Installation InstructionsFor Pre-Attached Rosettes & Short PlatesPassage and Privacy

Door Handing - Rosettes and Short Plates

With step-by-step Installation Pictograms & Drilling Template

Applies to: • Classic and Rope Rosettes• Cottage and Studio Short Plates

Tools Required: #2 Phillips Screwdriver (Not power tools)

Door handing is critical for Split-Finish, or Split-Design products. It’s also used to determine where the Interior and Exterior halves of the lockset are located on the door. And, it’s used to position the latch tongue in relation to the strike plate.

INSTALLATION RULES:

1) Lockset machine mounting screws are inserted from the inside.2) Privacy pin holes are next to the door side containing the latch.3) Latch tongues have a beveled side, and this side should contact

the curved end of the face plate, and curved end of the strike plate.(See *Latch Tongue Note on page 3.)

Inside of Door - The Inside of a door refers to the side of the door that faces the room. For example, for a bedroom door on a hallway, the Inside of the door would face the bedroom.

Outside of Door - The Outside of a door refers to the side of the door that faces away from the room. The Outside of a door is generally more visible to visitors, and therefore a rosette on this side of the door has no visible screws. For example, on a bedroom door, the Outside would face the hallway.

outside

To identify door handing, face door from the Outside.

outside

DOORS OPENING INWARD

Hinge is on the left.Door is Left Hand.

Hinge is on the left.Door is Left Hand.

Hinge is on the right.Door is Right Hand.

Hinge is on the right.Door is Right Hand.

To identify door handing, face door from the Outside.

DOORS OPENING OUTWARD

outsideoutside

Page 1 - PK177 04202017

Exte

rior

Hal

f of

Lock

set

Spin

dle

Spin

dle

Butt

on

Lock

ing

Mec

hani

sm(T

hrea

ded

Priv

acy-

Pin

Hol

e)

Priv

acy

Pin

Hol

e

Priv

acy

Pin

Ant

i-Rot

atio

nBl

ock

1-1/

2” M

achi

ne S

crew

s(1

-3/8

” thi

ck d

oors

), or

1-3/

4” M

achi

ne S

crew

s(1

-3/4

” thi

ck d

oors

)

Latc

h

Latc

h To

ngue

Strik

e Pl

ate

3/4”

Fla

t Hea

dW

ood

Scre

ws

Face

plat

eEmer

genc

yRe

leas

e H

ole

Inte

rior

Hal

f of

Lock

set

Expl

oded

Dra

win

g fo

r Pre

-Att

ache

d Ro

sett

e/Sh

ort P

late

s Pa

ssag

e/Pr

ivac

y

Priv

acy

Emer

genc

yRe

leas

e Ke

y

Page

2 -

PK17

7 0

4202

017

Passage/Privacy

Installation InstructionsFor Pre-AttachedRosettes and Short Plates

Tools Required: #2 Phillips Screwdriver (Not power tools)

Fits doors1-3/8” to 1-3/4” thick

Attach the strike plate to the door jambusing 3/4” long wood screws.

DoorJamb

Install Strike Plate

Door - Inside

Screw in the Privacy Pin

(Privacy Only)

Install Privacy Pin

Door - Inside

Install interior half of lockset with 1-1/2” machine screws (1-3/8” thick doors), or 1-3/4” machine screws (1-3/4” thick doors)

Install Interior Half of Lockset

Door - Inside

InstallExteriorHalf ofLockset

Emergency Release Hole(Privacy Only)

Push spindle buttondown and hold during

insertion

1

2 Insert

Spindle

InsertSpindle

Door - Inside

LatchTongue

* Latch Tongue Note

Bevel Side

Face Plate Curve

Strike Plate Curve

Threaded privacy hubgoes on theinside of thedoor.

Bevel side of latch tongue shouldcontact curved end of face plate,and curved end of strike plate.

Install latch and rotate the latch tongue to change handing.(See page 1 for handing)

Install anti-rotation block. Be certain the arrow is pointing to the edge of the door.

Install faceplate with 3/4” wood screws.

(Anti-Rotation Block)

Arrow

1

2

3

Door - Inside See Latch TongueNote in next panel

*

*

InstallLatch

For 2-3/8” Backset:

For 2-3/4” Backset:

BacksetInformation

NOTE:

DRILLING TEMPLATES ON SEPARATE INCLUDED SHEET

Page 3 - PK177 04202017

MEA

SURE

FRO

M T

HE

FLO

OR

TO T

HE

CEN

TER

OF

EXIS

TIN

G L

OCK

S, A

ND

USE

TH

IS D

ISTA

NCE

AS

THE

CEN

TER

OF

THE

DU

MM

Y M

OU

NT.

IF

THER

EA

RE N

O E

XIST

ING

LO

CKS,

PO

SITI

ON

TH

E D

UM

MY

MO

UN

T 36

” TO

38”

FRO

M T

HE

FLO

OR.

(2) F

OLD

TEM

PLAT

E A

LON

G D

OTT

ED L

INE,

AN

D P

OSI

TIO

N F

OLD

ON

TH

E ED

GE

OF

THE

DO

OR.

T

APE

TEM

PLAT

E TO

FA

CE O

F D

OO

R.

(3) B

EFO

RE D

RILL

ING

VER

IFY

THE

BACK

SET

OF

YOU

R EX

ISTI

NG

DO

ORS

IN Y

OU

R H

OU

SE. D

RILL

PIL

OT

HO

LES

USI

NG

A 7

/64”

DIA

MET

ER B

IT.

(4) I

NSE

RT T

HRE

E W

OO

D S

CREW

S,

SL

IDE

ROSE

TTE

OVE

R M

OU

NT,

AN

D S

CREW

-ON

KN

OB.

(5) I

NSE

RT H

EX S

CREW

S

A

ND

TIG

HTE

N.

FLO

OR

DU

MM

Y M

OU

NT

(1)

TEM

PLAT

E

EDG

E O

F D

OO

RFACE

OF

DO

OR

Page

4 -

PK17

7

0420

2017