hmc893 (v01.0112) - obsolete · 0 2 4 6 8 10 12 14 vbwctl=vfctl +3v vbwctl=vfctl -3v f20db to...

For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com

Application Support: Phone: 978-250-3343 or [email protected]

Fil

te

rs

- t

un

ab

le -

sM

t

1

HMC893LP5Ev01.0112

FILTER - TUNABLE, BAND PASS SMT4.8 - 9.5 GHz

Functional Diagramthe HMC893lP5e is a MMiC band pass filter which features a user selectable passband frequency. the 3 db filter bandwidth is approximately 6.5%. the 20 db filter bandwidth is approximately 18%. the center frequency can be varied between 4.8 and 9.5 GHz by applying an analog tune voltage between 0 and 14V. this tunable filter can be used as a much smaller alternative to physically large switched filter banks and cavity tuned filters. the HMC893lP5e has excellent microphonics due to the monolithic design, and provides a dynamically adjustable solution in advanced communications applications.

Typical Applications Features

General Description

the HMC892lP5e is ideal for:

• Test & Measurement Equipment

• Military RADAR & EW/ECM

• SATCOM & Space

• Industrial & Medical Equipment

Fast tuning response; 200 ns

Excellent Wideband Rejection; >30 dB

single Chip replacement for Mechanically Tuned Designs

32 lead 5x5 mm sMt Package

Electrical Specifications, TA = +25°C, Vfctl = Vbwctl Unless Otherwise Stated

Parameter Min. typ. Max. units

Fcenter tuning range 4.8 9.5 GHz

3 db bandwidth 6.5 %

Low Side Rejection Frequency (Rejection >20 dB) 0.9*Fcenter GHz

High Side Rejection Frequency (Rejection >20 dB) 1.1*Fcenter GHz

Re-entry Frequency (Rejection <30 dB) 2.7*Fcenter GHz

3 db bandwidth Control (Vbwctl) ±3 %

insertion loss 10 db

Return Loss (2 dB Bandwidth) 7 db

Maximum Input Power for Linear Operation 10 dbm

Frequency Control Voltage (Vfctl) 0 14 V

Source/Sink Current (Ifctl) ±1 ma

bandwidth Control Voltage (Vbwctl) 0 14 V

Source/Sink Current (Ibwctl) ±1 ma

residual Phase noise [1] (1 MHz Offset) -163 dBc/Hz

Fcenter Drift Rate -0.75 MHz/°C

tuning Characteristics [2]

tFULLBAND (0% Vfctl to 90% RF) 200 ns

[1] Optimum residual phase noise performance requires the use of a low noise driver circuit.[2] Tuning speed is dependent on driver circuit. Data measured with a high speed op-amp driver and includes driver slew rate delay.

OBSOLETE

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 Phone: 781-329-4700 • Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D



Fil

te

rs

- t

un

ab

le -

sM

t

2

HMC893LP5Ev01.0112


Broadband Insertion Loss vs. Control Voltages, Vfctl = Vbwctl

Insertion Loss vs. Control Voltages, Vfctl = Vbwctl

Insertion Loss vs. Temperature, Vfctl = Vbwctl = 7V

Broadband Return Loss vs. Control Voltages, Vfctl = Vbwctl

Return Loss vs. Control Voltages, Vfctl = Vbwctl

Return Loss vs. Temperature, Vfctl = Vbwctl = 7V

-70

-60

-50

-40

-30

-20

-10

0

0 5 10 15 20 25 30

0V7V14V

INS

ER

TIO

N L

OS

S (

dB)

FREQUENCY (GHz)

-20

-18

-16

-14

-12

-10

-8

-6

-4

4 5 6 7 8 9 10 11

0V7V14V

INS

ER

TIO

N L

OS

S (

dB)

FREQUENCY (GHz)

-20

-18

-16

-14

-12

-10

-8

-6

-4

4 5 6 7 8 9 10 11

+25C+85C -40C

INS

ER

TIO

N L

OS

S (

dB)

FREQUENCY (GHz)

-30

-25

-20

-15

-10

-5

0

0 5 10 15 20 25 30

S11S22

RE

TU

RN

LO

SS

(dB

)

FREQUENCY (GHz)

14V7V

0V

-30

-25

-20

-15

-10

-5

0

4 5 6 7 8 9 10 11

S11S22

RE

TU

RN

LO

SS

(dB

)

FREQUENCY (GHz)

14V7V0V

-30

-25

-20

-15

-10

-5

0

4 5 6 7 8 9 10 11

+25C+85C -40C

RE

TU

RN

LO

SS

(dB

)

FREQUENCY (GHz)

S22

S11OBSOLETE





Fil

te

rs

- t

un

ab

le -

sM

t

3

HMC893LP5Ev01.0112


Broadband Insertion Loss vs. Vbwctl, Vfctl = 7V

Insertion Loss vs. Vbwctl, Vfctl = 7V

Center Frequency vs. Temperature, Vfctl = Vbwctl

Broadband Return Loss vs. Vbwctl, Vfctl = 7V

Return Loss vs. Vbwctl, Vfctl = 7V

Insertion Loss vs. Temperature, Vfctl = Vbwctl

-80

-70

-60

-50

-40

-30

-20

-10

0

0 5 10 15 20 25 30

Vbwctl=4VVbwctl=7VVbwctl=10V

INS

ER

TIO

N L

OS

S (

dB)

FREQUENCY (GHz)

-20

-18

-16

-14

-12

-10

-8

-6

-4

4 5 6 7 8 9 10 11

Vbwctl=4VVbwctl=7VVbwctl=10V

INS

ER

TIO

N L

OS

S (

dB)

FREQUENCY (GHz)

4

5

6

7

8

9

10

11

0 2 4 6 8 10 12 14

+25C+85C -40CC

EN

TE

R F

RE

QU

EN

CY

(G

Hz)

Vfctl (V)

-35

-30

-25

-20

-15

-10

-5

0

0 5 10 15 20 25 30

S11S22

RE

TU

RN

LO

SS

(dB

)

FREQUENCY (GHz)

Vbwctl=7V

Vbwctl=10V

Vbwctl=4V

-35

-30

-25

-20

-15

-10

-5

0

4 5 6 7 8 9 10 11

S11S22

RE

TU

RN

LO

SS

(dB

)

FREQUENCY (GHz)

Vbwctl=7V

Vbwctl=10V

Vbwctl=4V

-20

-18

-16

-14

-12

-10

-8

-6

-4

-2

0

0 2 4 6 8 10 12 14

+25C+85C -40C

INS

ER

TIO

N L

OS

S (

dB)

Vfctl (V)

OBSOLETE





Fil

te

rs

- t

un

ab

le -

sM

t

4

HMC893LP5Ev01.0112


Maximum Return Loss in a 2 dB Bandwidth vs. Temperature, Vfctl = Vbwctl

Low Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1]

High Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1]

3 dB Bandwidth vs. Temperature, Vfctl = Vbwctl

Tuning Sensitivity vs.Temperature, Vfctl = Vbwctl

[1] rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 db to ƒcenter

Group Delay

4

5

6

7

8

9

0 2 4 6 8 10 12 14

+25C+85C -40C

BA

ND

WID

TH

(%

)

Vfctl (V)

0.85

0.87

0.89

0.91

0.93

0.95

0 2 4 6 8 10 12 14

+25C+85C -40C

F20

dB T

O F

cent

er R

AT

IO

Vfctl (V)

0

100

200

300

400

500

600

700

0 2 4 6 8 10 12 14

+25C+85C -40C

SE

NS

ITIV

ITY

(M

Hz/

V)

Vfctl (V)

-12

-10

-8

-6

-4

-2

0

0 2 4 6 8 10 12 14

+25C+85C -40C

RE

TU

RN

LO

SS

(dB

)

Vfctl (V)

1.05

1.07

1.09

1.11

1.13

1.15

0 2 4 6 8 10 12 14

+25C+85C -40C

F20

dB T

o F

cent

er R

AT

IO

Vfctl (V)

0

0.5

1

1.5

2

3.5 4.5 5.5 6.5 7.5 8.5 9.5 10.5 11.5FREQUENCY (GHz)

GR

OU

P D

ELA

Y (

ns)

0V 7V 14VOBSOLETE





Fil

te

rs

- t

un

ab

le -

sM

t

5

HMC893LP5Ev01.0112


Group Delay vs. Fcenter vs. Temperature 3 dB Bandwidth vs. Bandwidth Control

Insertion Loss vs. Bandwidth ControlLow Side Rejection Ratio vs. Bandwidth Control [1]

High Side Rejection Ratio vs. Bandwidth Control [1]

Maximum Return Loss in a 2 dB Bandwidth vs. Bandwidth Control

[1] rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 db to ƒcenter

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

2

0 2 4 6 8 10 12 14

+ 25C+ 85C- 40C

GR

OU

P D

ELA

Y (

nS)

Vfctl (V)

-25

-20

-15

-10

-5

0

0 2 4 6 8 10 12 14

Vbwctl=VfctlVbwctl=Vfctl+3vVbwctl=Vfctl-3v

INS

ER

TIO

N L

OS

S (

dB)

Vfctl (V)

1

1.05

1.1

1.15

1.2

1.25

0 2 4 6 8 10 12 14


F20

dB T

O F

cent

er R

AT

IO

Vfctl (V)

0

2

4

6

8

10

12

0 2 4 6 8 10 12 14


BA

ND

WID

TH

(%

)

Vfctl (V)

0.8

0.85

0.9

0.95

1

0 2 4 6 8 10 12 14

Vbwctl=VfctlVbwctl=Vfctl +3vVbwctl=Vfctl -3v

F20

dB T

O F

cent

er R

AT

IO

Vfctl (V)

-10

-8

-6

-4

-2

0

0 2 4 6 8 10 12 14


RE

TU

RN

LO

SS

(dB

)

Vfctl (V)

OBSOLETE





Fil

te

rs

- t

un

ab

le -

sM

t

6

HMC893LP5Ev01.0112


Residual Phase NoiseVfctl = Vbwctl

Input IP3 vs. Power InputVfctl = Vbwctl

ELECTROSTATIC SENSITIVE DEVICEOBSERVE HANDLING PRECAUTIONS

Absolute Maximum Ratings Reliability InformationFrequency Control Voltage (Vfctl) -0.5 to +15V

Bandwidth Control Voltage (Vbwctl) -0.5 to +15V

rF Power input 26 dbm

storage temperature -65 to +150 °C

ESD Rating (HBM) Class 1b

Junction temperature to Maintain 1 Million Hour MttF

150 °C

nominal Junction temperature (t= 85 °C and Pin = 10 dBm)

90 °C

Operating Temperature -40 to +85 °C

10

15

20

25

30

35

4.6 5.1 5.6 6.1 6.6 7.1 7.6 8.1 8.6 9.1 9.6 10.1

Pin = 0 dBmPin = 5 dBmPin = 10 dBmPin = 15 dBmPin = 20 dBm

IP3

(dB

m)

FREQUENCY (GHz)

-170

-160

-150

-140

-130

-120

1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7

0V7V13V

RE

SID

UA

L P

HA

SE

NO

ISE

(dB

c/H

z)

OFFSET FREQUENCY (Hz)

OBSOLETE





Fil

te

rs

- t

un

ab

le -

sM

t

7

HMC893LP5Ev01.0112


Outline Drawing

NOTES:1. LEADFRAME MATERIAL: COPPER ALLOY2. DIMENSIONS ARE IN INCHES [MILLIMETERS]3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.4. Pin burr lenGtH sHall be 0.15mm MaXiMuM. Pin burr HeiGHt sHall be 0.05mm MaXiMuM.5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND.7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN.

Part number Package body Material lead Finish Msl rating Package Marking [1]

HMC893lP5e roHs-compliant low stress injection Molded Plastic 100% matte sn Msl1 [2] H893XXXX

[1] 4-Digit lot number XXXX[2] Max peak reflow temperature of 260 °C

Package Information

OBSOLETE





Fil

te

rs

- t

un

ab

le -

sM

t

8

HMC893LP5Ev01.0112


Pin Descriptions

Application Circuit

Pin number Function Description interface schematic

1 - 4, 7 - 11, 1315 - 18, 21 - 32

N/Cthe pins are not connected internally; however, all data

shown herein was measured with these pins connected to RF/DC ground externally.

5, 20 GNDthese pins and exposed paddle

must be connected to RF/DC ground.

6 rFinThis pin is DC coupled and matched to 50 Ohms. external voltage must not be applied to this pin.

12 Vfctl Center frequency control voltage.

14 Vbwctl bandwidth control voltage.

19 RFOUTThis pin is DC coupled and matched to 50 Ohms. external voltage must not be applied to this pin.

OBSOLETE





Fil

te

rs

- t

un

ab

le -

sM

t

9

HMC893LP5Ev01.0112


Evaluation PCB

the circuit board used in the application should use rF circuit design techniques. signal lines should have 50 Ohms impedance while the package ground leads and exposed paddle should be con-nected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation circuit board shown is available from Hittite upon request.

List of Materials for Evaluation PCB 128531 [1]

item Description

J1, J2 sMa - sri

J3, J4 sMa - Johnson

C1, C2 100 pF Capacitor, 0402 Pkg.

u1 HMC893lP5e Filter - tunable

PCb [2] 127338 evaluation PCb

[1] reference this number when ordering complete evaluation PCb

[2] Circuit board Material: arlon 25Fr or rogers 4350

OBSOLETE





Fil

te

rs

- t

un

ab

le -

sM

t

10

HMC893LP5Ev01.0112


Notes:

OBSOLETE



hmc893 (v01.0112) - obsolete · 0 2 4 6 8 10 12 14 vbwctl=vfctl +3v vbwctl=vfctl -3v f20db to...

Documents