50 ml/g 100 11 min
0.55 ml/g 100 14 min
![Page 16: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/16.jpg)
MODEL PASTEREFFECT OF SPATULATION ON SETTING TIME
W/P RATIOml/g
Spatulation turns Setting time
0.50 ml/g 20 14 min
0.50 ml/g 100 11 min
0.50 ml/g 200 8 min
![Page 17: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/17.jpg)
SETTING EXPANSION
• Normal setting expansion (0.05 to 0.5%) linear expansion - outward thrust of growth crystals – nuclei
– intermesh - intercepts .
----- Spherulites
Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 18: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/18.jpg)
Hygroscopic setting expansion
Hydration------- ------ replaced as under water
Intermeshed and entangled--------------
Prevents further growth--------- -----------Growth is much free
(0.15%) (0.30%)
Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 19: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/19.jpg)
importance of setting expansion
Controlling setting expansion ↑ Spatulation ↑ SE ↓ W/P ↓ SE• Potassium sulphate (accelerator) — 4% solution ↓ setting
expansion from0.5% to 0.06%• Sodium chloride 2%(accelerator) and ground gypsum ↑
setting expansion.
Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 20: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/20.jpg)
PROPERTIES 1 Mixing water 37 – 50 ml/100g of powder
2 Required water 18.6 ml/100g of powder
3 Excess water 18 – 13 ml/100g of powder
4 Setting expansion range ±20%
5 Compressive strength 9.0 Mpa
6 Reproduction of details 75 ± 8 µm
7 Water / Ratio 0.50 ml/g
8 Spatulation 100 turns
![Page 21: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/21.jpg)
Factors Affecting Strength • Wet strength -Dental Plaster is 9 MPa . (free water) • Dry strength -is two or more times greater than
the wet strength.
• Excess water -there is no strength increase until the last 2% of free water is removed. (This strength increase on drying is reversible)
Craig’s Restorative dental materials -12th Edition
![Page 22: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/22.jpg)
• Temperature: Gypsum is stable only below about 40ºC at I00ºC or higher causes shrinkage and a reduction in strength.
• the strength increases with increased spatulation.
• Addition of accelerators and retarders : Lowers strength.
Craig’s Restorative dental materials -12th Edition
![Page 23: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/23.jpg)
MODEL PASTEREFFECT OF WATER/POWDER RATIO ON COMPRESSIVE
STRENGTH
W/P RATIO (ml/g) (↑)
COMPRESSIVE STRENGTH (Mpa) (↓)
0.45 12.5
0.50 11.0
0.55 9.0
![Page 24: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/24.jpg)
HEAT ACTIVATED RESIN MODELS
![Page 25: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/25.jpg)
(Poly-methyl methacrylate)(ADA No- 12)
HISTORY:Introduced to dentistry in
the year 1934
USES: Mainly used as denture
base Used in construction of
preclinical models
![Page 26: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/26.jpg)
COMPOSITION OF POLYMERPOWDER
• Ingredient Function
• Polymethyle metracrylate - main
• Benzoil peroxide - 0.5 – 1.5 –nitiator
• Dibutyle phthalate - 0.8 – 10% - External plasticizer
• Methacrylate or acrylate
monomer - Internal plasticizer
• Zinc or titanium oxide - opacifier.
• Mercuric sulfide - pigments and dies
• Glass fibres or beads - to increase stiffness
![Page 27: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/27.jpg)
COMPOSITION OF THE MONOMER LIQUID
Ingredient Function• Methyl methacrylate - Main chemical which polymerize
• Hydroqyinone 0.003 to 0.1% - Inhibits polymerization while storage• Dibutyl phthalate - Plasticizer.
• Glycol dimethacylate 1 – 2% - Cross – linking agent
Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 28: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/28.jpg)
PHYSICAL PROPERTIES (methyl methacrylate)
Melting point -48˚c
Boiling point 100.8˚c
Density 0.945 g/ mL at 20˚c
Heat of polymerization 12.9 Kcal/mol
*PHILLIPS science of dental materials,10th edition, pg-231
*PHILLIPS science of dental materials,10th edition, pg-231
![Page 29: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/29.jpg)
POLYMERIZATIONAddition polymerization
• Induction : The initiator benzoyl peroxide is activated
by heat to produce a free radical • Free radical – an atom that has unpaired
electrons
• Propagation: The free radical released combines with
other free radical to form double bond and release another free radical.Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 30: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/30.jpg)
Termination :
• Direct coupling ( exchange of energy)• Exchange of hydrogen atoms from one
growing chain to another.
Chain transfer :
• The active state is transferred from an activated radical to an inactive molecule.
• A new nucleus is created for new growthAnusavice Phillips Science Of Dental Materials 10th Edition
![Page 31: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/31.jpg)
FEW, WHICH WE MISSED YESTERDAY
• Pfaff, of Germany in 1756 – first to make the plaster cast (taking the bite)
• Vernon in 1936 – introduced acrylic resin • Before which-
Hard coconut shell Hippopotamus tuskOx femurTeak wood Gold, tin, porcelain, gutta-percha, vulcanite ( 1854)
Laney’s, Diagnosis and treatment in prosthodontics, 1st edition
![Page 32: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/32.jpg)
PROPERTIESPolymerization shrinkage (by volume) 6%
Polymerization shrinkage (linear) 0.2% to 0.5%
Coefficient of thermal expansion More than twice of that of composite (92.8)
Compressive strength 76MPa
Tensile strength 55MPa
Hardness (knoop) 15 – 18 km/mm2
Biocompatibility Good
Thermal conductivity Poor
Wear resistance Fair
Fatique resistance ( to flexing) Good
Impact resistance (to break when dropped)
Poor
![Page 33: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/33.jpg)
DIE
![Page 34: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/34.jpg)
Basic Requirements of Die Materials:
• Should have accuracy and dimensional stability.• Should have a smooth, hard surface which should not
easily abrade.• Should be compatible with impression material.• Should have high strength.• Should have good color contrast.• Economical.• Should be able to manipulate easily and fast.• Have ability to reproduce fine details & sharp margins• Resistance to abrasion
![Page 35: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/35.jpg)
Classification:• Hard die materials:
o Gypsum die materialsType IV gypsumType V gypsumDie Stone with Disinfectant (Steri-Die-A)Die Stone and Die Hardener Die Stone and Cyano-acrylate
o Resin based die materialso Electro plated dieso Gypsum-resin combination materialso Refractory die materials
• Flexible die materials:o Polyethero Polyvinyl siloxane
• Miscellaneous:o Silver amalgamo Silico-phosphate cemento Plastic steel
![Page 36: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/36.jpg)
Stone, High Strength (Type IV) (ADA;No: 35)
Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 37: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/37.jpg)
Formula CaSO4-(1/2)H2O
Powder Shape: Uniform
Density Dense ( compared to type II)
Production Steps Heat to 100C in 30%CaCl2 solution or MgCl2. ( 100 C water or autoclave 0.5% sodium succinate)
![Page 38: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/38.jpg)
COMPOSITIONα- hemihydrate Main composition
Potassium sulfate 2-3 % accelerator
Sodium citrate Retarder
Coloring agent 2%
![Page 39: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/39.jpg)
PROPERTIESWater: powder ratio 0.20 to 0.22 %Setting time Initial Final
7min9 min
Setting expansion24hr Setting Expansion
0.5 to 0.7%70%
Compressive strengthDry
34 Mpa80 Mpa
Dry hardness 92RHNDimensional changes
OcclusalCervical
0.06%0.00%
Tensile strength 8 Mpa
![Page 40: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/40.jpg)
• Advantages:• Greater abrasion resistance. • Have higher strength than stone or model
plaster.• Disinfection:• This can be achieved by disinfecting the
impression• By immersing the cast in disinfectant solution
like sodium hypochlorite• Incorporating disinfectant in the stone itself
![Page 41: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/41.jpg)
Conducted a study to find if gypsum cast as a potential source of microbial cross contamination
. He sterilized the alginate impression and dental stone with ethylene oxide and used serratia marcescens to contaminate the casts and incubated it in BHI(brain-heart infusion) medium for 24hr at 37˚c and then took pieces of the cast and incubated in agar plate for 7 days in 37˚c .
• concluded that gypsum cast is a potential source of cross contamination hence disinfection is necessary.
Ralph L. Leung et al (J Prosthet Dent 1983;49:210-211)
![Page 42: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/42.jpg)
Conducted a study on surface detail, compressive strength, and dimensional accuracy of gypsum casts after repeated immersion in hypochlorite solution
• He immersed 30 type III and type IV dental stone in slurry with 0.525% sodium hypochlorite solution and 30casts in slurry water.
• He concluded that there is a significant increase in linear dimension and significant decrease in wet compressive strength but both the solution produced loss of surface details.
Mohammed Aleem Abdullah et al (J Prosthet Dent 2006;95:462-468)
![Page 43: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/43.jpg)
Conducted a study to evaluate abrasion and compressive strength of gypsum casts after repeated
spray disinfectants
. He sprayed iodophor, acid glutraldehyde, phenol and water on type III and type IV dental stone
• . He concluded that there is a significant increase in abrasive resistance after repeated spraying of water or disinfectant.
• glutraldehyde decrease in compressive strength of type III stone by 26%,
• phenol increases the compressive strength of type IV stone by 18%,
• Iodophor had no significant effect on dental stone.Mitchell A. Stern et al : (J Prosthet Dent 1991;65:713-718)
![Page 44: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/44.jpg)
Conducted a Study of the physical properties of type IV gypsum, resin containing, and epoxy die materials
• He compared the properties of 3 new die materials and 2 conventional type IV gypsum products for linear dimensional change, detail reproduction, surface hardness, abrasion resistance, and transverse strength
• The result showed that gypsum products expanded, whereas the epoxy resin material contracted during setting. epoxy resin exhibited much better detail reproduction abrasion resistance, and transverse strength than the gypsum materials.
Philip Duke et al : (J Prosthet Dent 2000;83:466-473)
![Page 45: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/45.jpg)
Die Stone, High Strength, High Expansion (Type V)ADA No: 35
![Page 46: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/46.jpg)
PROPERTIES
Setting Expansion Max of 0.10% - 0.30%.W/P ratio 0.18 – 0.22Setting time 12±4min1hr compressive strength 7000psi.Mixing time 30sec to 1minWorking time 3 minTemperature alters the setting time
Above 50˚c retards setting timeAt 100˚c no reaction takes place
![Page 47: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/47.jpg)
• Advantages:• Increased strength & greater setting
expansion.• Compensates for casting shrinkage of base
metal alloys.
• Disadvantage:• High expansion
![Page 48: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/48.jpg)
Die stone with cyano-acrylate (to increase surface abrasive resistance)
• Conducted a study to evaluate the effectiveness of the cyano-acrylate on die stone. They investigated three products of die hardeners with regards to their influence on surface hardness of stone, film thickness and abrasion resistance.
• He concluded that cyano-acrylate resins as die hardeners effectively improve the surface hardness of the stone dies and that surface detail reproduction can be achieved by blowing the excess liquid applied with compressed air.
Habib H. Ghahremannezhad,et al: (J Prosthet Dent 1983;49:639-646)
![Page 49: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/49.jpg)
Die stone with disinfectant
• Conducted a study to evaluate the antimicrobial effect from incorporation of disinfectant into gypsum cast.
• He used four disinfectants and tested them against five microorganisms.
• concluded that sodium hypochlorite and neutral glutaraldehyde were effective in eliminating all growth of bacteria at 1 and 24 hrs.
• Idophore was effective in eliminating growth at 24hr but not at 1hr.
• Phenol did not have a profound antimicrobial effect at 1 or 24hr.
Steven. M. Mansifield et al :(Int. J. Prosthodontics 1991;4:180-185)
![Page 50: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/50.jpg)
Resin based die materials
• Resins are used as die materials to overcome the low abrasion resistance of die stone. Epoxy resins and polyurethane are the resin based die materials that are commonly used.
Craig’s Restorative dental materials -12th Edition
![Page 51: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/51.jpg)
EPOXY RESINS
• Is compatible with most impression materials• Exhibited better detail reproduction• Abrasion resistance• High Transverse strength than gypsum-
materials.
![Page 52: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/52.jpg)
PROPERTIES
Working time 15minSetting time 1-12hrsCompressive strength: Initial After 7 days
9500 psi16,000psi
Polymerization shrinkage 0.1-0.2%.Hardness 83RHNDimentional changes. Occlusal Cervical
0 – 0.15%
0.19%
Detail reproduction 25µmKHN 17.76 – 29.80
![Page 53: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/53.jpg)
Advantages: • 1. Superior abrasion resistance.• 2. Less brittle. Disadvantage:• 1. Shrinkage on polymerization.• 2. Less dimensional stability.• 3. Expensive.• 4. More viscous than stone, so more prone to
trap air in preparation
![Page 54: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/54.jpg)
Compared three epoxy die material (Pri-Die , unitek epoxy die and epoxydent) for marginal adaptation, fit and retention in 60 Complete crown and MOD inlay
• He concluded that there is no significant difference between the materials but pri-die and epoxydent dies had more clinical acceptance for MOD and
• unitec die material acceptable for complete crown.
P. Yaman, et al: (J Prosthet Dent 1986;55:328-331)
![Page 55: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/55.jpg)
He studied the Dimensional accuracy of an epoxy resin die material using two setting
Methods• He retarded setting
reaction and checked the dimensional accuracy, he manipulated high-strength high-expansion gypsum (Die Keen); and a resin-filled gypsum (Resin Rock) as per manufacture instruction and then manipulated to retarded polymerization set.
• He concluded that Retarding the setting reaction of an epoxy resin die material improved its accuracy.
Jacinthe M. Paquette, et al : (J Prosthet Dent 2000;83:301-305)
![Page 56: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/56.jpg)
He studied three commercially available resin die systems and
evaluated some characteristics that relate to their clinical performance.
• Characteristics evaluated include accuracy of fit, detail registration, and Knoop hardness.( epoxydent, precision, velmix and die stone).
• Out of the 80 die evaluated only one did not fit that is gypsum. Epoxy group were harder and had no significant difference in accuracy.
Gerald T. Nomura,et al : (J Prosthet Dent 1980;44:45-50)
![Page 57: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/57.jpg)
He compared the pertinent properties of die materials used for the indirect materials has been made
• Eight classes of materials were evaluated and the result showed that stones were superior from other materials in stand point of dimensional accuracy but it lacked abrasion resistance.
• The dies made from the ceramic material, silicophosphate cement, one of the resins and by electrodeposition were superior in abrasion resistance
• The surface of the electroplated dies, the ceramic material, stones and silicophosphate cement provided excellent duplication of detail.
Svicrker toreskog et al (J Prosthet Dent 1966;16 :119-131)
![Page 58: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/58.jpg)
He studied Accuracy of stone, epoxy and silver plate-acrylic models for selected dimensions of stone
• Epoxy resin and silver plate backed with acrylic resin models were compared to each other and their master model which simulated the abutments for a FPD and
• concluded that Silver plated models backed with acrylic resin were not as accurate as stone or epoxy resin models, between which there was no significant difference.
Stevens L, Spratley MH et al : (J Dent mater 1987;3:52-55)
![Page 59: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/59.jpg)
ELECTROFORMED DIES
![Page 60: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/60.jpg)
Types of electroformed dies
• Silver plated • Copper plated
![Page 61: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/61.jpg)
SILVER FORMED DIE
• Polysulphide and silicone impression materials can be silver plated (Cathode)
![Page 62: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/62.jpg)
Composition of electroplating bath solution
• Silver cyamde-36 gm• Potassium cyanide-60 gm• Potassium carbonate-45 gm• Water(distilled)-1000ml
• Electroplated for 10hrs, using 5-10mA/cm2 of cathode surface
![Page 63: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/63.jpg)
COPPER FORMED DIES
• Composition of electroplating bath solution
• copper sulphate• alcohol or phenol• Sulphuric acid• phenol sulphonic acid
• About 15mA current proceed for 12 to 15 hours
![Page 64: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/64.jpg)
• Advantages :• Moderately high strength • Adequate hardness• Excellent abrasion resistance.
• Disadvantages:• silver cyanide and acid to the solution
produces hydrogen cyanide,
![Page 65: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/65.jpg)
He compared silver-plated and stone dies from rubber-base impressions
• Studied The accuracy of silver-plated dies as compared with that of stone dies was investigated using a silicone impression material, Xantopren, and a polysulfide material, Permlastic.
• Concluded that Primary stone dies from Xantopren impressions are more accurate than primary or backup silver-plated dies from Xantopren impressions.
• There is no significant difference in accuracy between primary stone dies and primary silver-plated dies from Permlastic impressions.
• Secondary silver-plated dies are less accurate than primary stone dies or primary silver-plated dies from Permlastic impressions.
Joseph P. Cooney et al :(J Prosthet Dent 1974;32:262-266)
![Page 66: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/66.jpg)
FLEXIBLE DIES
![Page 67: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/67.jpg)
TYPES OF FLEXIBLE DIES
• POLYETHER
• POLYVINYL SILOXANE
![Page 68: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/68.jpg)
POLYETHER
• The polyethers (synonym: epimine) cure through cross-linking .
• The reaction involves ring opening without formation of volatile byproducts.
• Polyeter is a stiff material so thinner is used to reduce the stiffness
J Prosthet Dent 1992;68:372-374
![Page 69: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/69.jpg)
Composition
Base paste• Polyether polyme• Colloidal silica as a filler • Glycoether or phthalate as plasticizer Accelerator paste• Alkyl-aromatic sulfonate• Colloidal silica as a filler • Glycoether or phthalate as plasticizer
J Prosthet Dent 1992;68:372-374
![Page 70: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/70.jpg)
Advantages:• More rapid setting• Ease of removal • Does not adhere to the acrylic resin
Disadvantages:• Expensive• Hyper sensitivity to polyether catalyst system
leading to contact dermatitis
J Prosthet Dent 1992;68:372-374
![Page 71: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/71.jpg)
Polyvinyl siloxane( Addition silicone)
• It was introduced in 1970s • It has much greater dimensional stability.• It’s less rigid than polyether.• They have excellent dimensional accuracy and
long term stability.
J Prosthet Dent 1992;68:372-374
![Page 72: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/72.jpg)
Composition Accelerator paste
• Divinyl siloxane• Other siloxane prepolymers• Platinum salt (chloroplatinic acid) catalyst• Palladium - hydrogen absorber• Fillers
J Prosthet Dent 1992;68:372-374
![Page 73: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/73.jpg)
Composition Base paste
• Poly methyl hydrogen siloxane• Other siloxane polymers• Fillers
J Prosthet Dent 1992;68:372-374
![Page 74: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/74.jpg)
Working time 1-4 minSetting time 3-5min
J Prosthet Dent 1992;68:372-374
![Page 75: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/75.jpg)
Conducted a study to compare the surface detail reproduction of 7 potential flexible die materials
• Concluded that surface detail reproduction of the flexible dies has no significant difference from normal stone die but among the flexible die IMPREGUM-F die material reproduce details better.
• He also said that polyvinyl siloxane impression material is incompatible with polyvinyl siloxane die material without die seperators.
Jack.D.Gerrow et al : (J Prosthet Dent 1998;80:485-489)
![Page 76: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/76.jpg)
REFRACTORY DIES
![Page 77: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/77.jpg)
Requirements
• Easy manipulation• Stability at higher temperature• It should produce mould expansion to
compensate for casting shrinkage of alloy• It should produce a smooth surface on setting• It should be porous to allow air from the mould
space to escape.• It should have adequate strength to withstand
casting pressure.
![Page 78: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/78.jpg)
Types of refractory dies
• Gypsum bonded die-vestment • Phosphate bonded die-vestment ( for all
ceramic)• Ethyl silicate-bonded
Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 79: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/79.jpg)
Gypsum bonded die-vestment
• Brodsky in 1933 • Composition • 70% mullite• 30% plaster of Paris• Phillips, suggesting that gypsum-bonded investments
should not be heated above 700 C ̊ as decomposition of the gypsum occurs, producing sulfur trioxide.
• Modifiers, such as boric acid, added to reduce the contraction
Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 80: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/80.jpg)
Setting expansion of divestment
0.9%
Thermal Expansion 0.6%
Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 81: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/81.jpg)
Phosphate bonded die-vestment
• Moore and Watts in 1949 developed phosphate- bonded material
Anusavice Phillips Science Of Dental Materials 10th Edition
![Page 82: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/82.jpg)
Gypsum – resin combination materials
• Resin rock die material : epoxy resin + high expansion stone
• Advantages of both.
• Dimensional shrinkage is compensated with the expansion of the gypsum stone.
![Page 83: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/83.jpg)
Plastic steel: (Victor.E.Wasser)
• A material used in industry for making molds, models, and dies has been found to be useful for making dies and casts for splints and other restorations.
![Page 84: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/84.jpg)
PROPERTIESUltimate compressive strength 16,000 p.s.i.Tensile strength 8,000 p.s.i.Flexure strength 11,000 p.s.i.Relative impact strength O.8 Foot-pounds per inch of
Notch IZODRockwell hardness F- 93Resistance to heat 300˚F.Dielectric constant 2.9Machining qualities PoorSpecific volume 15-16 cubic inches per poundShrinkage on 4 by 3 by 1 casting
0.00016 inch per inch
![Page 85: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/85.jpg)
DISADVANTAGES
• Its color is black. • The material is more difficult to mix than die
stone.• It is necessary to use a separating medium
before the master cast is poured.• A separating medium is necessary if the wax
patterns are to be formed.
![Page 86: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/86.jpg)
Other die materials
• Silver amalgam• Silico-Phosphate cement• Silica modified epoxy resin• Bismuth alloy
![Page 87: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/87.jpg)
SELECTION OF DIE MATERIALSMATERIAL RECOMMENDED
USEPRECAUTION
Type IV & V dental stone
Most situations •Proportionate mix•Vacuum mix•Surface Hardeners
Epoxy resin All ceramics •Incompatible with poly sulfides & hydrocolloids•Spacer (shrinkage)
Electro plated dies
All ceramic crowns •Cyanide usage(toxic)•Incompatible with hydrocolloids, polyether & polysulfides(Ag plating)
Flexible die materials
Provisional compatibility indirect compsite material inlay/ onlay material
•Check for between die and impression especially elastomers)
![Page 88: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/88.jpg)
Compatibility with impression materials
Dental stone •Impression compound•Alginate•Zinc oxide euginol•Agar-agar•Rubber base material
Electro plated (copper) •Rubber base materialElectro plated ( silver) •Polysulphide
•Polyether•Addition silicone
Polymer epoxy •Rubber base materialResin •Polyether
•Addition silicone•Polysulphide
![Page 89: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/89.jpg)
FUTURE MODEL AND DIES
![Page 90: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/90.jpg)
Types of optical impression and model technology
• CEREC• The E4D (D4D TECH)• DCS PRECIDENT SYSTEM• iTero • LAVA• Haptic technology
![Page 91: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/91.jpg)
Potential benefits• Saves time and one visit for in-office systems• Opportunity to view occlusion• Accurate restorations created on digital models • Potential for cost-sharing of machines.• Accurate, wear- and chip-resistant physical CAD/CAM
derived models.• No layering/baking errors.• No casting/soldering errors.• Cost-effective.• Cross-infection control.
![Page 92: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/92.jpg)
![Page 93: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/93.jpg)
CEREC
• The first system introduced was the CEREC 1 in 1986.
• The CEREC 1, 2 (1994) and 3 (2000) systems (Sirona Dental) have all used a still camera to take multiple pictures that are stitched together with software.
![Page 94: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/94.jpg)
• Parsell DE et al(2000)• study found that the average camera
angulation error by clinicians was just under two degrees, insufficient to introduce error as the camera was tolerant of errors up to five degrees in buccolingual and mesiodistal planes
Parsell DE et al:(J Prosthet Dent 2000;83:301-305)
![Page 95: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/95.jpg)
E4D (D4D TECH)
• Takes several images, using a red light laser to reflect off of the tooth structure
• Requires the use of powder in some limited circumstances.
![Page 96: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/96.jpg)
DCS PRECIDENT SYSTEM
• Designed for metal copings for PFM & FPDs.
• Conventional wax up required.
• Touch probe• 7 –unit bridge on one
side.• Acceptable marginal
accuracy.
![Page 97: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/97.jpg)
Compare the marginal accuracy and refinement time of titanium copings fabricated by 3 different CAD/CAM
systems relative to standard casting techniques
• Concludes that manual adjustment significantly improves the marginal accuracy of CAD/CAM system-fabricated titanium copings.
• The highest marginal accuracy was achieved with the DCS system, using a longer refinement time.
Siegbert Witkowski et al :(J Prosthet Dent 2006;96:47-52.)
![Page 98: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/98.jpg)
iTero
• The iTero system uses a camera that takes several views (stills), and uses a strobe effect as well as a small probe that touches the tooth to give an optimal focal length.
• NO use of powder
![Page 99: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/99.jpg)
LAVA
• Chairside Oral Scanner (LAVA COS, 3M ESPE) takes acompletely different approach using a continuous video stream of the teeth.
![Page 100: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/100.jpg)
Compare the fit of all-ceramic crowns fabricated from LAVA intraoral digital impressions with the fit of all-
ceramic crowns fabricated from silicone impressions
• 1. Crowns from intraoral scans revealed significantly better marginal fit than crowns from silicone impressions.
• 2. Marginal discrepancies in both groups were within the limits of clinical acceptability.
• 3. Crowns from intraoral scans tended to show better interproximal contact area quality.
• 4. Crowns from both groups performed equally well with regard to occlusion
Andreas Syrek et al :( J prosthet dent 2010;38;553-559)
![Page 101: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/101.jpg)
Haptic technology
This is a virtual waxup system whereby the technician can sit in front of a computer screen looking at a 3D model, and holding a computerized wax spatula (actually an elaborate computer mouse)
![Page 102: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/102.jpg)
![Page 103: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/103.jpg)
INITIAL SCANNING
ANGULATION
DIGITAL MODEL
![Page 104: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/104.jpg)
![Page 105: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/105.jpg)
REFERENCES
• Craig’s Restorative dental materials -12th Edition• Anusavice Phillips Science Of Dental Materials 10th
Edition• Rosenstiel, Contemporary Fixed Prosthodontics –
4th Edition• William J. O’ Brien: Dental materials and their
selection, 2nd edition.• Properties of die materials: A comparative study (J
Prosthet Dent 1966;16 :119-131)
![Page 106: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/106.jpg)
• A comparison of silver-plated and stone dies from rubber-base impression
(J Prosthet Dent 1974;32:262-266)• An investigation of epoxy resin dies (J Prosthet Dent 1980;44:45-50) • Effect of cyano-acrylate on die stone
(J Prosthet Dent 1983;49:639-646)• Gypsum cast as a potential source of microbial
cross-contamination (J Prosthet Dent 1983;49:210-211)
![Page 107: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/107.jpg)
• Comparison of three epoxy die materials (J Prosthet Dent 1986;55:328-331)
• Accuracy of stone, epoxy and silver plate-acrylic models (J Dent mater 1987;3:52-55)
• An evaluation of dental stones after repeated exposure to spray disinfectants. Part I: abrasion and compressive strength
(J Prosthet Dent 1991;65:713-718)• Antimicrobial effect from incorporation of
disinfectants into gypsum casts (Int. J. Prosthodontics 1991;4:180-185)
![Page 108: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/108.jpg)
• Flexible casts used in making indirect interim restoration (J Prosthet Dent 1992;68:372-374)
• Comparison of the surface details reproduction of flexible die material system (J Prosthet Dent 1998;80:485-489)
• Study of the physical properties of type IV gypsum, resin-containing, and epoxy die material (J Prosthet Dent 2000;83:466-473)
• Dimentional accuracy of an epoxy resin die material using two setting methods
(J Prosthet Dent 2000;83:301-305)
![Page 109: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/109.jpg)
• Surface detail, compressive strength, and dimen sional accuracy of gypsum cast after repeated immersion in hypochlorite solution (J Prosthet Dent 2006;95:462-468)
• Marginal accuracy of titanium copings fabricated by casting and CAD/CAM techniques (J Prosthet Dent 2006;96:47-52.)
• Clinical evaluation of all-ceramic crowns fabricated from intraoral digital impressions based on the principle of active wave front sampling ( J prosthet dent 2010;38;553-559)
![Page 110: Model and die materials](https://reader036.vdocuments.us/reader036/viewer/2022062401/587cc24e1a28abfa018b482f/html5/thumbnails/110.jpg)