louver products - · pdf filepage header 2 louver selection guide louvers airflow aesthetics...
TRANSCRIPT
Page Header
222222
Louver Selection Guide
Louvers Airflow Aesthetics AMCA Certifications
Type ModelFree Area48 x 48 in.
(sq. ft.)
Free Area48 x 48 in.
(%)
Depth(in.)
Blade Alignment
Blade Angles
(degrees)
Wind-Driven Rain
Water Penetration
Air Performance
Sound
Drainable Blade
EDD-401 8.22 51 4 H 37/45
EDD-601 8.21 54 6 H 37/45
EHM-601 7.91 49 6 H 37/45
ESD-202 6.01 38 2 H 37/45
ESD-403 8.00 50 4 H 37/45
ESD-435 8.98 56 4 H 37.5
ESD-603 8.36 52 6 H 37/45
ESD-635 9.41 59 6 H 37.5
DrainableHead
EDJ-202 6.01 38 2 H 45
EDJ-401 8.32 52 4 H 37/45
EDJ-430 8.35 45 4 H 30
EDJ-601 8.69 54 6 H 37/45
EDK-402 8.49 53 4 H 37/45
EDK-430 8.80 55 4 H 30
EDK-602 8.35 52 6 H 37/45
ESID-430
DISCHARGE7.66 48 4 H 30
ESID-430 INTAKE 10.88 68 4 H 30
Non-Drainable
ESJ-202 6.01 38 2 H 45
ESJ-401 8.44 53 4 H 37/45
ESJ-602 8.73 55 6 H 37/45
ESK-402 8.45 53 4 H 37/45
ESK-602 8.46 56 6 H 37/45
Recessed Mullion
ESJ-401RM 8.58 54 4 H 37/45
ESJ-602RM 8.38 52 6 H 37/45
ESK-402RM 8.42 53 4 H 37/45
ESK-602RM 8.13 51 6 H 37/45
Adjustable Blade
EAD-401 6.54 41 4 H 45
EAD-601 7.34 46 6 H 45
EAD-635 8.73 55 6 H 35
EADC-401 5.84 37 4 H 45
EADC-601 6.44 40 6 H 45
EAH-401 6.48 41 4 H 45
EAH-690
(45º BLADE)6.32 40 6 H 45
EAH-690
(90º BLADE)10.87 70 6 H 90
Combination Louver/Damper
EAC-401 6.34 40 4 H 45
EAC-601 7.41 46 6 H 45
EACA-601 7.68 48 6 H 45
EACC-401 5.59 35 4 H 45
EACC-601 6.20 39 6 H 45
EACN-601 7.18 45 6 H 45
ECD-401 7.60 46 4 H 37/45
ECD-601 7.32 48 6 H 37/45
GCE-202 4.96 31 2 H 45
GCE-402 6.36 40 4 H 45
GCI-202 5.26 33 2 H 45
GCI-402 6.39 40 4 H 45
Page Header
33333
Louvers Airflow Aesthetics AMCA Certifications
Type ModelFree Area48 x 48 in.
(sq. ft.)
Free Area48 x 48 in.
(%)
Depth(in.)
Blade Alignment
Blade Angles
(degrees)
Wind-Driven Rain
Water Penetration
Air Performance
Sound
Sightproof
SED-202 3.42 21 2 H NA
SED-401 5.16 32 4 H NA
SED-501 9.11 57 5 H NA
SEH-202 3.73 23 2 H NA
SEH-401 5.16 32 4 H NA
SES-202 3.75 24 2 H NA
SES-401 5.33 33 4 H NA
SEV-401 5.33 33 4 V NA
SEV-501 9.11 57 5 V NA
Wind-Driven Rain
EHH-201 6.20 39 2 H NA
EHH-401 6.72 42 4 H NA
EHH-501 6.80 43 5 H NA
EHH-601 7.58 47 6 H NA
EHH-701 6.99 43 7 H NA
EVH-201 5.71 36 2 V NA
EVH-401 6.38 40 4 V NA
EVH-602 5.88 39 6 V NA
EVH-801 5.05 32 8 V NA
Florida Product
Approved
AFJ-601X 4.89 31 6 H 45
EHH-501X 6.80 43 5 H NA
ESD-435X 8.98 56 4 H 37.5
ESD-635X 9.41 59 6 H 37.5
EVH-602X 5.88 37 6 V NA
Miami-Dade Qualified
EACA-601D 7.21 45 6 H 45
EHH-601D* 7.58 47 6 H NA
ESD-635D* 9.41 59 6 H 37/45
ESS-502D 8.19 51 5 H NA
EVH-602D* 5.88 37 6 V NA
EVH-660D 7.29 45 6 V NA
Thinline
ESF-145 6.08 38 1.5 H 45
ESJ-150 7.29 46 1.5 H 30.5
ESU-130 10.95 68 1.5 H 30
ESU-130S 10.95 68 1.375 H 30
ESU-150 7.40 46 1.5 H 52
ESU-150S 7.70 48 1.375 H 52
Acoustical
AFA-801 5.21 33 8 H 45
AFJ-120 3.67 23 12 H 45
AFJ-601 4.89 31 6 H 45
AFJ-801 4.28 27 8 H 45
AFS-120 4.27 27 12 H 45
Fabricated
FAD-402 5.98 38 4 H 45
FAD-602 7.11 45 6 H 45
FAD-635 8.77 55 6 H 35
FAJ-402 5.93 37 4 H 45
FAJ-602 6.23 39 6 H 45
FDS-402 7.03 44 4 H 45
FDS-602 8.15 51 6 H 45
FSJ-402 7.55 47 4 H 45
FSJ-602 7.57 47 6 H 45
*Optional factory installed VCD-40 control damper **Optional factory installed HCD-240 heavy duty damper
Louver Selection Guide
3
Page Header
4
Drainable Blade
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
EDD-401 4 DD 0.081 0.081 8.22 51 992 0.143 8154 8312
EDD-601 6 DD 0.081 0.081 8.21 52 1107 0.204 9088 8399
EHM-601 6 DD 0.081 0.081 7.91 49 1065 0.166 8424 6577
ESD-202 2 D 0.063 0.063 6.01 38 1058 0.141 6359 5963
ESD-403 4 D 0.081 0.081 8.00 50 1007 0.176 8056 8188
ESD-435 4 D 0.081 0.081 8.98 56 1151 0.213 10336 9285
ESD-603 6 D 0.081 0.081 8.36 52 1027 0.178 8586 8359
ESD-635 6 D 0.081 0.081 9.41 59 1077 0.173 10135 9956
* Test size: 48 x 48 in. unit @ 15 min. duration D = Drainable DD = Dual Drainable
Dual Drainable Blades
Drainable Head
Sloped Sill
EDD-401
• Drainable blades offer excellent resistance to water penetration.
• Drain gutters located on every blade to capture water.
• Integral downspouts located within the jambs to channel water downward to sloped sill for drainage away from the louver.
• EDD Series incorporates dual drainable blades for additional water capture.
• EHM Series incorporates recessed mullion design for continuous blade appearance for multiwidth sections.
• Models ESD-435 and ESD-635 lend 56% and 59% free area respectfully.
Dual Drainable Blades
Flat Head
Flat Sill
Drainable Head
Sill Pan
EHM-601
Recessed Mullion
ESD-403
Drainable
Blades
Drainable
Head
Sloped
SillESD 403SSEEEEEE ESD-635ESD-435
Drainable
Blades
Drainable
Head
Sloped
Sill
Drainable
Blades
Drainable
Head
Sloped
Sill
Page Header
5
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
EDJ-202 2 J 0.063 0.063 6.01 38 869 0.105 5223 5947
EDJ-401 4 J 0.081 0.081 8.32 52 963 0.151 8012 8325
EDJ-430 4 J 0.081 0.081 8.35 45 941 0.105 7857 7849
EDJ-601 6 J 0.081 0.081 8.69 54 998 0.166 8673 8563
EDK-402 4 K 0.081 0.081 8.49 53 934 0.145 7930 8219
EDK-430 4 K 0.081 0.081 8.80 55 1002 0.142 8818 9309
EDK-602 6 K 0.081 0.081 8.35 52 1097 0.198 9160 8426
ESID-430
(Intake)4 K 0.081 0.081 7.66 48 - 0.062 4979 -
ESID-430
(Discharge)4 DC 0.081 0.081 10.88 68 - - - 13056
* Test size: 48 x 48 in. unit @ 15 min. duration J = J Style K = K Style DC = Discharge
Drainable Head
EDJ-401
J Blades
Drainable Head
Sloped Sill
EDJ-430
Separator Plate
Drainable Head
Exhaust Blades
Sloped Sill
Intake Blades
ESID-430
Drainable Head
EDK-402
K Blades
Sloped Sill
• Drainable head member improves ability to prevent water penetration due to an additional drain gutter, designed
to capture water.
• Models EDJ-430 and EDK-430 have optional 30 degree blades designed to maximize free area.
• Model ESID-430 is an air intake/discharge louver, which helps prevent the short cycling of air.
J Blades
Drainable Head
Sloped Sill
6
AdjustableNon-Drainable
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
ESJ-202 2 J 0.063 0.063 6.01 38 668 0.062 4015 5853
ESJ-401 4 J 0.081 0.081 8.44 53 691 0.085 5832 7962
ESJ-602 6 J 0.081 0.081 8.73 55 739 0.088 6452 8401
ESK-402 4 K 0.081 0.081 8.45 53 689 0.075 5822 8216
ESK-602 6 K 0.081 0.081 8.46 56 772 0.097 6531 8322
* Test size: 48 x 48 in. unit @ 15 min. duration J = J Style K = K Style
ESJ-401 ESK-402
Non-Drainable Head
J Blades
Sloped Sill
Non-Drainable Head
K Blades
Sloped Sill
J Blade K Blade
Greenheck Offers Non-Drainable Blade Options
• Traditional stationary J or K blade styles.
• K blade has as additional offset or “rain hook” for extra protection against water penetration.
• Design incorporates hidden mullions for continuous blade appearance when multiwidth sections are needed.
7
CombinationRecessed Mullion
ESJ-401RM ESK-402RM
Non-Drainable Head
K Blades
Sloped Sill
Recessed Mullion
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
ESJ-401RM 4 J 0.081 0.081 8.58 54 658 0.074 5646 8350
ESJ-602RM 6 J 0.081 0.081 8.38 52 785 0.102 6578 8267
ESK-402RM 4 K 0.081 0.081 8.42 53 677 0.071 5700 8409
ESK-602RM 4 K 0.081 0.081 8.13 51 800 0.099 6504 8206
* Test size: 48 x 48 in. unit @ 15 min. duration J = J Style K = K Style
Non-Drainable Head
J Blades
Sloped Sill
Recessed Mullion
Typical Visible Mullion for Drainable Blade
multiwidth sections (p. 4)
Typical Hidden Mullion for Non-Drainable
multiwidth sections (p. 6)
Typical Recessed Mullion for RM Series and EHM
multiwidth sections (p. 4)
Greenheck Offers Multiple Mullion Options
• Recessed mullion designs offer better blade alignment for a true continuous blade appearance.
• Provides more structural integrity between multiwide sections.
• Easier installation with minimal field adjustments.
• Models are easier to seal in the field and thermal expansion is accounted for within the design.
8
Adjustable Blades
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
EAD-401 4 DA 0.081 0.125 6.54 41 920 0.179 6017 7074
EAD-601 6 DA 0.081 0.125 7.34 46 1007 0.140 7391 7962
EAD-635 6 DA 0.081 0.125 8.73 55 1107 0.150 9664
EADC-401 4 DA 0.081 0.125 5.84 37 920 0.179 5373 6314
EADC-601 6 DA 0.081 0.125 6.44 40 1007 0.140 6485 6986
EAH-401 4 J 0.081 0.125 6.48 41 1023 0.128 6629 5397
EAH-690
(45º Blade)6 J 0.081 0.125 6.32 40 1069 0.165 6756 5056
EAH-690
(90º Blade)6 J 0.081 0.125 10.87 70 - - - 10055
* Test size: 48 x 48 in. unit @ 15 min. duration J = J Blade DA = Drainable Adjustable
Concealed
Actuator
Location
Drainable
Head
Drainable
Adjustable
Blades
Flat Sill
EADC-401
Concealed
Blade
Linkage
Drainable Head
Adjustable Blades
EAH-401
Flat Sill
Concealed
Blade Linkage
EAH-690
Drainable Head
Adjustable Blades
Flat Sill
Concealed
Blade Linkage
• Design incorporates operable blades that can be opened or closed to protect air intake and exhaust openings in
exterior building walls.
• Louver blades are center pivoted and can be operated manually or by electric or pneumatic actuators.
• EAD and EAH Series offer concealed blade linkage.
• EADC Series offer both concealed blade linkage and a concealed electric actuator.
• Model EAH-690 provides 70% free area when blades are in full 90 degree open position.
EAD-401
Drainable
Head
Drainable
Adjustable
Blades
Flat Sill
Concealed
Blade
Linkage
EAD-635
Drainable
Head
35˚ Drainable
Adjustable
Blades
Flat Sill
Concealed
Blade
Linkage
9
AcousticalCombination Louver/Damper
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
EAC-401 4 DA 0.081 0.125 6.34 40 1192 0.170 7557 6062
EAC-601 6 DA 0.081 0.125 7.41 46 1020 0.130 7558 7146
EACA-601 6 DAF 0.081 0.125 7.68 48 1221 0.170 9377 9586
EACC-401 4 DA 0.081 0.125 5.59 35 1192 0.170 6663 5341
EACC-601 6 DA 0.081 0.125 6.20 39 1020 0.130 6324 5977
EACN-601 6 J 0.081 0.125 7.18 45 1193 0.201 8566 7593
ECD-401 4 DA 0.081 0.081 7.60 46 1018 0.176 7737 7769
ECD-601 6 DA 0.081 0.081 7.32 48 1035 0.150 7866 7700
GCE-202 2 JG 0.063 0.063 4.96 31 - - - -
GCE-402 4 JG 0.081 0.081 6.36 40 - - - -
GCI-202 2 JG 0.063 0.063 5.26 33 - - - -
GCI-402 4 JG 0.081 0.081 6.39 40 - - - -
* Test size: 48 x 48 in. unit @ 15 min. duration DA = Drainable Adjustable DAF = Drainable Airfoil JG = J Blade Gravity J = J Blade
Drainable Head
Exposed
On-Blade Linkage
Flat Sill
ECD-401
Adjustable Intake
Gravity Blades
GCI-402
Stationary Blades
Drainable Head
Sloped Sill
GCE-402
Drainable Head
Adjustable Exhaust
Gravity Blades
Stationary Blades
Sloped Sill
EACC-401
Drainable
Stationary Blades
Drainable Head
Center Pivot
Adjustable Blade
Flat Sill
Concealed Blade
Linkage
Concealed
Actuator Location
EACA-601
Drainable
Stationary Blades
Drainable Head
Center Pivot
Adjustable
Airfoil Blade
Sloped Sill
Concealed Blade
Linkage
EACN-601
Drainable Head
Center Pivot
Adjustable Blade
Concealed Blade
Linkage
Stationary Blades
Flat Sill
• Maintains a stationary appearance when adjustable blades are closed.
• ECD Series offer exposed on-blade linkage.
• EAC Series and Model EACN-601 offer concealed linkage and center
pivot operable blades.
• Model EACA-601 incorporates airfoil blades.
• EACC Series offer both concealed blade linkage and concealed
electric actuator.
• GCE and GCI Series require an exhaust or intake fan for proper
operation.
Drainable
Stationary Blades
Drainable Head
Center Pivot
Adjustable Blade
Flat Sill
Concealed Blade
Linkage
EAC-401
Page Header
10
Sightproof
Drainable
Sightproof Blades
Drainable
Sightproof Head
Flat Sill
Sightproof Blades
Drainable
Sightproof Head
Flat Sill
SEH-401
Sightproof Blades
Sightproof Head
Flat Sill
SES-401 SEV-401
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
SED-202 2 CD 0.063 0.063 3.42 21 903 0.243 3088 2168
SED-401 4 CD 0.081 0.081 5.16 32 747 0.280 3855 2589
SED-501 5 CD 0.081 0.081 9.11 57 1134 0.448 10331 7364
SEH-202 2 C 0.063 0.063 3.73 23 600 0.137 2238 2140
SEH-401 4 C 0.081 0.081 5.16 32 765 0.276 3947 2664
SES-202 2 C 0.063 0.063 3.75 24 516 0.105 1935 2118
SES-401 4 C 0.081 0.081 5.33 33 718 0.224 3827 2695
SEV-401 4 V 0.081 0.081 5.33 33 - - - -
SEV-501 5 V 0.081 0.081 9.11 57 - - - -
* Test size: 48 x 48 in. unit @ 15 min. duration C = Chevron CD = Chevron Drainable V = Vertical
Vertical Blades
Flat Head
Flat Sill
SED-401
Drainable
Sightproof Blades
Drainable
Sightproof Head
Flat Sill
SED-501
• Louvers are designed to prevent visual see-through, can be applied as air intake or discharge louvers, or can be
applied as louvered equipment screens.
• SES Series most economical of all sightproof models.
• SEH Series incorporates a drainable head member for increased protection against water penetration.
• SED Series offer both a drainable head member and drainable blades for maximum protection against water
penetration.
• Model SED-501 offers 57% free area.
• SEV Series offer a vertical sightproof blade design.
Page Header
11
Wind-Driven Rain
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15
in. wg (cfm)
EHH-201 2 RR 0.063 0.063 6.20 39 914 0.198 5667 5487
EHH-401 4 RR 0.081 0.081 6.72 42 1250 0.295 8400 5782
EHH-501 5 RR 0.081 0.081 6.80 43 1210 0.224 8500 5998
EHH-601 6 RR 0.081 0.081 7.58 47 1250 0.323 9475 6091
EHH-701 7 RR 0.081 0.081 6.99 43 1250 0.423 8962 4522
EVH-201 2 RR 0.063 0.063 5.71 36 1250 0.368 7138 5185
EVH-401 4 RR 0.081 0.081 6.38 40 1250 0.369 7975 5897
EVH-602 6 RR 0.081 0.081 5.88 39 1250 0.161 7350 8146
EVH-801 8 RR 0.081 0.081 5.05 32 1250 0.100 6313 8627
* Test size: 48 x 48 in. unit @ 15 min. duration RR = Rain-Resistant
Wind-Driven Rain Test Results Wind Velocity - 29 mph Rainfall - 3 in./hr.³
Wind Velocity - 50 mph Rainfall - 8 in./hr.³
Airflow (cfm)
Free Area Velocity
(fpm)
Core Area Velocity (fpm)1
Water Penetration
Effectiveness
Water Penetration
Classification
Water Penetration
Effectiveness
Water Penetration
Classification
EHH-2011372 298 127 99.6% A - -
0 0 0 - - 99.1% A
EHH-4019306 1807 864 99.9% A - -
4142 804 400 - - 99.0% A
EHH-5018353 1564 776 99.1% A - -
7353 1377 683 - - 99.2% A
EHH-6017276 1257 676 99.8% A - -
8211 1418 763 - - 99.2% A
EHH-7018430 1522 783 100% A - -
7222 1304 671 - - 99.5% A
EVH-2019301 2178 864 99.8% A - -
9278 2173 862 - - 99.6% A
EVH-4017248 1604 673 100% A - -
6135 1357 570 - - 99.7% B
EHH-401 EVH-401
Wind-Driven Rain Penetration Classes
Class Effectiveness
A 1 to 0.99
B 0.989 to 0.95
C 0.949 to 0.80
D Below 0.8
EHH 401HHHHEE
Horizontal Rain-
Resistant Blades
Drainable Head
**Formed Aluminum Sill Pan
EVH 401EVHH 1111
Vertical Rain-
Resistant Blades
**Formed Aluminum Sill Pan
Drainable Head
**Shipped loose formed aluminum sill pan required for models EHH-201, EHH-401, EHH-501, EHH-601, EVH-201, EVH-401.
• The most effective line of products for minimizing water penetration through openings that are sensitive to rain
penetration.
• All models incorporate a drainable head member and either vertical (EVH Series) or horizontal (EHH Series) rain-
resistant blades to provide maximum resistance to wind-driven rain, as tested by the stringent AMCA 500L test
procedure.
EVH-60210564 2224 981 99.9% A - -
10427 2195 968 - - 100% A
EVH-8018337 1654 774 99.0% A - -
9299 1845 864 - - 99.2% A1 Core area is the open area of the louver face (face area less louver frames). Core area velocity is the airflow velocity through the core
area of the louver.
Page Header
12
Florida Product Approved
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
AFJ-601X 6 J 0.080 0.080 4.89 31 799 0.065 3907 6015
EHH-501X 5 RR 0.081 0.081 6.80 43 1250 0.224 8500 5998
ESD-435X 4 D 0.081 0.081 8.98 56 1151 0.213 10336 9281
ESD-635X 6 D 0.081 0.081 9.41 59 1077 0.173 10135 9932
EVH-602X 6 RR 0.081 0.081 5.88 37 1250 0.174 7350 7873
* Test size: 48 x 48 in. unit @ 15 min. duration RR = Rain-Resistant J = J Style D = Drainable
EHH-501XFlorida Product Approved No.:
FL6876.2
Rain-Resistant Blades
Drainable Head
+Formed aluminum sill pan
ESD-435XFlorida Product Approved No.:
FL6876.3
Drainable Blades
Drainable Head
Sloped Sill
ESD-635XFlorida Product Approved No.:
FL6876.4
Drainable Blades
Drainable Head
Sloped Sill
EVH-602XFlorida Product Approved No.:
FL7494.1
Vertical Rain
Resistant Blades
Flat Sill
Formed Sill Pan
Drainable Head
AFJ-601XFlorida Product Approved No.:
FL6876.1
Formed Acoustical J Blades
with Fiberglass Insulation
Perforated Aluminum
Insulation Screen
Formed
Acoustical Head
Formed
Acoustical Sill
+Shipped loose formed aluminum sill pan required for model EHH-501X.
• All mechanically fastened Florida Product Approved models comply with TAS-202 and Uniform Static Pressure
Test (ASTM E330).
• Models also comply with TAS-201 Large Missile Impact Test (ASTM E1996) and TAS-203 Cyclic Wind Pressure
Load Test with optional welded construction.
• Approved for use in Florida’s High-Velocity Hurricane Zone if Miami-Dade Notice of Acceptance is not required.
Page Header
13
Florida Product Approved
Model Name
Max. Wind-load
AMCA
Certifications
AMCA
Listed
Miami-Dade
County, FL
NOA No.
Florida
Product
Approved No.
Protocols
Minimum Opening Maximum Section Maximum Opening
Dimensions – inches (mm)
Miami-Dade County Qualified Louvers and Penthouses
ESS-502D 110 PSF
Water, Air
AMCA 540 Enhanced Level E
09-0519.14 EXP. 8/5/14
FL12941.1
TAS 201, TAS 202, TAS 203
8 W x 7 H (203 W x 178 H)
144 W x 144 H, Limited to 72 ft 2 (3658 W x 3658 H, Limited to 6.7m2)
Unlimited W x 144 H(Unlimited W x 3658 H)
ESD-635D*
150 PSF AMCA 540 Basic Level D,
AMCA 540 Enhanced Level E
(with 0.125 blade/frame)
12-0830.07 EXP. 12/6/17
FL10088.312 W x 12 H (305 x 305)
72.563 W x 144.813 H(1843 W x 3678 H)
Unlimited W x 144.813 H(Unlimited W x 3678 H)
ESD-635D/VCD-40 150 PSF
FL10088.412 W x 15.25 H (305 W x 387 H)
36.563 W x 144.813 H(928 W x 3678 H)
Unlimited W x 144.813 H(Unlimited W x 3678 H)
EHH-601D* 150 PSF
Water, Air and Wind Driven
Rain
AMCA 540 Enhanced Level E
12-0830.08 EXP. 11/1/17
FL10088.112 W x 7 H
(305 W x 178 H)72.563 W x 144.813 H
(1843 W x 3678 H)Unlimited W x 144.813 H(Unlimited W x 3678 H)
EHH-601D/VCD-40 150 PSF
AMCA 550, AMCA 540
Enhanced Level E
FL10088.2
TAS 201, TAS 202, TAS 203, TAS 100A
12 W x 13.25 H (305 W x 337 H)
36.563 W x 144.813 H(928 W x 3678 H)
Unlimited W x 144.813 H(Unlimited W x 3678 H)
EVH-602D 150 PSF
11-1103.01 EXP. 12/7/16
FL8042.1TAS 201, TAS 202, TAS 203
12 W x 16 H (305 W x 406 H)
48.25 W x 96.25 H(1226 W x 2445 H)
Unlimited W x 96.25 H(Unlimited W x 2445 H)
EVH-602D/VCD-40 150 PSF
FL8042.2TAS 201, TAS 202, TAS 203, TAS 100A
EVH-660D 150 PSF
12-0418.06EXP. 10/4/17
FL8042,16086.1
6 W x 12 H(153 W x 305 H)
48 W x 144 H(1219 W x 3658 H)
Unlimited W x 144 H(Unlimited W x 3658 H)
EHH-601PD 115 PSF
Not Applicable
Not Applicable
13-0510.06 EXP. 6/19/18
FL11350.1
TAS 201, TAS 202, TAS 203
MinimumThroat W x L x Max. H
12 x 12 x 12 (305 x 305 x 305)
Maximum Throat W x L x Max. H
84 x 108 x 84 (2134 x 2743 x 2134)
Maximum Throat W x L x Max. H
84 x 108 x 84 (2134 x 2743 x 2134)
ESD-635PD 115 PSF
13-0510.05 EXP. 6/19/18
FL11350.2
MinimumThroat W x L x Max. H
12 x 12 x 12 (305 x 305 x 305)
Maximum Throat W x L x Max. H
84 x 108 x 84 (2134 x 2743 x 2134)
Maximum Throat W x L x Max. H
84 x 108 x 84 (2134 x 2743 x 2134)
Florida Product Approved Louvers
AFJ-601X Max. 200 PSF^
Water, Air and Sound
AMCA 540 Enhanced Level E
Not Applicable
FL6876.1,15718.1
Standard: TAS 202
Welded: TAS 201, TAS 202, TAS 203
12 W x 15 H(305 W x 381 H)
60 W x 96 H(1524 W x 2438 H)
Unlimited W x 96 H(Unlimited W x 2438 H)
ESD-435X* Max. 200 PSF^
Water, Air
AMCA 540 Basic Level D
FL6876.3,15718.3
12 W x 9 H (305 W x 229 H)
120 W x 144 H Limited to 70 ft 2
(3048 W x 3658 H Limited to 6.5m2)
Unlimited W x 144 H or 120 W x Unlimited H
(Unlimited W x 3658 Hor 3048 W x Unlimited H)
ESD-635X* Max. 200 PSF^
AMCA 540 Basic Level D,
AMCA 540 Enhanced Level E
(with 0.125 blade/frame)
FL6876.4,15718.4
12 W x 12 H (305 W x 305 H)
EHH-501X* Max. 200 PSF^
Water, Air and Wind Driven
Rain
AMCA 540 Enhanced Level E
FL6876.2,15718.2
12 W x 7 H (305 W x 178 H)
EVH-602X Max. 200 PSF^
AMCA 550, AMCA 540
Enhanced Level E
FL7494.1,15719.1
12 W x 16 H (305 W x 406 H)
60 W x 96 H(1524 W x 2438 H)
Unlimited W x 96 H(Unlimited W x 2438 H)
FEMA 361 Tornado Grille
FSG-801 Max. 248 PSF
Not Applicable(UL Listed)
ICC 50012 W x 12 H
(305 W x 305 H)
57 ft 2
(configuration dependent)
Unlimited W x Unlimited H(Limited to 1 section
W or H)
*Also available in architectural shapes. ^Size/section dependent.
Page Header
14
Miami-Dade Qualified
EVH-602DFlorida Product Approved No.: FL8042.1
NOA NO.: 06-0711.1
ESS-502DFlorida Product Approved No.: FL12941.1
NOA NO.: 09-0519.15
• Use within Florida’s High-Velocity Hurricane Zone when a Miami-Dade Notice of Acceptance is required.
• All models comply with Miami-Dade structural test protocols TAS-201, Large Missile Impact Test (ASTM E1996);
TAS-202, Uniform Static Pressure Test (ASTM E330) and TAS-203, Cyclic Wind Pressure Test.
• Models ESD-603D with HCD-240, EHH-601D with VCD-40 and EVH-602D with VCD-40 also comply with
Miami-Dade’s test protocol TAS 100A, Wind-Driven Rain Resistance Test.
ESD-635DFlorida Product Approved No.: FL10088.3
NOA NO.: 07-1015.06
ESD-635D with VCD-40Florida Product Approved No.: FL10088.4
NOA NO.: 07-1015.06
EHH-601DFlorida Product Approved No.: FL10088.1
NOA NO.: 08-0229.06
EHH-601D with VCD-40Florida Product Approved No.: FL10088.2
NOA NO.: 07-0925.02
Horizontal Rain-Resistant Blades
Flat Sill
Retaining Angle
Drainable Head
Horizontal Rain-Resistant Blades
Factory Installed
Control Damper
Manual Quadrant Actuator
(Electric also available)
Flat Sill
Retaining Angle
Drainable Head
Drainable Head
Drainable Blades
Sloped Sill
Retaining Angle
Drainable Blades
Factory Installed
Control Damper
Manual Quadrant
Actuator (Electric also
available)
Sloped Sill
Retaining Angle
Drainable Head
Drainable Head
Sightproof Blades
Flat Sill
Anchor Plates (typical at head and sill)
Drainable Head
Vertical Rain-Resistant
Blades
Sloped Sill
TAS 100A
Page Header
15
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
EACA-601D 6 DAF 0.081 0.125 7.68 48 1221 0.170 9377 9586
EHH-601D 6 RR 0.081 0.081 7.58 47 1250 0.323 9475 5794
ESD-635D 6 D 0.081 0.125 9.41 59 1077 0.173 10135 9932
ESS-502D 5 C 0.081 0.081 8.19 51 1036 0.218 8485 6286
EVH-602D 6 RR 0.081 0.081 5.88 37 1250 0.174 7350 7873
EVH-602D/
VCD-406 RR 0.081 0.081 5.88 37 1250 0.174 7350 7873
EVH-660D 6 RR 0.063 0.095 7.29 45 1250 0.285 9113 7160
* Test size: 48 x 48 in. unit @ 15 min. duration RR = Rain-Resistant C = Chevron D = Drainable DAF = Drainable Airfoil
Horizontal Rain-
Resistant Blades
Miami-Dade Qualified
Hinged Hood(s) Member
Optional factory provided roof curb available.
EHH-601PDFlorida Product Approved No.: FL11350.1
NOA NO.: 08-0505.06
Hinged Hood(s) Member
Drainable
Blades
Optional factory provided roof curb available.
ESD-635PDFlorida Product Approved No.: FL11350.2
NOA NO.: 08-0505.05
EVH-602D with VCD-40Florida Product Approved No.: FL10088.4
NOA NO.: 07-1015.06
TAS 100A
Factory Installed
Control Damper
Anchor Plates (typical at head and sill)
Drainable Head
Vertical Rain-Resistant
Blades
Sloped Sill
Manual Quadrant
Actuator
EVH-660DFlorida Product Approved No.: FL
NOA NO.:
TAS 100A
Vertical Rain-Resistant Blades
Flat Sill
Exterior Sill Baffle
EACA-601DFlorida Product Approved No.: PENDING
NOA NO.: PENDING
Center Pivot Adjustable
Airfoil Blade
Drainable Head
Concealed Linkage
Sloped Sill
Drainable Stationary Blade
16
Thinline
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
ESF-145 1.5 TL 0.063 0.063 6.08 38 - 0.055 3040 4925
ESJ-150 1.5 J 0.063 0.063 7.29 46 - 0.038 3645 7144
ESU-130 1.5 TL 0.063 0.063 10.9 69 - 0.055 5475 14235
ESU-130S 1.375 TL 0.063 0.063 11.41 71 - 0.030 5705 14833
ESU-150 1.5 TL 0.063 0.063 7.4 46 - 0.035 3700 9990
ESU-150S 1.375 TL 0.063 0.063 7.7 48 - 0.035 3850 10395
* Test size: 48 x 48 in. unit @ 15 min. duration TL = Thinline J = J Style
Blades
Support Strut
ESU-130S
Blades
Frame
ESF-145
ESU-150
Blades
Frame
Blades
Frame
ESJ-150
• Narrow profile products designed for interior and exterior applications.
• Framed units ideal for installation in curtain wall, window wall systems, and door applications.
• Models ESU-130S and ESU-150S are frameless and offer a total product depth of only 1.375 inches.
• Models ESU-130 and ESU-150 offer high free area and are low airflow resistance.
17
Acoustical
Free Field Noise
Reduction in Decibels
Selected 1/3 Octave Bands Center
Frequency Hz
125 250 500 1000 2000 4000 STC
AFA-801 10 8 10 14 20 15 8
AFJ-601 10 10 12 16 23 18 10
AFJ-801 11 11 13 19 28 20 12
AFJ-120 13 12 17 25 36 25 16
AFS-120 11 11 16 25 36 31 16
Sound Transmission Class (STC)The Sound Transmission Class (STC) is a rating of the effectiveness of an assembly in isolating or reducing airborne sound transmission. STC is a single number that summarizes airborne sound transmission loss data. Assemblies with higher STC ratings are more efficient at reducing sound transmission. STC is determined in accordance with ASTM E413-04.
Model Depth Blade Style
Blade Thickness
(in.)
Frame Thickness
(in.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
AFA-801 8 AF 0.080 0.080 5.21 33 879 0.050 4580 7508
AFJ-120 12 J 0.080 0.080 3.67 23 961 0.093 3527 4543
AFJ-601 6 J 0.080 0.080 4.89 31 799 0.065 3907 6015
AFJ-801 8 J 0.080 0.080 4.28 27 887 0.079 3796 5192
AFS-120 12 C 0.080 0.080 4.27 27 830 0.118 3544 3839
* Test size: 48 x 48 in. unit @ 15 min. duration AF = Airfoil C = Chevron J = J Style SP = Sightproof
Formed Acoustical Airfoil Blades
with Fiberglass Insulation
Perforated Aluminum
Insulation Screen
Formed Head
Formed Sill
AFA-801
AFS-120
Formed Acoustical Sightproof Blades
with Fiberglass Insulation
Perforated Aluminum
Insulation Screen
Formed
Acoustical Head
Formed
Acoustical Sill
AFJ-801
Formed Acoustical J Blades
with Fiberglass Insulation
Perforated Aluminum
Insulation Screen
Formed
Acoustical Head
Formed
Acoustical Sill
• Acoustically insulated blades provide sound absorption from escaping noise.
• Available in formed aluminum or steel material.
• AFJ Series is the most economical of all acoustical models.
• Model AFA-801 offers the highest free area, has the lowest airflow resistance, and is designed with acoustical
blades.
• Model AFS-120 offers the best sound absorption performance and incorporates sightproof blades.
18
Model Depth Blade Style
Blade Thickness
(Ga.)
Frame Thickness
(Ga.)
Free Area (sq. ft.)
Free Area (%)
Beginning Point of Water
Penetration (ft./min.)
Pressure Drop at Max. Intake
Velocity (in. wg)
Max. Intake Volume Flow Rate (cfm)
Exhaust Volume Flow Rate @ 0.15 in. wg (cfm)
FAD-402 4 DA 16 16 5.98 38 1086 0.130 6494 7478
FAD-602 6 DA 16 16 7.11 45 980 0.129 6968 7768
FAD-635 6 DA 16 16 8.77 55 959 0.099 8410 11093
FAJ-402 4 A 16 16 5.93 37 691 0.062 4096 6278
FAJ-602 6 J 16 16 6.23 39 717 0.064 4467 6551
FDS-402 4 D 20 16 7.03 44 1056 0.161 8788 8444
FDS-602 6 D 20 16 8.15 51 948 0.137 7726 8661
FSJ-402 4 J 20 16 7.55 47 839 0.110 6335 6894
FSJ-602 6 J 20 16 7.57 47 896 0.125 6783 7398
* Test size: 48 x 48 in. unit @ 15 min. duration J = J Style D = Drainable A = Adjustable
Fabricated
FAJ-402FAD-402
Formed Head Member
Formed
Stationary Blades
Formed Flat Sill
Formed Adjustable
Drainable Blades
Formed Head Member
Formed Flat Sill
Formed Adjustable
J Blades
Formed
Stationary Blades
FDS-402
Formed Head Member
Formed Flat Sill
Formed Drainable
Stationary Blades
FSJ-402
Formed Head Member
Formed Flat Sill
Formed Stationary
J Blades
• Fabricated from galvanized steel and are low cost compared to extruded aluminum models.
• All fabricated models are available in stainless steel material.
• FSJ and FDS Series have stationary blades only.
• FAD and FAJ Series are adjustable blade models.
19
Special Application
PEV-400 EES-401WIH/WRH
PPPenthouses & Equipment ScreensModel PEV-400 is a gravity ventilator comprised of three sides of standard stationary non-drainable louver model ESJ-401, along with one side of 0.125-in. thick plate glass that can be broken with the pressure of a fire hose. AA fire smoke damper is located in the throat of the curb and wired into the fire control panel. The unit is shop-aassembled and shipped complete.
GGreenheck penthouse models WIH and WRH offer clean horizontal lines, mitered corners, all aluminum cconstruction, removable hoods, and weather-resistant blades. Custom louvered penthouses are also available to meet your specifications. For more information contact your local rep or visit greenheck.com
For screen applications, model EES-401 is an inverted horizontal equipment screen offering extruded aluminum “JJ” styly e blades. As alwayys,, custom configgurations are available.
FFFFFFFEEMMAA 336611 GGriilllleFEMA 361 grilles are used to protect air intake or exhaust openings from fflying debris, caused by tornadoes spawned by hurricanes or severe tthunderstorms, and must be applied over any wall penetration on a FEMA 361 storm shelter. Model FSG-801 is a FEMA 361 compliant, UL Classified(R29119) grille, and fabricated of 0.25 inch thick hot-rolled steel materials.Model FSG-801 withstands the ICC 500 2 x 4 impact standard adopted by FEMA 361 and withstands wind-loads up to 248 PSF.
Model FSG-801 may be installed in a cantilever or recessed/flush mount configuration. Mounted flanges may be located on the sides, top, and bottom. Nearly any Greenheck louver may be factory installed within the optional deep sleeve when using the flush/recessed mounting configuration, including many of our Miami-Dade Qualified and all of Florida Product ApApApAApApAA prpppp ovo eded llououveerss.
SSSSSSSSandd LLouverGGreenheck’s sand louver is designed to protect air intake and exhaust openings in building exterior walls from wind-driven sand. Design incorporates vertical ssightproof blades to separate sand from the airstream, which is then channeled oout at the sloped sill.
Model FSL-401 was tested per ASHRAE Standard Method 52.1-1992 ((previously ASHRAE standard 52-76), an independent third-party test lab using ccrushed quartz of (150-300 μm) dust medium. Standard construction material isggalvanized steel and optional formed aluminum is available. Frame depth: 4 in.
FSG-801
FSL-401
P.O. Box 410 • Schofield, WI 54476-0410 • Phone (715) 359-6171 • greenheck.com
Bird Screen or Insect Screen
Flanged Frame
Structural Reinforcing
Glazing Adapters
SillExtensions
Anchor Clips
Security Bars
Blank Off Panels
Filters & Filter Racks
We have a full line of accessories, so whether your project necessitates security bars or filter racks, we have what you need. An extensive line of standard finishes, including Kynar® paint, baked enamel paint, industrial coatings or anodize finishes are also available. In addition to our complete line of standard colors, our custom color matching capabilities are endless. These accessories and options allow Greenheck to complete your project just as you envision it.
Greenheck Fan Corporation
certifies that Models EVH-
201, 401, 602, 801; EHH-
201, 401, 501, 601, 701;
EVH-602D; EHH-601D; EHH-
501X; and EVH-602X are
licensed to bear the AMCA
Seal. The ratings shown are
based on tests and proce-
dures performed in accordance with AMCA Publication
511 and comply with the requirements of the AMCA
Certified Ratings Program. The AMCA Certified Ratings
Seal applies to water penetration, air performance and
wind-driven rain.
Greenheck Fan Corporation certifies that
Models ESD-635D, 603D; ESS-502D;
ESD-435X, 635X; ESJ-202, 401, 602;
ESK-402, 602; ESJ-401RM, 602RM;
ESK-402RM, 602RM; EDJ-202, 401,
601, 430; EDK-402, 430, 602; ESD-
202, 403, 435, 603, 635; EDD-401,
601; EHM-601; SES-202, 401; SEH-
202, 401; SED-202, 401, 501; ECD-
401, 601; EAC-401, 601; EACA-601; EACN-601; EAD-401,
601; EAH-401; FSJ-402, 602; FDS-402, 602; FAJ-402, 602;
and FAD-402, 602, 635 are licensed to bear the AMCA Seal.
The ratings shown are based on tests and procedures per-
formed in accordance with AMCA Publication 511 and comply
with the requirements of the AMCA Certified Ratings Program.
The AMCA Certified Ratings Seal applies to water penetration
and air performance.
Greenheck Fan Corporation
certifies that Models EAH-
690 with blade angle at 90º
and FSL-401 are licensed
to bear the AMCA Seal. The
ratings shown are based
on tests and procedures
performed in accordance
with AMCA Publication 511
and comply with the requirements of the AMCA
Certified Ratings Program. The AMCA Certified
Ratings Seal applies to air performance.
Greenheck Fan
Corporation certifies
that Models AFJ-120,
601, 801; AFA-801;
AFS-120; and AFJ-
601X are licensed to
bear the AMCA Seal.
The ratings shown are
based on tests and
procedures performed in accordance with
AMCA Publication 511 and comply with the
requirements of the AMCA Certified Ratings
Program. The AMCA Certified Ratings Seal
applies to water penetration, air performance
and sound ratings.
00.LVR.1000 R4 1-2014 IP Copyright © 2014 Greenheck Fan Corporation
Accessories and Options
As a result of our commitment to continuous improvement, Greenheck reserves the right to change
specifications without notice.
Specific Greenheck product warranties are located on greenheck.com within the product
area tabs and in the Library under Warranties.
Our Commitment
Prepared to SupportGreen Building Efforts
The Greenheck Fan Corporation certifies that Louver Type ESD-435X, ESD-635X, ESD-635D, AFJ-601X, EHH-501X, EVH-602X, ESS-502D, EHH-601D, EVH-602D and EVH-660D shown herein are approved to bear the AMCA Listing Label. The ratings shown are based on tests and procedures performed in accordance with AMCA Publications and comply with the requirements of the AMCA Listing Label Program