isometric views into orthographic views
DESCRIPTION
figures converted from iso to orthoTRANSCRIPT
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
CONVERSION OF ISOMETRIC VIEWS INTO ORTHOGRAPHIC VIEWS
1. Draw the elevation, plan, left and right side views of the part shown in the figure (All dimensions are in mm).
2. Draw the front view, top view, and right side view of the part shown in the figure (All dimensions are in mm).
3. Draw the front view, top view, left and right side views of the part shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
4. Draw the front view, top view, left and right side views of the part shown in the figure (All dimensions are in mm).
5. Draw the front view, top view, left and right side views of the part shown in the figure (All dimensions are in mm.)
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
6. Draw the elevation, plan, left and right side views of the part shown in the figure (All dimensions are in mm).
7. Draw the elevation, plan, side view of the part shown in the figure (All dimensions are in mm).
8. Draw the elevation, plan, and left side view of V-block as shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
9. Draw the front view, top view, left and right side views of the part shown in the figure (All dimensions are in mm).
10.Draw the front view, top view, left and right side views of the part shown in the figure (All dimensions are in mm).
11.Draw the front view, top view, left side view of the part shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
12.Draw the front view, top view, side view of the part shown in the figure (All dimensions are in mm).
13.Draw the front view, top view, side view of the part shown in the figure (All dimensions are in mm).
14.Draw the front view, top view, side view of the part shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
15.Draw the front view, top view, left side view of the part shown in the figure (All dimensions are in mm).
16. Draw the front view, top view, right side view of the part shown in the figure (All dimensions are in mm).
17.Draw the elevation, plan, left side view of the part shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
18.Draw the elevation, plan, and side view from left of the part shown in the figure (All dimensions are in mm).
19.Draw the elevation, plan, and side view of the part shown in the figure (All dimensions are in mm).
20.Draw the elevation, plan, and side view of the part shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
21.Draw the elevation, plan, and side view of the part shown in the figure using Third-angle projection. (All dimensions are in mm).
22.Draw the elevation, plan, and side view from right of the part shown in the figure (All dimensions are in mm).
23.Draw the elevation, plan, and side view of the part shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
24.Draw the elevation, plan, and side view from right of the part shown in the figure (All dimensions are in mm).
25.Draw the elevation, plan, and side view from right of the part shown in the figure (All dimensions are in mm).
26.Draw the elevation, plan, and side view of the part shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
27.Draw the elevation, plan, and side view of the part shown in the figure (All dimensions are in mm).
28.Draw the elevation, plan, and both side views of the part shown in the figure using third-angle projection. (All dimensions are in mm).
29.Draw the elevation, plan, and side view of the part shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
30.Draw the elevation, plan, and side view of the part shown in the figure (All dimensions are in mm).
31.Draw the elevation, plan, and both side views of the part shown in the figure using third angle projection. (All dimensions are in mm).
32.Draw the elevation, plan, and side view of the part shown in the figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
CONVERSION OF ORTHOGRAPHIC VIEWS INTO ISOMETRIC VIEWS
1. Draw the isometric view of a Door-Steps having three steps of 22cm tread and 15cm rise. The steps measure 75cm width wise.
2. Draw the isometric view of the ribbed angle plate, Shown in figure. All dimensions are in mm.
3. Draw the isometric view of the object whose orthographic projections are given in figure . All dimensions are in mm.
4. Draw the isometric view of the object whose orthographic projections are given in figure . All dimensions are in mm.
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
5. Draw the isometric view of the object whose orthographic projections are given in figure . All dimensions are in mm.
6. Draw the isometric view of the object whose orthographic projections are given in figure . All dimensions are in mm.
7. Draw the isometric view of the object whose orthographic projections are given in figure . All dimensions are in mm.
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
8. Draw the isometric view of the object whose orthographic projections are given in figure . All dimensions are in mm.
9. Draw the isometric view of the object whose orthographic projections are given in figure . All dimensions are in mm.
10.Draw the isometric view of the block, two views of which are shown in figure (All dimensions are in mm).
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
Draw the isometric view of the object whose orthographic projections are given in figure using Third-angle projection. All dimensions are in mm..
11.Draw the isometric view of the object whose orthographic projections are given in figure. All dimensions are in mm.
12.Draw the isometric view of the object whose orthographic projections are given in figure. All dimensions are in mm.
13.Draw the isometric view of the object whose orthographic projections are given in figure all dimensions are in mm.
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
14.Draw the isometric view of the object whose orthographic projections are given in figure all dimensions are in mm.
15.Draw the isometric view of the object whose orthographic projections are given in figure all dimensions are in mm.
16.Draw the isometric view of the object whose orthographic projections are given in figure all dimensions are in mm.
17.Draw the isometric view of the object whose orthographic projections are given in figure all dimensions are in mm.
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
18.Draw the isometric view of the object whose orthographic projections are given in figure all dimensions are in mm.
19.Draw the isometric view of the object whose orthographic projections are given in figure all dimensions are in mm.
20.Draw the isometric view of the object whose orthographic projections are given in figure all dimensions are in mm.
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
21.Draw the isometric view of the object whose orthographic projections are given in figure all dimensions are in mm.
22.Draw the isometric view of the object whose orthographic projections are given in figure using Third-angle projection. All dimensions are in mm.
23.Draw the isometric view of the object whose orthographic projections are given in figure using Third-angle projection. All dimensions are in mm.
LOYOLA INSTITUE OF TECHNOLOGY AND MANAGEMENT
DEPARTMENT OF MECHANICAL ENGINEERING
24.Draw the isometric view of the object whose orthographic projections of the pentagonal pyramid shown in figure.
25.Draw the isometric view of the object whose orthographic projections of the frustum of the cone shown in figure.
26.Draw the isometric projection of a Frustum of hexagonal pyramid, side of base 30 mm the side of top face 15mm of height 50 mm.