in-nt-1.2 - new features

7/28/2019 IN-NT-1.2 - New Features

1/11

New features of IN-NT sw V1.2 Page 1 of 11

IN-NT V1.2 New Features / ComAp May 2012 / IN-NT-1.2 - New Features.pdf

ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t

ComAp, spol. s r.o.Kundratka 2359/17180 00 Prague 8Czech Republic

Tel.: +420 246 012 111Fax: +420 246 316 647E-mail: [email protected]

Internet: http://www.comap.cz

1. Available firmware, archives, user texts and documentation

Package

.nca Package files

IN-NT-AMF-1.2.nca

IN-NT-MRS-1.2.nca

Firmware.nfw Firmware files .nca Package files

IN-NT-AMF-1.2nfw IN-NT-AMF-1.2.nca

IN-NT-MRS-1.2.nfw IN-NT-MRS-1.2.nca

Archives.ain Archive files .nca Package files

IN-NT-AMF-1.2.ain IN-NT-AMF-1.2.ncaIN-NT-MRS-1.2.ain IN-NT-MRS-1.2.nca

User texts.xml User texts files .nca Package files

NE-UserTexts.xml IN-NT-AMF-1.2.nca

NE-UserTexts.xml IN-NT-MRS-1.2.nca

DocumentationPDF files Description

IN-NT-AMF-1.2 - Reference Guide.pdf Manual for InteliNano NT AMF gen set controller

IN-NT-MRS-1.2 - Reference Guide.pdf Manual for InteliNano NT MRS gen set controllern

InteliNano-AMF-1.2 - Fast User Guide.pdf Fast user guide for InteliNano NT AMF gen set controller

InteliNano-MRS-1.2 - Fast User Guide.pdf Fast user guide for InteliNano NT MRS gen set controller

IN-NT-1.2 - New Features.pdf List of new features for software update


2/11



ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




2. Main changes in IN-NT 1.1

2.1 New setpoints

2.1.1 Light Tower Mode

This new setpoint is available in IntelNano AMF version only.

B08 Light Tower Mode

Units:

Step:

Range: 1,2

Default value: 1

This setpoint is available only when B06 AMF Functionis disabled. When this setpoint is enabled,the controller is switched to special operation mode. First screen was changed and generator voltagemeasurement is hides in this operation mode.

Setpoint code Value Meaning

E08 1 DisableE08 2 Enable

First main screen shows battery voltage, running hours and engine status (stop, starting/stopping,run) via symbol in light tower reflector (upper left corner).

Second screen shows all analog values which are available. (Oil Pressure, Coolant Temperature;Fuel Level and Battery Voltage)


3/11



ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




Last screen is event log.

2.1.2 Choke Time

E09 Choke Time

Units: seconds [s]

Step: 1 sRange: 0 3600 s

Default value: 0 s

Choke output timer is dedicated forChoke output. The timer is started on engine run.

Prestart Time

0 - 600 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Cranging Fail

Pause 8 s

Cranging Fail

Pause 8 sGen-set start failed

Starter Output

On

Off

TimeStart

Choke Output

On


4/11



ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




Prestart Time

0 - 600 s

Maximum

Cranking Time

0 - 60 s

On

Off

TimeStart

Engine run

Max. Stab. Time 7 sMin. Stab. Time

Starter Output

Stop

Choke Time

Choke Output

On

2.1.3 Minimal Stabilization Time

E10 Minimal Stabilization Time

Units: seconds [s]

Step: 1 s

Range: 1 300 s

Default value: 3 s

Delay:

Minimum time after reaching of defined level of RPM to the closing GCB.

Prestart Time

> 8 s

Maximum

Cranking Time

0 - 60 s

Gen-set start failed shutdown,

if the voltage or frequency are not in

the limit

On

Off

TimeStart

Engine run

Max. Stab. Time 7 sMin. Stab. TimeGen-set can be

loaded

Starter Output

Gen-set can be loaded

only when all running

condition are satisfied


5/11



ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




2.2 Setpoints changes

2.2.1 Connection Type

B04 Connection Type

Units:

Step:

Range: 1,2,3,4,5

Default value: 4

Generator winding connection.


B04 1 Mono PhaseB04 2 Split PhaseB04 3 3Ph3Wire

B04 4 3Ph4WireB05 5 Autodetect

Mono Phase: MONOPHASE,Single-phase measurement 1PH

Split Phase: DOUBLE DELTA Connection, Split Phase,Single-phase measurement 1PH

3Ph3Wire: DELTA Connection, 3 Phase without neutral - 3 Wires,Three phase delta measurement 3PD

3Ph4Wire: STAR Connection, 3 phases and neutral - 4 wires,

Three phase wye measurement 3PY

Autodetect:3Ph3Wire (Edison Delta) L1 >=100V; L1 =140Vor L3 >=100V; L3 =100VL2 >=100V

or L3 >=100V

Split Phase L1 >=100VL2 >=100V

or L3 >=100V L3 =100VL2


6/11



ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




2.3 New binary outputs

2.3.1 Choke

O13 Choke

The output is activated while engine is cranking and between cranking attempts. Choke Time (timer)will start on engine rune. The Choke output will close when Choke Time elapsed.

Prestart Time

0 - 600 s

Maximum

Cranking Time0 - 60 s

Maximum


Maximum


Cranging Fail

Pause 8 s

Cranging Fail

Pause 8 sGen-set start failed

Starter Output

On

Off

TimeStart

Choke Output

On

Prestart Time0 - 600 s MaximumCranking Time

0 - 60 s

On

Off

TimeStart

Engine run


Starter Output

Stop

Choke Time

Choke Output

On


7/11



ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




2.3.2 Glow Plugs

O14 Glow Plugs

This output is activated before each cranking procedure for Prestart Time but maximally for 8s!

Prestart Time

8 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Cranging Fail

Pause 8 s

Cranging Fail

Pause 8 s

Gen-set start failed

On

Off

Starter Output

TimeStart

Glow Plugs

Output On

Prestart Time

> 8 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Maximum

Cranking Time

0 - 60 s

Cranging Fail

Pause 8 s

Cranging Fail

Pause 8 s

Gen-set start

failed

On

Off

TimeStart

Glow Plugs

Output On

8 s

Starter Output


8/11



ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




Prestart Time

> 8 s

Maximum

Cranking Time

0 - 60 s

Gen-set start failed shutdown,

if the voltage or frequency are not in

the limit

On

Off

TimeStart

Engine run


Starter Output

8 s

Glow Plugs

Output On

2.4 Binary outputs changes

2.4.1 Stop Solenoid

O03 Stop Solenoid

This output is dedicated to control the stop solenoid (valve). The output closes when an engine stopcommand is received and remains active until the gen-set is stopped.

The engine is stopped if:

RPM < 2and

Generator voltage < 10Vand

Oil pressure < 3 Bar. (43 PSI)


9/11



ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




Fuel Solenoid is

opened

Gen-set stoped

On

Off

TimeStop

Engine run 10 s

Oil Pressure

Stop Solenoid

Output

Generator voltage

Cooling Time

D+

RPM / Frequency

Stop Time

Fuel Solenoidis opened

Gen-set stoped

On

Off

TimeStop

Engine run 10 s

Oil Pressure

Stop Solenoid

Output

Generator voltage

Cooling Time

D+

RPM / Frequency

Stop Time

Stop Fail Warning


10/11

New features of IN-NT sw V1.2Page 10 of

11


ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




2.5 Other changes

2.5.1 Outputs configuration

Binary outputs Fuel Solenoid and Stop Solenoid can be configured simultaneously to all output terminals

except terminal T04.

2.5.2 Hiding unused values

All unused analog or binary inputs/values (Low Fuel Level, Fuel Level Analog, Low Oil Pressure, OilPressure Analog, High Coolant Temperature, Coolant Temperature Analog) are hided removed fromthird screen.

2.5.3 Activity indications

Mains symbol on first screen will blink when mains is present and MCB is opened. Generator symbol willblink during engine start/stop and cooling procedure. Rotation in generator symbol will indicate engine run.

2.6 Solved problems

2.6.1 Oil Pressure value in US format

The problem with displayed Oil Pressure value in US format has been solved.

2.6.2 Zero Power Mode

The issue with Zero Power Mode, Battery Flat warning during Zero Power Mode and saving engine runninghour has been solved.


11/11

New features of IN-NT sw V1.2Page 11 of

11


ISO 9001 Certified

Com

Aps.r.o

.

QualityManagemen

t




3. Main changes in IN-NT 1.1

New starter disengage condition. Now you can choose if you want to use Low Oil Pressure binary input(signal) for starter disengagement or not. For this choice we add new setpoint.

E08 Oil Pressure Starter Disengagement

Units:

Step:

Range: 1,2

Default value: 1

When this setpoint is enabled, the controller will use Low Oil Pressure orOil Pressure Analogsignal for starter disengagement. Starter will disengaged when oil pressure reach starting oil pressure

or binary input Low Oil Pressure will be opened (Normally Open contact) or closed (NormallyClose contact).When is disabled then only RPM (frequency), generator voltage or D+ will be used for starterdisengagement.


E08 1 DisableE08 2 Enable

NOTE:This setpoint is available in IN-NT AMF and IN-NT MRS models.

in-nt-1.2 - new features

Documents