metnet international scientific conference and workshop 2014/metnet_2014.pdfmetnet international...
TRANSCRIPT
BEARING CAPACITY OF COMPRESSIONAL NOTCHED C-PROFILE MEMBERS
Nazmeeva T.
Scientific adviser _ Vatin N.I.
St. Petersburg State Polytechnic University
METNET International Scientific Conference and Workshop SPb-2014
St. Petersburg State Polytechnic University
HAMK University of Applied Sciences
LIGHT STEEL THIN-WALLED STRUCTURES Low weight of the load-bearing steel framework (between 20 - 25 kg/m2), short payback period and high energy efficiency of buildings made of cold-formed thin-walled members are the facts which make them in great demand for housing as well as for construction of industrial and public building
BUILDINGS' RECONSTRUCTION
before
after
Light steel thin-walled structures are able to solve main problems of buildings' reconstruction: to lower foundation and walls loads, to carry out construction works in restrained urban conditions without use of heavy equipment and without shutdown of the process inside the building
STRUCTURAL ELEMENT - PANEL separate elements of the framework are joined in one panel with the help of guide casings
and sheets
- the structures based on cold-bent steel galvanized thin-walled C-profiles with the thickness up to 3 mm.
cold-bent C-profile is used for interior panel
cold-bent notched C-profile is used in exterior panel
to find ultimate bearing capacity and to study stress-strain behavior of compressional cold-bent notched C-profile members of different cross-sections area as well as comparison study of their work and that of cold-formed solid section C-profile members
Purpose of research
Objective of research
- analyze areas of cold-bent profile in construction
- theoretical investigations on global buckling and bearing capacity of
members of C-shaped notched profiles
- experimental investigations on global buckling and bearing capacity of
members of C-shaped notched profiles
- to find and estimate factors influencing bearing capacity
- numerical simulation of members of C-shaped notched profiles
- methodology
Subject of research
2200
h
2200
h
a-a
h
b-b
h
Ï ÑTÑ
c=15
c=15
h
b =41
b =37
f1
itr =3tr = 4
etr = 5
itr
tretr
t
h
itr
tretr
itr
tr
etr
itrtr
etr
t
it
t
et
itrtr
etr
itrtr
etr
f l
f l
b =47f2
1
2
b =31
ñ fl
r =3r = 4
r = 5
t
75 25 25 2525
1111
1111
1111
1111
1111
1111
A
A
Cold-formed steel notched C-shaped profile
Problems
But in Russian national standards there is no clear systematization of thin-walled members’ calculations
THEORETICAL ESTIMATION OF THE CROSS-SECTION
Z1 Z2b =21,5
h =4
6,28
37e1
ñ =1
3ñ
=13
b =18,5 b =18,5e1
e1
43
e2 b =21,5e2
e1
e1h
=46,
28e1
Î
Z1 Z2
Y2Y1
ez2=3,9
ey2=
0,56
hp=1
46
53.4
4
Y2
Y1
Z2
z2
e1e2
Î 1
Î 2
e1e1
hð=14
6
ñ =
13
y2
ñ =
13h
=29,
2
e =3,2
hp/
2=73 h
=43,
8
Zm
ax =
77,4
Ymax =32,6
e
=5,
6
b =21,5
43
e2 b =21,5e2
Z1
37
e1b =18,5 b =18,5e1
W
BMM
F
P
y
y
x
х WW
THEORETICAL ESTIMATION OF TEST MEMBERS’
THEORETICAL ESTIMATION OF TEST MEMBERS’ Thus, strength condition is considered to be provided if the reinforcing force caused by environmental loads does not exceed the breaking stress the element can bear.
Nc,e ≤ Nuc,e
Where Nc,e is the stress in a compressed thin-walled element from the intended loads; Nuc,e is the breaking stress, which the compressed thin-walled element can bear (minimal bearing capacity of the thin-walled element cross section).
Nuc,e = А Ry φnt
Nuc,e is a breaking stress, kN; А is the cross-sectional area, cm2; Ry is design strength of steel that equals the yield point, MPa; φnt is the empirical constant, that takes into account profile type, Nc,e is stress in the element as a result of statistical calculation, kN.
TESTING COMPLEX B50 (2500mm/50t)
TESTING COMPLEX С12 (1200mm/20t)
During the tests objects are under the loads which are equal or higher than those in actual conditions. Main advance of carrying out tests at the testing bed is possibility to estimate the object's response to specific conditions (load limits, definite type and load value), all other things constant. This helps to find out latent defects or reserve of structure bearing capacity.
Testing bed is usually a rigid frame which the model is bearing on.
THE SCHEME OF STRAIN-GAUGES’ INSTALLATION ALONG THE CROSS-SECTION OF NOTCHED C-SHAPED PROFILE
12 16
13
1415
11 17
B
51
4
32
721
A
3
17 11
6
7
9
1018
19 2220
218
1 2 4 5
1416 15 13 12
B
A
23 24
THE SCHEME OF STRAIN-GAUGES’ INSTALLATION ALONG THE CROSS-SECTION OF NOTCHED C-SHAPED PROFILE
TEST RESULTS – С-shaped notched profile – ТС-150-2,0
TEST RESULTS – С-shaped profile – ПС-150-2,0
TEST RESULTS – С-shaped profile
ПС-150-2,0 ТС-150-2,0
TEST RESULTS
Comparison study of bending curves for the members with cross-sectional height of 150 mm
TEST RESULTS
Load-deformation curves for long members-tests (2.2 m) with thickness = 2.0 mm
TEST RESULTS - Stress diagram
36.527.7520.8
60.55
45.5
23.9 40.85
48.4
55.95
61.1544.531.8
87.35
67.2
47.35 70.1
77.8
85.5
132.882.340.7
124.6
95.5
66.8 134.25
134.35
135.35
205.0
148.6
93.0 170.0
173.15
182.35
24.0
59.9 109.5
167.790.130.95 58.2 131.9
37.7 53.5
32.5
89.2154.7
125.8245.7
20 kN
30 kN
50 kN
62.5 kN
81.297.1
57.5
62.0
46.0178.3
40.4
33.5
25.5
201.1
168.7
120.5
100.9
110.2
103.1
95.3
60.9
106.2
144.4
187.3
116.627.7 105.4 183.075.615.4 164.9
38.0 22.3 32.0 74.847.219.8 49.7
16.8 4.219.417.6 9.518.0 14.3
-
96.8
70.7
106.5
898
+
174.4
88.4
85.4
464.4
40 kN
50 kN
20 kN
ПС-150-2,0 ТС-150-2,0
NUMERICAL SIMULATION PLM Femap 10.1 Nastran
Nastran’s triangle and fore-cornered fracture finite elements of plate type were used to create finite-element model of the whole member. Fine grid at the places of bending was made manually.
NUMERICAL SIMULATION PLM Femap 10.1 Nastran
This calculation was carried out to see postbuckling behavior of the member. And its results were almost completely the same as those of experimental investigation.
EXPERIMENTAL INVESTIGATION NUMERICAL SIMULATION
NUMERICAL SIMULATION PLM Femap 10.1 Nastran
CONCLUSIONS 1. Members in a frame building panel undergo eccentric compression with biaxial eccentricity. 2. The critical factor for them is flexure-torsion global buckling. 3. The yield strength point overrunning is considered bearing capacity exhaustion factor, and the structure undergone this should be considered unusable. 4. Bearing capacity value is influenced by value of eccentricity that increases bimoment, effective area, and some initial imperfections. 5. Factors’ impact on the cold-bent notched C-profile members’ work is suggested to take into account with the help of φnt coefficient 6. The experimental work proved relevance of theoretical background and conclusions. 7. It is found that notches’ presence in the walls of profile influences the stress-strain behavior of eccentrically compressed members. Profile wall buckling increases as the wall is weaken by notches, as the result eccentricity increases, and cross-sectional stress becomes 20-25 % higher. Difference of received empirical constant was 5 – 7 %.
THANK YOU