ic-f34 series
DESCRIPTION
ICOM radio communicationsTRANSCRIPT
ICIC--F34G/ICF34G/IC--F44G SeriesF44G SeriesSales HandbookSales Handbook
Version 1.1
August 2007
Europe Edition
FOREWORD and DISCLAIMER
The information in this document has been carefully checked, and is believed to be correct and accurate.
However, Icom assumes no responsibility for inaccuracies or mistakes. Furthermore, Icom reserves the
right to make changes to any of the products described in this handbook without notice or obligation. The
systems and applications described herein are for information and reference purposes only.
Handbook RevisionsHandbook RevisionsHandbook RevisionsHandbook Revisions
Icom reserves the right to make changes to the content of this handbook at any time without notice or
obligation.
IPR and CopyrightsIPR and CopyrightsIPR and CopyrightsIPR and Copyrights
The Icom products described in this handbook may include Icom Intellectual Property Rights (IPR) and/or
copyrighted Icom computer programs stored in radio memories or other media/devices. Such IPR and
Foreword
Disclaimer
This handbook is prepared to provide detailed information about the IC-F34G and IC-F44G series VHF and
UHF TRANSCEIVERS and UHF TRUNKED RADIOS.
2
copyrighted Icom computer programs stored in radio memories or other media/devices. Such IPR and
copyrighted computer programs are protected by laws in Japan, the United States and other countries.
Any Icom IPR and/or copyrighted Icom computer programs contained in the Icom products described in
this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any way.
Furthermore, the purchase of Icom products shall not be deemed to grant any license either directly or by
implication, except for the normal non-exclusive license to use the product that is specified by law in the
sale of a product.
Document CopyrightsDocument CopyrightsDocument CopyrightsDocument Copyrights
No duplication or distribution of this document or any portion thereof shall take place without the express
permission of Icom. Reproduction, distribution, or transmission for any purpose in any form or by any
means, electronic or mechanical, shall only be allowed with the express permission of Icom.
TrademarksTrademarksTrademarksTrademarks
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in the United
States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
All other products or brands are registered trademarks or trademarks of their respective holders.
© 2007 Icom Inc.
Table Of Contents
1 Introduction
1-1 Company Profile · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4
2 IC-F34G/IC-F44G Series (Overview)
2-1 Product Line Up · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5
2-2 Common Features · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 6
2-3 Key Features of BIIS 1200 Signalling · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 7
2-4 Function and Specifications Comparison · · · · · · · · · · · ·· ·· · · · · · · · · · · · · · 8
2-5 Supplied Accessories Attachments · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 9
2-6 Optional Accessories · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10-12
2-7 Battery Charging · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 13
2-8 Battery Charging and Battery Case · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 14
2-9 Optional Swivel Belt Clip · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 15
3 IC-F34G/IC-F44G Series (Operation and Function)
3-1 Operation and Function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 16
3-1-1 Function Display · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 17
3-1-2 Functions Programmable to Keys · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 18-20
Table Of Contents
3-1-2 Functions Programmable to Keys · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 18-20
3-2 Cloning Software CS-F33G
3-2-1 Basic Setup of Cloning Software · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 21-23
3-2-2 Cloning Items for Conventional Mode · · · · · · · · · · · · · · · · · · · · · · · · 24
3-2-3 Cloning Items for BIIS 1200 Functions · · · · · · · · · · · · · · · · · · · · · · · 25-29
3-3 2-Tone (LMR) Signalling · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 30
3-4 5-Tone (PMR) Signalling · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 31-32
3-5 Scan (Conventional Mode) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 33-37
3-6 Voice Scrambling Systems · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 38-39
4 IC-F44G Series (MPT Trunking Model)
4-1 Key Features · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 40
4-2 Operation and Function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 41
4-2-1 Function Display · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 42
4-2-2 Displaying Messages ·· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 43
4-3 Cloning Software CS-F44G (MPT) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 44-46
Appendix
A-1 Promotional Materials · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 47
A-2 Instruction Manual and Other Materials · · · · · · · · · · · · · · · · · · · · · · · · · 48
3
1 Introduction
1-1 Company Profile
Company ProfileCompany ProfileCompany ProfileCompany ProfileCompany ProfileCompany ProfileCompany ProfileCompany Profile
Icom, the wireless communication expertsIcom, the wireless communication expertsIcom, the wireless communication expertsIcom, the wireless communication expertsIcom Inc. is a company located in Osaka, Japan, and is a manufacturer of
wireless communication products. Since Icom’s establishment in 1954, we have
had a long record as a trusted manufacturer of land mobile radio, amateur radio,
marine radio, navigation products, aviation radio and communications receivers.
Quality & ReliabilityQuality & ReliabilityQuality & ReliabilityQuality & ReliabilityQuality & ReliabilityQuality & ReliabilityQuality & ReliabilityQuality & Reliability
Icom quality and Icom reliabilityIcom quality and Icom reliabilityIcom quality and Icom reliabilityIcom quality and Icom reliabilityOver 50 years of engineering and production excellence is a part of every Icom
product. Using the latest equipment, Icom radios are tested to pass rigorous in-
house tests as well as environmental tests to the US Military standard 810
specifications. Icom Inc holds ISO9001:2000 certification.
ProductionProductionProductionProductionProductionProductionProductionProduction
Made in Japan qualityMade in Japan qualityMade in Japan qualityMade in Japan qualityIcom is a rare example of an electronics manufacturer that has not shifted
production to lower cost countries, but kept its production base 100% in Japan.
4
production to lower cost countries, but kept its production base 100% in Japan.
The Wakayama Icom plant has an advanced production system to produce small
volume/multi-model wireless communication products.
Icom brandIcom brandIcom brandIcom brandIcom brandIcom brandIcom brandIcom brand
Icom, world brand nameIcom, world brand nameIcom, world brand nameIcom, world brand nameIcom is today recognized as a reliable 2-way radio brand name around the world.
Our land mobile radios are used by many professional organizations all over the
world, like the United States Department of Defense and the U.S. Marine Corps.
who chose Icom as the first Japanese company to supply radios to them.
NetworkNetworkNetworkNetwork
Icom's worldwide networkIcom's worldwide networkIcom's worldwide networkIcom's worldwide networkIcom’s products are sold in over 80 countries in the World. Icom has an
international sales and service network around the world, including sales
subsidiaries in the US, Australia, Germany, Spain and liaison offices in France
and China. Icom is here to support and service our products and your
communication needs.
2-1 IC-F34G/IC-F44G Series Models
VHF Handheld TransceiversVHF Handheld TransceiversVHF Handheld TransceiversVHF Handheld Transceivers
UHF Handheld TransceiversUHF Handheld TransceiversUHF Handheld TransceiversUHF Handheld Transceivers
UHF Trunked RadiosUHF Trunked RadiosUHF Trunked RadiosUHF Trunked Radios
MTP 1327 Version MTP 1327 Version MTP 1327 Version MTP 1327 Version
5
S series(Simple keypad version)
T series(10-keypad version)
Standard MIL 810C MIL 810D MIL 810E MIL 810F
Method Proc. Method Proc. Method Proc. Method Proc.
Low Pressure 500.1 I 500.2 I, II 500.3 I, II 500.4 I, II
High Temp. 501.1 I 501.2 I, II 501.3 I, II 501.4 I, II
Low Temp. 502.1 I 502.2 I, II 502.3 I, II 502.4-3 I, II
Temp. Shock 503.1 I 503.2 I 503.3 I 503.4 I
Solar Radiation 505.1 I 505.2 I 505.3 I 505.4 I
Rain Blowing/Drip 506.1 I, II 506.2 I, II 506.3 I, II 506.4 I, III
Humidity 507.1 I, II 507.2 II, III 507.3 II, III 507.4 –
Salt Fog 509.1 I 509.2 I 509.3 I 509.4 –
Dust Blowing 510.1 I 510.2 I 510.3 I 510.4 I
Vibration 514.2 VIII, X 514.3 I 514.4 I 514.5 I
Shock 516.2 I, II, V 516.3 I, IV 516.4 I, IV 516.5 I, IV
The aluminum dieThe aluminum dieThe aluminum dieThe aluminum die----cast chassis and polycarbonate casing combination cast chassis and polycarbonate casing combination cast chassis and polycarbonate casing combination cast chassis and polycarbonate casing combination
have been tested to MIL standard specifications.have been tested to MIL standard specifications.have been tested to MIL standard specifications.have been tested to MIL standard specifications.
The MILMILMILMIL----STDSTDSTDSTD----810810810810 series of standards are issued by the United States Army's
Developmental Test Command, to specify various environmental tests to
prove that equipment qualified to the standard will survive in the field
Icom Icom Icom Icom makes rugged products that have been tested to and passed the
following MIL-STD requirements and strict environmental standards.
2-2 Common Features
LithiumLithiumLithiumLithium----Ion battery packIon battery packIon battery packIon battery pack
The battery is a lightweight yet high capacity 2000mAh
Li-Ion unit. Li-Ion technology has virtually no memory
charging issues. A rugged dual-rail guide securely locks
the battery to the radio. Optional battery case BP-240
provides a convenient back up and great reassurance in
emergency.
Wide frequency range and large channel capacityWide frequency range and large channel capacityWide frequency range and large channel capacityWide frequency range and large channel capacity
The IC-F34G series covers a wide frequency range in
one version (VHF 136–174 MHz, UHF 400–470MHz ).
The 256 memory channel capacity with 16 memory
banks allows you to divide and store a variety of flexible
channel groupings. Easy memory channel selection with
Advanced functions packed in a tough, lightweight body
8 programmable buttons8 programmable buttons8 programmable buttons8 programmable buttons
The [P0]–[P3], [], [], [Red] and [Monitor] buttons are
programmable to meet specific needs. The [Red] button
on the top panel can be assigned as an emergency
trigger.
Alphanumeric displayAlphanumeric displayAlphanumeric displayAlphanumeric display
The 8-character alphanumeric display shows channel,
bank, tone code and scanning channel names on the
display. A separate row of operational icons indicate
battery, signal strength, RX/TX and other radio
conditions.
Audio companderAudio companderAudio companderAudio compander
The IC-F34G series is suitable for a variety of needs — large or small, mobile or stationary.
Whether you are a large-scale construction site, warehouse, hospital or hotel, or a small on the
go messenger service, this radio provides the built-in flexibility to handle your communication
needs. A reliable 2-way communications tool. This is the new direction in LMR/PMR
communications. Below are some of the common features of this series.
channel groupings. Easy memory channel selection with
a simple rotation of the rotary channel knob.
Small and lightweight bodySmall and lightweight bodySmall and lightweight bodySmall and lightweight body
The IC-F34G series sheds size and weight compared
with previous models, weighing just 340g (including BP-
232N) and measuring only 53(W)×120(H)×36.9(D)
mm. The aluminum die-cast chassis and polycarbonate
casing combination have been tested to MIL standard
specifications.
BuiltBuiltBuiltBuilt----in multiin multiin multiin multi----format tone signallingformat tone signallingformat tone signallingformat tone signalling
Use the built-in CTCSS, DTCS, 2-Tone, 5-Tone or BIIS
capability to set up your own talk groups and quiet
stand-by when others are talking. You can also set up
selective calls to individuals or control a repeater.
Multiple 2Multiple 2Multiple 2Multiple 2----Tone, Multiple 5Tone, Multiple 5Tone, Multiple 5Tone, Multiple 5----ToneToneToneTone
Encode or decode up to 10 2-Tone, 8 5-Tone codes on a
single memory channel. This is perfect for professionals
who require multiple district paging on one channel.
When a matched tone is received, the following items
are programmable for each code.
• Bell icon
• Answer back
• Stun
• Beep sound
• Auto transmit
• Scan
6
Audio companderAudio companderAudio companderAudio compander
The built-in audio compander reduces noise
components and provides clear reception even in
narrow band use.
BuiltBuiltBuiltBuilt----in voice scramblerin voice scramblerin voice scramblerin voice scrambler
The IC-F34G series includes a built-in inversion type
voice scrambler in all models. When a more secure
system is required, the optional voice scrambler unit UT-
109 or UT-110 is available.
Other featuresOther featuresOther featuresOther features
• 8 DTMF autodial memories
• 2 step reduced power setting
• Power on password
• Busy, repeater lockout functions
•Programmable wide and narrow channel bandwidth
(25/12.5kHz or 20/12.5kHz) and more...
2-3 Key Features of BIIS 1200 Signalling
What is BIIS 1200?What is BIIS 1200?What is BIIS 1200?What is BIIS 1200?
BIIS 1200 (Binary Interchange of Information and
Signalling ) is a signalling protocol standardized by
ETSI (European Telecommunications Standards
Institute). The protocol allows users to send and
receive short status messages as well as messaging
updates.
The 1200 in the BIIS 1200 name signifies that data is
transmitted at the high speed rate of 1200 bits per
second (Baud) MSK modulation.
Key FeaturesKey FeaturesKey FeaturesKey FeaturesCompatible with conventional radiosCompatible with conventional radiosCompatible with conventional radiosCompatible with conventional radios
The BIIS radios are fully compatible with the
conventional version of other Icom models.
Conventional channels and BIIS channels are
programmable in the same radio and can be selected
on site.
Transport, logistics, utilities, public safety... Those professional mobile
users require efficient but cost effective systems for managing their
organization. The BIIS 1200 standard is the best choice to add a data
service to an existing system. The BIIS system provides AVL, text and
status message services as well as voice communication.
BIIS 1200
Compatible
BIIS 1200
Compatible
Short Data MessageShort Data MessageShort Data MessageShort Data Message
A max 95-character SDM can be sent and received with
the radio. The DTMF keypad allows you to input a max.
12-character message directly from the keypad.
Digital ANIDigital ANIDigital ANIDigital ANI
BIIS 1200
I know who is calling
24242424----status messagesstatus messagesstatus messagesstatus messages
Status messages are simplified SDM’s. Choose a
message from 24 pre-programmed status messages
and send it. Certain status messages can be
programmed to be sent with power on/off.
32 call memories32 call memories32 call memories32 call memories
The radio shows the callers name on the display when
receiving a call. You can also make a call by selecting a
name from the memory list or inputting the
abbreviated number.
7
GPS TrackingGPS TrackingGPS TrackingGPS Tracking
The optional RS-232C interface cable provides a GPS
receiver, PC or Printer connection. When connected to a
GPS receiver, position information can be sent with PTT
button or at preprogrammed intervals. If a base station
is connected to a PC with mapping software, a vehicle
management system can allow you to manage a vehicle
fleet efficiently.
Your own digital ID can be sent with a log in and/or log
off message to the network. Up to 7 group IDs allow
group calls.
BIIS 1200
Compatible
BIIS 1200
Compatible
BIIS 1200
CompatibleBIIS 1200
Compatible
Killer IDKiller IDKiller IDKiller ID
When receiving a call with a Killer ID, use of the radio is
inhibited until the correct pass code is entered.
2-4 Function and Specifications Comparison
IC-F34G/IC-F44G Series Transceivers
MODEL NO. IC-F34GT IC-F44GT IC-F44GT
VERSION #03 #35 #15
DESTINATIONS EUR-01 EUR-01 MTE-01
Keypad Type 10 Key Type 10 Key Type 10 Key Type
MODEL NO. IC-F34GS IC-F44GS IC-F44GS
VERSION #53 #85 #65
DESTINATIONS EUR-01 EUR-01 MTE-01
Keypad Type Simple type Simple type Simple type
TYPE APPROVAL R&TTE R&TTE R&TTE
SUPPLIED ANTENNA FA-SC55V FA-SC57U FA-SC57U
FUNCTION COMPARISON
CTCSS
DTCS
2-Tone 5-Tone
DTMF autodial
DTMF decoder *1 *1
BIIS 1200
MDC 1200
MPT 1327
LTR™ trunking
PassPort
Intrinsically safe
SPECIFICATIONS
GENERAL
Frequency Range (MHz) 136 ~ 174 400 ~ 470 400 ~ 470
Number of channels 256 ch/16 banks 256 ch/16 zones 32 (conventional)Channel Spacing (kHz) 12.5/20/25 12.5/20/25 12.5/20/25
PLL channel step (Unit: kHz) 2.5, 3.125 5, 6.25 5, 6.25
Current drain
Tx High 1.5A 1.7A 1.7A
RxStand-by 85mA 85mA 85mA
8
GENERAL
Current drainRx
Stand-by 85mA 85mA 85mA
Max. audio 300mA 300mA 300mA
Operating Time with BP-232N 16 hours*2 15 hours*2 13 hours*2
Dimensions (W×H×D)
(projections not included)53×120×36.9 mm 53×120×36.9 mm 53×120×36.9 mm
Weight (approx.) 340g (with BP-232N) 340g (with BP-232N) 340g (with BP-232N)
TX
RF output power (High) 5W 4W 4W
Spurious emissions 0.25µW (≤1GHz) 0.25µW (≤1GHz) 0.25µW (≤1GHz)
Adjacent channel power (W/M/N) 70/70/60dB (min) 70/70/60dB (min.) 70/70/60dB (min.)
RX
Sensitivity at 20dB SINAD (emf) –4dBµV (typ.) –4dBµV (typ.) –4dBµV (typ.)
Adjacent channel selectivity (W/M/N) 75/75/65dB (typ.) 73/73/63dB (typ.) 73/73/63dB (typ.)
Spurious response rejection 70dB 70dB 70dB
Intermodulation rejection 67dB (typ.) 67dB (typ.) 67dB (typ.)
AF output power
(at 5% distortion with an 8Ω load)500mW (typ.) 500mW (typ.) 500mW (typ.)
*1 Provide DTMF, selective call and ANI capability with optional UT-108 unit
*2 Operating time is approximate time (at 20°C). Tx: Rx: standby=5:5:90. Power save on.
Simple keypad
version
10-keypad
version
VHF Antenna
Battery Pack
BP-232N
Belt Clip
MB-94
Unit
cover
Jack cover
Supplied Accessories(May differ according to version)
UHF Antenna
2-5 Supplied Accessory Attachments
Flexible antennaFlexible antennaFlexible antennaFlexible antennaConnect the supplied flexible antenna to the antenna
connector.
Battery packBattery packBattery packBattery packTo attach the battery pack:To attach the battery pack:To attach the battery pack:To attach the battery pack:
Slide the battery pack in the direction of the arrow (①), then
lock it with the battery release button.
• Slide the battery pack until the battery release button
makes a ‘click’ sound.
To release the battery pack:To release the battery pack:To release the battery pack:To release the battery pack:
Push the battery release button in the direction of the arrow
(②) as shown below. The battery pack is then released.
CAUTION!CAUTION!CAUTION!CAUTION!
• NEVER HOLD NEVER HOLD NEVER HOLD NEVER HOLD by the antenna when carrying the transceiver.
• Transmitting without an antenna may damage the transceiver.
NEVER NEVER NEVER NEVER release or attach the battery pack when the transceiver is wet or
soiled. This may result water or dust getting into the transceiver/battery
Attach the supplied accessories as shown below.
9
soiled. This may result water or dust getting into the transceiver/battery
pack and may result in the transceiver being damaged.
Belt clipBelt clipBelt clipBelt clipTo attach the belt clip:To attach the belt clip:To attach the belt clip:To attach the belt clip:
1. Release the battery pack if it is attached.
2. Slide the belt clip in the direction of the arrow until the
belt clip is locked and makes a ‘click’ sound.
To detach the belt clip:To detach the belt clip:To detach the belt clip:To detach the belt clip:
1. Release the battery pack if it is attached.
2. Lift the clip (①), and slide the belt clip in the direction of
the arrow (②).
Jack coverJack coverJack coverJack coverAttach the jack cover when the optional speaker-microphone
is not used.
To attach the jack cover:To attach the jack cover:To attach the jack cover:To attach the jack cover:
1. Attach the jack cover on the [SP MIC] connector.[SP MIC] connector.[SP MIC] connector.[SP MIC] connector.
2. Tighten the screws.
To detach the jack cover:To detach the jack cover:To detach the jack cover:To detach the jack cover:
1. Unscrew the screw with a Phillips screwdriver.
2. Detach the jack cover for the speaker-microphone
connection.
2-6 Optional Accessories
BPBPBPBP----230N230N230N230N
Li-Ion 7.4V/ 980mAh
BPBPBPBP----232N232N232N232N
Li-Ion 7.4V/ 2000mAh AAA(LR03) batteries×6
BPBPBPBP----240240240240
REGULAR CHARGERREGULAR CHARGERREGULAR CHARGERREGULAR CHARGER RAPID CHARGERRAPID CHARGERRAPID CHARGERRAPID CHARGER RAPID CHARGERRAPID CHARGERRAPID CHARGERRAPID CHARGER
ADADADAD----106 106 106 106
BATTERY PACKS and CASEBATTERY PACKS and CASEBATTERY PACKS and CASEBATTERY PACKS and CASE
Current options available are shown below. Ask your Icom distributor for further details if required.
(*Not available for all countries.)
10
BCBCBCBC----121N 121N 121N 121N MULTI-CHARGER + ADADADAD----106 106 106 106 CHARGER ADAPTER
+ BCBCBCBC----157 157 157 157 AC ADAPTER
Rapidly charges up to 6 battery packs (Six AD-106s are required).
Charging time: approx.3 hours when BP-232N is attached.
OPCOPCOPCOPC----656 656 656 656 DC POWER CABLE :For use with the BC-121N. (12–20V
DC required).
BCBCBCBC----171 171 171 171 DESKTOP CHARGER
+ BCBCBCBC----147 147 147 147 AC ADAPTER
Charges the battery pack in
10 hours (approx.).
BCBCBCBC----160 160 160 160 DESKTOP CHARGER
+ BCBCBCBC----145 145 145 145 AC ADAPTER
Charges the BP-232N in 3
hours (approx.).
BCBCBCBC----119N 119N 119N 119N DESKTOP CHARGER
+ ADADADAD----106 106 106 106 CHARGER ADAPTER
+ BCBCBCBC----145 145 145 145 AC ADAPTER
Charges the BP-232N in 3
hours (approx.).
BCBCBCBC----147147147147 BCBCBCBC----171171171171 BCBCBCBC----160160160160 BCBCBCBC----145145145145
ADADADAD----106 (6 pcs).106 (6 pcs).106 (6 pcs).106 (6 pcs). BCBCBCBC----121N121N121N121N
MULTIMULTIMULTIMULTI----CHARGERCHARGERCHARGERCHARGER
BCBCBCBC----157157157157
OPCOPCOPCOPC----656656656656
BCBCBCBC----145145145145 BCBCBCBC----119N119N119N119N
POWER SUPPLY CABLESPOWER SUPPLY CABLESPOWER SUPPLY CABLESPOWER SUPPLY CABLES
CPCPCPCP----17L 17L 17L 17L OPCOPCOPCOPC----515L515L515L515L
CPCPCPCP----17L 17L 17L 17L CIGARETTE LIGHTER CABLE,
OPCOPCOPCOPC----515L 515L 515L 515L DC POWER CABLE
For use with the BC-160 or BC-119N.
(12–16V DC required).
Optional Accessories
BELT CLIPSBELT CLIPSBELT CLIPSBELT CLIPS LEATHER BELT HANGERSLEATHER BELT HANGERSLEATHER BELT HANGERSLEATHER BELT HANGERS
MBMBMBMB----93 : 93 : 93 : 93 : Swivel type MBMBMBMB----94 : 94 : 94 : 94 : Alligator
type Same as
supplied.
MBMBMBMB----96N :96N :96N :96N : Swivel
type. MB-93 swivel
joints supplied
MBMBMBMB----96F : 96F : 96F : 96F : Fixed type
HEADSETS and PTT/VOX UNITHEADSETS and PTT/VOX UNITHEADSETS and PTT/VOX UNITHEADSETS and PTT/VOX UNIT
SPSPSPSP----13 13 13 13 : EARPHONE
Provides clear audio in
noisy environments.
EARPHONEEARPHONEEARPHONEEARPHONE
11
Swivel type.
MB-86 and MB-93
swivel joints supplied
HSHSHSHS----94 : 94 : 94 : 94 : Earhook headset
with flexible boom
microphone.
VSVSVSVS----1L 1L 1L 1L : PTT/VOX unit.
Required when using
these headsets with the
transceiver
HSHSHSHS----97 : 97 : 97 : 97 : Throat
microphone fits around
the neck and picks up
speech vibration.
HSHSHSHS----95 95 95 95 : Behind-the-head
headset with flexible
boom microphone.
HMHMHMHM----153L 153L 153L 153L : Durable
earphone-microphone
with revolving clip.
HMHMHMHM----158L 158L 158L 158L : Compact and
durable body with
screw-type connector.
HMHMHMHM----159L 159L 159L 159L : Full size
durable speaker
microphone.
SPEAKERSPEAKERSPEAKERSPEAKER----MICROPHONESMICROPHONESMICROPHONESMICROPHONES
HMHMHMHM----166L 166L 166L 166L : Earphone
microphones
Optional Accessories
*INTERNAL UNITS*INTERNAL UNITS*INTERNAL UNITS*INTERNAL UNITS
FAFAFAFA----SC56VS SC56VS SC56VS SC56VS : 150–162MHz, Red
FAFAFAFA----SC57VS SC57VS SC57VS SC57VS : 160–174MHz, Green
FAFAFAFA----SC73US SC73US SC73US SC73US : 450–490MHz, Red
FAFAFAFA----SC61VC SC61VC SC61VC SC61VC : 136–174MHz, White
FAFAFAFA----SC61UC SC61UC SC61UC SC61UC : 380–520MHz, White
FAFAFAFA----SC25V SC25V SC25V SC25V : 136–150MHz, Blue
FAFAFAFA----SC55V SC55V SC55V SC55V : 150–174MHz, Red
FAFAFAFA----SC25U SC25U SC25U SC25U : 400–430MHz, Green
FAFAFAFA----SC57U SC57U SC57U SC57U : 430–470MHz, Red
FAFAFAFA----SC72U SC72U SC72U SC72U : 470–520MHz, Blue
STUBBY ANTENNASSTUBBY ANTENNASSTUBBY ANTENNASSTUBBY ANTENNASANTENNASANTENNASANTENNASANTENNAS CUT ANTENNASCUT ANTENNASCUT ANTENNASCUT ANTENNAS
12
Swivel type.
MB-93
swivel joints
supplied
*INTERNAL UNITS*INTERNAL UNITS*INTERNAL UNITS*INTERNAL UNITS
UTUTUTUT----108 108 108 108 DTMF DECODER :
Provides DTMF, Selective call
and ANI capabilities
NOT AVAILABLE NOT AVAILABLE NOT AVAILABLE NOT AVAILABLE for MT version
UTUTUTUT----110 110 110 110 VOICE SCRAMBLER
UNIT : : : : Up to 1020 scrambling
codes are available. Version 02
is required.
UTUTUTUT----124 124 124 124 MAN DOWN UNIT :
Automatically sends an
emergency signal when the
transceiver is left in a
horizontal
NOT AVAILABLE NOT AVAILABLE NOT AVAILABLE NOT AVAILABLE for MT
version
UTUTUTUT----109 109 109 109 VOICE SCRAMBLER
UNIT : Up to 32 scrambling
codes are available. Version 02
is required.
CLONING SOFTWARECLONING SOFTWARECLONING SOFTWARECLONING SOFTWARE
CSCSCSCS----F33G F33G F33G F33G : for the IC-F34GT/GS, IC-
F44GT/GS VHF/UHF TRANSCEIVERS
CSCSCSCS----F44G(MPT) F44G(MPT) F44G(MPT) F44G(MPT) : for the IC-
F44GT/GS UHF TRUNKED RADIOS
OPCOPCOPCOPC----478 478 478 478 : RS-232C type CLONING
CABLE
OPCOPCOPCOPC----478UC 478UC 478UC 478UC : USB type CLONING
CABLE
*Refer to the “OPTION UNIT INSTALLATION” section of the Instruction Manual for installation of INTERNAL UNITs.
2-7 Battery Charging
Using the optional battery chargersUsing the optional battery chargersUsing the optional battery chargersUsing the optional battery chargers
Rapid charging with the BCRapid charging with the BCRapid charging with the BCRapid charging with the BC----160160160160
The optional BC-160 provides rapid charging of optional
Li-Ion battery packs.
• An AC adapter (may be supplied with BC-160
depending on version) or the DC power cable (OPC-
515L/CP-17L) is additionally required.
Screws
supplied with
the charger
adapter
AD-106
Connectors
Plugs
AC adapter (Not supplied
with some versions.)
Optional OPC-515L
(for 13.8 V power
source) or CP-17L
(for 12 V cigarette
lighter socket) can
be used instead of
the AC adapter.
BATTERY BATTERY BATTERY BATTERY
PACKPACKPACKPACKTRANSCEIVERTRANSCEIVERTRANSCEIVERTRANSCEIVER
ADADADAD----106 installation106 installation106 installation106 installation
① Install the AD-106 desktop charger adapter into the
holder space of the BC-119N/BC-121N.
② Connect the plugs of the BC-119N/BC-121N to the
AD-106 desktop charger adapter with the connector,
then install the adapter into the charger with the
supplied screws.
The charging instructions below are shown here for your reference.
13
the AC adapter.
Rapid charging with the BCRapid charging with the BCRapid charging with the BCRapid charging with the BC----119N+AD119N+AD119N+AD119N+AD----106106106106
The optional BC-119N provides rapid charging of battery
packs. The following items are additionally required.
• AD-106 charger adapter
• An AC adapter (may be supplied with BC-119N
depending on version) or the DC power cable (OPC-
515L/CP-17L).
TRANSCEIVERTRANSCEIVERTRANSCEIVERTRANSCEIVER
BATTERYBATTERYBATTERYBATTERY
PACKPACKPACKPACK
AD-106 charger
adapter is installed
in BC-119N.
AC adapter
(Not supplied with
some versions.)
Optional OPC-515L (for 13.8
V power source) or CP-17L
(for 12 V cigarette lighter
socket) can be used instead
of the AC adapter.
Rapid charging with the BCRapid charging with the BCRapid charging with the BCRapid charging with the BC----121N+AD121N+AD121N+AD121N+AD----106106106106
The optional BC-121N allows up to 6 battery packs to be
charged simultaneously. The following items are
additionally required.
• Six AD-106 charger adapters
• An AC adapter (BC-157) or the DC power cable (OPC-
656)
AD-106 charger
adapters are
installed
in each slot.
TRANSCEIVERTRANSCEIVERTRANSCEIVERTRANSCEIVER
BATTERYBATTERYBATTERYBATTERY
PACKPACKPACKPACK
AC adapter
(Purchased
Separately)
DC power cable (OPC-656)
(Connect with the DC power supply;
13.8 V/at least 7 A)
2-8 Battery Charging and Battery Case
IMPORTANT!: Battery chargingIMPORTANT!: Battery chargingIMPORTANT!: Battery chargingIMPORTANT!: Battery chargingEnsure the guide lobs on the battery pack are correctly
aligned with the guide rails inside the charger adapter.
(This illustration is described with the BC-160.)
Lobs
Guide rail
Optional battery case (BPOptional battery case (BPOptional battery case (BPOptional battery case (BP----240)240)240)240)When using the optional battery case, install 6 × AAA
(LR03) size alkaline batteries as illustrated at right.
① Unhook the battery cover release hook (), and
open the cover in the direction of the arrow (.
(Fig.1)
② Then, install 6 × AAA (LR03) size alkaline batteries.
(Fig.2)
• Install the alkaline batteries only.
• Be sure to observe the correct polarity.
• Do not pin the ribbon under the batteries.
③ Fit the cover in the direction of the arrow (), then
close (). And hook the battery cover release hook
until it makes a ‘click’ sound (). (Fig.3)
CAUTION:CAUTION:CAUTION:CAUTION:• When installing batteries, make sure they are all the same brand, type and capacity. Also, do not mix new
and old batteries together.
• Keep battery contacts clean. It’s a good idea to clean battery terminals once a week.
• Never incinerate used battery cells since internal battery gas may cause them to rupture.
Battery cautionBattery cautionBattery cautionBattery caution
DANGER DANGER DANGER DANGER Charge the specified Icom batteries only. Only
14
battery gas may cause them to rupture.
• Never expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before
using it.
Fig.3Fig.3Fig.3Fig.3
Fig.2Fig.2Fig.2Fig.2
Fig.1Fig.1Fig.1Fig.1BPBPBPBP----240240240240
DANGER DANGER DANGER DANGER Charge the specified Icom batteries only. Only
tested and approved for use with genuine Icom
batteries. Fire and/or explosion may occur when a third
party battery pack or counterfeit product is charged.
CAUTION! NEVER CAUTION! NEVER CAUTION! NEVER CAUTION! NEVER insert battery pack/transceiver (with
the battery pack attached) in a wet or soiled condition
into the charger. This may result in corrosion of the
charger terminals or damage to the charger. The charger
is not waterproof and water can easily get into it.
NEVER NEVER NEVER NEVER incinerate used battery packs. Internal battery
gas may cause an explosion.
NEVER NEVER NEVER NEVER immerse the battery pack in water. If the battery
pack becomes wet, be sure to wipe it dry BEFORE
attaching it to the transceiver.
NEVER NEVER NEVER NEVER short the terminals of the battery pack. Also,
current may flow into nearby metal objects, such as a
necklace, etc. Therefore, be careful when carrying with,
or placing near metal objects, carrying in handbags, etc.
AVOID AVOID AVOID AVOID leaving the battery pack in a fully charged, or
completely discharged condition for long time. It causes
shorter battery life. In case of leaving the battery pack
unused for a long time, it must be kept safely after
discharge, or use the battery until the battery indicator
appears, then remove it from the transceiver. If your
battery pack seems to have no capacity even after being
charged, fully charge the battery pack again.
If the batteries still do not retain a charge (or very little),
new battery pack must be purchased.
2-9 Optional Swivel Belt Clip
To attachTo attachTo attachTo attach
① Release the battery pack if it is attached.
② Slide the base clip in the direction of the arrow until
the base clip is locked and makes a ‘click’ sound.
SWIVEL BELT CLIPSWIVEL BELT CLIPSWIVEL BELT CLIPSWIVEL BELT CLIP
MBMBMBMB----93 contents93 contents93 contents93 contents
Qty.
① Belt clip……………………………………………………… 1
② Base clip …………………………………………………… 1
② Release the battery pack if it is attached.
③ Pinch the clip (), and slide the base clip in the
direction of the arrow ().
To detachTo detachTo detachTo detach
① Turn the transceiver upside down in the direction of
the arrow and pull out from the belt clip.
15
④ Once the transceiver is locked in place, it swivels as
illustrated below.
③ Clip the belt clip to a part of your belt. And insert the
transceiver into the belt clip until the base clip
inserted fully into the groove.
CAUTION!CAUTION!CAUTION!CAUTION!HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR
DETACHING THE TRANSCEIVER FROM THE BELT CLIP.DETACHING THE TRANSCEIVER FROM THE BELT CLIP.DETACHING THE TRANSCEIVER FROM THE BELT CLIP.DETACHING THE TRANSCEIVER FROM THE BELT CLIP.
Otherwise the transceiver may not be attached to the
holder or swivel properly if the transceiver is accidentally
dropped and the base clip is scratched or damaged.
3 IC-F34G/IC-F44G Series (Operation and Function)
3-1 Operation and Function
VOLUME CONTROL [VOL]VOLUME CONTROL [VOL]VOLUME CONTROL [VOL]VOLUME CONTROL [VOL]
Rotate to turn the power
ON/OFF and adjusts the
audio level.
ANTENNA CONNECTORANTENNA CONNECTORANTENNA CONNECTORANTENNA CONNECTOR
Connects the supplied
antenna.
DEALERDEALERDEALERDEALER----PROGRAMMABLE PROGRAMMABLE PROGRAMMABLE PROGRAMMABLE
KEY [RED]KEY [RED]KEY [RED]KEY [RED]
Desired function can be
programmed by your dealer.
ROTARY SELECTORROTARY SELECTORROTARY SELECTORROTARY SELECTOR
Rotate to select the pre-
programmed memory
channels or the operating
bank. (Depending on the
pre-setting)
MONITOR KEYMONITOR KEYMONITOR KEYMONITOR KEY
Mute and release the CTCSS
(DTCS) or 2-tone squelch mute.
Open any squelch/deactivate any
mute while pushing this key. (LMR
operation only)
Activates one of (or two of) the
following functions on each
channel independently. (PMR or
BIIS PMR operation only)
• Push and hold the key to
unmute the channel (audio is
emitted; ‘audible’ condition).
• Push the key to toggle the mute
and unmute conditions (toggles
‘audible’ and ‘inaudible’).
• Push the key to mute the
channel (sets to ‘inaudible’ only).
• Push the key to unmute the
channel (sets to ‘audible’ only).
• Push the key after
communication is finished to
send a ‘reset code.’
• Push the key after
Note: Operation of the functions described below may depend on radio programming.
16
[SP]/[MIC] JACK[SP]/[MIC] JACK[SP]/[MIC] JACK[SP]/[MIC] JACK
Connect the optional
speaker-microphone.
DEALERDEALERDEALERDEALER----PROGRAMMABLE PROGRAMMABLE PROGRAMMABLE PROGRAMMABLE
KEYS [P0] to [P3]KEYS [P0] to [P3]KEYS [P0] to [P3]KEYS [P0] to [P3]
Desired functions can be
programmed independently
by your dealer.
FUNCTION DISPLAYFUNCTION DISPLAYFUNCTION DISPLAYFUNCTION DISPLAY
Displays a variety of
information such as an
operating channel
number/name, 2/5-tone
code, DTMF numbers,
selected function, etc.
10101010----KEYPAD (Depending on version)KEYPAD (Depending on version)KEYPAD (Depending on version)KEYPAD (Depending on version)
The keypad allows you to enter digits to:
• Select memory channels
• Select tone channels
• Select DTMF codes (during transmit)
• Set TX codes
• Set BIIS status number
• Input text message for SDM operation
• Start up with the password
UP/DOWN KEYSUP/DOWN KEYSUP/DOWN KEYSUP/DOWN KEYS
Push to select an operating channel.
Push to select a TX code channel after pushing [TX CODE CH
SELECT].
Push to select a DTMF channel after pushing [DTMF].
Push to select a scan group after pushing and holding [SCAN].
Push to select a BIIS code, status number or SDM after
pushing [DIGITAL].
*Desired functions can be programmed independently by your
dealer.
PTT SWITCH [PTT]PTT SWITCH [PTT]PTT SWITCH [PTT]PTT SWITCH [PTT]
Push and hold to transmit; release to receive.
Push to transmit the call during MSK operation, depending
on the setting.
• Push the key after
communication is finished to
send a ‘clear down code’ during
BIIS operation on an MSK
channel.
NOTE: NOTE: NOTE: NOTE: The unmute condition
(‘audible’ conditions) may
automatically return to the mute
condition (‘inaudible’ condition)
after a specified period.
*Desired function can be
programmed by your dealer.
3-1-1 Function Display
1.1.1.1. TRANSMIT INDICATORTRANSMIT INDICATORTRANSMIT INDICATORTRANSMIT INDICATOR
Appears while transmitting.
2.2.2.2. BUSY INDICATORBUSY INDICATORBUSY INDICATORBUSY INDICATOR
Appears while the channel is busy.
3.3.3.3. SCROLL INDICATORSCROLL INDICATORSCROLL INDICATORSCROLL INDICATOR
Appears when a received SDM including
more than 8 characters is displayed.
4.4.4.4. SIGNAL STRENGTH INDICATORSIGNAL STRENGTH INDICATORSIGNAL STRENGTH INDICATORSIGNAL STRENGTH INDICATOR
Indicates relative signal strength level.
11111111 KEY LOCK INDICATORKEY LOCK INDICATORKEY LOCK INDICATORKEY LOCK INDICATOR
Appears during the key lock function is
ON.
12121212 BATTERY INDICATORBATTERY INDICATORBATTERY INDICATORBATTERY INDICATOR
Appears or blinks when the battery
power decreases to a specified level.
13131313 ALPHANUMERIC DISPLAYALPHANUMERIC DISPLAYALPHANUMERIC DISPLAYALPHANUMERIC DISPLAY
Displays an operating channel number,
channel name, Set mode contents,
DTMF code, etc.
17
5.5.5.5. LOW POWER INDICATORLOW POWER INDICATORLOW POWER INDICATORLOW POWER INDICATOR
Appears when low output power is
selected.
• When the battery power decreases to a specified level, low power is selected
automatically.
6.6.6.6. AUDIBLE INDICATORAUDIBLE INDICATORAUDIBLE INDICATORAUDIBLE INDICATOR
Appears when the channel is in the
‘audible’ (unmute) condition.
Appears when the specified 2/5-
tone/BIIS code is received.
7.7.7.7. COMPANDER INDICATORCOMPANDER INDICATORCOMPANDER INDICATORCOMPANDER INDICATOR
• Appears when the compander function is activated.
8.8.8.8. SCRAMBLER INDICATORSCRAMBLER INDICATORSCRAMBLER INDICATORSCRAMBLER INDICATOR
Appears when the voice scrambler
function is activated.
9.9.9.9. BELL INDICATORBELL INDICATORBELL INDICATORBELL INDICATOR
Appears/blinks when the specific 2/5-
tone/BIIS code is received, according to
the pre-programming.
10.10.10.10. CALL CODE MEMORY INDICATORCALL CODE MEMORY INDICATORCALL CODE MEMORY INDICATORCALL CODE MEMORY INDICATOR
Appears when the call code memory is
selected.
DTMF code, etc.
Note: Appearance of icons on the LCD display depends on the function used and radio programming.
3-1-2 Functions Programmable to Keys
The following functions can be assigned to [UP], [DOWN], [UP], [DOWN], [UP], [DOWN], [UP], [DOWN],
[P0], [P1], [P2], [P3], [RED] and [MONITOR] [P0], [P1], [P2], [P3], [RED] and [MONITOR] [P0], [P1], [P2], [P3], [RED] and [MONITOR] [P0], [P1], [P2], [P3], [RED] and [MONITOR]
programmable programmable programmable programmable function keys.
Consult your Icom dealer or system operator for details
concerning your transceivers programming.
If the programmable function names are bracketed in
the following explanations, the specific key is used to
activate the function depends on the programming.
CH UP AND DOWN KEYSCH UP AND DOWN KEYSCH UP AND DOWN KEYSCH UP AND DOWN KEYS
Push to select an operating channel.
Push to select a transmit code channel after
pushing [TX Code CH Select].
Push to select a DTMF channel after pushing
[DTMF Autodial].
Push to select a scan group after pushing and
holding [Scan A Start/Stop]/[Scan B Start/Stop].
Push to select a BIIS code, status number or SDM
after pushing [Digital].
Push to select the desired transceiver alias or
message channel while in the transceiver alias or
SCAN B KEYSCAN B KEYSCAN B KEYSCAN B KEY
Push to start and cancel scanning operation. In
case of transmission during scan, pauses
scanning. Scanning resumes after passing a
specified time period.
Push and hold this key for 1 sec. to indicate the
scan group, then push [CH Up] or [CH Down] to
select the desired group.
SCAN TAG KEYSCAN TAG KEYSCAN TAG KEYSCAN TAG KEY
Push to add or delete the selected channel to the
scan group.
PRIORITY CHANNEL KEYSPRIORITY CHANNEL KEYSPRIORITY CHANNEL KEYSPRIORITY CHANNEL KEYS
Push to select Priority A or Priority B channel.
Push and hold [Prio A (Rewrite)] to rewrite the Prio
A channel
MRMRMRMR----CH 1/2/3/4 KEYSCH 1/2/3/4 KEYSCH 1/2/3/4 KEYSCH 1/2/3/4 KEYS
Push to select an operating channel directly.
MONITOR KEYMONITOR KEYMONITOR KEYMONITOR KEY
Mute and release the CTCSS (DTCS) or 2-tone
* Assigned functional key selection depends on programming software setup.
** The functions exclusive to BIIS mode are indicated in Green.
18
message channel while in the transceiver alias or
message channel selection mode.
BANK SELECT KEYBANK SELECT KEYBANK SELECT KEYBANK SELECT KEY
Push this key, then push [CH Up] or [CH Down] to
select the desired bank.
SCAN A KEYSCAN A KEYSCAN A KEYSCAN A KEY
This key’s operation depends on the Power ON
Scan setting.
When the power ON scan function is turned OFF;When the power ON scan function is turned OFF;When the power ON scan function is turned OFF;When the power ON scan function is turned OFF;
Push to start and cancel scanning operation. In
case of transmission during scan, cancels
scanning.
When the power ON scan function is turned ON;When the power ON scan function is turned ON;When the power ON scan function is turned ON;When the power ON scan function is turned ON;
Push to pause scanning. Scanning resumes after
passing a specified time period. In case of
transmission during scan, pauses scanning.
Scanning resumes after passing a specified time
period specified.
Push and hold this key for 1 sec. to indicate the
scan group, then push [CH Up] or [CH Down] to
select the desired group.
Mute and release the CTCSS (DTCS) or 2-tone
squelch mute. Open any squelch/deactivate any
mute while pushing this key. (LMR operation only)
Activates one of (or two of) the following functions
on each channel independently: (PMR or BIIS
PMR operation only)
• Push and hold to un-mute the channel (audio is
emitted; ‘Audible’ condition).
• Push to mute the channel (sets to ‘Inaudible’
only).
• Push to un-mute the channel (sets to ‘Audible’
only).
• Push after the communication is finished to
send a ‘reset code’.
NOTE:NOTE:NOTE:NOTE: The un-mute condition (‘Audible’ condition)
may automatically return to the mute condition
(‘Inaudible‘ condition) after a specified period.
LOCK KEYLOCK KEYLOCK KEYLOCK KEY
Push and hold to electronically lock all
programmable keys except the following: [Call] (incl.
Call A and Call B), [Moni(Audi)] and [Emergency].
OUTPUT POWER SELECTION KEYOUTPUT POWER SELECTION KEYOUTPUT POWER SELECTION KEYOUTPUT POWER SELECTION KEY
Push to select the transmit output power temporarily
or permanently, depending on the pre-setting.• Ask your dealer for the output power level for each
selection.
Functions Programmable to Keys
C.TONE CHANNEL ENTER KEYC.TONE CHANNEL ENTER KEYC.TONE CHANNEL ENTER KEYC.TONE CHANNEL ENTER KEY
Push to select the continuous tone channel using
[CH Up]/[CH Down] to change the tone
frequency/code setting after pushing this key for
permanent operation.
TALK AROUND KEYTALK AROUND KEYTALK AROUND KEYTALK AROUND KEY
Turn the talk around function ON and OFF.
• The talk around function equalizes the transmit
frequency to the receive frequency for transceiver-
to-transceiver communication.
WIDE/NARROW KEYWIDE/NARROW KEYWIDE/NARROW KEYWIDE/NARROW KEY
Push to toggle the IF bandwidth between wide and
narrow.• The wide passband width can be selected from 25.0 or
20.0 kHz using the CS-F33G CLONING SOFTWARE. (PMR
or BIIS PMR operation only) Ask your Dealer for details.
DTMF AUTODIAL KEYDTMF AUTODIAL KEYDTMF AUTODIAL KEYDTMF AUTODIAL KEY
Push to enter the DTMF channel selection mode.
Then select the desired DTMF channel using [CH
Up]/[CH Down] keys.
After selecting the desired DTMF channel, push
this key to transmit the DTMF code.
DTMF REDTMF REDTMF REDTMF RE----DIAL KEYDIAL KEYDIAL KEYDIAL KEY
TX CODE CHANNEL SELECT KEYTX CODE CHANNEL SELECT KEYTX CODE CHANNEL SELECT KEYTX CODE CHANNEL SELECT KEY
Push to enter the direct ID code channel selection
mode. Then set the desired channel using [CH
Up]/[CH Down]/[TX Code CH Up] or [TX Code CH
Down].
While in ID code channel selection mode, push for
1 sec. to enter the ID code edit mode for 5-tone
and MSK. Then set the desired digit using [CH
Up]/[CH Down]/[TX Code CH Up]/[TX Code CH
Down] or 10-keypad.**Depending on version
TX CODE CHANNEL UP/DOWN KEYSTX CODE CHANNEL UP/DOWN KEYSTX CODE CHANNEL UP/DOWN KEYSTX CODE CHANNEL UP/DOWN KEYS
Push to select a TX code channel directly.
ID MEMORY READ KEY (ID MEMORY READ KEY (ID MEMORY READ KEY (ID MEMORY READ KEY (PMR or BIIS PMR operation
only)
Recalls detected ID codes.• Push this key, then push [CH Up]/[CH Down] for
selection.
• Up to 5 ID’s are memorized.
Push and hold to erase the selected memorized
ID’s.
VOICE SCRAMBLER FUNCTIONVOICE SCRAMBLER FUNCTIONVOICE SCRAMBLER FUNCTIONVOICE SCRAMBLER FUNCTION
Push to toggle the voice scrambler function ON and
19
DTMF REDTMF REDTMF REDTMF RE----DIAL KEYDIAL KEYDIAL KEYDIAL KEY
Push to transmit the last-transmitted DTMF code.
CALL KEYSCALL KEYSCALL KEYSCALL KEYS
Push to transmit a 2/5-tone/BIIS ID code.•Call transmission is necessary before you call another
station depending on your signalling system.
• [Call A] and/or [Call B] may be available when your
system employs selective ‘Individual/Group’ calls. Ask
your dealer which call is assigned to each key.
EMERGENCY KEYSEMERGENCY KEYSEMERGENCY KEYSEMERGENCY KEYS
Push and hold to transmit an emergency call.
When [Emergency Single (Silent)] or [Emergency
Repeat (Silent)] is pushed, an emergency call is
transmitted without a beep emission and LCD
indication change.• If you want to cancel the emergency call, push (or
push and hold) the key again before transmitting the
call.
• The emergency call is transmitted one time only or
repeatedly until receiving a control code depending
on the pre-setting.
TX CODE ENTER KEYTX CODE ENTER KEYTX CODE ENTER KEYTX CODE ENTER KEY (PMR or BIIS PMR operation only)
Push to enter the direct ID code edit mode, for both
5-tone and MSK. Then set the desired digit using [CH
Up]/[CH Down]/[TX Code CH Up]/[TX Code CH Down]
or 10-keypad.**Depending on version
Push to toggle the voice scrambler function ON and
OFF.
COMPANDER KEYCOMPANDER KEYCOMPANDER KEYCOMPANDER KEY
Push to toggle the compander function ON and OFF.
The compander function reduces noise components
from the transmitting audio to provide clear
communication.
USER SET MODE KEYUSER SET MODE KEYUSER SET MODE KEYUSER SET MODE KEY
Push and hold to enter user set mode.• During user set mode, push this key to select an item,
and push [CH Up]/[CH Down] to change the value or
condition.
Push and hold this key again to exit user set mode.
OPT OUT KEYSOPT OUT KEYSOPT OUT KEYSOPT OUT KEYS
Push to control the optional unit connector output
signal level.
Functions Programmable to Keys
DIGITAL KEY DIGITAL KEY DIGITAL KEY DIGITAL KEY (BIIS operation only)
Push to select the call ID list, transmit message
and standby condition. Toggles between queue
channel and received message record indication
after queue channel is selected.
Push and hold to select queue channel indication.
STATUS UP/DOWN KEYS STATUS UP/DOWN KEYS STATUS UP/DOWN KEYS STATUS UP/DOWN KEYS (BIIS operation only)
While in the standby condition, push to display the
transmit status indication and select a status
number.
When a received SDM is displayed, push to cancel
the automatic scroll and scroll the message
manually.
When an SDM that contains more than 8
characters is displayed, push to scroll the
message manually.
20
3-2 Cloning Software CS-F33G
3-2-1 Basic setup of Cloning Software
Software installationSoftware installationSoftware installationSoftware installation
When installing into a Windows ® XP or Windows ® 2000
⑥ The “Choose Destination Location” will appear as
below. Then click [Next>] to install the software to
the destination folder. (e.g. C:\Program
Files\Icom\CS-F33G)
• Click [Browse...] to select another destination
folder before clicking [Next >], if desired.
System requirementsSystem requirementsSystem requirementsSystem requirements
To use this program, the following hardware and
software are required:
PCPCPCPC
• Microsoft® Windows® 98/98SE/Me/2000/XP is
installed
• With RS-232C serial port (D-sub 9-pin) or USB port
Other itemsOther itemsOther itemsOther items
• OPC-478U/478UC CLONING CABLES (USB type) or OPC-478 CLONING CABLE (RS-232C type)
NOTE:NOTE:NOTE:NOTE:
When using the OPC-478U/478UC, USB type cloning
cables, USB driver installation is necessary. The driver is
supplied with the OPC-478U/478UC. See the OPC-
478U/478UC instruction manual for the installation
details.*The USB driver, supplied with the OPC-478U/478UC, is not
supported for Microsoft® Windows® 98.
ConfirmClick to select another
destination folder.
Cloning software is used to program various
parameters of the radio like frequency, scanning
etc. Below is the explanation for the basic setup of
this programming software. Example:
Click
21
When installing into a Windows ® XP or Windows ® 2000
environment, log in as the administrator.administrator.administrator.administrator.
① Quit all applications when Windows ® is running.
② Insert the CD into the appropriate CD drive.
③ Double-click the “Setup.exe” contained in the CD.
④ The “Welcome to the InstallShield Wizard for
CSF33G” will appear as below. Click [Next>].
⑦ After the installation is completed, the “InstallShield
Wizard Complete” will appear as below. Then click
[Finish].
⑧ Eject the CD.
⑨ Program group ‘CS-F33G’ appears in the ‘Programs’
folder of the start menu, and ‘CS-F33G’ short cut
icon appears on the desktop screen.
• To uninstall the cloning software, select the
“Control Panel” in the start menu, and click the
“Add or Remove Programs.” Then, select the
program group ‘CS-F33G’ and click
[Change/Remove].
Click
Click
Click
⑤ The “User Information” will appear as below, then
type your name, your company name and the
product ID number with the following manner. Then
click [Next >].
• ID number: 272504-(6 digit serial number)
• e.g. the serial number on the CD is 000101,
enter “272504-000101” as the ID number.
Note 1: Icom distributes cloning software by CD or license. Depending on this, some information here may not apply as
written, e.g. ID number.
Note 2: Please see other documents provided by Icom regarding to Microsoft® Windows Vista™.
Basic setup of Cloning Software
ConnectionsConnectionsConnectionsConnectionsAll cloning operations are performed from the computer’s keyboard— the operation required on the transceiver side
is; First, connect the cloning cable as illustrated below. Then, rotate [VOL] to turn power ON.
Screen Screen Screen Screen descriptiondescriptiondescriptiondescription
22
①①①① FILE MENU [File]FILE MENU [File]FILE MENU [File]FILE MENU [File]
Used for saving memory channel contents, printing
the pre-programmed information or exiting the
program, etc.
②②②② VIEW MENU [View]VIEW MENU [View]VIEW MENU [View]VIEW MENU [View]
• Selects the displayed font size.
•Turn the Toolbar ON or OFF.
③③③③ COM PORT MENU [COM Port]COM PORT MENU [COM Port]COM PORT MENU [COM Port]COM PORT MENU [COM Port]
• Click to display the COM port (1 to 4 and More)
setting dialog box.
• Set the transfer speed (Normal or High).
NOTE: ‘Check the following’ dialog box appearsNOTE: ‘Check the following’ dialog box appearsNOTE: ‘Check the following’ dialog box appearsNOTE: ‘Check the following’ dialog box appears
when the COM port is not set correctly.
④④④④ CLONING MENU [Clone]CLONING MENU [Clone]CLONING MENU [Clone]CLONING MENU [Clone]
Click to display cloning menu and cloning information
dialog box.
⑤⑤⑤⑤ MODEL MENU [Model]MODEL MENU [Model]MODEL MENU [Model]MODEL MENU [Model]
Select the appropriate model type which you are
going to clone.
⑥⑥⑥⑥ HELP MENU [Help]HELP MENU [Help]HELP MENU [Help]HELP MENU [Help]
Click to display the help contents and cloning
software revision information.
⑦⑦⑦⑦ TOOL BARTOOL BARTOOL BARTOOL BAR
Shortcut buttons appear on the tool bar when the
tool bar indication is turned ON in the [View] menu.
⑧⑧⑧⑧ TREE VIEW SCREENTREE VIEW SCREENTREE VIEW SCREENTREE VIEW SCREEN
Click the folder icon which you want to edit.
⑨⑨⑨⑨ CONTENTS LIST SCREENCONTENTS LIST SCREENCONTENTS LIST SCREENCONTENTS LIST SCREEN
Display the contents list (Memory CH information,
Common settings, etc.).
Basic setup of Cloning Software
LMR (2-Tone)
PMR (5-Tone/DTMF)
BIIS PMR
MDC LMR
MDC PMR
Programming informationProgramming informationProgramming informationProgramming information• Read all the transceiver cloning data into the PC before starting editing with this software. Otherwise the frequency data may not be cloned properly to your transceiver.
• Select the model type.- LMR :Land Mobile Radio. 2-Tone function is available.
- PMR :Private Mobile Radio. 5-Tone function is available.
- BIIS PMR :Binary Interchange of Information and Signalling. MSK and 5-Tone functions are available.
-MDC LMR :Mainly uses in North America which provides 2-Tone signalling feature.
-MDC PMR :Mainly uses in Europe and other countries which provides 5-Tone signalling feature.
-
LMR PMR BIIS PMR MDC LMR MDC PMR
2-TONE
5-TONE
23
Edit… Enter
-------------------------------
Copy Ctrl+C
Paste Ctrl+V
-------------------------------
Up Ctrl+Up
Down Ctrl+Down
-------------------------------
Clear
Delete Del
Insert Ins
-------------------------------
Help
RX/TX
Enters the specified receive and transmit frequencies in RX and TX
columns, within the following frequency range respectively.
IC-F33G/F34G:136 to174 MHz (2.5k, 3.125k and 7.5k step s only)
IC-F43G/F44G:420 to 470, 450 to 512, 450 to 520 MHz (depending on version)
(5k, 6.25k,7.5k steps only)
NOTE:
The frequencies available for use differ depending on the channel step.
Frequencies that can be cleanly divided by the channel step selected
can be programmed.
Please see the example below.
400.00625 (MHz) ÷ 6.25 (kHz) = 64001.000
So, 400.00625 MHz can be used.
400.00750 (MHz) ÷ 7.5 (kHz) = 53334.333….
This frequency cannot be divided cleanly, so, therefore it cannot used.
Edit menu
Help screen
BIIS 1200
MDC 1200
• Double click the desired cell in the memory channel screen directory, or right click the cell then click [Edit… Enter][Edit… Enter][Edit… Enter][Edit… Enter].
- You can click the pull down menu to select and change the channel setting depends on the item.
-- You can edit it directly.
• Click [Help] [Help] [Help] [Help] to display the help screen for the item.
3-2-2 Cloning Items for Conventional Mode
The Memory CH, MDC, DTMF, Continuous Tone, SCAN,Memory CH, MDC, DTMF, Continuous Tone, SCAN,Memory CH, MDC, DTMF, Continuous Tone, SCAN,Memory CH, MDC, DTMF, Continuous Tone, SCAN,
2222----Tone/5Tone/5Tone/5Tone/5----Tone Tone Tone Tone and Common Common Common Common items allow you to set the
transceiver customized.
Memory CHMemory CHMemory CHMemory CH
The ‘Memory CH’ window allows you to edit the channel
information.
Bank OperationBank OperationBank OperationBank Operation
Specify a bank conditions, each bank name and
capacity (number of channels). And also, shows the
number of memory channels condition for reference.
BankBankBankBank
Specify the operating frequency and details of the
operating conditions for each memory channel that is
assigned in the bank.
NOTE: NOTE: NOTE: NOTE: Program the RX frequency first, otherwise no
setting can be done.
DTMFDTMFDTMFDTMF
DTMF Autodial/SettingDTMF Autodial/SettingDTMF Autodial/SettingDTMF Autodial/Setting
Edit the DTMF Autodial Code, Text, and then set the
time period/signal length for the DTMF Timer, First
Timer and M # Timer.
5555----Tone Tone Tone Tone (Available only when PMR is selected)
RX Code CHRX Code CHRX Code CHRX Code CH
Set the RX code channel items such as RX Code, Text,
ID Dec, Bell, ABC and Beep.
RX Code SettingRX Code SettingRX Code SettingRX Code Setting
Set the RX code timer for Link A, ID Decode and
Beep Repeat, and set the Compare Digit for decode
action.
TX Code CHTX Code CHTX Code CHTX Code CH
Set the TX code channel items for TX Code, Input
Digit, Text, Update, ABC Dec/Aud and Sel.
TX Code SettingTX Code SettingTX Code SettingTX Code Setting
Set the TX code timer items such as Long Tone, and
set the Displayed digit, PTT Call at Inaudible and
special tone items.
FormatFormatFormatFormat
Set the time period for the Tone Period, Notone
Timer and Tone Length in the format.
User ToneUser ToneUser ToneUser Tone
Set the tone frequency for the Encode and Decode
Low/High respectively.
CommonCommonCommonCommon
Cloning itemsCloning itemsCloning itemsCloning items
24
Timer and M # Timer.
Continuous ToneContinuous ToneContinuous ToneContinuous Tone
Continuous Tone/SettingContinuous Tone/SettingContinuous Tone/SettingContinuous Tone/Setting
Set the RX/TX Continuous Tone frequency, and then
set the Continuous Tone Setting items such as Tone
Burst and User CTCSS Freq (Hz).
SCANSCANSCANSCAN
Scan List/SettingScan List/SettingScan List/SettingScan List/Setting
Set the Scan List settings such as Mode type and
Display Text. And set the timer items for Stop,
Resume and Fast/Slow Scan, then turn the Power
ON Scan and Auto CH Call functions ON or OFF.
2222----Tone Tone Tone Tone (Available only when LMR is selected)
Code CHCode CHCode CHCode CH
Set the 2-Tone code channel items such as 1st/2nd
Frequency, Tone Period, Text and TX Code Type.
RX Code SettingRX Code SettingRX Code SettingRX Code Setting
Set the RX code timer for Notone, Group and Beep
Repeat.
CommonCommonCommonCommon
Key & Display AssignKey & Display AssignKey & Display AssignKey & Display Assign
The desired functions can be assigned to
[Emergency], [Monitor], [Up], [Down], [P0], [P1], [P2]
and [P3] programmable function keys. And set the
10-keypad operation*, beep audio frequency,
Opening Text, MR/Code Display, Rotary Selector,
Scroll Timer*, RF Power selection and Move to Prio A
CH function.
*Available only when BIIS PMR is selected
Set ModeSet ModeSet ModeSet Mode
Set the condition of the set mode items such as
Backlight, Beep and SQL Level. And select the set
mode “Enable” or “Inhibit” (on the transceiver) for
each item.
CommonCommonCommonCommon
Commonly set items such as Clone Comment 1/2,
User Password, PWR ON Password, Auto Reset Timer
A/B, Inactive Timer, Scrambler, Emergency and Man
Down function items.
Character EditorCharacter EditorCharacter EditorCharacter Editor
You can make an original character (Max. 16
characters) and use it to indicate on the LCD.
NOTE: NOTE: NOTE: NOTE: The above instructions are for reference only.
Please refer to the HELP file of the cloning software
for the function or setting details.
3-2-3 Cloning Items for BIIS 1200
ID RangeID RangeID RangeID Range
IDIDIDID IndividualIndividualIndividualIndividual
Individual ID must be within the range of the
Individual ID range, specified by the Group ID range
setting.
GroupGroupGroupGroup
Set the desired Group ID within 0001 to 4095 for
group calls. (Start: 4000, End: 4095 are default)
When the Group ID range is set, the individual ID
range is set automatically. In the same system, the
same ID range must be set.
CommonCommonCommonCommon
Set the Common ID within 0000 to 4095 range.
The same ID must be set for all transceivers that are
going to communicate in the group. The base station
can communicate to all stations when changing the
Common ID setting when used with the PC control
command.
Country CodeCountry CodeCountry CodeCountry Code
Select the appropriate country code, specified by ETS
300 230, from the list. The same country code must
MSKMSKMSKMSK Display TextDisplay TextDisplay TextDisplay Text
Enter up to an 8-digit text message to display on the
function display when the corresponding ID code is
received.
Decode ActionDecode ActionDecode ActionDecode Action AlertAlertAlertAlert
Select the desired alert beep type. Emits the alert
beep when receiving a signal with a matched ID (own
or group).
NullNullNullNull : Beep emission (or non emission) is
retained even when the matched RX code
signal is received.
OFFOFFOFFOFF : Repeated beep emission is turned OFF.
PiPiPiPi : 1 high beep once.
PiPiPiPiPiPiPiPi : 2 high beeps once.
PiRoPiRoPiRoPiRo : 1 high and 1 low beeps 3 times.
Pi/RPi/RPi/RPi/R : 1 high beep repeated at the selected time
period*.
PiPiPiPiPiPiPiPi/R/R/R/R : 2 high beeps repeated at the selected
time period*.
PiRoPiRoPiRoPiRo/R/R/R/R : 1 high, 1 low beeps 3 times, repeated at
the selected time period*.
25
300 230, from the list. The same country code must
be set to all transceivers in that country. Select
'Others' when no appropriate country code is listed.
Each ID and code is transmitted in the sequence as
follows when making a call.
Killer IDKiller IDKiller IDKiller ID
Set the desired killer ID which disables the
transceiver's operation. When receiving a call with
the killer ID, the stun function will be activated. In
this case, passcode input is necessary after turning
power ON, and the transceiver cannot be operated
until entering the correct passcode.
Own ID/GroupOwn ID/GroupOwn ID/GroupOwn ID/Group
ID CodeID CodeID CodeID Code
IDIDIDID
Enter the Own ID for the transceiver into No. 0 within
the Individual ID range. Enter the Group ID into No.1
to No.7 within the Group ID range.
The transceiver is always standing-by with the own ID
during MSK operation. The group ID for stand-by can
be selected for each independent operating channel.
*When selecting a repeat type alert, set the desired
time period for repeat in the Beep/Alert Timer Beep/Alert Timer Beep/Alert Timer Beep/Alert Timer in MSK-
Config. The Beep/Alert Timer Beep/Alert Timer Beep/Alert Timer Beep/Alert Timer setting is also used for the
alert beep emission for status call reception.
Bell IconBell IconBell IconBell Icon
Select the desired bell indicator condition when
receiving a signal with a matched ID (own or group).
OFFOFFOFFOFF : The bell indicator goes off.
ONONONON : The bell indicator appears until operating
a key.
BlinkBlinkBlinkBlink : The bell indicator blinks until operating a
key.
Call List Call List Call List Call List IDIDIDID
Enter the other transceiver's own (individual) ID and
group ID. The IDs can be selected when pushing
[DIGITAL] or [TX Code CH Select].
Input DigitInput DigitInput DigitInput Digit
Set the editable digit for direct ID input by pushing
[TX Code Enter]. When no ID code entering is
necessary, remove the all check-mark () from the
check-box.
TextTextTextText
Enter an 8-digit text to display the text message
instead of the ID number indication.
Cloning Items for BIIS 1200
UpdateUpdateUpdateUpdate
Select the ID code overwrites capability.
The directly entered ID can be overwritten via [TX
Code Enter] when "Enable" is selected. Select
"Disable" when it is necessary to leave the content as
it is.
SelSelSelSel
Select "Disable" to prevent the desired ID from
appearing on the function display when selecting the
status via [DIGITAL], [Status Up/Down].
Timing & ErrorTiming & ErrorTiming & ErrorTiming & Error
Call ParameterCall ParameterCall ParameterCall Parameter NANANANA
Set the desired number of repeating
acknowledgment calls in a calling sequence from 1
to 8. (default: 1)
NMNMNMNM
Set the desired number of repeating messages in a
calling sequence from 1 to 8. (default: 1)
NOTE: NA and NM
When setting 2 or a larger number, the calling
AckAckAckAck LET TimerLET TimerLET TimerLET Timer
Set the time period for transmission delay for the
transmit signal and MSK modulation when
transmitting an acknowledgment call.
NOTE: Call LET Timer and Ack LET Timer
The default setting is 50 msec., however, set longer
time period when communicating through a repeater
26
When setting 2 or a larger number, the calling
succeed rate becomes higher even in bad signal
conditions. Also, a TAC timer setting longer than the
default must be set to receive all the
acknowledgment calls or messages according to this
setting. All of the transceivers must be set with the
same value for all NA, NM and TAC Timer for all of
the transceivers to be able to communicate.
The total calling time becomes longer in this case.
NRNRNRNR
Set the desired number of repeating transmission
calls when no acknowledgment call is received, from
1 to 8. (default: 3) This setting is different from the
NA and NM settings. The desired number can be set
for each transceiver independently.
TACTACTACTAC
Set the waiting time period for receiving an during a
call within 0.01 to 2.55 sec. When no
acknowledgment is received in this set period, the
transceiver repeats the call transmission the number
of times set in NR. The default setting is 0.5 sec.,
however, set the longer time period when
communicating through a repeater using CTCSS,
according to the operating style. Set 0.8 sec.
(approx.) for CTCSS operation.
Call LET TimerCall LET TimerCall LET TimerCall LET Timer
Set the time period for transmission delay for the
transmit signal and MSK modulation when
transmitting a call.
time period when communicating through a repeater
using CTCSS, according to the operating style.
The communication may not be successful when the
setting is shorter than the default time period,
because the time periods may be different between
each transceiver.
Set 350 msec. (approx.) for CTCSS operation.
Busy Check TimerBusy Check TimerBusy Check TimerBusy Check Timer
Set the stand-by time period for the status call
transmission (when the status-Priority is set to
"Normal") when the operating channel is busy.
When the signal disappears within the set period, a
status call will be made. However, the status call will
be canceled when the channel is busy for the set
period.
• Max. 255 sec. can be set.• Enter 0 sec. to cancel the call immediately when the channel is busy.
Cloning Items for BIIS 1200
ConfigConfigConfigConfig....
Encode SettingEncode SettingEncode SettingEncode Setting
PTT CallPTT CallPTT CallPTT Call
Select the call operation capability with PTT.
When "Enable" is selected, the PTT functions as
[CALL] key on an MSK channel during "Inaudible"
mode.
PrePrePrePre----EmphasisEmphasisEmphasisEmphasis
Select the MSK signal modulation type from "PM"
and "FM".
SYNC WordSYNC WordSYNC WordSYNC Word
Set the synchronous signal word in the system with a
4-digit hexadecimal word. The same word must be
set for all transceivers to be communicated to.
• B433" is mainly used in France.• Do not set "C4D7". This word is used in the MPT trunking system.
ANIANIANIANI
PTT Side TonePTT Side TonePTT Side TonePTT Side Tone
Select the beep emission capability to announce the
communication timing during digital ANI operation
with log-in setting.
A short beep sounds after the digital ANI signal is
ANI DisplayANI DisplayANI DisplayANI Display
When matched digital ANI signal is received, the ANI
number or Text (programmed in Call List screen) is
displayed on the LCD for the specified time period*.
OFFOFFOFFOFF : : : : The received ANI number or
programmed text (in Call List
screen when matched) is not
displayed on the LCD.
AudAudAudAud : The received ANI number or
programmed text (in Call List
screen when matched) is
displayed on the LCD for the
specified time period* in Audible
mode.
Aud+In_AAud+In_AAud+In_AAud+In_A : The received ANI number or
programmed text (in Call List
screen when matched) is
displayed on the LCD for the
specified time period* in both
Audible and Inaudible mode.
*Time period is set in the ANI Display Timer as ANI Display Timer as ANI Display Timer as ANI Display Timer as follows.
ANI Display TimerANI Display TimerANI Display TimerANI Display Timer
27
with log-in setting.
A short beep sounds after the digital ANI signal is
transmitted when set to ON.
Decode SettingDecode SettingDecode SettingDecode Setting
Beep/Alert TimerBeep/Alert TimerBeep/Alert TimerBeep/Alert Timer
Set the Beep/Alert repeat timer within 0 to 60 sec.
range. This timer is used for the alert beep emission
and functions when receiving the MSK or status call
with one of the 'Repeat' items is set.
The 'Repeat' item is selected at Alert item in Own
ID/Group-Decode Action (MSK call) and at Beep item
in Status.
Mute MSK ToneMute MSK ToneMute MSK ToneMute MSK Tone
Select the MSK signal mute function ON and OFF.
This function mutes the MSK audio coming from the
other stations, while the transceiver is in the 'Audible'
mode (after the connection is successful, while
monitoring, etc.).
The MSK signal mute function mutes only when the
signal including the same SYNC Word. The MSK
signal can be heard when the signal an unmatched
SYNC Word.
ANI Display TimerANI Display TimerANI Display TimerANI Display Timer
Set the time period for the received ANI number or
programmed text (in Call List screen when matched)
indication on the LCD.
Up to 25.5 sec. can be set. (0.1 step)
Status SettingStatus SettingStatus SettingStatus Setting Fixed Base IDFixed Base IDFixed Base IDFixed Base ID
Enter the desired station ID.
A status message is transmitted to this station all the
time on the channel with "Base" as the setting for the
Send Status in Memory CH screen.
This ID is independent from the ID programmed in
the Fixed Base ID in GPS Setting.
Send Status on Send Status on Send Status on Send Status on PrioAPrioAPrioAPrioA CHCHCHCH
When "Enable" is set, the status message is always
transmitted on the Priority A channel. Specifying the
Priority A to the desired MSK channel is necessary.
When "Base" is selected for the Send Status in
Memory CH screen, the Status call is always
transmitted to the specified ID station (Fixed Base
ID).
Power ON Status23Power ON Status23Power ON Status23Power ON Status23
Set "Enable" to transmit the Status 23 when turning
the power ON.
Power OFF Status19Power OFF Status19Power OFF Status19Power OFF Status19
Set "Enable" to transmit the Status 19 when turning
the power OFF.
Cloning Items for BIIS 1200
GPS SettingGPS SettingGPS SettingGPS Setting Fixed Base IDFixed Base IDFixed Base IDFixed Base ID
Enter the desired station ID.
The position data is transmitted to this station all the
time when the Send GPS fix to BaseSend GPS fix to BaseSend GPS fix to BaseSend GPS fix to Base, as below, is set
to "Enable" also.
This ID is independent from the ID programmed in
the Fixed Base ID Fixed Base ID Fixed Base ID Fixed Base ID in Status Setting.
Send GPS fix to BaseSend GPS fix to BaseSend GPS fix to BaseSend GPS fix to Base
Turn the sending position data to the fixed station
capability ON and OFF.
Select "Enable" to send the position data to the
specified station (Fixed Base ID Fixed Base ID Fixed Base ID Fixed Base ID as above).
AutoAutoAutoAuto
Turn the automatic position data transmission
capability ON and OFF.
The position data is automatically transmitted at the
specified time and interval when "Enable" is
selected.
The time and interval are specified in Time Marker Time Marker Time Marker Time Marker
and Interval Timer Interval Timer Interval Timer Interval Timer as follows.
The transceiver reads the UTC time data from the
Send with LogoffSend with LogoffSend with LogoffSend with Logoff
Turn the automatic position data transmission
capability at log-off ON and OFF (each time when PTT
is released).
Send with StatusSend with StatusSend with StatusSend with Status
The position data is transmitted after making a
Status call when "Enable" is selected.
The position data is transmitted to the same station
that the Status call was made to.
Send with SDMSend with SDMSend with SDMSend with SDM
The position data is transmitted after an SDM
transmission when "Enable" is selected.
The position data is transmitted to the selected
station for the SDM transmission in this case.
Send with EmergencySend with EmergencySend with EmergencySend with Emergency
The position data is transmitted after an emergency
call via [Emergency] key, when "Enable" is selected.
The position data is transmitted to the station that is
specified in the emergency status setting in this
case.
Send at Send at Send at Send at ManDownManDownManDownManDown
The position data is transmitted after a Man Down
Emergency call.
28
The transceiver reads the UTC time data from the
GPS receiver after 10 minutes from turning the
transceiver power ON, then specifies the time
marker. Therefore, the GPS receiver must receive the
time data signals properly before the UTC time is
read into the transceiver.
Check the GPS data is received properly by sending
the Status 24 (GPS Request) to ensure the GPS Auto
TX activate.
Time Marker [Time Marker [Time Marker [Time Marker [mm:ssmm:ssmm:ssmm:ss]]]]
Set the desired Marker time for the automatic
position transmission capability.
The Marker time is specified by the set value and
based on each second a UTC hour.
Set a different Marker time for each transceiver to
avoid interference caused by the simultaneous
transmission of position data.
Interval Timer [Interval Timer [Interval Timer [Interval Timer [mm:ssmm:ssmm:ssmm:ss]]]]
Set the desired Interval time.
NOTE: Time Marker and Interval TimerNOTE: Time Marker and Interval TimerNOTE: Time Marker and Interval TimerNOTE: Time Marker and Interval Timer
For example: When 5 minutes is set as the Time
Marker, and 10 minutes is set as the Interval Timer,
the first position data is transmitted every hour 5
minutes after the hour. The position data from the
second transmission onward, is transmitted in 10
minute intervals.
Emergency call.
SentenceSentenceSentenceSentence
Select the desired position data sentence format to
be transmitted from $GPRMC, $GPGGA and $GPGLL.
etc.etc.etc.etc. PTT Enable at ConnectPTT Enable at ConnectPTT Enable at ConnectPTT Enable at Connect
Select the [PTT] operation when the MSK ID code is
transmitted. (PTT call capability is permitted in PTT PTT PTT PTT
CallCallCallCall.)
DisableDisableDisableDisable : Push [PTT] to transmit the MSK ID code on
the selected channel. Then push [PTT]
again to talk.
EnableEnableEnableEnable : Push and hold [PTT] to transmit the MSK ID
code on the selected channel, then you can
talk to the party at connected without [PTT]
releasing.
Cloning Items for BIIS 1200
Status Status Status Status
RX StatusRX StatusRX StatusRX Status
Display TextDisplay TextDisplay TextDisplay Text
Enter an 8-digit text to display on the function display
instead of the status number.
The programmed text appears not only when receiving
the status.
No text message is displayed when receiving the Status
24, and the text edit is restricted in the cloning software
because the Status 24 is a fixed function for the
position request.
BeepBeepBeepBeep
Select the desired alert beep type for a Status call
reception.
Null : Beep emission (or non
emission) is retained even when the matched RX code
signal is received.
OFF : Repeated beep emission is turned
OFF.
Pi : 1 high beep once.
PiPi : 2 high beeps once.
PiRo : 1 high and 1 low beeps 3 times.
Pi/R : 1 high beep repeated at the selected
TX StatusTX StatusTX StatusTX Status Display TextDisplay TextDisplay TextDisplay Text
Enter an 8-digit text to display on the function display
instead of the status number.
The programmed text appears when the TX status is
selected via [DIGITAL], [Status Up/Down].
PriorityPriorityPriorityPriority
Select the desired transmission priority for the status
call when the operating channel is busy.
NormalNormalNormalNormal : Status call will be canceled.
HighHighHighHigh : Status call is made even if the channel
is busy. However, the calling success is
not guaranteed.
Select "High" for the Status 22 (emergency call),
because the status call is repeated until receiving an
acknowledgment call. Even if "Normal" is selected,
the status call can be made when using with the
Busy Check Timer. When the timer is set, the
transceiver watches for a signal, and transmits the
status after the signal disappears. When the signal
still available for the set time period, the status call
is canceled.
29
Pi/R : 1 high beep repeated at the selected
time period*.
PiPi/R : 2 high beeps repeated at the selected
time period*.
PiRo/R : 1 high, 1 low beeps 3 times, repeated
at the selected time period*.
*When selecting a repeat type alert, set the desired
time period for repeat in the Beep/Alert Timer in MSK-
Config.
Auto TXAuto TXAuto TXAuto TX
Select the auto transmit function, when receiving the
Status call, from ON and OFF.
The transmission time period is set in the Auto TX Timer
in Common screen.
'Inaudible' mode may be selected by the station that
requests the Auto TX, because it is transmitting a status
call; audio cannot be heard. So, use the PC control
command to turn the MSK mute OFF (base station), or
use an extra transceiver for monitoring.
is canceled.
The timer is set in the Busy Check Timer Busy Check Timer Busy Check Timer Busy Check Timer in the MSK
Timing & Error screen.
SelSelSelSel
Select "OFF" for the desired status message to do
not appear on the function display when selecting
the status via [DIGITAL], [Status Up/Down].
SDM SDM SDM SDM
SDM (Short Data Message)SDM (Short Data Message)SDM (Short Data Message)SDM (Short Data Message)
Enter up to the desired 8-digit short data message
(Direct input).
Max. 95 character messages can be transmitted at
one time via the PC control command. The received
message records are displayed by pushing and
holding [DIGITAL], and the received message records
are memorized up to a max. 95 characters.
SelSelSelSel
Select "OFF" for the desired SDM to do not appear on
the function display when selecting the SDM via
[DIGITAL], [Status Up/Down].
NOTE: NOTE: NOTE: NOTE: The above instructions are for reference only.
Please refer to the HELP file of the cloning software
for the function or setting details.
3-3 2-Tone (LMR) Signalling
LMR (2-Tone)
PMR (5-Tone/DTMF)
BIIS PMR
MDC LMR
MDC PMR
What is 2What is 2What is 2What is 2----Tone Signalling?Tone Signalling?Tone Signalling?Tone Signalling?
1. Originally called “Quick Call”, this signalling protocol
was developed by Motorola in the 1950’s.
2. 2-Tone (Quick Call) was designed to add Squelch
specificity especially for emergency service radios.
3. LMR consists of two distinct signals sent over the air
to a radio or a group.
4. Each tone can be configured within a 250 Hz and
3300 Hz tone frequency.
in the proximity of the radio. This is also very useful
in emergency cases where the user may not be able
to trigger the microphone.
5. “Stun/Kill – This function allows the dispatch
console to disable, temporarily or permanently, a unit
using the 2-Tone capabilities. When “Stun” is used,
the unit may regain its functionality by entering a
password. When Kill is used, the radio only regains
functionality by reprogramming the unit using the
cloning software.
30
5. Normally, the duration of the tones varies from one
(1) to three (3) seconds in length no space between
the tones. Tone lengths of up to 10 seconds are
commonly seen in existing applications.
6. ICOM radios allow variable tone periods and spaces
(no tone) between the tones.
2222----Tone Features Tone Features Tone Features Tone Features
1. “Selective Calling” – allows the dispatch console to
page an individual unit. Early models only allowed 1
(one) encoding tone set per channel or up to 3
(three) receive tones in the radio. Newer ICOM radios
allows the programming of up to 10 (ten) tones that
can be used all in one channel if necessary.
2. “Group Calling” - allows the dispatch console to page
a group.
3. “Answer Back Call” – Also known as “Radio Check”
allows the dispatch console or another portable, to
send a tone to a particular radio and when the target
radio receives the tone it answers back with another
tone. This function serves as a tool to verify if a unit
is “ON” and within range.
4. “Auto Transmit” – Also known as “Radio Spy” allows
the dispatcher to send a 2-Tone signal to the radio
causing it to open its transmitter microphone audio
(Hot Mic) in order to listen to whatever is happening
6. “Scan Start/Cancel” – Using 2-Tone a dispatcher can
send a signal to a radio or a group to commence the
“Scan” function of the radio. If used with a group of
users, this feature allows the dispatcher to regroup
everyone in a different, but common channel. This
feature is also known as “Radio Regroup”.
ICOM ICOM ICOM ICOM 2222----Tone Tone Tone Tone Radio Enhancements include:Radio Enhancements include:Radio Enhancements include:Radio Enhancements include:
1. RX Code Text – Allows the programmer to add an
“Alpha Numeric” text tag to each tone for
identification at decode and encode if the unit has a
display.
2. Variable Signals – This allows the user/programmer
to set the “Beep and Bell” to different formats for
easier identification when a signal is received.
3. Tones Assignable on a Channel by Channel Basis –
The newer Icom radios allow the programmer to
enter in ten (10) tone sets, which can be used for
both encode AND decode if necessary. Each channel
has the capability to use all tones for both encode
and decode, if programmed correctly.
4. Multiple Tone Sets per Channel – This also allows
the programmer to set all ten (10) tones on a single
channel if it was deemed necessary. Each channel
allows a programmer to use a combination of tones
per channel as needed.
3-4 5-Tone (PMR) Signalling
What is 5What is 5What is 5What is 5----Tone Signalling?Tone Signalling?Tone Signalling?Tone Signalling?
1. Although it is dubbed as 5-Tone, this signalling
protocol consists of a fast data burst of one (1) to
seven (7) frequency tones that can selectively signal
a radio.
2. Originally a European signalling protocol, 5-Tone has
numerous formats such as:
a. CCIR
b. ZVEI1
c. ZVEI2
5555----Tone Format StructureTone Format StructureTone Format StructureTone Format Structure
1. Unlike 2-Tone, where the programmer must know the
frequency to be used on each tone, 5-Tone does not
require knowledge of the frequencies to be used.
2. Each digit in the sequence is already predefined with
a specific frequency depending on the format
selected in the Tone form section of the
programming.
3. All the programmer needs to know is what format is
being used and what code needs to do what. The
LMR (2-Tone)
PMR (5-Tone/DTMF)
BIIS PMR
MDC LMR
MDC PMR
31
c. ZVEI2
d. DZV1
e. EEA
f. EEA2
g. DAPL
h. EIA
i. DTMF (Dual Tone Multi Frequency) *Check
model for availability.
3. EIA is the International Open Standard set by the
Electronics Industries Association.
4. 5-Tone adds specificity to the squelch abilities of
commercial radios.
Where to activate 5Where to activate 5Where to activate 5Where to activate 5----Tone Tone Tone Tone
1. Enable the radio in PMR mode by selecting the PMR
Model in the Model section of the cloning software.
2. To create the 5-Tone TX list, click on the 5-Tone
folder and select the “TX Code CH” icon.
3. In this section the user can create up to 32 encode
able tone sequences.
4. Each of these tone sequences can be identified with
an alias on the list.
being used and what code needs to do what. The
system does the rest.
4. If there was a need, although it is not highly
recommended, the tone formats can be modified to
specific needs.
5. The 5-Tone Format section of programming allows
the programmer to view and modify three (3) aspects
of the 5-Tone format.
6. Tone Period - is the length of the encoded tone.
7. Notone Timer – is the space required between tones
for proper decoding (tone spread).
8. Tone Length – is the time the radio takes to decode
a tone.
*** Re-emphasize ICOM strongly recommends that
programmers do NOT alter any data in the Format
screen
5-Tone (PMR) Signalling
Why chose 5Why chose 5Why chose 5Why chose 5----Tone?Tone?Tone?Tone?
1. 5-Tone is a non-proprietary signalling protocol that
allows the Icom radio to inter-operate with other
brands using the 5-Tone signalling.
2. This protocol also allows a mixed fleet operation.
3. It is faster than 2-Tone by employing a quick data
burst.
4. Customers are familiar with the protocol since it is an
Industry Standard in USA, Europe, and Asia.
5. Many manufacturers built dispatch consoles with this
capability.
6. 5-Tone offers flexible muting characteristics.
5555----Tone FeaturesTone FeaturesTone FeaturesTone Features
1. Selective Calling” – allows the dispatch console to
page an individual unit.
2. “Group Calling” - allows the dispatch console to page
a group.
7. 5-Tone allows the PTT ID functionality on the radio.
8. As with 2-Tone, PMR also provides audible alerts,
emergency signalling and Dispatch functionality
making it a workable upgrade to an existing fleet.
***All these functions can be accomplished with
individual radios also.
5555----Tone EnhancementsTone EnhancementsTone EnhancementsTone Enhancements
1. The PMR model and radio functionality provides the
programmer with RX Text identifiers. When a
particular 5-Tone sequence is received, a radio with
display will show the alias attributed to that tone
sequence.
2. Where applicable, this radio also has flashing
indicators, variable audible signals and beeps.
3. When transmitting a 5-Tone sequence, the radio can
select from a programmed list with aliases in order to
identify the code desired for TX.
4. PMR radios allow for TX code editing and the
creation of a custom “User Code” that will allow the
32
3. “Answer Back Call” – Also known as “Radio Check”
allows the dispatch console to send a 5-Tone
sequence to a particular radio and when the target
radio receives the tone it answers back with another
tone. This function serves as a tool to verify if a unit
is “ON” and within range.
4. “Auto Transmit” – Also known as “Radio Spy” allows
the dispatcher to send a 5-Tone signal to the radio
causing it to open its transmitter microphone audio
(Hot Mic) in order to listen to whatever is happening
in the proximity of the radio. This is also very useful
in emergency cases where the user may not be able
to trigger the microphone.
5. “Stun/Kill – This function allows the dispatch
console to disable temporarily or permanently a unit
using the 5-Tone capabilities. When “Stun” is used,
the unit may regain its functionality by entering a
password. When Kill is used, the radio only regains
functionality by reprogramming the unit using the
cloning software.
6. “Scan Start/Cancel” – Using 5-Tone a dispatcher can
send a signal to a radio or a group to commence the
“Scan” function of the radio. If used with a group of
users, this feature allows the dispatcher to regroup
everyone in a different channel. This feature is also
known as “Radio Regroup”.
creation of a custom “User Code” that will allow the
programmer to create a unique code for a customer.
5. The system also allows for a user to select the TX
codes by assigning a button on the radio.
3-5 Scan (Conventional Mode)
What is Scanning?What is Scanning?What is Scanning?What is Scanning?
The ability of a radio user to listen to radio traffic on
other channels without having to manually switch
from one channel to another.
Normal scanNormal scanNormal scanNormal scanScans all checked channels. The scan proceeds in
sequence.
Priority scan (Priority scan (Priority scan (Priority scan (PrioPrioPrioPrio----A)A)A)A)The priority A channel is selected in CH Atr in Memory
CH screen. The checked channels are scanned in
sequence while monitoring the priority A channel.
Scan ModeScan ModeScan ModeScan ModeSelect the scanning mode from Scan OFF, Mode 1
(Normal), Mode 2 (Prio-A), Mode 3 (Prio-A), Mode 2
(R.Sel) and Mode 3 (R.Sel).
Display TextDisplay TextDisplay TextDisplay Text
• Enter up to an 8-character text to indicate message, etc. during scanning and indicating the scan group.
33
Priority scan (R. Priority scan (R. Priority scan (R. Priority scan (R. SelSelSelSel))))The rotary selector channel (scan start channel) is
selected via the rotary selector. The checked
channels are scanned in sequence while monitoring
the rotary selector channel
etc. during scanning and indicating the scan group.
• Right click to display the [Edit... Enter] menu and click [Edit... Enter].
• Double click the desired character in the table or push [Space] to pick up the character.
• Push [Enter] to finish editing.
SCAN LISTSCAN LISTSCAN LISTSCAN LISTA total of 10 scanning lists/groups are available for a
wide variety and flexible scanning operation. In this
screen, program scanning condition for each
list/group.
Text ONText ONText ONText ON
Turn the text indication ON and OFF during scan.
PWR SavePWR SavePWR SavePWR Save
Turn the power save function ON and OFF during
scan. Total scanning speed is decreased when the
function is activated.
Scan (Conventional mode)
SCAN MODESCAN MODESCAN MODESCAN MODE Mode 1 (Normal): Mode 1 (Normal): Mode 1 (Normal): Mode 1 (Normal):
Normal scan. Scans all checked channels. The scan
proceeds in sequence.
• The last busy or paused channel (CH 02 as belowillustration) is selected automatically when scan is
canceled.
• TX via [PTT] is performed in the last busy or paused channel.
Mode 2 (Mode 2 (Mode 2 (Mode 2 (PrioPrioPrioPrio----A):A):A):A):
• Priority scan. The priority A channel is selected in CH Atr in Memory CH screen.
The checked channels are scanned in sequence
while monitoring the priority A channel.
• The priority A channel is selected automatically when scan is canceled during scanning.
• TX via [PTT] is performed in the priority A channel
• When scan is canceled while a signal is receiving, the channel the signal is received on is selected
automatically.
• TX via [PTT] is performed in the channel that received the signal.
• The rotary selector channel is selected automatically when scan is canceled.
• TX via [PTT] is performed in the rotary selector channel)
NOTE:
• "Mode 2 (R.Sel)"
and "Mode 3
(R.Sel)" can be
available when
"MR CH" is
selected in Rotary
Selector in Key &
Display screen.
34
Mode 3 (Mode 3 (Mode 3 (Mode 3 (PrioPrioPrioPrio----A): A): A): A):
Priority scan. The priority A channel is selected in CH
Atr in Memory CH screen.
The scanning sequence is the same as Mode 2 (Prio-
A) above.
• The priority A channel is selected automatically when scan is canceled.
• TX via [PTT] is performed in the priority A channel.
Mode 2 (Mode 2 (Mode 2 (Mode 2 (R.SelR.SelR.SelR.Sel): ): ): ):
Priority scan. The rotary selector channel (scan start
channel) is selected via the rotary selector.
The checked channels are scanned in sequence
while monitoring the rotary selector channel.
• The rotary selector channel is selected automatically when scan is canceled during
scanning.
• TX via [PTT] is performed in the rotary selector channel.
• When scan is canceled while a signal is receiving, the channel the signal is received on is selected
automatically.
• TX via [PTT] is performed in the channel that received the signal.
Mode 3 (Mode 3 (Mode 3 (Mode 3 (R.SelR.SelR.SelR.Sel): ): ): ):
Priority scan. The rotary selector channel (scan start
channel) is selected via the rotary selector. The
scanning sequence is the same as Mode 2 (R.Sel)
above.
Scan (Conventional mode)
MEMORY CHMEMORY CHMEMORY CHMEMORY CH AtrAtrAtrAtr
Select the channel attribution from Priority APriority APriority APriority A, Priority
B, Emergency and Emergency.
A: Priority AA: Priority AA: Priority AA: Priority A
“A” tagged channel becomes the priority A channel,
simply recalled by pushing [Prio A] or [Prio A
(Rewrite)] key, and also is automatically monitored
during the priority scan.
In the BIIS operation, the priority A channel can be
selected automatically when turning power ON,
transmitting/receiving a Clear Down signal, and
transmitting a status call, according to the selling.
IncIncIncInc
Select the scanning channel modification capability
from the transceiver's key.
The desired channel can be added or deleted
to/from the selected scan list by pushing [Scan
Add/Del(Tag)] key.
KeyKeyKeyKeyDealer programmable keys: [EmergencyEmergencyEmergencyEmergency]/[MonitorMonitorMonitorMonitor]/
[UpUpUpUp] /[DownDownDownDown]/[P0P0P0P0]/[P1P1P1P1]/[P2P2P2P2] and [P3P3P3P3].
These keys can each be assigned for one of several
functions.
Scan ListScan ListScan ListScan List
A total of 10 scanning lists ([1] to [0]) are available
for a wide variety and flexible scanning operation.
Click the check-box of the channel included into the
desired scan list [1] to [10]. Then, double click the
check-box [1] to [0], or push the desired key [1] to
[0] on the keyboard to toggle the selection.
Only the checked channels in the same scan list are
scanned when [Scan A Start/Stop] or [Scan B
Start/Stop] key is pushed.
The [Scan A Start/Stop] and [Scan B Start/Stop]
keys are assigned in Key & Display Assign.
35
Scan (Conventional mode)
• Push and hold this key for 1 sec. to indicate the scan group, then select the desired group using [CH Up] or
[CH Down].
Scan B Start/StopScan B Start/StopScan B Start/StopScan B Start/Stop
• Push to start and cancel scanning operation. In case of transmission during scan, pauses scanning.
Scanning resumes after a specified time period* has
passed after the transmission is finished.
• Push and hold this key for 1 sec. to indicate the
scan group, then select the desired group using [CH
Up] or [CH Down].
*Specify the time period in Auto Reset Timer Auto Reset Timer Auto Reset Timer Auto Reset Timer in Timers
screen.
Scan Add/Del(Tag)Scan Add/Del(Tag)Scan Add/Del(Tag)Scan Add/Del(Tag)
Push to add or delete the channel to/from the
selected scanning list.
PrioPrioPrioPrio A, A, A, A, PrioPrioPrioPrio BBBBPush to select the priority A/B channel programmed
in Atr in Memory CH screen respectively.
PrioPrioPrioPrio A (Rewrite)A (Rewrite)A (Rewrite)A (Rewrite)• Push to select the priority A channel programmed in Atr in Memory CH screen.
Conventional ModeConventional ModeConventional ModeConventional Mode Scan A Start/StopScan A Start/StopScan A Start/StopScan A Start/Stop
• This key operation depends on Power ON Scan
setting in Scan Setting screen.
KeyKeyKeyKeyDealer programmable keys: [EmergencyEmergencyEmergencyEmergency]/[MonitorMonitorMonitorMonitor]/
[UpUpUpUp] /[DownDownDownDown]/[P0P0P0P0]/[P1P1P1P1]/[P2P2P2P2] and [P3P3P3P3].
These keys can each be assigned for one of several
functions.
36
in Atr in Memory CH screen.
• Push for 1 sec. to reassign the operating channel for priority A channel.
When the power ON scan function is turned OFF;When the power ON scan function is turned OFF;When the power ON scan function is turned OFF;When the power ON scan function is turned OFF;
Push to start and cancel scanning operation. In case of
transmission during scan, cancels scanning.
When the power ON scan function is turned ON;When the power ON scan function is turned ON;When the power ON scan function is turned ON;When the power ON scan function is turned ON;
Push to pause scanning. Scanning resumes after a
specified time period* has passed. In case of
transmission during scan, pauses scanning. Scanning
resumes after a specified time period* has passed
after the transmission is finished.
*Specify the time period in Auto Reset Timer Auto Reset Timer Auto Reset Timer Auto Reset Timer in Timers
screen.
Scan (Conventional mode)
Power ON ScanPower ON ScanPower ON ScanPower ON Scan
Turn the power ON scan function ON to activate the
automatic scan start capability at power ON.
The scanning restart condition is selected in Auto Auto Auto Auto
Reset Reset Reset Reset in Memory CH screen, and the time period is
programmed in the Auto Reset Timer A/B Auto Reset Timer A/B Auto Reset Timer A/B Auto Reset Timer A/B and the
Inactive Timer Inactive Timer Inactive Timer Inactive Timer (available when PMR/BIIS PMR is
selected) in common screen.
TimerTimerTimerTimer
Timers are components that stop and resume scan as
well as setting channel examination times. This helps
for smooth and reliable operation.
StopStopStopStop
• How often the radio will stop and look back at the priority channel when receiving a non-priority signal
when in priority scan.
• Enter the time period for scan pausing on a busy channel (watching interval) when receiving a signal in
scan mode 2 or 3 (priority scan), specified in Scan Scan Scan Scan
ModeModeModeMode in Scan List screen.
37
Auto CH CallAuto CH CallAuto CH CallAuto CH Call
Turn the auto channel call function ON to activate the
automatic clear channel searching capability when
[Call] key is pushed (call transmission).
When [Call] key is pushed while the channel without
5-Tone is busy, the transceiver starts scanning, then
transmits the previously transmitted 5-Tone code
after a clear channel is found.
ResumeResumeResumeResume
• Upon receiving a valid signal, the radio will stop scanning while receiving the signal. Once the signal
terminates, the scan stays paused for the length of
the Resume Timer in the Scan Settings screen. Once
the Resume Timer elapses, the scan cycle re-
initiates.
• Enter the time period for resuming the scan after signal disappears.
Fast ScanFast ScanFast ScanFast Scan
• Maximum amount of time it takes to examine a frequency with no accompanying coded squelch
programmed in the Memory Channel.
• Enter the time period for scanning of each channel without CTCSS/DTCS programming. An appropriate
time is set by default and scan may not stop when
setting a value less than the default.
Slow ScanSlow ScanSlow ScanSlow Scan
• Maximum amount of time it takes to examine a frequency with coded squelch programmed in the
Memory Channel.
• Enter the time period for scanning of each channel with CTCSS/DTCS programming. An appropriate time
is set by default and scan may not stop when setting
a value less than the default.
3-6 Voice Scrambling Systems
Voice scrambling methodsVoice scrambling methodsVoice scrambling methodsVoice scrambling methodsThe built-in inversion type voice scrambler provides secure conversation. When a more secure system is required, the
32 code non-rolling-type voice scrambler UT-109 and 1020 code rolling type UT-110 are available as an option.
BuiltBuiltBuiltBuilt----in inversion type voice scramblerin inversion type voice scramblerin inversion type voice scramblerin inversion type voice scrambler
This is the scrambling system which is built-in inversion type voice scrambler inverts the high and low audio
frequencies.
Original AF
Level
Dividing
Level Dividing Frequency Inverting
Level Dividing Frequency
Variable Split and Frequency InversionVariable Split and Frequency InversionVariable Split and Frequency InversionVariable Split and Frequency Inversion
This is the scrambling system employed in the UT-109 and UT-110. The audio frequency band is divided at a specified
frequency (divided frequency) and high and low audio frequencies in each band are inverted. The divided frequency is
programmable with cloning.
Original AF
300Hz 3kHz
Level
Frequency
Inverted AF
300Hz 3kHz
Level
Frequency
38
Difference between rolling and nonDifference between rolling and nonDifference between rolling and nonDifference between rolling and non----rolling typesrolling typesrolling typesrolling types
The rolling type (in fact, hopping type is used for the UT-110) is an additional feature which provides higher
communication security. It changes the divided frequency over a specified period.
Rolling Type (UT-110)
300Hz 3kHz
Level
Frequency
Dividing Frequency is changed
over specified period
Dividing FrequencyLow High
Non-Rolling Type (UT-109)
300Hz 3kHz
Level
Frequency
Dividing Frequency is fixed
with programming
Dividing FrequencyLow High
300Hz 3kHz Frequency 300Hz 3kHz Frequency 300Hz 3kHz Frequency
Voice Scrambling Systems
Program setting for scramblerProgram setting for scramblerProgram setting for scramblerProgram setting for scrambler Common Common Common Common ---- ScramblerScramblerScramblerScrambler
• TypeSet installed voice scrambler type as UT-110 Rolling or
UT-109 Non-rolling.
As Rolling type and Non-rolling type have different
code settings, they are not compatible.
By selecting Non-rolling type in this item, you can use
the UT-109, or UT-110 as Non-rolling type.
Selectable value: Rolling or Non-rolling
NOTE:NOTE:NOTE:NOTE:
1. This item is invalid for frequency inversion type.
2. When Non-rolling type is selected, the following
setting will be invalid.
• Group CodeSet the Scrambler Group code number.
Available number: 1 to 4
NOTE: NOTE: NOTE: NOTE: This item is invalid for frequency inversion type
and Non-rolling type.
• Synchronous Capture"Synchronous capture mode" is useful when
communicating through a repeater.
However, because of voice components, the
transceiver cannot maintain synchronous mode in rare
Memory CH Memory CH Memory CH Memory CH ---- ScramblerScramblerScramblerScrambler
• ON/OFFTurn voice scrambler function ON or OFF as an initial
setting.
OFF : Turn the voice scrambler function OFF.
ON : Turn the voice scrambler function ON.
Inh : The voice scrambler function selection for
the user is inhibited.
• TypeSelect the desired voice scrambler type from UT- (UT-
109/110), Inv (Inversion) or Oth (Other-T).
UT- : The optional UT-109/UT-110 VOICE
Rolling type voice
scrambler UT-110
(Version 02)
Non-rolling-type voice
scrambler UT-109
(Version 02)
39
transceiver cannot maintain synchronous mode in rare
cases.
Normally it is best to set this item to "Standard".
Selectable value: Standard (normal operation) or
Continuous (repeater operation)
NOTE: NOTE: NOTE: NOTE: This item is invalid for frequency inversion type
and Non-rolling type.
• Tone Start Timing Tone start timing selects the synchronous tone signal
transmission delay time.
Set the delay time when the other party's transceiver
has power save mode.
Selectable value: OFF (default), 300 ms, 600 ms and
1100 ms.
NOTE: NOTE: NOTE: NOTE: This item is invalid for frequency inversion type
and Non-rolling type.
UT- : The optional UT-109/UT-110 VOICE
SCRAMBLER UNIT.
Inv : Internal voice scrambler is set to Inversion.
Oth : Other voice scrambler unit.
• CodeProgram scrambler codes.
Available codes;
Non-rolling type (UT-109): 1 to 32
Rolling type (UT-110): 1 to 255
*Set the voice scrambler type as Rolling or Non-
rolling in Common screen.
Oth: 1 to 16
Inv: The code setting will be invalid.
NOTE:NOTE:NOTE:NOTE:
- The optional UT-110 or UT-109 VOICE SCRAMBLER
UNIT is required.
- Set the voice scrambler type as Rolling or Non-rolling
in Common screen.
- Set the scrambler group code in the Common screen
in advance.
PSTN
PABX
4 IC-F44G Series (MPT Trunking Model)
4-1 Key Features
What is Trunking?What is Trunking?What is Trunking?What is Trunking?
Conventional CashierConventional CashierConventional CashierConventional CashierWhen each cashier had their own queue and could not
change queues, you could be standing waiting for
service while a neighboring cashier had no customers.
A conventional radio system provides a channel to
each radio. You might be waiting for an available
channel while a neighboring channel is free as the
cashier has its own queue .
Compatible with MPT1327/1343 networksCompatible with MPT1327/1343 networksCompatible with MPT1327/1343 networksCompatible with MPT1327/1343 networks
Dispatcher, individual, group, emergency, priority and
telephone* (PSTN and PABX) calls are available via
voice or status calls.
* Trunking network must be connected to PSTN/PABX.
From small groups to large scale fleets, Icom’s MPT trunking radios
provide reliable communications over MPT trunking networks.
Flexible PC programming allows you to quickly and easily edit/input
settings for individual or entire fleets of radios immediately.
Ease of useEase of useEase of useEase of use
An alphanumeric display, audible tones, 15 call back
memories and backlit keypad provide simple
operation. The handheld and mobile radios provide
Trunked
Radio
Trunked
Radio
40
MPT Like Trunked CashierMPT Like Trunked CashierMPT Like Trunked CashierMPT Like Trunked CashierTrunking provides access to a shared pool of radio
channels through control channel as the reception and
cashiers below. Sharing channels increases the
availability of airtime to all users.
1 2 3
operation. The handheld and mobile radios provide
complimentary operation and functions to each other.
Short Data Message (SDM)Short Data Message (SDM)Short Data Message (SDM)Short Data Message (SDM)
With the DTMF keypad*, short data messages can be
sent directly. 32 status call codes are also available.
*Keypad versions (IC-F44GT) only for handheld radio.
Conventional CTCSS operationConventional CTCSS operationConventional CTCSS operationConventional CTCSS operation
32 conventional channels with CTCSS signalling are
available for operation even in out of service areas.
Other featuresOther featuresOther featuresOther features
• 40 phone memory banks with alphanumeric names
• Optional voice scrambler, UT-109
• 5-digit routing code for abbreviation dialling
• Automatic transmit output power selection
• Built-in audio compander
• Own and 3rd party divert calls
• Flash ROM CPU • Rewritable system messages
• Advanced PC programming capability, and more...
4-2 Operation and Function
GROUP SELECTORGROUP SELECTORGROUP SELECTORGROUP SELECTOR
Rotate to select the pre-
programmed group code
channel.
VOLUME CONTROL [VOL]VOLUME CONTROL [VOL]VOLUME CONTROL [VOL]VOLUME CONTROL [VOL]
Rotate to turn the power
ON/OFF and adjusts the
audio level.
EMERGENCY KEY [RED]EMERGENCY KEY [RED]EMERGENCY KEY [RED]EMERGENCY KEY [RED]
Push and hold for 2 sec.
to start the emergency
call to the specified
number (Emergency call).
“EMRGENCY” is
displayed while pushing
and holding.
ANTENNA CONNECTORANTENNA CONNECTORANTENNA CONNECTORANTENNA CONNECTOR
Connects the supplied
antenna.
CALL BACK KEY [P1]CALL BACK KEY [P1]CALL BACK KEY [P1]CALL BACK KEY [P1]
Push to display the
received call record (call
back memory) that had
not replied.
Push again to return to
PTT SWITCH [PTT]PTT SWITCH [PTT]PTT SWITCH [PTT]PTT SWITCH [PTT]
Push to making a call with the
displayed dialing number.
When selecting a traffic channel for
communication, or conventional
mode, push to transmit.
When an individual call is received,
push to reply the call.
CLEAR (SET MODE) KEY CLEAR (SET MODE) KEY CLEAR (SET MODE) KEY CLEAR (SET MODE) KEY
Push to finish the communication.
Push and hold to enter to the user
set menu.
During some function operation,
push to return to standby condition.
Note: Operation of the function described below may depend on radio programming.
41
[SP]/[MIC] JACK[SP]/[MIC] JACK[SP]/[MIC] JACK[SP]/[MIC] JACK
Connect the optional
speaker-microphone.
HIGH/LOW KEY [P3]HIGH/LOW KEY [P3]HIGH/LOW KEY [P3]HIGH/LOW KEY [P3]
Push to toggle the transmit
output power.
• When automatic power
selection is enabled for
trunking mode operation,
the transmit output power
cannot be selected with
this key.
MODE KEY [P2] MODE KEY [P2] MODE KEY [P2] MODE KEY [P2]
Push to toggle between
conventional and trunking
operation modes.
10101010----KEYPAD (Depending on version)KEYPAD (Depending on version)KEYPAD (Depending on version)KEYPAD (Depending on version)
The keypad allows you to enter digits to:
• Set TX codes
• Set DTMF codes (during transmit)
• Input text message for SDM operation
• Start up with the password
Push again to return to
stand-by condition.
Push and hold for 2.5 sec.
to toggle the call back
mode ON and OFF.
• When the call back
mode is set to ON, the
received call is stored
into record (log), and
the call back message
is send back to the
calling station
automatically.
DESPATCHER KEY [P0] DESPATCHER KEY [P0] DESPATCHER KEY [P0] DESPATCHER KEY [P0]
Push to display dispatcher call conditions.
Push again to display the status code, if
permitted.
Push again to return to stand-by condition.
0UP/DOWN KEYSUP/DOWN KEYSUP/DOWN KEYSUP/DOWN KEYS
Push to select the call memory channel.
Push to select the call back memory channel.
Push to select the status channel.
Push to select the operating channel. (Conventional mode
operation only)
Push to select the setting value or condition during user set mode.
Push to erase the previously entered digit number (functions as
back space key) during dialing number entering from the keypad.
(10-key version only)
FUNCTION DISPLAYFUNCTION DISPLAYFUNCTION DISPLAYFUNCTION DISPLAY
4-2-1 Function Display
1.1.1.1. TRANSMIT INDICATORTRANSMIT INDICATORTRANSMIT INDICATORTRANSMIT INDICATOR
Appears while transmitting.
2.2.2.2. BUSY INDICATORBUSY INDICATORBUSY INDICATORBUSY INDICATOR
Appears while the channel is busy.
3.3.3.3. OVEROVEROVEROVER----FLOW INDICATORFLOW INDICATORFLOW INDICATORFLOW INDICATOR
Appears when the received SDM
including more than 9 characters
is displayed.
4.4.4.4. SIGNAL STRENGTH INDICATORSIGNAL STRENGTH INDICATORSIGNAL STRENGTH INDICATORSIGNAL STRENGTH INDICATOR
Appears when receiving a signal and
9.9.9.9. CALL BACK INDICATORCALL BACK INDICATORCALL BACK INDICATORCALL BACK INDICATOR
Blinks when an individual call is
received.
Appears when individual calls that
the call back operation has not
been performed are available.
Disappears when replies to all
individual calls.
10.10.10.10. PRIMARY NETWORK INDICATORPRIMARY NETWORK INDICATORPRIMARY NETWORK INDICATORPRIMARY NETWORK INDICATOR
Appears when the transceiver is in the
primary network service area.
42
Appears when receiving a signal and
shows the signal strength levels in
4-steps.
• No bars appear and “ ” blinks
when the transceiver is in out-of
service area. For stable
communications, the transceiver
should be in the area that the S-
meter indicator shows the full
scales (3 bars) indication.
5.5.5.5. LOW POWER INDICATORLOW POWER INDICATORLOW POWER INDICATORLOW POWER INDICATOR
Appears when low output power is
selected.
• When the battery power decreases
to a specified level, low power is
selected automatically.
6.6.6.6. AUDIBLE INDICATORAUDIBLE INDICATORAUDIBLE INDICATORAUDIBLE INDICATOR
Appears when the voice
communication can be performed.
7.7.7.7. COMPANDER INDICATORCOMPANDER INDICATORCOMPANDER INDICATORCOMPANDER INDICATOR
Appears when the compander function
is activated.
• The compander function improves
communicating audio quality.
8.8.8.8. SCRAMBLER INDICATORSCRAMBLER INDICATORSCRAMBLER INDICATORSCRAMBLER INDICATOR
Appears when the voice scrambler
function is activated.
primary network service area.
11.11.11.11. KEY LOCK INDICATORKEY LOCK INDICATORKEY LOCK INDICATORKEY LOCK INDICATOR
Appears when the key lock function is
turned ON.
12.12.12.12. BATTERY INDICATORBATTERY INDICATORBATTERY INDICATORBATTERY INDICATOR
Appears or blinks when the battery
power decreases to a specified
level.
13.13.13.13. ALPHANUMERIC DISPLAYALPHANUMERIC DISPLAYALPHANUMERIC DISPLAYALPHANUMERIC DISPLAY
Shows dialing number and received
message, etc.
Note: Appearance of icons on the LCD display depends on the function used and radio programming.
4-2-2 Displaying Messages
IndicationIndicationIndicationIndication DescriptionDescriptionDescriptionDescription
ABORTED Aborted: The call has been aborted. Re-call later.
ALERTING Alerting:
AUTO Auto (RF Power): The automatic transmit output power selection is set.
CALLBACK Call Back: The call is recorded at the calling station. Wait for the reply.
CALLING Calling the station.
CANCELL Canceled: The call/input has been canceled.
Ch Ch##: Channel number ## (Conventional mode)
CLR DOWN Clear Down: The communication connection is disconnected.
CONNECT Connected: The call is succeeded. Communication can be made.
DESPATCH Despatcher: The despatcher number is selected.
DIVERTED Diverted: The call is transferred to another station.
DYN GRP Dynamic Group: A new group number is set.
EMRGENCY Emergency: [Emergency] is pushed and held.
ENGAGED Engaged: The calling station is in busy. Re-call later.
One of the following messages* will be displayed according to the transceiver or system conditions. The displayed
message can be edited with the PC programming.
*Note: Not all of the messages below are possible on some systems.
43
ENGAGED Engaged: The calling station is in busy. Re-call later.
FAILED Failed: The call is failed. Or, the system does not support the calling number.
GRP Group##: Stand-by group code ##
INTER--FL Inter Fleet: The call is received from the different fleet.
INVALID Invalid: The calling number is wrong.
KILLEDKilled: The transceiver operations are inhibited (The “kill” command is received from the base
station.)
LOW Low#: The low transmit output power # is set.
LOW BATT Low : The battery is exhausted and the transceiver power is turned OFF automatically.
NO REPLY No Reply: No reply is received with the call.
OK OK: The call is succeeded.
OVERVOLT Over Voltage: The supplied voltage exceeds the specified input voltage range.
PABX PABX: Receiving a call from PABX.
PASSWORD Password: Enter the password.
Q Queue##: Call back memory number ##.
QUEUED Queued: The call is waiting for turn. Wait for a while.
RINGING Ringing: Ringing the calling bell sound at the calling station.
SYS BUSY System Busy: The system unable to receive a call because of the system in busy. Re-call later.
SYS WIDE System Wide: Receiving a system wide call.
TEL Telephone: Receiving a call from PSTN.
TIMEOUT Timeout: The communication timer has been over.
TIM Timer ##:##: The communicating timer indication.
4-3 Cloning Software CS-F44G (MPT)
Software installationSoftware installationSoftware installationSoftware installation
⑥ The “Choose Destination Location” will appear as
below. Then click [Next>] to install the software to
the destination folder. (e.g. C:\Program
Files\Icom\CS-F44G(MPT))
• Click [Browse...] to select another destination
folder before clicking [Next >], if desired.
System requirementsSystem requirementsSystem requirementsSystem requirements
To use this program, the following hardware and
software are required:
PCPCPCPC
• Microsoft® Windows® 98/98SE/Me/2000/XP is
installed
• With RS-232C serial port (D-sub 9-pin) or USB port
Other itemsOther itemsOther itemsOther items
• OPC-478U/478UC CLONING CABLES (USB type) or OPC-478 CLONING CABLE (RS-232C type)
NOTE:NOTE:NOTE:NOTE:
When using the OPC-478U/478UC, USB type cloning
cables, USB driver installation is necessary. The driver is
supplied with the OPC-478U/478UC. See the OPC-
478U/478UC instruction manual for the installation
details.*The USB driver, supplied with the OPC-478U/478UC, is not
supported for Microsoft®Windows® 98.
Example:
Click
ConfirmClick to select another
destination folder.
Cloning software is used to program various
parameters of the radio like frequency, scanning
etc. Below is the explanation for the basic setup of
this programming software.
44
Software installationSoftware installationSoftware installationSoftware installation
When installing into a Windows ® XP or Windows ® 2000
environment, log in as the administrator.administrator.administrator.administrator.
① Quit all applications when Windows ® is running.
② Insert the CD into the appropriate CD drive.
③ Double-click the “Setup.exe” contained in the CD.
④ The “Welcome to the InstallShield Wizard for
CSF44G(MPT)” will appear as below. Click [Next>].
⑦ After the installation is completed, the “InstallShield
Wizard Complete” will appear as below. Then click
[Finish].
⑧ Eject the CD.
⑨ Program group ‘CS-F44G(MPT)’ appears in the
‘Programs’ folder of the start menu, and ‘CS-
F44G(MPT)’ short cut icon appears on the desktop
screen.
• To uninstall the cloning software, select the
“Control Panel” in the start menu, and click the
“Add or Remove Programs.” Then, select the
program group ‘CS-F44G(MPT)’ and click
[Change/Remove].
Click
Click
Click
Note 1: Icom distributes cloning software by CD or license. Depending on this, some information here may not apply as
written, e.g. ID number.
Note 2: Please see other documents provided by Icom regarding to Microsoft® Windows Vista™.
⑤ The “User Information” will appear as below, then
type your name, your company name and the
product ID number with the following manner. Then
click [Next >].
• ID number: 272505-(6 digit serial number)
• e.g. the serial number on the CD is 000001,
enter “272505-000001” as the ID number.
Cloning Software CS-F44G(MPT)
ConnectionsConnectionsConnectionsConnections
All cloning operations are performed from the computer’s keyboard— the operation required on the transceiver side
is; First, connect the cloning cable as illustrated below. Then, rotate [VOL] to turn power ON.
Screen descriptionScreen descriptionScreen descriptionScreen description
45
①①①① FILE MENU [File]FILE MENU [File]FILE MENU [File]FILE MENU [File]
Used for saving memory channel contents, printing
the pre-programmed information or exiting the
program, etc.
②②②② VIEW MENU [View]VIEW MENU [View]VIEW MENU [View]VIEW MENU [View]
• Selects the displayed font size.
•Turn the tool bar indication ON or OFF.
③③③③ COM PORT MENU [COM Port]COM PORT MENU [COM Port]COM PORT MENU [COM Port]COM PORT MENU [COM Port]
• Click to display the COM port (1 to 4 and More)
setting dialog box.
• Set the transfer speed (Normal or High*).
*OPC-478 does not support ‘High’ speed.
NOTE: ‘NOTE: ‘NOTE: ‘NOTE: ‘Check the following’ dialog box appears when
the COM port is not set correctly.
④④④④ CLONING MENU [Clone]CLONING MENU [Clone]CLONING MENU [Clone]CLONING MENU [Clone]
Click to display the cloning menu and cloning
information dialog box.
⑤⑤⑤⑤ HELP MENU [Help]HELP MENU [Help]HELP MENU [Help]HELP MENU [Help]
Click to display the cloning software revision
information.
⑥⑥⑥⑥ TOOL BARTOOL BARTOOL BARTOOL BAR
Shortcut buttons appear on the tool bar when the
tool bar indication is turned ON in the [View] menu.
⑦⑦⑦⑦ TREE VIEW SCREENTREE VIEW SCREENTREE VIEW SCREENTREE VIEW SCREEN
Click the folder icon which you want to edit.
⑧⑧⑧⑧ CONTENTS LIST SCREENCONTENTS LIST SCREENCONTENTS LIST SCREENCONTENTS LIST SCREEN
Display the contents list (Personality, Common, etc.).
Cloning Software CS-F44G(MPT)
OptionOptionOptionOption
Sets Call memory options such as Despatcher
Number, Direct Despatcher, SDM Number, etc.
EmergencyEmergencyEmergencyEmergency
Sets the Emergency settings such as Emergency
Number.
NetworkNetworkNetworkNetwork
IdentityIdentityIdentityIdentity
Set the Network Identity such as Network Type,
NET/OPID, LA, LZ, Registration Information, etc.
Block FrequenciesBlock FrequenciesBlock FrequenciesBlock Frequencies
Set the first channel number in the network system
given from the system, RX/TX frequencies and tuning
step.
AADAADAADAAD
Set AAD (Acquisition Authorization Data) for using the
transceiver in a specific area of the network.
Timing & ErrorTiming & ErrorTiming & ErrorTiming & Error
Set timer and error conditions.
HuntHuntHuntHunt
• Normal Hunt
Set the hunting channel number for receiving a
control channel signal.
Cloning itemsCloning itemsCloning itemsCloning items
Programming noteProgramming noteProgramming noteProgramming note• Select the optional signalling unit type, if required.• ‘X’ X’ X’ X’ appearing on the lower-right corner on the icon means the edited data in that item is wrong or the
appropriate data is not entered yet. In such a case,
please input the appropriate data in the item.
Tree View screen
46
PersonalityPersonalityPersonalityPersonality
IdentityIdentityIdentityIdentity
Sets each transceiver’s settings such as Fleet
Individual number, Last Individual Number, Last
Group Number, Own Prefix, Own number and RF
Power, etc.
Call RangeCall RangeCall RangeCall Range
Set the Callable Individual Number and Callable
Group Number.
Five Digit LookupFive Digit LookupFive Digit LookupFive Digit Lookup
Sets Five Digit Lookup settings such as Routing
Code, Prefix and Fleet Number, etc.
System MessageSystem MessageSystem MessageSystem Message
Programs a transceiver system message.
Call MemoryCall MemoryCall MemoryCall Memory
Selectable GroupSelectable GroupSelectable GroupSelectable Group
Sets selectable Group number and text, etc.
Memory CallMemory CallMemory CallMemory Call
Sets Dial Number which can be selected via the
Up/Down keys.(up to 24 numbers)
Status CallStatus CallStatus CallStatus Call
Programs a 12-character text for each status.
GroupGroupGroupGroup
Sets the allowable group numbers for group call
receiving.
control channel signal.
• BBS & Comprehensive Hunt
Defines scan channels for background search and
comprehensive hunt.
• Preferential Hunt
CommonCommonCommonCommon
Key & Display AssignKey & Display AssignKey & Display AssignKey & Display Assign
Set the programmable key assign for Trunk mode
and Conventional mode.
Set ModeSet ModeSet ModeSet Mode
User’s setup menu can be set in this menu, such as
Backlight, Ringer, Beep Level, Squelch, etc.
ConventionalConventionalConventionalConventional
Set the channel data for conventional calls.
CommonCommonCommonCommon
Commonly set items such as Clone Comment,
Opening Text, Security, Talk Around, TOT, RSSI, Beep
Frequency, etc.
SignallingSignallingSignallingSignalling
Set the MAP27 contents, Scrambler, CTCSS data.
Character EditorCharacter EditorCharacter EditorCharacter Editor
You can make your original characters and indicate
them on the LCD (Max. 16 characters).
NOTE: NOTE: NOTE: NOTE: The above instructions are for reference only.
Please refer to the HELP file of the cloning software
for the function or setting details.
A-1 Promotional Materials
The following Catalogues are available on the Icom web site.
URL: http://www.icom.co.jp/world/index.html
< Home Page > < Products Page >
47
LMR
Full line brochure
LMR Poster
The following Materials are available upon request through local Icom Distributors
in your region.
IC-F34GT/S
IC-F44GT/S
IC-F43GT/S, IC-F44GT/S
MT Version
A-2 Instruction Manual and Other Materials
The following Instruction Manuals are available on the Icom web site.
URL: http://www.icom.co.jp/world/index.html
< Support Center Page >< Home Page >
48
Programming
Guide
CS-F43G
Technical
Information
BIIS 1200
Instruction
CS-F44G(MPT)
The following Materials are available upon request through local Icom Distributors
in your region.
IC-F34GT/S, IC-F44GT/S
Service Manual
IC-F33G series
Service Manual
IC-F43G series
IC-F43GT/S, IC-F44GT/S
(MT Version)
Instruction
CS-F33G
49