- Site Name : iPECS Site Name- Device Name : System Name- Model Name : iPECS-MG300- IP Address : 10.10.10.1- Date : 2014.05.22- Time : 10:56:28Welcome to iPECS-MG system. Press enter.Your address is 10.10.10.5 Your TCP port number is 1.IPKTS System, Remote Maintenance AccessENTER PASSWORD: *You are accepted!Now, follows normal process!iPECS-MG MPB300 SystemVersion iPECS-MG/GS56M-2.0Ci JUN/12Checksum: 0Dsp Version: 1.1(10/03/16),(A-law)DATE: 01/01/09TIME: 04:24:02SITE NAME: You are on TCP01ENTER PASSWORD: ******maint> ?Maintenance Command List: ds ## - View Device Status dc - Display Device Configuration Table ta - Traffic Analysis ws - WTIB Statistics Information ts show|[slot #] - Time Slot Information ts check [slot #] - Time Slot Switching Information system meminfo|devinfo|mtdinfo - System Resource Display ns hi|hm|hg|hf|hd ddd.ddd.ddd.ddd - Networking Resources Setting nr - Display Networking Resources reset 0|all|devs|[slot #] - Reset Command log view raw|dump|last - View the Reset Information log clear - Clean the Reset Information slog view|clear - View/Clear the System Log Information gw log - Check Current GW Log Information dir c|d|e - Display directory entries ren c|d|e file-1 file-2 - Rename file del c|d|e file - Delete file vlan reset|set priority vlan-id - Vlan set priority,id dhcp on|off - MPB Dhcp Set ON/OFF ver - Display SW version info. ksu - Check the KSU Status. mp led|power|act2|time - Check Device for mass production. usb down - Download DB to USB. x - Exit Maintenance ? - Help Menumaint> xDATE: 01/01/09 TIME: 04:24:08Exiting maintanence utility...iPECS-MG MPB300 SystemVersion iPECS-MG/GS56M-2.0Ci JUN/12Checksum: 0Dsp Version: 1.1(10/03/16),(A-law)DATE: 01/01/09TIME: 04:24:08SITE NAME: You are on TCP01ENTER PASSWORD: ******mon> ?Monitor Command List: t {[s|c|m]xxx} - Set Device Trace tm xxx - Set Trace ID Mask tg [mode] .. - Set Trace ID Mask l xxxx - Get MDN_ID of DN cim - Show cim information cm - Show CM general information cluster - Show Cluster information fd - Show fd information ipcr - Show IPCR information lcminfo - Show lcm information mem - Show memory allocation information ppe - Show ppe information sip mem - Show SIP memeory allocation information sip stack - Show SIP stack allocation resource info sip sipmcall - Show SIPM allocation resource info term com|stn|trk|mdn|vpcm - Show term information rtp - Show rtp information ver - Show Software Version vms - Show vms information atd_info - Show ATD information loc2lsi all|loc#(0-1023) - Show LCM Site Index from Location number index2lsi all|index in decimal - Show LCM Site Index from id.index(dec) x - Exit Monitor ? - Help Menumon> tm callenable all call message tracemon> t s 100Show current trace setting for unit_id & slot_no * Trace all port is enabled UNIT_ID- STN:100 Slot Nodone.mon> xDATE: 01/01/09 TIME: 04:24:25Exiting monitor utility...04:24:27(24) [STN:100MDN:100] MDN_MSG_SEIZE_REQ [P1:0000, P2:0000]0001307 [STN:100] STN_STATE_WAIT_MDNSEIZERSP