layher event systems catalogue · edition 04.2015 ref. no. 8111.227 quality management certified...

Edition 04.2015Ref. No. 8111.227

Quality management certified accordingto ISO 9001:2008 by German TÜV-CERT

LAYHER EVENT SYSTEMSCATALOGUE

2

Layher

Headquarters in Eibensbach

Plant 2 in Gueglingen

HERE IS THE BEATING HEART OF LAYHER.

Quality made by Layher comes from Gueglingen-Eibensbach. Our company

has set down deep local roots since it was established. Right up until today,

development, production, logistics and management are all in one place, where

the conditions are best for achieving quality made by Layher: in Gueglingen-

Eibensbach. The two locations together cover a surface area of 318,000 m².

This includes more than 142,000 m² of covered production and storage areas.

This is where our scaffolding systems are created by highly automated

production. Short distances and short reaction times mean we can adapt

production to suit our customers’ requirements, flexibly and at any time.

MORE POSSIBILITIES. THE SCAFFOLDING SYSTEM.

This brand promise made by Layher is the expression of a brand philosophy that

we’ve been living by for over 70 years. More speed, more safety, more proximity,

more simplicity and more future: values with which we strengthen our customers’

competitiveness in the long term. With our innovative systems and solutions,

we’re working all the time on making scaffolding construction even simpler, even

more economical and, above all, even safer. With comprehensive services, a

permanent range of training courses and an ethos of customer focus, more than

1,500 dedicated Layher employees are creating more possibilities for our

customers every single day. In more than 30 countries all over the world.

QUALITY MADE BY LAYHER

3

MORE SPEEDWe can supply any required quantity of the right products at the right time – to anywhere in

the world. Layher has subsidiaries in more than 30 countries in all five continents, with a

tight-knit network of national service centers. Speed is also the motto of our logistics

concept. Customers have the choice of picking up their material at a Layher service center or

having it delivered either to a warehouse or “just in time” directly to the site.

MORE EXPERIENCETradition has grown into experience and expertise. Our experts pass on this knowledge – all

over the world. Existing customers might want to try a different approach, while new

customers might need support when assembling a Layher scaffolding structure. Layher’s

specialists get to grips with the specific tasks and requirements, devising for our customers

persuasive solutions that are both profitable and efficient. Good advice from Layher is

guaranteed. We take care of our customers at every level, because cooperation with them on

the basis of mutual trust as well as their success are important to us.

MORE KNOWLEDGEFurther training is the key to success. For this reason, Layher organizes regular training

seminars that prepare our customers for current and future challenges specifically in

scaffolding. This training scheme is backed up by many others options, for example practical

product training courses and regular meetings for scaffolding erectors to promote the flow of

information between experts and colleagues. And last but not least, Layher offers

comprehensive publications on all topics to do with scaffolding construction.

MORE CLARITYSaving time, using material in the best way, improving logistics. All that can be done with

Layher’s planning software, LayPLAN, or the special Layher tools for AutoCAD®. Layher

software means greater reliability when budgeting and planning scaffolding construction

projects. Optimization of inventory management and complete cost transparency for the

material used in a project. Once the dimensions and the required assembly variant have been

entered, the Layher software supplies a scaffolding proposal with matching material list

within seconds.

MORE QUALITYPeople talk a lot about quality. We just produce it. Quality from Layher means state-of-the-art

production processes, carefully selected materials, smart automation and a highly qualified

workforce. Our products comply with the very latest security standards and possess DIN ISO

certification, German TÜV approval, and many other German and international quality labels.

20,000 kilometres of steel tubing in high-quality workmanship are convincing testimony to

Layher’s quality standards.

More Possibilities. The Scaffolding System.

4

Contents

2 Truss systems Page 24

2 Leg insert platforms Page 16

2 Event stages Page 8

LAYHER EVENT SYSTEMS

2 Benches, bucket seats, tip-up seats Page 22

Speedyscaf System

Ref. No. 8102.256

Allround Scaffolding System

Ref. No. 8116.252

Scaffolding Accessories

Ref. No. 8103.254

Protective Systems

Ref. No. 8121.253

Event Systems

Ref. No. 8111.227

Rolling Towers Ladders and Stairs

Ref. No. 8118.225

LAYHER SPEEDYSCAF SYSTEMCATALOGUE

®

Edition 04.2015Ref. No. 8102.256


LAYHER ALLROUND SCAFFOLDING SYSTEMCATALOGUE

®

Edition 04.2015Ref. No. 8116.252


Edition 04.2015Ref. No. 8111.227


LAYHER EVENT SYSTEMSCATALOGUE

LAYHER PROTECTIVE SYSTEMSCATALOGUE

Edition 04.2015Ref. No. 8121.253


LAYHER SCAFFOLDING ACCESSORIESCATALOGUE

Edition 04.2015Ref. No. 8103.254


LAYHER LADDERS & STAIRSLAYHER ROLLING TOWERS

CATALOGUE

Edition 04.2015Ref. No. 8118.225


THE LAYHER PRODUCT RANGE – ALL CATALOGUES AT A GLANCE

5

2 Event stands Page 18

2 FOH system Page 32

CONTENTS2 EVENT SYSTEMS

2 DECISION-MAKING AIDS 6

2 EVENT STAGES AND PODIA 8

2 BASIC COMPONENTS 10

2 GUARDRAILS AND STAIRWAYS 12

2 UNIVERSAL BASE 14

2 LEG INSERT PLATFORMS 16

2 EVENT STANDS 18

2 BASIC COMPONENTS AND GUARDRAILS 20

2 BENCHES AND BUCKET SEATS 22

2 TRUSS SYSTEMS 24

2 ALU TRUSS SYSTEMS 26

2 STEEL TRUSS SYSTEMS 30

2 FOH TOWER KIT SYSTEM 32

2 FOH SYSTEMS 34

2 ROOF AND WALL CLADDING 34

2 INDEX 36

All dimensions and weights are guideline values. Subject to technical modification.

Steel parts are galvanized according to EN ISO 4042 and EN 12811-2.

Our deliveries shall be made exclusively in accordance with our currently valid General Terms of Sale. These include the following provisions: The place of performance is Gueglingen-Eibensbach. Title to the delivered goods shall be retained until full payment has been made.

Please request the specific instructions for assembly and use when ordering. Protected by copyright. Not to be reproduced, either in whole or in part. Misprints and errors excepted.

6

Event Systems


®

Edition 04.2015Ref. No. 8116.252


Module EV 86 EV 86+ EV 86Q EV 100Metric*

EV 104

Bay 2.07 x 2.57 m 2.07 x 2.57 m 2.57 x 2.57 m 2.00 x 2.00 m 2.07 x 2.07 m

Deck type Event deck Event deck Event deck Event deck Event deck

Deck size 0.86 x 2.07 m 0.86 x 2.07 m 0.86 x 2.57 m 1.00 x 2.00 m 1.04 x 2.07 m

Decks per bay 3 3 3 2 2

Support element Event transom Event transom Event transom Event transom Event transom

Support element length 2.57 m 2.57 m 2.57 m 2.00 m 2.07 m

Crosspiece support – required – – –

Perm. load capacity 5.0 kN/m² 7.5 kN/m² 5.0 kN/m² 7.5 kN/m² 7.5 kN/m²

LAYHER STAGES Layher stages are just as suitable for use inside halls and marquees as use out -

doors. The components make up a construction kit allowing the building of a

small podium for fashion shows or bands, or a giant concert stage. All parts

are weatherproof, thanks to the use of aluminium, hot-dip galvanized steel and

coated plywood panels. On uneven surfaces, fast and easy adaptability of the

Allround stage to the lie of the land is a particular advantage. The permissible

loading capacity of the podium surface is up to 7.5 kN/m². The height can,

depending on the structural strength, be up to 10 m. Meeting of the guidelines

for temporary structures with the design loads as per DIN 4112 is verified by

inspection books issued by the competent authority.

DECISION-MAKING AIDS

LAYHER STAGE AND STAND SYSTEMS

* Further metric components, see catalogue Allround Scaffolding.

7

Seating stand EV 86 x 16 EV 86 x 25 EV 86 x 33 EV 100 x 25Metric*

EV 104 x 25

Step width 0.857 m 0.857 m 0.857 m 1.00 m 1.036 m

Step height 0.166 m 0.25 m 0.333 m 0.25 m 0.25 m

Riser angle [Degree] 11° 16.3° 21.1° 14° 13.6°

Riser angle [%] 19.4 % 29.2 % 38.6 % 24.9 % 24.2 %

Standard dimension 2.57 x 2.07 m 2.57 x 2.07 m 2.57 x 2.07 m 2.00 x 2.00 m 2.07 x 2.07 m

Loose seating possible possible possible recommended recommended

Permanently fitted benches recommended recommended recommended possible possible

Seating stand EV 75 x 16 EV 75 x 25 EV 75 x 33

Step width 0.75 m 0.75 m 0.75 m

Step height 0.16 m 0.25 m 0.33 m

Riser angle [Degree] 12.5° 18.4° 24°

Riser angle [%] 22.2 % 33.3 % 44.4 %

Standard dimension 2.25 x 2.00 m 2.25 x 2.00 m 2.25 x 2.00 m

Loose seating not possible not possible not possible

Permanently fitted benches possible possible possible

Bucket seats not possible not possible not possible

Tip-up seats recommended recommended recommended

LAYHER STANDSThe most important characteristics of Layher seating stands are: sturdy

material, sound workmanship, long service life, rapid assembly at changing

locations, and low transport volume. The individual parts are easy to assemble

and lightweight, so that they can be installed manually. Please refer to our

tables in this connection. Thanks to the modular design, it is possible to adapt

the stand to the local conditions and to plan it in accordance with German

regulations governing public assembly places.

DECISION-MAKING AIDS

8

Event stages and podia

LAYHER STAGES AND PODIA – EASIER, QUICKER AND SAFER BY USING THE MODULAR LAYHER SYSTEM

No restrictions imposed on performances, no limits set in the dimensions

and fittings, no concessions made to the location:

Layher podiums and stages always provide a safe play performance

area that’s exactly what’s needed. Series manufacture and high delivery

readiness are our way to help you cut costs and achieve economic

success; and tailor-made special solutions whenever necessary are our

strengths.

LAYHER EVENT STAGES AND PODIA

2 Basic unit

Can be expanded as required, variable floor plans.

2 Expandable

Caters for requirements with a variety of roof and support systems.

2 Allround base

High load-bearing capacity, rapid assembly and dismantling.

2 Practically-minded design

Strong connector technology, ergonomic handling, low-wear

aluminium parts, corrosion-proof thanks to hot-dip galvanisation,

space-saving storage.

THE BENEFITS TO YOU:

9

LAYHER STAGES AND PODIA – EASIER, QUICKER AND SAFER BY USING THE MODULAR LAYHER SYSTEM

10

Event stages – basic components

Event stages – basic components Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 86

QEV

100

EV 10

4

1 1 Event deck T10Aluminium frame, coated plywood, detachable plastic corners, threaded inserts for holding insert leg holders

1.00 x 2.00 28.3 10 5402.170 W 2

1.04 x 2.07 36.0 10 5402.180 W 2

0.86 x 2.07 27.5 10 5402.190 W 2

0.86 x 2.57 32.3 10 5402.191 W 2

2 2 Event deck T10, square for equalizing bays,aluminium frame, coated plywood, detachable plastic corners, threaded inserts for holding insert leg holders

1.00 x 1.00 14.3 10 5402.175 W 2

1.04 x 1.04 19.3 10 5402.185 W 2

3 3 Plastic corneras spare part for Event deck T10 (Pos. 1 and 2)

3.4 50 V 6494.101 W 2 2 2 2

4 4 Event transom 0.86 6.1 60 5400.072 W 2

1.00 6.4 60 5400.010 W 2

1.04 6.6 60 5400.020 W 2

1.71 10.0 60 5400.071 W 2

5 2.00 11.4 60 5400.040 W 2

2.07 12.0 60 5400.050 W 2

2.57 14.6 60 5400.070 W 2 2

6 7 5 Transom supportincreases permissible load on the EV 86+ system

2.57 x 0.50 21.2 40 5400.100 W 2

6 Tension clasp for transom 0.16 0.1 50 V 5403.514 W 2 2 2 2

8 9 10 7 Square half-coupler 1.4 5403.510 W 2 2 2 2

8 Base plate 20max. spindle travel 10 cm

0.20 2.3 200 5602.020 W 2 2 2 2

11


0.40 2.9 200 4001.040 W 2 2 2 2

12 13 14 10 Base plate 60, solid, without lockmax. spindle travel 41 cm

0.60 6.7 200 5602.060 W 2 2 2 2

11 Rubber pad for base platefor slip-reduction on solid grounds like concrete, asphalt, stone or timber. Protects sensitive deckings from damages.

0.20 x 0.20 0.4 4000.500 W 2 2 2 2

12 Base collar, short 0.17 1.1 250 5601.000 W 2 2 2 2

13 Standard, 0.67 m, with 2 rosettes, without spigotwith integrated base collar

0.67 3.6 200 2604.066 W 2 2 2 2


1.17 6.1 28 2604.116 W 2 2 2 2


®

Edition 04.2015Ref. No. 8116.252


For further base plates, see Scaffolding Accessories Catalogue

For all further Allround components, see Allround Scaffolding System Catalogue

The Event decks 1 and 2 up to 2.07 m in length are desi-gned for a load of 7.5 kN/m². The Event deck 2.57 m without transom support can bear 5 kN/m². The removable Plastic corners 3 ensure that the vertical tubes can pass through. The coated plywood board is braced with alu minium rungs. The 18 cm high Event transom 4 of aluminium section with connecting wedge heads of galvanised steel holds the Event decks. The load-bearing capacity of the 2.57 m long Event crosspiece can be increased by reinforcement with the Transom support 5 from 5 kN/m² to 7.5 kN/m².

The Tension clasp 6 of spring steel connects the Event deck to the Event transom and acts as a lock against lift-off.

A gap-free podium surface is assured by the Square half-coupler 7 to be fitted to the edge of the podium to prevent shifting.

The rubber pad 11 must not be used as load-distributing base. It minimizes slippery of the structure.

The Standard 0.67 m 13 and Standard 1.17 m 14 are used for podiums with heights of 0.80 m or 1.30 m and obviate the need for the base collar. The assembly runs faster and ballasting can be placed on the lowest scaffolding level.

With the Base plate 20 8 and the Base collars 12 very small heights, as encountered in trade fair and hall construction can be achieved. The Base plate 40 9 and the Base plate 60, solid 10 are used especially in stand construction and permit increased height adjustment.

The substructure of the Layher Event systems is created from Layher Allround scaffolding. Please refer to the Allround Scaffolding System Catalogue for the components required.

Event deck

Tension clasp

Event transom

11

WS = wrench size PU = packaging unit W = available ex works P = delivery time on request V = only available in this packaging unit

Event stages – basic components Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 86

QEV

100

EV 10

4

1 1 Event deck T10Aluminium frame, coated plywood, detachable plastic corners, threaded inserts for holding insert leg holders

1.00 x 2.00 28.3 10 5402.170 W 2

1.04 x 2.07 36.0 10 5402.180 W 2

0.86 x 2.07 27.5 10 5402.190 W 2

0.86 x 2.57 32.3 10 5402.191 W 2

2 2 Event deck T10, square for equalizing bays,aluminium frame, coated plywood, detachable plastic corners, threaded inserts for holding insert leg holders

1.00 x 1.00 14.3 10 5402.175 W 2

1.04 x 1.04 19.3 10 5402.185 W 2

3 3 Plastic corneras spare part for Event deck T10 (Pos. 1 and 2)

3.4 50 V 6494.101 W 2 2 2 2

4 4 Event transom 0.86 6.1 60 5400.072 W 2

1.00 6.4 60 5400.010 W 2

1.04 6.6 60 5400.020 W 2

1.71 10.0 60 5400.071 W 2

5 2.00 11.4 60 5400.040 W 2

2.07 12.0 60 5400.050 W 2

2.57 14.6 60 5400.070 W 2 2

6 7 5 Transom supportincreases permissible load on the EV 86+ system

2.57 x 0.50 21.2 40 5400.100 W 2

6 Tension clasp for transom 0.16 0.1 50 V 5403.514 W 2 2 2 2

8 9 10 7 Square half-coupler 1.4 5403.510 W 2 2 2 2


0.20 2.3 200 5602.020 W 2 2 2 2

11


0.40 2.9 200 4001.040 W 2 2 2 2

12 13 14 10 Base plate 60, solid, without lockmax. spindle travel 41 cm

0.60 6.7 200 5602.060 W 2 2 2 2

11 Rubber pad for base platefor slip-reduction on solid grounds like concrete, asphalt, stone or timber. Protects sensitive deckings from damages.

0.20 x 0.20 0.4 4000.500 W 2 2 2 2

12 Base collar, short 0.17 1.1 250 5601.000 W 2 2 2 2


0.67 3.6 200 2604.066 W 2 2 2 2


1.17 6.1 28 2604.116 W 2 2 2 2

12

Event systems – guardrails and stairways for stages

Event systems – guardrails and stairways for stages Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 86

QEV

100

EV 10

4

1 4 + 5 1 Guardrail post for podium 1.64 13.8 100 5406.000 W 2 2 2 2

2 Handrail T13handrail height 1.00 m

1.00 7.9 40 5417.100 P 2

1.04 8.1 40 5417.104 P 2

2.00 15.0 40 5417.200 P 2

2.07 15.4 40 5417.207 W 2 2

2.57 18.7 40 5417.257 P 2 2

3 Guardrail with child safety feature T12Guardrail height 1.10 m.Connection elements height adjustable for use with Event or scaffolding decks.

1.00 19.8 25 5409.100 W 2

1.04 20.0 25 5409.104 W 2

1.57 25.8 25 5409.157 W 2

2.00 30.5 25 5409.200 W 2

2.07 30.8 25 5409.207 W 2 2

2.57 35.8 25 5409.257 W 2 2

2 3 4 Stairway guardrail 750 with child safety featurefor stairway stringer Pos. 5

1.00 x 1.57 22.0 25 2616.106 W 2 2 2 2

5 U-Stairway stringer 750 with half-couplerwith 5 steps

1.00 x 1.57 28.0 40 2638.003 W 2 2 2 2

6 Stringer for modular stairway 1-step 0.30 2.4 50 5407.001 W 2 2 2 2

2-step 0.60 5.5 50 5407.002 W 2 2 2 2

3-step 0.90 8.0 20 5407.003 W 2 2 2 2

7 Guardrail for modular stairway 1-step 0.30 x 1.10 6.5 40 5407.011 W 2 2 2 2

2-step 0.60 x 1.10 14.0 25 5407.012 W 2 2 2 2

3-step 0.90 x 1.10 16.0 25 5407.013 W 2 2 2 2

8 Base collar for modular stairway, 0.26 mwith spigot

0.26 2.0 450 5407.021 W 2 2 2 2

9 Standard for modular stairway, 0.59 mwith spigot

0.59 3.1 250 5407.022 W 2 2 2 2

10 O-ledger LW, 0.90 m 0.90 3.4 50 2601.090 W 2 2 2 2

11 Lift-off preventer, with bolt 0.29 0.4 300 5407.030 W 2 2 2 2


®

Edition 04.2015Ref. No. 8116.252


Riser s = 16.00 cmTread a = 31.80 cmUndercut u = 0.20 cm

Side protection of the stage is provided by Handrails 2 or Guardrails with child safety features 3. The stairway stringer 5 fits exactly to the height of the Event decks. Thus it is always as top step. Depending on the podium height, the stairway can be extended with different stairway stringers.

6

7

8

911

10

Notice: In combination of different stairway stringers, the different stairway dimension must be pointed out. For further information, please see catalogue Allround Scaffolding..

Podium height: 2.40 mStairway: 2638.003 + 2638.008



Podium height: 0.90 mStairway: 2638.003

The artist entry to the stage is via the modular stairway. The construction kit comprises: Stringer for modular stairway, 1, 2 and 3 steps 6, Base collar 0.26 m 8 and O-ledger 0.90 m 10. If required, stairway guardrails are attached. The bolts needed for guardrail assembly are included with every stairway guardrail. The guardrails are not suitable for public areas.

13


Event systems – guardrails and stairways for stages Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 86

QEV

100

EV 10

4

1 4 + 5 1 Guardrail post for podium 1.64 13.8 100 5406.000 W 2 2 2 2

2 Handrail T13handrail height 1.00 m

1.00 7.9 40 5417.100 P 2

1.04 8.1 40 5417.104 P 2

2.00 15.0 40 5417.200 P 2

2.07 15.4 40 5417.207 W 2 2

2.57 18.7 40 5417.257 P 2 2

3 Guardrail with child safety feature T12Guardrail height 1.10 m.Connection elements height adjustable for use with Event or scaffolding decks.

1.00 19.8 25 5409.100 W 2

1.04 20.0 25 5409.104 W 2

1.57 25.8 25 5409.157 W 2

2.00 30.5 25 5409.200 W 2

2.07 30.8 25 5409.207 W 2 2

2.57 35.8 25 5409.257 W 2 2

2 3 4 Stairway guardrail 750 with child safety featurefor stairway stringer Pos. 5

1.00 x 1.57 22.0 25 2616.106 W 2 2 2 2

5 U-Stairway stringer 750 with half-couplerwith 5 steps

1.00 x 1.57 28.0 40 2638.003 W 2 2 2 2

6 Stringer for modular stairway 1-step 0.30 2.4 50 5407.001 W 2 2 2 2

2-step 0.60 5.5 50 5407.002 W 2 2 2 2

3-step 0.90 8.0 20 5407.003 W 2 2 2 2

7 Guardrail for modular stairway 1-step 0.30 x 1.10 6.5 40 5407.011 W 2 2 2 2

2-step 0.60 x 1.10 14.0 25 5407.012 W 2 2 2 2

3-step 0.90 x 1.10 16.0 25 5407.013 W 2 2 2 2

8 Base collar for modular stairway, 0.26 mwith spigot

0.26 2.0 450 5407.021 W 2 2 2 2

9 Standard for modular stairway, 0.59 mwith spigot

0.59 3.1 250 5407.022 W 2 2 2 2

10 O-ledger LW, 0.90 m 0.90 3.4 50 2601.090 W 2 2 2 2

11 Lift-off preventer, with bolt 0.29 0.4 300 5407.030 W 2 2 2 2

For further stairways and access assemblies, see Allround Scaffolding System Catalogue.

14

Universal base Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 10

0EV

104

1 1 Base beam,steel, hot-dip galvanized

0.86 13.0 5431.086 P 2

1.00 15.5 5431.100 P 2

1.04 16.1 5431.104 P 2

2.00 32.5 5431.200 P 2

2.07 33.7 5431.207 P 2 2

2 2 Base lattice beamsteel, hot-dip galvanized

0.86 x 0.50 38.2 5432.086 P 2

1.00 x 0.50 38.5 5432.100 P 2

1.04 x 0.50 39.1 5432.104 P 2

2.00 x 0.50 76.0 5432.200 P 2

2.07 x 0.50 76.7 5432.207 P 2 2

3 3 Truss-Transomsteel, hot-dip galvanized

0.86 27.8 5433.086 P 2

1.00 28.9 5433.100 P 2

1.04 29.0 5433.104 P 2

2.00 47.3 5433.200 P 2

2.07 48.6 5433.207 P 2 2

4 4 Base plate type 1steel, hot-dip galvanized,for H30V and H40V support with 32 drillings

0.41 x 0.41 25.0 5434.003 P 2 2 2

5 5 Base plate type 2steel, hot-dip galvanized,for H30V and H40V supportwith 16 drillings

0.41 x 0.41 25.0 5434.002 P 2 2 2

6 6 Special bolt with nutHZS 53 x 34

M16 x 60 2.0 5434.012 W 2 2 2

Universal base

Since the release of the new guidelines for temporary structures (EN 13814), the use of stage roofings ist not possible anymore without combining it with a podium of Layher.

With the universal base, you can connect roofs efficiently to the Layher podium. The speciality of this solution is, that it is possible to adjust almost every position of the supports contiuously.

If the base should be used for larger roofings, depending on the load bearing capacity, an additional support could be necessary.

2 Dead weight of the podium, can be charged – thus lower ballasting.

2 Forces, emitting by linkage, can be transmitted to the podium – thus lower ballasting.

2 Higher headroom, thanks to fixation points on deck level.

2 Quick assembly of the podium with the universal base and our well-known Allround Scaffolding.

2 Topographic problems at the place of action, can be solved easily.

2 Complete system, with stairways, ramps and guardrails available.

15


Universal base Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 10

0EV

104

1 1 Base beam,steel, hot-dip galvanized

0.86 13.0 5431.086 P 2

1.00 15.5 5431.100 P 2

1.04 16.1 5431.104 P 2

2.00 32.5 5431.200 P 2

2.07 33.7 5431.207 P 2 2

2 2 Base lattice beamsteel, hot-dip galvanized

0.86 x 0.50 38.2 5432.086 P 2

1.00 x 0.50 38.5 5432.100 P 2

1.04 x 0.50 39.1 5432.104 P 2

2.00 x 0.50 76.0 5432.200 P 2

2.07 x 0.50 76.7 5432.207 P 2 2

3 3 Truss-Transomsteel, hot-dip galvanized

0.86 27.8 5433.086 P 2

1.00 28.9 5433.100 P 2

1.04 29.0 5433.104 P 2

2.00 47.3 5433.200 P 2

2.07 48.6 5433.207 P 2 2

4 4 Base plate type 1steel, hot-dip galvanized,for H30V and H40V support with 32 drillings

0.41 x 0.41 25.0 5434.003 P 2 2 2

5 5 Base plate type 2steel, hot-dip galvanized,for H30V and H40V supportwith 16 drillings

0.41 x 0.41 25.0 5434.002 P 2 2 2

6 6 Special bolt with nutHZS 53 x 34

M16 x 60 2.0 5434.012 W 2 2 2

16

Event systems – leg insert platforms

Event systems – leg insert platforms Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 10

0EV

104

1 1 Event deck T10Aluminium frame. coated plywood , detachable plastic corners, threaded inserts for holding insert leg holders

1.00 x 2.00 28.3 10 5402.170 W 2

1.04 x 2.07 36.0 10 5402.180 W 2

0.86 x 2.07 27.5 10 5402.190 W 2

2 2 Event deck T10, squarefor equalizing bays, aluminium frame, coated plywood, detachable plastic corners, threaded inserts for holding insert leg holders

1.00 x 1.00 14.3 10 5402.175 W 2

1.04 x 1.04 19.3 10 5402.185 W 2

3 4 3 Clamp T10for coupling Event decks T7 / T10 (Pos. 1)

0.4 40 5403.506 W 2 2 2

4 Leg insert supportfor Event deck T10 (Pos. 1), incl. 4 screws, die-cast zinc, for holding Pos. 4

1.2 5402.010 W 2 2 2

5 5 Alu leg insert Q60 T13 with plastic slider

0.20 1.1 4 V 5415.021 P 2 2 2

0.40 2.2 4 V 5415.041 P 2 2 2

0.60 3.4 4 V 5415.061 P 2 2 2

0.80 4.5 4 V 5415.081 W 2 2 2

1.00 5.6 4 V 5415.101 W 2 2 2

7 6 Hinged foot for retrofit, with non-slip floor-protecting rubber underlay, Adjusting range 40 mm

0.3 6494.647 P 2 2 2

6 7 Insert leg connector, 2-wayfor aluminium insert legs Q60

1.1 5407.061 W 2 2 2

Leg insert supports 4 can be fitted into the corners of the T10 Event decks. These parts are fastened with two bolts, which are supplied. The insert leg holders are used to hold the Q60 aluminium legs 5. Insert leg connectors 7 are used to connect the insert legs to one another. Clamps 3 for Event decks connect the aluminium frames of the platforms to one another resulting in a smooth transition even under load.

The insert-leg kit is the ideal complement to the Layher Event System. This design is very economical for smaller platforms up to 1 m height. The assembly time and number of parts are lower than using an Allround support structure.

The permissible load of the platforms is 750 kg/m².Ideal for use in halls and rooms with sensitive floor coverings, thanks to the floor protecting and non-slip rubber pads, which are already integrated into the height-adjustable hinged feet 6.

17


Event systems – leg insert platforms Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 10

0EV

104

1 1 Event deck T10Aluminium frame. coated plywood , detachable plastic corners, threaded inserts for holding insert leg holders

1.00 x 2.00 28.3 10 5402.170 W 2

1.04 x 2.07 36.0 10 5402.180 W 2

0.86 x 2.07 27.5 10 5402.190 W 2

2 2 Event deck T10, squarefor equalizing bays, aluminium frame, coated plywood, detachable plastic corners, threaded inserts for holding insert leg holders

1.00 x 1.00 14.3 10 5402.175 W 2

1.04 x 1.04 19.3 10 5402.185 W 2

3 4 3 Clamp T10for coupling Event decks T7 / T10 (Pos. 1)

0.4 40 5403.506 W 2 2 2

4 Leg insert supportfor Event deck T10 (Pos. 1), incl. 4 screws, die-cast zinc, for holding Pos. 4

1.2 5402.010 W 2 2 2

5 5 Alu leg insert Q60 T13 with plastic slider

0.20 1.1 4 V 5415.021 P 2 2 2

0.40 2.2 4 V 5415.041 P 2 2 2

0.60 3.4 4 V 5415.061 P 2 2 2

0.80 4.5 4 V 5415.081 W 2 2 2

1.00 5.6 4 V 5415.101 W 2 2 2

7 6 Hinged foot for retrofit, with non-slip floor-protecting rubber underlay, Adjusting range 40 mm

0.3 6494.647 P 2 2 2

6 7 Insert leg connector, 2-wayfor aluminium insert legs Q60

1.1 5407.061 W 2 2 2

18

Event stands

FOR GETTING THE CROWD’S MONEY’S WORTH

No restrictions on comfort, no limits on dimensions and equipment,

no concessions to the location: Layher stands are always an excellent

“observation point”, just as required.

The Layher Event system: Stands for sitting and standing, all over the

world and meeting client requirements. Series manufacture and high

delivery readiness are our way to help you cut costs and achieve

economic success; and tailor-made special solutions whenever necessary

are our strengths.

The whole Layher Event-System bases on the proven Allround Scaffolding

System. Thus makes investions even more economical, because the

material can be used for lots of different kinds of use.

LAYHER EVENT STANDS

2 Standard solutions

Series material, rapid availability.

2 Substructure Allround

High load-bearing capacity, rapid erection and dismantling, flexible

assembly, choice of accessories.

2 Handy components

Easy to transport and store, palletizable.

2 Special design

for individualized problem solutions.


20

Event stands – basic components and guardrails for stands

Event stands – basic components and guardrails for stands Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 86

QEV

100

EV 10

4

1 2 1 Stand element1-step

1.00 x 0.25 6.6 40 5401.010 W 2

1.04 x 0.25 6.7 40 5401.020 W 2

2 Stand element2-step

1.71 x 0.33 10.5 30 5401.030 W 2 2

4 3 5 3 Intermediate step0.30 x 0.12 x L, with 2 half coupler

L = 1.00 8.4 5402.110 P 2 2

L = 1.25 10.5 5402.130 P 2 2

4 Guardrail standard, 0.96 mwith bottom mounted spigot and 2 cutaway rosettes

0.96 5.5 20 5405.045 W 2 2 2 2

6

5 Lift-off preventer for stand element

0.10 0.05 5403.501 W 2 2 2 2

7 6 Lift-off preventer for steel decks 0.86 1.6 5403.007 W 2 2

Bolt M10 x 70 with nut 3.5 50 V 5403.009 W 2 2

7 Steel deck support 0.10 0.4 5403.006 W 2 2

8 Side guardrail T122-step

2.00 x 1.10 32.2 25 5410.201 P 2

2.07 x 1.10 32.5 25 5410.204 W 2


2.57 x 1.10 35.2 25 5410.301 P 2 2

10 Side end guardrail T122-step

2.00 x 1.10 30.4 25 5410.202 P 2

2.07 x 1.10 30.7 25 5410.206 W 2


2.57 x 1.10 34.3 25 5410.302 P 2 2

12 Corner guardrail, top Steel

1.10 x 0.28 11.2 40 5410.303 W 2 2 2 2

EV 86, 166 mmEV 100/EV 104, 250 mm

EV 100/EV 104

The Stand element, 1-step 1 with a standard rise of 250 mm is used for the Event systems EV 100 and EV 104.

The Stand element, 2-step 2 is used for the Event system EV 86.

When Event decks are used, the Lock against lift-off 5 is required to prevent the Event decks from lifting off and tilting.

Alternatively, conventional steel decks can also be used, which is to be recommended especially for outdoor events. Here the Lock against lift-off ST 86 6 and the Steel deck support 7 are used.

The Guardrail standard 0.96 m 4 with the bottom mounted spigot, is used to guide the Allround standards out of the substructure. For side guardrails, however, this standard must be additionally reinforced.

The components shown here are showcase. For the different stand variants, showing in table on page 7, further stand components are available. These are stand elements, intermediate steps, guardrails and guardrail posts for each type of stand.

Side guardrails and guardrail posts EV 100/EV 104, rise 250 mm

Guardrail posts are dependent on the stand system – upon request

11

12

9

10

12

8

Side guardrails and guardrail posts EV 86, rise 166 mm

21


Event stands – basic components and guardrails for stands Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 86

QEV

100

EV 10

4

1 2 1 Stand element1-step

1.00 x 0.25 6.6 40 5401.010 W 2

1.04 x 0.25 6.7 40 5401.020 W 2

2 Stand element2-step

1.71 x 0.33 10.5 30 5401.030 W 2 2

4 3 5 3 Intermediate step0.30 x 0.12 x L, with 2 half coupler

L = 1.00 8.4 5402.110 P 2 2

L = 1.25 10.5 5402.130 P 2 2

4 Guardrail standard, 0.96 mwith bottom mounted spigot and 2 cutaway rosettes

0.96 5.5 20 5405.045 W 2 2 2 2

6

5 Lift-off preventer for stand element

0.10 0.05 5403.501 W 2 2 2 2

7 6 Lift-off preventer for steel decks 0.86 1.6 5403.007 W 2 2

Bolt M10 x 70 with nut 3.5 50 V 5403.009 W 2 2

7 Steel deck support 0.10 0.4 5403.006 W 2 2


2.00 x 1.10 32.2 25 5410.201 P 2

2.07 x 1.10 32.5 25 5410.204 W 2


2.57 x 1.10 35.2 25 5410.301 P 2 2


2.00 x 1.10 30.4 25 5410.202 P 2

2.07 x 1.10 30.7 25 5410.206 W 2


2.57 x 1.10 34.3 25 5410.302 P 2 2

12 Corner guardrail, top Steel

1.10 x 0.28 11.2 40 5410.303 W 2 2 2 2

22

Event stands – benches and bucket seats

Event stands – benches and bucket seats Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 86

QEV

100

EV 10

4

1 + 2 1 Benchanodised aluminium, coated plywood

1.57 x 0.30 7.2 5623.157 P 2 2

2.00 x 0.30 9.4 60 5623.200 W 2

2.07 x 0.30 9.5 60 5623.207 W 2 2

2.57 x 0.30 11.7 60 5623.257 W 2

2 Bench endanodised aluminium, coated plywood

0.06 x 0.30 0.5 5624.000 W 2 2 2 2

3a3b3c3d3e

3a Novanta bucket seat, blueUV-protected and flame-retardant

0.40 x 0.43 1.7 120 5408.021 W 2 2 2 2

3b3c

Plug, left, bluePlug, right, blue

0.2 20 V 5408.026 W 2 2 2 2

0.2 20 V 5408.027 W 2 2 2 2

3d Number plate, w/o lettering, white 0.2 20 V 5408.025 W 2 2 2 2

3e Assembly-Set for 20 bucket seatsexisting of 40 bolts M8 x 40, 40 nuts and 40 washers

1.2 120 5408.007 W

4 + 5 4 Bench, with holesfor Novanta bucket seats

1.57 x 0.30 7.2 60 5408.157 P 2 2

2.00 x 0.30 9.4 60 5408.200 P 2

2.07 x 0.30 9.5 60 5408.207 W 2 2

2.57 x 0.30 11.7 60 5408.257 W 2

5 Allround wedgeSteel, for securing bench, without rivets

0.14 3.3 25 V 6494.916 2 2 2 2

13.0 100 V 6494.918 W 2 2 2 2

6 7 8 6 Allround wedge, short, 90 mmwithout holes, for securing bench at edge of stand

0.09 1.0 10 V 6494.965 W 2 2 2 2

9 10 7 Bench adaptor for rise 16,70 cmfor rise 25,00 cm

0.42 3.7 350 5406.010 W 2 2

0.34 3.4 350 5406.015 W 2 2

8 Seat support with rosettefor bottom rows

0.34 4.0 300 5619.000 W 2 2 2 2

9 Tip-up seat, blueUV-protected and flame-retardant

0.42 x 0.19 3.2 on request 2 2 2 2

10 Aluminium frame for tip-up seatssuitable for all inclinations

1.04 5.8 on request 2 2 2 2

1.50 7.4 on request 2 2 2 2

1.57 7.6 on request 2 2 2 2

2.00 9.4 on request 2 2 2 2

2.07 9.7 on request 2 2 2 2112.57 11.8 on request 2 2 2 2

11 Adapter for frame for tip-up seats suitable for all inclinations

0.19 x 0.10 3.0 on request 2 2 2 2

You can choose the seating to suit the application, but also to suit your specific conditions. There is a choice of benches, bucket seats and tip-up seats.

The Bench 1 is 0.30 m wide and comprises anodised aluminium stiles and smooth-coated plywood.

Benches are secured with wedges: Short wedges 6 are needed at the edge of the stand. Bench ends 2 are fitted at the access to the stand.

Novanta bucket seats 3a can be fastened to the benches. We recommend benches with predrilled holes here. The standard Novanta bucket seats are dark blue, UV-protected and flame-retardant.

The assembly material comprises per seat:2 bolts with square neck2 washers2 nuts1 plug, left1 plug, rightNumber plate without lettering, white.

Alternatively, your own chairs can be placed on the Event stand.

The first row of seat is formed by the Seat support with rosette 8.

B

23


Event stands – benches and bucket seats Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 86

EV 86

QEV

100

EV 10

4

1 + 2 1 Benchanodised aluminium, coated plywood

1.57 x 0.30 7.2 5623.157 P 2 2

2.00 x 0.30 9.4 60 5623.200 W 2

2.07 x 0.30 9.5 60 5623.207 W 2 2

2.57 x 0.30 11.7 60 5623.257 W 2

2 Bench endanodised aluminium, coated plywood

0.06 x 0.30 0.5 5624.000 W 2 2 2 2

3a3b3c3d3e

3a Novanta bucket seat, blueUV-protected and flame-retardant

0.40 x 0.43 1.7 120 5408.021 W 2 2 2 2

3b3c

Plug, left, bluePlug, right, blue

0.2 20 V 5408.026 W 2 2 2 2

0.2 20 V 5408.027 W 2 2 2 2

3d Number plate, w/o lettering, white 0.2 20 V 5408.025 W 2 2 2 2

3e Assembly-Set for 20 bucket seatsexisting of 40 bolts M8 x 40, 40 nuts and 40 washers

1.2 120 5408.007 W

4 + 5 4 Bench, with holesfor Novanta bucket seats

1.57 x 0.30 7.2 60 5408.157 P 2 2

2.00 x 0.30 9.4 60 5408.200 P 2

2.07 x 0.30 9.5 60 5408.207 W 2 2

2.57 x 0.30 11.7 60 5408.257 W 2

5 Allround wedgeSteel, for securing bench, without rivets

0.14 3.3 25 V 6494.916 2 2 2 2

13.0 100 V 6494.918 W 2 2 2 2

6 7 8 6 Allround wedge, short, 90 mmwithout holes, for securing bench at edge of stand

0.09 1.0 10 V 6494.965 W 2 2 2 2

9 10 7 Bench adaptor for rise 16,70 cmfor rise 25,00 cm

0.42 3.7 350 5406.010 W 2 2

0.34 3.4 350 5406.015 W 2 2

8 Seat support with rosettefor bottom rows

0.34 4.0 300 5619.000 W 2 2 2 2

9 Tip-up seat, blueUV-protected and flame-retardant

0.42 x 0.19 3.2 on request 2 2 2 2

10 Aluminium frame for tip-up seatssuitable for all inclinations

1.04 5.8 on request 2 2 2 2

1.50 7.4 on request 2 2 2 2

1.57 7.6 on request 2 2 2 2

2.00 9.4 on request 2 2 2 2

2.07 9.7 on request 2 2 2 2112.57 11.8 on request 2 2 2 2

11 Adapter for frame for tip-up seats suitable for all inclinations

0.19 x 0.10 3.0 on request 2 2 2 2

24

Truss systems

VISUALLY ATTRACTIVE, LIGHTWEIGHT AND STABLE

The Layher Truss system contains 3-chord and 4-chord transoms of

aluminium. They are available as H30 and H40 series.

The Layher Truss system is developed for lightweight to intermediate-

heavy structures, which are mainly used in the exhibition sector. They are

characterised by very high stability, compactness, versatility and very low

operating weight. The installation is very simple, thanks to the direction-

independent framework.

LAYHER TRUSS SYSTEMS

2 Maximum load-bearing capacity

Outstanding load-bearing values yet a low degree of sag.

2 Compatibility

Layher truss systems are compatible both with many other truss

systems and with Layher Allround® equipment.

2 Maximum quality

Durable and value stable thanks to highest production quality.


25


ENORMOUSLY BEARING. HUGE SPANS. FOR DIFFERENT SCOPES OF APPLICATION

Constructions, which are made to carry high loads and however must be

easy and fast to assembly, need well-thought and strong components.

Layher offers with the new steel truss the right tools for that challenge.

LAYHER STEEL TRUSS SYSTEMS

2 Attractive outer dimensions.

2 High load-bearing capacity.

2 Large spans.

2 Quick assembly thanks to well-known fork-connectors.

26

Alu truss systems

Order the catalogue

rolling towers and ladders

LAYHER LADDERS & STAIRSLAYHER ROLLING TOWERS

CATALOGUE

Edition 04.2015Ref. No. 8118.225


Alu truss systems Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

1 1 Truss H30D, aluminium straight, 3-chord, external dimension 287 mm

0.25 x 0.26 x 0.29 2.0 5718.025 P0.50 x 0.26 x 0.29 3.0 5718.050 P0.71 x 0.26 x 0.29 3.9 5718.071 P0.75 x 0.26 x 0.29 4.1 5718.075 P1.00 x 0.26 x 0.29 5.1 5718.100 P1.50 x 0.26 x 0.29 7.4 5718.150 P2.00 x 0.26 x 0.29 9.5 5718.200 P2.50 x 0.26 x 0.29 11.7 5718.250 P3.00 x 0.26 x 0.29 13.8 5718.300 P3.50 x 0.26 x 0.29 15.6 5718.350 P4.00 x 0.26 x 0.29 22.3 5718.400 P4.50 x 0.26 x 0.29 27.5 5718.450 P5.00 x 0.26 x 0.29 32.5 5718.500 P

2 2 Truss H30V, aluminiumstraight, 4-chord, external dimension 287 mm


3 3 Truss H40D, aluminiumstraight, 3-chord, external dimension 387 mm




5a 5b 5c 5d 5abcdefgh

Truss corners H30D, aluminium2-way 90 degree2-way 90 degree2-way 90 degree3-way 90 degree3-way 90 degree4-way T-piece4-way T-piece4-way cross

0.50 x 0.30 x 0.50 3.9 5720.003 P0.50 x 0.30 x 0.50 3.8 5720.006 P0.50 x 0.30 x 0.50 4.3 5720.007 P0.50 x 0.50 x 0.50 6.0 5720.012 P

5e 5f 5g 5h 0.50 x 0.50 x 0.50 6.0 5720.013 P0.71 x 0.50 x 0.50 7.6 5720.014 P0.71 x 0.50 x 0.50 7.6 5720.015 P0.71 x 0.30 x 0.71 7.6 5720.016 P

The Layher Truss system contains 3-chord and 4-chord transoms of aluminium. They are available as H30 and H40 series.

The Layher Truss system is developed for lightweight to intermediate-heavy structures, which are mainly used in the exhibition sector. They are characterised by very high stability, compactness, versatility and very low operating weight. The installation is very simple, thanks to the direction-independent framework.

During the assembly of many truss structures, ladders and rolling towers are a constant campanion.

Also therefore, Layher is your dependable partner.

27



Weight approx. [kg]

PU[pcs.]

Ref. No.

1 1 Truss H30D, aluminium straight, 3-chord, external dimension 287 mm




3 3 Truss H40D, aluminiumstraight, 3-chord, external dimension 387 mm






0.50 x 0.30 x 0.50 3.9 5720.003 P0.50 x 0.30 x 0.50 3.8 5720.006 P0.50 x 0.30 x 0.50 4.3 5720.007 P0.50 x 0.50 x 0.50 6.0 5720.012 P

5e 5f 5g 5h 0.50 x 0.50 x 0.50 6.0 5720.013 P0.71 x 0.50 x 0.50 7.6 5720.014 P0.71 x 0.50 x 0.50 7.6 5720.015 P0.71 x 0.30 x 0.71 7.6 5720.016 P

28

Alu truss systems


Weight approx. [kg]

PU[pcs.]

Ref. No.

1a 1b 1c 1abcdef

Truss corners H30D, aluminium2-way 90 degree3-way 90 degree4-way cross3-way T-piece4-way T-piece5-way

0.50 x 0.30 x 0.50 5.3 5723.003 P

0.50 x 0.50 x 0.50 6.8 5723.012 P

0.71 x 0.30 x 0.71 10.2 5723.016 P

0.71 x 0.30 x 0.50 8.1 5723.017 P1d 1e 1f 0.71 x 0.50 x 0.50 10.1 5723.020 P

0.71 x 0.50 x 0.71 11.9 5723.024 P



0.60 x 0.40 x 0.60 5.1 5738.003 P

0.60 x 0.40 x 0.60 4.8 5738.006 P

0.60 x 0.40 x 0.60 5.8 5738.007 P

0.60 x 0.60 x 0.60 7.7 5738.012 P

0.60 x 0.60 x 0.60 7.7 5738.013 P2e 2f 2g 2h 0.90 x 0.60 x 0.60 10.2 5738.014 P

0.90 x 0.60 x 0.60 10.2 5738.015 P

0.80 x 0.40 x 0.80 9.4 5738.016 P

3a 3b 3c 3abcdef

Truss corners H40V, aluminium2-way 90 degree3-way 90 degree4-way cross3-way T-piece4-way T-piece5-way

0.60 x 0.40 x 0.60 7.0 5741.003 P

0.60 x 0.60 x 0.60 9.2 5741.012 P

0.80 x 0.40 x 0.80 12.8 5741.016 P

0.80 x 0.40 x 0.60 10.5 5741.017 P3d 3e 3f 0.80 x 0.60 x 0.60 12.8 5741.020 P

0.80 x 0.60 x 0.80 15.1 5741.024 P

4 4a 4b 4ab

Box Corner H30V, aluminiumAttachment SAttachment L

0.29 x 0.29 x 0.29 9.8 5714.030 P

0.105 x 0.29 x 0.29 1.3 5714.031 P

0.21 x 0.29 x 0.29 3.3 5714.032 P

5 5a 5b 5ab


0.39 x 0.39 x 0.39 12.1 5732.030 P

0.105 x 0.39 x 0.39 1.5 5732.031 P

0.21 x 0.39 x 0.39 3.3 5732.032 P

6a 6b 6ab

Base plate H30, aluminium3-chord H30D4-chord H30V

0.33 x 0.30 1.0 5701.072 P

0.33 x 0.33 1.7 5701.073 P

7a 7b 7ab


0.43 x 0.38 1.6 5701.077 P

0.43 x 0.43 2.9 5701.078 P

8a 8b 8c 8abc

Connection partsConic connectorConic boltSecuring pin

0.09 0.2 5701.020 W

0.07 0.0 5701.023 W

0.06 0.0 5701.007 W

9 10 9 Conic bolt with nut M8 0.07 0.1 5701.024 W

10 Conic half connector with thread M12 0.04 0.1 5701.034 W

29



Weight approx. [kg]

PU[pcs.]

Ref. No.

1a 1b 1c 1abcdef

Truss corners H30D, aluminium2-way 90 degree3-way 90 degree4-way cross3-way T-piece4-way T-piece5-way

0.50 x 0.30 x 0.50 5.3 5723.003 P

0.50 x 0.50 x 0.50 6.8 5723.012 P

0.71 x 0.30 x 0.71 10.2 5723.016 P

0.71 x 0.30 x 0.50 8.1 5723.017 P1d 1e 1f 0.71 x 0.50 x 0.50 10.1 5723.020 P

0.71 x 0.50 x 0.71 11.9 5723.024 P



0.60 x 0.40 x 0.60 5.1 5738.003 P

0.60 x 0.40 x 0.60 4.8 5738.006 P

0.60 x 0.40 x 0.60 5.8 5738.007 P

0.60 x 0.60 x 0.60 7.7 5738.012 P

0.60 x 0.60 x 0.60 7.7 5738.013 P2e 2f 2g 2h 0.90 x 0.60 x 0.60 10.2 5738.014 P

0.90 x 0.60 x 0.60 10.2 5738.015 P

0.80 x 0.40 x 0.80 9.4 5738.016 P

3a 3b 3c 3abcdef

Truss corners H40V, aluminium2-way 90 degree3-way 90 degree4-way cross3-way T-piece4-way T-piece5-way

0.60 x 0.40 x 0.60 7.0 5741.003 P

0.60 x 0.60 x 0.60 9.2 5741.012 P

0.80 x 0.40 x 0.80 12.8 5741.016 P

0.80 x 0.40 x 0.60 10.5 5741.017 P3d 3e 3f 0.80 x 0.60 x 0.60 12.8 5741.020 P

0.80 x 0.60 x 0.80 15.1 5741.024 P

4 4a 4b 4ab


0.29 x 0.29 x 0.29 9.8 5714.030 P

0.105 x 0.29 x 0.29 1.3 5714.031 P

0.21 x 0.29 x 0.29 3.3 5714.032 P

5 5a 5b 5ab


0.39 x 0.39 x 0.39 12.1 5732.030 P

0.105 x 0.39 x 0.39 1.5 5732.031 P

0.21 x 0.39 x 0.39 3.3 5732.032 P

6a 6b 6ab


0.33 x 0.30 1.0 5701.072 P

0.33 x 0.33 1.7 5701.073 P

7a 7b 7ab


0.43 x 0.38 1.6 5701.077 P

0.43 x 0.43 2.9 5701.078 P

8a 8b 8c 8abc

Connection partsConic connectorConic boltSecuring pin

0.09 0.2 5701.020 W

0.07 0.0 5701.023 W

0.06 0.0 5701.007 W

9 10 9 Conic bolt with nut M8 0.07 0.1 5701.024 W

10 Conic half connector with thread M12 0.04 0.1 5701.034 W

30

Steel truss systems

Tower Truss Maxi Truss

Span [m] perm. line load p [kg/m]

Bending [cm]

of perm. p

perm. single load F [kg]

Bending [cm]

of perm. F

perm. single load in third

points F1 [kg]

Bending [cm]

of perm. F1

2 5865 0.1 11729 0.1 5865 0.1

4 2914 0.3 8210 0.3 5827 0.4

6 1804 0.9 5411 0.7 4059 1.0

8 998 1.6 3993 1.3 2995 1.7

10 626 2.5 3127 2.0 2345 2.6

12 423 3.5 2538 2.8 1903 3.6

14 301 4.6 2106 3.7 1579 4.7

16 222 5.7 1773 4.6 1329 5.9

18 167 6.9 1505 5.5 1129 7.2

20 128 8.1 1284 6.5 963 8.4

22 100 9.2 1096 7.4 822 9.6

24 78 10.2 933 8.1 700 10.6

26 61 11.0 789 8.8 592 11.4

28 47 11.5 661 9.2 496 11.9


Bending [cm]

of perm. p


Bending [cm]

of perm. F


points F1 [kg]

Bending [cm]

of perm. F1

2 5425 0.1 8676 0.1 5425 0.1

4 2147 0.7 4294 0.5 3220 0.7

6 938 1.5 2813 1.2 2110 1.6

8 514 2.6 2058 2.1 1543 2.7

10 319 3.9 1593 3.1 1195 4.1

12 212 5.4 1273 4.3 955 5.6

14 148 7.0 1036 5.6 777 7.3

16 106 8.6 851 6.9 638 8.9

18 78 10.1 700 8.0 525 10.4

20 57 11.3 574 9.0 430 11.7

22 42 12.2 465 9.8 349 12.6

24 31 12.6 369 10.1 277 13.0

26 22 12.3 284 9.8 213 12.7

28 15 11.1 206 8.9 155 11.6

0

1.000

2.000

3.000

4.000

5.000

6.000

7.000

8.000

9.000

10.000

2 4 6 8 10 12 14 16 18 20 22 24 26 28

zul. vert. Streckenlast p [kN/m]

zul. Einzellast F [kN/m]

zul. Punktlast bei 2 Drittelpunkten F [kN/m]

Span [m]

p [kg/m]F, F

1 [kg]

0

2.000

4.000

6.000

8.000

10.000

12.000

14.000

2 4 6 8 10 12 14 16 18 20 22 24 26 28




Span [m]

p [kg/m]F, F

1 [kg]

1 2 3 4 5 + 6 Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

1 Tower-Truss, steel, hot-dip galvanizedUsable for roofings as vertical support for constructions of Maxi-Truss, as ground support, for advertisment signs or cable bridges, Use with bolt dia. 15.80 mm and spins clip

299 x 299Axial dimensions

on request

2 Maxi-Truss, steel, hot-dip galvanizedUsable for roofings as main transom, as ground support, for advertisment signs or cable bridges, Use with bolt dia. 15.80 mm and spins clip

569 x 569 Axial dimensions

on request

3 Nova-Truss, steel, hot-dip galvanizedUsable for roofings as vertical support for constructions of Super-Truss, as ground support, for advertisment signs or cable bridges, Use with bolt dia. 15.80 mm and spins clip


on request

7 + 8

4 Super-Truss, steel, hot-dip galvanizedUsable for roofings as main transom, as ground support, for advertisment signs or cable bridges, Use with bolt dia. 20.00 mm and spins clip


on request

5 Bolt, dia. 15.80 mm for Tower-Truss, Nova-Truss and Maxi-Truss

15.80 x 80 0.17 on request

6 Bolt, dia. 20.00 mm for Super-Truss

20 x 100 0.32 on request

7 Safety clip, 2.80 mm for Tower-Truss, Nova-Truss and Maxi-Truss

0.5 50 V 4905.001

8 Safety clip, 4 mm for Super-Truss

1.5 50 V 5905.001

perm. line load p [kg/m]


perm. single load in third points F

1 [kg]




1 [kg]

569 569

dia. 48,30

550 854

dia. 60,30

452 452

dia. 48,30

299 299

dia. 48,30

31


Nova Truss

The steel truss elements will be produced individually according to your requirements of length. Do not hesitate to ask us! We are pleased to help you.

Super Truss


Bending [cm]

of perm. p


Bending [cm]

of perm. F


points F1 [kg]

Bending [cm]

of perm. F1

14 877 3.3 6137 2.6 4603 3.4

16 659 4.2 5268 3.4 3951 4.4

18 509 5.2 4580 4.2 3435 5.4

20 402 6.3 4019 5.0 3015 6.5

22 323 7.4 3551 5.9 2663 7.7

24 263 8.5 3151 6.8 2363 8.8

26 216 9.6 2804 7.7 2103 10.0

28 179 10.7 2500 8.6 1875 11.1

30 149 11.8 2228 9.4 1671 12.2

32 124 12.7 1984 10.2 1488 13.2

34 104 13.5 1762 10.8 1322 14.0

36 87 14.2 1559 11.4 1169 14.7

38 72 14.7 1371 11.8 1028 15.2

40 60 15.0 1197 12.0 898 15.5


Bending [cm]

of perm. p


Bending [cm]

of perm. F


points F1 [kg]

Bending [cm]

of perm. F1

2 4724 0.1 9448 0.1 4724 0.1

4 2341 0.3 6497 0.4 4682 0.4

6 1421 1.0 4262 0.8 3196 1.0

8 781 1.7 3123 1.4 2342 1.8

10 485 2.6 2423 2.1 1817 2.7

12 324 3.6 1943 2.9 1457 3.8

14 227 4.7 1587 3.8 1191 4.9

16 164 5.8 1311 4.7 983 6.0

18 121 6.9 1086 5.5 814 7.1

20 90 7.8 898 6.2 673 8.1

22 67 8.5 736 6.8 552 8.8

24 50 8.9 595 7.1 446 9.2

26 36 8.9 468 7.1 351 9.3

28 25 8.4 354 6.7 266 8.7

0

1.000

2.000

3.000

4.000

5.000

6.000

7.000

8.000

9.000

10.000

2 4 6 8 10 12 14 16 18 20 22 24 26 28







1 [kg]

p [kg/m]F, F

1 [kg]

Span [m] 0

1.000

2.000

3.000

4.000

5.000

6.000

7.000

14 16 18 20 22 24 26 28 30 32 34 36 38 40







1 [kg]

p [kg/m]F, F

1 [kg]

Span [m]

1 2 3 4 5 + 6 Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

1 Tower-Truss, steel, hot-dip galvanizedUsable for roofings as vertical support for constructions of Maxi-Truss, as ground support, for advertisment signs or cable bridges, Use with bolt dia. 15.80 mm and spins clip

299 x 299Axial dimensions

on request

2 Maxi-Truss, steel, hot-dip galvanizedUsable for roofings as main transom, as ground support, for advertisment signs or cable bridges, Use with bolt dia. 15.80 mm and spins clip


on request

3 Nova-Truss, steel, hot-dip galvanizedUsable for roofings as vertical support for constructions of Super-Truss, as ground support, for advertisment signs or cable bridges, Use with bolt dia. 15.80 mm and spins clip


on request

7 + 8

4 Super-Truss, steel, hot-dip galvanizedUsable for roofings as main transom, as ground support, for advertisment signs or cable bridges, Use with bolt dia. 20.00 mm and spins clip


on request

5 Bolt, dia. 15.80 mm for Tower-Truss, Nova-Truss and Maxi-Truss

15.80 x 80 0.17 on request

6 Bolt, dia. 20.00 mm for Super-Truss

20 x 100 0.32 on request

7 Safety clip, 2.80 mm for Tower-Truss, Nova-Truss and Maxi-Truss

0.5 50 V 4905.001

8 Safety clip, 4 mm for Super-Truss

1.5 50 V 5905.001

32

QUICK AND CLEAN. FLEXIBLE FRONT-OF-HOUSE SOLUTIONS FROM LAYHER

The Layher FOH Tower Kit System provides you with the right solution

for your Front-Of-House applications. To meet the most frequently

encountered requirements, a total of 12 FOH Tower complete KITs are

available.

ONE SYSTEM – MANY VARIANTS

Thanks to the Kit System and Layher‘s flexible Allround equipment,

there are no limits placed on variation.

Whether it‘s a 2 or 3 bay width, with or without a projecting roof and

entrance, with 1, 2 or 3 stories. The Layher FOH Tower Kit System means

more possibilities. Typical for Layher!

LAYHER FOH TOWER KIT SYSTEM

2 Quick and easy assembly thanks to optimum use of material.

2 Neat and practically-minded design down to the last detail.

2 Each of the maximum of three levels is without a hindering

central support.

2 Complete enclosure using keder tarpaulins.

2 Very few special parts.

2 Calculated in accordance with the latest standard EN 13814.

2 Two inspection books available: 4.14 x 4.14 (4 x 4) & 6.21 x 4.14 (6 x 4).


FOH System, Roof and wall cladding

34

FOH System

FOH System Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 10

0EV

104

1 1 FOH beam 4.00 38.1 5573.010 W 2

4.14 38.6 5573.011 W 2

2 3 2 Event access deckwith aluminium hatch

1.00 x 2.00 33.5 5402.073 P 2

1.04 x 2.07 35.5 5402.083 P 2

3 Single step ladder with hook,10-steps, for item 7for storey height 2.50 m

2.70 x 0.45 7.7 5573.021 W 2 2

4 4 FOH rope holder set4 partsfor connection of the ballast bays

2.7 5573.002 W 2 2

5 + 6 Assembly Pos. 4 + 5 5 Rope fastenerfor ballast bays

1.20 1.3 5573.005 P 2 2

6 Rope fastenerfor roof stiffening

as HD 4.00 x 4.00 m 5.57 7.5 5573.003 P 2 2as HD 4.14 x 4.14 m 5.77 7.6 5573.004 P 2 2

Roof and wall cladding

Roof and wall cladding Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

7 - 9 10 7 Aluminium keder rail 2000 for side tarpaulins

2.50 3.8 4201.250 W

11 8 Aluminium keder rail 3000for roof tarpaulins

2.00 6.1 5574.200 P

3.00 9.2 5574.300 P

4.00 12.2 5574.400 P

5.00 15.3 5574.500 P

6.00 18.3 5574.600 W

9 Aluminium keder rail 9000 5.00 54.8 5577.500 P

6.00 65.8 5577.600 P

9.00 98.7 5577.900 P

10 Keder rail holder, rotatable 0.9 5573.000 W

11 Hinged attachment for Event roof 3.4 5573.001 W

12 12 Half-coupler, with plate 0.20 x 0.10 2.1 5573.030 P

The Layher FOH Tower Kit System provides you with the right solution for your Front-Of-House applications. To meet the most frequently encountered requirements, a total of 12 FOH Tower complete KITS are available.

One system – many variantsThanks to the Kit System and Layher’s flexible Allround equipment, there are no limits placed on variation.

Whether it’s a 2 or 3 bay width, with or without a projecting roof and entrance, with 1, 2, or 3 storeys

The proven keder rail 2000. Known for its low weight. Ideal for lightweight applications, particularly for wall coverings and scaffolding covers.

The keder rail 3000 – very strong yet light. It is perfectly suited for medium spans, as found for example in FOH and directing towers or in technical equipment and storage areas. The keder rail K3000 can also be used as a wall keder rail over large spans.

The keder rail 9000 is suitable as a heavy-duty marquee section for large and very large spans. Roofs and side coverings for large open-air stages can be constructed with this section, in addition to massive roofs for stands.

35


FOH System Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

EV 10

0EV

104

1 1 FOH beam 4.00 38.1 5573.010 W 2

4.14 38.6 5573.011 W 2

2 3 2 Event access deckwith aluminium hatch

1.00 x 2.00 33.5 5402.073 P 2

1.04 x 2.07 35.5 5402.083 P 2

3 Single step ladder with hook,10-steps, for item 7for storey height 2.50 m

2.70 x 0.45 7.7 5573.021 W 2 2

4 4 FOH rope holder set4 partsfor connection of the ballast bays

2.7 5573.002 W 2 2

5 + 6 Assembly Pos. 4 + 5 5 Rope fastenerfor ballast bays

1.20 1.3 5573.005 P 2 2

6 Rope fastenerfor roof stiffening

as HD 4.00 x 4.00 m 5.57 7.5 5573.003 P 2 2as HD 4.14 x 4.14 m 5.77 7.6 5573.004 P 2 2

Roof and wall cladding Pos. Description DimensionsL/H x W [m]

Weight approx. [kg]

PU[pcs.]

Ref. No.

7 - 9 10 7 Aluminium keder rail 2000 for side tarpaulins

2.50 3.8 4201.250 W

11 8 Aluminium keder rail 3000for roof tarpaulins

2.00 6.1 5574.200 P

3.00 9.2 5574.300 P

4.00 12.2 5574.400 P

5.00 15.3 5574.500 P

6.00 18.3 5574.600 W

9 Aluminium keder rail 9000 5.00 54.8 5577.500 P

6.00 65.8 5577.600 P

9.00 98.7 5577.900 P

10 Keder rail holder, rotatable 0.9 5573.000 W

11 Hinged attachment for Event roof 3.4 5573.001 W

12 12 Half-coupler, with plate 0.20 x 0.10 2.1 5573.030 P

36

Index

AAdapter for frame for tip-up seat 23

Allround wedge 23

Alu leg insert Q60 T13 17

Aluminium frame for tip-up seat 23

Alu truss system 26, 28

Assembly-Set 23

BBase beam 15

Base collar 10, 11, 12

Base collar for modular stairway 13

Base lattice beam 15

Base plate20 10, 1140 10, 1160 1160, solid 10H30 29H40 29type 1 15type 2 15

Basic component 10

Bench 22, 23

Bench adaptor 23

Bench end 22, 23

Boltdia. 15.80 mm 30dia. 20.00 mm 30M10 x 70 21

Box CornerH30V 29H40V 29

CClamp 16, 17

Conic bolt 29

Conic half connector 29

Connection part 29

Corner guardrail 21

EEvent access deck 35

Event deck 10

Event deck T10 11, 17square 11, 17

Event stage 8, 10

Event stands 18basic components and guardrails for stands 20benches and bucket seats 22

Event system 16

Event transom 10, 11

FFOH beam 35

FOH rope holder set 35

FOH System 32, 34

GGuardrail 12

Guardrail for modular stairway 13

Guardrail post for podium 13

Guardrail standard 20, 21

Guardrails with child safety features 12

Guardrail with child safety feature 13

HHalf-coupler 35

Handrail 12, 13

Hinged attachment 35

Hinged feet 16

Hinged foot 17

IInsert leg 16

Insert leg connector 16, 17

Intermediate step 21

KKeder rail 2000 34, 35

Keder rail 3000 34, 35

Keder rail 9000 34, 35

Keder rail holder 35

LLeg insert platform 16

Leg insert support 16, 17

Lift-off preventer 13, 21

Lift-off preventer for steel decks 21

Lock against lift-off 20

Lock against lift-off ST 86 20

MMaxi-Truss 30

NNovanta bucket seat 22, 23

Nova-Truss 30

Number plate 23

OO-ledger 12

O-ledger LW 13

PPlastic corner 10, 11

Plug 23

Podia 8

QQ60 aluminium leg 16

RRoof and wall cladding 32, 34

Rope fastenerfor ballast bays 35for roof stiffening 35

Rubber pad 10, 11

SSafety clip

2.80 mm 304 mm 30

Seating stand 7

Seat support with rosette 22, 23

Short wedge 22

Side end guardrail 21

Side guardrail 21

Single step ladder 35

Special bolt with nut 15

Square half-coupler 10, 11

Stage 6

Stairway 12

Stairway guardrail 750 13

Stairway stringer 12

Standard0.67 m 10, 111.17 m 10, 11

Standard for modular stairway 13

Stand element1-step 20, 212-step 20, 21

Stand system 6

Steel deck support 20, 21

Steel truss system 30

Stringer for modular stairway 12, 13

Super-Truss 30

TTension clasp 10

Tension clasp for transom 11

Tip-up seat 23

Tower-Truss 30

Transom support 10, 11

TrussH30D 27H30V 27H40D 27H40V 27

Truss cornersH30D 27, 29H40D 29H40V 29

Truss system 24

Truss-Transom 15

UUniversal base 14

U-Stairway stringer 750 13

Ref.

No.

811

1.22

7 Ed

ition

04.

2015

Wilhelm Layher GmbH & Co. KGScaffolding Grandstands Ladders

Ochsenbacher Strasse 5674363 Gueglingen-EibensbachGermany

Post Box 4074361 Gueglingen-EibensbachGermanyTelephone +49 (0) 71 35 70-0Telefax +49 (0) 71 35 70-2 65E-mail [email protected]

Proximity to the customer is a central factor behind Layher‘s success – geographically spea-king too. Wherever our customers need us, we will be there – with our advice, assistance and solutions.

Layher is your dependable partner with more than 70 years of experience. ”Made by Layher“ always means ”Made in Germany“ too – and that goes for the entire product range. Superb quality – and all from one source.

Headquarters in Eibensbach

Plant 2 in Gueglingen

SpeedyScaf

Allround Scaffolding

Event Systems

Accessories

Protective Systems

Shoring

Rolling Towers

Ladders

layher event systems catalogue · edition 04.2015 ref. no. 8111.227 quality management certified...

Documents