gpon access systems product catalog
TRANSCRIPT
Access Systems Product Catalog
Fiber to the Future®
Table of Contents
The information contained herein is for informational purposes only. Technical claims listed depend on various technical assumptions.
Your experience with these products may diff er if you operate the products in an environment, which is diff erent from the technical as-
sumptions. Alphion reserves the right to modify these specifi cations without any prior notice. Alphion makes no warranties, expressed
or implied, on the information contained in this document.
2
About AlphionAOLT-4000-CH AOLT-4000 ChassisAOLT-4000N AOLT-4000 19” ChassisAOLT-4000-CTL Control Line CardAOLT-4000-SWT Switch / Timing CardAOLT-4000-GLCP GPON Protected Path Line CardAONT-100 SFU Single Family UnitAONT-100C SFU Compact Single Family UnitAONT-100Z Outdoor Single Family UnitAONT-1010 Single Family UnitAONT-1240 GPON SFU GatewayAONT-1040 GPON SFU GatewayAONT-1440 Single Family UnitAONT-UPS Uninterruptable Power SupplyAONT-3030 Multi-Dwelling UnitAONT-3330 Multi-Dwelling UnitAONT-300 Multi-Dwelling UnitARGT-1040 Remote Gateway terminalASPL series Passive Optical SplittersAEMS Software Element Management System SoftwarePON.ext™ PON Extension SystemContact Information
3
4-5
6-7
8
9
10
11-12
13-14
15-16
17-18
19-20
21-22
23-24
25
26-27
28-29
30-31
32-33
34-35
36-37
38-3940
Fiber to the Future® 3
Alphion...enabling the photonic future®
Access Systems
The Alphion access system product line includes the AOLT-4000 GPON Optical Line Terminal, the AONT family of GPON Optical Network Terminals, PON Extenders, AEMS Element Management System and a wide selec-tion of active and passive hardware components for power and fi ber management, passive splitters, distribu-tion frames and more.
Alphion has created a complete GPON technology platform that not only leverages the most sophisticated industry standards, but is also designated for integration into standards-based OEM platforms and service provider networks.
Alphion is recognized as the leader in developing all-optical PON exten-sion solutions. Alphion’s PON.ext™ technology allows carriers to extend the reach of existing PON network from 20 km to 60 km while also in-creasing the subscriber base by four times.
Fiber to the Future®4
AOLT-4000-CH
AOLT-4000GPON Optical Line Terminal
Feature Summary9 RU, ETSI 515 mm hole to hole rack mount, and 500 mm aperture
537 mm W x 300 mm D x 400 mm H
Operating temperature range -5 to +50°C, 5% to 90% non - condensing relative humidity
Requires front access only
Redundant controllers and aggregation switches
Supports card hot swap
Redundant 1+1 control and aggrega-tion switches option
1+1 (from diff erent cards) uplink pro-tection option
1:1 (same card) uplink protection op-tion
Dual shelf power inputs
Dual BITS/SSU clock inputs
Central offi ce dry alarms contacts via the control card
Integrated fi ber management
Forced air cooling with fi eld replace-able air fi lter
ApplicationsThe AOLT-4000 is designed for Carrier Central Offi ce or MSO Hub environments for enabling cost-eff ective FTTx services.
Flexible Confi gurationTwo control card slots for 1+1 Control cards. Two switch slots for 1+1 Aggrega-tion switch cards with redundant 10-GbE and 1-GbE Service Node Interface (SNI) uplinks. Ten Line card slots.
Data Plane ConnectivityThe AOLT-4000’s data plane consists of redundant 10-GbE connections to each card slot from the two dedicated double-width AOLT-4000-SWT slot in the shelf.
Control Plane ConnectivityThe AOLT-4000’s control plane consists of redundant 1-GbE connections to each card slot from the two dedicated AOLT-4000-CTL slots.
Synchronization ConnectionsInputs for redundant BITS/SSU timing for GPON and TDM synchronization and outputs for sourcing clocks for external synchronization use.
Switch CapacityDual star redundant architecture with 20 Gb/s bandwidth to each card slot and 400 Gb/s bandwidth total capacity.
High AvailabilityHigh Availability architecture where removal or insertion of any single card does not aff ect existing connections on other cards. Even in a system with a single AOLT-4000-CTL card, a failure of the control card does not aff ect the working traf-fi c. To increase control plane availability, a second mate AOLT-4000-CTL card can be inserted in the AOLT-4000 chassis, providing 1+1 redundancy for the control plane. Likewise to increase data plane availability, a second mate AOLT-4000-SWT card can be inserted in the AOLT-4000 chassis, providing 1+1 redundancy for the data and signaling plane.
AEMS or SNMP ManagedWith the AOLT-4000-CTL card installed the AOLT-4000 is either remotely or locally managed from either Alphion’s Element Management System (AEMS) or with a 3rd party EMS using SNMP or a legacy NMS.
Fiber to the Future® 5
AOLT-4000-CH
SPECIFICATIONS
Capacity2 slots Redundant control cards (AOLT-4000- CTL)2 slots (double-width) Redundant switch and timing cards (AOLT-4000-SWT)10 slots GPON Line Cards (AOLT-4000-GLCP)
Management interfaceProtocol SNMPv2cInterface 10/100Base-TPorts 2
Craft interfaceUSB 2.0 (type B connectors)
BITS/SSU clockTwo inputs 75 ohms BNC and DB9Two outputs 75 ohms BNC and DB9
AlarmFive outputs DB15
Power supplyDual input Individually controlled by circuit breaker -40.0 to +56.7 VDC
CoolingForced air cooling with fans
DimensionsW x D x H 537 mm x 300 mm x 400 mmFrame mounting ETSI 515 mm hole to hole, and 500 mm aperture
Operating environmentTemperature -5 to +50°CRelative humidity 5% to 90% (non-condensing)
ComplianceEMC EN55022, CISPR-22 Class ASafety EN60950, UL60950, CE, Optical IEC-60825-1 Class B Laser safety per G.664Environmental EN300 019-1-3, QM-333 ‘B2” CategoryChassis EN300 119-4Transient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
Fiber to the Future®6
AOLT-4000N
AOLT-4000NGPON Optical Line Terminal
Feature Summary12 RU, ANSI standard 19 inch rack mount chassis
442 mm W x 300 mm D x 533 mm H
Operating temperature range -5 to +50°C, 5% to 90% non - condensing relative humidity
Requires front access only
Redundant controllers and aggregation switches
Supports card hot swap
Redundant 1+1 control and aggrega-tion switches option
1+1 (from diff erent cards) uplink pro-tection option
1:1 (same card) uplink protection op-tion
Dual shelf power inputs
Dual BITS/SSU clock inputs
Central offi ce dry alarms contacts via the control card
Integrated fi ber management
Forced air cooling with fi eld replace-able air fi lter
ApplicationsThe AOLT-4000N is designed for Carrier Central Offi ce or MSO Hub environments for enabling cost-ef-fective FTTx services.
Flexible Confi gurationTwo control card slots for 1+1 Con-trol cards. Two switch slots for 1+1 Aggregation switch cards with redundant 10-GbE and 1-GbE Service Node Inter-face (SNI) uplinks. Ten Line card slots.
Data Plane ConnectivityThe AOLT-4000N’s data plane consists of redundant 10-GbE connections to each card slot from the two dedicated double-width AOLT-4000-SWT slot in the shelf.
Control Plane ConnectivityThe AOLT-4000N’s control plane consists of redundant 1-GbE connections to each card slot from the two dedicated AOLT-4000-CTL slots.
Synchronization ConnectionsInputs for redundant BITS/SSU timing for GPON and TDM synchronization and outputs for sourcing clocks for external synchronization use.
Switch CapacityDual star redundant architecture with 20 Gb/s bandwidth to each card slot and 400 Gb/s bandwidth total capacity.
High AvailabilityHigh Availability architecture where removal or insertion of any single card does not aff ect existing connections on other cards. Even in a system with a single AOLT-4000-CTL card, a failure of the control card does not aff ect the working traf-fi c. To increase control plane availability, a second mate AOLT-4000-CTL card can be inserted in the AOLT-4000N chassis, providing 1+1 redundancy for the control plane. Likewise to increase data plane availability, a second mate AOLT-4000-SWT card can be inserted in the AOLT-4000N chassis, providing 1+1 redundancy for the data and signaling plane.
AEMS or SNMP ManagedWith the AOLT-4000-CTL card installed the AOLT-4000N is either remotely or lo-cally managed from either Alphion’s Element Management System (AEMS) or with a 3rd party EMS using SNMP or a legacy NMS.
Fiber to the Future® 7
AOLT-4000N
SPECIFICATIONS
Capacity2 slots Redundant control cards (AOLT-4000- CTL)2 slots (double-width) Redundant switch and timing cards (AOLT-4000-SWT)10 slots GPON Line Cards (AOLT-4000-GLCP)
Management interfaceProtocol SNMPv2cInterface 10/100Base-TPorts 2
Craft interfaceUSB 2.0 (type B connectors)
BITS/SSU clockTwo inputs 75 ohms BNC and DB9Two outputs 75 ohms BNC and DB9
AlarmFive outputs DB15
Power supplyDual input Individually controlled by circuit breaker -40.0 to +56.7 VDC
CoolingForced air cooling with fans
DimensionsW x D x H 442 mm x 300 mm x 533 mmFrame mounting 19 inch rack mount
Operating environmentTemperature -5 to +50°CRelative humidity 5% to 90% (non-condensing)
ComplianceEMC EN55022, CISPR-22 Class ASafety EN60950, UL60950, CE, Optical IEC-60825-1 Class B Laser safety per G.664Environmental EN300 019-1-3, QM-333 ‘B2” CategoryChassis EN300 119-4Transient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
Fiber to the Future®8
AOLT-4000-CTL
AOLT-4000-CTLGPON Control Card
Feature Summary1+1 master/slave redundancy option for High Availability applications
Fully Hot-swappable
Redundant power supply and control plane
Two 10/100Base-T RJ-45 ports for EMS
Front-panel Telco Alarm Cut-off (ACO) button
Front-panel critical, major and minor alarm indicator LEDs
Front-panel LED test button
Front-Panel USB2.0 connector for local craft PC
2Gbyte on-board FLASH for software im-age and confi guration data storage
SNMP based management of the AOLT-4000 platform
Applications One or two AOLT-4000-CTL cards, installed at either end of an AOLT-4000 chassis, can be used to control and manage the AOLT-4000 system. High Performance Control Plane The AOLT-4000-CTL card extends a dedicated, out-of-band GbE control plane link, over the backplane, to each slot in the AOLT-4000 chassis. The AOLT-4000-CTL card contains a high-performance embedded CPU that executes the system-level control and management plane software for the AOLT-4000 platform, including system-level resource allocations, critical alarm/event reporting, etc. The card’s software implements a fl exible, low-overhead inter-card communications frame-work that assists in fast protection switching of the switch/timing and GPON line cards in the AOLT 4000 chassis, or resources in them.
Persistent Storage Two GBytes of persistent storage are available for confi guration data and software images for all the cards in the AOLT-4000 chassis.
High Availability To increase the control plane availability, a second mate AOLT-4000-CTL card can be inserted in the AOLT-4000 chassis, providing 1+1 redundancy. Failure of the ac-tive or standby AOLT-4000-CTL card, or both of them, does not aff ect the working traffi c in the AOLT-4000 chassis. The AOLT-4000-CTL card also ensures high avail-ability for other cards in the system through dedicated hardware level inter-card signaling.
Management The AOLT-4000-CTL supports SNMP based management of all the cards in the AOLT-4000 platform from Alphion’s Element Management System (AEMS). Using a GbE control plane link to AOLT-4000-SWT (the AOLT-4000 platform’s Switch/Tim-ing card), the AOLT-4000-CTL card supports in-band management of the AOLT-4000 system through one of the network uplink ports of the Switch/Timing card.
Fiber to the Future® 9
AOLT-4000-SWT
AOLT-4000-SWTGPON Switch / Timing Card
Feature SummaryHot swappable, with 1+1 master and slave redundancy option
28 Gb/s (2 x 10-GbE and 8 x 1-GbE) uplink, and 10-GbE backplane interface to each line card
Line-rate unicast packet forwarding and multicast replication
Independent VLAN Learning (IVL)
16K MAC addresses, 4094 VLANs
Port based VLAN, IEEE 802.1ad, Q-in-Q VLAN stacking
Eight priority re-marking, DSCP to 802.1p mapping
Sophisticated packet fi ltering based on any Layer 2-7 fi eld
Rate control of broadcast, unknown uni-cast, and multicast packets
IEEE 802.3ad link aggregation across up-link Ethernet links
IEEE 802.1w RSTP
IGMP snooping/proxy
1024 Layer 2 multicast groups
DHCP Option 82
Support for Jumbo frames (up to 12K bytes)
Network for local TDM timing synchroni-zation
Applications As a key card of the AOLT-4000 platform, AOLT-4000-SWT enables effi cient and controlled forwarding of Ethernet/packet traffi c between the GPON line cards and the up-link service/edge node (typically, a router or a switch). Robust Layer-2 Switching AOLT-4000-SWT contains a high-capacity switching engine that supports hard-ware based learning of up to 16K MAC addresses, 4094 VLANs, and Independent VLAN Learning (IVL) based forwarding. It also supports MAC, protocol and subnet based VLANs; IEEE 802.1ad Q-in-Q VLAN stacking; and IEEE 802.3ad link aggrega-tion. Featuring an aggregate switching capacity of 200 Gb/s, the AOLT-4000-SWT support line-rate forwarding of unicast and multicast packets, for all packet sizes, under all conditions.
Packet Filtering/Classifi cation AOLT-4000-SWT includes a fl exible packet fi lter/classifi er that can fi lter packets based on any Layer 2-7 fi eld, including MAC address, IP address, VLAN ID, packet type, etc, supporting multiple lookups and actions per packet. Filter actions in-clude dropping, priority re-marking, rate limiting, etc. The AOLT-4000-SWT card also support access control list (ACL) based policing; fl ow metering, with a granu-larity of 64 kb/s to 1 Gb/s; two rate three color marking (trTCM); and class-based marking for SLAs.
Intelligent QoS AOLT-4000-SWT supports 8 priority queues per port, head of line blocking (HOLB) prevention, service aware fl ow control, bandwidth guarantee per class of ser-vice and/or per port, DSCP re-marking, DSCP to 802.1p mapping, and 2-levels of drop precedence per queue. It features a packet scheduler that supports multiple scheduling algorithms, including strict priority (SP), weighted round robin (WRR), and defi cit round robin (DRR). The AOLT-4000-SWT also supports individual rate limiting of broadcast, unknown unicast and multicast traffi c on a per port basis.
High Availability AOLT-4000-SWT supports 1+1 redundancy, protecting the AOLT-4000 platform’s data plane and TDM synchronization clocks from a single card failure.
Fiber to the Future®10
AOLT-4000-GLCP
AOLT-4000-GLCPGPON Protected Path Line Card
Feature Summary4 GPON active ports per card
4 optional protection ports per card
1:1 protectable when installed in an AOLT-4000 chassis
Hot swappable cards
Dual 10 Gb/s interface to the backplane for data-plane redundancy
Dual 1 Gb/s interface to the backplane for control-plane redundancy
On-board L2 switch with intelligent QoS & multicast support
8K MAC address table
4096 VLANs
Full T-CONT type support
4095 Alloc-Ids per GPON port
256 allocations in BW MAP
Applications The AOLT-4000-GLCP card provides the GPON interface with path protection for the AOLT-4000 system. GPON The AOLT-4000-GLCP card is a fully FSAN and ITU-T G.984 compliant GPON system, with support for a data rate of 2.488 Gb/s in the downstream and 1.244 Gb/s in the upstream direction and support for the Class B+ optical link budget on each GPON port. In addition, in accordance with G.984, the AOLT-4000-GLCP card sup-ports AES (128-bit key) in the downstream direction and RS(255,239) FEC in the downstream and upstream directions.
Back Plane Connectivity The AOLT-4000-GLCP provides redundant 10 Gb/s data plane connections to both the active and standby Switch and Timing cards (AOLT-4000-SWT) in the AOLT-4000 chassis. In addition, the GLCP also provides a redundant 1 Gb/s control plane connectivity to each of the two Control Cards (AOLT-4000-CTL) in the AOLT-4000 Chassis.
High Performance The GLCP card incorporates a high performance full-wire-speed QoS enabled L2 switch that supports MAC learning and fi ltering, 802.1Q VLANs, 802.1ad Q-in-Q VLAN Stacking with single and dual VLAN tag manipulation, and QoS (802.1p and DSCP to 802.1p mapping). The GLCP also supports IGMP snopping and DHCP re-lay agent with Option 82 support for line identifi cation.
GPON Protection The GLCP supports a 1:1 GPON Path Protection with the optional redundant ports populated with the appropriate transceivers.
GPON DBA The GLCP provides support for both NSR and SR DBA (G.984.3) piggy-back DBRu report mode 0, including concurrent support for DBR mode 0 and “idle GEM” mode. The GLCP supports all the T-CONT types ( Type 1 through Type 5). It sup-ports up to 4095 Alloc-Ids per GPON port and up to 256 allocations in BW MAP.
Fiber to the Future® 11
Built-in Triplexer for Video RF-Overlay
Indoor wall or table mount
Four 10/100Base-T Ethernet RJ-45 Ports
2 analog 2-wire RJ-11 (POTS) VoIP SIP voice ports, G.711 codec, 5 REN per port
CLASS 5 Voice Services
Lifeline POTS when used with the AONT-100-UPS
Built-in L2 switch , 256 MAC addresses and 16 VLAN VIDs
MAC address limiting
Customer VLAN tagged (802.1p), prior-ity tagged and untagged frames
ToS/DSCP to 802.1p mapping
IGMPv1/v2/v3 snooping and fi ltering
Ethernet UNI output shaping, and up-stream scheduling
GPON “dying gasp” power loss indica-tion
AONT-100GPON Single Family Unit Optical Network Terminal
Feature SummaryApplications The AONT-100 has been optimized for single family homes or apartments and small home of-fi ces (SOHO) that require an RF-overlay for video delivery.
High Bandwidth GPON The AONT-100 is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. In addition it supports down-stream AES (128-bit key) and downstream and upstream FEC RS(255,239).
Ethernet Quality of Service The AONT-100 has extensive Ethernet QoS features, including 802.3x fl ow control, DSCP to 802.1p mapping, upstream congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent and robust buff er and queue management for Ethernet traffi c, with individual prioritizable queues, ensures that tiered residential service off erings based on diff erent bit-rates and QoS can be supported.
Security The AONT-100 comes with the latest security features, including MAC address spoofi ng protection, MAC/IP address port binding, MAC/IP address limiting on a per port basis, local port-to-port switching blocking option, 802.1X MAC-based authentication, per-port Access Control List (ACL) based on port, MAC address and Ether-type, and DOS prevention.
Flexible Management The AONT-100 is managed from the AOLT-4000 OLT over the GPON’s OMCI chan-nel. The AOLT in turn is managed with either Alphion’s Element Management System (AEMS) that provides confi guration, profi le based provisioning, event and fault management and performance monitoring for the AONT, or a 3rd party EMS using SNMP or a legacy NMS.
AONT-100
Fiber to the Future®12
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+)Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine Rate Upstream: 1.24416 Gb/s; Down- stream: 2.48831 Gb/sOutput Power 0.5 to +5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmDistance up to 60 km (depending on split ratio and reach extension)Connector SC/APC (required for RF-Overlay)
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
Video interfacesType Coax F-Connector
Data interfacesType Four 10/100Base-T RJ-45 Ethernet interfacesRate & Duplex Auto-negotiationMDI/MDIX Auto-sensingVLAN Support 802.1Q with VLAN tag manipulationMAC & VLAN Table 256 MAC Address and 16 VLAN IDsPriority VLAN 802.1p, VID=0 802.1p, ToS/ DSCP to 802.1p mapping
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
Voice interfacesType Two FXS POTS RJ-11 interfaces, 5 REN, Balance RingVoIP SIP (Session Initiation Protocol) (RFC3261 and SDP (RFC2327)Codec Multiple codec supportDTMF RFC2833 or In-bandTones and Ring Confi gurableDial Plan Confi gurableFAX and Modem G.711 for FAX/mode in TTY or T.38 FAXCLASS 5 Services Yes, VariousConditioning Echo Cancellation, Voice Activity Detection, Comfort Noise Generaliza- tion
EnvironmentalTemperature -5 to +50°CRelative humidity 5% to 95% (non-condensing)
PhysicalW x D x H 13” x 10” x 4” / 330 mm x 254 mm x 102 mmPowering +12 VDCMounting Wall and table mounting
ComplianceEMC EN55022, CISPR-22 Class A, ETSI 300 386, TEC SD/EMI-01/02 Sept.2001Safety EN60950, UL60950, CE, Optical IEC-60825-1 Class B Laser safety per G.664Environmental QM-333 ‘B2” CategoryTransient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-100
Fiber to the Future® 13
Small form factor
Indoor wall or table mount
Four 10/100Base-T Ethernet RJ-45 Ports
2 analog 2-wire RJ-11 (POTS) VoIP SIP voice ports, G.711 codec, 5 REN per port
CLASS 5 Voice Services
Lifeline POTS when used with the AONT-100-UPS and power shedding
Built-in L2 switch , 256 MAC addresses and 16 VLAN VIDs
MAC address limiting
Customer VLAN tagged (802.1p), prior-ity tagged and untagged frames
ToS/DSCP to 802.1p mapping
IGMPv1/v2/v3 snooping and fi ltering
Ethernet UNI output shaping, and up-stream scheduling
GPON “dying gasp” power loss indica-tion
AONT-100CGPON Single Family Unit Optical Network Terminal
Feature SummaryApplications The AONT-100C has been optimized for single family homes or apartments and small home of-fi ces (SOHO) that do not require an RF-overlay for video delivery.
High Bandwidth GPON The AONT-100C is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. In addition, it supports down-stream AES (128-bit key) and downstream and upstream FEC RS(255,239).
Ethernet Quality of Service The AONT-100C has extensive Ethernet QoS features, including 802.3x fl ow con-trol, DSCP to 802.1p mapping, upstream congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent and robust buff er and queue management for Ethernet traffi c, with individual prioritizable queues, ensures that tiered residential service off erings based on diff erent bit-rates and QoS can be supported.
Security The AONT-100C comes with the latest security features, including MAC address spoofi ng protection, MAC/IP address port binding, MAC/IP address limiting on a per port basis, local port-to-port switching blocking option, 802.1X MAC-based authentication, per-port Access Control List (ACL) based on port, MAC address and Ether-type, and DOS prevention.
Small form-factor A space conscious package for simplifi ed wall or table mounting.
Flexible Management The AONT-100C is managed from the AOLT-4000 OLT over the GPON’s OMCI chan-nel. The AOLT in turn is managed with either Alphion’s Element Management Sys-tem (AEMS) that provides confi guration, profi le based provisioning, event and fault management and performance monitoring for the AONT, or a 3rd party EMS using SNMP or a legacy NMS.
AONT-100C
Fiber to the Future®14
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+)Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine Rate Upstream: 1.24416 Gb/s; Down- stream: 2.48831 Gb/sOutput Power +0.5 to +5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmDistance up to 60 km (depending on split ratio and reach extension)Connector SC/UPC
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
Video interfacesType Not applicable, IP Video over the Data interface
Data interfacesType Four 10/100Base-T RJ-45 Ethernet interfacesRate & Duplex Auto-negotiationMDI/MDIX Auto-sensingVLAN Support 802.1Q with VLAN tag manipulationMAC & VLAN Table 256 MAC Address and 16 VLAN IDsPriority VLAN 802.1p, VID=0 802.1p, ToS/ DSCP to 802.1p mapping
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
Voice interfacesType Two FXS POTS RJ-11 interfaces, 5 REN, Balance RingVoIP Protocol SIP (Session Initiation Protocol) (RFC3261 and SDP (RFC2327)Codec Multiple codec supportDTMF RFC2833 or In-bandTones and Ring Confi gurableDial Plan Confi gurableFAX and Modem G.711 for FAX/mode in TTY or T.38 FAXCLASS 5 Services Yes, VariousConditioning Echo Cancellation, Voice Activity Detection, Comfort Noise Generaliza- tion
EnvironmentalTemperature -5 to +50°CRelative humidity 5% to 95% (non-condensing)
PhysicalW x D x H 5.5” x 7.1” x 1.6” / 140 mm x 180 mm x 40 mmPowering +12 VDCMounting Wall and table mounting
ComplianceEMC EN55022, CISPR-22 Class B, ETSI 300 386, TEC SD/EMI-01/02 Sept.2001Safety EN60950, UL60950, CE, Optical IEC-60825-1 Class B Laser safety per G.664Environmental QM-333 ‘B2” CategoryTransient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-100C
Fiber to the Future® 15
Built-in Triplexer for Video RF-Overlay
Outdoor wall mount
Four 10/100Base-T Ethernet RJ-45 Ports
2 analog 2-wire RJ-11 (POTS) VoIP SIP voice ports, G.711 codec, 5 REN per port
CLASS 5 Voice Services
Built-in L2 switch, 256 MAC addresses and 16 VLAN VIDs
MAC address limiting
Customer VLAN tagged (802.1p), prior-ity tagged and untagged frames
ToS/DSCP to 802.1p mapping
IGMPv1/v2/v3 optional
Ethernet UNI output shaping, and up-stream scheduling
GPON “dying gasp” power loss indica-tion
AONT-100ZGPON Outdoor Single Family Unit
Optical Network Terminal
Feature SummaryApplications The AONT-100Z has been optimized for single family homes or apartments and small home offi ces (SOHO) that require an RF-overlay for video delivery.
High Bandwidth GPON The AONT-100Z is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. In addition, it supports down-stream AES (128-bit key) and downstream and/or upstream FEC RS(255,239).
Ethernet Quality of Service The AONT-100Z has extensive Ethernet QoS features, including 802.3x fl ow con-trol, DSCP to 802.1p mapping, upstream congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent and robust buff er and queue management for Ethernet traffi c, with individual prioritizable queues, ensures that tiered residential service off erings based on diff erent bit-rates and QoS can be supported.
Security The AONT-100Z comes with the latest security features, including MAC address spoofi ng protection, MAC/IP address port binding, MAC/IP address limiting on a per port basis, local port-to-port switching blocking option, 802.1X MAC-based authentication, per-port Access Control List (ACL) based on port, MAC address and Ether-type, and DOS prevention.
Flexible Management The AONT-100Z is managed from the AOLT-4000 OLT over the GPON’s OMCI chan-nel. The AOLT in turn is managed with either Alphion’s Element Management Sys-tem (AEMS) that provides confi guration, profi le based provisioning, event and fault management and performance monitoring for the AONT, or a 3rd party EMS using SNMP or a legacy NMS.
AONT-100Z
Fiber to the Future®16
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+)Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine Rate Upstream: 1.24416 Gb/s; Down- stream: 2.48831 Gb/sOutput Power 0.5 to +5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmDistance up to 60 km (depending on split ratio and reach extension)Connector SC/APC (required for RF-Overlay)
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
Video interfacesType Coax F-Connector
Data interfacesType Four 10/100Base-T RJ-45 Ethernet interfacesRate & Duplex Auto-negotiationMDI/MDIX Auto-sensingVLAN Support 802.1Q with VLAN tag manipulationMAC & VLAN Table 256 MAC Address and 16 VLAN IDsPriority VLAN 802.1p, VID=0 802.1p, ToS/ DSCP to 802.1p mapping
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
Voice interfacesType Two FXS POTS RJ-11 interfaces, 5 REN, Balance RingVoIP SIP (Session Initiation Protocol) (RFC3261 and SDP (RFC2327)Codec Multiple codec supportDTMF RFC2833 or In-bandTones and Ring Confi gurableDial Plan Confi gurableFAX and Modem G.711 for FAX/mode in TTY or T.38 FAXCLASS 5 Services Yes, VariousConditioning Echo Cancellation, Voice Activity Detection, Comfort Noise Generaliza- tion
EnvironmentalTemperature -40 to +65°CRelative humidity 5% to 95% (non-condensing)
PhysicalW x D x H 320 mm x 250 mm x 95 mmPowering +12 VDCMounting Outside wall mounting
ComplianceEMC EN55022, CISPR-22 Class A, ETSI 300 386, TEC SD/EMI-01/02 Sept.2001Safety EN60950, UL60950, CE, Optical IEC-60825-1 Class B Laser safety per G.664Environmental QM-333 ‘B2” CategoryTransient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-100Z
Fiber to the Future® 17
Small form factor
Indoor wall or table mount
One 10/100/1000Base-T Ethernet RJ-45 Port
Built-in L2 Switch
Advanced VLAN Features
128 MAC Address and 16 VLAN group
MAC address limiting
Priority and rate controlled scheduling
ToS/DSCP to 802.1p mapping
GPON “dying gasp” power loss indica-tion
AONT-1010GPON Optical Network Terminal
Feature SummaryApplications The AONT-1010 is a compact GPON ONT designed and optimized to provide triple play services for a single family residence. The AONT-1010 has one 10/100/1000Base-T port that can be used to provide high speed data, voice and video service. The AONT-1010 sup-ports a wire speed data interface that supports advanced L2 and VLAN features for providing rate and priority controlled high speed internet access. To enable VoIP access, the AONT-1010 supports interfacing external IAD box or Home Router with voice capability through the Ethernet Interface. AONT-1010 supports video contents delivered in the form of data (by multicast or unicast).
High Bandwidth GPON The AONT-1010 is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. In addition, it supports down-stream AES (128-bit key) and downstream and upstream FEC RS(255,239).
Ethernet Quality of Service The AONT-1010 has extensive Ethernet QoS features, including 802.3x fl ow con-trol, DSCP to 802.1p mapping, upstream congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent and robust buff er and queue management for Ethernet traffi c, with individual prioritizable queues, ensures that tiered residential service off erings based on diff erent bit-rates and QoS can be supported.
Security The AONT-1010 comes with the latest security features, including MAC address spoofi ng protection, MAC/IP address port binding, MAC/IP address limiting on a per port basis, local port-to-port switching blocking option, 802.1X MAC-based authentication, per-port Access Control List (ACL) based on port, MAC address and Ether-type, and DOS prevention.
Small form-factor A space conscious package for simplifi ed wall or table mounting.
Flexible Management The AONT-1010 is managed from the AOLT-4000 OLT over the GPON’s OMCI chan-nel. The AOLT in turn is managed with either Alphion’s Element Management Sys-tem (AEMS) that provides confi guration, profi le based provisioning, event and fault management and performance monitoring for the AONT, or a 3rd party EMS using SNMP or a legacy NMS.
AONT-1010
Fiber to the Future®18
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+)Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine Rate Upstream: 1.244 Gb/s; Down- stream: 2.488 Gb/sOutput Power +0.5 to +5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmConnector SC/UPC
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
Data interfaceType 10/100/1000 Base-T RJ-45 Ethernet interfacesRate & Duplex Auto-negotiationMDI/MDIX Auto-sensingVLAN Support 802.1Q with VLAN tag manipulationMAC & VLAN Table 256 MAC Address and 16 VLAN IDsPriority VLAN 802.1p, VID=0 802.1p, ToS/ DSCP to 802.1p mapping
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
EnvironmentalTemperature -5 to +50°CRelative humidity 5% to 95% (non-condensing)
PhysicalW x D x H 125 mm x 96 mm x 32 mmPowering +12 VDCMounting Wall and table mounting
ComplianceEMC EN55022, CISPR-22 Class B, ETSI 300 386Safety EN60950, UL60950, CE, Optical IEC-60825-1 Class B Laser safety per G.664Environmental QM-333 ‘B2” CategoryTransient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-1010
Fiber to the Future® 19
Indoor wall or table mount
Four 10/100/1000Base-T Ethernet RJ-45 Ports
Built-in L3 routing gateway with NAT/NAPT and Firewall
Two analog 2-wire RJ-11 (POTS FXS) VoIP SIP voice ports, G.711 / G.729 / G.723 POTS FXS codec, 5 REN per port
CLASS 5 Voice Services
Built-in L2 wire-speed switch , 128/256 MAC addresses and 16/32 VLAN VIDs
MAC address limiting
Customer VID (VLAN ID) tagged (802.1Q), priority tagged (802.1p) and untagged frames, stacked VLAN (Q-in-Q)
ToS/DSCP to 802.1p mapping IGMPv1/v2/v3 snooping and fi ltering
Ethernet UNI output shaping, and upstream scheduling
GPON “dying gasp” power loss indication
AONT-1240GPON Single Family Unit Optical Network Terminal
Feature SummaryApplications The AONT-1240 has been optimized for single family homes or apartments and small home offi ces (SOHO) or small businesses that require advanced gateway functions.
High Bandwidth GPON The AONT-1240 is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. In addition, it supports down-stream AES (128-bit key) and downstream and/or upstream FEC RS(255,239).
Ethernet Quality of Service The AONT-1240 has extensive Ethernet QoS features, including 802.3x fl ow con-trol, DSCP to 802.1p mapping, upstream congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent and robust buff er and queue management for Ethernet traffi c, with individual prioritizable queues, ensures that tiered residential service off erings based on diff erent bit-rates and QoS can be supported.
Gateway The AONT-1240 contains both a built-in wire-speed L2 802.1Q VLAN switch and a built-in L3 routing gateway with Port forwarding, NAT and NAPT address transla-tion, built-in PPPoE support for HSI, and a integrated stateful Packet Inspection Firewall with a confi gurable Access Control List (ACL) and application-level gate-way (ALG). Support for VPN (L2TP, PPTP and IPSec) pass through is also provided. As part of the gateway function there is a DHCP Client and server, and a DNS server.
Security The AONT-1240 comes with the latest security features, including MAC address spoofi ng protection, MAC/IP address port binding, MAC/IP address limiting on a per port basis, per-port Access Control List (ACL) based on port, MAC address or Ether-type and DOS prevention.
Flexible Management The AONT-1240 is managed from the AOLT-4000 OLT over the GPON’s OMCI channel. The AOLT in turn is managed with either Alphion’s Element Manage-ment System (AEMS) that provides confi guration, profi le based provisioning, event and fault management and performance monitoring for the AONT, or with a 3rd party EMS using SNMP or a legacy NMS.
AONT-1240
Fiber to the Future®20
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+) ITU G.984.2 AMD1Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine Rate Upstream: 1.244 Gb/s; Downstream: 2.488 Gb/sOutput Power +0.5 to +5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmDistance up to 60 km (depending on split ratio and reach extension)Connector SC/UPC
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
Data interfacesType (wired) Four 10/100/1000Base-T RJ-45 Ether- net interfacesRate & Duplex Auto-negotiationMDI/MDIX Auto-sensingVLAN Support 802.1Q with VLAN tag manipulation as well as Legacy Mode operation, VLAN Stacking (Q-in-Q), VLAN translationMAC & VLAN Table 128/256 MAC Address and 16/32 VLAN IDs, 128 multicast groups and IGMP V2/V3 snooping, Broadcast/ Multicast rate limiting, MAC address limitingPriority CoS based on VID, 802.1p, and IP ToS/DSCP, and IP VID=0 802.1p, ToS/ DSCP to 802.1p mapping, 802.1p marking/remarking
GatewayRouting L3 software confi gurableAddress Assignment PPPoE, DHCP or StaticAddress Translation NAT/NAPT and STP fi rewall with ACL and ALG (application-level gateway)Services DHCP client and server, DNS, VPN (PPTP, L2TP, IPSec) Pass-through, Port forwarding
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
Voice interfacesType Two FXS POTS RJ-11 interfaces, ATA (Analog Telephone Adapter)VoIP Protocol SIP (Session Initiation Protocol) (RFC3261), SDP (RFC2327),TP (RFC3550/3551)Codec Multiple codec support G.711, G729A/B, G723.1DTMF RFC2833 SIP INFO or In-bandRinger 5REN per port, 55V RMS, BalancedTones and Ring Confi gurableDial Plan Confi gurableFAX and Modem G.711 for FAX/mode in TTY or T.38 FAXCLASS 5 Services Yes, Various (Caller ID, Call Waiting, Call Transfer, Call Forwarding, Three- way Calling, Distinctive Ringing...)Conditioning Echo Cancellation, Voice Activity Detection (VAD), Comfort Noise Generation(CNG)
EnvironmentalTemperature 0 to +50°CJitter Buff er Static or DynamicRelative humidity 5 to 95% (non-condensing)Mounting Wall or table mounting
ComplianceEMC EN55022, CISPR-22 Class B, ETSI 300 386, TEC SD/EMI-01/02 Sept.2001Safety EN60950, UL60950, CE, Optical IEC-60825-1 Class 1 Laser safety per G.664Laser Safety IEC-60825-1 Class 1 laser safety per G.664, FDA 21 CFR 1040.10 & 1040.11 Class 1Environmental QM-333 ‘B2” CategoryTransient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-1240
Fiber to the Future® 21
Applications The AONT-1040 has been optimized for single family homes or apart-ments and small home offi ces (SOHO) or small businesses.
High Bandwidth GPON The AONT-1040 is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. In addition, it supports down-stream AES (128-bit key) and downstream and/or upstream FEC RS(255,239).
Ethernet Quality of Service The AONT-1040 has extensive Ethernet QoS features, including 802.3x fl ow con-trol, DSCP to 802.1p mapping, upstream congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent and robust buff er and queue management for Ethernet traffi c, with individual prioritizable queues, ensures that tiered residential service off erings based on diff erent bit-rates and QoS can be supported.
Gateway The AONT-1040 contains both a built-in wire-speed L2 802.1Q VLAN switch and a built-in L3 routing gateway with Port forwarding, NAT and NAPT address trans-lation, built-in PPPoE support for HSI, and an integrated stateful Packet Inspec-tion Firewall with a confi gurable Access Control List (ACL) and application-level gateway (ALG). Support for VPN (L2TP, PPTP and IPSec) pass through is also pro-vided. As part of the gateway function there is a DHCP Client and server, and a DNS server.
Security The AONT-1040 comes with the latest security features, including MAC address spoofi ng protection, MAC/IP address port binding, MAC/IP address limiting on a per port basis, per-port Access Control List (ACL) based on port, MAC address and Ether-type, DOS prevention, WEP, and WPA/WPA2.
Flexible Management The AONT-1040 is managed from the AOLT-4000 OLT over the GPON’s OMCI chan-nel. The AOLT in turn is managed with either Alphion’s Element Management System (AEMS) that provides confi guration, profi le based provisioning, event and fault management and performance monitoring for the AONT, or with a 3rd party EMS using SNMP or a legacy NMS.
Indoor wall or table mount
Four 10/100/Base-T Ethernet RJ-45 Ports
802.11b/g/n wireless interface
Built-in L3 routing gateway with NAT/NAPT and fi rewall
Built-in L2 wire-speed switch , 128/256 MAC addresses and 16/32 VLAN VIDs
MAC address limiting
Customer VID (VLAN ID) tagged (802.1Q), priority tagged (802.1p) and untagged frames, stacked VLAN (Q-in-Q)
ToS/DSCP to 802.1p mapping IGMPv1/v2/v3 snooping and fi ltering
Ethernet UNI output shaping, and up-stream scheduling
GPON “dying gasp” power loss indication
AONT-1040GPON Single Family Unit Optical Network Terminal
Feature Summary
AONT-1040
Fiber to the Future®22
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+) ITU G.984.2 AMD1Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine Rate Upstream: 1.244 Gb/s; Downstream: 2.488 Gb/sOutput Power +0.5 to +5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmDistance up to 60 km (depending on split ratio and reach extension)Connector SC/APC
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
Video interfacesType Not applicable, IP Video (Multicast or Unicast) over the Data InterfaceData interfacesType (wired) Four 10/100Base-T RJ-45 Ethernet interfacesType (wireless) One 802.11b/g/n, two antennaSecurity WEP, WPA-PSK, MAC address fi ltering Rate & Duplex Auto-negotiationMDI/MDIX Auto-sensingVLAN Support 802.1Q with VLAN tag manipulation as well as Legacy Mode operation, VLAN Stacking (Q-in-Q), VLAN translationMAC & VLAN Table 128/256 MAC Address and 16/32 VLAN IDs, 128 multicast groups and IGMP V2/V3 snooping, Broadcast/ Multicast rate limiting, MAC address limitingTable Priority CoS based on VID, 802.1p, and IP ToS/DSCP, and IP VID=0 802.1p, ToS/ DSCP to 802.1p mapping, 802.1p marking/remarking
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
EnvironmentalTemperature 0 to +45°CJitter Buff er Static or DynamicHumidity 5% to 90% (non-condensing)
GatewayRouting L3 software confi gurableAddress Assignment PPPoE, DHCP or StaticAddress Translation NAT/NAPT and STP fi rewall with ACL and ALG (application-level gateway)Services DHCP client and server, DNS, VPN (PPTP, L2TP, IPSec) Pass-through, Port forwarding)
PhysicalW x D x H 220 mm x 160 mm x 35 mmPowering External AC adapter with 12V / 1.0A connectorMounting Wall or table mounting
ComplianceEMC EN55022, CISPR-22 Class B, ETSI 300 386, TEC SD/EMI-01/02 Sept.2001Safety EN60950, UL60950, CE, Optical IEC-60825-1 Class B Laser safety per G.664Laser Safety IEC-60825-1 Class 1 laser safety per G.664, FDA 21 CFR 1040.10 & 1040.11 Class 1Environmental EN300019-1-3 Class 3.1ETransient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-1040
Fiber to the Future® 23
Indoor wall or table mount
Four 10/100Base-T Ethernet RJ-45 Ports with auto-negotiation
Four analog 2-wire RJ-11 (POTS) VoIP SIP voice ports, G.711 codec, 5 REN per port
CLASS 5 Voice Services
Built-in L2 switch , 256 MAC addresses and 16 VLAN VIDs
MAC address limiting
Customer VLAN tagged (802.1p), prior-ity tagged and untagged frames ToS/DSCP to 802.1p mapping
IGMPv1/v2/v3 snooping and fi ltering
Ethernet UNI output shaping, and up-stream scheduling
GPON “dying gasp” power loss indica-tion
AONT-1440GPON Single Family Unit Optical Network Terminal
Feature SummaryApplications The AONT-1440 is a compact GPON ONT that can be used to provide Voice and Data services to single family homes or apartments and small home offi ces (SOHO).
High Bandwidth GPON The AONT-1440 is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. In addition, it supports down-stream AES (128-bit key) and downstream and upstream FEC RS(255,239).
Ethernet Quality of Service The AONT-1440 has extensive Ethernet QoS features, including 802.3x fl ow con-trol, DSCP to 802.1p mapping, upstream congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent and robust buff er and queue management for Ethernet traffi c, with individual prioritizable queues, ensures that tiered residential service off erings based on diff erent bit-rates and QoS can be supported.
Security The AONT-1440 comes with the latest security features, including MAC address spoofi ng protection, MAC/IP address port binding, MAC/IP address limiting on a per port basis, local port-to-port switching blocking option, 802.1X MAC-based authentication, per-port Access Control List (ACL) based on port, MAC address and Ether-type, and DOS prevention.
Flexible Management The AONT-1440 is managed from the AOLT-4000 OLT over the GPON’s OMCI chan-nel. The AOLT in turn is managed with either Alphion’s Element Management Sys-tem (AEMS) that provides confi guration, profi le based provisioning, event and fault management and performance monitoring for the AONT, or a 3rd party EMS using SNMP or a legacy NMS.
AONT-1440
Fiber to the Future®24
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+)Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine Rate Upstream: 1.24416 Gb/s; Down- stream: 2.48831 Gb/sOutput Power +0.5 to +5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmDistance up to 60 km (depending on split ratio and reach extension)Connector SC/APC
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
Video interfacesType Not applicable, IP Video over the Data interface
Data interfacesType Four 10/100Base-T RJ-45 Ethernet interfacesRate & Duplex Auto-negotiationMDI/MDIX Auto-sensingVLAN Support 802.1Q with VLAN tag manipulationMAC & VLAN Table 256 MAC Address and 16 VLAN IDsPriority VLAN 802.1p, VID=0 802.1p, ToS/ DSCP to 802.1p mapping
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
Voice interfacesType Two FXS POTS RJ-11 interfaces, 5 REN, Balance RingVoIP Protocol SIP (Session Initiation Protocol) (RFC3261 and SDP (RFC2327)Codec Multiple codec supportDTMF RFC2833 or In-bandTones and Ring Confi gurableDial Plan Confi gurableFAX and Modem G.711 for FAX/mode in TTY or T.38 FAXCLASS 5 Services Yes, VariousConditioning Echo Cancellation, Voice Activity Detection, Comfort Noise Generaliza- tion
EnvironmentalTemperature 0 to +50°CRelative humidity 5% to 95% (non-condensing)
PhysicalH x W x D 130 mm x 195 mm x 35 mmPowering +12 VDC feed via external AC/DC adapter. Optional 8-pin power input with UPS monitoringMounting Wall and table mounting
ComplianceEMC EN55022, CISPR-22 Class B, ETSI 300 386, TEC SD/EMI-01/02 Sept.2001Safety EN60950, UL60950, CE, Optical IEC-60825-1 Class B Laser safety per G.664Environmental QM-333 ‘B2” CategoryTransient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-1440
Fiber to the Future® 25
Power backup for AONT-100 and AONT-1000 series
Over 18 watt of regulated 12VDC to the load
Input overcurrent protection
Output overvoltage and overcurrent protection
Thermal shutdown protection
CE, QM 333, and QM 301 compliant
Missing battery indicator
Failed battery indicator
Up to 5 hour reserve operation in case of an AC power failure
Fully charged in 18 hours while provid-ing power to SFU
Sealed maintenance-free battery
Low-Voltage-Disconnect (LVD) circuit when battery voltage goes below 10.5V
AONT-UPSONT Uninterruptable Power Supply
Feature SummaryDescriptionThe Alphion power saving AONT-UPS protects the AONT-100 and AONT-1000 family of SFU ONTs from bad power as a result of surges and power outs. The AONT-UPS is a compact backup power solu-tion companion to the AONT-100 and AONT-1000 family of SFU ONTs. The unit can be either wall mounted or placed on the fl oor near the ONT.
Application The AONT-UPS is meant to provide uninterrupted service from the AONT-100 and AONT-1000 family of SFU ONT’s. This ensures that voice, data and internet are fully functional, even during a power outage or power surge, for up to 5 hours. When the power supply is restored, the back-up battery charges up in 18 hours or less depending on the battery discharge during the power out.
Safe and Reliable Operation The AONT-UPS comes with built in over voltage and over current protection. In addition, the unit also includes a Low-Voltage-Disconnect circuit function that disconnects the battery when it gets below 10.5V. The surge protection features help prevent damage to the Alphion ONT products that can occur due to frequent power fl uctuations.
AONT-UPS
Input Voltage Range: 160-270 VAC (EU/India) 90-240 VAC (NA)Input Frequency: 45-63 HzOutput Voltage Range: 9.2-14.7 VDC (continuously adjustable) - EU/India/NABattery cut-off : 10.25-10.6 VDC (1.0 ADC) EU/India/NA
Specifi cations
Fiber to the Future®26
AONT-3030
AONT-3030GPON Optical Network Terminal Multi-Dwelling Unit
Feature Summary19 inch rack mount
Indoor wall or rack mount
Twenty four RJ-45 fast Ethernet inter-faces
Built-in L2 switch, 1024 MAC addresses and 512 VLAN VIDs
MAC address limiting, Broadcast / Multi-cast rate limiting
Customer VLAN tagged (802.1p), priority tagged and untagged frames
ToS/DSCP to 802.1p mapping and 802.1p marking/remarking
IGMPv1/v2/v3 snooping and fi ltering
Ethernet UNI output shaping, and up-stream scheduling
GPON “dying gasp” power loss indication
Applications The AONT-3030 has been optimized for the multi-dwelling environment. High Bandwidth GPONThe AONT-3030 is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. In addition, it supports down-stream AES (128-bit key) and downstream and/or upstream FEC RS(255, 239)
Ethernet Quality of Service The AONT-3030 has extensive Ethernet QoS features, including 802.3x fl ow con-trol, DSCP to 802.1p mapping, upstream congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent and robust buff er and queue management for Ethernet traffi c, with individual prioritizable queues, ensures that tiered residential service off erings based on diff erent bit-rates and QoS can be supported.
SecurityThe AONT-3030 comes with the latest security features, including MAC address spoofi ng protection, MAC/IP address port binding, MAC/IP address limiting on a per port basis, local port-to-port switching blocking option, per-port Access Con-trol List (ACL) based on port, MAC address and Ether-type, and DOS prevention.
Flexible ManagementThe AONT-3030 is managed from the AOLT-4000 OLT over the GPON’s OMCI chan-nel. The AOLT in turn is managed with either Alphion’s Element Management System (AEMS) that provides confi guration, profi le and based provisioning, event and fault management and performance monitoring for the AONT, or with a 3rd party EMS using SNMP or a legacy NMS.
Fiber to the Future® 27
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+) ITU G.984.2 Amd1Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine rate Upstream: 1.244 Gb/s; Downstream: 2.488 Gb/sOutput power +0.5 to 5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmDistance up to 60 km (depending on split ratio and reach extension)Connector SC/APC with 30 degree access
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
PhysicalH x W x D 44 mm x 440 mm x 280 mm (without brackets)Powering 100-240 VAC, 3-pin AC power connec- tor with on/off switch and fuseMounting Rack and wall mountable
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
Fast EthernetType 24 10/100Base-T RJ-45 Ethernet interfacesRate & Duplex Auto-negotiationMDI/MDIX Auto-sensingVLAN Support 802.1Q with VLAN tag manipulation, VLAN Stacking (Q-in-Q), VLAN TranslationMAC & VLAN Table 1,024 MAC Address and 512 VLAN IDsPriority CoS based on VID, 802.1p, and IP ToS/ DSCP ToS/DSCP to 802.1p mapping, 802.1p marking / remarking
EnvironmentalTemperature 0 to +50°CHumidity 5% to 95% (non-condensing)
ComplianceEMC EN55022, CISPR-22 Class B, ETSI 300 386, TEC SD/EMI-01/02 Sept.2001Safety EN60950, UL60950, CE, Laser Safety IEC-60825-1 Class 1 laser safety per G.664, FDA 21 CFR 1040.10 & 1040.11 Class 1Environmental QM-333 ‘B2” Category, WEEE, RoHS6Transient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-3030
Fiber to the Future®28
AONT-3330
AONT-3330GPON Optical Network Terminal Multi-Dwelling Unit
Feature Summary19 inch rack mount
Indoor wall or rack mount
Twenty four RJ-45 fast Ethernet inter-faces
Twenty four analog 2-wire RJ-21 50-pin POTS VoIP SIP voice ports
CLASS 5 Voice Services
Built-in L2 switch, 1024 MAC addresses and 512 VLAN VIDs
MAC address limiting, Broadcast / Multi-cast rate limiting
Customer VLAN tagged (802.1p), priority tagged and untagged frames
ToS/DSCP to 802.1p mapping and 802.1p marking/remarking
IGMPv1/v2/v3 snooping and fi ltering
Ethernet UNI output shaping, and up-stream scheduling
GPON “dying gasp” power loss indication
Applications The AONT-3330 has been optimized for the multi-dwelling environment. High Bandwidth GPONThe AONT-3330 is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. In addition, it supports down-stream AES (128-bit key) and downstream and/or upstream FEC RS(255, 239).
Ethernet Quality of Service The AONT-3330 has extensive Ethernet QoS features, including 802.3x fl ow con-trol, DSCP to 802.1p mapping, upstream congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent and robust buff er and queue management for Ethernet traffi c, with individual prioritizable queues, ensures that tiered residential service off erings based on diff erent bit-rates and QoS can be supported.
SecurityThe AONT-3330 comes with the latest security features, including MAC address spoofi ng protection, MAC/IP address port binding, MAC/IP address limiting on a per port basis, local port-to-port switching blocking option, per-port Access Con-trol List (ACL) based on port, MAC address and Ether-type, and DOS prevention.
Flexible ManagementThe AONT-3330 is managed from the AOLT-4000 OLT over the GPON’s OMCI chan-nel. The AOLT in turn is managed with either Alphion’s Element Management System (AEMS) that provides confi guration, profi le and based provisioning, event and fault management and performance monitoring for the AONT, or with a 3rd party EMS using SNMP or a legacy NMS.
Fiber to the Future® 29
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+) ITU G.984.2 Amd1Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine rate Upstream: 1.244 Gb/s; Downstream: 2.488 Gb/sOutput power +0.5 to 5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmDistance up to 60 km (depending on split ratio and reach extension)Connector SC/APC with 30 degree access
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
Fast EthernetType 24 10/100Base-T RJ-45 Ethernet interfacesRate & Duplex Auto-negotiationMDI/MDIX Auto-sensingVLAN Support 802.1Q with VLAN tag manipulation, VLAN Stacking (Q-in-Q), VLAN TranslationMAC & VLAN Table 1,024 MAC Address and 512 VLAN IDsPriority CoS based on VID, 802.1p, and IP ToS/DSCP to 802.1p mapping, 802.1p marking / remarking
PhysicalH x W x D 44 mm x 440 mm x 280 mm (without brackets)Powering 100-240 VAC, 3-pin AC power connec- tor with on/off switch and fuseMounting Rack and wall mountable
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
Voice interfacesType FXS 24 POTS interfaces, Telco-50 connectorsVoIP Protocol SIP (Session Initiation Protocol) (RFC3261) with SDP (RFC2327) and RTP (RFC3550/3551)Codec Multiple codec support G.711, G.729A/B, G723.1DTMF RFC2833 SIP info or In-bandRing 5REN per port, 55V RMS, BalancedTones and Ring Confi gurableDial Plan Confi gurableFAX and Modem G.711 for FAX/mode in TTY or T.38 FAXCLASS 5 Services Yes, Various (Caller ID, Call Waiting, Call Transfer, Call Forwarding, Three- way Calling, Distinctive Ringing, etc.)Conditioning Echo Cancellation, Voice Activity Detection, Comfort Noise Generaliza- tionJitter Buff er Static or Dynamic
EnvironmentalTemperature 0 to +50°CHumidity 5% to 95% (non-condensing)
ComplianceEMC EN55022, CISPR-22 Class B, ETSI 300 386, TEC SD/EMI-01/02 Sept.2001Safety EN60950, UL60950, CE, Laser Safety IEC-60825-1 Class 1 laser safety per G.664, FDA 21 CFR 1040.10 & 1040.11 Class 1Environmental QM-333 ‘B2” Category, WEEE, RoHS6Transient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-3330
Fiber to the Future®30
AONT-300
AONT-300GPON Optical Network Terminal
Multi-Dwelling Unit
Feature SummaryIndoor wall or rack mount
Twenty four VDSL ports with auto fall-back to ADSL2/2+
ITU-G.993.2 compliant
SELT and DELT
VDSL2 profi le 8d, 12a and 17a
Twenty four analog 2-wire POTS ports with SIP VoIP (optional)
Class 5 voice services
AC powered with optional backup bat-tery
In built UPS with alarm monitoring
External Alarm input and output contact
Applications The AONT-300 is a GPON ONT that is optimized for deep fi ber and FTTB deploy-ments to cater to Multi Tenant buildings or apartment clusters. With 24 VDSL2 ports, the AONT-300 helps service providers to deliver high bandwidth services over existing copper wires. Optional POTS interfaces can be employed to provide voice services over the same copper pair. High Bandwidth GPON and VDSL2The AONT-300 is fully FSAN (ITU-T G.984) compliant with a 1.244 Gb/s upstream and 2.488 Gb/s downstream, Class B+ GPON system. The VDSL2 subscriber inter-faces allow service providers to provide high bandwidth services to subscribers without having to deploy fi ber all the way home. This proves an ideal platform for carriers who are looking to do a gradual migration to a FTTH off ering.
Robust Quality of Service The AONT-300 provides a comprehensive suite of QoS enforcement features in-cluding congestion control, and downstream traffi c scheduling for premium or time sensitive content. Intelligent buff er and queue management, with individu-ally prioritized queue management, ensures that tiered residential service off er-ing can be supported.
Cost Eff ective SolutionsThe AONT-300 enables service providers to reduce the time-to-market for their broadband service off ering by reusing the existing in building copper in multi dwelling units. With a high bandwidth GPON ONT in the basement of a MDU or at a curb, it is economical to reuse the existing copper wiring using the VDSL2 ports and off er FTTH like service until the time fi ber to each home can be rolled out.
Flexible ManagementThe AONT-300 is managed from the AOLT-4000 OLT over the GPON’s OMCI chan-nel. The AOLT in turn is managed with either Alphion’s Element Management System (AEMS) that provides confi guration, profi le and based provisioning, event and fault management and performance monitoring for the AONT, or with a 3rd party EMS using SNMP or a legacy NMS.
Fiber to the Future® 31
SPECIFICATIONS
Optical interfaceStandard GPON; fully ITU-T G.984 compliantLink Budget 28 dB (Class B+) Wavelength Upstream: 1310 nm; Downstream: 1490 nmLine rate Upstream: 1.244 Gb/s; Downstream: 2.488 Gb/sOutput power +0.5 to 5.0 dBmSensitivity* -27 dBm (at 10 dB extinction ratio)Overload -8 dBmDistance up to 60 km (depending on split ratio and reach extension)Connector SC/APC
GPON TC LayerFEC & AES AES (128-bit key) and FEC RS (255,239)DBA YesNo. Gem Ports Number is software dependentNo. TCONT/AllocID Number is software dependent
Video InterfaceType Not applicable, IP Video over the VDSL2 interfaces
VDSL2 InterfaceType Twenty four (24) ITU-T G.993.2 compliant VDSL2 portsProtocol VDSL2 (ITU-T G.993.1), ADSL2/2+ (ITU-T G.992.5)Spectrum Management DPBO, UPBO, RFI BandsBand Profi le 8d, 12a, 17aPOTS Splitter ExternalProfi le Management VOP as per TR-165
*Measured at BER better than 1x10-10, factoring in aging and worst case PMD.
Voice interfacesType Twenty four (24) FXS POTS RJ-11 interfaces, 5 REN, Balance RingVoIP Protocol SIP (Session Initiation Protocol) (RFC3261) and SDP (RFC2327) Codec G.711, G.726, G729a/bDTMF RFC2833 or In-bandTones and Ring Confi gurableDial Plan Confi gurableFAX and Modem G.711 for FAX/mode in TTY or T.38 FAXCLASS 5 Services Yes, Various Conditioning Echo Cancellation, Voice Activity Detection, Comfort Noise Generaliza- tion
EnvironmentalLine Protection ITU-T K.20Temperature 0 to +50°CHumidity 5% to 95% (non-condensing)
PhysicalStorage Temperature -40 to +85°CH x W x D 133 mm x 439 mm x 285 mmPowering +12 VDC feed via external AC/DC adapter, Optional 8-pin power input with UPS MonitoringInput Voltage 160 VAC to 250 VAC, 47 to 63 HzPower Consumption 100W (All ports active, battery fully charged)Battery Backup External Lead AcidMounting Rack mount
ComplianceEMC EN55022, CISPR-22 Class B, ETSI 300 386, TEC SD/EMI-01/02 Sept.2001Safety EN60950, UL60950, CE, Optical IEC- 60825-1 Class B laser safety per G.664Environmental QM-333 ‘B2” CategoryTransient EN/IEC61000-4-4 (2001) level 2Radiant RF Immunity EN/IEC61000-4-3 (2002) level 2Conducted Immunity EN-IEC61000-4-6 (2001) level 2Surge EN/IEC61000-4-5 (2001) 0.5 KV (line) and 1.5 KV (earth)ESD EN/IEC61000-4-2 (2001) Contact level 2 & air discharge level 3
AONT-300
Fiber to the Future®32
ARGT-1040
ARGT-1040VDSL Residential Gateway Terminal
Feature SummarySupports VDSL2 profi le up to 17a
Data rates up to 100Mb/s downstream and 50 Mb/s upstream
Triple play applications
Embedded fi rewall to block intrusions and malicious attacks
Four 10/100 Ethernet ports
Automatic speed-sensing and crossover correction
PPP, IP routing, NAT/fi rewall, and DHCP server/relay/client
Browser-based confi guration and man-agement
TR-069 or SNMP for remote manage-ment
Firmware upgrades available through HTTP or TFTP
Compact size
DescriptionThe Alphion Residential Gateway Terminal 1040 is a compact VDSL router that gives unparalleled broadband service over a pair of copper wire. For service providers that are migrating to a FTTx ser-vice model, use of the ARGT-1040 in conjunction with the Alphion GPON MDU AONT-300 off ers a cost eff ective solution to off er high bandwidth media rich applications while reus-ing existing copper. High Bandwidth The ARGT-1040 is designed to interoperate seamlessly with Alphion AONT-300 VDSL2 - GPON MDU or standard DSLAMs from any telecom vendor. With cutting edge Residential Gateway features and high bandwidth VDSL2 WAN interfaces, the ARGT-1040 off ers enough bandwidth to ensure that the subscribers can be off ered interactive triple play applications over existing copper connections.
Quality of Service The ARGT-1040 is a feature rich residential gateway that supports extensive QoS features including classifi cation rules, priority queuing, IP TOS/Precedence, 802.1p marking, Diff Serv DSCP marking to enable service providers to off er delay and quality sensitive applications like VoIP and IPTV.
VersatilityThe ARGT-1040 supports fallback to ADSL2/2+ mode of operation when the ser-vice distance exceeds the range that VDSL2 standards. This allows service provid-ers the fl exibility to increase the range of their serving area using existing infra-structure although with a lower bandwidth. The integrated Ethernet switch in the ARGT-1040 features automatic crossover-correction and speed sensing to ensure simple plug and play applications for the residential user.
Flexible ManagementThe user can manage and confi gure the ARGT-1040 through a simple Web based GUI. The ARGT-1040 supports TR-069 standards that can optionally allow confi gu-rations of the VDSL2 Residential Gateways using a centralized ACS Server.
Fiber to the Future® 33
SPECIFICATIONS
WAN interfaceType VDSL2 (ITU-T G.993.1) with fallback to ADSL2+ (ITU-T G.992.5)VDSL2 Band Profi le 8d, 12a, 17a
LAN interfaceType Four 10/100Base-T RJ-45 Ethernet interfaceRate & Duplex Auto-negotiationMDI/MDIX Auto-sensing
Confi guration managementWeb Based GUIOptional TR-069UPnP
EnvironmentalOperating Temperature 0 to +40°COperating Humidity 5% to 95% (non-condensing)Storage Temperature -20 to +70°CStorage Humidity 5% to 95% (non-condensing)
PowerAC adapter Input 100-270 VAC, 50-60 Hz; Output 12 VDC, 0.7 A
DimensionsW x D x H 220 mm x 150 mm x 33 mm
Software featuresMAC Encapsulation Routing (MER)802.1p/q VLAN over RFC 2684PPPoE PassthroughDHCP client, server and relay agentDNS relayRouting Information Protocol (RIP) v1 and v2NAT / PATIGMP Proxy and IGMP SnoopingARP
FirewallStateful inspectionDoS PreventionTCP/IP/Port/Interface Filtering RulesMAC Layer FilteringParental Controls
QoSRouted and Bridge mode PVCs for packet level QoSClassifi cation RulesIP TOS/Precedence802.1p Diff Serv DSCP markingSource/Destination MAC addresses classifi cation
Regulatory compliancesCE 89/336/EEC(EN55022/24), 2004/108/ECFCC CFR 47 Part 15 BAS/NZS CISPR 22IEC60950-1UL60950-1CSA60950-1EN60950-1
ARGT-1040
Fiber to the Future®34
ASPL Series
ASPL SeriesGPON Passive Optical Splitter
Feature SummaryHigh channel count
Superior uniformity
Low polarization dependent loss (PDL)
Rugged metallic enclosure
Wall mount / Rack mount
Protection and coiling for the input patch cord / fi ber pigtail to enable proper termination
Lockable with optional padlock
Cost Eff ectiveAlphion’s family of passive opti-cal splitters off er a cost eff ective solution that allows service pro-viders to distribute content from a single fi ber to multiple sub-scribers through a point-to-multipoint architecture facilitated through the use of optical splitters. These splitters can be arranged in a single, centralized fashion or distributed in a cascaded confi guration. Since the network is purely passive, it is essential that splitter loss is kept to a minimum. Alphion’s splitter family is de-signed and manufactured to insure minimal splitter loss and maintain uniformity, thereby improving optical reach. Flexible Confi guration Alphion’s ASPL series of passive optical splitters are available in a range of confi gu-rations for designing an optimized PON network. Available options include 1x2, 1x4, 1x8, 1x16, 1x32 and 1x64. For networks that employ fi ber path protection, the ASPL series of splitters also include the following confi gurations - 2x2, 2x4, 2x8, 2x16, 2x32 and 2x64.
The ASPL series of splitters also include indoor rack mount splitter options that employ stan-dard LGX cartridge to provide 1x2, 1x4, 2x2 and 2x4 confi gurations.
Fiber to the Future® 35
SPECIFICATIONS
Insertion loss maximum (dB)(CR)1 x 2 4.01 x 4 7.11 x 8 10.51 x 16 13.81 x 32 17.11 x 64 20.52 x 2 4.22 x 4 7.42 x 8 11.02 x 16 14.62 x 32 17.82 x 64 20.5
Uniformity maximum (dB)1 x 2 0.31 x 4 0.51 x 8 0.81 x 16 1.01 x 32 1.31 x 64 2.02 x 2 1.12 x 4 1.22 x 8 1.62 x 16 2.42 x 32 3.02 x 64 3.6
Insertion loss maximum (dB)(CR)1 x n, 2 x n 1260-1360 nm / 1480-1580 nm
*The optical specifi cations are net without the connectors
PDL (dB)<0.2 (<0.3 for 2 x 64)
Return Loss (dB)>55
Directivity (dB)<55
Fiber TypeSingle mode fi ber (ITU-T G.652)
Operating and Storage temperature-40 to +85°C
ComplianceTEC GR No. GR/PON-01/02-AR.2008
Connector Specifi cationsInsertion Loss Mated pair - 0.3 dB max
Return Loss UPC - 50 dB min APC - 60 dB minFerrule material Ceramic (Zirconia)Adapter sleeve Ceramic (Zirconia)Compliance TEC GR No. GR/OFJ-02/01.MAY.2004
ASPL Series
Fiber to the Future®36
AEMS
AEMSElement Management System
Feature SummaryJ2EE based three-tier architecture with customized functions
Single EMS supports 500 OLTs and 640,000 ONT/ONUs
SSL based secured communication
Secure certifi cate and RADIUS based ac-cess, with customizable user and profi le based authorization
Graphical, Geographical, Hierarchical and Domain based Network View
Point & Click Wizard based provisioning
Service Profi le management
Performance monitoring
Alarm and Event monitoring
Security management
ApplicationsThe AEMS is a full featured Element Man-agement System that is used to provision, confi gure and manage Alphion’s portfolio of FTTx products. Scalable Architecture The AEMS is based on a J2EE three-tier ar-chitecture with customizable functions run-ning on Solaris 10 or linux. A single installa-tion of the AEMS can support 500 OLTs and up to 640,000 ONTs.
Network/Topology View AEMS provides a graphical, geographical, hierarchical, and domain based view of the AOLT-4000 network elements (NEs) and the interconnecting links. The visual maps display the NEs and the links in diff erent colors depending on their status, with green indicating healthy status, amber/yellow indicating degraded condi-tion, and red indicating a critical alarm condition.
AEMS’ network view facilitates simplifi ed confi guration, fault, and performance management by allowing the operator to zoom in from a domain, sub-network or ring level down to a port in one of the cards in a NE.
Confi guration Management AEMS supports service provisioning, equipment provisioning, connection provi-sioning, and NE software image download, as per ITU-T G.984.x:
• Creation, deletion, update, and viewing of the managed network topology data• Provision/Unprovision service on an NE• Restart NEs, cards and ports• Creation/Deletion of NEs in to from the NE management domain• NE equipment confi guration, including equipment protection to cards and ports• Activating / Deactivating / Forcing / Locking protection switching• Error detection thresholds• Software image download• Ethernet bandwidth management
Inventory Management AEMS discovers and notifi es in real time the insertion and removal of any physical card in an NE. It also reports the usage of cord resources and keep track of network inventory, reporting changes in chronological order.
Fiber to the Future® 37
SPECIFICATIONS
Fault ManagementAEMS supports fault management functions as described in the ITU-T G.984.x standards.• Performs persistency checks automatically on a received alarm
clear notifi cation, before reporting a failure or restoration event to the operator
• All failure and restore events are time-stamped• AEMS supports alarm correlation (fi ltering and suppression) to
avoid multiple alarms from a single, common source of failure• Intuitive, real-time graphical display and processing of alarms,
with the type, occurrence, severity, probable cause and clear-ing information
• Real-time visual display of NEs’ statusAlarm and Event SurveillanceAEMS allows monitoring the health of any card in a NE in an AOLT-4000 GPON access network, with a setable periodicity of a day, week, or a month. AEMS alarm surveillance functions include:• Archival of alarms (including path alarms) and status, with
the type, occurrence, severity, probable cause and clearing information
• Assignment of alarm severity• Archival of historical alarm for a minimum of 30 days• On-line logging of historical alarms and events, with alarm /
event type, alarm severity, day and time occurrence informa-tion
• Alarm fi ltering / search capabilities for historical alarms and events
Performance MonitoringAEMS supports performance management functions in accor-dance with ITU-T G.984.x standards for GPON and RFC 2544 for Ethernet interfaces. • Scheduled performance data collection / logging at confi gu-
rable launch time & rate• Confi guration of error counter thresholds• Ethernet statistics (FCS errors, dropped frames, etc.)• Flexible archival, reporting, and transferring or performance
data• Archive performance data for a month• On-demand and automated, periodic reporting (including
daily, weekly, and monthly) of performance dataCalendar ManagementAEMS can schedule administrative operations to be performed repeatedly at a particular time of day. These operations can include NE confi guration backup, software image download, performance data retrieval, operator login/logout attempts, etc.
NE Software Management• Loading of new NE software images• Management of multiple versions of NE software on the same
network• Management of multiple software image versions on the
same NE (e.g. active and standby images)• Installation of software updates• Software download status reporting• Administrator authorization for the loading of NE software
from local or remote operator terminalsDatabase Management• Support for a multi-user accessible database server, with a
minimum of 25 concurrent users (including local and remote terminals)
• Database management software support system data, soft-ware version, and database backup
Security• SSL based secured communication• Secure certifi cate and RADIUS based access, with customiz-
able user and profi le based authorization• Privileged operations requires a login password• Reporting of all login and logout attempts in a security log fi leFault Tolerance• Dual homed connectivity to two gateway NEs (GNEs) of a sub-network ensures EMS connectivity on the failure of the AOLT-4000-CTL control card of one of the NEs• No deterioration in existing services on total loss of EMS con-nectivity; ON restoration of EMS connectivity, AEMS will “sync up” with the control cards, which can hold up to 6,400 perfor-mance and fault events, with a minimum of 100 alarms• On total loss of EMS connectivity, LCT privilege remains for monitoring and local confi gurations• Supports a disaster recovery EMS server and its interconnec-tion to an existing server, and operate ability to switch over between them• Supports diagnostics software to trouble-shoot EMS faultsSNMP InterfaceThe AEMS provides a SNMP v2 or SNMP v3 interface on the Southbound interface to communicate with AOLT-4000 Sys-tem.Northbound InterfaceNorthbound CORBA / XML based interface.
AEMS
Fiber to the Future®38
PON Reach Extension System
Feature SummaryTransparent all optical reach extension for all PON technologies - BPON, GPON and EPON
Compliant with ITU-T G.984.6 recom-mendation for GPON reach extension
Transparent to any vendor-specifi c im-plementation of GPON frame structure
Completely self confi guring, Plug N Play implementation
Ability to provide 128 subscribers / PON port at 60 km reach
Utilizes Alphion QLight® semiconductor optical amplifi er (SOA) technology
Utilizes 40 nm (1310 + 20 nm) optical fi lter in upstream direction to limit SOA amplifi ed spontaneous emission (ASE)
Single RU chassis fi ts into 19” standard rack, 600 mm ETSI rack or 23” rack using mounting adapters
Redundant -48 V power supplies
Front panel access to all interfaces
Management via OMCI or SNMPv2
Easy integration to third party EMS
DescriptionThe AEXT-5100 Series of GPON Reach Extension products is an innovative solution that Alphion provides to cater to the needs of FTTx service providers that require a technology / product to enable them to extend the reach of their existing Central offi ce PON OLTs without having to put in remote OLTs to serve a cluster of sub-scribers. The AEXT-5100 PON.ext™ products are based on Alphion’s proprietary QLight® technology platform for the manufacturing of advanced discrete photon-ic integrated circuits (PICs). Because the AEXT-5100 PON.ext™ products use the same InP semiconductor technology used in virtually all telecom lasers, it is able to amplify signals at 1310 and 1490 nm, wavelengths not accessible with commer-cial fi ber-amplifi er (EDFA) technology. Due to extremely fast response time of the InP semiconductor optical amplifi er inside the PON.ext™ can accommodate both continuous (downstream) and bursty (upstream) traffi c. Alphion’s proprietary ap-proach to the incorporation of gain elements, optical fi lters, wavelength division multiplexers, input and output power detectors, as well as the associated control electronics for adiabatic gain control insures high and uniform performance over the lifetime of the PON.ext™. Central Offi ce Consolidation As service providers worldwide put an increased emphasis on rural connectivity spurred on by government support, they realize that cluster of subscribers are not usually within the serving area of a typical PON OLT system. For carriers faced with the option of installing and managing remote OLTs or setting up multiple small central offi ce, the Alphion AEXT-5100 off ers a cost eff ective alternative. The AEXT-5100 off ers the ability to extend the reach of a standard PON port to 60 km thereby eliminating the need to setup multiple central offi ces. Even within urban areas, the use of reach extension technology allows service providers to consider-ably reduce their CAPEX and OPEX budgets by collapsing multiple central offi ces into a single facility.
Increased Port Utilization The AEXT-5100 allows service providers to deploy up to 128 subscribers on a sin-gle GPON Port thereby doubling the subscriber capacity of existing GPON system. This increased capacity can be provided simultaneously with the increased reach of 60 km enabling carriers to rapidly and cost eff ectively increase both their reach and capacity.
PON ext®
Fiber to the Future® 39
SPECIFICATIONS
DownstreamWavelength range 1480-1500 nmInput power at OLT port -23 dBm min to -15 dBm maxMinimum optical gain +23 dB port to port at -23 dBm downstream input powerMax optical gain +2 dB port to port at -23 dBm excursion downstream input powerMin saturation output power (3 dB) +8 dBm
Max optical noise fi gure +9.5 dB, at -23 dBm downstream input power+5 max ASE optical power in 1400-1600 nm range emitted from ONTs port relative to output signal power (at -23 dBm down-stream input power)+9 max ASE optical power in 1200-1400 nm range emitted from ONT’s port (at -28 dBm upstream input power)
Additional Specifi cationsPower Supply -48 V redundantPower Consumption 30 W at room temperature; 34 W at 50°CManagement Interface 10/100Base-T RJ-45Craft Terminal USB 2.0
EnvironmentalTemperature +5 to +50°CRelative Humidity 5% to 85% operating and 5% to 90% short-term (non-condensing)
PON ext®
UpstreamWavelength range 1290-1320 nmInput power at ONT port -28 dBm min to -19 dBm maxMinimum optical gain +26 dB port to port at -28 dBm upstream input powerMax optical gain +4 dB port to port at -28 dBm excursion upstream input powerMin saturation output power (3 dB) +7 dBm
Max optical noise fi gure +8 dB, at -28 dBm upstream input power+7 dBm max ASE optical power in 1285-1335 nm range from OLT port relative to output signal power (at -28 dBm upstream input power)-4 dB max combined ASE optical power in 1200-1285 nm and 1335-1400 nm ranges from OLT port relative to output signal power (at -28 upstream input power)+2 dB max ASE optical power in 1400-1600 nm range emitted from OLT port (at -23 dBm downstream input power)
General Optical Specifi cations+32 dB min optical return loss looking out from OLT port into OTL or from ONTs port looking into ODNOptical connector SC/APC
Fiber to the Future®40
Contacts
Main Offi ce:Alphion Corporation
196 Princeton Hightstown Road, Building 1APrinceton Junction, New Jersey, 08550 USA
Main: +1.609.936.9001Fax: +1.609.936.9002
Website: [email protected]
Sales Representatives
Americas:
James FasanoAlphion CorporationTel: +1.609.936.9001Fax: +1.609.936.9002
E-mail: [email protected]
EMEA:
Boris StefanovAlphion Corporation
Tel: +1.609.936.9001 ext. 7070Fax: +1.609.936.9002
E-mail: [email protected]
India (Mumbai):
Bijoy MishraAlphion Communications Pvt. Ltd.
Tel / Fax: +91.22.28223533E-mail: [email protected]
India (Gurgaon):
Paresh ShahAlphion Communications Pvt. Ltd.
Tel: +91.98.1041.7253VoIP: +1.732.415.4039
E-mail: [email protected]
Singapore:
Tan Chong HeeAlphion CorporationTel: +65.8399.5960
E-mail: [email protected]