man2512 zonesense plus en add ons inst comm

8/9/2019 MAN2512 ZoneSense Plus en Add Ons Inst Comm

1/28

MAN 2512 Rev: October 2005

ZoneSense

FI RE

ZONE 1

ZON E2

ZONE3

ZONE 4

ZO NE 5

ZONE 6

ZONE 7

ZONE 8

FAULT/ DISABLED/TEST

CANC EL

MENUIEN TER

SYSTEM STATUS

POWER

POWER FAULT

SYSTEM FAULT

EARTH FAULT

FAULTOUPUTSTATUS

ANCILLARYOUTPUTDISABLED

FIRE OUTPUTSTATUS

TEST

AMPAC

SYSTEM IS NORMAL

ALARMSDELAY

ACTIVEFIRE FAULT

FIRE OUTPUTONALARMS STATUS

DISABLED

NORMAL ENABLE

EVACUATERE S E TSILENCE

BUZZER

SILENCE

RE S OUNDOVERRIDE

FFFiiirrreee AAAlllaaarrrmmm CCCooonnntttrrrooolll PPPaaannneeelll

EEENNN555444 222 &&& 444 111999999777

Our aim is to provide Consistently Excellent Service in the eyes of our customers

Installation &Commissioning

of

Control & MonitoringAdd Ons

PLUS


2/28


3/28

Installation & Commissioning of Control & Monitoring Add Ons

Page 1

Table of Contents Page No.

1 About This Manual...............................................................................................21.1 Purpose ...............................................................................................................21.2 Scope...................................................................................................................21.3 References ..........................................................................................................21.4 PCB Removal / Replacement.............................................................................3

2 Wiring to the Main Card BRD25MCB ................................................................. 32.1 Communications ................................................................................................3

3 Adding Control and Monitoring Facilities ......................................................... 43.1 Internal Communications Connector (RS485).................................................43.2

Programming ......................................................................................................4

4 Installation and Wiring of Add On Cards and Boards...................................... 44.1 Address Setting and Terminating the Communications Bus ........................54.2 Input Board BRD25SIPB ....................................................................................64.3 Relay Board BRD25EWRB.................................................................................64.4 Fire Fan Module BRD25FCB..............................................................................74.5 Fan Termination Board BRD25FTB..................................................................84.6 General Indicator Card BRD25GIB -A...............................................................84.7 Switch and Indicator Card BRD25GIB - B ........................................................94.8 Zone Mimic Indicator Card ( Int. Pwr. ) BRD25GIB -C.....................................94.9 Zone Mimic Indicator Card ( Externally Powered. ) BRD25GIB -C ..............104.10 LED Annunciator Master ( LAM ) BRD25GIB - E ...........................................104.11 Sounder Board BRD25SOPB -A......................................................................11

5 Agent Release.................................................................................................... 115.1 Operation...........................................................................................................115.2 Agent Release Module BRD25ARB - A...........................................................145.3 Local Control Station BRD25ARB - B.............................................................155.4 Common Agent Release Module and Local Control Station Indicators.....165.5 Agent Release Termination Board BRD25ATB .............................................175.6 Interface Wiring ................................................................................................18

6 Appendix: Adding to the System Menu & Programming...............................207 Status and Programming Screens................................................................... 22

7.1 Level 1 to 3 Status Screens.............................................................................227.2 Level 3 System Programming .........................................................................237.3 Level 3 Programming Menu.............................................................................24


4/28


Page: 2

1 About This Manual

1.1 PurposeThis manual is an instructional tool for the installation and commissioning, of add on ancillary

cards, modules and boards that can be fitted to the ZoneSense PLUSFire Alarm Control Panel(FACP) and should be read in conjunction with the main Installation and Commissioning Manual.

1.2 ScopeThe information within this manual is only available to and for the use of personnel engaged in

the installation and operation of theZoneSense PLUSFACP.

ZoneSense PLUS has been designed to comply with major world standards. To ensure thesestandards are not compromised in any way installation staff and operators should;

1. be qualified and trained for the task/s they undertake;

2. be aware this manual should be read prior to the installation and commissioning of theZoneSense PLUSFACP;

3. observe anti-static pre-cautions at all times; and

4. if a problem is encountered or there is any doubt with respect to the operational parametersof the installation the supplier should be contacted.

1.3 References

ZoneSense PLUSTechnical ManualZoneSense PLUSOperation &Programming ManualZoneSense PLUSInstallation and Commissioning ManualApollo Detector / Device ManualsAmpac Product Data SheetsBritish Standard EN54 Parts 2 & 4European Standard BS 5839

FIRE

ZONE 1

ZONE 2

ZONE 3

ZONE 4

ZONE 5

Z ONE 6

ZONE 7

ZONE 8

FAULT / D ISABLED/TEST

CANCEL

MENU

IENTE R

SYSTEM STATUS

POWER

POWER FAULT

SYSTEM FAULT

EARTH FAULT FAULT OUPUTFAULT/DISABLED

ANCILLARYOUTPUTDIS ABLED

ALARMS/FAULTDISABLED

TESTAMPAC

SYSTEM IS NORMAL

ALARMSDELAY FIRE FAULT

FIR E OUTPUT O N FIR E PUTPUTFAULT/ DISABLED

DISABLED

NORMAL ENABLE

EVACUATERESETSILENCEBUZZER

SILENCERESOUNDOVERRIDE

Figure 1: Examples of the ABS, Metal Cabinet and Metal Cabinet with Battery Box


5/28


Page: 3

1.4 PCB Removal / Replacement

If the PCBs have to be removed the following precautions should be observed;

1. Removing the door will provide better access to the boards and ensure the hinges arenot accidentally stressed.

2. Personal anti- static procedures must be followed.

3. When disconnecting the telecom style connecting cable from the PCB, make sure thatthe cable remains connected to at least one board to prevent it being misplaced.

Note: Care should be taken when detaching this connector as it is necessary to depress thesmall locking tab to unlock the connector from itsbase. To reconnect the cable the connector must firstbe correctly aligned then pushed into the socket so itlocks into position.

4. Carefully remove the retaining screws at each

corner of the board taking care not to damageany of the components.

5. Place each board into anti- static storage once removed.

2 Wiring to the Main Card BRD25MCB

2.1 Communications

External Communications Terminals (RS485) TB2 1, 2 & 3The RS 485 output drives the remote cards and mimics up to a distance of 1.2km from the panelitself. The external cabling (2x2 shielded pair plus power) is wired to TB2 +, - and earth.

Note: If a fault occurs on the communications line the common FAULT and SYSTEM FAULTLEDS will be illuminated. The fault details can be displayed by selecting the Faults Menu.

Remote CardsThe number of cards that can be installed on the external communications bus are:

8 x Remote LED Mimics. 1 x 8 Way Remote Relay Output Board. This board provides 8 sets of normally open

(NO), normally closed ( NC ) and Common ( C ) voltage free contacts rated at 1A @30V.

Main Card Comms Link K1K1 MUST be inserted when only the front door panel cards and the Main Card are used as anFACP. If this is not the case and TB2 is cabled to LED mimics and / or 8 Way Remote Relay

Boards a link is inserted in the last board to complete the communication circuit orif boards aremounted on the back pan and communications are wired from the Main Card then the last boardin this chain MUST be terminated.

K1

Comms + -Comms Link

TB2

Top Left Hand Cornerof the Main Board

To LED Mimics and/orRemote Relay Boards

TB3

SP C/C ALT

Spare I/P

Class Change I/P

Alert I/P

Inputs

RS485 Com 1 2 3

Note:the shield iswired to

Shield

Figure 2: Wiring Detail

Push Tab Inwardsand Gently Pullthe ConnectorFrom the Socket

Connector


6/28


Page: 4

3 Adding Control and Monitoring Facilities

A combination ofone of each type of board / card, but not all of them, can be mounted on theback pan or the front panel of the FACP to provide additional features to a standard panel. Allboard inputs or outputs are programmable to any combination of zones.

Relay Board, BRD25EWRB A or with a change of on board components it canalso be installed remotely on the external communications bus as a RemoteRelay Board BRD25EWRB -B

Input Board BRD25SIPB -. Sounder Board BRD25SOPB. Brigade Interface Board BRD25BBA. Fire Fan Module consists of a Termination Board ( BRD25FTB and front panel

card BRD25FCB -. Agent Release Module consists of a Termination Board ( BRD25ATB ), front

panel card ( BRD25ARBA ) and if required a remote local control station(BRD25ARBB).

General Indicator Card. BRD25GIB -A Switch and Indicator Card BRD25GIBA Zone Mimic Indicator Card ( Internal Power ) BRD25GIB -C Zone Mimic Indicator Card (External Power normally remote) BRD25GIB -D

Note: To add or remove Cards from the FACP programming go to the SYSTEM Menu.3.1 Internal Communications Connector (RS485)PCB mounted connectors provide serial communications to internal ancillary boards. CN9 on theMain Card cables to CN1 or 2 on the front panel boards and CN5 on the Main Card cables toCN1 or 2 on the back pan boards

3.2 ProgrammingRefer to the Operation and Programming Manual to program the above options into the FACP.

Note: The Configuration label should be updated once the panel has been upgraded.

4 Installation and Wiring of Add On Cards and Boards

CAB1925 to Batteries

CAB1902

CAB1905

CAB1911 TO MAINS EARTH

CN1CN2 CN2 CN1ALARM2

N/CCOMN/0BATTFAIL

N/CCOMN/0ISOLATE

N/CCOMN/0FAULT

N/CCOMN/0ALARM1

N/CCOMN/0

TB1-TB5

POWER

0V

+27V

0V

+27V

CN2

CN1

CN3CN4

POWER

+27V

0V

CN1

CN2

+27v Power fitted when Relay or Termination Boards are fitted

CN1

CN2

CN5

CN9

CN1CN2CN2 CN1

CAB2200 CAB2117

CAB1905

CAB2200

CN6

POWER

+27V

0V

CN1

CN2

POWER

+27V

0V

CN1

CN2

MAIN CONTROL CARD

OPTIONAL CARDSAGENT RELEASEFAN CONTROLGENERAL INDICATOR

OPTIONAL BOARDSAGENT TERMINATIONRELAYFAN TERMINATIONINPUTSOUNDER TERMINATION

A BATT BOX IS REQIF THESE BRDS ARE FITTED

OTIONALBRIGADE BOARD

CAB2200

CAB2200

BRD25ARB PCB0783 (AGENT RELEASE MODULE)BRD25ATB PCB0787 (AGENT TERMINATION BOARD)BRD25BBA PCB0779 (BRIGADE BOARD)BRD25EWRB PCB0770 (8 WAY RELAY BOARD)BRD25FCB PCB0783 (FIRE FAN MODULE )

BRD25FTB PCB0780 (FAN TERMINATION BOARD)

PSU1887

CN3

CN4

CN3 CN4

CN3

CN4

BRD25GIB PCB0781 (GENERAL INDICATOR CARD)BRD25MCB PCB0769 (MAIN CONTROL CARD)BRD25PSU PCB0813 (POWER SUPPLY UNIT)BRD25SIPB PCB0778 (SINGLE INPUT BOARD)BRD25SOPB PCB0772 (SOUNDER OUTPUT BOARD)

OPTIONAL CARDSAGENT RELEASEFAN CONTROLGENERAL INDICATOR


A BATT BOX IS REQIF THESE BRDS ARE FITTED


A BATT BOX IS REQIF THESE BRDS ARE FITTEDBUS 1

BUS 2

BUS 3

BOARDIDENTIFIERS:

CN8

CN10

Figure 3: Typical Wiring, Ancillary Card and Board Positioning Within the ABS FACP


7/28


Page: 5

4.1 Address Setting and Terminating the Communications Bus

Address Setting ( SW1 )

Except for the LED Mimics in ZoneSense PLUSFACPs there can only be one (1) Board / Card of

each type so the address on each board is set to 1.

Note: There can be up to 8 remote LED Mimics so the address of each is set from 1-8 dependingon the number Mimics in the system. The information displayed at each location will be identical.

DIL Switch: ON = 1, OFF = 0Address 1234 Address 123401 1000 05 101002 0100 06 011003 1100 07 111004 0010 08 0001

Figure 4:Address Table & Example of Switch ( SW1 ) Set to 1

Terminating the Communications BusLK1 is the EOL Link and must be inserted on the last board on each communications bus. If not,a communications fault can occur.

TB2

K1

Shield

CN 5

CN 9Front Panel

Card 1Front Panel

Card 2

BackpanBRD 1

BackpanBRD 2

INSERTLK1

RemoteCard 1

RemoteCard 2

LCS 1 LCS 2

INSERTLK1

INSERT

LK1

INSERTLK1

If Agent Release is fitted to the FACP there will be an Agent Termination Board mounted on the Backpan.Local Control Stations can then be fitted at some location remote from the FACP. These LCS's communicatewith the ATB via a second RS485 bus hence the last LCS in the chain will have to be terminated

Note: If Backpan boards AND remote facilitiesare fitted the front panel cards are not terminated

ToTB1 Agent Termination Board

Fit K1 if only theMain ControlCard is used asthe FACP or1 Bus is used

RS485 +-

BUS 1 ( B1 )

BUS 2 ( B2 )

BUS 3 ( B 3)

( Link 1 in Table below )



BUS 4 ( B 4)Fit LK1 to last LCS

Figure 5: RS485 Communication Bus Terminating

Linking TableLink Bus Configuration

B1 B1,2 B1,3 B1,2,3 B,2 B2,3 B31 X & K1 X X

2 X X X & K1 X

3 X X X X & K1

X = Insert LinkB1: Bus 1 to Front Panel CardsB2: Bus 2 to Backpan BoardsB3: Bus 3 to Remote facilitiesB4: Bus 4 Local Control Station cabled to the backpan Agent Release Board.

Note: Programming and the communication process allows the Main Card to identify the type ofboard it is communicating with.

1 2 3 4

On


8/28


Page: 6

4.2 Input Board BRD25SIPB

DescriptionThe Input Board makes provision for 16 voltage free contacts to be terminated to 16 opticallycoupled inputs. Its application is primarily for the monitoring of controlled ancillary equipment or toinitiate an action / event due to a change of state from what is accepted as the norm.

ConnectorsCN1 Is designated as the input Comms .CN2 Is designated as the output Comms to the next board.CN3 27 Volts into the Board. Quiescent Current:2.6mACN4 27 Volts to the next Board unless it is the last board in the chain then it is left empty.

Terminal BlocksTB 2 9 Taking note of the Common 0v terminals connect the voltage free contacts as shown

below. Note: only the first 8 are functionally programmable in ZoneSense PLUS

SW1 There can only be 1 Input Board so the address on each board is set to 1.

LK1 Is the EOL Link and is inserted should the board be the last in the chain. If notinserted on the last board the Main Card will initiate a communications fault.

SW1

LK1 EOL Termination Address SWSET to 1

INPUTS1 2 3 4 0V INPUTS5 6 7 8 0V INPUTS9 10 11 12 0V INPUTS13 14 15 16 0V0V

16 Inputs are Voltage Free Contacts

27 VIn

27V To CN3 of Next Board

TB9TB8TB7TB6TB5TB4TB3

RS485 Control In From CN2 of thePrevious Board or CN5 of the Main Card

RS485 Control Out to NextBoard or Link 1 EOL is Applied

CN2

CN1

CN3 CN4

TB2

1 2 3 4

ONON

Inputs

1 2 3 4

0V Inputs

5 6 7 8

0V Inputs

9 10 11 12

0V Inputs

13 14 15 16

0V0V

16 Inputs are Voltage Free Contacts

TB9TB8TB7TB6TB5TB4TB3TB2

8= 0 Volts = Input

+-

#1. 27 Volts In from CN10 on the Main Card or CN4 of the previous internal board.

#2. Select an appropriate length cable from those supplied to connect Comms & 27V.

Note: Only the first 8 Voltage Free Contacts are functionally programable.The second 8 can be used to independently drive LEDs 8 to 16 on theGeneral Indicator Board.

Figure 6: Typical Input Wiring and Board Layout

4.3 Relay Board BRD25EWRB

Relay Board ( Internal ) BRD25EWRB -A

The Relay Board has provision for 8 X 1 Amp voltage free change over contacts for control ormonitoring purposes. Communication and control cabling is the same as all other internal boards.

Quiescent Current:2.4mA

LK1 EOL Termination

Address SWSET to 1

27 VIn

27V To CN3 of Next Board



CN2

CN 1

CN3 CN4 ON+-

#1. 27 Volts In from CN10 on the Main Card or CN4 of the previous internal board.

#2. Select an appropriate length cable from those supplied to connect Comms & 27V.


SW 1

O/P 8N/CCOMN/0

O/P 7N/CCOMN/0

O/P 6N/CCOMN/0

O/P 5N/CCOMN/0

O/P 4N/CCOMN/0

O/P 3N/CCOMN/0

O/P 2N/CCOMN/0

O/P 1N/CCOMN/0

1 2 3 4

ON


O/P 8N/CCOMN/0

O/P 7N/CCOMN/0

O/P 6N/CCOMN/0

O/P 5N/CCOMN/0

O/P 4N/CCOMN/0

O/P 3N/CCOMN/0

O/P 2N/CCOMN/0

O/P 1

N/C

COM

N/0

N/0 = Normally Open

COM = Common

N/C = Normally Closed

Figure 7: Board Layout


9/28


Page: 7

Relay Board ( Remote ) BRD25EWRB - B

In the remote version the Comms In and Out Terminal Block TB9 is cabled to the RS 485 Commsterminal block TB3 on the Main Card 302 7690 or LED Mimic and can be installed up to 1.2kmsfrom the FACP.

Note#1: This version can be powered from the panel or an external 27 volt source due to the onboard switched mode supply. Quiescent Current of both boards is 16mA

Note#2: In a system there can only be either a remote OR an internal board, not both.

Figure 8: Remote Relay Board Layout

4.4 Fire Fan Module BRD25FCB

The Fire Fan Module has four ( 4 ) separate fan controls each having an On, Auto and Offfunction switch and a set of three (3) monitoring LEDs. The LEDs indicate the status of theequipment eg. Run, Fault or Stop. The two ( 2 ) arrow head keys are used to step up and / ordown through the three ( 3 ) conditions. A slip in label can also be inserted into the hinged coverfor identification purposes.

Quiescent Current: 13.5mA

Slip In

Label

Card & PCB Securing Tabs( Top & Bottom )

PCB

ClearPlasticClipInLabel

Clip OnPlastic Surround( Push down here and pullout to remove and insert labels )

WINDOWS

WINDOWS

FOR SLIP

IN LABELS

Lettering on slip inlabels must be atleast 5mm in height.

K2 Termination Link

In Out

Address

SwitchSet to 1

1

2

3

4

ONCN1

CN2

CN1: Communications & 27V IN from CN2 off the previousFront Panel Card or CN9 on the Main Card

CN2: Communications & 27V OUT to Next Front Panel Card.If Unsed the Termination Link Must be Inserted.

Top Front Card &PCB Securing Clips

Bottom Front Card &PCB Securing Clips

Figure 9: Fire Fan Module Front Panel Figure 10: Fire Fan Module PCB Layout

U4

CN 3

CH4

RL8RL7RL6RL5RL4RL3RL2RL1

X1

U5

U3

U2

U1

TB8TB7TB6TB5

TB9

TB4TB 3TB2TB1

LK1

HY1 U6

SW1

M10

TB10

0V0V +27VDC+27VDC

EXTERNALPOWER

rev.1

EC3AW

A B COM

EOL Termination

///

N O N C

C

///

N O N C

CC

NCNO

///

C

NCNO

//////

N O N C

C

CN

C

NO

///

///

NO

NC

C///

NO

NC

C

O/P 8N/CCOMN/0

O/P 7N/CCOMN/0

O/P 6N/CCOMN/0

O/P 5N/CCOMN/0

O/P 4N/CCOMN/0

O/P 3N/CCOMN/0

O/P 2N/CCOMN/0

O/P 1N/CCOMN/0

TB1-TB8

A B COM

COMMS IN / OUT Address SW

To TB3 on the MainCard and/or LED MimicIn Out

27V

1 2 3 4

ON

Contact Legend:N/O = Normally OpenN/C = Normally ClosedC = Common


10/28


Page: 8

4.5 Fan Termination Board BRD25FTB

The Fan Termination Board interfaces between the Fire Fan Module and the plant/equipment itcontrols via the 24 volt 250mA Start, Stop, current limited, relay outputs and monitor inputs.Programmable monitoring of the field equipment is achieved using 0 volts as an input level toindicate run, fault and stop conditions of that equipment. Monitoring is programmed in theFunction Menu for a 3, 4 or 5 Wire Start / Stop, Run, Fault, Stop & Common functions. The inputsare protected by way of resetable transorbs and resistive / capacitive networks.

Quiescent Current: 6.5mA

ConnectorsCN1 RS485 Control IN from previous board or Main CardCN2 RS485 Control OUT to next board or LK1 EOL termination is appliedCN3 27 VDC IN from CN10 of the Main Card or CN4 of the previous boardCN4 27 VDC OUT

Terminal BlocksTB2 5 Are used to connect the fan control and monitoring wiring to the board.

SW1

TB4TB3TB2

LK1

TB5

EOL Termination

0V+27V

POWER

Address SW

FAN 1FAN 1STOP COMSTOPFLTRUN

FAN 2STOP COMSTOPFLTRUNSTART

FAN3FAN 3STOP COMSTOPFLTRUNSTART

FAN 4COMSTOPFLTRUNSTART

FAN4STOPSTART

FAN 2

CN1

CN2

CN3 CN4

RS485 Control in from CN2 of Previous Board or CN5 of the Main Card

RS485 Control Out to Next Board or Link 1 EOL is Applied

27V In from CN 10 on the Main Card or CN4 of the Previous Board

27V Out to Next Board if Applicable

1 2 3 4

ON

STOP

COM

STOP

FLT

RUN

START

TB 2, 3, 4 or 5

Cabling from FACPto Plant / Equipment

1 2 3 4 5 6

FAN CONTROLSOLID STATE ORRELAY INTERFACE

FAN MONITORING

0VINPUTS 1, 2 & 3+24V O/Ps

RUN

Figure 11: Fan Termination Board Layout and Typical I/O Wiring

4.6 General Indicator Card BRD25GIB -A

IMPORTANT

Note: The Cards BRD25GIB A, B, C and D all have a common PCB. What sets them apart fromeach other is not only the function they perform but how the componentry is loaded onto the cardto perform that function.

This Card indicates / displays the status of the inputs on the 16 Way Input Termination Board byway of Program selectable tri-coloured LEDs with its function being identified on the front panelby slip in labels.

Quiescent Current: 3 to 3.5mA depending on the application


PCB

Clip OnPlastic Surround( Push down here and pull

out to remove and insert labels )

Lettering on slip inlabels must be atleast 5mm in height.

WindowsforSlip in Label

Slip In Label

K2 TerminationLink

In Out

AddressSwitchSet to 1

1

2

3

4

ON

CN1

CN2

CN1: Communications & 27V INfrom CN2 off the previous FrontPanel Card or CN9 on the Main Card


Top Front Card &PCB Securing Clips

Bottom Front Card &PCB Securing Clips

Figure 12: Front Panel Card Layout Figure 13: Front Panel Card & PCB Layout


11/28


Page: 9

4.7 Switch and Indicator Card BRD25GIB - BThis Card can effectively perform 2 different functions. Firstly the indicators monitor the first 8inputs of the 16 Way Input Termination Board while secondly the switches can be programmed tomanually operate a specific relay in the system.



PCBClearPlasticClipInLabel

Clip onPlastic Surround( Push down here and pull

out to remove and insert labels )

Note: As per AS 1668lettering on any of theslip in labels must beat least 5mm in height.

WindowsforSlip inLabel

Slip In Label

WINDOWS FORSLIP IN LABEL

K2 TerminationLink

In Out

AddressSwitch

Set to 1

1

2

3

4

ON

CN1

CN2



Top Front Panel Card &PCB Securing Clips

Bottom Front Panel Card &

PCB Securing Clips

Figure 14: Front Panel Card & PCB Layout

4.8 Zone Mimic Indicator Card ( Int. Pwr. ) BRD25GIB -C

The internally powered Zone Mimic Indicator Card connects to the FACP 27 volt power supplyand the internal communications bus for indication control. The card provides remote visualindication of any Zone in an Alarm and / or Fault / Isolate condition. A maximum of 8 of thesecards can be connected to, or daisy chained together, on any one system. Slip in labels identifythe monitored Zone. The Alarm LEDs flash for an un acknowledged alarm and are steady foracknowledged. The Fault / Isolate LEDs flash for a Fault condition and are steady if a Zone isIsolated.

Quiescent Current:14mA


Clip OnPlastic Surround( Push down here and pullout to remove and insert labels )

Lettering on slip inlabels must be at

least 5mm in height.

Slip In Label

PCB

AlarmIsolateFault

Windows for

Slip in Label

K2 TerminationLink

In Out

AddressSwitchSet to 1

1

2

3

4

ON

CN1

CN2



Top Front Panel Card &PCB Securing Clips

Bottom Front Panel Card &PCB Securing Clips

Figure 15: Front Panel Card & PCB Layout

Note: Except for CN1 & 2 being fitted and TB1, HY1 the Buzzer and CN6 not being fitted theunderside of this card is the same as for the externally powered card.


12/28


Page: 10

4.9 Zone Mimic Indicator Card ( Externally Powered. ) BRD25GIB -C

The externally powered Zone Mimic Indicator Card operates in the same way as does theinternally powered version. The only difference is that the 27 volt power supply is independent ofthe FACP. This card would be used when the distance involved causes a significant voltage dropsuch that it may effect the reliable operation of the system or the costs involved in the cable is

offset by the availability of a remote 27 volt supply.

Quiescent Current:13mA ( This current applies to both cards )

Figure 16: PCB Front Layout Figure 17: Underside of PCB

4.10 LED Annunciator Master ( LAM ) BRD25GIB - E

The LAM provides remote stand alone FACP status, Alarm and Fault / Isolate Indication of 8zones. Two push buttons, Lamp Test and Silence Buzzer, provide for local testing of theindicators and buzzer while the buzzer duplicates that at the FACP. A maximum of 4 LAMs withaddresses of 1 to 4 may be cabled to an FACP.

Card & PCB Securing Tabs ( Top & Bottom )

Lettering on slip inlabel must be atleast 5mm in height.

Slip In Label

PCB

AlarmDisableFault

Windows for

Slip in LabelFIRE

FAULT

DISABLED

ALARMS STATUS

FIRE OUTPUT STATUS

TEST

DELAYACTIVE

POWER

LAMP

TEST

SILENCE

BUZZER

FIRE

FAULT/DISABLED

Release of the Clip On Surround( Metal Cabinet: Push down here and pull out to remove and insert label.ABS Cabinet: At the top RH cornner of the surround insert the surround removaltool between it and the front panel then slide along the surround to release)

PWR OUT

PWR IN

+

0V

+24V

CO M

-RS485 OUT TO NEXT LAM( IF APPLICABLE )

INPUTMUTE

BUZZER

LK1TERMINATION LINK

SWITCHADDRESS

CN 6

O

N

1

2

3

4

0V

+24V

+

CO M

- RS485 COMMS IN FROM FACP OR PREVIOUS LAM

ON

1

2

3

4

ON

1

2

3

4

ON

1

2

3

4

ON

1

2

3

4

LAM4

LAM3

LAM2

LAM1

LINK IS INSERTED ON THELAST CARD IN THE CHAIN

LAM 1 - 4ADDRESSSETTING

Figure 18: LAM Front Panel and PCB Layout

TB1

SW13

HY13V3 Supply Buzzer BZ1

CN6

0V

+

0V

+

BuzzerMuteInput

AddressSwitch

EC3AW

RS 485In

CO M

RS 485Out -

CO M

+

-

+

TerminationLink K2

27VIn

27VOut

1

2

3

4

ON

+

D17

D18

D19

D20

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

D11

D12

D13

D14

D15

D16

D21

D22

D23

D24

D25

D26

D27

D28

D29

D30

D31

D32

U1

U2

U3

U4U5

U6

U7

U8

X1


13/28


Page: 11

4.11 Sounder Board BRD25SOPB -A

The Sounder Board expands the number of sounders that can be used on an FACP to 8. Each

solid state output is rated at 24VDC / 500mA. and requires a 10K End of Line (EOL) resistorregardless whether or not a sounder is wired to the circuit.

Quiescent Current: 5.6mA Maximum Current per Output: 500mA

Figure 19: Wiring Detail & PCB Layout

Note: Sounder polarity MUST be observed.5 Agent Release

Control consists of the FACP Agent Release Module and Termination Board. Should control berequired at a point remote from the FACP an Agent Release Local Control Station can beincorporated .

5.1 Operation

IntroductionThe Agent Release Module and Termination Board communicate with the FACP via the RS485multi-drop bus.

The Agent Release Local Control Station communicates only with the Termination Board via aseparate RS485 bus. Up to 4 Agent Release Local Control Stations can be connected to onetermination board.

The Agent Release Module operates in three modes;1. Automatic/Manual;2. Manual Only; and3. Disable.

The mode is selected by operating the keyswitch switch on either or module.

The keyswitch at the Agent Release Module is the only keyswitch with a Disable selection andhas the highest priority. Hence when the keyswitch is in the Disable position all other keyswitches

are ignored and the agent control system is in the Disabled mode.

Next priority is Manual Only. If any keyswitch is in Manual Only (providing the keyswitch at theAgent Release Module is NOT in Disable), then the board is in the Manual Only mode.

Finally, the system is in the Auto/Manual mode when all keyswitches are in Auto Manual.

The pressure switch input on the termination board (which is used to confirm that the agent hasbeen released) can be configured to accept a normally open contact, normally closed contact, orignored. This is selected via the FACP on-site programming.

TB3 TB2 TB1

SW 1

-VE+VESOUNDER 1

-VE+VESOUNDER 2

-VE+VESOUNDER 3

-VE+VESOUNDER 4

-VE+VESOUNDER 5

-VE+VESOUNDER 6

-VE+VESOUNDER 7

-VE+VESOUNDER 8DC IN

0V 27V

LK1 EOLTermination

Address SW

POWER

CN2

CN1

27V IN- +

To Sounders 1 to 4 + / - To Sounders 5 to 8 + / -

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

1 2 3 4

ON

TB3 TB2 TB1-VE+VE

SOUNDER 1-VE+VE

SOUNDER 2-VE+V E

SOUNDER 3-VE+V E

SOUNDER 4-VE+V E

SOUNDER 5-VE+VE

SOUNDER 6-VE+VE

SOUNDER 7-VE+V E

SOUNDER 80V 27V

To Sounders 1 to 4 + / - To Sounders 5 to 8 + / -



ONNote: Sounder polarity MUST be observed

27V IN- +


14/28


Page: 12

Disabled ModeDisabled mode is selected by placing the keyswitch at the Agent Release Module in the Disabledposition. This electrically isolates the activation circuit, and results in the following: Disabled indicators at the Agent Release Module and Local Control Station are lit. Agent Release Module and Local Control Station buzzers sound. No automatic releases can be commenced.

System inoperative output is activated.

Note:Disabled mode can not be overridden.Manual ModeWhen the board is in manual mode, then the Manual Only indicators at the Agent Release Module and Local Control Station are lit No automatic release sequences can be commenced. Does not interrupt a release sequence that has started System inoperative output is activatedTo manually discharge the agent, the Manual Release facility at the Agent Release Module or theLocal Control Station is activated.

The manual release sequence is: Manual Release Activated indicators are lit on the Agent Release Module and Local

Control Station Stage 1 outputs are switch to +24VDC. Stage 2 outputs are pulsed during the pre-release delay to +24VDC. Start optional pre-release delay. (Selected via FACP on-site programming). Upon expiration of the delay, activate the selected activation circuit and stage 2 outputs

becomes steady Light the agent released LED on the Agent Release Module and Local Control Station

when pressure switch input on the termination card is activated or immediately (dependson the pressure switch configuration).

FACP to activate the FIRE output and light the FIRE LED

The discharge sequence can be interrupted by the activation of the Hold input. Activation of theHold input prevents the release of the agent. When the Hold switch is released, the pre-releasedelay is restarted. While the Hold input is activated, the stage 2 output is switched off, and thebuzzer will sound.

Auto/Manual ModeIn this mode, automatic and manual discharge is possible. For manual discharge see above.

The automatic discharge sequence is initiated when one or two zones go into alarm.

With single zone alarm activation the following discharge sequence is executed. Auto Activation indicator is lit on the Agent Release Module and Local Control Station

Stage 1 outputs are switched to +24VDC Stage 2 outputs are pulsed during the pre-release delay to +24VDC Start optional pre-release delay (Selected via FACP on-site programming). Upon expiration of the delay, activate the selected activation circuit and stage 2 outputs

becomes steady. If configured light the agent released LED on the Agent Release Module and Local Control

Station when pressure switch input on the termination board is activated. FACP to activate the FIRE output and illuminate the FIRE LED. The operation of the Hold switch is as per the manual release

With dual zone activation, if the first zone goes into alarm, then the following steps are followed; Flash the auto release activated LED at the Agent Release Module and

Local Control Station

Stage 1 outputs are switched to +24VDC


15/28


Page: 13

When the second zone goes into alarm, then the following steps are followed Auto release activated LED on the Agent Release Module and Local Control Station goes

steady Stage 2 outputs are pulsed during the pre-release delay to +24VDC Start optional pre-release delay. (Selected via FACP on-site programming).

Upon expiration of the delay, activate the selected activation circuit and stage 2 outputsbecomes steady. Light the Agent Released LED on the Agent Release Module and Local Control Station

when the pressure switch input on the termination board is activated (depends on thepressure switch configuration).

FACP to activate the Fire output and illuminate the Fire LEDThe operation of the Hold switch is as per the Manual Release.

Released ConditionWhen the agent has been released, and the pressure switch input has been activated, then theboard is in the released condition. The condition is shown by: Agent Released indicator is lit at the Agent Release Module and Local Control Station FACP Fire output and associated indicator is On.

The condition remains until reset has been activated at the FACP.

It is possible, when the agent release module is in the released condition to de-activate the Stage1 and Stage 2 outputs. This is achieved by depressing the SILENCE/RESOUND button at theFACP. This action will also silence the alarm outputs at the FACP and the sounder outputs on the8 way sounder board (if fitted). If the SILENCE/RESOUND button is depressed again to instigatethe RESOUND facility, then the stage 1 and stage 2 outputs will be re-activated (as will theonboard alarm outputs and sounder outputs on the 8 way sounder board if fitted).

Lock-Off ValveWhen the lock-off valve is operated, the agent is blocked from reaching the release valve. Whenthe lock-off valve is operated, the following occurs: Light the Blocked Mode indicator at the Agent Release Module and Local Control Station

Operates the system inoperative output

Fault MonitoringThe sources of fault in the system are: Pressure switch monitoring circuit Low pressure switch monitoring circuit Lock-off valve monitoring circuit Activation circuit Stage 1 outputs Stage 2 outputs Fault in the trigger zones Fault with a Local Control Station

Note #1: The common fault indicator on the Agent Release Module and Local Control Station isilluminated for any Fault condition.

Note #2: For a pressure switch fault, low pressure switch fault, lock-off valve fault, stage 1output fault and stage 2 output fault the FACP will signal the brigade.

Note #3: When there is a fault in the activation circuit or in the trigger zones, in addition to theabove, the system inoperative output is operated.

Note #4: The FACP buzzer sounds for all faults and the LCD displays the type of fault.

Note #5: The FACP will report the type of fault on the LCD.


16/28


Page: 14

IsolationIf the trigger zones are isolated by the FACP, then the trigger zone isolated indicator at the AgentRelease Module and Local Control Station is illuminated, and the system inoperative output isoperated.

Disablement of the Trigger Zones

If the trigger zones are disabled by the FACP, then the isolate indicator at the FACP is illuminatedand the system inoperative output is operated.

5.2 Agent Release Module BRD25ARB - A

The Agent Release Module controls and monitors all the requirements for agent release andcarries the slide in label for identification of the agent and application area.

Keyswitch

PCB

Manual ReleaseSwitch

AUTO / MANUAL MANUAL ONLY

MANUAL HOLD

MANUAL RELEASEACTIVATED

AUTO RELEASEACTIVATED

RESERVE AGENT

TRIGGER ZONEDISABLED

INITIAL AGENT

AGENTRELEASED

BLOCKED MODE

COMMON FAULT

DISABLED

MANUAL

ELEASE

R

MANUALDISABLED

AUTO / MANUAL

HOLD

AGENT SELECT

MANUALONLY

Figure 20: Exploded View of Module and Front Panel Layout

Controlled AccessIt is a requirement that control be secured from unauthorised use. For this reason a key switchhas been included in the control process.

DISABLED

AUTO / MANUAL

MANUALONLY

Disabled, Manual Only, Auto/Manual Keyswitch In disabled mode theselected activation circuit is electrically isolated from the activation device, and the agent can notbe released. In manual only mode, the agent can only be released manually, and in Auto/Manualmode the agent can be released automatically or manually.

Note:The key is removable in all positions.

MANUAL HOLD

Manual Hold When activated, delays the discharge of the agent. When the switchis depressed during the pre-discharge delay, the delay is restarted when the switch is released. Ifdepressed at any other time a fault is registered after a 10 second debounce time out period.

AGENT SELECT

Agent Select When activated, causes the selected agent to toggle between Initialand Reserve.

MANUAL

ELEASE

R

Manual Release When activated causes a manual release of the agent, providing

the system is operative.


17/28


Page: 15

Agent Release Module PCB Layout

The PCB is fitted with two 2 x RJ45 connectors CN6 & 7 for power (27VDC) and communications(RS485) for communications between the Module and the FACP Main Card.


D10

D9

D14

D13

D12

D11

D6

D5

D4

D3

D8

D7

U4

U1

U2

U3

X1

Select

Manual ReleaseActivated

Initial Agent

Manual Hold

Auto / Manual

Auto ReleaseActivated

Reserve Agent

Trigger ZoneDisabled

Manual Only

AgentReleased

Blocked Mode

Common Fault

Disabled

Hold

CutoutCutout

SW 2

CN 2

TP9

Key Switch

AddressSwitch

RS485&

+/- 27vIn

RS485&

+/- 27vOut

1

2

3

4

O

NK1

TerminationLink

CN 8

Manual Release

CN 6 CN 7

Figure 21: Front Panel PCB Layout Figure 22: Underside of the Front Panel PCB

Note: If the keyswitch is not used CN2 will carry a link so as to activate the panel.5.3 Local Control Station BRD25ARB - BExcept for the agent select button, and the keyswitch only offering the Auto/Manual and ManualOnly selection the Local Control Station has the same indicators and controls as the AgentRelease Module.

AUTO / MANUAL MANUAL ONLY

MANUAL HOLD

MANUAL RELEASEACTIVATED

AUTO RELEASEACTIVATED

RESERVE AGENT

TRIGGER ZONEDISABLED

INITIAL AGENT

AGENTRELEASED

BLOCKED MODE

COMMON FAULT

DISABLED

MANUAL

ELEASE

RMANUAL

MANUAL ONLY

AUTO / MANUAL

HOLD

Keyswitch

PCB

Manual ReleaseSwitch

Figure 23: Local Control Station Layout

MANUAL

ELEASE

R

Manual Release Pressing the push button starts the manual agent releasesequence. This two action safety feature prevents any accidental operation of the control andshould not be disabled.

MANUAL

HOLD

Manual Hold When pressed places the system into manual mode and prevents theinitiation of the automatic discharge sequence.


18/28


Page: 16

5.4 Common Agent Release Module and Local Control Station Indicators

MANUAL RELEASEACTIVATED Manual Release Activated

Red in colour. Lit when a manual agent release sequence has commenced. This can beinstigated from the Agent Release Card and Local Control Station.

AUTO RELEASEACTIVATED Auto Release Activated

Red in colour. Lit when a automatic agent release sequence has commenced. This occurs whenthe zone(s) on the FACP have gone into alarm. For dual zones, the indicator should flash whenthe first zone goes into alarm, and steady when the second zone goes into alarm.

AGENTRELEASED Agent Released

Red in colour. Lit when the pressure switch indicates the agent has been discharged.

INITIAL AGENTInitial Agent

Yellow in colour. Lit when the initial agent activation circuit is selected.

RESERVE AGENTReserve Agent

Yellow in colour. Lit when the reserve agent activation circuit is selected.

BLOCKED MODEBlocked Mode

Yellow in colour. Lit when the lock-off valve has been activated.

MANUAL HOLDManual Hold

Yellow in colour. Lit when a Hold button is depressed on an LCS.

TRIGGER ZONE

DISABLED Trigger Zone DisabledYellow in colour. Lit when any of the trigger zones on the FACP are disabled.

COMMON FAULTCommon Fault

Yellow in colour. Lit under pressure switch, low pressure switch, lock-off valve, activation circuit,stage 1 output, stage 2 output, Local Control Station, trigger zone(s) fault conditions.

AUTO / MANUALAuto/Manual

Yellow in colour. Lit when a release sequence can be started automatically or manually.

MANUAL ONLY

Manual OnlyGreen in colour. Lit when a release sequence can be started manually only.

DISABLEDDisabled

Yellow in colour. Lit when the release sequence can not be started automatically or manually.

BuzzerBuzzer is activated under programmed control.


19/28


Page: 17

Local Control Station Terminal Blocks TB1 & TB2

TB2 Terminal Assignment TB1 Terminal Assignment1 RS485 + In 1 +27V In2 RS485 - In 2 0V In3 RS485 Common 3 +27V Out

4 RS485 + Out 4 0V Out5 RS485 - Out6 RS485 Common7 Interlock+8 Interlock-


Local Control Station Layout

The Comms line is RS485 between the Local Control Station and the Termination Board.

The Interlock is a monitored input with 10K EOL used to determine if air conditioning dampersand doors are closed. Typically the agent is not discharged until all dampers / doors are closed.

D10

D9

D14

D13

D12

D11

D6

D5

D4

D3

D8

D7

U4

U1

U2

U3

X1

Manual ReleaseActivated

Initial Agent

Manual Hold

Auto / Manual

Auto ReleaseActivated

Reserve Agent

Trigger ZoneDisabled

Manual Only

AgentReleased

Blocked Mode

Common Fault

Disabled

Hold

CutoutCutout

RS 485OUT

TB2

TB1

SW 2

K1

HY1

CN5

BUZZERBZ1

INTERLOCK

CO M TerminationLink

AddressSwitch

EC3AW3V3 POWERSUPPLY

+

CO M

+27V

Out 0V

+27VIn

0V

+_

+_

RS 485IN

+_

+

+

1

2

3

4

O

N

CN 8 CN 2

Key Switch

Manual ReleaseCutoutCutout

Figure 24: Top PCB Layout Figure 25: Bottom PCB Layout

5.5 Agent Release Termination Board BRD25ATB

Figure 26: Agent Termination Board PCB Layout

LK1

Q2

SW 1

U5

U9 U7

U1

RL6

RL4RL1 RL2 RL5 RL3

CN5

U3U4 U2

U10

RL7

+ LOCK-

+ L.PSW-

RELEASE

C

NC NO///

+L

COMM

NC

NO

-L

C

NC NO///

-+

SIG+

SIG-

LCP CABLE

+ PSW -

MonitoredINPUTS

N/0

STAGE2GASFIRED

+ - N/0 COMN/0 COM +

SYST.INOP.

SCRN+24VDC + -

C

NC NO///

C

NC NO///

-L

NO

NC

COMM

+L-L

NO

NC

COMM

+L

0VDC+ -

STAGE1

-COM

TB7TB6TB5TB4TB3TB2TB1

CN2

CN1

Address SettingCN 3 CN427V In

27V toNext Board

RS485 ControlIn From CN2 ofPrevious Board

RS485 ControlOut to NextBoard or Link 1EOL is Applied

MAIN RESV

+ - Outputs are Monitored

ContactRating

1A & 24V

ContactRating

1A & 24V

ContactRating

1A & 24V

ContactRating

1A & 24V

1 2 3 4

ON

EOLTermination

Quiescent Current:12mA

4K7

22KEOL

10KEOL

10KEOL

10KEOL


20/28


Page: 18

The Agent Release Termination Board interfaces to the;

1. The FACP via CN1, CN2 continuing the RS485 communications bus if required. LK1 isinserted if this is the last backpan board on the bus.

2. LCSs ( up to 4 ) via TB1. LK1 is inserted in the last board in the RS485 Bus

3. Monitored Inputs: via TB2. ( EOL Resistance 22K, Series Resistance 4K7 )(a) Pressure Switch ( PSW ) agent released(b) Low Pressure Switch ( LPSW ) agent storage cylinder pressure has dropped to a pre-

determined level; and(c) Interlock, the manual lock-off valve has been operated.

4. Gas Fired: Output via RL2 N/O contacts rated at 1A @ 24VDC wired to TB3. Used toindicate to other monitoring devices the agent has been released.

5. System Inoperative: via RL1 N/O contacts rated at 1A @ 24VDC wired to TB4. Used towarn by way of signage / audible alarm and/or monitoring that the system is inoperative.

6. Stage 1: Output; initiates the visual and audible Fire Alarm and Evacuate warnings.

(a) Monitored; via RL4 C/O contacts wired to TB5 1 & 2 ( EOL required 10K ) and(b) un-monitored; via RL5 N/O contacts wired to TB5 3 & 4.

7. Stage 2: output; initiates the visual and audible Fire Alarm and Do No Enter warnings

(a) Monitored; via RL6 C/O contacts wired to TB6 1 &2; ( EOL required is 10K ) and(b) Un-monitored; via RL3 N/O contacts wired to TB6 3 & 4

8. Release: Main actuating circuit, monitored (10K EOL required) via TB7 1 & 2 ( 2A currentlimited ),Release: Reserve actuating circuit, monitored (10K EOL required) via TB7 3 & 4 ( 2Acurrent limited )(a) To Pyrogen Igniter ( max of 10 )

(b) Metron Igniters ( max of 10 a series 2watt 18 resister must be added to the circuit )(c) Solenoid valve ( max current of 2 amps & 27VDC )

5.6 Interface Wiring

Monitored Inputs TB2 1 & 2Pyrogen,

This input relies on a thermal fuse used in conjunction with 22K EOL and 4K7series resistors. The type of agent release mechanism has to be set in theProgramming Menu for the input to function as per the manufacturers specificationsand be in accordance with the relevant Standard.

1 2

PSW

TB2Termination Board

4K7 22KEOL

PyrogenCanister

+ -

PyrogenReleasePoint

FUSE

Pyrogen Release

Brd. 302-740 To TB7MAIN or

RESERVERelease

MAIN / RESERVERELEASE

TB1

-VE

+VE

17/10/00

D1

R1

C1

C2

R2

TB2

302-7400

Figure 27: Pyrogen Wiring


21/28


Page: 19

Solenoid & Metron

This input relies on N/O or N/C relay contacts used in conjunction with 22K EOL and 4K7series resistors. The type of agent release mechanism and contacts used has to be set in theProgramming Menu for the input to function as per the manufacturers specifications and be inaccordance with the relevant Standard.

Note: The PSW, LPSW & the Interlock Mechanisms are allmounted onto the top of the cylinder containing the Agent

TerminationBoard

+ -

4K722KEOL

AgentDistribution

4K7

22K EOL

LPSW LOCK

4K7

22K EOL

PSW

+ - + -

MAIN / RESERVERELEASE

To TB7MAIN or

RESERVERelease

Agent

Figure 28: Solenoid, Metron PSW, LPSW and LOCK Wiring

LPSW & LockThese inputs are also monitored and should be wired as shown above

1

2

To MonitoringInterface / Device

0V

RL2ATB3

= MOV35V

*

* *

To SysInop Mon

+

-System Inoperative

1

20V

RL1ATB4

+27V CurrentLimited to1A

Figure 29: Gas Fired Wiring Figure 30: System Inoperative Wiring

As can be seen from above the;

Gas Fired Output can be wired to any interfacing or 1A monitoring circuit that requires a closedrelay contact to indicate a change of state. This could be a relay or a solid state device.

System Inoperative Outputs 27V @ 1A to supply interfacing, signage and aural alarms toindicate the system has been taken out of service or has developed a fault.

Stage 1, Stage 2

- ( + )

+ ( - )

*

0VTB5 = Stage 1TB6 = Stage 2

= MOV35V

*

*

+ve

-ve 10KEOL

1 or 2 WaySignage

To audible / visual

device or interface

*

Stage 1 or Stage 2

RL3ARL5A

RL4B

RL4A RL6A

Agent Termination Board Relays

RL6B

1

2

3

4

The above circuitry applies to bothTB5 ( Stage 1 ) and TB6 ( Stage 2 )

TB5 / 6

MAIN RESV

+ -

10K EOL

Solenoid

+ -

TB7

Figure 31: Stage 1 and 2 Wiring Figure 32: Agent ReleaseSolenoid Wiring

Current Generation SignageStage 1 displays the warning sequence ie discharge of the agent is imminent while Stage 2communicates the discharge of the agent is or has occurred DO NOT ENTER.

2nd

Generation SignageIs able to display both phases of agent release.


22/28


Page: 20

6 Appendix: Adding to the System Menu & Programming

In this example 1 Input Board, 1 Relay Board and 1 Sounder Board will be added to the system. TheDisplay and Zone Labels will then be edited.

Step 1:Go to the SYSTEM MENU and then follow the procedure as set out below.

ALARMYES / NO

RESOUND

YES / NOBUZZERSYSTEM

EARTH MONYES / NO

BRIGADENO

FIRE FANNO

RELAYSYES

AGENTNO

SOUNDERSYES

SW INDICNO

INDICATENO

INPUTSYES

MIMIC0 TO 8

CODEAS4428

MENU

ENTER

LEGEND:

PRESS ENTER TO ACCESSMENU AND UPDATE PROGRAMOR CHANGE MENU

PRESS MOVE FORWARDTHROUGH THE MENU

PRESS: MOVE FORWARDOR BACKWARDTHROUGH THE MENU

CANCELPRESS CANCEL ATANY TIME TO BACKOUT OF THE MENU

MENU

ENTERMENU

ENTER

MENU

ENTER

CANCEL

MENU

ENTER

PRESS THESE KEYSTO SET YES / NO

YES

MENU

ENTERUPDATE PROGRAM

FACTORY SETCAN NOT BECHANGED

EXAMPLESET RESOUND TO YESTHEN MOVE TO ALARM

MOVE TO ALARMYES / NO

IF THESE 4OPTIONSARE NOT SETTO YES THEYWILL NOTAPPEARIN THETEST MENU

ENTERPASSWORD

FACTORY DEFAULTPASSWORD IS 3333

PASSWORD0000

MENU

ENTER

PASSWORD0100

PASSWORD0120

PASSWORD0123

MENU

ENTER

PASSWORDACCEPTED

EXAMPLESETTING

PASSWORD0123

SYSTEM

EXAMPLE OF SETTINGTHE SYSTEM MENU IF A

RELAY BOARD IS INSTALLED

YESMENU

ENTERUPDATE PROGRAM

EXAMPLE OF SETTINGTHE SYSTEM MENU IF A

SOUNDER BOARDIS INSTALLED

YESMENU

ENTERUPDATE PROGRAM

NO BRIGADE INTERFACE BOARD INSTALLED

NO FIRE FAN MODULE INSTALLED

NO AGENT RELEASE MODULE INSTALLED

NO SWITCH & INDICATOR CARD INSTALLED

NO INDICATOR CARD INSTALLED

NO MIMIC INSTALLED

EXAMPLE OF SETTINGTHE SYSTEM MENU IF AN

INPUT BOARD IS INSTALLED

YESMENU

ENTERUPDATE PROGRAM

Example of Adding Input, Relay and Sounder Boards in the SYSTEM MEU


23/28


Page: 21

Step 2

ZONES

CLOCK

OUTPUTS

FIRE FAN

AGENT

SOUNDERS

DISPLAY########

SET SNDRBRD O/P

.2..5..8

Z LABELS

MENU

ENTER

LEGEND:

PRESS ENTER TO GO TO SUB MENU, SET MENU OR UPDATE PROGRAM

PRESS MOVE FORWARD THROUGH THE MENU

PRESS MOVE FORWARD / BACKWARD THROUGH THE MENU

CANCEL PRESS CANCEL AT ANY TIME TO BACK OUT OF THE MENU

MENU

ENTER

CANCEL

MENU

ENTER

ACFISOALTE

ACF

ISOALTE PRESS ACF TO ISOL ATE CIRCUITS EXTERNAL TO FACP

MENU

ENTER

EDITTEXT

SET ZONETO

ACTIVATE1...5..8

MENU

ENTER

PROGRAM

MENU

ENTER

MCP ZONEZ#

1 TO 8

ON

OF F

1 TO 8

IN THIS EXAMPLE SNDR O/P 2,5&8ARE ACTIVATED BY ZONES 1,5&8

RELAYSR3 Z-ALRM

1..4...8

R3 SWITCH.......

R3 Z-FLT.......

R3 Z-ISOL.......

R3 I/P1.3...7.

MENU

ENTERRELAY 3 MENU

ENTER

SELECT RELAY 3

ON

OF F

MENU

ENTER UPDATE MENUMENU

ENTER

IN THIS EXAMPLE RELAY 3 IS ACTIVATED BY ZONES 1,4 OR 8WHEN IN ALARM OR I/P's 1,3 OR 7 OF THE I/P BOARD ARE ON

TURN OFF2,3,5,6,7

TURN ON1,3&7

ON

OFF

MENU

ENTER UPDATE MENUMENU

ENTER

TO EDIT DISPLAYTEXT USE

SELECTZONEMENU

ENTER

TO MOVE THROUGH THE

ALPHABET / NUMBERS

TO MOVE THROUGH

THE WORD

MENU

ENTER

EDITTEXT

UPDATE MENUMENU

ENTER

Programming the Relays and Sounders to be Activated by Zones and Editing Text

CN 5

CN10

CN 1

CN 3

CN 2

CN 4

Address SW

1 2 3 4

ON

Set to 1

EOL Not Used

RELAY BOARDMAIN CARD

CN 1

CN 3

CN 2

CN 4

Address SW

1 2 3 4

ON

Set to 1

EOL Not Used

INPUT BOARD

CN 1

CN 2

TB3

Address SW

1 2 3 4

ON

Set to 1

EOL LINKINSERTEDIN LASTBOARD OFTHE CHAIN

SOUNDERBOARD

+-

+++++-----

RS485 and 27V Cabling for the Installation of a Relay, Input and Sounder Board as in the SYSTEM and

PROGRAMMING Menu Structures Above


24/28


Page: 22

7 Status and Programming Screens

The following shows all the screens that are possible in the FACP and how to navigate throughthem. I f a screen is not available it means that option has not been installed or is not available tothe model in use.

Operating Main Menu

LEVEL 1 LEVEL 2 LEVEL 3

STATUS FAULTS TEST DISABLE SYSTEM PROGRAMMING

7.1 Level 1 to 3 Status Screens

SOFTWAREVER E1.2

STATUS

OUTPUTS BRIGADE RELAYS FIRE FAN AGENT SOUNDERS INPUT VOLTAGE

ALARM 1OFF/NORM

ALARM 2OFF/NORM

ALARM 3OFF/NORM

ALARM 4OFF/NORM

FIREOFF/NORM

FAULTOFF/NORM

ANC OUTOFF/NORM

ALARM 1OFF / ON

FAULTOFF / ON

DISABLEOFF / ON

BATT FAILOFF / ON

ALARM 2OFF / ON

RELAY 1OFF / ON

RELAY 2OFF / ON

RELAY 3OFF / ON

RELAY 4OFF / ON

RELAY 5OFF / ON

RELAY 6OFF / ON

RELAY 7OFF / ON

RELAY 8OFF / ON

FAN 1OFF / ON

FAN 2OFF / ON

FAN 3OFF / ON

FAN 4OFF / ON

AGENTOFF/NORM

SNDR 1OFF/NORM

SNDR 2OFF/NORM

SNDR 3OFF/NORM

SNDR 4OFF/NORM

SNDR 5OFF/NORM

SNDR 6OFF/NORM

SNDR 7OFF/NORM

SNDR 8OFF/NORM

INPUT 1OFF / ON

INPUT 2OFF / ON

INPUT 3OFF / ON

INPUT 4OFF / ON

INPUT 5OFF / ON

INPUT 6OFF / ON

INPUT 7OFF / ON

INPUT 8OFF / ON

BATT V26.8V

CHRGR V27.0V

SYSTEM V27.0V

MENU

ENTER

MENU

ENTER

MENU

ENTER

MENU

ENTER

MENU

ENTERMENU

ENTERMENU

ENTER

MENU

ENTERMENU

ENTER

MENU

ENTER

LEGEND:PRESS ENTER




CANCEL

MENU

ENTER

PRESS THESE KEYSTO SET YES / NO, OFF / ON,OFF NORMAL


25/28


Page: 23

7.2 Level 3 System Programming

ALARMYES / NO

RESOUND

YES / NOBUZZERSYSTEM

EARTH MONYES / NO

BRIGADEYES / NO

FIRE FANYES / NO

RELAYSYES/ NO

AGENTYES / NO

SOUNDERSYES / NO

SW INDICYES / NO

INDICATEYES / NO

INPUTSYES / NO

MIMIC0 TO 8

CODEEN54

MENU

ENTER

LEGEND:

PRESS ENTER TO ACCESSMENU AND UPDATE PROGRAMOR CHANGE MENU




MENU

ENTERMENU

ENTER

MENU

ENTER

CANCEL

MENU

ENTER

PRESS THESE KEYSTO SET YES / NO

YES

MENU

ENTERUPDATE PROGRAM

FACTORY SETCAN NOT BECHANGED

EXAMPLESET RESOUND TO YESTHEN MOVE TO ALARM

MOVE TO ALARMYES / NO

NOTES:TO ADD OR DELTEFROM THE SYSTEM SETTO YES OR NO AND THEN

GO TO THE PROGRAMMENU TO SET THEOPERATIONALPARAMETERSIF THESE OPTIONSARE NOT SET TO YESTHEY WILL NOT APPEARIN THE TEST, STATUS ORPROGRAM MENU

ENTERPASSWORD

FACTORY DEFAULTPASSWORD IS 3333

PASSWORD0000

MENU

ENTER

PASSWORD0100

PASSWORD0120

PASSWORD0123

MENU

ENTER

PASSWORDACCEPTED

EXAMPLE OFSETTING

PASSWORD0123

SYSTEM


26/28


27/28


28/28


UNCONTROLLED DOCUMENT

NOTE: Due to Ampacs commitment to continuous improvement specifications may change without notice.

AUSTRALIAAMPAC TECHNOLOGIES PTY LTD

97 Walters DriveOsborne Park 6017Western Australia

Tel: 61 8 9242 3333Fax: 61 8 9242 3334

Email: [email protected]

EUROPEAMPAC EUROPE LTD.

Unit 1, Norden Court,Alan Ramsbottom Way

Great Harwood, BlackburnEngland BB6 7UR

Tel: 44 (0) 1254 880 201Fax: 44 (0) 1254 880 202Email: [email protected]

NEW ZEALANDAMPAC INDUSTRIES LTD.

Unit 4 101 Diana DriveGlenfield, Auckland

New Zealand

Tel: 64 9 443 8072Fax: 64 9 443 8073

Email: [email protected]

man2512 zonesense plus en add ons inst comm

Documents