lux back to wall pan...kado lux back to wall pan specifications recommended use domestic, hotel and...
TRANSCRIPT
KADO LUX BACK TO WALL PAN
SPECIFICATIONSRecommended Use Domestic, Hotel and Commercial
Material Vitreous china
Colour White
Weight Pan: 28kg
Seat Soft close quick release toilet seat
Soft close quick release thin toilet seat
Rim Configuration Box Rim
Bowl Configuration Universal S & P
Set Out S Trap: 95-105mm
Pan Fixing Screwed to floor (Fixing Screws supplied)
CLEANING RECOMMENDATIONSWe recommend the use of soapy water or approved bathroom cleaners.
This bathroom product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.
To see the complete KADO range go to www.reece.com.au/bathrooms
Dimensions are nominal measurements only
100
180
360
545
245
95-105
370 320180
30
65
TM
WMKA21192AS 1172.1
page 1 of 4
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 3
The more stars the more water efficient
WATER RATINGwww.waterrating.gov.au
In accordance with AS/NZS 6400
Licence No. 0025Reece Limited
4.5 L per full flush / 3 L per half flush
3.5 litres average flush
KADOLUX BACK TO WALL PAN
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
INSTALLATION INSTRUCTIONS
A
100mm
180mm
Position pan against wall and mark off pan fixing holes on floor. Water inlet pipe should be roughed in at 320mm. Cut inlet pipeso that 100mm protrudes from finished wall and attach seal.
320mm
Fixing bracket & Water inlet
Insert waste pipe in to f loor a t a se tout o f 95-105 and180mm abovefinished floor and fix bracket into position as per diagram above.
Push pan into position. Ensure that you make a firm connection with inlet andoutlet pipes and avoid disturbing the floor fixing brackets. Flush test for leaks.
180mm
180mm
S-Trap Installation NOTE: This is a set out of 95-105mm
100mm DWV with pan collar (not supplied). Push pan back into position. Ensure that you make a firm connection with inlet and outlet pipesand avoid disturbing the floor fixing brackets. Flush test for leaks.
180mm
P-Trap Installation
Ensure that pan is level. Fix pan to floor using fixing screws and flexible sealant. Install soft closing seat.
sealant
Fixing Pan to Floor
95-105
page 2 of 4
KADOLUX BACK TO WALL PAN
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
LUX THIN SEAT INSTALLATION INSTRUCTIONS
A
Warning:Using an abrasive cleaner (such as a toilet bowl cleaner) on the seat, seat cover, hinges or hinge covers can cause damage. If any of these components come into contact with such a cleaner, use a damp rag or sponge to wipe off immediately.
CLICK
CLICK
1
2
3
1 2 3
B1
2
0
0 1m
m≈
A
1
2
360˚
3.1
3.1 3.2
3.2
Cleaning
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
INSTALLATION INSTRUCTIONS
C
D
FE
B (x2)
C (x2)
D (x2)
F (x2)
E (x2)
Important Note:Soft close seat and covers can take up to 30 seconds to close. Do not force the closing mechanism as this may result in damage. The fixings of your seat may require re-tightening occasionally depending on use.
Installation
Warning:
1 2 3
1
2
3.1
3.1 3.2
3.2
Cleaning
Picture Reece Code Product Description Part Number
9506341 KADO LUX THIN SEAT BUFFER SET I9037-RPC1
9506342 KADO LUX THIN SEAT HINGE SET I9038-RPC1
SPARE PARTS
page 3 of 4
KADOLUX BACK TO WALL PAN
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
LUX SEAT INSTALLATION INSTRUCTIONS
Top Fixing Installation procedure.1. Insert the nylon toggles into the hinge holes of the pan.2. Mount the hinges onto the shaft of the toilet seat.3. Plug the bolt into the nylon toggle.4. Align the toilet seat with the pan.5. Tighten the screws.6. Push the button to release the seat.7. Lift the toilet seat.8. Insert hinge covers over posts.9. Fix seat into final position.
Important Note:Soft close seat and covers can take up to 30 seconds to close. Do not force the closing mechanism as this may result in damage. The fixings of your seat may require re-tightening occasionally depending on use.
Picture Reece Code Product Description
9506723 KADO QUICK RELEASE SCS BUFFER SET
9503294 TOP FIX QUICK RELEASE HINGE SET
SPARE PARTS
page 4 of 4