index properties of rocks
TRANSCRIPT
![Page 1: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/1.jpg)
THE UNIVERSITY OF AZAD JAMMU AND KASHMIRSUBMITTED TO: PROF.YASIR SARFRAZ
SUBMITTED BY :GROUP 5TOPIC: TECHNIQUES FOR MEASUREMENT OF IN-SITU
STRESSESSESSION:2013 -2017SECTION : MORNING
INSTITUTE OF GEOLOGY
![Page 2: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/2.jpg)
INDEX PROPERTIES OF ROCK
Because of vast range in the properties of rocks &due to certain properties that are relatively easy to measure are valuable & may be designated index properties for rock specimens.
• POROSITY• DENSITY• SONIC VELOCITY• PERMEABILITY• STRENGTH
![Page 3: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/3.jpg)
1 Porosity identifies the relative proportion of solids and voids.2 Density adds the information about the minerals and grain
constituents. 3 The sonic velocity evaluate the degree of fissuring (planar
cracks in igneous & metamorphic rocks).4 Permeability evaluate the relative interconnection of pores.
5 Strength determine the present competency of rock fabric to bind the component together.
![Page 4: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/4.jpg)
PorosityPorosity is the ratio or fraction b/w the proportion of void spaces & the total spaces in the rock
n= vp /vt
Vp = volume of pores
Vt = total volume
Sedimentary rocks are formed by the accumulation of grains , rock fragments & shells.
Porosity varies from 0% to 90 % with 15% as a typical value for an average sandstone
Porosity generally decreases with age & depth below the surface.
A typical cambrian sandstone has 11% porosity & cretaceous sandstone has 34 % porosity
Chalk is most porous among all the rocks its porosity is 50%.
![Page 5: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/5.jpg)
Porosity can be determined from the following calculations
• Measured density• Measured water content after saturation in water
• Mercury content after saturation with mercury using pressure injector
• Measured solid volume & pore air volume using boyles law
![Page 6: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/6.jpg)
![Page 7: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/7.jpg)
DENSITYDensity is the mass per unit volume.Density = M/V
It is stated previously that the porosity of rock can be calculated from the knowledge of its weight density.Density tell about the porosity & permeability .At 20 °C in the rock the volume of water is 62.4 .If the percentage of different mineral can be estimated under a binocular microscope or from the thin section , the specific gravity of the part of the rock can be calculated as the weighted average of solid specific gravities of component grains & crystal.
![Page 8: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/8.jpg)
G = Specific gravity of component = volume percentage in the solid part of the
rock
The relationship b/w porosity &dry density is
![Page 9: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/9.jpg)
The dry density is related with wet density by relationship
W= water content of rock (dry weight basis)
Water content &porosity are related by
![Page 10: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/10.jpg)
In case of mercury content
Specific gravity of mercury =13.5
![Page 11: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/11.jpg)
![Page 12: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/12.jpg)
SONIC VELOCITYSonic velocity evaluate the degree of fissuring( planar cracks in igneous and metamorphic rock)
SONIC VELOCITY AS AN INDEX TO DEGREE OF FISSURING:The velocity with which stress waves are transmitted. First calculate the longitudinal wave velocity that the specimen would have,if it lacked pores or fissures.If the mineral composition is known longitudinal wave velocity can be calculated as
![Page 13: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/13.jpg)
Where the v1 is the longitudinal wave velocity in mineral constituent which have volume proportion C in the rock. Now measure the actual velocity of the longitudinal waves in the rock specimen & form the ratio
As a quality index define
Where np% is the porosity of non fissured rocks a percentage.
![Page 14: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/14.jpg)
![Page 15: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/15.jpg)
![Page 16: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/16.jpg)
PERMEABILITYPermeability evaluate the relative interconnection of pores.Fluid mechanics depend upon permeability.Shale is porous ,not permeable &fluid mechanics is not involvedSandstone is porous ,permeable & fluid mechanics is involved,
![Page 17: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/17.jpg)
STRENGTHStrength determine the present competency of rock fabric to bind the component together. Strength determination of rock usually required careful test setup & specimen preparation & result are highly sensitive to the method & style of loading.Strength index is now available using the point load test describe by “BROCH & FRANK”.
![Page 18: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/18.jpg)
Where P is the load of rupture & D is the distance b/w the point loads
Test are done on pieces of drill core at atleast 4 times as long as the diameter
![Page 19: Index properties of rocks](https://reader036.vdocuments.us/reader036/viewer/2022062903/58ed6fa91a28abdb228b45c1/html5/thumbnails/19.jpg)
THANK YOU