high performance vertical turning center - doosan · pdf file02 the vertical turning center is...
TRANSCRIPT
High Performance Vertical Turning Center
02
The vertical turning center is designed for long term accuracy,
heavy duty cutting and to minimize floor space.
Its powerful spindle drives, meehanite casting and
integral box guide way provide unsurpassed rigidity.
03
New standard for unsurpassed high productivity,high speed and high precision
04
Robust Bed Construction
In order to assure heavy duty machining and optimized
chip flow, the machine base body is designed and
streamlined. Its small foot print help you systemizing your
manufacturing plan plot in your factory.
Robust Column Construction
The wide hardened and ground box ways reduce vibration promoting better tool life and
surface finishes. The box ways are turcite coated which allows for 787 ipm rapid traverse
rates. The Balanced Counter Weight located inside the column, neutralizes the gravity effect
on the Vertical slide. It will also conserve electricity and prevent Turret Drop while in
Emergency stop or Power failure. All axis Slides are Induction Hardened and Ground HrC 55
Hardness. Long-term Accuracies are very basic requirements on Doosan Infracore products.
3 adjustable Gibs on each Axis slide are provided to maintain original accuracy.
3Gibs Suport on each for longterm and easy to maintain accuracy
High Performance Spindle & Turret
The spindle is supported by a
double row of tapered roller
bearings in the Top and Bottom of
the spindle while angular thrust
bearings provide tremendous
radial load capability. The Cartridge
Spindle is axial symmetric
construction, which provides very
stable accuracy all day-long even
when the spindle is heated up by
continuous operation.
V12 Turret is ground finish for
Zero accuracy. Turret has large
Three piece curvic couplings.
of clamping force so high
accuracy and heavy-duty
cutting can be achieved. The
12 station turret holds ID or
OD tools.
Basic Mechanism
05
Safety Cover
12 mm Poly carvonate
(0.4 inch)
double steel cover
Easy Operation
The swing arm on the Main Operation panel is a
userfriendly feature to minimize the distance
from Part to operator’s Panel during setup.
Narrow Vertical panel is space saving design.
The handy Sub Operation Panel beside Door for
each spindle has Cycle start, Feed hold,
Emergency stop, Door Open/close switches.
Chip Disposal
Flexible Chip ConveyorRight / Left (Rear / Side)
Over head Coolant for chuck
Chip air blow
Bed wash coolant
Chip ConveyorLeft
Chip Conveyor Rear Chip Conveyor Rear
Chip ConveyorRight
Accessories
Manual tool setterRemovable type, Renishaw
Gear boxPUMA VT900 / VT1100
Auto doorPneumatic cylinder
06
VT450 / VT450M / VT450-2SP / VT450M-2SP
Main Specification
Main Spindle Power-torque Diagram
PUMA VT450
Max. spindle speed
2500 r/min
Motor (30 min)
22 kW (29.5 Hp)
Travels (X / Z axis) mm (inch) 240 / 450 (9.4 / 17.7)
Chuck size mm (inch) 305 (12.0)
Max. Spindle speed r/min 2500
Spindle motor (Cont. / 15min.) kW (Hp) 18.5 / 22 (24.8 / 29.5)
Rapid Traverse (X / Z axis) m/min (ipm) 20 / 20 (787.4 / 787.4)
Turret index time s 1.6 (PUMA VT450)
No. of tool station stations 12
Std. M/C dimension (L x W x H) mm (inch) 1445 x 2491 x 3009(56.9 x 98.1 x 118.5)*
Machine weight kg (lb) 6200 kg (13668.5 lb)*
* : PUMA VT450 / VT450M
30min Power
High Gear 22kW (29.5)Continuous Power
30min Torque
200 (147.6)
180 (132.8)
160 (118.1)
140 (103.3)
120 (88.6)
100 (73.8)
80 (59.0)
60 (44.3)
40 (29.5)
20 (14.8)
0
30 (40.2)
25 ( 3.5)
20 (26.8)
15 (20.1)
10 (13.4)
5 (6.7)
Torque : N. W (Hp)k : rewoP (ft-lb) m
High Gear 26kW (34.9)
High Gear 26kW (34.9)
High Gear 22kW (29.5)Continuous Torque
30min PowerLow Gear 26kW (34.9) Low Gear 26kW (34.9)
Low Gear 22kW (29.5)
Low Gear 22kW (29.5)Continuous Torque
Continuous Power
Spindle Speed (r/min)
0 24002200200018001600140012001000200 400 600 8002500
PUMA VT450 with ZF GearboxPUMA VT450 with ZF Gearbox
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400
1568 (1157.2)
1372 (1012.5)
1176 (867.9)
980 (723.2)
784 (578.6)
588 (433.9)
392 (289.3)
196 (144.6)
0
30 (40.2)
25 (33.5)
20 (26.8)
15 (20.1)
10 (13.4)
5 (6.7)
0
Spindle Speed (r/min)
Torque : N. )pH( Wk : rewoP)bl-tf( m PUMA VT450
Low 22 kW (29.5 Hp) 15 min Torque
Low 22 kW (29.5 Hp) 15 min Power
Low 13 kW (17.4 Hp) Continuous Power
High 22 kW (29.5 Hp) 30 min Power
High 22 kW (29.5 Hp) 30 min Torque
High 18.5 kW (24.8 Hp) Continuous Torque
High 18.5 kW (24.8 Hp) Continuous Power
Low 13 kW (17.4 Hp) Continuous Torque
07
VT750 / VT750M / VT750-2SP / VT750M-2SP
Main Specification
Main Spindle Power-torque Diagram
PUMA VT750
Max. spindle speed
2000 r/min
Motor(30 min)
30 kW (40.2 Hp)
Travels (X / Z axis) mm (inch) 385 / 760 (15.2 / 29.9)
Chuck size mm (inch) 381 (15.0)
Max. Spindle speed r/min 2000
Spindle motor (Cont. / 30min.) kW (Hp) 22 / 30 (29.5 / 40.2)
Rapid Traverse (X / Z axis) m/min (ipm) 20 / 20 (787.4)
Turret index time s 1.8 (PUMA VT750)
No. of tool station stations 12
Std. M/C dimension (L x W x H) mm (inch) 1850 x 2785 x 3450*(72.8 x 109.6 x 135.8)
Machine weight kg (lb) 9700 (21384.5)*
* : PUMA VT750 / VT750M
Spindle Speed (r/min)
Torque : N. )pH(Wk:rewoP)bl-tf(m PUMA VT750 with ZF Gearbox
2940 (2169.7)
2646 (1952.7)
2352 (1735.8)
2058 (1518.8)
1764 (1301.8)
1470 (1084.9)
1176 (867.9)
882 (650.9)
588 (433.9)
294 (217.0)
0
50 (67.1)
45 (60.3)
40 (53.6)
35 (46.9)
30 (40.2)
25 (33.5)
20 (26.8)
15 (20.1)
10 (13.4)
5 (6.7)
0
Low Gear 37 kW (49.6 Hp) 30 min Torque Low Gear 37 kW (49.6 Hp)
30 min TorqueHigh Gear 37 kW (49.6 Hp) 30 min Power
High Gear 30 kW (40.2 Hp) Continuous Power
High Gear 37 kW (49.6 Hp) 30 min Torque
High Gear 30 kW (40.2 Hp) Continuous Torque
Low Gear 30 kW (40.2 Hp) Continuous Power
Low Gear 30 kW (40.2 Hp) Continuous Torque
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Spindle Speed (r/min)
Torque : N. )pH( Wk : rewoP)bl-tf( m PUMA VT750
1764 (1301.8)
1568 (1157.2)
1372 (1012.5)
1176 (867.9)
980 (723.2)
784 (578.6)
588 (433.9)
392 (289.3)
196 (144.6)
0
40 (53.6)
35 (46.9)
30 (40.2)
25 (33.5)
20 (26.8)
15 (20.1)
10 (13.4)
5 (6.7)
0
Low 30 kW (40.2 Hp) 30 min Torque
Low 30 kW (40.2 Hp) 30 min Power
High 30 kW (40.2 Hp) 30 min Power
High 22 kW (29.5 Hp) Continuous Power
High 30 kW (40.2 Hp) 30 min Torque
High 22 kW (29.5 Hp) Continuous Torque
Low 22 kW (29.5 Hp) Continuous Power
Low 30 kW (40.2 Hp) Continuous Torque
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Working Range
750 (29.5)
760(29.9)
750 (29.5)
610 (24.0)
500(19.7)
160(6.3)
Max. working range
unit : mm (inch)
Interference area750 (29.5)
760(29.9)
750 (29.5)
610 (24.0)
500(19.7)
160(6.3)
If working length 160mm (6.3 inch)excess, interference area
08
VT900 / VT900M / VT900-2SP / VT900M-2SP
Main Specification Working Range
Main Spindle Power-torque Diagram
PUMA VT900
Max. spindle speed
1800 r/min
Motor(30 min)
45 kW (60.3 Hp)
Travels (X / Z axis) mm (inch) 470 / 850 (18.5 / 33.5)
Chuck size mm (inch) 610 (24.0)
Max. Spindle speed r/min 1800
Spindle motor (Cont. / 15min.) kW (Hp) 37 / 45
Rapid Traverse (X / Z axis) m/min (ipm) 20 / 20 (787.4 / 787.4)
Turret index time s 2.0 (PUMA VT900)
No. of tool station stations 12
Std. M/C dimension (L x W x H) mm (inch) 2130 x 3050 x 3621*(83.9 x 120.1 x 142.6)
Machine weight kg (lb) 12500 (2755.7)*
* : PUMA VT900 / VT900M
5 155 305 455 605 755 905 1055 1205 1355 1505 1655 1800
4900 (3616.2)
4508 (3326.9)
4116 (3037.6)
3724 (2748.3)
3332 (2459.0)
2940 (2169.7)
2548 (1880.4)
2156 (1591.1)
1764 (1301.8)
1372 (1012.5)
980 (723.2)
588 (433.9)
196 (144.6)0
4446
50 (67.1)
45 (60.3)
40 (53.6)
35 (46.9)
30 (40.2)
25 (33.5)
20 (26.8)
15 (20.1)
10 (13.4)
5 (6.7)
0
Spindle Speed (r/min)
Torque : N. )pH( Wk : rewoP)bl-tf( m PUMA VT900 with ZF Gearbox
Low Gear 45 kW (60.3 Hp)30 min Torque
Low Gear 45 kW (60.3 Hp) 30 min Power
High Gear 45 kW (60.3 Hp) 30 min Power
High Gear 37 kW (49.6 Hp) Continuous Power
High Gear 45 kW (60.3 Hp) 30 min Torque
High Gear 37 kW (49.6 Hp) Continuous Torque
Low Gear 37 kW (49.6 Hp) Continuous Power
Low Gear 37 kW (49.6 Hp) Continuous Torque
unit : mm (inch)
900 (35.4)
850(33.5)
900 (35.4)
700 (27.6)
660(26.0)
190(7.5)
Max. working range
Interference area
If working length 190mm (7.5 inch)excess, interference area
09
VT1100 / VT1100M
Main Specification Working Range
Main Spindle Power-torque Diagram
PUMA VT1100
Max. spindle speed
850 r/min
Motor(30 min)
60 kW (80.5 Hp)
Travels (X / Z axis) mm (inch) 580 / 1000 (22.8 / 39.4)
Chuck size mm (inch) 800 (31.5)
Max. Spindle speed r/min 850
Spindle motor (Cont./30min./10min.) kW (Hp) 45 / 55 / 60 (60.3 / 73.8 / 80.5)
Rapid Traverse (X / Z axis) m/min (ipm) 20 / 20 (787.4 / 787.4)
Turret index time s 2.2
No. of tool station stations 12
Std. M/C dimension (L x W x H) mm (inch) 2850 x 3305 x 4012(112.2 x 130.1 x 158.0)
Machine weight kg (lb) 22000 (48501.0)
5 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850
63896860 (5062.7)
5880 (4339.4)
4900 (3616.2)
3920 (2893.0)
2940 (2169.7)
1960 (1446.5)
980 (723.2)
0
70 (93.9)
60 (80.5)
50 (67.1)
40 (53.6)
30 (40.2)
20 (26.8)
10 (13.4)
0
Spindle Speed (r/min)
Torque : N.m (ft-lb) Power : kW (Hp)PUMA VT1100 with ZF Gearbox
Low Gear 55 kW (73.8 Hp) 30 min TorqueLow Gear 60 kW (80.5 Hp) 10 min Power
Low Gear 55 kW (73.8 Hp) 30 min Power
High Gear 60 kW (80.5 Hp) 10 min Power
High Gear 55 kW (73.8 Hp) 30 min Power
High Gear 45 kW (60.3 Hp) Continuous Power
High Gear 55 kW (73.8 Hp) 30 min Torque
Low Gear 45 kW (60.3 Hp) Continuous Torque
Low Gear 45 kW (60.3 Hp) Continuous Power
High Gear 45 kW (60.3 Hp) Continuous Torque
unit : mm (inch)
1100 (43.3)
1000(39.4)
1100 (43.3)
1000 (39.4)
760(29.9)
240(9.4)
Max. working range
Interference area
If working length 240mm (9.4 inch)excess, interference area
10
Tooling System
Unit: mm (inch)
PUMA VT450 / VT450-2SP
PUMA VT450M / VT450M-2SP
O.D Tool□25 RL
Facing Tool□25 RL
Taper DrillMT. No.1,2,3,4
Face Holder□25 RL
Boring Holderø50
U-Drill Capø50
U-Drill Sleeve
Boring Sleeve
U-Drillø16 ø20 ø35 ø40
Boring Barø12 ø16 ø20ø25 ø32 ø40
Boring Bar
ø50 ø50
ø50
ø50
12 Station Turret
Boring Sleeveø50 (2.0) - ø12 (0.5)ø50 (2.0) - ø16 (0.6)ø50 (2.0) - ø20 (0.8)ø50 (2.0) - ø25 (1.0)ø50 (2.0) - ø32 (1.3)ø50 (2.0) - ø40 (1.6)
U-Drill Sleeveø50 (2.0) - ø20 (0.8)ø50 (2.0) - ø25 (1.0)ø50 (2.0) - ø32 (1.3)ø50 (2.0) - ø32 (1.3)
Drill Socket ø50 (2.0) - MT. 1ø50 (2.0) - MT. 2ø50 (2.0) - MT. 3ø50 (2.0) - MT. 4
O.D Tool□25
O.D Tool Holder□25
Face Tool Holder□25
U-Drill Cap(BMT 65)
I.D Tool Holderø40
Facing Tool□25
Boring Barø10 ø12ø16 ø20ø25 ø32
U-Drillø20ø25ø32
Boring BarSleeves
Strightmilling unit
Collet Adapter
Milling ArborAdapter
Weldon Adapter
Angularmilling unit
Plug
U-DrillSleeves
12st Turret(BMT 65P/ER32)
ø40
ø40
Note) Above tooling system is our recommendation. Depending on export condition, the standard tooling packed with the machine can be different.
Boring Sleeveø10 (0.4) - ø40 (1.6)ø12 (0.5) - ø40 (1.6)ø16 (0.6) - ø40 (1.6)ø20 (0.8) - ø40 (1.6)ø25 (1.0) - ø40 (1.6)ø32 (1.3) - ø40 (1.6)
U-Drill Sleeveø20 (0.8) - ø40 (1.6)ø32 (1.3) - ø40 (1.6)ø32 (1.3) - ø60 (2.4)
Drill Socket
ø50
11
Unit: mm (inch)
PUMA VT750 / VT750-2SP
PUMA VT750M / VT750M-2SP
O.D Tool□25 RL
O.D Holder□25 RL
Facing Tool□25 RL
Taper DrillMT. No.1,2,3,4
Face Holder□25 RL
Boring Holderø50
U-Drill Capø50
U-Drill Sleeve
Boring Sleeve
U-Drillø20 ø25 ø32 ø40
Boring Barø12 ø16 ø20ø25 ø32 ø40
Boring Bar
ø50 ø50
ø50
ø50
12 Station Turret
O.D Tool□25
O.D Tool Holder□25
Face Tool Holder□25
U-Drill Cap(BMT 75)
I.D Tool Holderø60
Facing Tool□25
Boring Barø16 ø20ø25 ø32ø40 ø50
U-Drillø25 ø32ø40 ø50
Boring BarSleeves
Strightmilling unit
Collet Adapter
Milling ArborAdapter
Weldon Adapter
Angularmilling unit
Plug
U-DrillSleeves
12st Turret(BMT 75P/ER40)
ø60
ø60
Note) Above tooling system is our recommendation. Depending on export condition, the standard tooling packed with the machine can be different.
Boring Sleeveø16 (0.6) - ø60 (2.4)ø20 (0.8) - ø60 (2.4)ø25 (1.0) - ø60 (2.4)ø32 (1.3) - ø60 (2.4)ø40 (1.6) - ø60 (2.4)ø50 (2.0) - ø60 (2.4)
U-Drill Sleeveø25 (1.0) - ø60 (2.4)ø32 (1.3) - ø60 (2.4)ø40 (1.6) - ø60 (2.4)ø50 (2.0) - ø60 (2.4)
Boring Sleeveø50 (2.0) - ø12 (0.5)ø50 (2.0) - ø16 (0.6)ø50 (2.0) - ø20 (0.8)ø50 (2.0) - ø25 (1.0)ø50 (2.0) - ø32 (1.3)ø50 (2.0) - ø40 (1.6)
U-Drill Sleeveø50 (2.0) - ø20 (0.8)ø50 (2.0) - ø25 (1.0)ø50 (2.0) - ø32 (1.3)ø50 (2.0) - ø32 (1.3)
Drill Socket ø50 (2.0) - MT. 1ø50 (2.0) - MT. 2ø50 (2.0) - MT. 3ø50 (2.0) - MT. 4
Drill Socket
ø50
12
Tooling System
Unit: mm (inch)
PUMA VT900 / VT900-2SP
PUMA VT900M / VT900M-2SP
O.D Tool□32
O.D Tool Holder□32
Face Tool Holder□32
U-Drill Cap(BMT 85)
I.D Tool Holderø80
Facing Tool□32
Boring Barø20 ø25ø32 ø40ø50 ø60
U-Drillø25 ø32ø40 ø50
Boring BarSleeves
Strightmilling unit
Collet Adapter
Milling ArborAdapter
Weldon Adapter
Angularmilling unit
Plug
U-DrillSleeves
12st Turret(BMT 85P/ER50)
ø80
ø80
Note) Above tooling system is our recommendation. Depending on export condition, the standard tooling packed with the machine can be different.
O.D Tool□32 RL
Facing Tool□32 RL
Profile Tool□32 RL
Taper DrillMT. No.3,4,5
O.D Holder□32 RL
Face Holder□32 RL
U-Drill Capø80
I.D Tool Holderø80U-Drill Sleeve
Boring Sleeve
U-Drillø32 ø40 ø50 ø60
Boring Barø20 ø25 ø32ø40 ø50 ø60
Boring Bar
ø80
ø80
ø80
12 Station Turret
Boring Sleeveø80 (3.1) - ø20 (0.8)ø80 (3.1) - ø25 (1.0)ø80 (3.1) - ø32 (1.3)ø80 (3.1) - ø40 (1.6)ø80 (3.1) - ø50 (2.0)ø80 (3.1) - ø60 (2.4)
U-Drill Sleeveø80 (3.1) - ø32 (1.3)ø80 (3.1) - ø40 (1.6)ø80 (3.1) - ø50 (2.0)ø80 (3.1) - ø60 (2.4)
Drill Socket ø80 (3.1) - MT. 3ø80 (3.1) - MT. 4ø80 (3.1) - MT. 5
Boring Sleeveø20 (0.8) - ø80 (3.1)ø25 (1.0) - ø80 (3.1)ø32 (1.3) - ø80 (3.1)ø40 (1.6) - ø80 (3.1)ø50 (2.0) - ø80 (3.1)ø60 (2.4) - ø80 (3.1)
U-Drill Sleeveø32 (1.3) - ø80 (3.1)ø40 (1.6)- ø80 (3.1)ø50 (2.0) - ø80 (3.1)ø60 (2.4) - ø80 (3.1)
Drill Socket
ø80
13
O.D Tool□32
O.D Tool Holder□32
Face Tool Holder□32
U-Drill Cap(BMT 85)
I.D Tool Holderø80
Facing Tool□32
Boring Barø20 ø25ø32 ø40ø50 ø60
U-Drillø25 ø32ø40 ø50
Boring BarSleeves
Strightmilling unit
Collet Adapter
Milling ArborAdapter
Weldon Adapter
Angularmilling unit
Plug
U-DrillSleeves
12st Turret(BMT 85P/ER50)
ø80
ø80
Unit: mm (inch)
PUMA VT1100
PUMA VT1100M
O.D Tool□32 RL
Facing Tool□32 RL
Profile Tool□32 RL
Taper DrillMT. No.3,4,5
O.D Holder□32 RL
Face Holder□32 RL
U-Drill Capø80
I.D Tool Holderø80U-Drill Sleeve
Boring Sleeve
U-Drillø32 ø40 ø50 ø60
Boring Barø20 ø25 ø32ø40 ø50 ø60
Boring Bar
ø80
ø80
ø80
12 Station Turret
Note) Above tooling system is our recommendation. Depending on export condition, the standard tooling packed with the machine can be different.
Boring Sleeveø80 (3.1) - ø20 (0.8)ø80 (3.1) - ø25 (1.0)ø80 (3.1) - ø32 (1.3)ø80 (3.1) - ø40 (1.6)ø80 (3.1) - ø50 (2.0)ø80 (3.1) - ø60 (2.4)
U-Drill Sleeveø80 (3.1) - ø32 (1.3)ø80 (3.1) - ø40 (1.6)ø80 (3.1) - ø50 (2.0)ø80 (3.1) - ø60 (2.4)
Drill Socket ø80 (3.1) - MT. 3ø80 (3.1) - MT. 4ø80 (3.1) - MT. 5
Boring Sleeveø20 (0.8) - ø80 (3.1)ø25 (1.0) - ø80 (3.1)ø32 (1.3) - ø80 (3.1)ø40 (1.6) - ø80 (3.1)ø50 (2.0) - ø80 (3.1)ø60 (2.4) - ø80 (3.1)
U-Drill Sleeveø32 (1.3) - ø80 (3.1)ø40 (1.6)- ø80 (3.1)ø50 (2.0) - ø80 (3.1)ø60 (2.4) - ø80 (3.1)
Drill Socket
ø80
14
Tool Interference Diagram
Unit: mm (inch)
PUMA VT450 / VT450-2SP
PUMA VT750 / VT750-2SP
PUMA VT450M / VT450M-2SP
PUMA VT750M / VT750M-2SP
ø450 (17.7)
ø290 (11.4)
ø254 (10.0)
ø240 (9.4)
15 (0.6) 225 (8.9)40(1.6) 245 (9.6)
285 (11.2)240 (9.4)
ø680 (26.8)
ø530 (20.9)
ø660 (26.0)
ø357 (14.1)
ø358 (14.1)
ø317 (12.5)
ø800
(31.
5)
ø720 (28.3)
ø800
(31.
5) (M
ax. s
wing)
ø308(12.1)
ø820(32.3)
ø317 (12.5)
ø710 (28.0)
ø68
0 (2
6.8)
385 (15.2) 110 (4.3)
(X-axis Travel)
385 (15.2) 355 (14.0) 245 (9.6) 117 (4.6)
(X-axis Travel)
25 (1.0)
110 (4.3)110 (4.3)25 (1.0) 7 (0.3)245 (9.6)
35(1.4)
75(3.0)
ø245 (9.6)
ø556 (21.9)
ø271 (10.7)ø245 (9.6)
ø256 (10.1)
ø680 (26.8)
ø236 (9.3)
15 (0.6) 225 (8.9)
240 (9.4)
(X-axis Travel)
285 (11.2)
35(1.4) 250 (9.8)
213 (8.4)37(1.5)
ø450 (17.7)
ø269 (10.6)
ø740 (29.1)
ø312 (12.3)
ø586 (23.1)
ø286 (11.3)
ø820 (32.3)
ø294(11.6)
ø297 (11.7)
15 (0.6)40(1.6)370 (14.6)
50(2.0) 255 (10.0)
305 (12.0)
30(1.2)
90 (3.5)
7(0
.3)
70(2
.8)
345 (13.6)385 (15.2)
(X-axis Travel)
15
Unit: mm (inch)
PUMA VT900 / VT900-2SP
PUMA VT1100
PUMA VT900M / VT900M-2SP
PUMA VT1100M
ø900 (35.4)
ø680 (26.8)
ø317 (12.5)
ø308 (12.1)
ø371 (14.6)
ø316 (12.4)
ø312 (12.3)
ø920 (36.2)
ø313 (12.3)80(3.1) 250 (9.8)
330 (13.0)40(1.6)20 (0.8) 450 (17.7)
370 (14.6)470 (18.5)(X-axis Travel)
580 (22.8)
25 (1.0)
ø921 (36.3)
ø1100 (43.3)
ø1200 (47.2)
ø502 (19.8)
ø437 (17.2)
ø921 (36.3)
ø440 (17.3)
ø440 (17.3)
500 (19.7)
350 (13.8)110(4.3)
40 (1.6)
20 (0.8) 450 (17.7) 310 (12.2)40(1.6) 350 (13.8)
45(1.8) 265 (10.4)
ø310.8 (12.2)
ø284 (11.2)
ø282 (11.1)
ø620 (24.4)
ø282 (11.1)
ø282 (11.1)ø900 (35.4) ø920 (36.2)
470 (18.5)(X-axis Travel)
350 (13.8)110(4.3)
40 (1.6)
500 (19.7)580 (22.8)
25 (1.0)
ø440 (17.3)
ø418 (16.5)
ø440 (17.3)
ø923 (36.3)
ø1100 (43.3)
ø925 (36.4)
ø1200 (47.2)
ø418 (16.5)
ø485 (19.1)
16
Working Range
Unit: mm (inch)
PUMA VT450 / VT450-2SP
7(0
.3)
450
(17.
7)(Z
-axi
s Tr
avel
)
460.
9 (1
8.1)
150
(5.9
)
100
(3.9
)13
2.9
(5.2
)40
(1.6
)40
(1.6
)
132.
9 (5.
2)
150
(5.9
)45
0 (1
7.7)
(Z-a
xis
Trav
el)
450
(17.
7) (Z
-axi
s Tr
avel
)
12 inch 12 inch
122
(4.8
)
125.
9(5
.0)
PUMA VT450M / VT450M-2SP
52 (2.0
)45
0 (1
7.7)
(Z-a
xis
Trav
el)
450
(17.
7)(Z
-axi
s Tr
avel
)
451.
4 (1
7.8)
127
(5.0
)
21 (0.8
)12
7 (5
.0)
106
(4.2
)16 (0.6
)102.4
(4.0)
100
(3.9
)10
0(3
.9)
28 (1.1
)
450
(17.
7) (Z
-axi
s Tr
avel
)
12 inch
15 (0.6)
240 (9.4)(X-axis Travel)
12 inch
122
(4.8
)
71.4
(2.8
)
15 inch
255 (10.0) 155 (6.1)
15 inch
15 (0.6)
385 (15.2)(X-axis Travel)
760
(29.
9) (Z
-axi
s Tr
avel
)
760
(29.
9) (Z
-axi
s Tr
avel
)14
7.5 (5
.8)
24 (0.9
)
150
(5.9
)
57 (2.2
)77
5.5
(30.
5)11
5(4
.5)
132
(5.2
)
PUMA VT750M / VT750M-2SP
15 inch
25 (1.0)
50 (2.0)(X-axis Travel)
(X-axis Travel)
35 (1.4)
35 (1.4)385 (15.2)
385 (15.2)
75 (3.0)
15 inch
32(1.3)
85(3.3)
245 (9.6)
110 (4.3)
152.5 (6.0)
760
(29.
9)37 (1.5
)
200
(7.9
)76
0 (2
9.9)
80 (3.1
)
61 (2.4)
734
(28.
9)13
2 (5.
2)
760
(29.
9) (Z
-axi
s Tr
avel
)16
7(6
.6)
35 (1.4)
200
(7.9
)
110
(4.3
)
132
(5.2
)
37 (1
.5)
PUMA VT750 / VT750-2SP
17
Unit: mm (inch)
PUMA VT900 / VT900-2SP
850
(33.
5)
850
(33.
5)14
7 (5
.8)
43 (1.7
)
50 (2
.0)
800
(31.
5)50
(2.0
)
43 (1
.7)
147
(5.8
)
24 inch
20 (0.8)
470 (18.5)
80 (3.1)
120 (4.7) 250 (9.8) 250 (9.8)
120 (4.7)
128 (5.0)
850
(33.
5)
43 (1
.7)
200
(7.9
)
125
(4.9
)43 (1.
7)14
7 (5
.8)
24 inch
80 (3.1) 130 (5.1)
120 (4.7) 250 (9.8) 250 (9.8) 188 (7.4)
PUMA VT900M / VT900M-2SP
850
(33.
5) (Z
-axi
s Tr
avel
)13
(0.5
)
190
(7.5
)
24 inch
20 (0.8)
470 (18.5) (X-axis Travel)
850
(33.
5) (Z
-axi
s Tr
avel
)15
5 (6
.1)
60 (2.4
)140
(5.5
)85
8 (3
3.8)
147
(5.8
)
24 inch
265 (10.4) 195 (7.7)
18
Working Range
Unit: mm (inch)
PUMA VT1100
32 inch
150
(5.9
)10
00 (3
9.4)
300
(11.
8)
150
(5.9
)30
0 (1
1.8)
40 (1.6)
40 (1
.6)
8 (0
.3)
580 (22.8)
40 (1.6)
40(1.6)
25(1.0)
110(4.3)
110 (4.3)
151 (5.9)150 (5.9) 350 (13.8) 350 (13.8)
500 (19.7)
228 (9.0)
158 (6.2)
501 (19.7) 70(2.8)
110 (4.3)
150 (5.9)
151 (5.9)
150 (5.9)
142 (5.6)8 (0.3)
32 (1.3)
221 (8.7)
32 inch
40 (1.6)
40 (1
.6)
150
(5.9
)40
(1.6
)
PUMA VT1100M
37 (1
.5)
40 (1.6)
580 (22.8)
350 (13.8) 350 (13.8)
110 (4.3)
150 (5.9)
485 (19.1)500 (19.7)
135 (5.3)
8 (0
.3)
45 (1
.8)15
0 (5
.9)
187
(7.4
)26
8 (1
0.6)
1000
(39.
4)45 (1.
8)
25 (1.0)
110 (4.3)
150 (5.9)
212 (8.3)
74.2
(2.9
)10
0(3
.9)
56 (2.2)
72.5
(2.9
)
113 (
4.4)
60 (2.4)
37 (1
.5)
60(2.4)
40(1.6)
32 inch
37 (1
.5)
110 (4.3)150 (5.9)
40 (1.6)
77 (3.0
)
77 (3.0
)
142 (5.6)
32 (1.3)
8 (0.3)
150 (5.9)
150
(5.9
)
65 (2.6)95 (3.7)
111 (4.4) 100 (3.9)350 (13.8) 350 (13.8)
37 (1
.5)
72.5
(2.9
)14
4.2
(5.7
)10
0(3
.9)
135 (5.3)
191 (7.5)
56 (2.2)
70 (2
.8)
70 (2.8
)
60 (2.4)
60 (2.4)
32 inch
37 (1
.5)
19
External Dimensions
Unit: mm (inch)
PUMA VT450 / VT450M /PUMA VT450-2SP / VT450M-2SP
PUMA VT750 / VT750MPUMA VT750-2SP / VT750M-2SP
2021
(79.
6)
1445 (56.9) 1445 (56.9)5 (0.2)
470
(18.
5)
(Door Stroke)
563
(22.
2)
595 (23.4)
2491
(98.
1)20
0(7
.9)
2895 (114.0)
686 (27.0) 686 (27.0)304.5(12.0)
220.5(8.7)
454.4 (17.9) 538.5 (21.2) 5 (0.2)
415.5
(16.4
)44
0 (1
7.3)
1129 (44.4) 1129 (44.4)
Chip ConveyorRear (Option)
Chip ConveyorLeft (Option)
Chip ConveyorRight (Option)
Chip ConveyorRear (Option)
997.
4 (3
9.3)
135 (5.3)¡£
49 (1.9)¡ £
1305 (51.4) 5 (0.2) 1305 (51.4)140 (5.5) 140 (5.5)
2895 (114.0)
2890
(113
.8)
695 (27.4) 675 (26.6)70
(2.8)70
(2.8)
5 (0.2) 5 (0.2)675 (26.6) 695 (27.4)
2895 (114.0)
5 (0.2)
1129 (44.4)1129 (44.4)
1070
(42.
1)32
0 (12
.6)
1100
(43.
3)29
0(1
1.4)
Chip ConveyorLeft (Option)
Chip ConveyorRight (Option)
3009
(118
.5)
179(7.0)
1407 (55.4) 900 (35.4)5 (0.2)
2491 (98.1)
2834
(111
.6)
1070
(42.
1)66
7 (2
6.3)
640
(25.
2)
999.4 (39.3)
1339
(52.
7)
Chip ConveyorRear (Option)
1850 (72.8)
563
(22.
2)
820 (32.3)
820 (32.3)
(Door Stroke)
470
(18.
5)23
15 (9
1.1)
2785
(109
.6)
271
(10.
7)
440
(17.
3)58
5 (2
3.0)
1084 (42.7) 1850 (72.8) 1084 (42.7)
811
(31.
9)
440 (17.3) 440 (17.3)585 (23.0) 585 (23.0)825 (32.5)825 (32.5) 5 (0.2)
135 (5.3)¡£
55 (2.2) ¡ £
Chip ConveyorRear (Option)
Chip ConveyorRear (Option)
Chip ConveyorRight (Option)
Chip ConveyorLeft (Option)
3450
(135
.8)
3255
(128
.1)
5 (0.2)
195.
5(7
.7)
220(8.7)
220(8.7)
1630 (64.2) 1630 (64.2)5 (0.2)3705 (145.9)
1850 (72.8)1850 (72.8)
1070
(42.
1)32
0 (12
.6)
1100
(43.
3)29
0(1
1.4)
1084 (42.7) 1084 (42.7)
Chip ConveyorLeft (Option) Chip Conveyor
Right (Option)
210(8.3)
1670 (65.7) 5 (0.2) 900 (35.4)
2785 (109.6)
3450
(135
.8)
3255
(128
.1)
1070
(42.
1)66
7 (2
6.3)
640
(25.
2)
811 (31.9)
2315 (91.1)
1282
(50.
5)
Chip ConveyorRear (Option)
Top View Top View
Side View Side View
Front View Front View
20
External Dimensions
Unit: mm (inch)
PUMA VT900 / VT900MPUMA VT900-2SP / VT900M-2SP
PUMA VT1100 / VT1100M
471
(18.
5)20
45 (8
0.5)
3516
(138
.4)
1000
(39.
4)
1136 (44.7)4270 (168.1)1136 (44.7)
530 (20.9)611.5 (24.1)651.5 (25.6) 938.5 (36.9) 938.5 (36.9)490 (19.3) 110(4.3)
722
(28.
4)
960 (37.8)
(Door Stroke)
135 (5.3)¡£55 (2.2) ¡£
640
(25.
2)49
0 (1
9.3)
2470
.7(9
7.3)
Chip ConveyorRear (Option)
Chip ConveyorRear (Option)
Chip ConveyorLeft (Option)
Chip ConveyorRight (Option)
990 (39.0) 1050 (41.3)
10 (0.4)
90(3.5)
90(3.5)
1050 (41.3) 990 (39.0)
2130 (83.9)2130 (83.9)
4270 (168.1)
960 (37.8)
10 (0.4)
1136 (44.7)1136 (44.7)
1070
(42.
1)
1070
(42.
1)32
0(1
2.6)
320 (
12.6)
3621
(142
.6)
Chip ConveyorLeft (Option) Chip Conveyor
Right (Option)
3455
(136
.0)
1295 (51.0) 2 (0.1) 728 (28.7) 425 (16.7)
2450 (96.5)
255
(10.
0)16
50 (6
5.0)
320 (
12.6)
1140
(44.
9)
1000 (39.4)2045 (80.5)
3621
(142
.6)
1070
(42.
1)66
7 (2
6.3)
3050 (120.1) 717 (28.2)
5 (0.2)
640
(25.
2)12
89 (5
0.7)
Chip ConveyorRear (Option)
900
(35.
4)24
05 (9
4.7) 33
05 (1
30.1
)
150(5.9) 5 (0.2)
1375 (54.1) (Door) 1300 (51.2) (Door Stroke) 20 (0.8)
270
(10.
6)
695
(27.
4)60
0 (2
3.6)
895 (35.2)736 (29.0)1219 (48.0)
987
(38.
9)
1634 (64.3)
R30
0(1
1.8)
Chip ConveyorRear (Option)
Chip ConveyorRight (Option)
2850 (112.2)
1375 (54.1) 1320 (52.0)
5 (0.2)
150 (5.9)
1634 (64.3)
1367
(53.
8)61
0 (2
4.0)
3700
(145
.7)
312
(12.
3)
Chip ConveyorRight (Option)
120 (4.7) 2270 (89.4) 15 (0.6) 900 (35.4)3305 (130.1)270 (10.6)
1360
(53.
5)60
0 (2
3.6)37
00 (1
45.7
)
4012
(158
.0)
311.
7(1
2.3)
1370
(53.
9)66
7 (2
6.3)
987 (38.9)
Chip ConveyorRear (Option)
Top View Top View
Side View Side View
Front View Front View
21
Machine Specifications
Description UnitPUMAVT450
PUMAVT450-2SP
PUMAVT450M
PUMAVT450M-2SP
PUMAVT750
PUMAVT750-2SP
PUMAVT750M
PUMAVT750M-2SP
Capacity
Swing over bed mm (inch) 580 (22.8) 800 (31.5)
Swing over saddle mm (inch) 450 (17.7) 610 (24.0)
Recom. turning diameter mm (inch) 380 (15.0) 450 (17.7)
Max. turning diameter mm (inch) 450 (17.7) 750 (29.5)
Max. turning length mm (inch) 450 (17.7) 760 (29.9)
Chuck size mm (inch) 305 (12) 380 (15)
TravelsX-axis mm (inch) 240 (9.4) 385 (15.2)
Z-axis mm (inch) 450 (17.7) 760 (29.9)
FeedratesRapid traverse rate X-axis m/min 20 (787.4)
Z-axis m/min 20 (787.4)
Main Spindle
Spindle speed r/min 2500 2000
Spindle nose ASA A2#8 A2#11
Spindle bearing diameter (Front) mm (inch) 120 (4.7) 160 (6.3)
Spindle through hole mm (inch) 62 (2.4) 77 (3.0)
Main spindle indexing angle (C-axis)
deg - 360 (in 0.001) - 360 (in 0.001)
Turret
No. of tool stations st 12
OD tool size mm (inch) 25 (1.0)
Max. boring bar size mm (inch) ø50 (ø2.0) ø40 (ø1.6) ø50 (ø2.0) ø60 (ø2.4)
Turret Indexing time(1 station swivel)
s 1.6 1.2 1.8 1.4
Motor
Main spindle motor kW (Hp) 22 (29.5) [15min.] {26 (34.9) [30min.]} 30 (40.2) [30min.] {37 (49.6) [30min.]}
Servo motor X/Z-axis kW (Hp) 3.0 / 4.0 (4.0 / 5.4)
Rotary tool spindle motor kW (Hp) - 4.5 (6.0) - 7.0 (9.4)
Power source
Electric power supply(rated capacity)
kVA 50 {55} 95 {105} 55 {60} 100 {110} 55 {65} 105 {125} 60 {70} 115 {140}
Machine Size
Height mm (inch) 3009 (118.5) 3450 (135.8)
Length mm (inch) 1445 (56.9) 2895 (114.0) 1445 (56.9) 2895 (114.0) 1850 (72.8) 3705 (145.9) 1850 (72.8) 3705 (145.9)
Width mm (inch) 2491 (98.1) 2785 (109.6)
Weight kg (lb) 6200(13668.5)
12400(27336.9)
6200(13668.5)
12400(27336.9)
9700(21384.5)
19400(42769.0)
9700(21384.5)
19400(42769.0)
Controller Fanuc i series Fanuc 31i Fanuc i series Fanuc 31i Fanuc i series Fanuc 31i Fanuc i series Fanuc 31i
• The specifications and information above-mentioned may be changed without prior notice.• For more details, please contact Doosan.
Standard Feature• Coolant flushing for bed
• Coolant flushing for chuck
• Coolant supply equipment
• Full enclosure chip and coolant shield
• Hydraulic chuck & actuating cylinder
• Hand tool kit, including small hand tool for operationst
• Hydraulic power unit
• Leveling jack screw & plates
• Lubrication equipment
• Soft jaws
• Standard tooling kit (tool holders & boring sleeve & U-Drill sleeve)
• Work light
Optional Feature• Air blast for chuck jaw cleaning
• Automatic door with safety device
• Chip bucket
• Coolant gun
• Drill socket
• Dual chucking pressure
• Hardened & ground jaws
• High pressure coolant
• Manual tool presetter (Removable type)
• Oil skimmer (Belt type)
• Proximity switch for chuck clamp detection
• Signal tower (yellow, red, green)
• Special chucks
• Straddle tool preparation (Piping & Solenoid valve, Exclude straddle tool)
{ } : Option
22
Machine Specifications
• The specifications and information above-mentioned may be changed without prior notice.• For more details, please contact Doosan.
Standard Feature• Coolant flushing for bed
• Coolant flushing for chuck
• Coolant supply equipment
• Full enclosure chip and coolant shield
• Hydraulic chuck & actuating cylinder
• Hand tool kit, including small hand tool for operationst
• Hydraulic power unit
• Leveling jack screw & plates
• Lubrication equipment
• Soft jaws
• Standard tooling kit (tool holders & boring sleeve & U-Drill sleeve)
• Work light
Optional Feature• Air blast for chuck jaw cleaning
• Automatic door with safety device
• Chip bucket
• Coolant gun
• Drill socket
• Dual chucking pressure
• Hardened & ground jaws
• High pressure coolant
• Manual tool presetter (Removable type)
• Oil skimmer (Belt type)
• Chuck clamp confirmation
• Signal tower (yellow, red, green)
• Special chucks
• Straddle tool preparation (Piping & Solenoid valve, Exclude straddle tool)
Description UnitPUMAVT900
PUMAVT900-2SP
PUMAVT900M
PUMAVT900M-2SP
PUMAVT1100
PUMAVT1100M
Capacity
Swing over bed mm (inch) 1000 (39.4) 1270 (50.0)
Swing over saddle mm (inch) 700 (27.6) 1000 (39.4)
Recom. turning diameter mm (inch) 610 (24.0) 800 (31.5)
Max. turning diameter mm (inch) 900 (35.4) 1100 (43.3)
Max. turning length mm (inch) 850 (33.5) 1000 (39.4)
Chuck size mm (inch) 609 (24) 800 (32)
TravelsX-axis mm (inch) 470 (18.5) 580 (22.8)
Z-axis mm (inch) 850 (33.5) 1000 (39.4)
FeedratesRapid traverse rate X-axis m/min 20 (787.4)
Z-axis m/min 20 (787.4)
Main Spindle
Spindle speed r/min 1800 850
Spindle nose ASA ISO 702-1 A2#15 ISO 702-4-No15
Spindle bearing diameter (Front) mm (inch) 200 (7.9)
Spindle through hole mm (inch) 107 (4.2) 100 (3.9)
Main spindle indexing angle (C-axis)
deg - 360 (in 0.001) - 360 (in 0.001)
Turret
No. of tool stations st 12
OD tool size mm (inch) 32 (1.3)
Max. boring bar size mm (inch) ø80 (ø3.1)
Turret Indexing time(1 station swivel)
s 2.0 1.6 2.2
Motor
Main spindle motor kW (Hp) 45 (60.3) [30min.] 60 (80.5) [10min.]
Servo motor X/Z-axis kW (Hp) 4.0 / 4.0 (5.4 / 5.4) 4.0 / 7.0 (5.4 / 9.4)
Rotary tool spindle motor kW (Hp) - 7.0 (9.4) - 11 (14.8)
Power source
Electric power supply(rated capacity)
kVA 75 145 80 155 90 100
Machine Size
Height mm (inch) 3621 (142.6) 4012 (158.0)
Length mm (inch) 2130 (83.9) 4270 (168.1) 2130 (83.9) 4270 (168.1) 2850 (112.2)
Width mm (inch) 3050 (120.1) 3305 (130.1)
Weight kg (lb)12500
(27557.4)25000
(55114.8)12500
(27557.4)25000
(55114.8)22000
(48501.0)
Controller Fanuc 32i Fanuc 31i Fanuc 32i Fanuc 31i Fanuc 32i
23
NC Unit Specifications
Item Spec. Doosan Fanuc i series Fanuc 32i Fanuc 31i
ControlsControlled axes X, Z, C (!) X, Z, C (!) X1, Z1, X2, Z2Simultaneously controlled axes Std. 2 axes 4 axes (!) 3 axes (!) 4 axes
Axis Functions
Backlash compensation 0~±9999 pulses ○ ○ ○
Cs contouring control ○(!) ○(!) -Follow-up / Chamfering on/off ○ ○ ○
HRV2 control ○ ○ ○
Least input increment 0.001mm / 0.0001" ○ ○ ○
Stored stroke check1 Overtravel control ○ ○ ○
Operation
Automatic operation(memory) / Buffer register ○ ○ ○
Handle incremental feed X1, X10, X100 ○ ○ ○
Search function Sequence NO. / Program NO. ○ ○ ○
Interpolation
1st, reference position return Manual, G28 ○ ○ ○
2nd reference position return G30 ○ ○ ○
Reference position return check G27 ○ ○ ○
Circular interpolation G02 ○ ○ ○
Continuous thread cutting ○ ○ ○
Dwell G04 ○ ○ ○
Linear interpolation G01 ○ ○ ○
Multiple threading /Thread cutting retract ○ ○ ○
Polar coordinate interpolation ○(!) ○(!) -Thread cutting / Synchronous cutting ○ ○ ○
Feed Functions
Feed per minute / Feed per revolution ○ ○ ○
Feedrate override 0 - 200% (10% unit) ○ ○ ○
Jog feed override 0 - 2000 mm/min ○ ○ ○
Rapid traverse override F0/ 25 / 100% ○ ○ ○
Tangential speed constant control ○ ○ ○
Axuiliary &Spindle Functions
1st Spindle orientation ○ ○ ○
Constantant surface speed control ○ ○ ○
M-function M3 digit ○ ○ ○
Multi-spindle control ○(!) ○(!) ○
Rigid tapping ○ ○ ○
Spindle speed override 0~150% ○ ○ ○
ProgrammingFunctions
Absolute / Incremental programming ○ ○ ○
Canned cycle for drilling / turning ○ ○ ○
Custom macro ○ ○ ○
Decimal point programming /pocket calculator type decimal point programming ○ ○ ○
Direct drawing dimension programming ○ ○ ○
Manual guide i Conversational programming ○ ○ ○
Maximum program dimension ±9 digits ○ ○ ○
Multi repetitive canned cycle G70~G76 ○(!) ○ ○
Optional block skip(without hardware) Total 9 (Only NC function) - ○ ○
Sequence number N5 N8 N8Programmable data input G10 ○ ○ ○
Sub program call Nested holds 4 10 10Tape format for FANUC series 10/11 ○ ○ -Tape format for FANUC series 15 - - ○
Work coordinate system selection G52~G59 ○ ○ ○
Tool Functions
Auto tool offset ○ ○ ○
Tool monitoring system - Opt. Opt.Direct input of tool offset value measured B ○ ○ ○
Tool geometry / wear compensation Geometry & wear data ○ ○ ○
Tool life management ○ ○ ○
Tool nose radius compensation G40~G42 ○ ○ ○
T-code function T2+2 digits ○ ○ ○
Tool offset pairs 64 64 32Tool offset value counter input - ○ ○
Editing Op.Functions
Background editting ○ ○ ○
Expanded part program editting Copy, Move, Change of NC program ○ ○ ○
No. of Registered programs 400ea 500ea 500eaPart program editing / Program protect ○ ○ ○
Part program storage length*1 1280m 640m 640m
Setting & Display
Display of spindle speed and T-code at all screen ○ ○ ○
Help function Alarm&Operation display ○ ○ ○
Self diagnostic function ○ ○ ○
Servo setting screen / Spindle setting screen ○ ○ ○
Tool path graphic display ○ Opt. (!) ○
Data Input &Output
I/O interface RS-232C ○ ○ ○
Memory card input and output ○ ○ ○
Reader puncher control CH1 interface ○ ○ ○
Other Functions
Ethernet function Embedded ethernet function ○ ○ ○
MDI / DISPLAY unit 10.4" color TFT LCD 10.4" color TFT LCD 10.4" color TFT LCDPMC system ○ ○ ○
○: Standard OPT : Option (!) : only M type*1 : Standard Part program length is different on export condition. On the addition of optional functions, its length can be reduced.
Doosan Machine Tools
Head OfficeYeonkang Bldg., 6th FL., 270, Yeonji-dong,
Jongno-gu, Seoul, Korea
Tel +82-2-3670-5345 / 5362
Fax +82-2-3670-5382
Doosan Machine Tools America19A Chapin Rd., Pine Brook, NJ 07058, U.S.A.
Tel +1-973-618-2500
Fax +1-973-618-2501
http://www.doosanmachinetools.com www.facebook.com/doosanmachinetools
Doosan Machine Tools ChinaRoom 101,201,301, Building 39 Xinzhuan Highway
No.258 Songjiang District,China Shanghai(201612)
Tel +86 21-5445-1155
Fax +86 21-6405-1472
Doosan Machine Tools EuropeEmdener Strasse 24, D-41540 Dormagen, Germany
Tel +49-2133-5067-100
Fax +49-2133-5067-001
Doosan Machine Tools Japan#2412, Mita Kokusai Bldg. 1-4-28 Mita,
Minato-ku, Tokyo 108-0073, Japan
Tel +81 3 5730 9013
Fax +81 3 5730 9016
Doosan Machine Tools India106 / 10-11-12, Amruthahalli, Byatarayanapura,
Bellary road, Bangalore-560 092, India
Tel +91-80-4266-0122 / 121 / 100
* For more details, please contact Doosan Machine Tools.* The specifications and information above-mentioned may be changed without prior notice.* Doosan Machine Tools Co., Ltd. is a subsidiary of MBK Partners, a Korean private equity firm. The trademark is used under a licensing
agreement with Doosan Corporation, the registered trademark holder.
ver. EN 160502 SU