SYED IMRAN SHAH Al-Jubail, Saudia Arabia:|Phone: +966597565905 |Email: syedimran_136@yahoo.com

Piping QC Engineer

Career Objective:

To be a part of an organization where I can fully utilize my skills and make a significant contribution to the success of the employer and at the same time my individual growth.

Work Experience:

Experience in Static equipment

Responsibilities:

Preparation /Review of Material Requisitions, specification, document number, issue date and revision index etc

Technical and quality requirements, particularly applicable inspection and test requirements

Plan, organize and perform Pre-Inspection Meetings (PIM) Compile and submit Inspection Assignment Packages (IAP) Review and approve Vendors Inspection and Test Plans (ITP), in liaison with SAIR (VID)

representative Plan and coordinate Vendor Inspections

Job Responsibilities:

Preparation of Inspection and Test Plan, checklist, procedures and review of construction drawing.

Material Receiving inspection of all RTRP/FRP Pipes and fittings, Gasket, valves, flanges, bolts & nuts in compliance to material list, mill certificates, test reports and correct material specification.

Experience in Static equipment

Job designation: Planning CoordinatorCompany name: Jubail chevron Phillips (JCP), Saudi Chevron Phillips

(SCP)Project: Turn Around 2015

Job Title: Procurement QC CoordinatorPeriod: December 2015 – Still ContinueCompany: Saudi Kad

Control of quality for piping fabrication such as fit-up, visual and dimensional inspection conforming to approved for construction drawings.

Responsible for issuance of Non – Conformance Report if any violation and out of standard for piping works.

Conducts quality co-ordination meeting and initiate corrective and preventive action. Inspection of UG RTR piping spools fabrication, installation and testing. Assign as hydro test engineer for all piping and thermoplastic piping, shop fabrication. Line flushing, air blowing; pressure testing, piping lay-up inspection, relief valve installation, re-

instatement and final inspection for mechanical completion. Responsible for inspection of pipe spools for shop and fabrication such as fit-up, dimensional

and visual inspection Prepare Request for Inspection(RFI) to Project Management Team(PMT) and Project Inspection

Division through Quality Management Information system(QMIS) Witnessed, checked, monitor and inspect of hydro test pressure as per SAES-004(General

Requirements for Pressure Testing) Prepare Non- Conformance Report (NCR), Preventive Action Request (PAR) and initiate

corrective Action for every violation and out of Standard of Construction activities. Close log book entry or surveillance violation. Assigned as QC-Piping Inspector for Fiber Glass Reinforced Plastic Piping (FRP) of installation

and spool fabrication for 24” Fire water line and 72” cooling water line-Adhesive bonded joint and Lamination joints.

Witnessed and inspection of FRP piping system for Adhesive bonded joints, Lamination joint, Barcol hardness as per ASTM D 2583.

Maintaining the storage conditioning of all fiber glass woven roving 270,360,580 g Adhesive kits, chemicals such as Epoxy resin, Hardener, vinyl Ester Resin etc.

Collecting daily work updates (about column, Drums, Pressure vessel, Exchanger, fin fan heat exchanger) from site and submitting to Senior Planner.

Stacking the valves & PRD’S as per standard and delivering to the relevant workshops To Identify PRD’S and Control valves on Isometric and P&ID’S for removing. Supervision of fabrication & erection of equipments and piping Assure the work is carried out as per P & ID’s, layouts drawings & isometrics Selecting Crane or fork lift or telehandler or Boom Truck as required for lifting by calculations

& correct estimation, depends on load and shape Reviewing stamped and finalized drawings (including piping plans and sections, piping

isometrics, piping supports, tank and vessel layouts and details, etc.) Supervising during loading and unloading the PRD’S, Control Valves by Crane & Fork lift. Receiving Valves from the workshop and delivering to the site area. Reviewing and monitoring all material deliverables from materials store. Responsible of Bolt Torquing & Tensioning of flanged joints Manage all the spare parts

Job Title: Piping SupervisorPeriod: Nov 2014 – May 2015Company: Shah Construction Company Pvt. Ltd

Job Responsibilities:

To study the isometric drawing received from the clients and to identify the pipelines carry out the inspection works.

Check flow direction arrows on valves verify that they are properly identified and valves are installed in accordance with flow direction.

Ensure that pipe supports, hangers and guides have been installed in accordance with the piping drawings and the pipe support details.

Supervise and Inspection of cold and hot insulation, cladding on piping and equipment. Conduct safety walk through in the site in co-ordination with the safety department on weekly basis.

Job Title: Internee Engineer ( University internship )Period: June 2013 – August 2013, July 2014- Oct 2014Company: Heavy Mechanical Complex Pakistan (Manufacturing Company)

Major Duties and Responsibilities

Maintained and updated structural drawing register for every project having details on issued sketches and drawings.

Ensured correctness of exclusive drawings, sketches and referred documents. Provided drawings and sketches only after sanction. Prepared drafts for structural design drawings. Ensured all drawings comprise of required design details. Created barge anchor design arrangements in compliance with guidelines from company Collected existing equipment measurements and other necessary data essential for preparing drawings.

Internee Mechanical Engineer:

Supervising After Casting and forging, heavy weight products (Gears, Shaft etc.) replace to machine shop by Gantry crane

Supervising during product manufacturing in machine shop, Checking of all production like different material for different companies.

Loading and unloading heavy products by Gantry Crane or by fork lifter Supervising during the fabrication, NDT (UT, MT, PT) and impact, tensile, compressive, Hardness

(Rockwell, Brinell, Vicker) tests Machining projects.

Job Title: Mechanical QC EngineerPeriod: Nov 2014 – May 2015Company: Gulfababeel

Job Title: Internee Mechanical Engineer Period: June 2012 – August 2012, June 2013 – August 2013, July 2014- Oct 2014Company: Heavy Mechanical Complex Pakistan (Manufacturing Company)

Job Title: Interne Field Engineer (For University Final Year Project)Period: Sep 2013 – June 2014Company: Pakistan Petroleum Limited (PPL), Mandra Field, Pakistan (Oil & Gas Sector)Project: Adhi (21-22) RIG (Achievement of Well Trajectory by using Directional Drilling Techniques)

Responsibilities:

APR: (Authorized Permit Receiver )

• Identifies the work that is to be completed• Ensures that all potentially hazardous work is controlled and properly authorized;• Ensures that all hazards associated with the work have been identified• Ensures that all necessary safety procedures for controlling the risks are properly implemented while the work is being completed; and,• Ensures that the worksite is left in a safe condition when the work is completed or suspended.

Studies topics

• Design and Simulation of BHA and Well Circulation System on Pro-E• Well Control and Circulation System• Directional Well Planning• Directional Drilling Equipment (BHA)• Measurement While Drilling (MWD) • Analysis of Drilling Problems at Rig site • Well-Bore Survey Calculations Methods.

Work as Design Engineer as a Freelancer

Semester Projects:

• Design & Analysis of Armored Vehicle-Launched Bridge in a group project, I was a group leader as well.

• Wind Turbine Design (wind assessment and designing of a wind turbine) for F-9 Park Islamabad Pakistan in a group project, I was a group leader as well.

• Thesis on Boiler Design in a group project, I was a group leader as well.• Energy Auditing of my Home.• PV Sizing (Photovoltaic) of Home• UPS System Design of my Home

Job Title: Interne Field Engineer (For University Final Year Project)Period: Sep 2013 – June 2014Company: Pakistan Petroleum Limited (PPL), Mandra Field, Pakistan (Oil & Gas Sector)Project: Adhi (21-22) RIG (Achievement of Well Trajectory by using Directional Drilling

Techniques)

Computer Skills:

Engineering Application Software: • Primavera 6.0• Pro-Engineer Wildfire 4.0-5.0,• AutoCAD• Abacus• Sankey Tool

Miscellaneous:Excellent computer using and internet searching Skill, MS Office, Windows

XP/98, Windows 7, and Windows 8. Many more

Personnel Skills:

• Leadership• Excellent communication and interpersonal skills.• Ability to solve problems• Excellent leadership qualities and keenly interested to work in a team. • Self-motivated, Persistent, Creative, Dedicated, and Adaptable.

Educational Background:

B.Sc Mechanical Engineering: University of Engineering &Technology (UET) Taxila Pakistan GPA: 3.32/4.00 F.Sc Pre-Engineering:Government Science College Multan Punjab Pakistan High 1st Division Matriculation:Government Pilot High School Multan Punjab Pakistan High 1stDivision

Hobbies &Healthy Activities

• Badminton • Athletic Sports• Rugby• Spending time with friends

Personal Profile

• Father’s Name: Muhammad Saleem Shah • Marital Status: Single• Date of Birth: 1st February, 1993• Nationality: Pakistani• Passport No: WZ5145691• Date of Expiry(Passport) 9th March, 2019• Iqama No. 2393893975• Phone: +966597565905 • Email: syedimran_136@yahoo.com