im10044 vantage 575cummins - welding equipment rental · special precautions should be used to...

VANTAGE 575 CUMMINS

OPERATOR’S MANUAL

IM10044March, 2010

Safety Depends on YouLincoln arc welding and cuttingequipment is designed and builtwith safety in mind. However,your overal l safety can beincreased by proper installation ...and thoughtful operation on yourpart. DO NOT INSTALL, OPER-ATE OR REPAIR THIS EQUIP-MENT WITHOUT READINGTHIS MANUAL AND THE SAFE-TY PRECAUTIONS CONTAINEDTHROUGHOUT. And, mostimportantly, think before you actand be careful.

For use with machine having Code Number: 11686

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

Copyright © Lincoln Global Inc.

®

iSAFETYi

FOR ENGINEpowered equipment.

1.a. Turn the engine off before troubleshooting and maintenancework unless the maintenance work requires it to be running.

____________________________________________________1.b. Operate engines in open, well-ventilated

areas or vent the engine exhaust fumesoutdoors.

____________________________________________________1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.Stop the engine and allow it to cool beforerefueling to prevent spilled fuel from vaporiz-ing on contact with hot engine parts andigniting. Do not spill fuel when filling tank. Iffuel is spilled, wipe it up and do not startengine until fumes have been eliminated.

____________________________________________________1.d. Keep all equipment safety guards, covers and devices in

position and in good repair.Keep hands, hair, clothing andtools away from V-belts, gears, fans and all other movingparts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safetyguards to perform required maintenance. Removeguards only when necessary and replace them when themaintenance requiring their removal is complete.Always use the greatest care when working near movingparts.

___________________________________________________1.f. Do not put your hands near the engine fan.

Do not attempt to override the governor oridler by pushing on the throttle control rodswhile the engine is running.

___________________________________________________1.g. To prevent accidentally starting gasoline engines while

turning the engine or welding generator during maintenancework, disconnect the spark plug wires, distributor cap ormagneto wire as appropriate.

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that youpurchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is availablefrom the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES AREPERFORMED ONLY BY QUALIFIED INDIVIDUALS.

WARNING

Mar ‘95

ELECTRIC ANDMAGNETIC FIELDSmay be dangerous

2.a. Electric current flowing through any conductor causeslocalized Electric and Magnetic Fields (EMF). Weldingcurrent creates EMF fields around welding cables andwelding machines

2.b. EMF fields may interfere with some pacemakers, andwelders having a pacemaker should consult their physicianbefore welding.

2.c. Exposure to EMF fields in welding may have other healtheffects which are now not known.

2.d. All welders should use the following procedures in order tominimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Securethem with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode andwork cables. If the electrode cable is on your rightside, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close aspossible to the area being welded.

2.d.5. Do not work next to welding power source.

1.h. To avoid scalding, do not remove theradiator pressure cap when the engine ishot.

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituentsare known to the State of California to cause can-cer, birth defects, and other reproductive harm.

The engine exhaust from this product containschemicals known to the State of California to causecancer, birth defects, or other reproductive harm.

The Above For Diesel Engines The Above For Gasoline Engines

iiSAFETYii

ARC RAYS can burn.4.a. Use a shield with the proper filter and cover

plates to protect your eyes from sparks andthe rays of the arc when welding or observingopen arc welding. Headshield and filter lensshould conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistantmaterial to protect your skin and that of your helpers fromthe arc rays.

4.c. Protect other nearby personnel with suitable, non-flammablescreening and/or warn them not to watch the arc nor exposethemselves to the arc rays or to hot spatter or metal.

ELECTRIC SHOCK cankill.3.a. The electrode and work (or ground) circuits

are electrically “hot” when the welder is on.Do not touch these “hot” parts with your bareskin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.Make certain the insulation is large enough to cover your fullarea of physical contact with work and ground.

In addition to the normal safety precautions, if weldingmust be performed under electrically hazardousconditions (in damp locations or while wearing wetclothing; on metal structures such as floors, gratings orscaffolds; when in cramped positions such as sitting,kneeling or lying, if there is a high risk of unavoidable oraccidental contact with the workpiece or ground) usethe following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.• DC Manual (Stick) Welder.• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,electrode reel, welding head, nozzle or semiautomaticwelding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electricalconnection with the metal being welded. The connectionshould be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical(earth) ground.

3.f. Maintain the electrode holder, work clamp, welding cable andwelding machine in good, safe operating condition. Replacedamaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts ofelectrode holders connected to two welders because voltagebetween the two can be the total of the open circuit voltageof both welders.

3.i. When working above floor level, use a safety belt to protectyourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

FUMES AND GASEScan be dangerous.5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing thesefumes and gases. When welding, keepyour head out of the fume. Use enoughventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. Whenwelding with electrodes which require specialventilation such as stainless or hard facing (seeinstructions on container or MSDS) or on lead orcadmium plated steel and other metals or coatingswhich produce highly toxic fumes, keep exposure aslow as possible and within applicable OSHA PEL andACGIH TLV limits using local exhaust or mechanicalventilation. In confined spaces or in some circum-stances, outdoors, a respirator may be required.Additional precautions are also required when weldingon galvanized steel.

5. b. The operation of welding fume control equipment is affectedby various factors including proper use and positioning ofthe equipment, maintenance of the equipment and the spe-cific welding procedure and application involved. Workerexposure level should be checked upon installation andperiodically thereafter to be certain it is within applicableOSHA PEL and ACGIH TLV limits.

5.c. Do not weld in locations near chlorinated hydrocarbon vaporscoming from degreasing, cleaning or spraying operations.The heat and rays of the arc can react with solvent vapors toform phosgene, a highly toxic gas, and other irritating prod-ucts.

5.d. Shielding gases used for arc welding can displace air andcause injury or death. Always use enough ventilation,especially in confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturer’s instructions for thisequipment and the consumables to be used, including thematerial safety data sheet (MSDS) and follow youremployer’s safety practices. MSDS forms are available fromyour welding distributor or from the manufacturer.

5.f. Also see item 1.b.

Jan ‘09

iiiSAFETYiii

FOR ELECTRICALLYpowered equipment.

8.a. Turn off input power using the disconnectswitch at the fuse box before working onthe equipment.

8.b. Install equipment in accordance with the U.S. NationalElectrical Code, all local codes and the manufacturer’srecommendations.

8.c. Ground the equipment in accordance with the U.S. NationalElectrical Code and the manufacturer’s recommendations.

CYLINDER may explodeif damaged.7.a. Use only compressed gas cylinders

containing the correct shielding gas for theprocess used and properly operatingregulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable forthe application and maintained in good condition.

7.b. Always keep cylinders in an upright position securelychained to an undercarriage or fixed support.

7.c. Cylinders should be located:• Away from areas where they may be struck or subjected tophysical damage.

• A safe distance from arc welding or cutting operations andany other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any otherelectrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outletwhen opening the cylinder valve.

7.f. Valve protection caps should always be in place and handtight except when the cylinder is in use or connected foruse.

7.g. Read and follow the instructions on compressed gascylinders, associated equipment, and CGA publication P-l,“Precautions for Safe Handling of Compressed Gases inCylinders,” available from the Compressed Gas Association1235 Jefferson Davis Highway, Arlington, VA 22202.

WELDING and CUTTINGSPARKS cancause fire or explosion.6.a. Remove fire hazards from the welding area.

If this is not possible, cover them to preventthe welding sparks from starting a fire.

Remember that welding sparks and hotmaterials from welding can easily go through small cracksand openings to adjacent areas. Avoid welding nearhydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,special precautions should be used to prevent hazardoussituations. Refer to “Safety in Welding and Cutting” (ANSIStandard Z49.1) and the operating information for theequipment being used.

6.c. When not welding, make certain no part of the electrodecircuit is touching the work or ground. Accidental contactcan cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until theproper steps have been taken to insure that such procedureswill not cause flammable or toxic vapors from substancesinside. They can cause an explosion even though they havebeen “cleaned”. For information, purchase “RecommendedSafe Practices for the Preparation for Welding and Cutting ofContainers and Piping That Have Held HazardousSubstances”, AWS F4.1 from the American Welding Society(see address above).

6.e. Vent hollow castings or containers before heating, cutting orwelding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oilfree protective garments such as leather gloves, heavy shirt,cuffless trousers, high shoes and a cap over your hair. Wearear plugs when welding out of position or in confined places.Always wear safety glasses with side shields when in awelding area.

6.g. Connect the work cable to the work as close to the weldingarea as practical. Work cables connected to the buildingframework or other locations away from the welding areaincrease the possibility of the welding current passingthrough lifting chains, crane cables or other alternate cir-cuits. This can create fire hazards or overheat lifting chainsor cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “ Standard for Fire PreventionDuring Welding, Cutting and Other Hot Work”, availablefrom NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma022690-9101.

6.j. Do not use a welding power source for pipe thawing.

Jan ‘09

Refer to http://www.lincolnelectric.com/safety for additional safety information.

ivSAFETYiv

Mar. ‘93

PRÉCAUTIONS DE SÛRETÉPour votre propre protection lire et observer toutes les instructionset les précautions de sûreté specifiques qui parraissent dans cemanuel aussi bien que les précautions de sûreté générales suiv-antes:

Sûreté Pour Soudage A L’Arc1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tensionquand la machine à souder est en marche. Eviter toujourstout contact entre les parties sous tension et la peau nueou les vétements mouillés. Porter des gants secs et sanstrous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand onsoude dans des endroits humides, ou sur un planchermetallique ou des grilles metalliques, principalement dansles positions assis ou couché pour lesquelles une grandepartie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câblede soudage et la machine à souder en bon et sûr étatdefonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour lerefroidir.

e. Ne jamais toucher simultanément les parties sous tensiondes porte-électrodes connectés à deux machines à souderparce que la tension entre les deux pinces peut être letotal de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source decourant pour soudage semi-automatique, ces precautionspour le porte-électrode s’applicuent aussi au pistolet desoudage.

2. Dans le cas de travail au dessus du niveau du sol, se protégercontre les chutes dans le cas ou on recoit un choc. Ne jamaisenrouler le câble-électrode autour de n’importe quelle partiedu corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,donc:

a. Utiliser un bon masque avec un verre filtrant appropriéainsi qu’un verre blanc afin de se protéger les yeux du ray-onnement de l’arc et des projections quand on soude ouquand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger lapeau de soudeur et des aides contre le rayonnement del‘arc.

c. Protéger l’autre personnel travaillant à proximité ausoudage à l’aide d’écrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de l’arc desoudage. Se protéger avec des vêtements de protection libresde l’huile, tels que les gants en cuir, chemise épaisse, pan-talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone desoudage. Utiliser des lunettes avec écrans lateraux dans leszones où l’on pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin deprévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé dela masse. Un court-circuit accidental peut provoquer unéchauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possiblede la zone de travail qu’il est pratique de le faire. Si on placela masse sur la charpente de la construction ou d’autresendroits éloignés de la zone de travail, on augmente le risquede voir passer le courant de soudage par les chaines de lev-age, câbles de grue, ou autres circuits. Cela peut provoquerdes risques d’incendie ou d’echauffement des chaines et descâbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.Ceci est particuliérement important pour le soudage de tôlesgalvanisées plombées, ou cadmiées ou tout autre métal quiproduit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenantd’opérations de dégraissage, nettoyage ou pistolage. Lachaleur ou les rayons de l’arc peuvent réagir avec les vapeursdu solvant pour produire du phosgéne (gas fortement toxique)ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,voir le code “Code for safety in welding and cutting” CSAStandard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POURLES MACHINES À SOUDER ÀTRANSFORMATEUR ET ÀREDRESSEUR

1. Relier à la terre le chassis du poste conformement au code del’électricité et aux recommendations du fabricant. Le dispositifde montage ou la piece à souder doit être branché à unebonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seronteffectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch-er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leurplace.

vSAFETYv

VANTAGE® 575 CUMMINS

Electromagnetic Compatibility (EMC)

ConformanceProducts displaying the CE mark are in conformity with European Community Council Directive of 3 May1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility(89/336/EEC). It was manufactured in conformity with a national standard that implements a harmonizedstandard: EN 60974-10 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment.It is for use with other Lincoln Electric equipment. It is designed for industrial and professional use.

IntroductionAll electrical equipment generates small amounts of electromagnetic emission. Electrical emission may betransmitted through power lines or radiated through space, similar to a radio transmitter. When emissionsare received by other equipment, electrical interference may result. Electrical emissions may affect manykinds of electrical equipment; other nearby welding equipment, radio and TV reception, numerical controlledmachines, telephone systems, computers, etc. Be aware that interference may result and extra precautionsmay be required when a welding power source is used in a domestic establishment.

Installation and UseThe user is responsible for installing and using the welding equipment according to the manufacturer’sinstructions. If electromagnetic disturbances are detected then it shall be the responsibility of the user of thewelding equipment to resolve the situation with the technical assistance of the manufacturer. In some casesthis remedial action may be as simple as earthing (grounding) the welding circuit, see Note. In other cases itcould involve construction of an electromagnetic screen enclosing the power source and the work completewith associated input filters. In all cases electromagnetic disturbances must be reduced to the point wherethey are no longer troublesome.

Note: The welding circuit may or may not be earthed for safety reasons according to national codes.Changing the earthing arrangements should only be authorized by a person who is compe-tent to access whether the changes will increase the risk of injury, e.g., by allowing parallelwelding current return paths which may damage the earth circuits of other equipment.

Assessment of AreaBefore installing welding equipment the user shall make an assessment of potential electromagnetic prob-lems in the surrounding area. The following shall be taken into account:

a) other supply cables, control cables, signaling and telephone cables; above, below and adjacent to thewelding equipment;

b) radio and television transmitters and receivers;

c) computer and other control equipment;

d) safety critical equipment, e.g., guarding of industrial equipment;

e) the health of the people around, e.g., the use of pacemakers and hearing aids;

f) equipment used for calibration or measurement

g) the immunity of other equipment in the environment. The user shall ensure that other equipment beingused in the environment is compatible. This may require additional protection measures;

h) the time of day that welding or other activities are to be carried out.

L10093 3-1-96H

viSAFETYvi


Electromagnetic Compatibility (EMC)

The size of the surrounding area to be considered will depend on the structure of the building and otheractivities that are taking place. The surrounding area may extend beyond the boundaries of the premises.

Methods of Reducing Emissions

Mains SupplyWelding equipment should be connected to the mains supply according to the manufacturer’s recommenda-tions. If interference occurs, it may be necessary to take additional precautions such as filtering of the mainssupply. Consideration should be given to shielding the supply cable of permanently installed welding equip-ment, in metallic conduit or equivalent. Shielding should be electrically continuous throughout its length. Theshielding should be connected to the welding power source so that good electrical contact is maintainedbetween the conduit and the welding power source enclosure.

Maintenance of the Welding EquipmentThe welding equipment should be routinely maintained according to the manufacturer’s recommendations.All access and service doors and covers should be closed and properly fastened when the welding equip-ment is in operation. The welding equipment should not be modified in any way except for those changesand adjustments covered in the manufacturers instructions. In particular, the spark gaps of arc striking andstabilizing devices should be adjusted and maintained according to the manufacturer’s recommendations.

Welding CablesThe welding cables should be kept as short as possible and should be positioned close together, running ator close to floor level.

Equipotential BondingBonding of all metallic components in the welding installation and adjacent to it should be considered.However, metallic components bonded to the work piece will increase the risk that the operator couldreceive a shock by touching these metallic components and the electrode at the same time. The operatorshould be insulated from all such bonded metallic components.

Earthing of the WorkpieceWhere the workpiece is not bonded to earth for electrical safety, not connected to earth because of its sizeand position, e.g., ships hull or building steelwork, a connection bonding the workpiece to earth may reduceemissions in some, but not all instances. Care should be taken to prevent the earthing of the workpieceincreasing the risk of injury to users, or damage to other electrical equipment. Where necessary, the connec-tion of the workpiece to earth should be made by a direct connection to the workpiece, but in some countrieswhere direct connection is not permitted, the bonding should be achieved by suitable capacitance, selectedaccording to national regulations.

Screening and ShieldingSelective screening and shielding of other cables and equipment in the surrounding area may alleviate prob-lems of interference. Screening of the entire welding installation may be considered for special applications.1

_________________________

1 Portions of the preceding text are contained in EN 60974-10: “Electromagnetic Compatibility (EMC) prod-uct standard for arc welding equipment.”

L10093 3-1-96H

viivii

Thank You for selecting a QUALITY product by Lincoln Electric. We want youto take pride in operating this Lincoln Electric Company product••• as much pride as we have in bringing this product to you!

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep ithandy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.The level of seriousness to be applied to each is explained below:

WARNINGThis statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.

CAUTION

Please Examine Carton and Equipment For Damage ImmediatelyWhen this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claimsfor material damaged in shipment must be made by the purchaser against the transportation company at thetime the shipment is received.

Please record your equipment identification information below for future reference. This information can befound on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information youhave recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packetaccompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then“Product Registration”. Please complete the form and submit your registration.

CUSTOMER ASSISTANCE POLICYThe business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask LincolnElectric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating orcorrecting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter anywarranty with respect to the sale of our products.

Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the controlof, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained inapplying these types of fabrication methods and service requirements.

Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.comfor any updated information.

viiiviii TABLE OF CONTENTSPage

Installation.......................................................................................................................Section ATechnical Specifications.......................................................................................................A-1

Safety Precautions ........................................................................................................A-2Location and Ventilation................................................................................................A-2Storing...........................................................................................................................A-2Stacking ........................................................................................................................A-2Angle of Operation ........................................................................................................A-2Lifting.............................................................................................................................A-3High Altitude Operation .................................................................................................A-3High Temperature Operation ........................................................................................A-3Towing...........................................................................................................................A-3Vehicle Mounting...........................................................................................................A-3

Pre-Operation Engine Service..............................................................................................A-4Oil ..................................................................................................................................A-4Fuel and Fuel Cap.........................................................................................................A-4Engine Coolant System.................................................................................................A-4Battery Connections......................................................................................................A-4Muffler Outlet Pipe ........................................................................................................A-5 Spark Arrestor ...............................................................................................................A-5

Air Cleaner Inlet Hood ..........................................................................................................A-5Welding Terminals................................................................................................................A-5

Welding Output Cables .................................................................................................A-5Machine Grounding.......................................................................................................A-5

Remote Control ....................................................................................................................A-6Auxiliary Power Receptacles and Standby Power Connections ..........................................A-6Connection of Lincoln Electric Wire Feeders................................................................A-7, A-8

________________________________________________________________________________

Operation.........................................................................................................................Section BSafety Precautions ..............................................................................................................B-1General Description..............................................................................................................B-1Recommended Application, Generator ................................................................................B-1Controls and Settings ...........................................................................................................B-2Engine Controls ............................................................................................................B-2, B-3Welder Controls ............................................................................................................B-3, B-4Auxiliary Power Controls...............................................................................................B-4, B-5Battery Jump Start Terminals...............................................................................................B-5What are VRD and ROCV Devices ..................................................................................... B-6

Welding Power Sources................................................................................................B-6Safety ............................................................................................................................B-6VRD Operation Indicators .............................................................................................B-6Operation ......................................................................................................................B-6

Starting Technique ...............................................................................................................B-7Break-In Period ....................................................................................................................B-7Typical Fuel Consumption....................................................................................................B-7Welding Operation................................................................................................................B-8

Duty Cycle.....................................................................................................................B-8Stick Welding Mode ......................................................................................................B-8CC-Stick Mode ..............................................................................................................B-8Touch Start TIG Mode...................................................................................................B-8VANTAGE® 575 Settings when using K930-2 TIG Module..........................................B-8

Wire Welding-CV..................................................................................................................B-9Arc Gouging .........................................................................................................................B-9Typical Current Ranges for Tungsten Electrodes ................................................................B-9Paralleling...........................................................................................................................B-10Auxiliary Power Operation..................................................................................................B-10Simultaneous Welding and Auxiliary Power Loads ............................................................B-10Simultaneous Welding and Power Loads, Extension Cord Length Recommendations .....B-10

ix ixTABLE OF CONTENTSAccessories........................................................................................................Section c

Optional Field Installed Accessories......................................................................C-1________________________________________________________________________

Maintenance.......................................................................................................Section DSafety Precautions ................................................................................................D-1Routine and Periodic Maintenance .......................................................................D-1Engine Maintenance..............................................................................................D-1

Air Filter...................................................................................................D-1, D-2Fuel Filters ......................................................................................................D-3Cooling System...............................................................................................D-3Battery Handling .............................................................................................D-3

Charging the Battery .............................................................................................D-4Nameplate / Warning Decal Maintenance.............................................................D-4Welder / Generator Maintenance ..........................................................................D-4Engine Maintenance Components ........................................................................D-4

________________________________________________________________________Troubleshooting ..............................................................................................Section E

________________________________________________________________________ Connection Diagrams, Wiring Diagrams and Dimension Print...................Section F

________________________________________________________________________Parts List ...................................................................................................P-639 Series

________________________________________________________________________


A-1INSTALLATION A-1

TECHNICAL SPECIFICATIONS - VANTAGE® 575 CUMMINS (K2170-2)

Make/Model Description Speed (RPM) Displacement Starting Capacitiescu. in. (ltrs.) System

4 cylinder High Idle 1590 199(3.3) 12VDC Battery & Fuel: 25 gal.Cummins 48 HP (36kw) starter (94.6 L)B3.3 1500 RPM Full Load 1500 Bore x Stroke inch (mm) Oil: 2 gal. (7.5L)

Diesel EngineLow Idle 1300 3.74 X 4.53 Radiator Coolant:

(95 x 115mm) 2.6gal. (9.8L)

INPUT - DIESEL ENGINE

RATED OUTPUT @ 104°F(40°C) - WELDER

Duty Cycle Welding Output Volts at Rated Amps

100% 450 Amps (DC multi-purpose) 38 Volts

60% 500 Amps (DC multi-purpose) 40 volts

PHYSICAL DIMENSIONSHeight (2) Width Depth Weight

42.0 in 32.7 in. 63.1 in. 1625 lbs.(1066.8 mm) (830.1mm) (1603mm) (737kg)

(Approx)1. Output rating in watts is equivalent to volt-amperes at unity power factor.

Output voltage is within +/- 10% at all loads up to rated capacity. When welding, available auxiliary power will be reduced.2. Top of Enclosure, add 7.0” (177.8mm) for exhaust pipe.

OUTPUT @ 104°F(40°C) - WELDER AND GENERATOR

Welding Range

30 - 575 Amps CC/CV20 - 250 Amps TIG

Open Circuit Voltage

60 Max OCV @ 1590 RPM

Auxiliary Power (1) (50 Hz)

Outlets x Phase Voltage Power Amps

1 x 3ph 415 Volts 20 Kva 32 Amps

2 x 1ph 240 Volts 7.2 Kva 15 Amps

A-2INSTALLATION


A-2

SAFETY PRECAUTIONS

Only qualified personnel should install, use, or service this equipment.

Do not attempt to use this equipment until youhave thoroughly read the engine manufacturer’smanual supplied with your welder. It includesimportant safety precautions, detailed enginestarting, operating and maintenance instructions,and parts lists.------------------------------------------------------------------------

ELECTRIC SHOCK can kill.• Do not touch electrically live parts or

electrode with skin or wet clothing.• Insulate yourself from work and

ground• Always wear dry insulating gloves.

------------------------------------------------------------------------ENGINE EXHAUST can kill.• Use in open, well ventilated areas or

vent exhaust outside.

------------------------------------------------------------------------MOVING PARTS can injure.• Do not operate with doors open or

guards off.• Stop engine before servicing.• Keep away from moving parts.

------------------------------------------------------------------------See additional warning information atfront of this operator’s manual.

WARNING

STORING1. Store the machine in a cool, dry place when it is

not in use. Protect it from dust and dirt. Keep itwhere it can’t be accidentally damaged from con-struction activities, moving vehicles, and otherhazards.

2. Drain the engine oil and refill with fresh 10W30oil. Run the engine for about five minutes to cir-culate oil to all the parts. See the MAINTE-NANCE section of this manual for details onchanging oil.

3. Remove the battery, recharge it, and adjust theelectrolyte level. Store the battery in a dry, darkplace.

STACKINGVANTAGE® 575 CUMMINS machines cannot bestacked.

ANGLE OF OPERATIONTo achieve optimum engine performance the VAN-TAGE® 575 CUMMINS should be run in a level posi-tion. The maximum angle of operation for the VAN-TAGE® 575 CUMMINS engine is 20 degrees contin-ues in all directions and 30 degrees intermittent (lessthan 10 minutes). When operating the welder at anangle, provisions must be made for checking andmaintaining the oil level at the normal (FULL) oilcapacity. Also the effective fuel capacity will be slightlyless than the specified 25 gal.(94.6 ltrs.).

LOCATION AND VENTILATION

The welder should be located to provide an unrestrict-ed flow of clean, cool air to the cooling air inlets and toavoid restricting the cooling air outlets. Also, locatethe welder so that the engine exhaust fumes are prop-erly vented to an outside area.

DO NOT MOUNT OVER COMBUSTIBLE SURFACESWhere there is a combustible surface directlyunder stationary or fixed electrical equipment, thatsurface should be covered with a steel plate atleast .06”(1.6mm) thick, which should extend notless than 5.90”(150mm) beyond the equipment onall sides.

------------------------------------------------------------------------

CAUTION

A-3INSTALLATION


A-3

LIFTINGThe VANTAGE® 575 CUMMINS lift bale should beused to lift the machine. The VANTAGE® 575 CUM-MINS is shipped with the lift bale retracted. Beforeattempting to lift the VANTAGE® 575 CUMMINS thelift bale must be secured in a raised position. Securethe lift bale as follows:

a. Open the engine compartment door.

b. Locate the 2 access holes on the upper middleregion of compartment wall just below the liftbale.

c. Use the lifting strap to raise the lift bale to thefull upright position. This will align the mount-ing holes on the lift bale with the access holes.

d. Secure the lift bale with 2 thread formingscrews. The screws are provided in theshipped loose parts bag.

HIGH ALTITUDE OPERATIONAt higher altitudes, output derating may be necessary.For maximum rating, derate the welder output 4% forevery 300 meters (984 ft.) above 1500 meters (4920ft.). For output of 500A and below, derate the welderoutput 4% for every 300 meters (984 ft.) above 2100meters (6888 ft.).

Contact a Cummins Service Representative for anyengine adjustments that may be required.

HIGH TEMPERATURE OPERATIONAt temperatures above 40°C (104°F), output voltagederating may be necessary. For maximum output cur-rent ratings, derate welder voltage rating 2 volts forevery 10°C (21°F) above 40°C (104°F).

• Lift only with equipment of ade-quate lifting capacity.

• Be sure machine is stable when lift-ing.

• Do not lift this machine using liftbail if it is equipped with a heavyaccessory such as trailer or gascylinder.

FALLING • Do not lift machine if lift bail is

EQUIPMENT can damaged.

cause injury. • Do not operate machine while

suspended from lift bail.------------------------------------------------------------------------

TOWINGThe recommended trailer for use with this equipmentfor road, in-plant and yard towing by a vehicle (1) isLincoln’s K2636-1. If the user adapts a non-Lincolntrailer, he must assume responsibility that the methodof attachment and usage does not result in a safetyhazard nor damage the welding equipment. Some ofthe factors to be considered are as follows:

1. Design capacity of trailer vs. weight of Lincolnequipment and likely additional attachments.

2. Proper support of, and attachment to, the base ofthe welding equipment so that there will be noundue stress to the trailer’s framework.

3. Proper placement of the equipment on the trailerto insure stability side to side and front to backwhen being moved and when standing by itself.

4. Typical conditions of use, such as travel speed,roughness of surface on which the trailer will beoperated, and environmental conditions.

5. Proper preventative maintenance of trailer.

6. Conformance with federal, state and local laws (1) .(1) Consult applicable federal, state and local laws

regarding specific requirements for use on publichighways.

VEHICLE MOUNTING

Improperly mounted concentrated loads maycause unstable vehicle handling and tires or othercomponents to fail.• Only transport this Equipment on serviceable

vehicles which are rated and designed for suchloads.

• Distribute, balance and secure loads so vehicleis stable under conditions of use.

• Do not exceed maximum rated loads for compo-nents such as suspension, axles and tires.

• Mount equipment base to metal bed or frame ofvehicle.

• Follow vehicle manufacture’s instructions.------------------------------------------------------------------------

WARNING

WARNING

ENGINE COOLANT

HOT COOLANT can burn skin.

•Do not remove cap if radiator is hot.

------------------------------------------------------------------------

The welder is shipped with the engine and radiatorfilled with a 50% mixture of ethylene glycol and water.See the MAINTENANCE section and the engineOperator’s Manual for more information on coolant.

BATTERY CONNECTION

GASES FROM BATTERY can explode.

• Keep sparks, flame and cigarettesaway from battery.

To prevent EXPLOSION when:

• INSTALLING A NEW BATTERY — disconnectnegative cable from old battery first and connectto new battery last.

• CONNECTING A BATTERY CHARGER — removebattery from welder by disconnecting negativecable first, then positive cable and battery clamp.When reinstalling, connect negative cable last.Keep well ventilated.

• USING A BOOSTER — connect positive lead tobattery first then connect negative lead to nega-tive battery lead at engine foot.

BATTERY ACID can burn eyes and skin.

• Wear gloves and eye protection andbe careful when working near battery.

• Follow instructions printed on battery.

------------------------------------------------------------------------

IMPORTANT: To prevent ELECTRICAL DAMAGEWHEN:

a) Installing new batteries.

b) Using a booster.

Use correct polarity — Negative Ground.

PRE-OPERATION ENGINE AND COM-PRESSOR SERVICEREAD the engine and compressor operating andmaintenance instructions supplied with this machine.

• Keep hands away from the enginemuffler or HOT engine parts.

• Stop engine and allow to cool beforefuelling.

• Do not smoke when fuelling.

• Fill fuel tank at a moderate rate and do not over-fill.

• Wipe up spilled fuel and allow fumes to clearbefore starting engine.

• Keep sparks and flame away from tank.

------------------------------------------------------------------------

OILThe VANTAGE® 575 CUMMINS is shipped with theengine crankcase filled with high quality SAE 10W-30oil (API class CD or better). Check the engine andcompressor oil levels before starting the engine. If it isnot up to the full mark on the dip stick, add oil asrequired. Check the oil level every four hours of run-ning time during the first 35 running hours. Refer tothe engine Operator’s Manuals for specific oil recom-mendations and break-in information. The oil changeinterval is dependent on the quality of the oil and theoperating environment. Refer to the engine Operator’sManuals for the proper service and maintenance inter-vals.

FUEL USE DIESEL FUEL ONLY

• Fill the fuel tank with clean, fresh diesel fuel. Thecapacity of the fuel tank is approximately 25 gallons(95 liters). See engine Operator’s Manual for specif-ic fuel recommendations. Running out of fuel mayrequire bleeding the fuel injection pump.

NOTE: Before starting the engine, open the fuel shut-off valve (pointer to be in line with hose).

FUEL CAPRemove the plastic cap covering from the Fuel TankFiller neck and install the Fuel Cap.

A-4INSTALLATION


A-4

WARNING

WARNING

WARNING

A-5INSTALLATION


A-5

The VANTAGE® 575 CUMMINS is shipped with the nega-tive battery cable disconnected. Before you operate themachine, make sure the Engine Switch is in the OFF posi-tion and attach the disconnected cable securely to the nega-tive (-) battery terminal.

Remove the insulating cap from the negative battery termi-nal. Replace and tighten negative battery cable terminal.NOTE: This machine is furnished with a wet charged bat-tery; if unused for several months, the battery may require abooster charge. Be sure to use the correct polarity whencharging the battery.

MUFFLER OUTLET PIPERemove the plastic plug covering the muffler outlet tube.Using the clamp provided secure the outlet pipe to the outlettube with the pipe positioned such that it will direct theexhaust in the desired position.

SPARK ARRESTORSome federal, state or local laws may require that petrol ordiesel engines be equipped with exhaust spark arrestorswhen they are operated in certain locations where unarrest-ed sparks may present a fire hazard. The standard mufflerincluded with this welder has an internal spark arrestor.When required by local regulations, a suitable sparkarrestor, must be installed and properly maintained.

An incorrect arrestor may lead to damage to the engineor adversely affect performance.------------------------------------------------------------------------------AIR CLEANER INLET HOODRemove the plastic plug covering the air cleaner inlet. Installthe air cleaner inlet hood to the air cleaner.

WELDING TERMINALSThe VANTAGE® 575 CUMMINS is equipped with a toggleswitch for selecting "hot" welding terminals when in the"WELD TERMINALS ON" position or "cold" welding termi-nals when in the "REMOTELY CONTROLLED" position.

There is no VRD protection in the CV mode.

With the toggle switch in the “WELD TERMINAL ON”position the voltage at the output terminal maybe up to60V. Only a LN-25 wire feeder with internal contactorshould be used in this set up.

-------------------------------------------------------------------------------WELDING OUTPUT CABLESWith the engine off, route the electrode and work cables thruthe strain relief bracket provided on the front of the base andconnect to the terminals provided. These connectionsshould be checked periodically and tightened if necessary.

Listed in Table A.1 are copper cable sizes recom-mended for the rated current and duty cycle. Lengthsstipulated are the distance from the welder to workand back to the welder again. Cable sizes areincreased for greater lengths primarily for the purposeof minimizing cable voltage drop.

Table A.1 Combined Length of Electrode andWork Cables.

MACHINE GROUNDINGBecause this portable engine driven welder creates itsown power, it is not necessary to connect its frame toan earth ground, unless the machine is connected topremises wiring (home, shop, etc.).

To prevent dangerous electric shock, other equipmentto which this engine driven welder supplies powermust:

• Be grounded to the frame of the welder using agrounded type plug or be double insulated.

• Do not ground the machine to a pipe that carriesexplosive or combustible material.

------------------------------------------------------------------------When this welder is mounted on a truck or trailer, itsframe must be securely connected to the metal frameof the vehicle. When this engine driven welder is con-nected to premises wiring such as that in a home orshop, its frame must be connected to the system earthground. See further connection instructions in the sec-tion entitled “Standby Power Connections” as well as the article on grounding in the latest NationalElectrical Code and the local codes.

In general, if the machine is to be grounded, it shouldbe connected with a #8 or larger copper wire to a solidearth ground such as a metal ground stake going intothe ground for at least 10 Feet or to the metal frame-work of a building which has been effectively ground-ed.

The National Electric Code lists a number of alternatemeans of grounding electrical equipment. A machinegrounding stud marked with the symbol is providedon the front of the welder.

CAUTION

TOTAL COMBINED LENGTH OFELECTRODE AND WORK CABLES

Cable Length

0-150 Ft. (0-46 meters)150-200 Ft. (46-61 meters)200-250 Ft. (61-76 meters)

Cable Size for 500 Amps

100% Duty Cycle3/0 AWG (95mm2)

3/0 AWG (95mm2)

4/0 AWG(120mm2)

WARNING

WARNING

A-6INSTALLATION


A-6

REMOTE CONTROLThe VANTAGE® 575 CUMMINS is equipped with a 6-pin and a 14-pin connector. The 6-pin connector is forconnecting the K857 or K857-1 Remote Control or forTIG welding, the K870 foot Amptrol or the K963-3hand Amptrol. When in the CC-STICK or CV-WIREmodes and when a remote control is connected to the6-pin Connector, the auto-sensing circuit automaticallyswitches the OUTPUT control from control at thewelder to remote control.

When in TOUCH START TIG mode and when aAmptrol is connected to the 6-Pin Connector, theOUTPUT dial is used to set the maximum currentrange of the CURRENT CONTROL of the Amptrol.

In the CV-WIRE mode, if the feeder being used has avoltage control when the wire feeder control cable isconnected to the 14-Pin Connector, the auto-sensingcircuit automatically makes OUTPUT CONTROL inac-tive and the wire feeder voltage control active.Otherwise, the OUTPUT CONTROL is used to presetthe voltage.

The 14-pin connector is used to directly connect awire feeder control cable. In the CV-WIRE mode,when the control cable is connected to the 14-pin con-nector, the auto-sensing circuit automatically makesthe Output Control inactive and the wire feeder volt-age control active.

NOTE: When a wire feeder with a built in weldingvoltage control is connected to the 14-pin connec-tor, do not connect anything to the 6-pin connec-tor.

------------------------------------------------------------------------

AUXILIARY POWER RECEPTACLES

The auxiliary power capacity of the VANTAGE® 575CUMMINS is 20kVA of 50Hz three phase power pro-tected by an RCD (Residual Current Device) and a 3phase 32 amp circuit breaker. The auxiliary powercapacity in watts equivalent to volt-amperes at unitypower factor.

This model has:

1 x 3 phase and neutral Residual Current Device(RCD) protection (30mA)

1 x 3 phase 32 amp Circuit Breaker

1 x 3 phase 415 volt 32 amp

2 x 1 phase 15 amp Circuit Breakers

2 x 1 phase 240 volt 15 amp per outlet

Note: The single-phase outlets are from differentphases and cannot be paralleled.

The auxiliary power receptacles should only be usedwith three or four wire earthed type plugs or approveddouble insulated tools. The current rating of any plugused with the system must be at least equal to thecurrent capacity of the associated receptacle.

STANDBY POWER CONNECTIONSThe VANTAGE® 575 CUMMINS is suitable for tempo-rary, standby or emergency power using the enginemanufacturer’s recommended maintenance schedule.

The VANTAGE® 575 CUMMINS can be permanentlyinstalled as a standby power unit for 415/240 volt (50Hz). Connections must be made by a licensed electri-cian who can determine how the 415/240 VAC powercan be adapted to the particular installation and com-ply with all applicable electrical codes. The followinginformation can be used as a guide by the electricianfor most applications.

1. Install an isolation switch between the power com-pany meter and the premises disconnect.(TheVANTAGE® 575 CUMMINS and the power compa-ny supplies must not be connected together).

Switch rating must be the same or greater than thecustomer’s premises disconnect and service overcurrent protection.

2. Take necessary steps to assure load is limited tothe capacity of the VANTAGE® 575 CUMMINS byinstalling a 32 amp, 415 VAC three pole circuitbreaker. Loading above the rated output will reduceoutput voltage below the allowable -10% of ratedvoltage which may damage appliances or othermotor-driven equipment and may result in overheat-ing of the VANTAGE® 575 CUMMINS engine.

3. Install a 32 amp 3 phase plug to the triple-pole cir-cuit breaker using 6.02mm (minimum) x 4 conduc-tor cable of the desired length.(1 x 32 amp / 415 V& 2 x 15 amp / 240 V, plugs are available in theoptional KA1373-2 plug kit).

4. Plug this cable into the 3 phase receptacle on theVANTAGE® 575 CUMMINS case front.

WARNING

A-7INSTALLATION


A-7

CONNECTION OF LINCOLN ELEC-TRIC WIRE FEEDERS

Shut off welder before making any electrical con-nections.

------------------------------------------------------------------------

Connection of LN-7, LN-8 OR LN-742 to the VAN-TAGE® 575 CUMMINS

1. Shut the welder off.

2. Connect the LN-7, LN-8 OR LN-742 per instruc-tions on the appropriate connection diagram inSection F.

3. Set the "WIRE FEEDER VOLTMETER" switch toeither "+" or "-" as required by the electrode beingused.

4. Set the "MODE" switch to the "CV WIRE " posi-tion.

5. Set the "ARC CONTROL" knob to "0" initially andadjust to suit.

6. Set the "WELD TERMINALS" switch to the"REMOTELY CONTROLLED" position.

7. Set the "IDLE" switch to the "HIGH" position.

Connection of LN-15 to the VANTAGE® 575 CUM-MINS

These connections instructions apply to both the LN-15 Across-The-Arc and Control Cable models. TheLN-15 has an internal contactor and the electrode isnot energized until the gun trigger is closed. When thegun trigger is closed the wire will begin to feed and thewelding process is started.


2. For electrode Positive, connect the electrodecable to the "+" terminal of the welder and workcable to the "-" terminal of the welder. For elec-trode Negative, connect the electrode cable to the"-" terminal of the welder and work cable to the "+"terminal of the welder.

3. Across The-Arc Model:

• Attach the single lead from the front of the LN-15to work using the spring clip at the end of thelead. This is a control lead to supply current tothe wire feeder motor; it does not carry weldingcurrent.

• Set the "WELD TERMINALS" switch to "WELDTERMINALS ON".

• When the gun trigger is closed, the current sens-ing circuit will cause the VANTAGE® 575 CUM-MINS engine to go to the high idle speed, thewire will begin to feed and the welding processstarted. When welding is stopped, the engine willrevert to low idle speed after approximately 12seconds unless welding is resumed.

4. Control Cable Model:

• Connect Control Cable between Engine Welderand Feeder.

• Set the "WELD TERMINALS" switch to"REMOTELY CONTROLLED"

• Set the MODE switch to the "CV-WIRE " position.

• Set the "WIRE FEEDER VOLTMETER" switch toeither "+" or "-" as required by the electrode polar-ity being used.

• Set the "ARC CONTROL" knob to "0" initially andadjust to suit.

• Set the "IDLE" switch to the "AUTO" position.

• When the gun trigger is closed, the current sens-ing circuit will cause the VANTAGE® 575 CUM-MINS engine to go to the high idle speed, thewire will begin to feed and the welding processstarted. When welding is stopped, the engine willrevert to low idle speed after approximately 12seconds unless welding is resumed.

WARNING

A-8INSTALLATION


A-8

CONNECTION OF AN NA-3 AUTOMATICWELDING SYSTEM TO THE VANTAGE®575 CUMMINSFor connection diagrams and instructions for connect-ing an NA-3 Welding System to the VANTAGE® 575CUMMINS, refer to the NA-3 Welding System instruc-tion manual. The connection diagram for the LN-8 canbe used for connecting the NA-3.

• Set the Wire Feeder Voltage Switch to 115V.

CONNECTION OF MAGNUM SC SPOOLGUN TO THE VANTAGE® 575 CUMMINS(SEE SECTION F)

Spool Gun (K487-25) and Cobramatic to VAN-TAGE® 575 CUMMINS.

• Shut the welder off.

• Connect per instructions on the appropriate connec-tion diagram in Section F.

CONNECTION OF THE LN-25 TO THE VAN-TAGE® 575 CUMMINS.

Shut off welder before making any electrical con-nections.--------------------------------------------------------------------------The LN-25 with or without an internal contactor may beused with the VANTAGE® 575 CUMMINS. See theappropriate connection diagram in Section F.NOTE: The LN-25 (K431) Remote Control Module and(K432) Remote Cable are not recommended for usewith the VANTAGE® 575 CUMMINS.


2. For electrode Positive, connect the electrode cablefrom the LN-25 to the "+" terminal of the welder andwork cable to the "-" terminal of the welder. Forelectrode Negative, connect the electrode cablefrom the LN-25 to the "-" terminal of the welder andwork cable to the "+" terminal of the welder.

3. Attach the single lead from the front of the LN-25 towork using the spring clip at the end of the lead.This is a control lead to supply current to the wirefeeder motor; it does not carry welding current.

4. Set the MODE switch to the "CV-WIRE " position.

5. Set the "WELD TERMINALS" switch to "WELDTERMINALS ON"

6. Set the "ARC CONTROL" knob to "0" initially andadjust to suit.

7. Set the "IDLE" switch to the "AUTO" position. Whennot welding, the VANTAGE® 575 CUMMINSengine will be at the low idle speed. If you are usingan LN-25 with an internal contactor, the electrode isnot energized until the gun trigger is closed.

8. When the gun trigger is closed, the current sensingcircuit will cause the VANTAGE® 575 CUMMINSengine to go to the high idle speed, the wire willbegin to feed and the welding process started.When welding is stopped, the engine will revert tolow idle speed after approximately 12 secondsunless welding is resumed.

If you are using an LN-25 without an internal con-tactor, the electrode will be energized when theVANTAGE® 575 CUMMINS is started.--------------------------------------------------------------------------

WARNING

CAUTION

B-1OPERATION


B-1

SAFETY PRECAUTIONS

Read and understand this entire section beforeoperating your VANTAGE® 575 CUMMINS.

Do not attempt to use this equipment until you havethoroughly read the engine manufacturer’s manualsupplied with your welder. It includes importantsafety precautions, detailed engine starting, operat-ing and maintenance instructions, and parts lists.------------------------------------------------------------------------

ELECTRIC SHOCK can kill.• Do not touch electrically live parts or

electrode with skin or wet clothing.• Insulate yourself from work and

ground• Always wear dry insulating gloves.

--------------------------------------------------------------------------ENGINE EXHAUST can kill.• Use in open, well ventilated areas or

vent exhaust outside• Do not stack anything near the engine.

------------------------------------------------------------------------MOVING PARTS can injure.• Do not operate with doors open or

guards off.• Stop engine before servicing.• Keep away from moving parts

------------------------------------------------------------------------• Only qualified personnel should operate this

equipment.

• Always operate the welder with the sliding doorclosed and the side panels in place as these pro-vide maximum protection from moving parts andinsure proper cooling air flow.

GENERAL DESCRIPTION

The VANTAGE® 575 CUMMINS is a diesel engine-dri-ven welding power source. The machine uses a brushtype alternating current generator for DC multi-purposewelding. The DC welding control system uses state ofthe art Chopper Technology for superior weldingperformance.

WARNING

CT R

RECOMMENDED APPLICATIONSThe VANTAGE® 575 CUMMINS provides excellentconstant current DC welding output for stick (SMAW)and TIG welding. The VANTAGE® 575 CUMMINSalso provides excellent constant voltage DC weldingoutput for MIG (GMAW), Innershield (FCAW),Outershield (FCAW-G) and Metal Core welding. Inaddition the VANTAGE® 575 CUMMINS can be usedfor Arc Gouging with carbons up to 3/8”(10mm) indiameter.

The VANTAGE® 575 CUMMINS is not recommend-ed for pipe thawing.

GENERATOR

The VANTAGE® 575 CUMMINS provides smoothoutput for auxiliary power and emergency standbypower.

B-2OPERATIONB-2

ENGINE CONTROLS (Items 1 through 9)

1. RUN STOP SWITCHToggling the switch to the RUN position energizesthe fuel solenoid for approximately 30 seconds.The engine must be started within that time or thefuel solenoid will deenergize, and the switch mustbe toggled to reset the timer.

2. START PUSHBUTTONEnergizes the starter motor to crank the engine.With the engine "Run / Stop" switch in the "Run"position, push and hold the Start button to crankthe engine; release as the engine starts. Do notpress while engine is running since this cancause damage to the ring gear and/or startermotor.

3. ENGINE STOP SWITCH

Shut’s down engine.

4. HOUR METERThe hour meter displays the total time that theengine has been running. This meter is a usefulindicator for scheduling preventive maintenance.

5. FUEL LEVEL GAUGEDisplays the level of diesel fuel in the fuel tank.

The operator must watch the fuel level close-ly to prevent running out of fuel and possiblyhaving to bleed the system.

6. ENGINE TEMPERATURE GAUGEThe gauge displays the engine coolant tempera-ture.

FIGURE B.1


1

2

173

4

18

20

19

16

13

12

15

14

65 7

8

22

23

21

21

109

26

25

27

28

11

29

24

C32 6kA

415V~ 50/60Hz

CONTROLS AND SETTINGSAll welder and engine controls are located on the case frontpanel. Refer to Figure B.1 and the explanations that follow.

B-3OPERATIONB-3

7. OIL PRESSURE GAUGEThe gauge displays the engine oil pressure whenthe engine is running.

8. ENGINE PROTECTIONThe yellow engine protection light remains offwith proper oil pressure and under normal oper-ating temperatures. If the light turns on, theengine protection system will stop the engine.Check for proper oil level and add oil if neces-sary. Check for loose or disconnected leads atthe oil pressure sender located on the engine.The light will remain on when the engine hasbeen shut down due to low oil pressure or over-temperature condition.

9. BATTERY CHARGING LIGHTThe yellow engine alternator light is off when bat-tery charging system is functioning normally. Iflight turns on the alternator or the voltage regula-tor may not be operating correctly. The light willremain on when the engine is stopped and therun/stop switch is in the run position.

10. IDLER SWITCHHas two positions as follows:

A) In the “High” position , the engine runs atthe high idle speed controlled by the governor.

B) In the “Auto” / position, theidler operates as follows:

a. When switched from “High” to “Auto” or afterstarting the engine, the engine will operate atfull speed for approximately 12 seconds andthen go to low idle speed.

b. When the electrode touches the work or poweris drawn for lights or tools (approximately 100Watts minimum) the engine accelerates andoperates at full speed.

c. When welding ceases and the AC power loadis turned off, a fixed time delay of approximate-ly 12 seconds starts.

d. If the welding or AC power load is not restart-ed before the end of the time delay, the idlerreduces the engine speed to low idle speed.

e. The engine will automatically return to highidle speed when the welding load or A.C.power load is reapplied.

Idler Operational exceptions

When the WELDING TERMINALS switch is inthe “Remotely Controlled” position the idler willoperate as follows:

a. When the triggering device (Amptrol, Arc StartSwitch, etc.) is pressed the engine will acceler-ate and operate at full speed provided a weld-ing load is applied within approximately 12seconds.

• If the triggering device remains pressed but nowelding load is applied within approximately 12seconds the engine may return to low idlespeed.

• If the triggering device is released or weldingceases the engine will return to low idle speedafter approximately 12 seconds.

WELDING CONTROLS (Items 11through 20)

11. OUTPUT CONTROL: The OUTPUT dial is used to preset the outputvoltage or current as displayed on the digitalmeters for the four welding modes. When in theCC-STICK or CV-WIRE modes and when aremote control is connected to the 6-Pin or 14-Pin Connector, the auto-sensing circuit automati-cally switches the OUTPUT CONTROL from con-trol at the welder to the remote control. In theCV-WIRE mode, when the wire feeder controlcable is connected to the 14-Pin Connector, theauto-sensing circuit automatically makes OUT-PUT CONTROL inactive and the wire feeder volt-age control active.

When in the TOUCH START TIG mode andwhen a Amptrol is connected to the 6-PinConnector, the OUTPUT dial is used to set themaximum current range of the CURRENT CON-TROL of the Amptrol.

12. DIGITAL OUTPUT METERS: The digital meters allow the output voltage (CV-WIRE mode) or current (CC-STICK and TIGmodes) to be set prior to welding using the OUT-PUT control knob. During welding, the metersdisplay the actual output voltage (VOLTS) andcurrent (AMPS). A memory feature holds the dis-play of both meters on the seven seconds afterwelding is stopped. This allows the operator toread the actual current and voltage just prior towhen welding was ceased. While the display isbeing held the left-most decimal point in eachdisplay will be flashing. The accuracy of themeters is ± 3%.


B-4OPERATIONB-4

13. WELD MODE SELECTOR SWITCH:(Provides 3 selectable welding modes)

CV-WIRE

CC-STICK

TOUCH START TIG

14. ARC CONTROL:The ARC CONTROL WIRE/STICK knob is activein the WIRE and STICK modes, and has differentfunctions in these modes. This control is notactive in the TIG mode.

CC-STICK mode: In this mode, the ARC CON-TROL knob sets the short circuit current (arc-force) during stick welding. Increasing the num-ber from -10(Soft) to +10(Crisp) increases theshort circuit current and prevents sticking of theelectrode to the plate while welding. This canalso increase spatter. It is recommended that theARC CONTROL be set to the minimum numberwithout electrode sticking. Start with a setting at0.

CV-WIRE mode: In this mode, turning the ARCCONTROL knob from -10(soft) to +10(crisp)changes the arc from soft and washed-in to crispand narrow. It acts as an inductance/pinch con-trol. The proper setting depends on the proce-dure and operator preference. Start with a settingof 0.

15. WELDING TERMINALS SWITCH:In the WELD TERMINALS ON position, the out-put is electrically hot all the t ime. In theREMOTELY CONTROLLED position, the outputis controlled by a wire feeder or amptrol device,and is electrically off until a remote switch isdepressed.

• There is no VRD protection in the CV Mode.

• When the Toggle switch is in the “WELDTERMINAL ON” position the voltage at theoutput terminal maybe up to 60V.

-----------------------------------------------------------------------

16. WIRE FEEDER VOLTMETER SWITCH:

Matches the polarity of the wire feeder volt-meter to the polarity of the electrode.

17. 6 - PIN CONNECTOR:

For attaching optional remote control equipment.When in the CC-STICK and CV-WIRE modesand when a remote control is connected to theConnector, the auto-sensing circuit automaticallyswitches the OUTPUT control from control at thewelder to remote control.

18. 14-PIN CONNECTOR:

For attaching wire feeder control cable. Includescontactor closure circuit, auto-sensing remotecontrol circuit, and 42VAC or 115VAC power.The remote control circuit operates the same asthe 6-Pin Connector.

19. 42V / 115V WIRE FEEDER VOLTAGESWITCH:

Toggles output of 14-pin connector to voltagerequirement of Wire Feeder. (Located above 14-pin connector.)

20. WELD OUTPUT TERMINALS + AND -These 1/2” - 13 studs with flange nuts providewelding connection points for the electrode andwork cables. For positive polarity welding theelectrode cable connects to the “+” terminal andthe work cable connects to this “-” terminal. Fornegative polarity welding the work cable con-nects to the “+” terminal and the electrode cableconnects to this “-” terminal.

AUXILIARY POWER CONTROLS(Items 21-24)

21. CIRCUIT BREAKERSThese circuit breakers provide separate overloadcurrent protection for each 240V receptacles,415V 3 phase receptacle, the 42VAC and115VAC in the 14-Pin connector and battery cir-cuit overload protection.

22. 240 VAC RECEPTACLESThese two 240VAC receptacles provide up to 15amp total rating each and are IP66 rated. Referto the AUXILIARY POWER RECEPTACLESsection in the installation chapter for further infor-mation about these receptacles. Also refer to theAUXILIARY POWER OPERATION section laterin this chapter.


WARNING

B-5OPERATIONB-5

23. 415 VAC RECEPTACLEThis is a 415VAC receptacle that provides auxil-iary power. This receptacle has 32 amp ratingand IP66 rated. Refer to the AUXILIARYPOWER RECEPTACLES section in the installa-tion chapter for further information about thesereceptacles. Also refer to the AUXILIARYPOWER OPERATION section later in this chap-ter.

24. GROUND STUD:Provides a connection point for connecting themachine case to earth ground. Refer to“MACHINE GROUNDING” in the Installationchapter for proper machine grounding informa-tion.

25. RCD:“Residual Current Device” provides protectionfrom active to ground contact.

RCD will not protect against electrical shockresulting from contact with active and neutralwires.

26. VRD INDICATOR LIGHTS:Indicates OCV voltage across the output termi-nals. Also indicates operation of VRD in CCmode. A Green light indicates OCV below 30Vand a red light indicates OCV above 30V.

During welding both lights will flash, depending onthe type of Consumable being used.

BATTERY JUMP START TERMINAL(27-28)

27. POSITIVE BATTERY JUMP STARTTERMINAL.

28. NEGATIVE BATTERY JUMP STARTTERMINAL.

12V battery jump start feature is standard.Covered output studs for convenient access, andprotection against accidental impact. can be usedto jump-start a utility truck with up to 800 coldcranking amps. Can also be used to jump-start theVANTAGE® 575 CUMMINS.

29. BATTERY DISCONNECT SWITCHBattery disconnect switch provides lockout/tagoutcapability. Switch is conveniently located on thefront bottom of the machine.

30. AIR CLEANER SERVICE INDICATORAir cleaner service indicator provides a Go/No-Govisual indication of useful filter service life. Alsolocated inside the engine compartment. (SEE FIG-URE B.2)

FIGURE B.2


30

B-6OPERATIONB-6

WHAT ARE VRD AND ROCV DEVICES?VRD’s are gaining popularity as a “must have” safetyaccessory especially where welding applications arebeing carried out in an environment with a high-risk ofelectric shock such as wet areas and hot humidsweaty conditions.

VRD and ROCV are abbreviations for two differentsafety devices used in a welding power source to helpprotect the operator from electric shocks.

VRD stands for “Voltage Reduction Device” andROCV stands for “Reduced Open Circuit Voltage”.Both devices are used as an after market addition orpart of the integral design of a machine. VRD andROCV reduce the voltage at the welding output termi-nals when not welding to a no load voltage of lessthan 35V for DC welding and for AC welding 35V peak25VAC RMS, when the resistance of the output circuitis in the range of 20-200 (ohms). The lower reactiva-tion resistance of the device, the higher the safetylevel and also requires that the welding cable connec-tions be kept in good electrical condition.

Having good electrical connections also limits the pos-sibility of other safety issues such as heat-generateddamage, burns and fires.

WELDING POWER SOURCESWelding power sources generally have an OpenCircuit Voltage (i.e. the voltage at the welding outputterminals when not welding) in the range of 35-115VDC. Welding machines for stick welding(MMAW) and similar constant current (CC mode)processes supply a higher open circuit voltagebetween the electrode and the work when the weldingmachine is switched on and ready to commence weld-ing. These welding machines have high open circuitvoltage (typically 60-80V) then when the arc is estab-lished and welding current is drawn the voltage dropsto 20-35V.

Consequently, the greatest danger occurs when han-dling the electrode and the electrode holder betweenwelding operations, such as when changing elec-trodes.

Welding machines for MIG (GMAW & FCAW) have aflat constant voltage (CV) characteristic, generally witha lower open circuit voltage (30-50V). Also, the cur-rent is turned On and Off by a gun trigger, which alsocontrols the wire feed. Therefore, the welder is notexposed to open circuit voltage unless the trigger isturned on and the wire is feeding. Also, electrodes arenot changed as frequently as for stick welding(MMAW).

VRD/ROCV’s are more commonly incorporated intothe stick welding mode (CC) of the welding machinesbeing used in environments with high-risk of electricshock.

SAFETYThe reduction of the voltage supplies a safer level ofvoltage when an arc is not being struck or when anelectrical resistance less than the welder’s body resis-tance have been detected. All VRD’s are only an aidto safety, personal protective equipment and safeworking practices must be observed at all times. Therisk of electric shock during welding from a correctlyinstalled and maintained welding machine is negligi-ble, provided that sensible precautions are taken bythe user and correct safe working procedures are fol-lowed. All of the welding output circuit should be con-sidered electrically active (hot) and the welder shouldmake sure that they do not become a part of that cir-cuit to ground or they could receive a severe electricshock that could kill. Safe working procedures shouldalways be followed whether a VRD is fitted or not.

VRD OPERATION INDICATOROn the front panel of the VANTAGE® 575 CUMMINSare two indicator lights. A red light when lit indicatesvoltage greater than >30V and a green light when litindicates voltage less than <30V.

These lights monitor the OCV at all times. In the CCmode when the welding arc has stopped the greenl ight will illuminate indicating that the VRD hasreduced the OCV to less than 30V. During welding thered light will illuminate indicating that the OCV isgreater than 30V. During welding the red and greenlight will flash on and off. This is normal operation asthe welding voltage will produce less than 30V,depending on the process and type of electrode beingused.

If the red light remains illuminated after welding in theCC mode, please refer to your local field service shopfor service.

OPERATIONThe low voltage safety features of the VRD’s is toreduce the possibility of electric shock to the operator,a very slight delay during striking of the electrode maybe experienced.

The high voltage that is available on units withoutVRD’s allows them to penetrate and burn throughdirty, painted and heavily mill scale plate. Units fittedwith VRD’s cannot penetrate and are required to reg-ister the correct resistance, which switches the safetydevice into weld mode.


B-7OPERATIONB-7

Unlike other VRD’s Lincoln uses micro processor con-trol to monitor and establish the arc without the stick-ing and shorting of the electrode to the job as seen inmany other VRD installations. Due to the requirementof the resistance in the circuit to be low, for a VRD tooperate, a good metal-to-metal contact must be madebetween the metal core of the electrode and the job.

Any damaged connection anywhere in the output cir-cuit may limit the operation of the VRD. This includesa good connection of the work return clamp and thejob. The work return clamp should be connected closeas practical to where the welding will be performed.

Some electrodes form a cone at the end of the elec-trode after the welding arc has been broken, particu-larly iron powder and low hydrogen electrodes.

This cone will need to be broken off in order to havethe metal core of the electrode to make contact.

STARTING TECHNIQUEThe starting technique that has successfully overcomethe problem is the push, twist, and peel technique.This technique requires the operator to push the elec-trode into the joint and twist.

The Push and Twist breaks off the cone and allowsthe metal electrode to make contact.

The peel and lift of the electrode establishes a con-trolled start to the welding arc. Normal welding tech-nique for the application is then used.

BREAK-IN PERIODThe engine used to supply power for your welder is aheavy duty, industrial engine. It is designed and builtfor rugged use. It is very normal for any engine to usesmall quantities of oil until the break-in is accom-plished. Check the oil level twice a day during thebreak-in period. In general this takes 50 to 100 hoursof operation.

IMPORTANT

IN ORDER TO ACCOMPLISH THIS BREAK-IN, THEUNIT SHOULD BE SUBJECTED TO HEAVYLOADS, WITHIN THE RATING OF THE MACHINE.AVOID LONG IDLE RUNNING PERIODS.

TYPICAL FUEL CONSUMPTIONRefer to Table B.1 for typical fuel consumption of theVANTAGE® 575 CUMMINS Engine for various oper-ating settings.


NOTE: This data is for reference only. Fuel consumption isapproximate and can be influenced by many factors, includ-ing engine maintenance, environmental conditions and fuelquality.

Table B.1Cummins B3.3 Engine Fuel Consumption

Cummins B3.3 Running Time for36Kw(48HP) 94.6L(25GAL.)@1500 RPM (Hours)

Low Idle - 1.6 L/hour 59.5no load 1300 RPM

High Idle - 2.0 L/hour 47.3no load 1590 RPM

DC CC Weld 5.3 L/hour 17.8Output 450Amps @ 38 Volts

Auxiliary Power 4.2 L/hour 21.012,000 V A

20,000 V A 8.0 L/hour 11.8

The VANTAGE® 575 CUMMINS is equipped with therequired R.F. bypass circuitry for the connection ofhigh frequency generating equipment.

The VANTAGE® 575 CUMMINS and any high frequen-cy generating equipment must be properly grounded.See the K930-2 TIG Module operating manuals forcomplete instructions on installation, operation, andmaintenance.

When using the TIG Module, the OUTPUT control onthe VANTAGE® 575 CUMMINS is used to set the max-imum range of the CURRENT CONTROL on the TIGModule or an Amptrol if connected to the TIG Module.

VANTAGE® 575 CUMMINS SETTINGS WHENUSING THE K930-2 TIG MODULE• Set the WELD MODE switch to the “Touch Start Tig 20-

250 Setting”.

• Set the IDLER switch to the “AUTO” position.

• Set the WELDING TERMINALS switch to the “RemotelyControlled” position. This will keep the solid state contactoropen and provide a “cold” electrode until the triggeringdevice (Amptrol or Arc Start Switch) is pressed.

B-8OPERATIONB-8


WELDER OPERATIONDUTY CYCLEDuty Cycle is the percentage of time the load is beingapplied in a 10 minute period. For example a 60%duty cycle, represents 6 minutes of load and 4minutes of no load in a 10 minute period.

STICK WELDING MODEThe VANTAGE® 575 CUMMINS can be used with abroad range of DC stick electrodes. The MODE switchprovides two stick welding settings as follows:

CC-STICK MODEThe CC-STICK position of the MODE switch isdesigned for horizontal, vertical-up and over headwelding with all types of electrodes, especially lowhydrogen. The OUTPUT CONTROL knob adjusts thefull output range for stick welding.

The ARC CONTROL knob sets the short circuit (arc-force) current during stick welding. Increasing thenumber from -10(Soft) to +10 (Crisp) increases theshort circuit current and prevents sticking of the elec-trode to the plate while welding. This can alsoincrease spatter. It is recommended that the ARCCONTROL be set to the minimum number withoutelectrode sticking. Start with the knob set at 0.

TOUCH START TIG MODEThe VANTAGE® 575 CUMMINS can be used in a widevariety of DC TIG welding applications.

The TOUCH START TIG setting of the MODE switchis for DC TIG (Tungsten Inert Gas) welding. To initiatea weld, the OUTPUT CONTROL knob is first set tothe desired current and the tungsten is touched to thework. During the time the tungsten is touching thework there is very little voltage or current and, in gen-eral, avoids tungsten contamination. Then, the tung-sten is gently lifted off the work in a rocking motion,which establishes the arc.

To stop the arc, simply lift the TIG torch away from thework piece. When the arc voltage reaches approxi-mately 30 volts, the arc will go out and the machinewill automatically reset to the touch start current level.The tungsten may then be retouched to the workpiece to restrike the arc. The arc may also be startedand stopped with an Amptrol or Arc Start Switch.

The ARC CONTROL is not active in the TIG mode.

In general the ‘Touch Start’ feature avoids tungstencontamination without the use of a Hi-frequency unit.If the use of a high frequency generator is desired, theK930-2 TIG Module can be used with the VANTAGE®575 CUMMINS. The settings are for reference.

ARC GOUGINGFor optimal performance when arc gouging, set theVANTAGE® 575 CUMMINS “WELD MODE” switch tothe “CC - STICK” position, and the “ARC CONTROL”to 10.

Set the “OUTPUT” knob to adjust output current to thedesired level for the gouging electrode being usedaccording to the ratings in the following Table B.2

NOTE: If desired the CV mode can be used for Arc Gouging.

* Maximum current setting is limited to the VANTAGE® 575 CUMMINS maxi-mum of 575 Amps.

WIRE WELDING-CVConnect a wire feeder to the VANTAGE® 575 CUM-MINS according to the instructions in INSTALLATIONINSTRUCTIONS Section.

The VANTAGE® 575 CUMMINS in the ”CV-WIRE”position, permits it to be used with a broad range offlux cored wire (Innershield and Outershield) elec-trodes and solid wires for MIG welding (gas metal arcwelding). Welding can be finely tuned using the “ARCCONTROL”. Turning the ARC CONTROL clockwisefrom -10(soft) to +10(crisp) changes the arc from softand washed-in to crisp and narrow. It acts as aninductance/pinch control.

The proper setting depends on the procedure andoperator preference. Start with the knob set at 0.

For any electrodes, including the above recommenda-tions, the procedures should be kept within the ratingof the machine. For additional electrode information,See www.lincolnelectric.com or the appropriateLincoln publication.

Carbon Diameter Current Range (DC, elec-trode positive)

1/8"(3.2mm) 30-60 Amps5/32"(4.0mm) 90-150 Amps3/16"9(4.8mm) 200-250 Amps1/4"(6.4mm) 300-400 Amps5/16"(8.0mm) 350-450 Amps3/8"(10.0mm) 450-575 Amps*

TABLE B.2

B-9OPERATIONB-9


Table B.3 TYPICAL CURRENT RANGES (1) FOR TUNGSTEN ELECTRODES (2)

DCEN (-) DCEP (+) Approximate Argon Gas Flow Ratel/min (c.f.m.)

TungstenElectrode 1%, 2% 1%, 2% TIG TORCHDiameter Thoriated Thoriated Aluminium Stainless Steel Nozzlemm (in) Tungsten Tungsten Size (4), (5)

.25 (0.010) 2-15 (3) 2-4 (3-8) 2-4 (3-8) #4, #5, #6

.50 (0.020) 5-20 (3) 3-5 (5-10) 3-5 (5-10)

1.0 (0.040) 15-80 (3) 3-5 (5-10) 3-5 (5-10)

1.6 (1/16) 70-150 10-20 3-5 (5-10) 4-6 (9-13) #5, #6

2.4 (3/32) 150-250 15-30 6-8 (13-17) 5-7 (11-15) #6, #7, #83.2 (1/8) 250-400 25-40 7-11 (15-23) 5-7 (11-15)

4.0 (5/32) 400-500 40-55 10-12 (21-25) 6-8 (13-17) #8, #104.8 (3/16) 500-750 55-80 11-13 (23-27) 8-10 (18-22)

6.4 (1/4) 750-1000 80-125 13-15 (28-32) 11-13 (23-27)

(1) When used with argon gas. The current ranges shown must be reduced when using argon/helium or pure helium shielding gases.

(2) Tungsten electrodes are classified as follows by the American Welding Society (AWS):

Pure EWP1% Thoriated EWTh-12% Thoriated EWTh-2

Though not yet recognized by the AWS, Ceriated Tungsten is now widely accepted as a substitute for 2% Thoriated Tungsten in AC and DC applica-tions.

(3) DCEP is not commonly used in these sizes.

(4) TIG torch nozzle “sizes” are in multiples of 1/16ths of an inch:

# 4 = 1/4 in. 6 mm# 5 = 5/16 in. 8 mm# 6 = 3/8 in. 10 mm# 7 = 7/16 in. 11 mm# 8 = 1/2 in. 12.5 mm#10 = 5/8 in. 16 mm

(5) TIG torch nozzles are typically made from alumina ceramic. Special applications may require lava nozzles, which are less prone to breakage, but can-not withstand high temperatures and high duty cycles.

PARALLELINGWhen paralleling machines in order to combine theiroutputs, all units must be operated in the CC-STICKmode only at the same output settings. To achievethis, turn the WELD MODE switch to the CC-STICKposition. Operation in other modes may produce errat-ic outputs, and large output imbalances between theunits.

AUXILIARY POWER OPERATION

Start the engine and set the IDLER control switch tothe desired operating mode. Full power is availableregardless of the welding control settings, if no weld-ing current is being drawn.

The auxiliary power of the VANTAGE® 575 CUM-MINS consists of two 15 Amp-240V single phasereceptacles and one 32amp-415V 3 phase receptacle.

The auxiliary power capacity is 7,200 watts of 50 Hz,single phase power or 20,000 watts of 50Hz, threephase power. The auxiliary power capacity rating inwatts is equivalent to volt-amperes at unity power fac-tor. The maximum permissible current of the 415 VACoutput is 32 A.Output voltage is within ±10% at allloads up to rated capacity.

NOTE: The 240V receptacles are connected to differ-ent phases and cannot be paralleled.

The auxiliary power receptacles should only be usedwith three wire, four wire or fire wire earth type plugsor approved double insulated tools with two wireplugs.

The current rating of any plug used with the systemmust be at least equal to the current capacity of theassociated receptacle.

SIMULTANEOUS WELDING ANDAUXILIARY POWER LOADS

It must be noted that the above auxiliary power ratingsare with no welding load. Simultaneous welding andpower loads are specified in table B.4. The permissi-ble currents shown assume that current is beingdrawn from either the 240 VAC or 415 VAC supply(not both at the same time).

VANTAGE® 575 CUMMINS Extension Cord Length Recommendations(Use the shortest length extension cord possible sized per the following table.)


B-10OPERATIONB-10

TABLE B.5

TABLE B.4 VANTAGE® 575 CUMMINS SIMULTANEOUS WELDING AND POWER LOADS

WELDINGOUTPUT

500A/40V350A/34V200A/30V150A/26V90A/24V

0

PERMISSIBLEPOWER-WATTS

(Unity Power Factor)

08,10012,00016,00018,00020,000

@ 240V ±10%*

040*30*30*30*30*

@ 415V ±10%

014 amp/phase

18.5 amp/phase23.6 amp/phase26.4 amp/phase32 amp/phase

Maximum Allowable Cord Length in m (ft.) for Conductor Size

Conductor size is based on maximum 2.0% voltage drop.

2.52mm 14AWG 4.02mm 12AWG 6.02mm 10AWG 10.02mm 8AWG 16.02mm 6AWG 25.02mm 4AWGLoad

(Watts)

3,600

4,800

Current(Amps)

15

20

Voltage(Volts)

240

240

18 (60) 23

18

(75)

(60)

46

30

(150)

(100)

69

53

(225)

(175)

107

84

(350)

(275)

183

137

(600)

(450)

Permissible AuxiliaryCurrent in Amperes

* Each receptacle is limited to 15 amps.

K2354-1 AIR DRYER KIT - Minimizes water contentin supply air. Avoids cold weather air hose ice up.

K2356-1 CONTROL PANEL COVER KIT - Clearplexiglass cover to protect control panel from dirt anddebris, and to visually monitor machine operation.Lockable to deter vandalism.

K2340-1 LOCKABLE FUEL CAP / FLASHARRESTER KIT - For use in locations where flasharrester safety is required. Lockable fuel cap preventstampering with fuel. Green cap color provides a visualreminder to use diesel when refueling.

K2359-1 COLD WEATHER HEATER AND TARP KIT- For extreme cold conditions where normal enginestarting is not sufficient. Includes oil pan heater,engine water heater and radiator grill tarp.

TIG OPTIONSK870 FOOT AMPTROL® - Varies current while weld-ing for making critical TIG welds and crater filling.Depress pedal to increase current. Depressing pedalfully achieves maximum set current. Fully raising thepedal finishes the weld and starts the afterflow cycleon systems so equipped. Includes 25 ft. (7.6m) controlcable.

K963-3 HAND AMPTROL® - Varies current for mak-ing critical TIG welds. Fastens to the torch for conve-nient thumb control. Comes with a 25 ft. (7.6m) cable.(for larger handle 18 or 26 series torches)

C-1ACCESSORIESC-1


OPTIONAL FIELD INSTALLEDACCESSORIES

K857 25 ft. (7.5 m) or K857-1 100 ft. (30.4 m)REMOTE CONTROL - Portable control providessame dial range as the output control on the welderfrom a location up to the specified length from thewelder. Has convenient plug for easy connection tothe welder. The VANTAGE® 575 CUMMINS isequipped with a 6-pin connector for connecting theremote control.

K704 ACCESSORY SET - Includes 35 feet (10 m) ofelectrode cable and 30 feet (9 m) of work cable, head-shield, filter plate, work clamp and electrode holder.Cable is rated at 500 amps, 60% duty cycle.

K2641-2 FOUR WHEELED STEERABLE YARDTRAILERFor in plant and yard towing. Comes standard with aDuo-Hitch™, a 2” Ball and Lunette Eye combinationHitch.

K2636-1 TRAILER - Two-wheeled trailer with optionalfender and light package. For highway use, consultapplicable federal, state, and local laws regardingpossible additional requirements. Comes standardwith a Duo-Hitch™, a 2” Ball and Lunette Eye combi-nation hitch. A fender & a light package. Order:K2636-1 Trailer K2639-1 Fender & Light KitK2640-1 Cable Storage Rack

K887-1 ETHER START KIT - Provides maximum coldweather starting assistance for frequent starting below10°(-12°C). Required Ether tank is not provided withkit.

K1847-1 SPARK ARRESTOR KIT - Easily mounts tostandard muffler.

Pipe Thawing with an arc welder can cause fire,explosion, damage to electric wiring or to the arcwelder if done improperly. The use of an arcwelder for pipe thawing is not approved by theCSA, nor is it recommended or supported byLincoln Electric.

------------------------------------------------------------------------

WARNING

D-1MAINTENANCED-1


SAFETY PRECAUTIONS

• Have qualified personnel do all maintenanceand troubleshooting work.

• Turn the engine off before working inside themachine or servicing the engine.

• Remove guards only when necessary toperform maintenance and replace them whenthe maintenance requiring their removal iscomplete. If guards are missing from themachine, obtain replacements from a LincolnDistributor. (See Operating Manual Parts List.)

Read the Safety Precautions in the front of thismanual and in the Engine Owner’s Manual beforeworking on this machine.

Keep all equipment safety guards, covers, anddevices in position and in good repair. Keephands, hair, clothing, and tools away from thegears, fans, and all other moving parts whenstarting, operating, or repairing the equipment.------------------------------------------------------------ROUTINE AND PERIODIC MAINTENANCE

DAILY• Check the Engine oil levels .• Refill the fuel tank to minimize moisture condensa-

tion in the tank.• Check water separator for water and drain if neces-

sary.• Check coolant level.

WEEKLYBlow out the machine with low pressure air periodical-ly. In particularly dirty locations, this may be requiredonce a week.

ENGINE MAINTENANCERefer to the “Periodic Checks” section of the EngineOperator’s Manual for the recommended maintenanceschedule of the following:

a) Engine Oil and Filterb) Air Cleanerc) Fuel Filter - and Delivery Systemd) Alternator Belte) Batteryf ) Cooling System

Refer to Table D.1 at the end of this section for vari-ous engine maintenance components.

WARNING

AIR FILTER

• Excessive air filter restriction will result inreduced engine life.

• Never use gasoline or low flash point solventsfor cleaning the air cleaner element. A fire orexplosion could result.

• Never run the engine without the air cleaner.Rapid engine wear will result from contaminants,such as dust and dirt being drawn into theengine.

---------------------------------------------------------------------The diesel engine is equipped with a dry type air filter.Never apply oil to it. Service the air cleaner as follows:

Replace the element as indicated by the service indi-cator. (See Service Instructions and Installation Tipsfor Engine Air Filter.)

CAUTION

CAUTION

WARNING

D-2MAINTENANCED-2


Unfasten or unlatch theservice cover. Becausethe filter fits tightly over theoutlet tube to create the critical seal, there willbe some initial resistance, similar to breakingthe seal on a jar. Gently move the end of the filterback and forth to break the seal then rotate whilepulling straight out. Avoid knocking the filteragainst the housing.

Remove the FilterRemove the Filter

Rotate thefilter whilepullingstraight out.

If your air cleaner has a safety filter, replace it every third primaryfilter change. Remove the safety filter as you would the primaryfilter. Make sure you cover the air cleaner outlet tube to avoid anyunfiltered contaminant dropping into the engine.

If your air cleaner is equipped with a Vacuator ValveVisually check and physically squeeze to make sure thevalve is flexible and not inverted, damaged or plugged.

Inspect the new filter carefully, paying attention tothe inside of the open end, which is thesealing area. NEVER install a damagedfilter. A new Donaldson radial sealfilter may have a dry lubricant on theseal to aid installation.

If you're servicing the safety filter, this should be seated intoposition before installing the primary filter.

Insert the new filter carefully. Seat the filter by hand, making certain it iscompletely into the air cleaner housingbefore securing the cover in place.

If the service cover hits the filter before it is fully in place, removethe cover and push the filter (by hand) further into the air cleanerand try again. The cover should go on with no extra force.

Once the filter is in place, secure the service cover.

Make sure that all mounting bands, clamps, bolts, and connectionsin the entire air cleaner system are tight. Check for holes in pipingand repair if needed. Any leaks in your intake piping will send dustdirectly to the engine!

The critical sealing area will stretchslightly, adjust itself and distribute the sealing pressure evenly. Tocomplete a tight seal, apply pressure by hand at the outer rim ofthe filter, not the flexible center. (Avoid pushing on the center of theurethane end cap.) No cover pressure is required to hold the seal.NEVER use the service cover to push the filter into place! Using thecover to push the filter in could cause damage to the housing, coverfasteners and will void the warranty.

Visually inspect the old filter for any signsof leaks. A streak of dust on the clean sideof the filter is a telltale sign. Remove anycause of leaks before installing new filter.

Clean Both Surfaces of the Outlet TubeClean Both Surfaces of the Outlet Tubeand Check the Vacuator™ Valveand Check the Vacuator™ Valve

Inspect the OldInspect the OldFilter for Leak CluesFilter for Leak Clues

Inspect the New Filter for DamageInspect the New Filter for Damage

Insert the New Radial Seal Filter ProperlyInsert the New Radial Seal Filter Properly

Check Connectors for Tight FitCheck Connectors for Tight Fit

NEVER use the service cover toNEVER use the service cover topush the filter into place! Usingpush the filter into place! Usingthe cover to push the filter in couldthe cover to push the filter in couldcause damage to the housing, covercause damage to the housing, coverfasteners and will void the warranty.fasteners and will void the warranty.

CautionCaution

Use a clean cloth to wipe the filter sealing surface and the inside ofthe outlet tube. Contaminant on the sealing surface could hinder aneffective seal and cause leakage. Make sure that all contaminant isremoved before the new filter is inserted. Dirt accidently transferredto the inside of the outlet tube will reach the engine and cause wear. Engine manufacturers say that it takes only a few grams ofdirt to "dust" an engine! Be careful not to damage the sealing areaon the tube.

Wipe both sidesof the outlettube clean.

Outer edge of theoutlet tube

Inner edge of theoutlet tube

Service InstructionsService InstructionsSingle- and Two-Stage Engine Air CleanersSingle- and Two-Stage Engine Air Cleaners

D-3MAINTENANCED-3

FUEL FILTERS

When working on the fuel system:

• Keep naked lights away, do not smoke !

• Do not spill fuel !

-------------------------------------------------------------------------

The VANTAGE® 575 CUMMINS is equipped with aFuel Filter located after the lift pump and before fuelinjectors.The procedure for changing the filter is as fol-lows.

1. Close the fuel shutoff valve.

2. Clean the area around the fuel filter head. Removethe filter. Clean the gasket surface of the filter headand replace the o-ring.

3. Fill the clean filter with clean fuel, and lubricate theo-ring seal with clean lubricating oil.

4. Install the filter as specified by the filter manufactur-er.

Mechanical overtightening will distort the threads,filter element seal or filter can.

-------------------------------------------------------------------------

COOLING SYSTEMThe VANTAGE® 575 CUMMINS is equipped with apressure radiator. Keep the radiator cap tight to pre-vent loss of coolant. Clean and flush the coolant sys-tem periodically to prevent clogging the passage andover-heating the engine. When antifreeze is needed,always use the permanent type.

BATTERY HANDLINGGASES FROM BATTERY can explode.

• Keep sparks, flame and cigarettesaway from battery.

To prevent EXPLOSION when:

• INSTALLING A NEW BATTERY - dis-connect negative cable from old bat-tery first and connect to new batterylast.

• CONNECTING A BATTERY CHARGER- Remove battery from welder by dis-connecting negative cable first, thenpositive cable and battery clamp.When reinstalling, connect negativecable last. Keep well ventilated.

• USING A BOOSTER - connect positivelead to battery first then connect nega-tive lead to engine foot.

BATTERY ACID CAN BURN EYES ANDSKIN.

• Wear gloves and eye protection andbe careful when working near battery.Follow instructions printed on battery.

-------------------------------------------------------------------------PREVENTING ELECTRICAL DAMAGE1. When replacing, jumping, or otherwise connecting

the battery to the battery cables, the proper polaritymust be observed. Failure to observe the properpolarity could result in damage to the charging cir-cuit. The positive (+) battery cable has a red termi-nal cover.

2. If the battery requires charging from an externalcharger, disconnect the negative battery cable firstand then the positive battery cable before attachingthe charger leads. Failure to do so can result indamage to the internal charger components. Whenreconnecting the cables, connect the positive cablefirst and the negative cable last.

PREVENTING BATTERY DISCHARGETurn the RUN/STOP switch to stop when engine isnot running.

PREVENTING BATTERY BUCKLINGTighten nuts on battery clamp until snug.


WARNING

WARNING

D-4MAINTENANCED-4

CHARGING THE BATTERYWhen you charge, jump, replace, or otherwise connectbattery cables to the battery, be sure the polarity iscorrect. Improper polarity can damage the chargingcircuit. The VANTAGE® 575 CUMMINS positive (+)battery terminal has a red terminal cover.

If you need to charge the battery with an externalcharger, disconnect the negative cable first, then thepositive cable before you attach the charger leads.after the battery is charged, reconnect the positive bat-tery cable first and the negative cable last. Failure todo so can result in damage to the internal chargercomponents.

Follow the instructions of the battery charger manufac-turer for proper charger settings and charging time.

NAMEPLATES / WARNING DECALS MAIN-TENANCEWhenever routine maintenance is performed on thismachine - or at least yearly - inspect all nameplatesand labels for legibility. Replace those which are nolonger clear. Refer to the parts list for the replacementitem number.

WELDER / GENERATOR MAINTE-NANCE

STORAGEStore the VANTAGE® 575 CUMMINS in a clean, dryprotected areas.

CLEANINGBlow out the generator and controls periodically withlow pressure air. Do this at least once a week in par-ticularly dirty areas.

BRUSH REMOVAL AND REPLACEMENTIt is normal for the brushes and slip rings to wear anddarken slightly. Inspect the brushes when a generatoroverhaul is necessary.

Do not attempt to polish slip rings while theengine is running.

------------------------------------------------------------------------


WARNING

Table D.1 Engine Maintenance Components

ITEM MAKE PART NUMBER SERVICE INTERVAL

Air Cleaner Element Donaldson P822768 Replace as indicated byService Indicator

Fleetguard AF25436

Oil Filer Cummins C6002112110 Replace every 750 hours or 3 months,Fleetguard LF16011 whichever is less.

Fan Belt Cummins C0412021749 Inspect every 1000 hours or 12 months,whichever is less.

Fuel Strainer Cummins 3826094 Inspect and replace monthly asFleetguard FF5079 required. Replace annually.

Fuel Filter / Fleetguard FS19594 Replace every 500 hours or 6 months,Water Separator whichever is less.

Battery ----- BCI GROUP 34 Inspect every 500 hours

Engine Oil Change See Manual ----- Change every 750 hours or 3 months,whichever is less. Check daily.

E-1TROUBLESHOOTINGE-1


If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact yourLocal Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

CAUTION

This Troubleshooting Guide is provided to help youlocate and repair possible machine malfunctions.Simply follow the three-step procedure listed below.

Step 1. LOCATE PROBLEM (SYMPTOM).Look under the column labeled “PROBLEM (SYMP-TOMS)”. This column describes possible symptomsthat the machine may exhibit. Find the listing thatbest describes the symptom that the machine isexhibiting.

Step 2. POSSIBLE CAUSE.The second column labeled “POSSIBLE CAUSE” liststhe obvious external possibilities that may contributeto the machine symptom.

Step 3. RECOMMENDED COURSE OF ACTIONThis column provides a course of action for thePossible Cause, generally it states to contact yourlocal Lincoln Authorized Field Service Facility.

If you do not understand or are unable to perform theRecommended Course of Action safely, contact yourlocal Lincoln Authorized Field Service Facility.

HOW TO USE TROUBLESHOOTING GUIDE

Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.Unauthorized repairs performed on this equipment may result in danger to the technician andmachine operator and will invalidate your factory warranty. For your safety and to avoid ElectricalShock, please observe all safety notes and precautions detailed throughout this manual.

__________________________________________________________________________

WARNING



Observe all Safety Guidelines detailed throughout this manual


CAUTION

PROBLEMS(SYMPTOMS)

POSSIBLECAUSE

RECOMMENDEDCOURSE OF ACTION

Major Physical or Electrical Damageis Evident.

Engine will not crank

Engine will crank but not start.

Engine shuts down shortly after starting.

Engine shuts down while under a load.

Engine runs rough.

Engine will not shut off.

1. Contact your local LincolnAuthorized Field ServiceFacility.

1. Battery low.

2. Loose battery cable connectionswhich may need Inspected, cleanedor tighten.

3. Faulty wiring in engine starting circuit.

4. Faulty engine starter. Contact autho-rized local Engine Service Shop.

5. Battery disconnect switch is in the offposition.

1. Out of fuel.

2. Fuel shut off valve is in the off posi-tion make sure the valve lever is in avertical direction.

3. Engine shut down solenoid not pullingin.

4. On/Off switch on for more than 30sec. before starting, the On/Off switchwill need to be switch off and turnedback on.

5. Fuel Filters dirty/clogged, main filterelement and/or In-line Fuel Filter mayneed to be replaced.

6. High water temperature or low oilpressure. (engine protection light lit)

1. Low oil pressure (engine protectionlight lit). Check oil level (Consultengine service dealer).

2. High water temperature. Checkengine cooling system. (engine pro-tection light lit).

3. Faulty oil pressure switch.

4. Faulty water temperature switch.Contact authorized local EngineService Shop.

1. High water temperature.

1. Dirty fuel or air f i l ters may needcleaned/replaced.

2. Water in fuel.

1. Fuel Shutdown solenoid not function-ing properly / linkage binding.

If all recommended possible areasof misadjustment have beenchecked and the problem persists,Contact your local LincolnAuthorized Field Service Facility.

E-3TROUBLESHOOTINGE-3Observe all Safety Guidelines detailed throughout this manual


CAUTION

PROBLEMS(SYMPTOMS)

POSSIBLECAUSE


Battery does not stay charged.

Engine will not idle down to lowspeed.

Engine will not go to high idle whenattempting to weld.

Engine will not go to high idle whenusing auxiliary power.

1. Faulty battery . 2. Faulty engine alternator. 3. Loose or broken lead in charging

circuit. 4. Loose fan belt may need tighten-

ing.

1. Idler switch in HIGH idle position,make sure switch is set to AUTO.

2. External load on welder or auxil-iary power.

3. Mechanical problem in idler sole-noid linkage.

4. Faulty wiring in solenoid circuit. 5. No or low voltage @ idle solenoid 6. Faulty idler solenoid. 7. Faulty, Weld Control PCB

(Printed Circuit Board), Pull Coil/Battery PCB

1. Poor work lead connection towork.

2. Broken idler solenoid spring.3. Welding Terminals switch in

wrong position. 4. No open circuit voltage at output

studs. 5. Faulty, Pull Coil/Battery PCB or

Weld Control PCB.

1. Broken wire in auxiliary currentsensor wiring.

2. Auxiliary power load is less than100 watts.

3. Faulty Pull Coil/Battery PCB orWeld Control PCB.

If all recommended possible areas ofmisadjustment have been checkedand the problem persists, Contactyour local Lincoln AuthorizedField Service Facility.




Observe all Safety Guidelines detailed throughout this manual


CAUTION

PROBLEMS(SYMPTOMS)

POSSIBLECAUSE


Engine goes to low idle but does notstay at low idle.

No welding output or auxiliary output.

Welder has some/ no output and nocontrol. Auxiliary output OK

No welding output. Auxiliary outputOK.

No auxiliary power.

1. Faulty Peripheral PCB, PullCoil/Battery PCB or WeldControl PCB.

1. Broken lead in rotor circuit.2. Faulty field diode module. 3. Faulty Weld Control PCB. 4. Faulty rotor.

1. Faulty remote kit. 2. Faulty output control potentiome-

ter. 3. Faulty output control wiring.4. Faulty Weld Control PCB, Pull

Coil/Battery PCB or ChopperPCB.

1. WELDING TERMINALS switchin wrong position, be sure switchis in WELDING TERMINALSALWAYS ON position.

2. Faulty Weld Control PCB, PullCoil/Battery PCB or ChopperPCB.

1. RCD may have tripped. 2. Open breakers may need to be

reset. 3. Faulty receptacle. 4. Faulty auxiliary circuit wiring.

If all recommended possible areasof misadjustment have beenchecked and the problem persists,Contact your local LincolnAuthorized Field Service Facility.

F-1WIRING DIAGRAMF-1


NO

TE

: T

his

dia

gra

m is

fo

r re

fere

nce

on

ly.

It m

ay n

ot

be

accu

rate

fo

r al

l mac

hin

es c

ove

red

by

this

man

ual

. T

he

spec

ific

dia

gra

m f

or

a p

arti

cula

r co

de

is in

clu

ded

wit

h t

he

mac

hin

e. I

f th

e d

iag

ram

is il

leg

ible

, wri

te t

o t

he

Ser

vice

Dep

artm

ent

for

a re

pla

cem

ent.

Giv

e th

e eq

uip

men

t co

de

nu

mb

er.

F-2DIAGRAMSF-2


F-3DIAGRAMSF-3


GN

D

75 76 77

GR

EE

N

K29

1 O

R K

404

75

INP

UT

CA

BLE

76

N.E

.

77K

775

OP

TIO

NA

LR

EM

OT

E C

ON

TR

OL

DAM

AGED

. THE

ENG

INE

GO

VERN

OR

SETT

ING

IS P

RE-S

ET A

T TH

E FA

CTO

RY -

DO N

OT

ADJU

ST A

BOVE

RPM

SPE

CIFI

CATI

ONS

LIS

TED

IN

81 42 41

3131

3232

22

44

2121

GN

D

82

N.D

.LN

-7W

IRE

FE

ED

ER

Kee

p gu

ards

in p

lace

.

EN

GIN

E W

EL

DE

RS

/ K

867

/ K

775

/ L

N-7

CO

NN

EC

TIO

N D

IAG

RA

M

Kee

p aw

ay fr

om m

ovin

g pa

rts.

WA

RN

ING

Onl

y qu

alifi

ed p

erso

nnel

sho

uld

inst

all,u

se

or s

ervi

ce th

is e

quip

men

t.

SP

AR

E

Do

not o

pera

te w

ith p

anel

s op

en.

7-20

00

S

2398

3

Dis

conn

ect N

EG

AT

IVE

(-)

BA

TT

ER

Y L

EA

D

EL

EC

TR

OD

E

ELE

CT

RO

DE

CA

BLE

TO

WIR

E F

EE

D U

NIT

K86

7 U

NIV

ER

SA

L

AD

AP

TE

R P

LUG

CAUT

ION

:

ANY

INCR

EASE

OF

THE

HIG

H ID

LE E

NGIN

E RP

M B

Y CH

ANG

ING

THE

GO

VERN

OR

SETT

ING

OR

OVE

RRID

ING

THE

THR

OTT

LE L

INKA

GE

WIL

L CA

USE

AN IN

CREA

SE IN

THE

THE

AC

AUXI

LIAR

Y VO

LTAG

E. IF

THI

S VO

LTAG

E G

OES

OVE

R 14

0 VO

LTS,

WIR

E FE

EDER

CO

NTRO

L CI

RCUI

TS M

AY B

E

THE

ENG

INE

WEL

DER

OPE

RATI

NG M

ANUA

L.

N.A

. W

ELD

ING

CA

BLE

MU

ST

BE

OF

PR

OP

ER

CA

PA

CIT

Y F

OR

TH

E C

UR

RE

NT

AN

D D

UT

Y C

YC

LE O

F IM

ME

DIA

TE

AN

D F

UT

UR

E

A

PP

ILIC

AT

ION

S. S

EE

OP

ER

AT

ING

MA

NU

AL.

PLA

CE

WIR

E F

EE

DE

R S

WIT

CH

TO

"W

IRE

FE

ED

ER

WIT

H C

ON

TR

OL

CA

BLE

PO

SIT

ION

.

N.B

. U

SE

VO

LTM

ET

ER

SW

ITC

H T

O S

ELE

CT

DE

SIR

ED

ELE

CT

RO

DE

PO

LAR

ITY.

PO

SIT

ION

TH

E "

SE

LEC

TO

R"

SW

ITC

H T

O "

WIR

E W

ELD

ING

CV

".

N.C

. IF

OP

TIO

NA

L R

EM

OT

E O

UT

PU

T C

ON

TR

OL

IS U

SE

D,C

ON

TR

OL

IS A

UT

OM

AT

ICA

LLY

SW

ITC

HE

D T

O R

EM

OT

E C

ON

TR

OL.

N.D

. IN

SU

LAT

E E

AC

H U

NU

SE

D L

EA

D IN

DIV

IDU

ALL

Y.

N.E

. S

PLI

CE

LE

AD

S A

ND

INS

ULA

TE

.

}be

fore

ser

vici

ng.

Do

not t

ouch

ele

ctric

ally

live

par

ts.

}1

4 P

INA

MP

HE

NO

L

TO

WO

RK

TO

WO

RK

F-4DIAGRAMSF-4


F-5DIAGRAMSF-5


F-6DIAGRAMSF-6


CA

UT

ION

:

N.A

. W

ELD

ING

CA

BLE

MU

ST

BE

OF

PR

OP

ER

CA

PA

CIT

Y F

OR

TH

E C

UR

RE

NT

AN

D D

UT

Y C

YC

LE O

F IM

ME

DIA

TE

AN

D F

UT

UR

E

AP

PIC

AT

ION

S. S

EE

OP

ER

AT

ING

MA

NU

AL.

7532314142

N.C

. IN

SU

LAT

E E

AC

H U

NU

SE

D L

EA

D IN

DIV

IDU

ALL

Y.

N.D

. S

PLI

CE

LE

AD

S A

ND

INS

ULA

TE

.

THE

ENG

INE

WEL

DER

OPE

RATI

NG M

ANUA

L.

GN

D

31 4 21 B CA

14 P

INA

MP

HE

NO

L

TO

WO

RK

TO

WO

RK

ELE

CT

RO

DE

TO

WIR

E F

EE

D U

NIT

ELE

CT

RO

DE

CA

BLE

WIR

E

FE

ED

ER

K19

6K

867

UN

IVE

RS

AL

AD

AP

TE

R P

LUG

INP

UT

CA

BLE

S

2398

9

E

NG

INE

WE

LD

ER

S /

K86

7 / L

N-8

CO

NN

EC

TIO

N D

IAG

RA

M

7-20

00

2 4 76 77

ANY

INCR

EASE

OF

THE

HIG

H ID

LE E

NGIN

E RP

M B

Y CH

ANG

ING

THE

GO

VERN

OR

SETT

ING

OR

OVE

RRID

ING

THE

THR

OTT

LE L

INKA

GE

WIL

L CA

USE

AN IN

CREA

SE IN

THE

THE

AC

AUXI

LIAR

Y VO

LTAG

E. I

F TH

IS V

OLT

AGE

GO

ES O

VER

140

VOLT

S, W

IRE

FEED

ER C

ONT

ROL

CIRC

UITS

MAY

BE

DAM

AGED

. THE

ENG

INE

GO

VERN

OR

SETT

ING

IS P

RE-S

ET A

T TH

E FA

CTO

RY -

DO N

OT

ADJU

ST A

BOVE

RPM

SPE

CIFI

CATI

ONS

LIS

TED

IN

N.B

. U

SE

VO

LTM

ET

ER

SW

ITC

H T

O S

ELE

CT

DE

SIR

ED

ELE

CT

RO

DE

PO

LAR

ITY.

PO

SIT

ION

TH

E S

ELE

CT

OR

SW

ITC

H T

O "

WIR

E W

ELD

ING

CV

".

SP

AR

E

82

Onl

y qu

alifi

ed p

erso

nnel

sho

uld

inst

all,u

se

81

befo

re s

ervi

cing

.

or s

ervi

ce th

is e

quip

men

t.

Kee

p aw

ay fr

om m

ovin

g pa

rts.

N.C

.

Kee

p gu

ards

in p

lace

.

}D

isco

nnec

t NE

GA

TIV

E (

-) B

AT

TE

RY

LE

AD

Do

not t

ouch

ele

ctric

ally

live

par

ts.

21

Do

not o

pera

te w

ith p

anel

s op

en.

GN

D

N.D

.

32 2

WA

RN

ING

}

LN-8

F-7DIAGRAMSF-7


F-8DIAGRAMSF-8


F-9DIAGRAMSF-9


F-10DIAGRAMSF-10


F-11DIAGRAMSF-11


2

9/03

F-12DIAGRAMSF-12


F-13DIMENSION PRINTF-13


*

*

*

*

BOTT

OM

VVIE

W OO

F WW

ELDE

R BBA

SE.

N.A

. . CCE

NTETE

R OO

F G

RG

RAVI

TYTY WW

ITH

OOIL

I IN EE

NGIN

E, EE

MPT

Y FFU

EL T

ATANKK

AAND

COCO

OLA

NTT

I IN RR

ADIA

TATO

R.

M18

962-

3B

2.24

5656.9

5.86

148

148.

8

4545.6

711

611

60

3131.5

080

080

0.1

4242.0

010

6610

66.8

4646.3

511

7711

77.3

3232.0

881

481

4.8

3333.5

385

185

1.7

4242.3

510

7510

75.7

5050.1

512

7312

73.8

1616.8

54242

8

6363.1

016

0216

02.7

6.56

166

166.

6

6.55

166

166.

4

1414.6

337

137

1.6

3737.3

094

794

7.4

4545.3

811

5211

52.7

2828.9

973

673

6.3

1919.6

349

849

8.6

2323.6

960

160

1.7

5050.3

812

7912

79.7

5454.4

413

8213

82.8

6.53

165

165.

92424.9

763

463

4.2

*TRAI

LER

MMO

UO

UNTI

NG HH

OLE

LLO

CATAT

ION

ONS

.

4848.9

212

4212

42.6

WARNING

AVISO DEPRECAUCION

ATTENTION

WARNUNG

ATENÇÃO

Spanish

French

German

Portuguese

Japanese

Chinese

Korean

Arabic

READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BEUSED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.

SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOSCONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.

LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS AETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.

LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER-STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.

● Do not touch electrically live parts orelectrode with skin or wet clothing.

● Insulate yourself from work andground.

● No toque las partes o los electrodosbajo carga con la piel o ropa moja-da.

● Aislese del trabajo y de la tierra.

● Ne laissez ni la peau ni des vête-ments mouillés entrer en contactavec des pièces sous tension.

● Isolez-vous du travail et de la terre.

● Berühren Sie keine stromführendenTeile oder Elektroden mit IhremKörper oder feuchter Kleidung!

● Isolieren Sie sich von denElektroden und dem Erdboden!

● Não toque partes elétricas e elec-trodos com a pele ou roupa molha-da.

● Isole-se da peça e terra.

● Keep flammable materials away.

● Mantenga el material combustiblefuera del área de trabajo.

● Gardez à l’écart de tout matérielinflammable.

● Entfernen Sie brennbarres Material!

● Mantenha inflamáveis bem guarda-dos.

● Wear eye, ear and body protection.

● Protéjase los ojos, los oídos y elcuerpo.

● Protégez vos yeux, vos oreilles etvotre corps.

● Tragen Sie Augen-, Ohren- und Kör-perschutz!

● Use proteção para a vista, ouvido ecorpo.

WARNING

AVISO DEPRECAUCION

ATTENTION

WARNUNG

ATENÇÃO

Spanish

French

German

Portuguese

Japanese

Chinese

Korean

Arabic

LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA ASPRÁTICAS DE SEGURANÇA DO EMPREGADOR.

● Keep your head out of fumes.● Use ventilation or exhaust to

remove fumes from breathing zone.

● Los humos fuera de la zona de res-piración.

● Mantenga la cabeza fuera de loshumos. Utilice ventilación oaspiración para gases.

● Gardez la tête à l’écart des fumées.● Utilisez un ventilateur ou un aspira-

teur pour ôter les fumées des zonesde travail.

● Vermeiden Sie das Einatmen vonSchweibrauch!

● Sorgen Sie für gute Be- undEntlüftung des Arbeitsplatzes!

● Mantenha seu rosto da fumaça.● Use ventilação e exhaustão para

remover fumo da zona respiratória.

● Turn power off before servicing.

● Desconectar el cable de ali-mentación de poder de la máquinaantes de iniciar cualquier servicio.

● Débranchez le courant avant l’entre-tien.

● Strom vor Wartungsarbeitenabschalten! (Netzstrom völlig öff-nen; Maschine anhalten!)

● Não opere com as tampas removidas.● Desligue a corrente antes de fazer

serviço.● Não toque as partes elétricas nuas.

● Do not operate with panel open orguards off.

● No operar con panel abierto oguardas quitadas.

● N’opérez pas avec les panneauxouverts ou avec les dispositifs deprotection enlevés.

● Anlage nie ohne Schutzgehäuseoder Innenschutzverkleidung inBetrieb setzen!

● Mantenha-se afastado das partesmoventes.

● Não opere com os paineis abertosou guardas removidas.

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

im10044 vantage 575cummins - welding equipment rental · special precautions should be used to...

Documents