instructions to prepare a paper for...
TRANSCRIPT
Asian Workshop on Aircraft Design Education
AWADE 2018Nanjing University of Aeronautics and Astronautics (NUAA), 14-17 October 2018
http://aircraftdesign.nuaa.edu.cn/AWADE/index.html
INSTRUCTIONS TO PREPARE A FULL-LENGTH PAPER FOR THE AWADE WORKSHOP
Erasmo Carrera1, Valery Komarov2
1 – Politecnico di TorinoDepartment of Mechanical and Aerospace Engineering
Corso Duca degli Abruzzi, 2410129, Torino, Italy
e-mail: [email protected], web page: http://www.mul2.com
2 – Samara State UniversityDepartment of Aircraft Engineering
Moskovskoe sh., 34.443086, Samara, Russia,
e-mail: [email protected]
Key words: Modeling, Experimental and numerical mechanics, Education process.
Abstract. This document provides information and instructions for preparing the full-length paper for the AWADE2018 Workshop (14-17 October 2018, Nanjing University of Aeronautics and Astronautics, China)
1 INTRODUCTION
The paper should be written following the format of this template. Printed materials should be typed in editor not lower than MS Word, font Times New Roman, font size - 12, alignment - "in width" in A4 format.
The submission of the full-length paper is mandatory, and word file should be sent on address: [email protected] before September 1, 2018.
Each registered delegate can present no more than two papers.Further information can be found at the conference webpage:
http://aircraftdesign.nuaa.edu.cn/AWADE/index.html.
2 GENERAL SPECIFICATIONS
The paper must be written in English. The full-length paper must have a maximum length of 10 pages.
3 TITLE, AUTHORS, AFFILIATION, KEY WORDS
The first page must contain the Title, Author(s), Affiliation(s), and Key words. The Introduction must begin immediately below, following the format of this template.
First A. Author, Second B. Author
3.1 Title
The title should be written centered, in 14pt, boldface Times, all capital letters. It should be single spaced if the title is more than one line long.
3.2 Author
The author's name should include first name, middle initial and surname.
3.3 Key words
Please, write no more than six keywords.
4 FIGURES
All figures should be numbered consecutively and captioned, and should be embedded in the Paper.
Fig.1. Caption goes here
6 EQUATIONS
A displayed equation is numbered, using Arabic numbers in parentheses. It should be centered, leaving a 6pt space above and below to separate it from the surrounding text.
The following example is a single line equation:
Ax = b (1)
The next example is a multi-line equation:
Ax = b (2)
Сy = d
7 TABLES
All tables should be numbered consecutively and captioned.Table 1. Table example
C11 C12 C13C21 C22 C23C31 C32 C33C41 C42 C43C51 C52 C53
2
First A. Author, Second B. Author
8 FORMAT OF REFERENCES
References should be quoted in the text by numbers [1,2] and grouped together at the end of the paper in numerical order as shown in these instructions.
9 CONCLUSIONS
We look forward to receiving your papers for the collection of our seminar.
REFERENCES
[1] E. Carrera, S. Brischetto and P. Nali. Plates and Shells for Smart Structures: Classicaland Advanced Theories for Modeling and Analysis. John Wiley & Sons Ltd, 2011.
[2] V.M. Franco Correia, C.M. Mota Soares and C.A. Mota Soares. Refined models forthe optimal design of adaptive structures using simulated annealing. Composite Structures54(2-3), 161–167, 2001.
Authors
The First Author The Second Author
3
First A. Author, Second B. Author
Contact for any information: [email protected] [email protected]
Chairman of Technical Committee of AWADE 2018 Prof. Anatolii Kretov
4