1

MainMenu Screens Guide Version: 1.3

2

Table of content: Introduction Main Screen

o dbdatmcmd (load, clear fitnes, clear status, ...) o ATM Info (port, connection, termid, location, ...) o ATM Financial Transactions (Count, Total,...)

dbdatmcmd Screen

o Show Status o Clear Status all o Clear Fitness all o Mark Idle o Load all o Load Key o Load MAC

ATM Info Screen

o Check ATM's connection o Check ATM's port status o Search for ATM by TERMID o Search for ATM by LOCATION

ATM Financial Screen

o Cash Withdrawal and B.inquiry (Total) o Reversal Transactions (Total) o Rejected Transactions (Total) o Get all transactions of ATM for specific date o Get all transactions of ATM between dates

3

Introduction

MainMenu is menu-based tool where lots of Oasis command groups together to facilitate using the system without need technical background. MainMenu mainly help Monitoring Team accomplished their tasks with some switch-side interactivity.

4

Main Screen

As shown above, the main screen displays the three root type of commands that can be handled by MainMenu:

1. dbdatmcmd (load, clear fitnes, clear status, ...) Do all commands related to ATM for checking its status and preparing for load.

2. ATM Info (port, connection, termid, location, ...) Check ATM’s connection and status of the port, also provide tools for searching ATM by termed, and location.

3. ATM Financial Transactions (Count, Total,...) Display ATM’s transaction on different criteria.

4. Exit Stop and exit the tool.

5

dbdatmcmd Screen

The basic commands to LOAD ATM is just here, ordered by the way exact happened by Switch Administrator:

1. Show Status Display the current status of a given ATM

ATM number should be entered as shown above with 3 digits only and not accepted if it’s lower or higher!

6

Status will be displayed followed by “Press any key to continue” that lead to re-enter your choice again.

2. Clear Status all Send “clear status all” command so that any stored wrong status from ATM would be cleared waiting for loading.

ATM number should be entered as shown above with 3 digits only and not accepted if it’s lower or higher! No output from this command except statement “Clear Status all sent to” followed by ATM full name.

3. Clear fitness all Same as “Clear Status All” send clear fitness command to ATM that prepare for loading.

7

4. Mark Idle This command used usually in case ATM doesn’t accept loading for many times.

Sometimes a command hangs in ATM buffer that can’t accept any other commands, Mark idle clear that to allow commands accepted.

5. Load all Send “load all” commands to ATM. No return status from this command currently available in this release, hope to provide that soon.

As shown, ATM number should entered with 3 digits only, and statement “Load all sent to” followed by ATM full name displayed to inform users with sending successfulness, just sending the command and not “going in service” actually.!

8

6. Load Key Used usually when “key failed” in loading process.

No output yet available from the command except a statement “Load key sent to” followed by full ATM name.

7. Load MAC Special command used rarely to re-generate key authentications between ATM and switch.

Also with no output yet.

8. Back Go back to Main Screen.

9

ATM Info Screen:

Display the basic information for ATM:

1. Check ATM's connection Check connection of both Router’s line, and ATM’s line, and write down the IP for them

2. Check ATM's port status Check port’s status and readiness of ATM to accept commands.

10

3. Search for ATM by TERMID Write down any digits of Termid and get the results

4. Search for ATM by LOCATION Write down any characters of location and get the results

11

5. ATM Financial Screen

Provide financial queries for ATM on different criteria:

1. Cash Withdrawal and B.inquiry (Total)

On specific dates and times, display total number of transactions and sum of its amount, also how many balance inquiry had done. It requires ATM unit number –which is 3 digits- and both start, end dates and start, end times.

12

2. Reversal Transactions (Total)

On specific dates and times, display total number of reversal transactions and sum of its amount.

3. Rejected Transactions (Total)

On specific dates and times, display all rejected txn ordered by reason code.

13

4. Get all transactions of ATM for specific date

For only one day, all transactions that had been done.

5. Get all transactions of ATM between dates

Between two dates, all transactions that had been done.