level 1 - iit kanpur
TRANSCRIPT
![Page 1: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/1.jpg)
LEVEL 1
![Page 2: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/2.jpg)
The Quiz will be conducted in two levels LEVEL 1
• This level consist of 25 questions MCQ type (+4 -0) or One word and 5 Fact based questions.
• Each question will be displayed on the screen for sufficient duration, just after which next question will follow.
• All the teams will be provided with an answer sheet. • All the subjective questions must be answered in a word in space given• Negative Marking only in Fact based questions (+4, -2)
LEVEL 2• Clearing Threshold cutoff for L1 is necessary.• Rules and regulations of Level 2 will be disclosed after L1.
![Page 3: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/3.jpg)
1.“Excellence for Everyone” is the tagline of which famous automobile company ?
A) Chevrolet Motor
B) BMW
C) Mercedes-Benz
D) Toyota Motor
![Page 4: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/4.jpg)
2. What is the tension in a rope shown in figure 1 if T1< T2?
C) T2 – T1
B) T2
A) T1
D) Zero
![Page 5: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/5.jpg)
3. The flow through a nozzle is regarded as
C) Isothermal flow
B) Constant pressure flow
A) Constant volume flow
D) Isentropic flow
![Page 6: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/6.jpg)
4. Which of the following symptom is caused as a result
of brake disc run out ?
A) Ineffectiveness of the brakes
B) Judder during braking
C) Localized wearing of the brake pads
D) Rapid wearing of the brake pads
![Page 7: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/7.jpg)
5. The first Indian automobile company is
A. Tata motors limited
B. Hindustan Motors Limited
C. Ashok Leyland
D. Chinkara Motors
![Page 8: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/8.jpg)
6. What refers to the parallel axis theorem for second
moment of area?
A. Mohr’s theorem
B. Steiner’s theorem
C. Maxwell’s theorem
D. Young’s theorem
![Page 9: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/9.jpg)
7. In a ball bearing, ball and bearing forms a
A. Turning pair
B. Rolling pair
C. Screw pair
D. Spherical pair
![Page 10: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/10.jpg)
8.
Talking about extensive properties which one of the following is wrongly placed….
(all terms have their usual meaning)
U, T, V, S, G, H
![Page 11: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/11.jpg)
9. The connecting rod is attached to the piston by the
A. Cap boltB. Gudgeon pin
C. Cap roller bearingD. Rod cap
![Page 12: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/12.jpg)
10. “Digital Twin Spark Ignition” technology is patent of which company?
B) YAMAHA
C) BAJAJ
A) HONDA
D) TVS
![Page 13: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/13.jpg)
11. The temperature of piston will be more at
A) THE PISTON WALLS
B) THE CROWN OF PISTON
C) THE SKIRT OF PISTON
D) THE PISTON PIN
![Page 14: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/14.jpg)
12. Knocking tendency in SI engine reduces with increasing:
A) Compression Ratio
B) Wall temperature
C) Engine speed
D) None
![Page 15: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/15.jpg)
13. In commercial vehicle layouts engine is located
forward, rear or under floor mainly to
A) Better utilization of space
B) Increase fuel economy
C) Better weight distribution
D) Reduce the weight of chassis
![Page 16: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/16.jpg)
14. Which of the following generally drive the oil pump
A) Cam shaft
B) Crank shaft
C) Battery
D) Chain drive
![Page 17: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/17.jpg)
15. If the air-fuel mixture ignites before the spark takes place at spark plug, the condition is called
A) DETONATION
C) RUMBLE
B) IGNITION
D) PRE-IGNITION
![Page 18: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/18.jpg)
16. Identify the given mechanical component
![Page 19: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/19.jpg)
17. Name the car company.
![Page 20: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/20.jpg)
18.The forward transfer of weight to the front wheels result in imbalance of vehicle along Y-axis, this phenomenon is known as
![Page 21: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/21.jpg)
19.If SUV refers to Sports Utility Vehicle, what does CUV refers to
A.Compact Utility Vehicle
B.CrossOver Utility Vehicle
C.Central Utility Vehicle
D.Common Utility Vehicle
![Page 22: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/22.jpg)
20.Identify the component of the steering system.
![Page 23: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/23.jpg)
21.
TO WHICH COMPANY DOES THIS FAMOUS LOGO BELONGS…
![Page 24: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/24.jpg)
22.
IDENTIFY THIS CAR , INCLUDED IN LIST OF WORLD’S 5 FASTEST CARS.
![Page 25: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/25.jpg)
23.
IDENTIFY LOGO
![Page 26: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/26.jpg)
24. First I.C Engine Was Installed In
A. CAR
B. BOAT
C. TRUCK
D. PLANE
![Page 27: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/27.jpg)
25. Identify the component
![Page 28: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/28.jpg)
![Page 29: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/29.jpg)
26.THE TWO MESHED GEAR HAVE GEAR RATIO OF 3:1. EVERY TIME
THE LARGER GEAR TURNS ONCE, SMALLER WILL TURN 1/3 TIMES
SERIOUS JOKING
![Page 30: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/30.jpg)
27.THE DEVICE FOR SMOOTHING OUT THE POWER IMPULSE FROM ENGINE IS CALLED CLUTCH
SERIOUS JOKING
![Page 31: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/31.jpg)
28.THE PORTION OF CRANKSHAFT WHICH RESTS ON CYLINDER BLOCK IS CALLED MAIN JOURNAL
SERIOUS JOKING
![Page 32: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/32.jpg)
29.
“DRIVING IS BELIEVING” IS ONE OF THE TAGLINES OF HYUNDAI
SERIOUS JOKING
![Page 33: LEVEL 1 - IIT Kanpur](https://reader030.vdocuments.us/reader030/viewer/2022012807/61bd4e9c61276e740b117bba/html5/thumbnails/33.jpg)
30.
The torque available at the contact between driving wheels and road is known as tractive effort.
SERIOUS JOKING