LUMITray TechnologyFull-arch LUMINEERS Placement Technology

2

1st visit

IMPRESSIONS

PHOTOGRAPHS

scan produce3D design

DESIGN & PRODUCTION

Process Overview

3

Digital CAD/CAP Software● LUMITray uses state-of-the-art

technology that facilitates digital design and fabrication for beautifully precise veneers.

● With this technology, technicians build the veneers – to micron accurate specifications – directly on a digital 3-D model.

● This process creates a superior fit at the gingival margin, which means less finishing.

4

Digital Preview

● Because the system is digital, you can preview, change and accept the restoration from your dental office before it’s fabricated, ensuring that final restorations are to exact specifications.

5

Digital Preview

6

Without Reshaping Before Impression

With Reshaping BeforeImpression

7

LUMIKey Reshaping Guides

● If reshaping is requested, you will receive a LUMIKey reshaping guide, which is created using the same digital specifications of the restoration.

● The LUMIKey simplifies the placement process and produces accurate results.

8

LUMIGuard● Is your LUMITray patient a bruxer?

LUMIGuard is the answer.

● LUMIGuard is an occlusal protection plate that can be worn during the day or night.

● The custom fit and minimalistic design of LUMIGuard means you can provide comfortable protection for your patients’ perfect new smiles.

● Available at the time of placement of the LUMINEERS with LUMITray.

Placement Procedure

LUMITray: Step-by-Step

10

Step 1Step 1: Reshaping Trays

11

Step 2

● Break the glaze of the enamel– Take medium coarse or fine diamond and

roughen the outer surface of the enamel• Draw the diamond across the incisal edge

at a 45-degree angle (This allows for a more full seating of the LUMINEERS and increases mechanical retention)

12

Step 2

● Lightly roughen the facials of all teeth to receive Lumineers

● Be thorough and methodical

13

Step 3

Etching

●Etch the teeth withEtch ‘N’ Seal for 20 seconds●Rinse thoroughly with water

14

Step 5

Bonding●Add 5 coats of TenureA + B●Add 1 coat of Tenure S●Tooth surfaces must be shiny

15

Step 6Prime-Bonding on LUMINEERS● These come pre-etched, pre-

hydrolyzed andpre-silanated

● Add 1 coat of Tenure A + B on the inner side of the LUMINEERS

● Add 1 coat of Tenure S on the inner side of the LUMINEERS

16

Ultra-Bond Plus on LUMINEERS

●Add a layer of Ultra-Bond Plus resin cement to the inner side of the LUMINEERS. Work upwards from incisal edge of the LUMINEERS to gingival edge and keep contact with the LUMINEERS (see diagram)

Step 7

17

Step 8

Insert the LUMITray

●Remove the Paint-On Dental Dam or interdental strips! ●Center the LUMITray (midline)●Insert the tray in one smooth movement. Apply a light, continuous, buccal pressure. Take your time for the placement.●Remove excess Ultra-Bond cement at the gingiva with microbrush

18

Step 9

● Set the Sapphire Plus Light for 3 seconds

● Tack-cure with a sweeping movement of the 9mm tip

● With a probe remove more excess cement

● Light-cure each tooth 3 seconds through tray with Sapphire Plus

19

Step 10

Remove LUMITray

●Remove the LUMITray (don’t twist)

●Remove the retentions with Schure 349

●Remove any excess on the lingual side of the teeth with Schure 349

20

Step 11

Open Interdental Spaces

●Remove Ultra-Bond Plus cement from interproximal spaces with a CeriSaw●Maintain complete control over the instrument. If difficult, postpone to follow-up visit.

21

Step 12

Light-Cure the LUMINEERS

●Cure each LUMINEERS individually for a second time on both the lingual and buccal sides for 5 seconds with the Sapphire Plus Light

22

Step 13

Check Occlusion and Polish

●Check and finish the occlusion

●Polish the LUMINEERS with Porcelain Polishing Paste

23

Thick Blue Paper Makes Contact Areas Obvious

Note: cuspal inclines; adjust areas inside circles

Note: vertical stops, cusp tips and fossa

24

Step 14

Final Check

●Take after photos●Give the patient their LUMIGuard

25

Before and After